SERVICE MANUAL
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining thesafety and performance of the set.
This document has been published to be used forafter sales service only.The contents are subject to change without notice.
OUTLINE AND DIFFERENCES FROM BASE MODELOUTLINE.................................................................... iLIST OF CHANGED PARTS...................................... i
SAFETY PRECAUTIONIMPORTANT SERVICE SAFETY PRECAUTION........................................................... iiPRECAUTIONS A PRENDRE LORS DE LA REPARATION ...........................................................iiiPRECAUTIONS FOR USING LEAD-FREE SOLDER .................................................................. ivPRECAUTIONS IN SERVICING THE HDCP-KEY ROM.................................................................. v
CHAPTER 1. SPECIFICATIONS[1] SPECIFICATIONS .................................................1-1
CHAPTER 2. OPERATION MANUAL[1] OPERATION MANUAL ..........................................2-1
CHAPTER 3. DIMENSIONS[1] DIMENSIONS ........................................................3-1
CHAPTER 4. REMOVING OF MAJOR PARTS[1] REMOVING OF MAJOR PARTS ...........................4-1
Parts Guide
TopPage
CONTENTS
In the interests of user-safety (Required by safety regulations in some countries) the set shouldbe restored to its original condition and only parts identical to those specified should be used.
LCD COLOR TELEVISIONNo. S38I1LCC6554U
LC-C6554U
LC-C6554UMODEL
OUTLINEThis model is based on the LC-65D64U and is changed some parts. This Service Manual covers the modificationsalone. For the other points, refer to the LC-65D64U (Revised Edition) (No. SY7C3LC65D64U) Service Manual.
LC-C6554U
i
LC-C6554U Service Manual
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINEThis model is based on the LC-65D64U and is changed some parts. This Service Manual covers the modifications alone. For the other points, refer tothe LC-65D64U (Revised Edition) (No. SY7C3LC65D64U) Service Manual.
LIST OF CHANGED PARTS
Ref. No. DescriptionLC-65D64U
Revised Edition(No. SY7C3LC65D64U)
LC-C6554U(No. S38I1LCC6554U) Note
PRINTED WIRING BOARD ASSEMBLIESTERMINAL Unit DUNTKE208FM01 ← Some parts changedR/C, LED Unit DUNTKE264FM02 ← Some parts changedKEY Unit DUNTKE266FM02 ← —SIDE Unit DUNTKE488FM01 ← —MAIN Unit DUNTKE558FM01 ← Some parts changedSUB POWER Unit RDENCA246WJQZ ← —POWER Unit RDENCA247WJQZ ← —
LCD PANELLCD Panel Module Unit R1LK645D3LZ40Z R1LK645D3LZ40V —
TERMINAL UnitC539 Capacitor VCKYCY1EF104ZY — DeleteC543 Capacitor VCKYCY1EF104ZY — DeleteC547 Capacitor VCAAPF1CJ396MY — DeleteQ501 Transistor VS2SA1530AR-1Y VS2SA1162Y/-1Y ChangeQ503 Transistor VS2SA1530AR-1Y VS2SA1162Y/-1Y ChangeQ505 Transistor VS2SA1530AR-1Y VS2SA1162Y/-1Y ChangeQ509 Transistor VS2SA1530AR-1Y VS2SA1162Y/-1Y ChangeQ510 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ1101 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ1102 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
R/C, LED UnitQ102 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ103 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ104 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ106 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ107 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y Change
MAIN UnitC1619 Capacitor VCKYCZ1EF104ZY — DeleteC1621 Capacitor RC-KZA520WJQZY — DeleteC1631 Capacitor RC-KZA520WJQZY — DeleteC8075 Capacitor VCKYCZ1AB104KY — DeleteC8127 Capacitor VCKYCZ1AB104KY — DeleteC8128 Capacitor VCKYCZ1AB104KY — DeleteIC1403 IC VHiAK4682EQ-1Y VHiAK4682AE-1Y ChangeIC1604 IC VHiSii9185+-1Q VHiSii9185A-1Q ChangeQ1307 Transistor VS2SA1530AR-1Y VS2SA1162Y/-1Y ChangeQ2214 Transistor VS2SC3928AR-1Y VSKTC3875SG-1Y ChangeQ9301 Transistor VS2SA1530AR-1Y VS2SA1162Y/-1Y ChangeR8012 Resistor VRS-CZ1JF000JY — DeleteR8056 Resistor VRS-CZ1JF000JY — DeleteR8058 Resistor VRS-CZ1JF000JY — DeleteR8141 Resistor VRS-CZ1JF000JY — Delete
CABINET AND MECHANICAL PARTS Please refer to a Parts list
PACKING PARTS AND ACCESSORIES Please refer to a Parts list
LC-C6554U
LC-C6554U Service ManualSAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire &Shock Hazard)Before returning the receiver to the user, perform the followingsafety checks:
3. Inspect all lead dress to make certain that leads are not pinched,and check that hardware is not lodged between the chassis andother metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,insulation materials, cabinet backs, adjustment and compartmentcovers or shields, isolation resistor-capacitor networks, mechanicalinsulators, etc.
5. To be sure that no shock hazard exists, check for leakage current inthe following manner.
• Plug the AC cord directly into a 110-240 volt 50/60Hz AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-leled by a 0.15µF capacitor in series with all exposed metal cabinetparts and a known earth ground, such as electrical conduit or elec-trical ground connected to an earth ground.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having areturn to the chassis (antenna, metal cabinet, screw heads, knobsand control shafts, escutcheon, etc.) and measure the AC voltagedrop across the resistor.
All checks must be repeated with the AC cord plug connectionreversed. (If necessary, a nonpolarized adaptor plug must be usedonly for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) ormore is excessive and indicates a potential shock hazard whichmust be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICEMany electrical and mechanical parts in LCD color television havespecial safety-related characteristics.
These characteristics are often not evident from visual inspection, norcan protection afforded by them be necessarily increased by usingreplacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics areidentified in this manual; electrical components having such featuresare identified by " " and shaded areas in the Replacement Parts Listand Schematic Diagrams.
For continued protection, replacement parts must be identical to thoseused in the original circuit.
The use of a substitute replacement parts which do not have the samesafety characteristics as the factory recommended replacement partsshown in this service manual, may create shock, fire or other hazards.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
CAUTION : FOR CONTINUED PROTECTIONAGAINST A RISK OF FIRE REPLACE ONLY WITHSAME TYPE FUSE.
F0001 (250V 15A)F0003 (250V 1.6A)F0101 (250V 8A)F0701 (250V 8A)
DVM
AC SCALE
1.5k ohm10W
TO EXPOSEDMETAL PARTS
CONNECT TOKNOWN EARTHGROUND
0.15 µF
TEST PROBE
ii
LC-C6554U
PRECAUTIONS A PRENDRE LORS DE LA REPARATIONDe nombreuses pièces, électriques et mécaniques, dans les télévi-seur ACL présentent des caractéristiques spéciales relatives à la sé-curité, qui ne sont souvent pas évidentes à vue. Le degré de protec-tion ne peut pas être nécessairement augmentée en utilisant despièces de remplacement étalonnées pour haute tension, puissance,etc.Les pièces de remplacement qui présentent ces caractéristiques sontidentifiées dans ce manuel; les pièces électriques qui présentent cesparticularités sont identifiées par la marque " " et hachurées dans laliste des pièces de remplacement et les diagrammes schématiques.
Pour assurer la protection, ces pièces doivent être identiques à cellesutilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pasles mêmes caractéristiques que les pièces recommandées par l'usine,indiquées dans ce manuel, peut provoquer des électrocutions, incen-dies, radiations X ou autres accidents.
AVERTISSEMENT
1.
2.
3.
4.
5.
•
•
•
•
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
N'entreprendre aucune modification de tout circuit. C'est danger-eux.
Débrancher le récepteur avant toute réparation.
Inspecter tous les faisceaux de câbles pour s'assurer que les filsne soient pas pincés ou qu'un outil ne soit pas placé entre le châs-sis et les autres pièces métalliques du récepteur.
Inspecter tous les dispositifs de protection comme les boutons decommande non-métalliques, les isolants, le dos du coffret, les cou-vercles ou blindages de réglage et de compartiment, les réseauxde résistancecapacité, les isolateurs mécaniques, etc.
S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant lafuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une prise de cou-rant de 110-240V 50/60Hz. (Ne pas utiliser de transformateurd'isolation pour cet essai).
A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ10 watts en parallèle avec un condensateur de 0.15µF en sérieavec toutes les pièces métalliques exposées du coffret et une terreconnue comme une conduite électrique ou une prise de terrebranchée à la terre.
Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pourmesurer la chute de tension en travers de la résistance.
Toucher avec la sonde d'essai les pièces métalliques exposées quiprésentent une voie de retour au châssis (antenne, coffret métalli-que, tête des vis, arbres de commande et des boutons, écusson,etc.) et mesurer la chute de tension CA en-travers de la résistance.Toutes les vérifications doivent être refaites après avoir inversé lafiche du cordon d'alimentation. (Si nécessaire, une prised'adpatation non polarisée peut être utilisée dans le but de termin-er ces vérifications.)La tension de pointe mesurèe ne doit pas dépasser 0.75V (corre-spondante au courant CA de pointe de 0.5mA).Dans le cas contraire, il y a une possibilité de choc électrique quidoit être supprimée avant de rendre le récepteur au client.
PRECAUTION: POUR LA PROTECTION CON-
TINUE CONTRE LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
F0001 (250V 15A)
F0003 (250V 1.6A)
F0101 (250V 8A)
F0701 (250V 8A)
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifica-
tions suivantes.
DVM
ECHELLE CA
1.5k ohm10W
0.15 µF
SONDE D'ESSAI
AUX PIECESMETALLIQUESEXPOSEES
BRANCHER A UNETERRE CONNUE
AVIS POUR LA SECURITE
iii
LC-C6554U
PRECAUTIONS FOR USING LEAD-FREE SOLDEREmploying lead-free solder• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated solderingbit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may bepeeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm thesteady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit asrequired.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
PARTS CODE PRICE RANK
PART DELIVERY DESCRIPTION
ZHNDAi123250E BL J φ0.3mm 250g (1roll)ZHNDAi126500E BK J φ0.6mm 500g (1roll)ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
iv
LC-C6554U
PRECAUTIONS IN SERVICING THE HDCP-KEY ROMThe HDCP-KEY ROM shall be protected and managed for its information inside. In servicing this ROM, therefore, take the following information pro-tection/management measures.
1) When disposing of the component parts and PWBs, destruct the IC itself in a proper way.
(For repairing or replacing the component parts and PWBs as well as clearing those in stock)
2) In storing the component parts, protect and manage them against theft and disclosure.
(For storing the service parts, service units, etc.)
Applied part: HDCP-KEY ROMIC8451 RH-IXC318WJQZY (updated ROM)
v
LC-C6554U
1 – 1
LC-C6554U Service Manual CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
Item Model: LC-C6554U
LCD panel65"screen size class Advanced Super View & BLACK TFT LCD
(Diagonal Measurement : 6433/64 )"
Resolution 2,073,600 pixels (1,920 1,080)
TVFunction
TV-standard (CCIR) American TV Standard ATSC/NTSC System
ReceivingChannel
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
Digital TerrestrialBroadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)1-135ch (non-scrambled channel only)
Audio multiplex BTSC System
Audio out 15W 2
Terminals
Rear
INPUT 1 AV in, COMPONENT in
INPUT 2 AV in, S-VIDEO in
INPUT 5 HDMI in with HDCP
INPUT 6 Audio in, HDMI in with HDCP
INPUT 7 15-pin mini D-sub female connector, Audio in (Ø 3.5 mm jack)
ANT/CABLE 75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
DIGITAL AUDIO OUTPUT Optical Digital audio output 1 (PCM/Dolby Digital)
OUTPUT Audio out
RS-232C 9-pin D-sub male connector
Side
INPUT 3 AV in, COMPONENT in
INPUT 4 HDMI in with HDCP
SERVICE Software update
OSD language English/French/Spanish
Power RequirementAC 120 V, 60 Hz (FOR NORTH AMERICA)AC 110-240 V, 50/60 Hz (FOR OTHERS)
Power Consumption 525 W (0.35 W Standby with AC 120V)
WeightTV + stand 121.3 lbs./55.0 kg
TV only 110.3 lbs./50.0 kg
Dimension*2
(W H D)
TV + stand 6011/64 40 15
7/8 inch
TV only 6011/64 37
11/64 3
7/8 inch
Operating temperature 32°F to 104°F (0°C to 40°C)
*1Emergency alert messages via Cable are unreceivable.
*2The dimensional drawings are shown on the inside back cover.As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for productimprovement without prior notice. The performance specification figures indicated are nominal values of production units.There may be some deviations from these values in individual units.
LC-C6554U
LC-C6554U Service Manual CHAPTER 2. OPERATION MANUAL[1] OPERATION MANUAL
Part Names
TV (Front)
OPC indicator
POWER indicator
OPC sensor
Remote control sensor
SLEEP indicator
TV (Rear/Side)
INPUT 3terminals
RS-232Cterminal
DIGITAL AUDIOOUTPUT terminal
INPUT 6 terminals(HDMI)
INPUT 7 terminals(PC-IN)
INPUT 5 terminal(HDMI)
Antenna/Cable in INPUT 1 terminals
AC INPUT terminal
INPUT 2 terminalsAUDIO OUTPUTterminals
POWER button
MENU button
INPUT button
Channel buttons(CH / )
Volume buttons
(VOL / )
INPUT 4terminal (HDMI)
SERVICEterminal
2 – 1
LC-C6554U
Part Names
1 TV POWER:Switch the TV power on or enters standby.
2 DISPLAY:Display the channel information.
3 SOURCE POWER: Turns the power of the external equipment
on and off.
4 External equipment operational buttons:Operate the external
equipment.
5 0_9: Set the channel.
6 (DOT):
7 INPUT: Select a TV input source. (TV, INPUT 1, INPUT 2, INPUT 3,
INPUT 4, INPUT 5, INPUT 6, INPUT 7)
8 VOL / : Set the volume.
9 SURROUND: Select Surround settings.
10 FREEZE:Set the still image. Press again to return to normal
screen.
11 EXIT: Turn off the menu screen.
12 OPTION: Display the AQUOS LINK MENU screen. This button
will function only when AQUOS LINK is used.
13 REC STOP: Stops one touch recording. This button will function
only when AQUOS LINK is used.
14 SLEEP:Set the sleep timer.
15 AUDIO: Selects the MTS/SAP or the audio mode during multi-
channel audio broadcasts.
16 FUNCTION: Switches the remote control for TV, CBL/SAT, VCR,
DVD and AUDIO operation. Indicator lights up for the current
mode.
* To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
17 LIGHT :When this button is pressed, some buttons (for
example,VOL / and CH / ) on the remote control unit will
light. The lighting will turn off if no operations are performed within
about 5 seconds. This button is used for performing operations in
low-light situations.
18 VIEW MODE: Select the screen size.
19 ENT: Jumps to a channel after selecting with the 0_9buttons.
20 FLASHBACK:Return to the previous channel or external input
mode.
21 CH / : Select the channel.
22 MUTE: Mute the sound.
23 MENU: Display the menu screen.
24 / / / ,ENTER: Select a desired item on the screen.
25 RETURN: Return to the previous menu screen.
26 FAVORITE CH
A, B, C, D: Select 4 preset favorite channels in 4 different
categories.
While watching, you can toggle the selected channels by pressing
A, B, C and D.
27 FAVORITE:Set the favorite channels.
28 CC: Display captions from a closed-caption source.
29 AV MODE: Select an audio or video setting.
(When the input source is TV, INPUT 1, 2 or 3: STANDARD,
MOVIE, GAME, USER, DYNAMIC (Fixed), DYNAMIC. When
the input source is INPUT 4, 5, 6 or 7: STANDARD, MOVIE,
GAME, PC, xvYCC (INPUT 4/5/6 only), USER, DYNAMIC (Fixed),
DYNAMIC)
Remote Control Unit
When using the remote control unit, point it at the TV.
32
1 16
5
6
4
8
19
17
18
20
21
7
22
10
9
23
11
1312
25
26
27
14
15 29
24
28
2 – 2
LC-C6554U
Removing the Stand
Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Appendix
Before attaching/detaching the stand
Before performing work, make sure to turn off the TV.
To attach the stand, perform the above steps in reverse order.
Unfasten the four screws used to secure the stand in place. Detach the stand from the TV.
1 2
Setting the TV on the Wall
CAUTION
This TV should be mounted on the wall only with the wall mount bracket. The use of other wall mount brackets
may result in an unstable installation and may cause serious injuries.
Installing the TV requires special skill that should only be performed by qualified service personnel. Customersshould not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mountingthat results in accident or injury.
Using an optional bracket to mount the TV
You can ask a qualified service professional about using an optional AN-65AG1 bracket to mount the TV on the wall.
Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
AN-65AG1 wall mount bracket.(See the bracket instructions for details.)
Vertical mounting Angular mounting
Detach the cable clamp on the rear of the TV when using the optional mount bracket.
To use this TV mounted on a wall, remove the covers at the 4 locations on the rear of the TV, and then use the screwssupplied with the wall mount bracket to secure the bracket to the rear of the TV.
About setting the TV angle
The "A" position is at thecenter of the display.Refer to the operationmanual of AN-65AG1 fordetails.
0o/ 5
o/ 10o
AN-65AG1
2 – 3
LC-C6554U
Troubleshooting
Possible Solution
Is the volume too low?Is "Variable" selected in "Output Select"?Have you pressed MUTE on the remote control unit?
Cautions regarding use in high and low temperature environments
Problem
No power
Unit cannot be operated.
Remote control unit does notoperate.
Picture is cut off/with sidebarscreen.
Strange color, light color, or colormisalignment
Power is suddenly turned off.
No picture
No sound
Check if you pressed TV POWER on the remote control unit.If the indicator on the TV does not light up, press POWER on the TV.Is the AC cord disconnected?Has the power been turned on?
External influences such as lightning, static electricity, may cause improper operation.In this case, operate the unit after first turning off the power of the TV or unpluggingthe AC cord and replugging it in after 1 or 2 minutes.
Is the FUNCTION set correctly? Set it to the TV setting position.Are batteries inserted with polarity ( , ) aligned?Are batteries worn out? (Replace with new batteries.)Are you using it under strong or fluorescent lighting?Is a fluorescent light illuminated near the remote control sensor?
Is the image position correct?Are screen mode adjustments such as picture size made correctly?
Adjust the picture tone.Is the room too bright? The picture may look dark in a room that is too bright.Check the input signal setting.
Is the sleep timer set?Check the power control settings.The unit's internal temperature has increased. Remove any objects blocking vent orclean.
Is connection to other components correct?Is correct input signal source selected after connection?Is the correct input selected?Is picture adjustment correct?Is "On" selected in "Audio Only"?Is a non-compatible signal being input?
When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.This is not a malfunction, and the unit will recover when the temperature returns to normal.Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near aheater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.Storage temperature: 4°F to 140°F ( 20°C to 60°C)
Troubleshooting-Digital Broadcasting
The error message about reception of broadcast
Failed to receive broadcast.
E203 Check the broadcast time in the program guide.
The example of an error messagedisplayed on a screen
No broadcast now.
Error code
E202
Possible Solution
Check the antenna cable. Check that the antenna is correctlysetup.
This is not a malfunction. This happens when the cabinet slightly expands andcontracts according to change in temperature. This does not affect the TV'sperformance.
The TV sometimes makes acracking sound.
Appendix
2 – 4
LC-C6554U
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal.
DDC is a registered trademark of Video Electronics Standards Association.VGA and XGA are registered trademarks of International Business Machines Corp.
PC
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
640 x 480
720 x 400
VGA
800 x 600SVGA
XGA 1024 x 768
WXGA 1360 x 768
70 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
O
O
O
O
O
O
O
O
O
O
O
64.0 kHzSXGA 1280 x 1024 60 Hz O
65.3 kHzSXGA+ 1400 x 1050 60 Hz O
75.0 kHzUXGA 1600 x 1200 60 Hz O
*
*
*
*
*These 4 formats are not supported by the analog RGB terminal.
PC Horizontal Frequency VESA StandardResolution Vertical Frequency
2 – 5
LC-C6554U
Menu Items
Some menu items may not be displayed depending on the selected input source.
Picture Menu
OPCBacklightContrastBrightnessColorTintSharpnessAdvanced
C.M.S.-HueC.M.S.-SaturationColor Temp.Active ContrastFine MotionI/P SettingFilm Mode3D-Y/CMonochromeRange of OPC
Reset
Audio Menu
TrebleBassBalanceSurroundBass EnhancerReset
Power Control Menu
No Signal OffNo Operation Off
Setup Menu
EZ SetupCH SetupAntenna Setup-DIGITALInput SkipInput LabelParental CTRLPositionLanguageReset
Option Menu
AQUOS LINK SetupAudio OnlyDigital Noise ReductionInput SelectOutput SelectColor SystemCaption SetupDigital Caption Info.Program Title DisplayFavorite CHGame Play TimeOperation Lock Out
Digital Setup Menu
Audio SetupIdentificationSoftware Update
On-Screen Display Menu
For TV/INPUT 1/2/3 Mode For HDMI/PC-IN Mode
Picture Menu
OPCBacklightContrastBrightnessColorTintSharpnessAdvanced
C.M.S.-HueC.M.S.-SaturationColor Temp.Active ContrastFine MotionI/P SettingFilm ModeMonochromeRange of OPC
Reset
Audio Menu
TrebleBassBalanceSurroundBass EnhancerReset
Power Control Menu
No Signal OffNo Operation Off
Setup Menu
Input SkipInput SignalAuto Sync.Input LabelFine Sync.PositionLanguageReset
Option Menu
AQUOS LINK SetupAudio OnlyDigital Noise ReductionHDMI SetupOutput SelectGame Play TimeOperation Lock Out
Digital Setup Menu
Software Update
2 – 6
LC-C6554U
3 – 1
LC-C6554U Service Manual CHAPTER 3. DIMENSIONS
[1] DIMENSIONS
Unit: inch (mm)
5629/64 (1433.5)
40(1016)
3711/ 64(944)
227/ 32
(72)
3023/32 (780)
6011/64 (1528)
37/8(98)
157/8(403)
61/32(153)
313/ 4
(806.5)
229/ 32(566)
1721/64(440)
2519/ 32(650)
1213/ 16
(325)
LC-C6554U
LC-C6554U Service Manual CHAPTER 4. REMOVING OF MAJOR PARTS[1] REMOVING OF MAJOR PARTS1. Remove the 6 black sheets.
2. Remove the 20 lock screws, 2 lock flat head screws, 2 lock screws, 2 lock screws, 4 lock clips and detach the Rear Cabinet.
3. Remove the 4 lock screws and detach the Stand.
CAUTION: In the case of assembly, the new sheet (PSPAKA237WJ00 and PSPAGA386WJ00) can be stuck on these screws.
Front Cabinet
Stand
Rear Cabinet
21
1
1
1
1
2
2
2
21
3Black Sheet
Black Sheet
Flat head screw
4 – 1
LC-C6554U
4. Remove the 4 lock screws and detach the Control Shield.5. Remove the 8 lock screws and detach the MAIN Shield.
6. Remove the 6 lock screws and detach the AV Shield.
4
5
6
AV Shield
MAIN Shield
Control Shield
4 – 2
LC-C6554U
7. Disconnect all the connectors from all the PWBs.8. Remove the Speaker (L) (R).
9. Remove the 2 lock screws, 3 lock screws and detach the Mini AV KEY Ass'y.
10.Remove the 2 lock screws, 2 lock screws and detach the Mini AV Shield, SIDE Unit, Mini AV KEY Cover from the Mini AV KEY Angle.
11.Remove the Operation Button and KEY Unit from the Mini AV KEY Cover.
9
10
11
8 8
10
9
Mini AV KEY Angle
Speaker (R) Speaker (L)
KEY Unit
Operation Button
Mini AV Shield
Mini AV KEY Cover
SIDE Unit
VD
US
HM
HMRA
KM
US
VD
MA
MA
SP
7
7
7
7
PE
PE
PD PD
LB
LP LA
LW
LW
LP/PL
PQPQ
PL
LC-2
KM
LA-2
PP1
PP2PP2
PP3
LC-1
LB
LA-1PP3
PP1
4 – 3
LC-C6554U
12.Remove the 8 lock screws, 1 lock screw and detach the SUB POWER Unit.13.Remove the 5 lock screws, 2 lock screws and detach the Tray Chassis, Terminal Bottom Angle.
14.Remove the 2 lock screws and detach the Barrier Sheet.
15.Remove the 16 lock screws, 4 lock screws and detach the Inverter Shield.
15
14
13
15
15 15
Barrier Sheet
Inverter Shield
Inverter Shield
Tray Chassis
Terminal Bottom Angle
1212
SUB POWER Unit
13
4 – 4
LC-C6554U
16.Remove the 2 lock screws, 4 lock Shafts and detach the Terminal Side Angle.17.Remove the 6 lock screws and detach the POWER Unit.
18.Remove the 5 lock screws and detach the TERMINAL Unit.
19.Remove the 3 lock screws and detach the Radiator Angle.
20.Remove the 2 lock screws and detach the MAIN Unit.
19
17
20
18
16
16
16
Terminal Side Angle
Radiator Angle
MAIN UnitTERMINAL Unit
POWER Unit
4 – 5
LC-C6554U
21.Remove the 2 lock screws and detach the LCD Panel Module.22.Remove the R/C, LED Unit.
23.Remove the 12 lock screws and detach the Panel Fix Angle-B.
24.Remove the 10 lock screws and detach the Panel Fix Angle-C.
25.Remove the 12 lock screws and detach the Panel Fix Angle.
23
24
21
22
25 24
21
25 23
Panel Fix
Angle-BPanel Fix
Angle-B
Panel Fix
Angle-C
Panel Fix Angle
Panel Fix Angle
Panel Fix
Angle-C
R/C, LED Unit
4 – 6
LC-C6554U
PartsGuidePARTS GUIDE
CONTENTS
Note:The reference numbers on the PWB are arranged in alphabetical order.
No. S38I1LCC6554U
LC-C6554UMODEL
[1] PRINTED WIRING BOARD ASSEMBLIES
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY.)
[3] DUNTKE208FM01 (TERMINAL Unit)
[4] DUNTKE264FM02 (R/C, LED Unit)
[5] DUNTKE558FM01 (MAIN Unit)
[6] NOTE (Conductive cloth tape)
[7] NOTE (Temperature-proof cover)
[8] CABINET AND MECHANICAL PARTS
[9] SUPPLIED ACCESSORIES
[10] PACKING PARTS (NOT REPLACEMENT ITEM)
[11] SERVICE JIG (USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace theseparts with specified ones for maintaining the safety and performance of the set.
This document has been published to be usedfor after sales service only.The contents are subject to change without notice.
LC-C6554UPRICE NEW PART
NO. PARTS CODE RANK MARK DELIVERY DESCRIPTION[1] PRINTED WIRING BOARD ASSEMBLIESN DUNTKE208FM01 BH X TERMINAL UnitN DUNTKE264FM02 AP X R/C, LED UnitN DUNTKE266FM02 AG N X KEY UnitN DUNTKE488FM01 BB N X SIDE UnitN DUNTKE558FM01 CB N X MAIN UnitN RDENCA246WJQZ BW N X SUB POWER UnitN RDENCA247WJQZ BT N X POWER Unit
[2] LCD PANEL (NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPEN-DENTLY.)
N R1LK645D3LZ40V ** N J 65" LCD Panel Module Unit
[3] DUNTKE208FM01 (TERMINAL Unit)Q501 VS2SA1162Y/-1Y AB N J Transistor, 2SA1162-Y(TE85L,F)/(T5L,F,T)Q503 VS2SA1162Y/-1Y AB N J Transistor, 2SA1162-Y(TE85L,F)/(T5L,F,T)Q505 VS2SA1162Y/-1Y AB N J Transistor, 2SA1162-Y(TE85L,F)/(T5L,F,T)Q509 VS2SA1162Y/-1Y AB N J Transistor, 2SA1162-Y(TE85L,F)/(T5L,F,T)Q510 VSKTC3875SG-1Y AB N J TransistorQ1101 VSKTC3875SG-1Y AB N J TransistorQ1102 VSKTC3875SG-1Y AB N J Transistor
[4] DUNTKE264FM02 (R/C, LED Unit)Q102 VSKTC3875SG-1Y AB J TransistorQ103 VSKTC3875SG-1Y AB J TransistorQ104 VSKTC3875SG-1Y AB J TransistorQ106 VSKTC3875SG-1Y AB J TransistorQ107 VSKTC3875SG-1Y AB J Transistor
[5] DUNTKE558FM01 (MAIN Unit)IC1403 VHIAK4682AE-1Y AP J IC, AK4682AEQIC1604 VHISII9185A-1Q AN N J IC, SII9185ACTUQ1307 VS2SA1162Y/-1Y AB N J Transistor, 2SA1162-Y(TE85L,F)/(T5L,F,T)Q2214 VSKTC3875SG-1Y AB N J TransistorQ9301 VS2SA1162Y/-1Y AB N J Transistor, 2SA1162-Y(TE85L,F)/(T5L,F,T)
2
LC-C6554U
[6] NOTE (Conductive cloth tape)
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[6] NOTE (Conductive cloth tape)1 PSLDMB255WJZZ AE N X Conductive Cloth Tape2 PSLDMB243WJZZ AF N X Conductive Cloth Tape3 PSLDMB254WJZZ AE N X Conductive Cloth Tape4 PSLDMB251WJZZ AH N X Conductive Cloth Tape5 ZSLCN-098P2KE BH J Bond (One 150g tube)
MAIN Unit
Radiator Angle
Terminal Bottom Angle
5
1
2
3
Apply bond to 1 location.
4
AttentionWhen peeling off the conductive cloth tape for repair, please use the NEW conductive clothtape. (When using the conductive cloth tape again, keep in mind the decrease in the adhesivepower of the conductive cloth tape. The purpose of using the NEW conductive cloth tape is toprevent the conductive cloth tape from peeling off.)
Added partsConductive Cloth Tape
Part code: PSLDMB255WJZZ Q'ty 1
Part code: PSLDMB243WJZZ Q'ty 1
Part code: PSLDMB254WJZZ Q'ty 1
Part code: PSLDMB251WJZZ Q'ty 1
Bond
Part code: ZSLCN-098P2KE (One 150g tube)
3
LC-C6554U
[7] NOTE (Temperature-proof cover)
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[7] NOTE (Temperature-proof cover)1 PSPAGA386WJ00 AB X Spacer, x52 PSPAKA237WJ00 AA X Spacer
AttentionPlease peel off the covers when you remove Rear Cabinet.
And please use the NEW cover when you install Rear Cabinet.
(When using the cover again, keep in mind the decrease in the adhesive power of the cover.
The purpose of using the NEW cover is to prevent the cover from peeling off.)
Added cover partsCover part code: PSPAGA386WJ00 Q'ty 5
Cover part code: PSPAKA237WJ00 Q'ty 1
2
1 1 1 1 1
4
LC-C6554U
[8] CABINET AND MECHANICAL PARTS
90
23
78
79
79-1
79-2 79-3
79-3
79-3
79-3
79-4
79-479-4
79-5
79-5
79-4
78
11-1
1-2
1-3
1-5
62
29
67
67
6767
67
67
67
67
67
57
45
47
46
44
56
67
20
22
23
23 23
27
27
27
23
23
23
23
23
22
22
2427
27
27
2525
52
25
25
2425
55
83
84
25
23
21
24
67
67
67
60
65
68
25
30
30
70
61
54
1-9 1-9
1-9
1-9
1-9
1-91-9
1-9
1-9
1-9
1-13
1-15
1-14
1-16
1-17
1-61-7
1-7
1-7
1-7
1-7
1-7
1-8
1-8
1-8
1-8
1-4
6
67
87
88
89
91
67
51
67
3943
43
36
49
48
67
82
67
53
67
33
32
19
15
35
13 40
11
6-1
6-2
4
2
2-1
2-2
76
76
76
69
71
10
12
64
64
3467
9
66
5
38
37
42
41
31
31
5-1
5-2
74
74
17
17
14
59
85
21
18
16
16
65
6565
65
65
6518
75
8
SUB POWER Unit
R/C, LED Unit
POWER Unit
SIDE Unit
TERMINAL Unit
MAIN Unit
63
2723
72
72
7
7
26
81
81
81 81
81
50
377
3-1
3-2
3-3
KEY Unit
24 23
80
80
58
28
73
73
86
22
1-10
1-11
1-111-12
1-12
1-12
5
LC-C6554U
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[8] CABINET AND MECHANICAL PARTS1 CCABAB845WJ32 CC N X Front Cabinet Ass'y
1-1 Not Available - - Front Cabinet1-2 Not Available - - Front Cover1-3 Not Available - - Badge, SHARP1-4 Not Available - - LED Cover1-5 HDECSA031WJ3A AP X Shine Trim1-6 HPNLSA156WJ3A BD X SP-Sheet1-7 Not Available - - Spacer, x61-8 Not Available - - Spacer, x41-9 Not Available - - Spacer, x101-10 Not Available - - Spacer1-11 Not Available - - Spacer, x21-12 Not Available - - Spacer, x31-13 TLABZA635WJZZ AC J E-STAR Label1-14 TLABZB934WJZZ AN X POP 1080P Label1-15 TLABZB965WJZZ AM N X POP Feature Label1-16 TLABZB966WJZZ AS N X POP Inch Label1-17 XJPSN30P08XS0 AA J Screw (for Front Cover), x32 CCABBB145WJ31 BQ X Rear Cabinet Ass'y
2-1 Not Available - N - Rear Cabinet2-2 Not Available - - Terminal Label Bottom3 CCOVAC862WJ31 AR N X Mini AV KEY Ass'y
3-1 Not Available - N - Mini AV KEY Cover3-2 HINDPC516WJSA AF X Mini AV Indicator3-3 Not Available - - Operation Button4 R1LK645D3LZ40V ** N J 65" LCD Panel Module Unit5 CCOVP2625TP01 AW N X Control Shield Ass'y
5-1 Not Available - N - Control Shield5-2 LHLDW1155CEZZ AD J Wire Holder, x26 CSLDMB158WJ31 AL N X MAIN Shield Ass'y
6-1 Not Available - N - MAIN Shield6-2 PSPAZB622WJZZ AB N X Spacer7 GCOVAC453WJKA AG X Bottom Cover, x28 GCOVAC466WJKB AY N X Support Front Cover9 GCOVAC467WJKB AY N X Support Rear Cover10 GCOVAC531WJUZ AC X VESA Cover, x411 HINDPC479WJSA AE X Terminal Label12 HINDPC877WJSA AE N X Model Label13 LANGKB194WJFW AG X Terminal Side Angle14 LANGKB195WJFW AH X Terminal Bottom Angle15 LANGKB231WJFW AN N X Mini AV Angle16 LANGKB232WJFW AM N X Panel Fix Angle, x217 LANGKB233WJN1 AN N X Panel Fix Angle-Top, x218 LANGKB234WJFW AN N X Panel Fix Angle-C, x219 LANGKB240WJFW AK N X Radiator Angle20 LCHSMA396WJ3W AX N X Main Chassis21 LHLDFA036WJKZ AB J Wire Holder, x422 LHLDW1155CEZZ AD J Wire Holder, x1523 LHLDWA124WJKZ AC J Wire Holder, x2324 LHLDWA143WJKZ AC J Wire Holder, x725 LHLDWA151WJKZ AB J Wire Holder, x926 PSPAKA237WJ00 AA X Spacer27 LHLDWA175WJUZ AC J Wire Holder, x1228 LHLDZA505WJKZ AC N X Wire Holder, x229 LX-BZA051WJF7 AB J Screw30 NSFTZ0134CEFW AD J Shaft, x431 PCOVP2615TPZZ AR N X Inverter Shield, x232 PRDARA509WJFW AF N X Heat Sink33 PRDARA510WJFW AR N X Heat Sink34 PSLDMB159WJ3W AK X AV Shield35 PSLDMB179WJ3W AD X Mini AV Shield36 PSPAZB313WJKZ AC J Spacer37 PSPAZB521WJKZ AE N X Cool Sheet, x338 PSPAZB523WJKZ AL N X Cool Sheet, x239 PSPAZB596WJKZ AN X Cool Sheet40 PZETKA273WJZZ AC N X Barrier Sheet41 PZETKA276WJZZ AF N X Insulator-A42 PZETKA277WJZZ AH N X Insulator-B43 QCNCMA275WJQZ AC N X Connector (MODEL SELECT), x244 QCNCMA673WJZZ AG J Connector45 QCNW-G123WJQZ AL N X Connecting Cord (PFC)46 QCNW-G124WJQZ AF N X Connecting Cord (PE)47 QCNW-G125WJQZ AH N X Connecting Cord (PD)48 QCNW-G126WJQZ AK N X Connecting Cord (LB)49 QCNW-G127WJQZ AU N X Connecting Cord (LA)50 QCNW-G130WJQZ AH N X Connecting Cord (KM)51 QCNW-G132WJPZ AM N X Connecting Cord (US)52 QCNW-G133WJQZ AY N X Connecting Cord (VD)53 QCNW-G134WJQZ AL N X Connecting Cord (RA)54 QCNW-G135WJQZ AK N X Connecting Cord (SP)55 QCNW-G159WJQZ AL N X Connecting Cord (PL/LP)56 QCNW-G275WJQZ AQ N X Connecting Cord (PP2/PP3)57 QCNW-G276WJQZ AH N X Connecting Cord (PQ)58 QCNW-G277WJQZ BA N X Connecting Cord (LW)59 QEARZ0057CEFW AB J Spring Conductor
6
LC-C6554UPRICE NEW PART
NO. PARTS CODE RANK MARK DELIVERY DESCRIPTION[9] SUPPLIED ACCESSORIES
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
60 QPWBHE305WJQZ BA N X Connecting Cord (HM)61 RSP-ZA347WJZZ AX X Speaker (L)62 RSP-ZA348WJZZ AX X Speaker (R)63 TCAUZA306WJZZ AD X Mercury Label64 RCORFA038WJZZ AH J Core, x265 XBBS840P08000 AB J Screw (for Angle), x3666 XBBS940P10000 AB J Screw (for Stand Bottom Cover), x267 XBPS730P06WS0 AA J Screw (for PWB), x20/(for Shield), x5868 XBPS830P06000 AA J Screw (for HDMI), x269 XBPS930P08JS0 AB J Screw (for AC Angle), x270 XBPS930P08WS0 AA X Screw (for HDMI Shield), x271 XBPS940P10JS0 AB J Screw (for CAB-Angle), x272 XBPS950P12KS0 AB X Screw (for Stand), x473 XBSS840P10000 AB J Flat Head Screw, x274 XEBS940P10000 AB J Screw (for CAB-Angle), x275 XEBS940P16000 AB J Screw (for Stand-F-Cover), x476 XEBS940P20000 AB J Screw (for CAB-B/Cover), x2277 XIPSN20P04000 AA J Screw (for MINI HDMI), x278 XJSS850P30000 AB J Screw (for Stand Ass'y), x879 CDAI-A368WJ32 BZ N X Stand Base Ass'y
79-1 Not Available - N - Stand Base79-2 LANGKB032WJZZ BN J Base Angle79-3 PSPAZB165WJZZ AC J Leg Cushion-A, x479-4 PSPAZB166WJZZ AB J Leg Cushion-B, x479-5 XEBS940P10000 AB J Screw, x1380 CDAI-A412WJ31 AZ X Stand Support Ass'y, x281 PSPAGA386WJ00 AB X Spacer, x582 PSLDMB255WJZZ AE N X Conductive Cloth Tape83 PSLDMB243WJZZ AF N X Conductive Cloth Tape84 PSLDMB254WJZZ AE N X Conductive Cloth Tape85 PSLDMB251WJZZ AH N X Conductive Cloth Tape86 Not Available - - Back Serial Label87 Not Available - N - Side Serial Label88 PZETKA283WJZZ AG N X Barrier Sheet89 PSPAZB622WJZZ AB X Spacer90 PSPAZB669WJZZ AB N X Spacer91 ZSLCN-098P2KE BH J Bond (One 150g tube)
[9] SUPPLIED ACCESSORIESX1 LHLDWA083WJ00 AD J Cable BandX2 LHLDWA173WJKZ AE N J Cable Clamp
! X3 QACCDA057WJPZ AW X AC CordX4 RRMCGA669WJSA AX X Remote Control UnitX5 TCADEA243WJZZ AD X Enquete CardX6 TCAUHA352WJZZ AD X Quick Set Up GuideX7 TCAUHA367WJZZ AD X Child Safety CardX8 Not Available - N - Extend WarrantyX9 TINS-D741WJZZ AL N X Operation ManualX10 Not Available - N - "AAA" Size Battery
[8] CABINET AND MECHANICAL PARTS
Operation Manual "AAA" Size Battery
Remote Control UnitX4Cable ClampX2Cable BandX1 AC CordX3
X9 X10
7
LC-C6554U
[10] PACKING PARTS (NOT REPLACEMENT ITEM)
S1
S2
S3
S4
S5
S8
S5S5
S5
S5S5
S6
S7
S5
8
LC-C6554U
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[10] PACKING PARTS (NOT REPLACEMENT ITEM)S1 SPAKCE296WJZZ - N - Packing Case (Main)S2 SPAKCD620WJZZ - - Packing Case (Bottom)S3 SPAKPA962WJZZ - - Wrapping Paper (Monitor)S4 SPAKPA993WJZZ - - Wrapping Paper (Stand)S5 SPAKXB605WJZZ - - Packing Add.S6 SSAKA0101GJZZ - - Polyethylene BagS7 SSAKAA032WJZZ - - Polyethylene BagS8 TLABKA009WJZZ - - No. Label
[11] SERVICE JIG (USE FOR SERVICING)N QCNW-E068WJQZ AS J Connecting Cord (6pin L=1000mm)N TERMINAL to POWER Unit (PE)N QCNW-F138WJQZ AP J Connecting Cord (4-2/2pin L=1000mm)N TERMINAL Unit (SP) to SPEAKERSN QCNW-G186WJQZ BL J Connecting Cord (41pin L=600mm)N MAIN to LCD CONTROL Unit (LW)N QCNW-G400WJQZ AV J Connecting Cord (12pin L=1000mm)N MAIN to POWER Unit (PD)N QCNW-G517WJQZ AW N J Connecting Cord (12-20/4pin L=1000mm)N MAIN to LCD CONTROL Unit/N POWER to LCD CONTROL Unit (LP/PL)N QPWBHE372WJQZ BE J Connecting Cord (21pin L=1000mm)N MAIN to SIDE Unit (HM)
9
LC-
SHARP CORPORATIONAV Systems GroupCS Promotion CenterYaita, Tochigi 329-2193, Japan
Jun. 2008TQ2517-S MI. KD
COPYRIGHT 2008 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.
C6554U