Transcript
Page 1: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

2600/2700 Series General Purpose 1/4-Turns.

A wide choice of general purpose studs and receptaclesare available with this series. Certain 2600 and 2700series 1/4-turn fasteners are qualified to MIL-F-5591*specifications. Also included are receptacles for fastinstallation, or for ultrasonic installation. Integral studcup protects top panel surface from abrasion.

2600 Series.Plus flush head styles and solidretaining rings.

2700 Series.Flush head styles and splitretaining ring.

Retaining rings are usedwith stud lengths -5 and greater,except for snap-in versions whichdo not require retaining rings.

stnetnoCnoitceS .oNegaP

sdutSseireS0062 72-A-62-A

sdutSseireS0072 82-A

sgniRgniniateR 82-A

selcatpeceR 23-A-92-A

dnanoitaraperPlenaPdutSataDnoitallatsnI 33-A

gniRgniniateRdnaelcatpeceRataDnoitallatsnI 53-A-43-A

Specifications:Ultimate tensile strength: 300 lbs.Working strength: 200 lbs

*Meets the design, physical andperformance requirements of MIL-F-5591. However, full mechanicalproperties testing may not beperformed on each production lot.

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

A-22

beckedc
Text Box
Page 2: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

Ordering InformationNote: Receptacles determine which stud is selected,therefore, an overview is included here.

To Select Stud Part Number.

1. Stud part number varies with receptacle used. Thereceptacle must be chosen before selecting stud partnumber. See receptacle detail on Pages A-27 through A-30.

2. Determine “G” thickness as shown in drawings below.

Notes:a) Increase “G” to allow for thickness of paint or other

finishes and for the compressed thickness of any gasket.b) ”G” must be increased for the following “special”

conditions:

3. Locate “G” total thickness in the tables with each stud.4. Then find the corresponding stud part number in the columndesignated for the selected receptacle.

Example 1.Stud Assembly Used: 2700-[ ]“G” Total Thickness = .275 inchReceptacle Used: 212-12ADStud Dash Number From Table: -9Complete Part Number: 2700-9Example 2.Stud Assembly Used: 2600-[ ]“G” Total Thickness =.163 inchReceptacle Used: 212-12BRRequired Calculation: “G” + .038 = .163 + .038 = .201Stud Dash Number Selected From Table: -6Complete Part Number: 2600-6S

Important Note: If the total thickness“G” is very near the top of thethickness range, selection of the nextgreater dash number is recommended.For the other materials and for “G”thickness greater than those tabulated,contact the Camloc Products Division.

noitidnoC”laicepS“ ssenkcihT”G“esaercnIselcatpecerseireSB21-212

dellatsni hcni830.ddA

elcatpecergnitnuomtnorFdellatsni)AA1-1-14R62N/P(

rofhcni220.wollAedispotselcatpecer

noisurtorp

elcatpecergnitnuomraeRdellatsni)AA1-1-54R62N/P(

rofhcni810.wollAedispotelcatpecer

noisurtorp)11R99N/P(elcatpecerno-pilC

dellatsnitcartbusdna090.ddA

srebmunhsad7gnitnuomelohelgniS

dna01R99.soN/P(elcatpecer)01E99

hcni020.ddA

stresneeK.seireS2QNKdellatsni hcni030.ddA

noitceleSrebmuNhsaDdutS

”G“latoT

ssenkcihT

selcatpeceR

1R622R62

5R6221-213

rehtOllAtoNs’N/P

detalubaT920.-020. – – –950.-030. *2- – *1-970.-060. – – –980.-060. 3- – *2-980.-080. – – –911.-090. 4- – 3-941.-021. 5- – 4-971.-051. 6- – 5-902.-081. 7- – 6-932.-012. 8- – 7-962.-042. 9- – 8-992.-072. 01- – 9-923.-003. 11- – 01-953.-033. 21- – 11-983.-063. 31- – 21-914.-093. 41- *1- 31-944.-024. 51- *2- 41-974.-054. 61- 3- 51-905.-084. 71- 4- 61-935.-015. 81- 5- 71-965.-045. 91- 6- 81-995.-075. 02- 7- 91-926.-006. 12- 8- 02-956.-036. 22- 9- 12-986.-066. 32- 01- 22-917.-096. 42- 11- 32-947.-027. 52- 21- 42-977.-057. 62- 31- 52-908.-087. 72- 41- 62-938.-018. 82- 51- 72-968.-048. 92- 61- 82-998.-078. 03- 71- 92-929.-009. 13- 81- 03-959.-039. 23- 91- 13-989.-069. 33- 02- 23-910.1.-099. 43- 12- 33-940.1-020.1 53- 22- 43-970.1-050.1 63- 32- 53-901.1-080.1 73- 42- 63-931.1-011.1 83- 52- 73-961.1-041.1 93- 62- 83-991.1-071.1 04- 72- 93-922.1-002.1 14- 82- 04-952.1-032.1 24- 92- 14-982.1-062.1 34- 03- 24-913.1-092.1 44- 13- 34-943.1-023.1 54- 23- 44-973.1-053.1 64- 33- 54-904.1-083.1 74- 43- 64-934.1-014.1 84- 53- 74-964.1-044.1 94- 63- 84-994.1-074.1 05- 73- 94-925.1-005.1 – 83- 05-955.1-035.1 – 93- –985.1-065.1 – 04- –916.1-095.1 – 14- –946.1-026.1 – 24- –976.1-056.1 – 34- –907.1-086.1 – 44- –937.1-017.1 – 54- –967.1-047.1 – 64- –997.1-077.1 – 74- –928.1-008.1 – 84- –958.1-038.1 – 94- –988.1-068.1 – 05- –

*2700 Series studs with -1 or -2 lengths require special part numbers;contact Camloc Products Division.

A-23

A

beckedc
Text Box
Page 3: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

2600/2700 Series. General Purpose Stud Assemblies.Features: • Wide variety of studs and receptacles offered as standards. • Integral stud cup protects toppanel surface from abrasion. • Sealed versions available (not shown).

Notes: 1. For Beryllium Copper material specify Part No. 26S26-[ ]B.2. For Slotted Knob style in Steel (Cadmium Plated) use Part No. 26S34-[ ]D.

Maximum Service Temperature: Stainless Steel—700°F.; Plastic Knobs—300°F.; all others—450°F.

*Stud lenghts to -15.

*Stud lenghts to -15.

daeHdelrunK gniWgnidloF eldnaHliaBgnidloFxeHlanretxEelytSnI-panS

lairetaM .oNtraP .oNtraP .oNtraP .oNtraPleetSsselniatS - - B][-22S62 -

)detalPmuimdaC(leetS AK][-0062 ][-A-31S62 ][-22S62 -

,detalPmuimdaC(leetS)etamorhCraelC - ][-B-31S62 - -

raelC,detalPcniZ(leetS)etamorhC - - - A1-]*[-531S62

Note: Part numbers shownare basic part numbersonly. See orderinginformation on Page A-23for required dash numbers.

sseceRdettolS sseceRssorC 0004SANrepelytSsseceR

lairetaM 1.oNtraP .oNtraP .oNtraP .oNtraP .oNtraPleetSsselniatS S][-0062 - ][-15S62 - BB3-][-28S62

leetSsselniatS)citengaM-noN( ][-62S62 - - - -

)detalPmuimdaC(leetS ][-0062 - ][-8S62 - AA3-][-28S62

,detalPmuimdaC(leetS)etamorhCraelC - - - - -

)detalPlekciN(leetS ][-24S62 - ][-93S62 - -)lemanEkcalBnitaS(leetS B][-0062 - B][-8S62 - -

)detalPemorhC(leetS ][-83S62 - - - -)detalPcniZ(leetS - AA1-]*[-301S62 - AA1-]*[-701S62 -

etahpsohPkcalB(leetS)detaoC - BA1-]*[-301S62 - BA1-]*[-701S62 -

)detavissaP(SERC682A - - B][-15S62 -

2600 Studscontinued

A-24

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

beckedc
Text Box
beckedc
Text Box
Minimum Preload - 15 LBS
Page 4: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

Specifications:Ultimate tensile strength: 300 lbs. Working strength: 200 lbs.Stud grip increments: .030 inch. For other styles, materials orfinishes, please contact Camloc Products Division.

Plastic Knob Styles

Basic Part Nos.

*Stud lengths to -15.

)detalPcniZ(leetS:lairetaMknahS

kcalB deR yerG egieB

bonK-T AD1-][-89S62 BD1-][-89S62 CD1-][-89S62 DD1-]*[-89S62

)nI-panS(bonK-T AA1-]*[-901S62 BA1-]*[-901S62 CA1-]*[-901S62 DA1-]*[-901S62

bonKdelrunK AD1-][-99S62 BD1-][-99S62 CD1-][-99S62 -

)nI-panS(bonKdelrunK AA1-]*[-011S62 BA1-]*[-011S62 CA1-]*[-011S62 -

tekcoSxeH gniWdexiF bonKdelrunK daeHdelrunK

.oNtraP .oNtraP .oNtraP .oNtraP .oNtraP- - WS][-0062 - -- - ][-63S62 A][-62S62 -

AA1-][-79S62 - W][-0062 - K][-0062- - - B][-43S62 ][-53S62- - ][-73S62 - ][-04S62- - - A][-43S62 -- - - ][-43S62 -- AA1-]*[-801S62 - - -- BA1-]*[-801S62 - - -- - - - -

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

A-25

beckedc
Text Box
Page 5: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

2600/2700 Series. General Purpose Stud Assemblies.

Maximum Service T emperatures: Stainless Steel—700°F; Steel and Bryllium Copper—450°F .

Retaining Rings (for 2600/2700 Series)

Solid rings are used to hold stud assembliesstationary to the top panel.

Split ring allows stud assemblies to move freelywithin the top panel.

Notes: 1. Order separately.2. Retaining rings are required for stud length dash numbers “5”

and greater.3. Studs with smaller dash numbers are self-captivating and

retaining rings are not used.4. Please see page A-33 for installation procedures for split rings.

Note: Part numbers shownare basic part numbersonly. See orderinginformation on Page A-23for required dashnumbers

sseceRdettolS sseceRssorC sesseceR”tnatsiseRrepmaT“

lairetaM .oNtraP .oNtraP .oNtraP .oNtraP .oNtraPleetSsselniatS S][-0072 - - - -

leetS)detalPmuimdaC(

][-0072 CA1-]*[-71S72 ][-3S72 CA1-]*[-81S72 AA1-][-8S728701SANreP

- - - - AA3-][-8S720004SANreP

- - - - AA4-][-8S72sseceReuqroT-iH

leetS)lemanEkcalBnitaS( A][-0072 - A][-3S72 - -

leetS)detalPemorhC( B][-0072 BA1-]*[-71S72 - BA1-]*[-81S72 -

reppoCmuillyreB)citengaM-noN( BB1-][-21S72 - - - -

leetS)detalPcniZ( - AA1-]*[-71S72 - AA1-]*[-81S72 -

Retaining Ring Installation Tool T98-1(For use with Solid Rings Only)

esUroFeriuqeRgniRdiloSslenaPdelpmiDhtiW

)ylbmessAdutSseireS0072(gniRdiloS

esopruPlareneGgniRtilpS

esopruPlareneG)hsiniF(lairetaMleetSsselniatS 7-WL-0062 - WS-0062

)muimdaC(leetSdetalPortcelE *WL-0062 1-5S72 2WS-0062

detalPlacinahceM MWL-0062 M1-5S72 -)cniZ(leetS

detalPortcelE *1A10-01W99 - 1A10-11W99detalPlacinahceM 1M10-01W99 - -

repthgieWseceip001 .sbl40.0 .sbl40.0 .sbl30.0

noitallatsnIderiuqeRlooT 1-89T 1-89T

sreilpesoneldeenesUnoitamrofnieromroF

33-AegaPees

* N o t r e c o m m e n d e d f o r u s e w i t h S t u d E j e c t o r S p r i n g s . U s e 2 6 0 0 - S W .M a x i m u m S e r v i c e Te m p e r a t u r e s : S t a i n l e s s S t e e l — 7 0 0 ° F. ; a l l o t h e r s — 4 5 0 ° F.

A-26

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

beckedc
Text Box
Page 6: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

Stud Ejector Springs

Provides for retraction of stud assembly to allowopening and closing of equipment without thepossibility of jamming or damage. Select theejector spring corresponding to stud assemblyseries selected. See table for part numbers.

Receptacles for Fast Installation

Front Mounting VersionPart Number: 26R41-1-1AA

Rear Mounting VersionPart Number: 26R45-1-1AA

MATERIAL: cage: carbon steel, (zinc plated); receptacleelement: zinc diecasting, (zinc plated).

Clip-on VersionPart Number: 99R11-1-1AA

MATERIAL: carbon steel clip (zinc plated); zinc alloy insert(zinc plated); steel retaining ring.

Ultrasonicaly Installed VersionInstalls into Thermoplastics.

MATERIAL: zinc alloy (zinc plated).

Note: When selecting studs for short version (26R48-2-1AA)receptacle, subtract .200 in. from total grip.

ELYTS .ONTRAPAMID

GNOL AA1-1-84R62 005.TROHS AA1-2-84R62 03.

seireS0062htiwesUseilbmessAdutS

seireS0072htiwesUseilbmessAdutS

retemaiDX ).feR(834. ).feR(005.seloHteviRnialP SE-0062 ----

seloHteviRdelpmiD DSE-0062 DSE-0072seceip001repthgieW .sbl138.0 .sbl149.0

hsiniFdnalairetaM )etamorhcdlogdetalpmuimdaC(leetSgnirpSecivreSmumixaM

erutarepmeT 054 ° .F 054 ° .F

Notes: 1. Thru hole in Ejector Spring Part Number 2700-ESD is formed to al low 2700 Series Stud Assemblies to seat f lush to topsurface of Ejector Spring.

2. Add .018 to total “G” thickness when using these parts.

A-27

A

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

beckedc
Text Box
beckedc
Text Box
Page 7: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

Receptacles. (For use with 2600/2700 and 26F Series Stud Assemblies).

Standard Mounting Versions

htdiWworraNdetaluspacnE

gnilaeSroF1etoNeeS

lairetaM .oNtraP .xaM.pmeT

teviRseloH

thgieW001rep(

).scp).sbl(

.oNtraP .xaM.pmeT

teviRseloH

thgieW001rep(

).scp).sbl(

.oNtraP .xaM.pmeT

teviRseloH

thgieW001rep(

).scp).sbl(

leetSsselniatS--gaM-noN()detavissaP

S21-212 057 ° .F nialP 50.1 −− −− −− −− 1-81R62 057 ° .F nialP 36.1

DS21-212 057 ° .F knuS’C 00.1 −− −− −− −− 2-81R62 057 ° .F knuS’C 36.1eznorBnociliS

)detalPmuimdaC(21-212 054 ° .F nialP 12.1 N21-212 .F°054 nialP 71.1 1-61R62 003 ° .F nialP 36.1D21-212 054 ° .F knuS’C 61.1 DN21-212 .F°054 knuS’C 21.1 2-61R62 003 ° .F knuS’C 36.1

eznorBnociliS)detalPlekciN( 92-212 054 ° .F nialP 12.1 −− −− −− −− −− −− −− −−

cniZ)detalPcniZ( E21-212 003 ° .F nialP 12.1 −− −− −− −− −− −− −− −−

yollAmunimulA)dezidonA(

A21-212 053 ° .F nialP 04. −− −− −− −− −− −− −− −−DA21-212 053 ° .F knuS’C 83. −− −− −− −− −− −− −− −−

yollAmmunimulA)dezidonAdraH( H-A21-212 053 ° .F nialP 04. −− −− −− −− −− −− −− −−

Notes: 1. Encapsulated receptacle may be sealed against air, water, and dust by using 3M brand EC847 or a silicon adhesive sealant.2. Use of 312-12 low profile receptacles is restricted to applications with total “G” thickness of .390 inch and greater. Please see illustration

Page A-23 for definition of “G.”

thgiewthgiLeliforPwoL

)2etoNees(egasudetcirtseR smihS

lairetaM traP.oN

.xaM.pmeT

teviRseloH

traP.oN

.xaM.pmeT

teviRseloH

traP.oN

.xaM.pmeT

teviRseloH

leetSsselniatS

−− −− −− A21-213 057 ° .F nialP 431.821. .aid −− −− −−

−− −− −− S21-213 057 ° .F nialP 201.690. .aid −− −− −−

−− −− −− SW21-213 057 ° .F noN)sbiNdleW( −− −− −−

leetS)detalPmuimdaC(

BB1-6R62 054 ° .F nialP 21-213 054 ° .F nialP 201.690. .aid −− −− −−

BB4-6R62 054 ° .F knuS’C −− −− −− −− −− −−BB6-6R62

worraN()htdiW

054 ° .F nialP −− −− −− −− −− −−

yollAmunimulA)dezidonA(

−− −− −− −− −− −− 1-8R62 053 ° .F nialP−− −− −− −− −− −− 2-8R62 053 ° .F knuS’C

A-28

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

beckedc
Text Box
Page 8: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

Floating Version(Float = ±.030)

Corner Mounting Versions

Side Mounting Versions

Receptacles (continued)

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

thgiewthgiL

lairetaM traP.oN

.xaM.pmeT

traP.oN

.xaM.pmeT

traP.oN

.xaM.pmeT

traP.oN

.xaM.pmeT

leetS)detalPmuimdaC( — — — — 1-5R62 .F°054 — —

:tnemelEelcatpeceReznorBnociliS — — — — — — R-B21-212 .F°054

:tekcarBleetSsselniatS

roFB21-212-hcattAgnidleW

teviron(tnem)seloh

.F°054

yollAmunimulA)dezidonA( 1-1R62 .F°053 — — — — — —

yollAmunimulA)dezidonAdraH( 5-1R62 .F°053 1-3R62 .F°053 — — — —

lairetaM traP.oN

.xaM.pmeT

yollAmunimulA)dezidonA 1-2R62 .F°053

yollAmunimulA)dezidonAdraH( 5-2R62 .F°053

lairetaM traP.oN

.xaM.pmeT

:tnemelEtresnI761AMTSArepSERC

AA1-1-15R62 –:egaC

347AMTSArepSERC

A-29

A

beckedc
Text Box
beckedc
Text Box
beckedc
Text Box
beckedc
Text Box
Page 9: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

srebmuNtraPllirDpaT

.aiDllirDpaT

htpeD.niM

eroB’CsnoisnemiD

paTeziS

.niMlluFdaerhThtpeD

llatsnIslooT

ataDlavomeR

sselniatSleetS leetS llirD

eziSllirDhtpeD

S2-QNK — 014.504. 756. x.aiD005.

htpeD530.-550.02-61/7B2-FNU 03.

A2-QTdnaB2-QT

23/11 23/5— 2-QNK

Removal: In the unlikely event it becomes necessary to remove the KEENSERT Insert, simply drill to theindicated depth, deflect the locking kees inward and break them off. Then remove insert with an E-Z outtype tool. An identical insert can now be installed in the original hole without rework.

Single Hole Mounting ReceptaclesDesigned to allow mounting in dimpled or drilledand countersink holes. Can also be installed intapped holes. Blind end version is ideal whenreceptacle is to be used with structural foams.

Installation Options

rebmuNtraP /lairetaMhsiniF

.xaM.pmeT

thgieWrep(

).scp001).sbl(

1A10-01R99htiwcniZ

gnitalPcniZ

.F°003 40.110-01E99

detaluspacnEnoisreV

.F°003 01.1

1A10-01N99lateM-teehS

noisreV

leetS,detalPcniZ(

)etamorhCraelC.F°003 31.0

CA1-01R51noisreVdiloS

leetS,detalPmuimdaC(

)etamorhCraelC.F°003 32.0

Rec

epta

cles

Nut

s

Special Purpose Receptacles

KEENSERTS® InsertFor use in aluminum and magnesium castings and other thick materials.

Installation:

Drill, counterbore, and then tap thread in structureusing data from table below . Turn KEENSERTS Insertinto tapped hole using installation tool P/N TQ-2Afor positive depth control. Drive locking kees downinto the tapped threads of the structure using toolP/N TQ-2B. This provides a positive mechanicallock against rotation.

Installation Data

Dimpled Panel

Optional Hole Shapes

Drill .406 Dia. hole, then form to shape illustrated.

Notes: 1. “D” and double “D” shaped holes provide a positive stopagainst rotation.

2. When using round mounting holes, retainer nut must besecurely tightened to prevent rotation of receptacles.

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

A-30

Drilled Panel

beckedc
Text Box
Page 10: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

P .feR.aiDX560.ot030. 752.521.ot660. 182.

2600 Series Protruding Head Studs

Determine panel thickness “P” and form throughhole to corresponding “X” diameter . Note: Panelswith thicknesses greater than .125 inch must be backcounterbored to a concentric .375 inch diameterwith a remaining maximum material thickness of.125 inch. Use split style retaining rings with backcounterbore.

Float:To provide float for stud assembly , increase “X”diamater to .312 inch. This hole diameter allows “P”thickness to be increased to .187 inch without backcounterboring. Larger hole requires used of solidretaining ring, P/N 2600-L W.

2600/2700 Series Snap-in Studs

Form through hole to .260-.256 diameter . Note:Panels with panel thicknesses greater than .078 mustbe back counterbored to a concentric .375" diameterwith a remaining maximum thickness of .078.

2700 Series Flush Mounting StudsInstallation in “Thin” PanelFor panel thicknesses “P” up to .072 inch maximum,form through hole to .213 diameter . Then dimpleusing tools shown below . Through hole afterdimpling to be .257; ream if necessary .

Installation in “Thick” PanelFor panel thickness “P” larger than .072 inch, formthrough hole to .257 diameter and 100° C’Sink to adiameter of .437.Panels with thicknesses greater than .140 inch mustbe back counterbored to a concentric .375 inchdiameter with a remaining material thickness of .140 inch maximum.Use split style ring with back counterbore.

Note: If float is required, all dash lengths require retaining rings as described in “Float” above.

Installing Stud Into PanelCompress stud assembly spring using Camloc pliers, P/N 4P3, as shown.Insert stud into panel and release when cross pin clears panel.

Typical Installations

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

A-31

A

Panel Preparation and Installation Data

beckedc
Text Box
Page 11: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

elcatpeceR .aiD”X“ kniS’C *waSeloHdetaluspacnE

,1-61R62s’N/P2-61R62

734. .aiD005x°09 734-SH

dradnatSrehtOllAselcatpeceRtnuoM 005. deriuqeRenoN

005-SHro

005-SH

Receptacle Installation Data

Standard Mounting Versions1. Drill #30 (.1285) dia. pilot hole.2. Drill holes for .093 dia. rivets using drill jigP/N T12 or equivalent.3. Enlarge pilot hole to X diameter and countersinkif required.4. Rivet receptacle in place.Important Note: 1100 F aluminum alloy rivets should be usedwith aluminum receptacles.

Typical Installation(Thin panels may be dimpled)

* Hole Saws are available as a convenience in selected sizes.

Drill Jig T12Provides convenient means for accurately locating rivet holeswith .750 inch spacing relative to stud mounting hole.

Side Mounting Versions26R1 and 26R3 Aluminum ReceptaclesImportant Note: 1100F aluminum alloy rivets should be usedwith aluminum receptacles.

26R5 Lightweight Receptacle

212-12B Silicon Bronze Receptacles

26R2 Aluminum Corner Mounting Receptacle

Important Note: 1100 F aluminum alloy rivets should beused with aluminum receptacles.

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

A-32

Hole SawsAccurately sizes mounting holesAvailble with either a smooth or drill bit pilot.

beckedc
Text Box
Page 12: QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES 2600/2700 Series General Purpose … · 2013-08-03 · 2600/2700 Series General Purpose 1/4-Turns. A wide choice of general purpose

paGetanimilEoT ssenkcihTGesaercnIerobretnuocallirdrodloM.nimhcni095.,emarfotni

,peedhcni020.ybretemaidsihtotelcatpecerllatsnidna

*.htped

.hcni020.ddA

foedisrednuerobretnuoC.nimhcni574.lenap

.peedhcni020.ybretemaidderiuqeresaercnioN

Front Mount VersionPart Number 26R41-1-1AANo riveting or special tools required.

HOLE PREPARATION

HOLE PREPARATION

Notes:1. To be used as a guide only. To obtain optimum performance,final hole size should be determined for particular application.2. See Page A-23 for “G” total thickness for stud length selection.When using 2600-LW or 99W10 type solid ring retainers, a .018inch gap between panel and frame will occur. Increase “G” totalthickness by .018 inch. To eliminate gap, refer to table for options.

Retaining Ring Installation1. To install, place retaining ring on stud with slotaligned over left side of cross pin as shown on figure 1.2. Snap retaining ring under cross pin using needlenose pliers, then rotate retaining ring 180° until ring isover right side of cross pin as shown on figures 2 and 3.3. To complete installation, snap retaining ring over theright side of cross pin.4. Completed installation is shown in figure 4.

Retaining Ring Installation Tool T98-1(For use with Solid Rings Only)

Rear Mount VersionPart Number 26R45-1-1AANo riveting or special tools required.

*Welding horn must be 095.065.

diameter.

Ultrasonically Installed V ersionsPart Number 26R48-1-1AA/26R48-2-1AA

QUICK OPERATING 1/4-TURN FASTENERS 2600/2700 SERIES

A-33

A

Clip-on VersionPart Number 99R11-1-1AA

Designed to clip-on .060 thick x.900 wide inner frame. Add .090to panel thickness used to deter-mine total grip, “G” select studdash number, then subtract sevendash numbers.Requires .438 diameter installation hole.

beckedc
Text Box
beckedc
Text Box

Recommended