8/19/2019 Section III 1
http://slidepdf.com/reader/full/section-iii-1 1/6
For the beam and loading shown, determine:
(a) the location and magnitude of the maximum transverse shear force 'Vmax',
(b) the shear flow 'q' distribution due to 'Vmax',
(c) the 'x' coordinate of the shear center measured from the centroid,
(d) the maximun shear stress and its location on the cross section.
Stresses induced by the loads do not exceed the elastic limits of the material. Assume the transverse force
passes through the shear center of the beam at every cross section.
QUATIONS SED
OLUTION
(a) To find the maximum transvere shear, the shear at each section along the beam between sections A and
D must be found. This means that we need to draw the shear diagram. To do this we have to take the
following steps:
From the free body diagram, the reactions at A and D are
ion III.4 example 1 http://www.ae.msstate.edu/tupas/exp/A14.7_ex1.html
n 6 08.03.2016 16:11
8/19/2019 Section III 1
http://slidepdf.com/reader/full/section-iii-1 2/6
The transverse shear variation along the section with distributed force can be found by using the integral
equation
The resulting shear diagram shown below indicates that the maximum shear force is Vmax = 55.8 kN and
it occurs along portion CD.
ion III.4 example 1 http://www.ae.msstate.edu/tupas/exp/A14.7_ex1.html
n 6 08.03.2016 16:11
8/19/2019 Section III 1
http://slidepdf.com/reader/full/section-iii-1 3/6
(b) For the shear flow analysis we must consider a beam section with maximum shear force. In this case
any section along portion CD will satisfy this requirement. To obtain the shear flow, first draw the picture
of the cross section. Since the moment of inertia about the horizontal centroidal axis (perpendicular to the
direction of V) is already given, we can go directly to the moment of area (Q) calculation. Begin at the
free end of the top right flange where we know the shear flow is zero, and consider a portion of length s
as shown in the figure below.
Write the equation for the shear flow in terms of the moment of area of the portion of length s.
ion III.4 example 1 http://www.ae.msstate.edu/tupas/exp/A14.7_ex1.html
n 6 08.03.2016 16:11
8/19/2019 Section III 1
http://slidepdf.com/reader/full/section-iii-1 4/6
Notice that the moment of inertia is that of the entire I cross section about the horizontal centroidal axis,
which is perpendicular to the direction of V.
Due to symmetry about the vertical centroidal axis, the shear flow in the top left flange will be the sameas the flow in the top right (same magnitude, opposite direction). Also due to symmetry about the
horizontal centroidal axis, the shear flow in bottom flanges will be the same as the ones on top (same
magnitude, opposite direction).
In the web, the shear flow doesn't start from zero, like it did in the flanges. This is because the starting
point of the web is a junction and not a free end. The starting shear flow for the web is shown in the figure
below.
Using the fluid flow analogy the flow coming into the web-flange junction from flanges must leave the
junction through the web.
To determine the shear flow variation along the web, isolate a section of length w along the web as shown
in the figure below.
ion III.4 example 1 http://www.ae.msstate.edu/tupas/exp/A14.7_ex1.html
n 6 08.03.2016 16:11
8/19/2019 Section III 1
http://slidepdf.com/reader/full/section-iii-1 5/6
Write the shear flow equation by writing the starting value which is 128.96 kN/m, and adding to it the
contribution of the web. V/I ratio stays the same (as it should), and all that remains to be calculated is the
moment of area of length w along the web.
The complete shear flow diagram is shown below. The shear force in the web is found by calculating the
area under the q diagram. This gives a value of 54.626 kN which represents approximately 98% of the
total shear force which is 55.8 kN. The rest of it (not shown), as explained before, will be carried by the
top and bottom flanges.
ion III.4 example 1 http://www.ae.msstate.edu/tupas/exp/A14.7_ex1.html
n 6 08.03.2016 16:11
8/19/2019 Section III 1
http://slidepdf.com/reader/full/section-iii-1 6/6
(c) Since this is a doubly symmetric cross section, the shear center is located at the intersection of the axes
of symmetry which is the centroid.
(d) The maximum shear stress will occur at the point on the cross section where the ratio (q/t) is
maximum. In this problem that point is located on the neutral axis.
In summary, the maximum shear stress in the flange is 6.829 MPa and occurs at the intersection of the
flange and the web (i.e., s = 61 mm). The minimum shear stress in the web is 21.493 MPa and the
maximum shear stress is 30.511 MPa.
To Next Example
To Section III.4
To Index Page of Transverse Shear Loading of Open Sections
ion III.4 example 1 http://www.ae.msstate.edu/tupas/exp/A14.7_ex1.html