Motion Control SolutionsServo Drives Minas A4 / FP-Series PLCs
AUTOMATECH Sp.z o.o. www.automatech.pl e-mail: [email protected] Tel.: +48 22 723 0606 Fax: +48 22 723 0662
Dystrybutor w Polsce:
2
Overview
Panasonic Motion Control Solutions
FP-SERIESThe compact FP (Sigma) is suitable for most applications. The FP (Sigma) PLC itself haspowerful features for up to two axes. Add FP (Sigma) positioning units to control up to10 independent axes. The new FP-X PLC with transistor outputs offers functionality similar to theFP (Sigma). The FP2/FP2SH is also suitable for complex positioning applications, while thecompact FP0 and FP-e can handle simple positioning tasks.
MINAS A4 SERIES SERVO MOTORS AND DRIVERSPowerful servo drives with cutting edge technology, high power density and a power range of50W to 5kW.
SOFTWARWW EUse any of the built-in functions for FP (Sigma) for up to two axes or the certified Motion ControlLibrary for more complex tasks that require positioning units.
FP-SERIESPLCs
SERVO DRIVESMINAS A4SERIES
SOFTWAREA B
CA
B
C
2
FP-Series PLCsFP (Sigma) – High-Speed, High Precision
A
3
GENERAL FEATURES
4
Positioning with FP (Sigma)
FP-Series PLCsA
Max. 100kHz pulse output performance is now standard.Powerful device capable of linear interpolation and circular interpolation.
RAPID 0.02ms START (WHEN JOG OPERATION CONTROLS ARE EXECUTED)The time taken to execute the JOG operation, from the instant the trigger (execution condition) goes on to the time of pulse output, is 0.02ms and 0.2ms with trapezoidal control. Control time is reduced even for machines that quickly and repeatedly restart.
Adhesive
LINEAR INTERPOLATION AND CIRCULARINTERPOLATION ARE BUILT-IN(FPG-C32T2H AND FPG-C28P2H)
Interpolation functions enable simultaneous control of two axes. Applications that a compact PLC couldn‘t previously cope with are no longer a challenge.
Linear Interpolation Circular Interpolation
Motordriver
Motordriver
AND THERE’S MORE...Smooth acceleration/decelerationYou can choose to set either 30 or 60 steps of acceleration/ deceleration. This feature means you can achieve smoother movement during long acceleration /deceleration periods of stepping motors.
The settings are there for a maximum 60 acceleration/deceleration steps.
Support for CW/CCW methodReduce overall costs by designing systems that combine with servomotors and small stepping motors without support for pulse and sign methods.
CW
/ C
CW
m
etho
dP
ulse
/ S
ign
met
hod
Stepping motorServo motor
Motordriver
1
Y0
Pulse output CW
Y1
Pulse output CCW
Y3
Pulse output CW
Y4
Pulse output CCWMotordriver
2
PULSE OUTPUT MAX. 100kHzBecause command processing at speeds up to 100kHz is available, high-speed, high-precision positioning is enabled. Along with stepping motor control, the specs also ensure plenty of scope for controlling servomotors.
Possible to combine with pulse-train input driversSingle unit enables two-axis control
Servomotor
Positioning with FP (Sigma)
5
FP-Series PLCsA
PROGRAMMING WITH CONVENIENT ANDEASY-TO-UNDERSTAND INSTRUCTIONS
• Uses a preset value table for starting speed, target speed, acceleration/ deceleration time, and other factors. Easy-to-understand programming is possible since numbers can be specified intuitively.
• Comes with dedicated instructions for each mode: trapezoidal control, home return, JOG operation, free table operation, linear interpolation, and circular interpolation.
SELECTABLE HOME RETURN MODE• The home return method may be specified even in situations
such as when only a single sensor is being used, depending on the design.
• When the home position return is completed, a deviation counter clear signal can also be output.
Home sensorON
XA ON
2000Hz
100Hz0Hz
150ms
HOME POSITION RETURN• Pulse output diagram
(when the home position proximity input is not used).
ONOFF
300Hz
0Hz
XB (JOG command)
Y0 (Pulse)
JOG OPERATION• Pulse output diagram
Home search automatically reverses the motor rotation when over limit (+ or -) is input and searches for the home position or near home position in order to return to it automatically.
This refers to an operation in which the motor is rotated only while operation commands are being input. This is used to forcibly rotate the motor using input from an external switch, for instance when making adjustments. Depending on the circumstances, unlimited feeding can be accomplished with the JOG operation in some cases.
X-axis(CH0)
Y-axis(CH2)
5000
2000
LINEAR INTERPOLATION• Positioning Iocus.
Pass position P(X 9396, Y -3420)
Target position E(X 8660, Y -5000)
Current position S(X 5000, Y 8660)
θ Center position O
(Xo,Yo)
CIRCULAR INTERPOLATION• Positioning Iocus.
• Center-radialsetting methods arealso available.
A control function that automatically defines the continuum of points in a straight line based on only two co-ordinate positions.
Allows points to be smoothly traversed by arced paths for which the user specifies the orientation plane, the radius of curvature, motion path profile, and direction of motion.
6
FP (Sigma) Positioning Units
1-axistransistor output
FPG-PP11
1-axisline driver output
FPG-PP12
2-axistransistor output
FPG-PP21
1. High-speed pulse and startup for great performance is a compact package and even supports linear servos.Max. output frequency: 4 Mpps, Startup speed: 0.005 ms
2. Supports indexed feeding with JOG positioning function. Able to support indexed feed processing applications with high-speed startup and repeated control.
3. Count of feedback pulse possible. Since feedback pulses from encoders, etc., can be counted, control is possible while detecting whether themotor is out of step or verifying the current position in step motors.
2-axisline driver output
FPG-PP22
*1: When linear acceleration /deceleration operation is selected, the target speed can be changed during operation.
*2: The startup time can be changed by the control code setting in the shared memory.The factory setting (default setting) is 0.02ms.The startup time is the time from the start request to the first pulse output.
*3: Pulser input function and feedback counter function use the same pulse input terminal, so both cannot function simultaneously.
PERFORMANCE SPECIFICATIONS
FEATURES
FP-Series PLCsA
FP2 and FP2SH PLCs
7
GENERAL FEATURES OF FP2 / FP2SH High program capacity: FP2 16k or 32k steps, FP2SH 60k or 120k stepsHigh memory capacity: data registers: 6000 words (FP2), 10,240 words (FP2SH)Additional file registers: up to 30,717 words (FP2) and 3 x 32,765 words (FP2SH)Serial interfaces: 2 RS232C on CPU Communication modules: Serial Data Units or Computer Communication Modules with 2 additional
ports each available, Profibus DP/FMS Ethernet moduleHigh expansion capability: up to 28 modules or 2048 I/Os are possibleFast processing speed: FP2 0.35µs / basic instruction,
FP2 SH 0.03µs powerful instruction setSmall size: 140 x 100 x 93mm (WxHxD) for 5-module backplane
Extended debugging functions: testmode and breakpoints can be used
POSITIONING UNITS FOR FP2 AND FP2SH• Super fast startup of 0.005ms
• Up to 4 Mpps speed command
for high-speed, high-accuracy positioning.
• Feedback pulse count function (for encoders)
• Transistor / line driver output
• Clockwise / counterclockwise or pulse/direction
• 64 (88) independent axis positioning
• Up to 500kpps / 4Mpps
• Pulse range: 32-bit, signed
Operation modes:• Interpolation
• Single speed acceleration / deceleration
• Multistage acceleration / deceleration
• Fast startup of 0.02 or 0.005ms makes cycle time reduction possible.
• Acceleration / deceleration control:linear or 4 types of S-curve: sine, quadratic, cycloid and cubic curve (for smooth startup and stopping)
UP TO FOUR AXES PER POSITIONING MODULE:
Part No. Output Type Type
FP2-PP22 Line driver output 2-axis type
FP2-PP42 Line driver output 4-axis type
Motor
Motor
Driver
Driver
4-axis typeFP2-PP42
Driver
Driver
Motor
Motor
FP-Series PLCsA
8
Main Features – Increased Performance and Accuracy
Minas A4 Series Servo DrivesB
Motor output power rating: 50W to 5kW
Nominal/Maximum speed: 3000/5000 rpm
Nominal torque: 0.16 to 42.9 Nm
Peak torque: 0.48 to 107.0 Nm
Encoder:incremental 2500 pulses/rev (standard)
absolute 17-bit (on demand only)
• Fast response frequency: 1000Hz
• Completely adjustment-free, real-time auto-gain tuning
• High performance vibration control
• Command input up to 2 Mpps
• Smaller motors and drivers compared to theformer series
• Position, velocity and torque control supporta wide range of applications in one driver
• Many more additional functions:- Hit & Stop Homing, i.e. homing without needing a switch- Press/Tension control- 8 internal JOG speeds- etc.
Details of Features
9
ADJUSTMENT-FREE OPERATIONHigh-functionality real-time auto-gain tuning• Automatically tunes in real-time to variations in load inertia. Real-time auto-gain tuning for machines with low or high stiffness.
• Supports vertical axis applications where the load torque varies depending on rotational direction.
• An over-travel detection function prevents the machine from over-travelling during real-time auto-gain tuning.
• Enables you to set and check while monitoring real-time automatic gain tuning conditions on the front panel.
HIGH-SPEED AND FAST RESPONSEVelocity response (bandwidth) of 1kHz• The instantaneous Velocity Observer detects the motor speed more quickly and with a higher resolution than the previous models.
High-functionality real-time auto-gain tuning• Enables low stiffness machines (e.g. belt-driven machines) and high stiffness machines (e.g. short stroke ball-screw driven
machines) to be used in high-speed positioning applications.
Corresponds to wide frequency range (-1500Hz)Suppresses vibration quickly
4000
3200
2400
1600
800
0
-800
-1600
-2400
-3200
-4000
180
160
140
120
100
80
60
40
20
0
-20
Minas A4 Series Servo DrivesB
Actual speed (r/min)
10
Details of Features
REDUCTION VIBRATIONAdaptive Filter• Enables the notch filter frequency to automatically follow the
machine resonance frequency.
• Suppresses "Judder" noise of the machine caused by a change in the resonance frequency (e.g. resutling from aging effects or changeovers).
DAMPING CONTROL• The driver is equipped with a 2-channel damping filter. You can suppress vibration occurring at both starting and stopping in low
stiffness machines, by manually setting up vibration frequencies in 0.1Hz units.
• You can also switch between the channels either by the rotation direction or with an external input.
• Easy setup with entry of only frequency and filter value. Improper setup values do not result in unstable operation.
Effect of notch filter
without notch filter with notch filter
50ms/div 50ms/div
motor movement machine movement
without damping control
with damping control
Minas A4 Series Servo DrivesB
2-CHANNEL NOTCH FILTERSAdaptive Filter• 2-channel notch filters are equipped in the driver, independent
of the adaptive filter.
• You can set up both frequency and width for each of the2 filters. You can define the frequency in units of 1Hz.
• Suppress "Judder" noise of machines with multiple resonance points.
Additional Features
11
SETUP SUPPORT WITH HELPFULMONITORING FUNCTIONS
• Faster communication speed of RS232C/RS485 (Max. 57600bps) establishes an easy and comfortable operating condition for setup support software, "PANATERM®".
• "PANATERM®" display useful status information, e.g. to help you analyse motor troubles.
• You can enable the panel operation lock to inhibit operation via the front panel, e.g. to prevent parametres from being changed unintentionally.
COMMAND CONTROL MODES• Offers you "Position", "Velocity (including internal 8-speed)"
and "Torque" command control modes.
• You can set up any one of the command control modes, or selectable two command control mode with parameter.
• You can combine command control modes in a hybrid mode and switch between them.
MONITORING FUNCTION WITHFRONT PANEL
• LED display and analog monitor terminals are installed in the front panel.
• Displays "Motor speed" , "Motor torque", "Position deviation" , "Motor load factor" and "Regeneration load factor".
• You can monitor "Motor speed" ,"Motor torque" and "Position deviation" through analog monitor terminals.
TRIAL RUN (JOG)• Features the function for trial (JOG) run through the front panel
or console (option) without connecting to a host controller.
• Shorten machine setup time.
FULL-CLOSED CONTROL(HIGH PRECISION POSITIONING)
• Features the full-closed control of position and velocity, using the signals from linear scale installed on the load side and high resolution encoder.
• Best suited to high precision machines.
INRUSH CURRENT SUPPRESSINGFUNCTION
• The driver is equipped with an inrush suppressing resistor which prevents circuit breaker shutdown of the power supply caused by inrush current at power-on.
• Prevents unintentional shutdown of the power supply circuit breaker in multi-axis applications and does not add load to the power line.
REGENERATION DISCHARGINGFUNCTION
• Discharges regenerative energy, which is returned from the motor to the driver with a resistor, e.g. stopping a load with a large moment of inertia, or up-down operation.
• Frame A and Frame B drivers do not have a built-in regeneration discharge resistor. We recommend connecting an optional regenerative resistor.
• Frame C – Frame F drivers have a built-in regeneration discharge resistor. However, connecting an optional regenerative resistor will add even more regenerative capability.
BUILT-IN DYNAMIC BRAKE• The driver is equipped with a dynamic brake for emergency
stop.
• The dynamic brake can be used in the following cases:- Main power OFF- Servo OFF- A protective function- Over-travel inhibit is activated
POSITIONING PULSE• Up to 2Mpps of pulse input at positioning control possible.
TORQUE LIMIT VALUE SWITCHING• You can set up 2 torque limits and use them for tension control
or press & hold control.
Minas A4 Series Servo DrivesB
12
Overview Minas A4 Drivers
MINAS A – MINAS A4 CROSS REFERENCE
Minas A Drivers (old) Minas A4 Drivers (new)
MSDA5A5A1A 50W Incr. encoder, 1 phase 200VMADDT1205
MSDA015A1A 100W Incr. encoder, 1 phase 200V
MSDA023A1A 200W Incr. encoder, 1 phase 200V MADDT1207
MSDA043A1A 400W Incr. encoder, 1 phase 200V MBDDT2210
MSDA083A1A 750W Incr. encoder, 1 phase 200V MCDDT3520
MSDA103A1A 1kW Incr. encoder, 1 phase 200VMDDDT5540
MSDA153A1A 1.5kW Incr. encoder, 1 phase 200V
MSDA203A1A 2kW Incr. encoder, 1 phase 200V MEDDT7364
MSDA253A1A 2.5kW Incr. encoder, 1 phase 200V –
MSDA303A1A 3kW Incr. encoder, 1 phase 200V MFDDTA390
MSDA353A1A 3.5kW Incr. encoder, 1 phase 200V –
MSDA403A1A 4kW Incr. encoder, 1 phase 200V MFDDTB3A2
MSDA453A1A 4.5kW Incr. encoder, 1 phase 200V –
MSDA503A1A 5kW Incr. encoder, 1 phase 200V MFDDTB3A2
PRODUCT NUMBER LEGEND
M A D D T 1 2 0 5 * * *
Minas A4 Series Servo DrivesB
*
*
* Not for use in Europe
Please note: Not all type combinations are possible. Please use the table below for selection.
Common Specifications of Driver
13
Inp
ut
po
wer
200V Mai
n c
ircu
itFrame A, B Single phase, 200-240V
+10%50/60Hz-15%
Frame C, D Single/3-phase, 200-240V+10%
50/60Hz-15%
Frame E, F 3-phase, 200-230V+10%
50/60Hz-15%
Co
ntr
ol
circ
uit
Frame B, C Single phase, 200-240V+10%
50/60Hz-15%
Frame E, F Single phase, 200-230V+10%
50/60Hz-15%
Environment
Temperature Operating : 0 to 55°C , Storage : -20 to +80°C
Humidity Both operating and storage : 90%RH or less (free from condensation)
Altitude 1000m or lower
Vibration 5.88m/s2 or less, 10 to 60Hz (No continuous use at resonance frequency)
Control method IGBT PWM sinusoidal wave drive
Encoder feedback 17-bit (131072 resolution) absolute/incremental encoder (on demand only),2500P/r (10000 resolution) incremental encoder (standard)
External scale feedback AT500 series, ST771 by Mitsutoyo
Control signal
Input10 inputs(1) Servo-ON, (2) Control mode switching, (3) Gain switching/Torque limit switching, (4) Alarm clearOther inputs vary depending on the control mode
Output6 outputs(1) Servo alarm, (2) Servo ready, (3) Release signal of external brake (4) Zero speed detection,(5) Torque in-limit. Other outputs vary depending on the control mode
Analog signal
Input 3 inputs (16Bit A/D : 1 input, 10Bit A/D : 2 inputs)
Output
2 outputs (for monitoring)(1) Speed monitor (Monitoring of actual motor speed or command speed is enabled. Select the content and scale with parameter.), (2) Torque monitor (Monitoring of torque command, (approx.3V/rated torque)), deviation counter or full-closed deviation is enabled. Select the content or scale with parameter
Pulse signal
Input 2 inputsSelect the exclusive input for line driver or photo-coupler input with parameter
Output4 outputsFeed out the encoder pulse (A, B and Z-phase) or external scale pulse (EXA, EXB and EXZ-phase) in line driver. Z-phase and EXZ-phase pulse is also fed out in open collector
Communicationfunction
RS232C 1:1 communication to a host with RS23C interface is enabled
RS485 1:n communication up to 15 axes to a host with RS485 interface is enabled
(1) 5 keys (MODE, SET, UP, DOWN, SHIFT), (2) LED (6-digit)
Front panel regeneration Frame A, B: no built-in regenerative resistor (external resistor only) Frame C to F: Built-inregenerative resistor (external resistor is also enabled)
Dynamic brake Setup of action sequence at Power-OFF, Servo-OFF, at protective function activation and over-travelinhibit input is enabled
Control modeSwitching among the following 7 mode is enabled, (1) Position control, (2) Velocity control, (3) Torque control, (4) Position/Velocity control, (5) Position/Torque control, (6) Velocity/Torque control and (7) Full-closed control
Minas A4 Series Servo DrivesB
Common Specifications of Driver
14
Func
tions
Pos
ition
con
trol
Control input (1) Deviation counter clear, (2) Command pulse inhibition, (3) Electronic gear switching, (4) Damping control switching
Control output Positioning complete (In-position)
Pul
se in
put
Max. command pulse frequency Exclusive interface for line driver : 2Mpps, Line driver : 500kpps, Open collector : 200kpps
Input pulse signal format Support (1) RS422 line drive signal and (2) Open collector signal from controller
Type of input pulse Differential input. Selectable with parameter, ((1) CW/CCW, (2) A and B-phase, (3) Command and Direction)
Electronic gear (Division/Multi-plication of command pulse) Process the command pulse frequency x as a position command input
Smoothing filter Primary delay filter or FIR type filter is selectable to the command input
Analo
gue-
input Torque limit command input Individual torque limit for both CW and CCW direction is enabled. (3V/rated torque)
Instantaneous speed observer Usable
Damping control Usable
Velo
city
con
trol
Control input (1) Speed zero clamp, (2) Selection of internal speed setup, (3) Gain switching or Torque limit switching input
Control output Speed arrival (at-speed)
Anal
ogue
-in
put Velocity command input Setup of scale and rotational direction of the motor against the command voltage is enabled with parameter, with the permissible max.
voltage input = 10V and 6V/rated speed (default setup)
Torque limit command input Individual torque limit for both CW and CCW direction is enabled. (3V/rated torque)
Speed control range 1 : 5000
Internal speed command 8-speed with parameter setup
Soft-start/down function Individual setup of acceleration and deceleration is enabled, with 0 to 10s/1000r/min. Sinusoidal acceleration/deceleration is also enabled
Zero-speed clamp 0-clamp of internal speed command with speed zero clamp input is enabled
Instantaneous speed observer Usable
Speed command filter Usable
Torq
ue c
ontr
ol
Control input (1) CW over-travel inhibition, (2) CCW over-travel inhibition, (3) Speed zero clamp
Control output Speed arrival (at-speed)
Anal
ogue
-in
put Speed command input Setup of scale and CW/CCW torque generating direction of the motor against the command voltage is enabled with parameter, with the
permissible max. voltage input = 10V and 3V/rated speed (default setup)
Speed limit input Speed limit input by analog voltage is enabled. Scale setup with parameter
Speed limit function Speed limit value with parameter or analog input is enabled
Full-
clos
ed c
ontr
ol
Control input (1) CW over-travel inhibition, (2) CCW over-travel inhibition, (3) Deviation counter clear, (4) Command pulse input inhibition,(5) Electronic gear switching, (6) Damping control switching
Control output Full-closed positioning complete (in-position)
Pul
se in
put
Max. command pulse frequency Exclusive interface for line driver : 2Mpps, Line driver : 500kpps, Open collector : 200kpps
Input pulse signal format Differential input. Selectable with parameter ((1) CCW/CW, (2) A and B-phase, (3) Command and direction
Electronic gear Division/Multiplica-tion of command pulse Process the command pulse frequency x as a position command input
Smoothing filter Primary delay filter is adaptable to the command input.
Analo
gue-
input Torque limit command input Individual torque limit for both CW and CCW direction is enabled. (3V/rated torque)
Setup range of division /multiplication of external scale
Setting of ratio between encoder pulse (denominator) and external scale pulse (numerator) isenabled within a range of (1 to 10000) x 2(0-17) / (1 to 10000)
Com
mon
Aut
o-ga
in tu
ning Real-time Corresponds to load inertia fluctuation, possible to automatically set up parameters related to notch filter
Normal mode Estimates load inertia and sets up an appropriate servo gain
Fit-gain function Automatically searches and sets up the value which makes the fastest settling time with external command input
Masking of unnecessary input Masking of the following input signal is enabled.(1) Over-travel inhibition, (2) Torque limit, (3) Command pulse inhibition, (4) Speed-zero clamp
Division of encoder feedback pulse Set up of any value is enabled (encoder pulses count is the max.)
Prote
ctive
functi
on Soft error Over-voltage, under-voltage, over-speed over-load, over-heat, over-current and encoder error etc.
Hard error Excess position deviation, command pulse division error, EEPROM error etc.
Traceability of alarm data Traceable up to past 14 alarms including the present one
Damping control function Manual setup with parameter
Set
up
Manual 5-push switches on front panel MODE SET
Setup support software PANATERM (Supporting OS : Windows95, Windows98, Windows ME, Windows2000, Windows.NET and Windows XP)
(1 to 10000) x 2(0-17)
1 to 10000
(1 to 10000) x 2(0-17)
1 to 10000
14
Minas A4 Series Servo DrivesB
Driver Dimensions
15
FRAME A
FRAME B
RB2RB3
FRAME C
Minas A4 Series Servo DrivesB
Driver Dimensions
RB2RB3
FRAME D
FRAME E
16
FRAME F
16
Minas A4 Series Servo DrivesB
Motor Types Cross Reference Minas A – Minas A4
17
Minas A Series motors low inertia, incremental encoder
Minas A motorsproduct no. (old)
ratedpower brake oil seal shaft IP67
plugsMinas A4 motorsproduct no. (new)
MSMA5AZA1A 50 W no no round no MSMD5AZP1A
MSMA5AZA1A-X 50 W no no round yes MSMD5AZP1AX
MSMA5AZA1B 50 W yes no round no MSMD5AZP1B *
MSMA5AZA1C 50 W no yes round no MSMD5AZP1C *
MSMA5AZA1D 50 W yes yes round no MSMD5AZP1D *
MSMA5AZA1E 50 W no no key no MSMD5AZP1S
– 50 W no no key yes MSMD5AZP1SX
MSMA5AZA1F 50 W yes no key no MSMD5AZP1T
– 50 W yes no key yes MSMD5AZP1TX
MSMA012A1A 100W no no round no MSMD012P1A
MSMA012A1A-X 100W no no round yes MSMD012P1AX
MSMA012A1B 100W yes no round no MSMD012P1B *
MSMA012A1C 100W no yes round no MSMD012P1C *
MSMA012A1D 100W yes yes round no MSMD012P1D *
MSMA012A1E 100W no no key no MSMD012P1S
MSMA012A1E-X 100W no no key yes MSMD012P1SX
MSMA012A1F 100W yes no key no MSMD012P1T
– 100W yes no key yes MSMD012P1TX
MSMA022A1A 200W no no round no MSMD022P1A
MSMA022A1A-X 200W no no round yes MSMD022P1AX
MSMA022A1B 200W yes no round no MSMD022P1B *
MSMA022A1C 200W no yes round no MSMD022P1C *
MSMA022A1D 200W yes yes round no MSMD022P1D *
MSMA022A1E 200W no no key no MSMD022P1S
MSMA022A1E-X 200W no no key yes MSMD022P1SX
MSMA022A1F 200W yes no key no MSMD022P1T
– 200W yes no key yes MSMD022P1TX
MSMA042A1A 400W no no round no MSMD042P1A
MSMA042A1A-X 400W no no round yes MSMD042P1AX
MSMA042A1B 400W yes no round no MSMD042P1B *
MSMA042A1C 400W no yes round no MSMD042P1C *
MSMA042A1D 400W yes yes round no MSMD042P1D *
MSMA042A1E 400W no no key no MSMD042P1S
MSMA042A1E-X 400W no no key yes MSMD042P1SX
MSMA042A1F 400W yes no key no MSMD042P1T
– 400W yes no key yes MSMD042P1TX
MSMA082A1A 750W no no round no MSMD082P1A
MSMA082A1A-X 750W no no round yes MSMD082P1AX
MSMA082A1B 750W yes no round no MSMD082P1B *
MSMA082A1C 750W no yes round no MSMD082P1C *
MSMA082A1D 750W yes yes round no MSMD082P1D *
MSMA082A1E 750W no no key no MSMD082P1S
MSMA082A1E-X 750W no no key yes MSMD082P1SX
MSMA082A1F 750W yes no key no MSMD082P1T
– 750W yes no key yes MSMD082P1TX
MSMA102A1C 1kW no yes round yes – **
MSMA102A1D 1kW yes yes round yes – **
MSMA102A1G 1kW no yes key yes MSMA102P1G
MSMA102A1H 1kW yes yes key yes MSMA102P1H
Minas A Series motors low inertia, incremental encoder
Minas A motorsproduct no. (old)
ratedpower brake oil seal shaft IP67
plugsMinas A4 motorsproduct no. (new)
MSMA152A1C 1.5kW no yes round yes – **
MSMA152A1D 1.5kW yes yes round yes – **
MSMA152A1G 1.5kW no yes key yes MSMA152P1G
MSMA152A1H 1.5kW yes yes key yes MSMA152P1H
MSMA202A1C 2kW no yes round yes – **
MSMA202A1D 2kW yes yes round yes – **
MSMA202A1G 2kW no yes key yes MSMA202P1G
MSMA202A1H 2kW yes yes key yes MSMA202P1H
MSMA252A1C 2.5kW no yes round yes – **
MSMA252A1D 2.5kW yes yes round yes – **
MSMA252A1G 2.5kW no yes key yes – **
MSMA252A1H 2.5kW yes yes key yes – **
MSMA302A1C 3kW no yes round yes – **
MSMA302A1D 3kW yes yes round yes – **
MSMA302A1G 3kW no yes key yes MSMA302P1G
MSMA302A1H 3kW yes yes key yes MSMA302P1H
MSMA352A1C 3.5kW no yes round yes – **
MSMA352A1D 3.5kW yes yes round yes – **
MSMA352A1G 3.5kW no yes key yes – **
MSMA352A1H 3.5kW yes yes key yes – **
MSMA402A1C 4kW no yes round yes – **
MSMA402A1D 4kW yes yes round yes – **
MSMA402A1G 4kW no yes key yes MSMA402P1G
MSMA402A1H 4kW yes yes key yes MSMA402P1H
MSMA452A1C 4.5kW no yes round yes – **
MSMA452A1D 4.5kW yes yes round yes – **
MSMA452A1G 4.5kW no yes key yes – **
MSMA452A1H 4.5kW yes yes key yes – **
MSMA502A1C 5kW no yes round yes – **
MSMA502A1D 5kW yes yes round yes – **
MSMA502A1G 5kW no yes key yes MSMA502P1G
MSMA502A1H 5kW yes yes key yes MSMA502P1H
Minas A4 Series Servo DrivesB
* only on demand, long delivery time** not available
18
Motor Specifications
AC200VMotor model MSMD 5AZP1 012P1 022P1 042P1 082P1
Applicable driverModel No. MADDT1205 MADDT1207 MBDDT2210 MCDDT3520
Frame symbol Frame A Frame B Frame C
Power supply capacity (kVA) 0.3 0.5 0.9 1.3
Rated output (W) 50 100 200 400 750
Rated torque (N • m) 0.16 0.32 0.64 1.3 2.4
Momentary Max. peak torque (N • m) 0.48 0.95 1.91 3.8 7.1
Rated current (Arms*) 1.1 1.6 2.6 4
Max. current (Ao-p) 4.7 6.9 11.0 17.0
Regenerative brake frequency(times/min) 1
Without option No limit 2
With externalbrake resistor No limit 2
Rated rotational speed (r/min) 3000
Max. rotational speed (r/min) 5000 4500
Moment of inertiaof rotor(x10-4 kg • m2)
Without brake 0.025 0.051 0.14 0.26 0.87
With brake 0.027 0.054 0.16 0.28 0.97
Recommended moment of inertia ratio of the load and the rotor 3 Smaller than 30 times Smaller than 20 times
Rotary encoder specifications 2500P/rIncremental
Resolution per single turn 10000
Protective enclosure rating IP65 (except shaft through hole and cable end connector)
Environment
Ambienttemperature 0°C to 40°C (free from freezing), Storage : -20°C to + 80°C
Ambient humidity 85%RH or lower (free from condensing)
Installation location Indoors (no direct sunlight), free from corrosive gas, inflammable gas, oil mist and dust
Altitude 1000m or lower
Vibration resistance 49m/s2 or less
Mass (kg), ( ) representsholding brake type 0.32 (0.53) 0.47 (0.68) 0.82 (1.3) 1.2 (1.7) 2.3 (3.1)
Brake specifications (This brake will be released when it is energized. Do not use this for braking the motor in motion.)
Static friction torque (N • m) 0.29 1.27 2.45
Engaging time (ms) 35 50 70
Releasing time (ms) 4 20 (–) 15 (–) 20 (–)
Exciting current (DC) (A) 0.30 0.36 0.42
Releasing voltage DC1V or more
Exciting voltage DC 24 V 5%
Permissible load
During assembly
Radial loadP-direction (N) 147 392 686
Thrust loadA-direction (N) 88 147 294
Thrust loadB-direction (N) 117 196 392
During operation
Radial loadP-direction (N) 68 245 392
Thrust loadA-direction (N) 58 98 147
Thrust loadB-direction (N) 58 98 147
Minas A4 Series Servo DrivesB
For notes 1-4, see page 22*rms= root mean square
Torque Characteristics
19
MSMD5AZ 1
0.5
0 1000 2000 3000 4000 5000
1.0
�
�5
50
0 10 20 30 40
100
757050
0 10 20 30 40
100
0.5
0 1000 2000 3000 4000 5000
1.0
�
�0.�5��
�0.32��
�0.�5��
�0.32��
℃
℃
MSMD012 1
MSMD022 1
8070
0 10 20 30 40
100
1.0
0 1000 2000 3000 4000 5000
2.0
2.0
0 1000 2000 3000 4000 5000
4.0�0
50
0 10 20 30 40
100
�
2.0
0 1000 2000 3000 4000 5000
4.0
�
75
50
0 10 20 30 40
100
1.0
0 1000 2000 3000 4000 5000
2.0
�
50
0 10 20 30 40
100�1.�1��
�0.64��
�1.�1��
�0.64��
�3.8��
�1.3��
�3.8��
�1.3��
℃
℃
℃
℃
MSMD042 1
MSMD082 1
50
0 10 20 30 40
100
4.0
0 1000 2000 3000 4000 5000
8.0
�
4.0
0 1000 2000 3000 4000 5000
8.0
�
50
0 10 20 30 40
100�7.1��
�2.4��
�7.1��
�2.4��
℃
℃
0.25
0 1000 2000 3000 4000 5000
0.5 �5
50
0 10 20 30 40
100
�
0.25
0 1000 2000 3000 4000 5000
0.5
706050
0 10 20 30 40
100
�
�0.48��
�0.16��
�0.48��
�0.16��
℃
Minas A4 Series Servo DrivesB
Wit
h o
il se
alW
ith
ou
t o
il se
al
Wit
h o
il se
alW
ith
ou
t o
il se
al
Wit
h o
il se
alW
ith
ou
t o
il se
al
Wit
h o
il se
alW
ith
ou
t o
il se
al
Wit
h o
il se
alW
ith
ou
t o
il se
al
20
Motor Dimensions
MSMD 50W – 750W (LOW INERTIA)
�
�
□
�
��7���7��
Dimensions are subject to change without notice. Contact us or a dealer for the latest information.
MSMD series (low inertia)Motor output 50W 100W 200W 400W 750W
Motor model MSMD 5A P1 01 P1 02 P1 04 P1 08 P1
Rotary encoder specifications 2500P/r incremental
LLWithout brake 72 92 79 98.5 112
With brake 102 122 115.5 135 149
LR 25 30 35
S 8 11 14 19
LA 45 70 90
LB 30 50 70
LC 38 60 80
LD ––
LE 3
LF 6 6.5 8
LG ––
LH 32 43 53
LN 26.5 46.5 ––
LZ 3.4 4.5 6
Keyway
LW 14 20 25
LK 12.5 18 22.5 22
KW 3h9 4h9 5h9 6h9
KH 3 4 5 6
RH 6.2 8.5 11 15.5
TP M3 x 6 (depth) M4 x 8 (depth) M5 x 10 (depth)
Mass (kg)Without brake 0.32 0.47 0.82 1.2 2.3
With brake 0.53 0.68 1.3 1.7 3.1
Minas A4 Series Servo DrivesB
Motor Specification
21
1KW – 5KW
AC200VMotor model MSMA 102P1 152P1 202P1 302P1 402P1 502P1
Applicable driverModel No. MDDDT5540 MEDDT7364 MFDDTA390 MFDDTB3A2
Frame symbol Frame D Frame E Frame F
Power supply capacity (kVA) 1.8 2.3 3.3 4.5 6.0 7.5
Rated output (W) 1000 1500 2000 3000 4000 5000
Rated torque (N • m) 3.18 4.77 6.36 9.54 12.6 15.8
Momentary max. peak torque (N • m) 9.5 14.3 19.1 28.6 37.9 47.6
Rated current (Arms*) 7.2 9.4 13.0 18.6 24.7 28.5
Max. current (Ao-p) 30 40 56 80 105 120
Regenerativebrake frequency(times/min) 1
Without option No limit 2 326
With external brake resistor
No limit 2
–– No limit 2
Rated rotational speed (r/min) 3000
Max. rotational speed (r/min) 5000 4500
Moment of inertiaof rotor(x10-4 kg • m2)
Without brake 1.69 2.59 3.46 6.77 12.7 17.8
With brake 1.88 2.84 3.81 7.45 14.1 19.7
Recommended moment of inertiaratio of the load and the rotor 3 Smaller then 15 times
Rotary encoder specifications 2500P/rIncremental
Resolution per single turn 10000
Protective enclosure rating IP65 (except shaft through hole and cable end connector)
Environment
Ambienttemperature 0°C to 40°C (free from freezing), Storage : -20°C to + 80°C
Ambient humidity 85%RH or lower (free from condensing)
Installationlocation Indoors (no direct sunlight), free from corrosive gas, inflammable gas, oil mist and dust
Altitude 1000m or lower
Vibrationresistance 49m/s2 or less
Mass (kg), ( ) representsholding brake type 4.5 (5.1) 5.1 (6.5) 6.5 (7.9) 9.3 (11.0) 12.9 (14.8) 17.3 (19.2)
Brake specifications (This brake will be released when it is energized. Do not use this for braking the motor in motion.)
Static friction torque (N • m) 4.9 7.8 11.8 16.1
Engaging time (ms) 50 80 110
Releasing time (ms) 4 15 (100) 50 (130)
Exciting current (DC) (A) 0.74 0.81 0.81 0.90
Releasing voltage DC2V or more
Exciting voltage DC 24 V 10%
Permissible load
During assembly
Radial loadP-direction (N) 686 980
Thrust loadA-direction (N) 392 588
Thrust loadB-direction (N) 490 686
During operation
Radial loadP-direction (N) 392 490 784
Thrust loadA-direction (N) 147 196 343
Thrust loadB-direction (N) 147 196 343
Minas A4 Series Servo DrivesB
For notes 1-4 see Page 22*rms= root mean square
22
Motor Characteristics 1kW to 5kW
5
0 1000 2000 3000 4000 5000
10
50
0 10 20 30 40
100��.5��
�3.18��
℃ ℃
7.5
0 1000 2000 3000�3500��
4000 5000
15
0 10 20 30 40
10085
50
�14.3��
�4.77��
MSMA152 1MSMA102 1
Notes:
1. Regenerative brake frequency represents the frequency of the motor's stops from the rated speed with deceleration without load.
• If the load is connected, frequency will be defined as 1/(m+1), where m=load moment of inertia/rotor moment of inertia.
• When the motor speed exceeds the rated speed, regenerative brake frequency is in inverse proportion to the square of (running speed/rated speed).
• Power supply voltage is AC230V (at 200V of the main voltage). If the supply voltage fluctuates, frequency is in inverse proportion to the square of (Running supply voltage/230) relative to the value in the table.
• When regeneration occurs continuously such cases as running speed frequently changes or vertical feeding, consult us or a dealer.
10
0 1000 2000 3000 4000 5000
20
0 10 20 30 40
100857050
�1�.1��
�6.36��
℃
MSMA202 1 MSMA302 1
15
0 1000 2000 3000 4000 5000
30
0 10 20 30 40
100�08550
28.6��
�.54��
℃
20
0 1000 2000 3000 4000 5000
40
0 10 20 30 40
100�08550
�37.���
�12.6��
℃
MSMA402 1
25
0 1000 2000 3000 4000 5000
50
0 10 20 30 40
100
7050
�47.6��
�15.8��
℃
MSMA502 1
2. If the effective torque is within the rated torque, there is no limit in generative brake.
3. Consult us or a dealer if the load moment of inertia exceeds the specified value.
4. Specified releasing time is obtained with the use of surge absorber for brake(Z15D151 by Ishizuka Electronic or equivalent).
( ) represents the actually measured value using a diode (200V, 1A or equivalent)
Minas A4 Series Servo DrivesB
*continuous torque,ambient temperature
*continuous torque,ambient temperature
*continuous torque,ambient temperature
*continuous torque,ambient temperature
*continuous torque,ambient temperature
running range (Torque limit setup: 300%)
running range (Torque limit setup: 200%)
running range (Torque limit setup: 200%)
radial load (P) direction thrust load (A, B) direction
Motor Dimensions
23
MSMA 1KW – 5KW (LOW INERTIA)
�W�� �W
��
��
�� ��
�� ��
����7
��
��
�S�6
�
��
Dimensions are subject to change without notice. Contact us or a dealer for the latest information.
MSMA series (low inertia)Motor output 1.0kW 1.5kW 2.0kW 3.0kW 4.0kW 5.0kW
Motor model MSMA 10 P1 15 P1 20 P1 30 P1 40 P1 50 P1
Rotary encoder specifications 2500P/r incremental
LLWithout brake 175 180 205 217 240 280
With brake 200 205 230 242 265 305
LR 55 55 65
S 19 22 24
LA 100 115 130/145 (slot) 145
LB 80 95 110
LC 90 100 120 130
LD 120 135 162 165
LE 3 6
LF 7 10 12
LG 84
LH 98 103 111 118
LZ 6.6 9
K e y w a y
LW 45 55
LK 42 41 51
KW 6h9 8h9
KH 6 7
RH 15.5 18 20
Mass (kg)Without brake 4.5 5.1 6.5 9.3 12.9 17.3
With brake 5.1 6.5 7.9 11.0 14.8 19.2
Connector/Plug specifications refer to Minas A4 Manual
Minas A4 Series Servo DrivesB
LL
LG
LR
LELF
ø L
B h
7
Sh6
LH
4- ø LZ
ø
LW
LKKW
RH
24
Option Select SoftwareSetup Support Software
SETUP SUPPORT SOFTWARE PANATERM®
FOR MINAS SERIES AC SERVO MOTOR & DRIVERPANATERM® assists users in setting parameters, monitoring®
control conditions, setup support, and analyzingoperation data on the PC screen when installed in a available personal computer and connected to the Mthrough the RS232 serial interface.
Graphic waveform display
Parameter
Monitor
BASIC FUNCTIONParameter setup• After a parameter is defined on the screen, it will be sent to the driver immediately.
• Once you register parameters you frequently use, they can be easily set up onthe screen.
MONITORING CONTROL CONDITIONSMonitor• Control conditions: control mode, velocity, torque, error and warning.
• Driver input signal.
• Load conditions: total count of command/feedback pulses, load ratio,regenerative resistor load ratio.
Alarm• Displays the numbers and contents of the current alarm
and up to 14 error events in the past.
• Clears the numbers and contents of the current alarmand up to 14 error events in the past.
SETUPAuto tuning• Gain adjustment and inertia ratio measurement.
Graphic waveform display
• The graphic display shows command velocity, actual velocity, torque,and error waveforms.
Absolute encoder setup
• Clears absolute encoder at the origin.
• Displays single revolution/multirevolution data.
• Displays absolute encoder status.
ANALYSIS OF MECHANICALPERATION DATA
Frequency analysis• Measures frequency characteristics of the machine, and displays Bode diagram.
C
Û
Standardized access to drive/motion specifics to harmonize the access for Motion Control across different platforms during development, installation and maintenance based on the IEC 61131-3 environment.
ADVANTAGES OF PLC PROGRAMS USING THE MOTION CONTROL LIBRARY COMPLIANT WITH THE PLCopen STANDARD:
• Simple – Easy programming and installation, even for complex applications
• Efficient – In the number of function blocks and in design and understanding
• Consistent – Compliant with the IEC 61131-3 PLC programming standard
• Universal – Hardware-independent
• Flexible – Add hardware or expand range of application at any time
• Complete – Comprehensive product line solves typical positioning applications easily
MC_MOVEABSOLUTESingle-axis motion to a specified absolute position.
1) If executed, the current motion is briefly interrupted due to hardware reasons.
MC_HOMESingle-axis motion to the home position.
MC_MOVEVELOCITY Single-axis motion at a specified velocity.
MC_MOVESUPERIMPOSED1)Superimposes a relative motion a running singleaxis motion.
MC_MOVEADDITIVE1)Adds a relative motion to a single axis motion. The distance is added to the target position of the previously executed FB.
MC_MOVERELATIVESingle-axis motion to a specified distance relative to the actual position.
Panasonic´s Motion Control Library is designed to save programming time with a sophisticated yet user-friendly software solution. Our library includes function blocks programmed according to PLCopen´s specification.
Motion Control Library for FPWIN Pro
25
SoftwareC
26
Motion Control Library for FPWIN Pro
SoftwareC
PLCopen, an independent international organization, aims to harmonise access across platforms during development, installation and maintenance based on the IEC61131-3 environment.
MC_STOPStops a single-axis motion by a specified modus (ramp to stop, emergency stop).
PROGRAM, LADDER DIAGRAM BODY
FFWD FWD DWELL REV
v
s
t
t
FF F
REV
Drilling setupTiming diagram
MC_READSTATUSOutputs the motion status of a single axis.
MC_READACTUALPOSITIONOutputs the actual position of a single axis.
MC_RESETResets all internal errors of a single axis after a stop due to an error.
MC_POSITIONPROFILESingle-axis motion according to a time-position motion profile.
MC_VELOCITYPROFILESingle-axis motion profile according to a time-velocity motion profile.
EXAMPLE FOR CONSECUTIVE MOVEMENT IN A DRILLING APPLICATION
See also: http://www.plcopen.org/MC_Certification/Panasonic/shortform_statement_Panasonic.htm
Multiple-Axis Function Blocks
27
SoftwareC
MC_CAMTABLESELECTSelects the CAM table by setting the pointer to the relevant table.
MC_CAMINEngages the CAM.
MC_CAMOUTDisengages the slave from the master axis immediately.
MC_GEARINSpecifies a ratio for the velocities of the master to slave axis.
MC_GEAROUTDisengages the slave from the master axis.
Motion Control Library NCL-MC-LIB D
20062006
28
AccessoriesEncoder Cables
�
(14)
(11.8)
(4) (4)
MFECA0 * * 0EAM
�
�37.3
MFECA0 * * 0ESD
PNPowerrange
Length IP classDrag chain
usagePowersupply
Additionalinformation
MFECA0010EAM 50 - 750W 1m possible 1/3~200VAC
MFECA0020EAM 50 - 750W 2m possible 1/3~200VAC
MFECA0030EAM 50 - 750W 3m possible 1/3~200VAC
MFECA0050EAM 50 - 750W 5m possible 1/3~200VAC
MFECA0100EAM 50 - 750W 10m possible 1/3~200VAC
MFECA0020EAB 50 - 750W 2m IP67 possible 1/3~200VAC high qualityconnector
MFECA0030EAB 50 - 750W 3m IP67 possible 1/3~200VAC high qualityconnector
MFECA0040EAB 50 - 750W 4m IP67 possible 1/3~200VAC high qualityconnector
MFECA0050EAB 50 - 750W 5m IP67 possible 1/3~200VAC high qualityconnector
MFECA0100EAB 50 - 750W 10m IP67 possible 1/3~200VAC high qualityconnector
MFECA0150EAB 50 - 750W 15m IP67 possible 1/3~200VAC high qualityconnector
MFECA0030ESD 1 - 5kW 3m IP67 possible 1/3~200VAC Canon plug
MFECA0050ESD 1 - 5kW 5m IP67 possible 1/3~200VAC Canon plug
MFECA0100ESD 1 - 5kW 10m IP67 possible 1/3~200VAC Canon plug
AccessoriesMotor and Brake Cables
29
MOTOR CABLES
(50) (50)�(�11)
(10.0)
(12.0)
(4) (4)
A0 * * 0EED
(50)�
(�12.5)
�37.3
MFMCD0 * * 2ECD
BRAKE CABLE
(��.8)
(40) (50)�
(5.6)
(12.0)
(10.0)
MFMCB0 * * 0GET
� (50)
(50)
(�12.5)
�37.3
(��.8)
MFMCA0 * * 2FCD
MOTOR CABLE (WITH BRAKE)
PNPowerrange
Length IP classDrag chain
usagePowersupply
Additionalinformation
Motor cables
MFMCD0102ECT 2kW 10m IP67 possible 1~230VAC
MFMCA0033ECT 3 - 5kW 3m IP67 possible 1~230VAC
MFMCA0053ECT 3 - 5kW 5m IP67 possible 1~230VAC
MFMCA0103ECT 3 - 5kW 10m IP67 possible 1~230VAC
MFMCA0032FCD 1 - 1.5kW 3m IP67 possible 1~230VAC For motors withholding brake
MFMCA0052FCD 1 - 1.5kW 5m IP67 possible 1~230VAC For motors withholding brake
MFMCA0102FCD 1 - 1.5kW 10m IP67 possible 1~230VAC For motors withholding brake
MFMCA0032FCT 2kW 3m IP67 possible 1~230VAC For motors withholding brake
MFMCA0052FCT 2kW 5m IP67 possible 1~230VAC For motors withholding brake
MFMCA0102FCT 2kW 10m IP67 possible 1~230VAC For motors withholding brake
MFMCA0033FCT 3 - 5kW 3m IP67 possible 1~230VAC For motors withholding brake
MFMCA0053FCT 3 - 5kW 5m IP67 possible 1~230VAC For motors withholding brake
MFMCA0103FCT 3 - 5kW 10m IP67 possible 1~230VAC For motors withholding brake
Brake cables
MFMCB0050GETS 30 - 750W 5m possible 1/3~200VAC
MFMCB0100GETS 30 - 750W 10m possible 1/3~200VAC
PNPowerrange
Length IP classDrag chain
usagePowersupply
Additionalinformation
Motor cables
MFMCA0010EED 50 - 750W 1m possible 1~230VAC
MFMCA0020EED 50 - 750W 2m possible 1~230VAC
MFMCA0030EED 50 - 750W 3m possible 1~230VAC
MFMCA0050EED 50 - 750W 5m possible 1~230VAC
MFMCA0100EED 50 - 750W 10m possible 1~230VAC
MFMCA0020EBD 50 - 750 W 2m IP67 possible 1~230VAC High qualityconnector
MFMCA0030EBD 50 - 750W 3m IP67 possible 1~230VAC High qualityconnector
MFMCA0040EBD 50 - 750W 4m IP67 possible 1~230VAC High qualityconnector
MFMCA0050EBD 50 - 750W 5m IP67 possible 1~230VAC High qualityconnector
MFMCA0100EBD 50 - 750 W 10m IP67 possible 1~230VAC High qualityconnector
MFMCA0150EBD 50 - 750 W 15m IP67 possible 1~230VAC High qualityconnector
MFMCD0032ECD 1 - 1.5kW 3m IP67 possible 1~230VAC
MFMCD0052ECD 1 - 1.5kW 5m IP67 possible 1~230VAC
MFMCD0102ECD 1 - 1.5kW 10m IP67 possible 1~230VAC
MFMCD0032ECT 2kW 3m IP67 possible 1~230VAC
MFMCD0052ECT 2kW 5m IP67 possible 1~230VAC
30
AccessoriesDirect Connection to FP-Series PLCs
Product No. Description Number of axes Power range Length Connectors
DVOP0980W-1 FPG NPN to CN I/F 1 0.03 - 5kW 1m 50 pin Molex to 2x10 pin MIL
DVOP0981W-1 FPG NPN to CN I/F 2 0.03 - 5kW 1m 2x50 pin Molex to 2x10 pin MIL
DVOP0982W-1 FPG PNP to CN I/F 1 0.03 - 5kW 1m 50 pin Molex to 2X10 pin MIL
DVOP0983W-1 FPG PNP to CN I/F 2 0.03 - 5kW 1m 2x50 pin Molex to 2x10 pin MIL
DVOP0984W-1 FPG NPN to CN I/F, with TLC-signal 2 0.03 - 5kW 1m 50 pin Molex to 2X10 pin MIL, with TLC signal
DVOP0985W-1 FPG/ FP2 Positioning Units 2 0.03 - 5kW 1m 50 pin Molex to 1x40 pin MIL
PLC CONNECTION CABLE
50-pin Molex connector attached to the Panasonic servo driver In/out connectors for the PLC FP (Sigma)(not used inputs/outputs can be used for other purposes)
DVOP0980W-1DVOP0982W-1
DVOP0983W-1DVOP0984W-1
DVOP0981W-1
AccessoriesOther Cables, Connectors, Brake Resistors, Filters
31
PNPowerrange
LengthPowersupply
Additionalinformation
Brake resitors
BWD250100 30 - 750W 1~230VAC 100 Ohm/100W
BWD600027 1 - 5kW 1~230VAC 27Ohm/240W
Connector kits and connectors
DVOP4380 50 - 750W 1~230VAC Connector kit for motors and encoder
DVOP4310 1 - 2kW 1~230VAC Connector kit for motors and encoder
DVOP4320 3 - 5kW 1~230VAC Connector kit for motors and encoder
DVOP4330 1 - 2kW 1~230VAC Connector kit for motors and encoder
DVOP4340 3 - 5kW 1~230VAC Connector kit for motors and encoder
DVOP0985W-1 (see Page 30)
PNPowerrange
LengthPowersupply
Additionalinformation
Communication cables
DVOP1960 0.03 - 5kW 2m 1/3~200VAC
RS232Ccommunication 9 pin Sub-D to MINI-DIN 8 pin
DVOP1972 0.03 - 5kW 1m 1/3~200VAC
RS485communication MINI-DIN 8 pinto MINI-DIN 8 pin
EMC Line Filter
FS21238607 50 - 750W 1~230VAC 1-phase EMC filter 250VAC, 50/60 Hz, 6A
FN2071N1606 1 - 3.5 kW 1~230VAC 1-phase EMC filter 250VAC, 50/60Hz, 16A
DIRECT CONNECTION OF POSITIONING UNITS
HIGH QUALITY CONNECTORS
Copyright © 2006 • Printed in Germany4152 eu en 09/06
Asia Pacific China JapanNorth America Europe
Global Network
Please contact our Global Sales Companies in:Europe
Headquarters Panasonic Electric Works Europe AG Rudolf-Diesel-Ring 2, 83607 Holzkirchen, Tel. (08024) 648-0, Fax (08024) 648-111, www.panasonic-electric-works.comAustria Panasonic Electric Works Austria GmbH Josef Madersperger Str. 2, 2362 Biedermannsdorf, Tel. (0 22 36) 2 68 46, Fax (0 22 36) 4 61 33, www.panasonic-electric-works.at
PEW Electronic Materials Europe GmbH Ennshafenstraße 9, 4470 Enns, Tel. (0 72 23) 8 83, Fax (0 72 23) 8 83 33, www.panasonic-electronic-materials.comBenelux Panasonic Electric Works
Sales Western Europe B.V. De Rijn 4, (Postbus 211), 5684 PJ Best, (5680 AE Best), Netherlands, Tel. (0499) 372727, Fax (0499) 372185, www.panasonic-electric-works.nlCzech Republic Panasonic Electric Works Czech s.r.o. Prumtyslová 1, 34815 Planá, Tel. 374 799 990, Fax 374 799 999, www.panasonic-electric-works.czFrance Panasonic Electric Works
Sales Western Europe B.V. French Branch Office, B.P. 44, 91371 Verrières le Buisson CEDEX, Tél. 01 60135757, Fax 01 60135758, www.panasonic-electric-works.frGermany Panasonic Electric Works Deutschland GmbH Rudolf-Diesel-Ring 2, 83607 Holzkirchen, Tel. (08024) 648-0, Fax (08024) 648-555, www.panasonic-electric-works.deIreland Panasonic Electric Works UK Ltd. Dublin, Tel. (01) 4600969, Fax (01) 4601131, www.panasonic-electric-works.co.ukItaly Panasonic Electric Works Italia s.r.l. Via del Commercio 3-5 (Z.I. Ferlina), 37012 Bussolengo (VR), Tel. (045) 6752711, Fax (045) 6700444, www.panasonic-electric-works.it
PEW Building Materials Europe s.r.l. Piazza della Repubblica 24, 20154 Milano (MI), Tel. (02) 29005391, Fax (02) 29003466, www.panasonic-building-materials.comNordic Countries Panasonic Electric Works Nordic AB Sjöängsvägen 10, 19272 Sollentuna, Sweden, Tel. (08) 59476680, Fax (08) 59476690, www.panasonic-electric-works.se
PEW Fire & Security Technology Europe AB Citadellsvägen 23, 21118 Malmö, Tel. (040) 6977000, Fax (040) 6977099, www.panasonic-fire-security.comPortugal Panasonic Electric Works España S.A. Portuguese Branch Office, Avda Adelino Amaro da Costa 728 R/C J, 2750-277 Cascais, Tel. (21) 4812520, Fax (21) 4812529Spain Panasonic Electric Works España S.A. Barajas Park, San Severo 20, 28042 Madrid, Tel. (91) 3293875, Fax (91) 3292976, www.panasonic-electric-works.esSwitzerland Panasonic Electric Works Schweiz AG Grundstrasse 8, 6343 Rotkreuz, Tel. (041) 7997050, Fax (041) 7997055, www.panasonic-electric-works.chUnited Kingdom Panasonic Electric Works UK Ltd. Sunrise Parkway, Linford Wood, Milton Keynes, MK14 6LF, Tel. (01908) 231555, Fax (01908) 231599, www.panasonic-electric-works.co.uk
North & South America
USA PEW Corporation of America 629 Central Avenue, New Providence, N.J. 07974, Tel. 1-908-464-3550, Fax 1-908-464-8513, www.pewa.panasonic.com
Asia Pacific / China / Japan
China Panasonic Electric Works (China) Co., Ltd. Level 2, Tower W3, The Towers Oriental Plaza, No. 2, East Chang An Ave., Dong Cheng District, Beijing 100738, Tel. (010) 8518-5988,Fax (010) 8518-1297
Hong Kong Panasonic Electric Works RM1205-9, 12/F, Tower 2, The Gateway, 25 Canton Road, Tsimshatsui, Kowloon, Hong Kong, Tel. (0852) 2956-3118, Fax (0852) 2956-0398(Hong Kong) Co., Ltd.
Japan Matsushita Electric Works, Ltd. 1048 Kadoma, Kadoma-shi, Osaka 571-8686, Japan, Tel. (06) 6908-1050, Fax (06) 6908-5781, www.mew.co.jp/e-acg/Singapore Panasonic Electric Works Asia Pacific Pte. Ltd. 101 Thomson Road, #25-03/05, United Square, Singapore 307591, Tel. (06255) 5473, Fax (06253) 5689
Panasonic Electric Works
Dystrybutor w Polsce: AUTOMATECH Sp.z o.o. http//:www.automatech.pl email: [email protected]