Part 1:
Loading Battens – Tie-In Leech Adjuster.
Before inserting the battens, make sure the silver spectra
loop is hanging freely OUTSIDE of the sail (Figure 1).
Battens are labeled with Batten #1 closest to the head of the
sail. If your sail has RBS Rocket Tensioners, skip to Part 2.
Insert the batten into the pocket so the Black Hole Cap
is about 2” past the leech of the sail (Figure 2).
Thread the tensioning line down through the slot in the
sail (1), down through the Black Hole Cap (2), through the
spectra loop (3), back up through the Black Hole Cap (4), and
back up through the slot in the sail (5).
Pull the tensioning line (Figure 3).
This fishes the spectra loop up through the Black Hole Cap
and into the velcro pouch. At the same time the batten
should settle fully into the pocket.
Set up a 3:1 lashing (Figure 4).
More power than a 3:1 is not needed, as it makes it too easy
to over-tension the batten. The purchase system is NOT
to add tension. It is there to allow for finer adjustment and
make it easier to tie a knot without slippage. Finish with a
few half hitches over the lashing and tuck the tail out of the
way (Figure 5).
See Part 3 for additional tensioning tips!
Figure 1
Figure 5
Figure 4
Figure 3
Figure 2
1 2
3
4
5
NORTH SAILS 3Di BATTENINSTALLATION & TENSIONING GUIDE PLEASE READ! 3Di sails generally require less batten tension than other sails. Loose is fast!
This means extra care must be taken to not over-tension the batten, given the mechanical advantage offered by both the
Tie-in and RBS Rocket Tensioner leech end adjusters. This guide will explain how to insert and set up the battens with the
correct tension for both a smooth sail shape and to maintain your sails’ longevity. It remains important to release any batten
tension at the end of every day of sailing.
Version 2.0, Winter 2016
www.northsails.com
Part 2:Battens with an RBS Rocket Tensioner.
Battens are labeled with Batten #1 closest to the head of
the sail.
Insert the batten into the pocket between the
webbings and red flaps (Figure 6).
Gently push the webbing loops apart before inserting the
batten fully so the wings of the tensioner can slide past them
into the pocket, making sure the tensioning screw head is
flush with the end of the tensioner. Don’t use a sharp object
to pry the webs from under the wings or try to grab them
with pliers.
If it is very difficult to get the wings past the webs, remove
the batten and loop a piece of light line through the webs to
pull them apart (Figure 7). Also it may be easier to focus on
one web at a time, starting with the one closer to the leech.
Seat the webs into the wings (Figure 8).
Once the wings are past the webs, push them together so
they are secure on the wings. The webs may cover the wings.
This is OK.
GENTLY add tension (Figure 9).
Using the supplied RBS screwdriver, gently turn the
tensioning screw clockwise. Again, it is very easy to over-
tension the batten. Simply taking the slack out of the system
is usually enough.
See Part 3 for additional tensioning tips!
Figure 6
Figure 9
Figure 8
Figure 7
www.northsails.com
Part 3:Perfect Batten Tension.
Do not over-tension! Loose is fast!
Most batten related problems are due to overtensioning.
The ideal amount may be less than expected. Tension is
correct when the sail is smooth.
Recognizing over-tensioning at the dock.
• There is a large football shaped distortion, roughly parallel
to the batten pocket, emanating from the batten ends
(Figure 10).
• The batten takes on a curved shape, similar to a boat’s
mast bend under rig tension. If this bend can be “popped”
from side to side, IMMEDIATELY loosen the tension as
permanent sail damage can result!
• The middle part of the batten is clearly visible, or appears to
be standing proud inside the batten pocket.
Recognizing over-tensioning on the water.
• The large football shaped wrinkles sharpen to V-shaped
wrinkles from one or both ends of the batten (Figure 11).
• The tip of the batten appears to lift to windward, which also
looks like a depression in the sail to leeward (Figure 12).
• The batten can force excessive curve in the leech of the sail,
or even invert completely.
• After a tack or gybe, the batten remains in its previous
position.
Tips for perfect batten tension.
• When in doubt, start with a loose setup and gradually add
tension, not the other way around.
• Place a pencil under the lashing while setting the tension,
and remove it once the lashing is set (Figure 13). This adds
an extra safety factor and also helps with consistent tension
on all battens.
• As the Rocket Tensioner screw is turned to add tension, it
will be obvious when it starts to work against the pocket.
When this happens, stop and loosen the screw 1/2 turn.
Figure 10
Figure 13
Figure 12 Too much tension = distortion at tips
Correct tension = smooth at tips
Figure 11
( )
Notes:
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
_____________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
_____________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
______________________________________________________________________________________________________________
www.northsails.com