CA
TA
LO
G
P28-S
7-C
over.
pub
The information contained herein is copyright protected and is the sole property of DTL Technologies, LP, and may not be reproduced without expressed written permission, it may be changed without notice. All rights reserved, DTL Technologies, LP. Houston, Texas 713-932-9119
RIGID CONDUIT MANIFOLDS, FAIL-SAFE ASSIST CIRCUITS, EDS SYSTEMS, MULTI-PILOT CONNECTORS
DTL can manufacture manifolds, control systems, and add-on circuit hardware. Accumulator manifolds, supply headers, and special control circuits such as Choke and Kill Fail-Safe circuits and Rigid Conduit Manifolds have all been man-ufactured by DTL Technologies.
SSY
ST
EM
SY
ST
EM
S /
M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
CA
TA
LO
G
P30-S
7.p
ub
The information contained herein is copyright protected and is the sole property of DTL Technologies, LP, and may not be reproduced without expressed written permission, it may be changed without notice. All rights reserved, DTL Technologies, LP. Houston, Texas 713-932-9119
RIGID CONDUIT VALVE ASSEMBLY
This Multi-Valve Assembly was created to operate as a rigid conduit manifold. This configuration will allow control of the rigid conduit supply to the yellow and blue pods. This design improvement was used to convert the main con-trol valves from slide valves to SPMs. Secondary focus was to reduce plumb-ing clutter on the stack by condensing the circuit into a modular package. Features include conduit dump, filter assembly, and pilot controls to flow sup-ply and POD pressure dump.
SSY
ST
EM
SY
ST
EM
S /
M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
CA
TA
LO
G
P31-S
7.p
ub
The information contained herein is copyright protected and is the sole property of DTL Technologies, LP, and may not be reproduced without expressed written permission, it may be changed without notice. All rights reserved, DTL Technologies, LP. Houston, Texas 713-932-9119
RIGID CONDUIT VALVE ASSEMBLY
This Rigid Conduit Assembly is designed to be mounted on a flat surface / plate. The bolt pattern for mounting and schematic diagram is shown in the figure below.
SPECIFICATIONS
Maximum working pressure: 3000 PSI
Maximum proof pressure: 4,500 PSI
Assembly weight: 425 lbs
Conduit Manifold Inlet & Outlet Connections : 1-1/2” Code 62 Seal-
Sub W/Adaptors to JIC as shown.
Pilot connections: 1/4 NPT
Built-In filter: 40 Micron
SSY
ST
EM
SY
ST
EM
S /
M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
CA
TA
LO
G
P32-S
7.p
ub
The information contained herein is copyright protected and is the sole property of DTL Technologies, LP, and may not be reproduced without expressed written permission, it may be changed without notice. All rights reserved, DTL Technologies, LP. Houston, Texas 713-932-9119
FAIL-SAFE ASSIST CIRCUITS
Fail-Safe Assist Circuits are
added to Choke and Kill valves
to assist in positive closure of
these types of valves, which
were originally designed with a
spring-to-close actuator. The
fail-safe circuit supply pressure
is captured in an accumulator
from the pilot line when the
choke or kill valve is hydrau-
lically opened. When the pilot
signal is removed, the accumu-
lated pressure is released to
close the valve along with the
spring actuator. An orifice can
be installed between the two
control valves to sequence the
valves when both pilots are re-
leased simultaneously.
SSY
ST
EM
SY
ST
EM
S /
M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
CA
TA
LO
G
P33-S
7.p
ub
The information contained herein is copyright protected and is the sole property of DTL Technologies, LP, and may not be reproduced without expressed written permission, it may be changed without notice. All rights reserved, DTL Technologies, LP. Houston, Texas 713-932-9119
SKID-MOUNTED REGULATOR / SPM
SPECIFICATIONS
Maximum working pressure: 5,000 PSI Regulator outlet adjustable to: 1,000 - 4,500 PSI Assembly weight: 175 lbs Regulator & SPM manifold inlet & outlet connections: 1” Code 62 Seal-Sub
This Multi-Valve Assembly was designed to add a 3000 PSI circuit from a 5K PSI supply manifold. The configuration will allow reduction of pressure from the 5000 PSI supply to 3000 PSI downstream from the regulator. An SPM control valve (N.C. 3W-2P) was used to control supply to the new circuit.
SSY
ST
EM
SY
ST
EM
S /
M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS
SS
YS
TE
MS
YS
TE
MS
/ M/ M
AN
IFO
LD
SA
NIF
OL
DS