Introduction to Terrestrial Laser
Scanning (TLS)
• Similar to Sonar and Radar but uses Light (Light
Detection and Ranging)
• Initial of LiDAR use began in the 1960’s in studies of
atmospheric composition, surveying, law enforcement,
etc.
• Transmits a pulse of light and records the returned pulse
of light – records time, divides by two, and multiplies by
the speed of light for distance
• Able to record thousands of points a second recording
target position (X,Y,Z), intensity, and color (RBG)
• Capable of relative positioning at mm to cm accuracy
LASER SCANNERSLASER SCANNERSLASER SCANNERSLASER SCANNERS
• Beam deflection mechanism provides elevation and azimuth of the transmitted pulse
• Return-beam detection device records return time and provides range calculation from two-way travel time
• Energy of the return pulse (intensity) and the color (RBG) is • Energy of the return pulse (intensity) and the color (RBG) is recorded
• Full waveform now recorded on some TLS instruments
Time-of-Flight Measurement
Transmitter
Receiver
Range = travel time x speed of light/2
Record (azimuth, zenith, range, intensity)
Greaves, SPAR 2004.
BENEFITS OF LASER SCANNERS
• Imaging system provides an unprecedented density of geospatial information through a dense set of three-dimensional vectors to target points relative to the scanner location (point cloud)
• Scanner controlled by laptop computer that is also used • Scanner controlled by laptop computer that is also used for data acquisition and initial processing
• Combination with GPS allows fully geospatially referenced data set and opens potential for direct measurement of change (time series measurements)
3D POINT CLOUD
• Cartesian transformation of the laser pulse data (trans-formation of the range and reflectance images as well as the calculated XYZ coordinates) in scanner centered reference frame
• 3D point cloud of discrete locations derived from superimposing range and reflectance image for each laser superimposing range and reflectance image for each laser pulse
• 3D point clouds are the basis for subsequent analysis and used to create CAD or GIS models
REFLECTANCE IMAGE
• Looks like a black and white photograph of scan coverage
• Individual measured points are defined as reflectance values– highly reflecting (light) points are displayed in a – highly reflecting (light) points are displayed in a
light grey pixel– highly absorbing
(dark) points are displayed as a dark grey pixel– lack of a return is depicted as a black pixel
Laptop
Field Equipment
Terrestrial
Laser
Scanner
(LPM 800)
Controls to
align all the
scanning
data
Field Equipment
Topcon Topcon Topcon Topcon
Totalstation Totalstation Totalstation Totalstation
Imagine Imagine Imagine Imagine
SystemSystemSystemSystem
Camera
RTK GPS
Tripod
Integrating geometry with textureIntegrating geometry with texture by by position position
controlcontrol
GPSGPS Imaging Total StationImaging Total Station
Camera
Nikon D200
Total StationTotal Station
TOPCON HIPER LITE+ - RTK GPS SYSTEM
TOPCON IS
TOPCON Total Station
Nikon D200
OR
Examples of controls
Scanner Parameters
• Beam Divergence
• Angular Step
• Range Distance
• Field of View• Field of View
• Points Per Second
• Size and Weight
Scanner Parameters
• Beam Divergence
Df = (Divergence * d) + Di
Scanner Parameters
Scanner Parameters
• Angular Step
Spacing = d(m)*TAN(step)
Scanner Parameters
Scanner Parameters
• Range DistanceTarget Reflectance can change single scan range by hundreds of meters
Laser and CCD characteristics impact maximum and minimum range
distances from <5 meters to >2000 (6000) meters
• Field of View• Field of ViewRotational Base allows 360 degree rotation (azimuth)
Rotating mirror and gear drive allows ~90 degree vertical coverage
• Points Per Second Scan Time
• Size and WeightField Logistics
Beam Stepping Distance
• Beam stepping angle is specified in either degrees/minutes/seconds, in decimal degrees or in gons. There are 400 gons in a circle, just as there are 360 degrees in a circle.
• Unfortunately, the specs units are not radians (2π radians in a circle). If they were radians, a very rapid approximation of the stepping distance in meters can be made mentally. For small angles,
Stepping Distance = (angle in radians) * distance
e.g. Stepping Angle = 0.00005 radians (.05 mRadians)e.g. Stepping Angle = 0.00005 radians (.05 mRadians)
Stepping Distance (@800m) = 0.00005* 800 = 4 cm
1 gon = 0.9 deg 1 deg = 1.111 gon
1 deg = 0.01745 radians
• Minimum specs for stepping tend to be 0.0012 => 0.004 deg
0.002 deg = 0.035 mRadians = 3.5 cm at 1000 meters
Beam Divergence
• Beam Divergence
– Optech Ilris 0.00974 deg (0.17 mRadian)
– Riegl LMS 620i 0.004 deg (0.07 mRadian)
– Riegl LPM 321 0.046 deg (0.8 mRadian)
• Beam diameter at exit ranges from a few millimeters to centimeters
• Spot diameter at distance
diameter = beam at exit + divergence (radians) * distance
Riegl 620 = 2 mm + (0.00007 radians * 500 m) = 3.7 cm
Riegl LPM = 1 cm + (0.0008 radians * 500 m) = 41 cm
Laser Return Signal
Beam size at laser = 1 cm2
Beam divergence = 0.8 mrad
Beam intensity at laser = 1 cm-2
Distance to outcrop = 500 m
Reflectivity = 33%( )
( )
( )26.033.0*0008.0*100
**Re
cm 0008.01257/1
/
cm 1257*2/40
*2/
cm 40 cm 50000*0008.0
*
2
2-
22
2
=
==
=
==
=
==
=
==
=
π
π
π
distance**2tcrop/ReturnAtOuernsityAtLasReturnInte
tyReflectivitOutcropIntensityAObjectArearopturnAtOutc
OutcropBeamAreaAtmIntensityInitialBeatOutcropIntensityA
rBeamDiamteOutcropBeamAreaAt
distancedivergenceperAtOutcroBeamDiamet
( )
001660.00000000
cm 66.1)50000**2/(26.0 2112
=
==
=
−π
π distance**2tcrop/ReturnAtOuernsityAtLasReturnInte
The return signal at the laser is substantially lower than the signal that is
emitted by the laser.
The example above assumes that the laser beam is 1 cm2 when it leaves the
laser and that the window to the receiver has an aperture area of 1 cm2 and
that the feature being imaged is 100 cm2.
Laser beam
with 3 milliradian div. Target
Diffuse reflection for reflectorless laser
rangefinders
diffuse reflection
Laser range-finder
receiver aperture
Not to scale
Material Description
Winter Snow and Ice
Vegetation (The Average Value of Many Types)
Soil
Silt
Sand
DR.
0.85
0.50
0.05 - 0.35
0.20 - 0.40
0.10 - 0.35
904 nm diffuse fractional reflections
of common materialOther lasers have different responses when operating at different wavelengths
SandGypsumClayDirtShale, CoralConcrete, AsphaltCoal Tar PitchPlywood, UnpaintedBrick, RedBark
0.10 - 0.35 0.55 - 0.700.40 - 0.500.30 0.45 0.10 0.05 0.50 0.250.20 - 0.25
Range Measurement versus IntensityCD Reflectors Mounted on a Wall
Note angle of points from wall pointing toward scanner
Range Error versus Intensity
LIDAR emits a short pulse of light and measures the time for the return
signal to reach the detector. Light travels at about 0.33 m / ns in air.
Distance = ½ * time of flight * velocity of light. Enough returned energy
must be received at the LIDAR detector to trigger the timing circuitry. If
the signal is very strong, the detector threshold will be reached faster than
if the signal is very weak. LIDAR detectors must compensate for this
effect in order to provide accurate measurement of distance.
LASER SCANNER ACCURACY
• Boehler, Vincent and Marbs, 2003.
• Tested scanners for accuracy
• Application was for cultural heritage
applications (we will revisit for natural applications (we will revisit for natural
surfaces)
• Manufacturer specifications not good
representation for real-world applications
LASER SCANNER ACCURACY
• Angular accuracy
– Angles from combination of deflection of rotating
mirrors and rotation about a mechanical axis
– Provides azimuthal position– Provides azimuthal position
• Range accuracy
– Time of flight or phase comparison between
outgoing and returning signal provides range
– Noise-fuzz of points on a flat surface
LASER SCANNER ACCURACY
• Resolution
– Ability to detect an object in point cloud
– Two specs contribute
• Smallest increment of angle between successive points • Smallest increment of angle between successive points
(can manually set)
• Size of laser spot (beam dispersion)
• Edge effects
– When a spot hits the edge of a target and receives
2 positions and/or 2 reflectivity values (material)
LASER SCANNER ACCURACY
• Surface reflectivity
– Distance, atmospheric, incidence angle
– Albedo (ability to reflect)
• White strong, black weak• White strong, black weak
• Depends on spectra of the laser (green, red, near IR)
• Inclined surfaces of high reflectance (i.e., water ) can
create travel time anomalies (mutlipathing)
– Typically contribute accuracy-range errors larger
than manufacture specifications
Environmental Conditions
• Temperature (important to operate within
specification range)
• Atmosphere
– changes propagation speed slightly– changes propagation speed slightly
– dust, mist, raindrops, fog - a major problem
• Interfering radiation
– Sunlight strong relative to signal
• Influence or prevent (don’t shoot into sun)
Survey Control
• Surface referencing (using recognizable
physiographic features)
• Targets (reflectors and/or prisms)
• Geo-referencing (Total Station and GPS • Geo-referencing (Total Station and GPS
positioning)
• Multiple scan registration requires tight spatial
control
Calibration
• Repeatability
– Need to document multiple measurements of
known geometry
– Compare with allowable variance– Compare with allowable variance
• Quality Control
– Multiple measurements of known geometry with
multiple scanner positions
Resolution
• Measurement accuracy is governed by
instrument resolution
• Resolution is the smallest distance that can be
measured without ambiguitymeasured without ambiguity
• For laser scanning, this is the spacing of the
point cloud array
• Varies linearly with distance from the scanner
Resolution
Range
Measurement Accuracy
• The ability to generate physical dimensions
and location of an object
– Specified with a tolerance, e.g. +/- 6 mm
(and a confidence interval)(and a confidence interval)
– Not a laser scanner specification but a work
product specification
Resolution and Measurement Accuracy
• Absolute measurement accuracy can’t be
better than 2x instrument resolution
Resolution and Measurement Accuracy
• Absolute measurement accuracy can’t be
better than 2x instrument resolution
Resolution and Measurement Accuracy
• Modeling may help, caution required
Resolution and Measurement Accuracy
• Overlapping dot problem (edge effect)
Resolution test
Measuring noise in range direction. Riegl Z420 is
comparable to Z360
Action Sequence in the Field
• First, establish the scan locations and ensure that they completely cover the target
area.
• Second, establish the location for the controls
• Third, review naming and number conventions to be used
• Make sure that the site name in the software and the folder and site abbreviation
in the camera set is correctly set (can be done night before)
• Set up controls and locate them with GPS (time series measurement reduce errors)
• Set up first scan site and decide on camera sites (if applicable)
• Scan controls before scanning the outcrop• Scan controls before scanning the outcrop
• The photo team with the Topcon IS needs to be working in parallel with the scan
team. One can get ahead of the other, but the jobs need to proceed in parallel. It
takes a lot of time.
• Review the progress with one another
• Double check the work
• Save all work to an archive file that is not used as a work file
• Review the data in the field if possible
• Start model construction as soon as possible in order to correct errors or fill in
unintentional holes in the data
LiDAR Site Selection
(multiple locations, selection of point density versus time)
• It is necessary to scan an outcrop from at least two oblique directions to minimize occluded parts of the outcrop. Three scans are good (left/center/right), and additional reverse directions are optimal.
• Point density is inversely dependent upon distance to the outcrop. If the distance has a wide range of values, the time to scan the outcrop can be optimized by selecting a finer outcrop. If the distance has a wide range of values, the time to scan the outcrop can be optimized by selecting a finer angular resolution for the more distant parts of the outcrop compared to the closer parts of the outcrop.
– Scan time is inversely dependent upon the square of the scan angluar resolution. Increasing the scan step angle by 2X reduces the scan time by 4X.
– Partition the outcrop scans to maintain a nearly uniform linear stepping distance at the outcrop surface.
Scan Positions
overhang
Choose scan positions to minimize occluded (shadowed or hidden)
geometries. Scanner blue will not image beneath the overhang or
the right side of the overhang. Scanner red will image underneath the
overhang and will image the right side of the overhang.
Moab Utah-Google Earth Screen Capture
Multiple Scan Positions
Moab Utah
Scan Partition as a Function of Range
Scan Partition as a Function of Angle of Incidence
Scan Partitioning Avoids Unnecessary Scan Time
Scan Partitioning
Scan of the “Pyramid” at Slaughter Canyon, Carlsbad Caverns National
Monument, New Mexico
Scanner was on a 200m high hill.
Scan ranges were 50m to 800m
Scan Partitioning
Scanning of the total outcrop at the scan step angle needed for the longest
scan would have dramatically increased the scan time.
Scanning the outcrop in a single scan which covered the entire outcrop would
Result in a large amount of empty data.
Placement and Survey of the Controls
• Use of scanned control reflectors improves the accuracy of the model and allows straight forward alignment of the individual scans
• Alignment of two scans requires an absolute minimum of three control points. It is best to have five or more available to accommodate errors.
• If multiple scan sites are used, it is not necessary to have all control reflectors visible from all of the scan sites. However, it is necessary that each scan site be able to see at least three reflectors that have been correlated with other scan sites
• The control reflectors should cover a wide area (preferably surrounding • The control reflectors should cover a wide area (preferably surrounding the image area), do not place reflectors in a linear fashion or group them in a tightly.
• The spacing of the reflectors optimally approximates or exceeds the distances in the scan region. However, this may not be practical.
• It is not necessary to have reflectors on the outcrop and/or within the image area, although it is desirable to do so if practical and is aesthetically acceptable (for photorealistic analysis).
Placement and Survey of the Controls
Scan Reflectors before Scanning Outcrop
• It is prudent to scan the reflectors before scanning the outcrop.
– If you do not have the controls with the scan data, you may not be able to use the scans
– If something happens to disorient the scanner or there is a power or software crash during the subsequent scans, the work up to that point can still be used
– For double protection, rescan at least some of the reflectors after – For double protection, rescan at least some of the reflectors after completing the outcrop scan. If the scanner has lost alignment, the final reflector scan will identify the problem.
• When using the LPM with the telescopic sight, the scan window must be larger than expected. There is parallax between the scanner and the telescope. This is a much larger problem at close range than at long range.
Collecting Field Data
Scan Pos 1
GPS Control
GPS
Photo Control
Collecting Field Data
Scan Pos 1
GPS
Collecting Field Data
Scan Pos 1
GPS
Collecting Field Data
GPS
Scan Pos 2
Collecting Field Data
GPS
Scan Pos 2
Collecting Field Data
GPS
Scan Pos 2
Collecting Field Data
Photos
Photos
Photos
Geospatial Referencing: GPSSummary of the approximate accuracy of GPS positioning versus methods. (Modified from
Featherstone, 1995)
• Accurate measurement of reference network
baselines with Total Station (mm)
• Time series measurement of individual reference
High-Resolution Geospatial Referencing: GPS
and Total Station
• Time series measurement of individual reference
reflectors/prisms with continuous GPS (cm)
• Simultaneous GPS solution of all reference sites and
network adjustment using TS baselines to provide
sub-cm results
Mickey Hot Springs, SE OregonZOOM OF DOQ
Problem: map a flat terrain and generate a cm level terrain map not feasible with airborne methods
DETAILED
AREA
470M
ZOOM of DOQ
Riegl Z360 mapping fairly flat surface
Actual examples of scans at MHS with RGB
channel so points are colored (not external
camera)
Scans 2, 3 and 4 are of detailed areas
Scans in southern area
Rotation of initial scan.
Note vegetation
Another perspective. Note shadows with
no points.
Perpendicular perspective
Example of merged scans
(reflectance image)
Color Version
Merged surface fit