Minor connectors
Rests & Rest seats
Presented by:
Dr. Mujtaba Ashraf
MDS II
Dept of Prosthodontics
Dr Mujtaba 2
Contents:
Minor Connectors
Functions
Form and location
Tissue stops Rests and Rest Seats
Role of Rests in Control of Prosthesis Movement
Form of the Occlusal Rest and Rest Seat
Lingual Rests on Canines and Incisor Teeth
Incisal Rests and Rest Seats
Dr Mujtaba 3
Minor Connectors
Dr Mujtaba 4
Definition
The connecting link between the major connector or base of a partial removable dental prosthesis and the other units of the prosthesis, such as the clasp assembly, indirect retainers, occlusal rests, or cingulum rests. –GPT8
Dr Mujtaba 5
Connects components to the major
connector
Direct retainer
Indirect retainer
Denture base
Dr Mujtaba 6
Functions of Minor Connectors
Unification and rigidity Transfers functional stress to the abutment teeth. This
is a prosthesis-to-abutment function of the minor connector.
Transfers the effects of the retainers, rests, and stabilizing components throughout the prosthesis. This is an abutment- to-prosthesis function of the minor connector.
Dr Mujtaba 7
Form and location
Sufficiently bulky to be rigid Should be located in the
embrasure The deepest part of embrasure
should be blocked
Dr Mujtaba 8
Should be thickest towards lingual surface and tapering towards the contact area.
Dr Mujtaba 9
Types of minor connectors
Minor connectors that join clasp assemblies to major connectors
Minor connectors that join indirect retainers or auxiliary rests to major connectors
-Stewart
Dr Mujtaba 10
Minor connectors that join denture bases to major connectors
Minor connectors that serve as approach arms for vertical projection or bar-type clasps
-Stewart
Types of minor connectors
Dr Mujtaba 11
Minor connectors that join clasp assemblies to major connectors Join clasp assemblies to major connectors must be
rigid, because they support the active components of the removable partial denture, the retentive clasps.
Dr Mujtaba 12
Support the rests, which prevent vertical movement of a prosthesis toward the underlying tissues.These minor connectors should be broad buccolingually, but thin mesiodistally.
Dr Mujtaba 13
A minor connector should be positioned in the associated lingual embrasure. This results in a sufficient bulk of metal without encroaching on the tongue space.
Dr Mujtaba 14
Minor connectors that join indirect retainers or auxiliary rests to major connectors
These minor connectors should form right angles with the corresponding major connectors, but junctions should be gently curved to prevent stress concentration
Dr Mujtaba 15
Minor connectors that join denture bases to major connectors
These minor connectors must be strong enough to anchor a denture base to the removable partial denture framework.
They must be rigid enough to resist fracture and displacement.
These components must provide minimal interference with the arrangement of artificial teeth.
Dr Mujtaba 16
In maxillary distal extension bases, it must extent to cover the tuberosity, andIn mandibular distal extension bases it should extend two-third the length of residual ridges,
Dr Mujtaba 17
Minor connectors that join the denture base to the major connector may be described as follows
Open/ Lattice construction
Mesh construction
Bead, wire, or nail-head components on a metal
base
Dr Mujtaba 18
Open/ Lattice construction
Open construction consists of longitudinal and transverse struts that form a ladder-like network.
Dr Mujtaba 19
Placement of the longitudinal and transverse struts is a critical factor in prosthetic tooth arrangement.
In the mandibular arch, one longitudinal strut should be positioned buccal to the crest of the ridge and the other lingual to the ridge crest.
In the maxillary arch, one longitudinal strut should be positioned buccal to the ridge crest.
The border of the major connector generally will act as the second longitudinal strut.
Dr Mujtaba 20
Positioning of a longitudinal strut along the crest of the ridge must be avoided. This not only interferes with the placement of artificial teeth, but also leads to the denture base to fracture.
Transverse struts also must be positioned to facilitate the placement of artificial teeth.
Ideally, transverse struts should be designed to pass between the necks of the artificial teeth. This aids in tooth arrangement and often results in improved esthetics.
Dr Mujtaba 21
Advantages of open construction
Used for multiple teeth replacement Provides strongest attachment of acrylic resin Facilitates rebasing and relining
Dr Mujtaba 22
Mesh construction
A mesh minor connector may be compared to a rigid metallic screen.
Channels that pass through the connector are intended to permit acrylic resin penetration.
This allows resin encirclement of the minor connector and mechanical retention of the denture base.
Dr Mujtaba 23
Drawback
• During the packing of acrylic resin, increased pressure is needed to force resin through the small holes in the minor connector.
• Insufficient packing pressure may result in inadequate resin penetration and a weak attachment to the framework.
• Also interfere with the arrangement of prosthetic teeth.
The smaller the openings in this minor connector, the weaker the attachment.
Dr Mujtaba 24
Bead, wire or nail-head construction
Bead, nail-head, or wire components are often used in conjunction with metal denture bases.
Dr Mujtaba 25
Its is indicated on short-span, tooth supported with well healed ridges.
The primary advantage of a metal base is related toimproved hygiene and thermal stimulation.
DisadvantagesInclude difficulty in adjusting and relining cast metal bases.Furthermore, the attachment of resin is relatively weak.
Dr Mujtaba 26
Tissue stop
Used in all distal extension partial dentures using lattice work or mesh retention.
Provide stability and prevent distortion to framework during packing of acrylic resin.
Engage buccal and lingual slopes for stability.
Dr Mujtaba 27
Made by removing approximately 2 square mm of the relief wax used to create space beneath the lattice work or mesh from the point where the posterior end of minor connector crosses the centre of the ridge.During waxing this little depression is waxed as a projection of latticework or mesh.
Dr Mujtaba 28
Relief
Mechanical retention of denture base resinAllows the acrylic resin to flow under the constructionRelief wax is placed in the edentulous areas of 1 mm
Dr Mujtaba 29
Finish Lines
The planned junction of different materials. (GPT-8)
In RPDs it denotes the junction of acrylic resin denture bas and metal major connector.
InternalExternal
If they are located on the outer surfaces of major connectors, they are called external finish lines.If they are positioned on the inner or tissue surfaces, they are termed internal finish lines.
Dr Mujtaba 30
Internal finish lines are formed as a result of relief wax placed on the edentulous ridges of a master cast prior to duplication.The relief wax (24 to 26 gauge) creates an elevated area on the resultant refractory cast. The margins of the relief wax establish internal finish lines in the completed metal framework. The margins of the relief wax should be sharp and well defined.
Dr Mujtaba 31
External finish lines also must be sharp and should be slightly undercut to help lock the acrylic resin to the major connector.The internal angle formed at the junction of the major or and minor connectors should be less than 90 degrees.
Dr Mujtaba 32
When viewed from an occlusal perspective, the external finish line should follow an arc established by the lingual surfaces of the remaining teeth.This permits the development of contours that are not irritating to the patient.
The contour of the external finish line should be consistent with the contours of the major connector. Transition from the external finish line to a denture base should be smooth and flowing.
Dr Mujtaba 33
Approach Arm Minor connector This serves as an approach arm for a bar clasp, supports
a direct retainer and engages an undercut from the gingival margin.
Only minor connector that is not required to be rigid. Should be smooth, even and taper from its origin to its
terminus.
Dr Mujtaba 34
Rests and Rest Seats
Dr Mujtaba 35
Definition
Rest: A rigid extension of a fixed or removable dental prosthesis that prevents movement toward the mucosa and transmits functional forces to the teeth or dental implant. GPT-8
The components of a removable partial denture that transfer forces down the long axes of the abutment teeth are called rests. -Stewart
Rest seat: The prepared recess in a tooth or restoration created to receive the occlusal, incisal, cingulum or lingual rest. GPT-8
Dr Mujtaba 36
Functions Support: Prevent movement of prosthesis toward the
tissues. Force transfer: To direct the forces of mastication
parallel to the long axis of the abutment tooth.
Occlusal rests and rest seats, Albert Seiden, JPD 1958
Dr Mujtaba 37
To act as a stop, preventing injury and over displacement of the soft tissues under partial denture bases.
To maintain the clasp, which is usually attached to the occlusal rest, in its properly surveyed position.
To function as an indirect retainer in a free-end denture base partial denture.
Occlusal rests and rest seats, Albert Seiden, JPD 1958
Dr Mujtaba 38
Functions
To help maintain the partial denture in position. This is done when the rests contact or occlude with opposing teeth during mastication and deglutition.
To transmit to the abutment teeth some of the lateral forces applied to the partial denture during mastication.
To prevent impaction of food between the clasp and the proximal surface of the abutment tooth.
Occlusal rests and rest seats, Albert Seiden, JPD 1958
Dr Mujtaba 39
Functions
To close a small space between teeth by bridging that space with occlusal rests.
To build up an abutment tooth with a large occlusal onlay rest. This is necessary if there has been a loss of occlusal contact due to the drifting of teeth
To act as a rigid reciprocal arm of a retaining clasp. This function is most pronounced when the rest is set into a tapered box-lock seat in a gold crown or inlay.
To prevent extrusion, of abutment teeth.
Occlusal rests and rest seats, Albert Seiden, JPD 1958
Dr Mujtaba 40
Classification
Based on Relation to Direct Retainer Primary rests Secondary rests
Based on Area of Placement Occlusal rests Lingual or cingulum rests Incisal rests
Dr Mujtaba 41
Primary rest A rest that is part of a retentive clasp assembly is referred to as a
primary rest. Prevent vertical movement of a prosthesis toward the tissues and also
help transmit applied forces to the supporting teeth. Should be shallow and saucer shaped, and should function as ball-
and-socket joint. This geometry permits dissipation of potentially harmful lateral forces.
Dr Mujtaba 42
Auxiliary or secondary rests A rest that is responsible for additional support or indirect
retention is called an auxiliary rest or secondary rest. Are used as indirect retainers in extension base removable partial
dentures (Class I, Class II, and long-span Class IV applications). These rests are placed anterior or posterior to the axis of rotation
to prevent the extension bases from lifting away from the underlying ridges.
Dr Mujtaba 43
Occlusal rest
A rigid extension of a removable dental prosthesis that contacts the occlusal surface of a tooth or restoration, the occlusal surface of which may have been prepared to receive it. –GPT8
Dr Mujtaba 44
Form of the Occlusal Restand Rest Seat
The outline form of an occlusal rest seat should be a rounded triangular shape with the apex toward the center of the occlusal surface.
Dr Mujtaba 45
It should be as long as it is wide, and the base of the triangular shape (at the marginal ridge) should be at least 2.5 mm for both molars and premolars.
Rest seats of smaller dimensions do not provide an adequate bulk of metal for rests, especially if the rest is contoured to restore the occlusal morphology of the abutment tooth.
Dr Mujtaba 46
The marginal ridge of the abutment tooth at the site of the rest seat must be lowered to permit a sufficient bulk of metal for strength and rigidity of the rest and the minor connector. This means that a reduction of the marginal ridge of approximately 1.5 mm is usually necessary.
Dr Mujtaba 47
The floor of the occlusal rest seat should be apical to the marginal ridge and the occlusal surface and should be concave, or spoon shaped.Caution should be exercised in preparing a rest seat to avoid creating sharp edges or line angles in the preparation.
Dr Mujtaba 48
The angle formed by the occlusal rest and the vertical minor connector from which it originates should be less than 90 degrees. Only in this way can the occlusal forces be directed along the long axis of the abutment tooth.
Dr Mujtaba 49
An angle greater than 90 degrees fails to transmit occlusal forces along the supporting vertical axis of the abutment tooth. This also permits slippage of the prosthesis away from the abutment, which can result in orthodontic-like forces being applied to an inclined plane on the abutment, with possible tooth movement.
Dr Mujtaba 50
An occlusal rest seat should occupy one third to one half the mesiodistal diameter of the abutment and approximately one half the buccolingual width of the tooth measured from cusp tip to cusp tip.
Dr Mujtaba 51
Lingual or cingulum rests
A metallic extension of a partial removable dental prosthesis framework that fits into a prepared depression within an abutment tooth’s lingual surface. –GPT8
Dr Mujtaba 52
Lingual or cingulum rests are used primarily on maxillary canines. The normal morphology of a maxillary canine permits preparation of a satisfactory rest seat with minimal tooth reduction.
Dr Mujtaba 53
The thickness of enamel on the lingual surface of a mandibular canine rarely allows a lingual rest to be used.Lingual rests on incisors are also rare.
The main indication for their use is missing canines. In this instance, multiple incisors should receive lingual rests to distribute the stresses over a number of teeth because a single incisor seldom offers adequate support.
Dr Mujtaba 54
A lingual rest is located closer to the rotational center of the supporting tooth and does not tend to tip the tooth.
Dr Mujtaba 55
Form
Outline form of lingual rest is half-moon shaped, making a smooth curve from one marginal ridge to the other, crossing the centre of the tooth above the cingulum with deepest point over the cingulum.
Dr Mujtaba 56
The rest is is V-shaped and has two inclinesLabial incline and lingual inclineLabial incline is parallel to the labial surface of toothLingual incline begins at the top of cingulum and converges labiogingivally towards centre of the tooth, to meet the labial incline at the apex of rest seat.
Dr Mujtaba 57
The mesiodistal length of the preparation should be a minimum of 2.5 to 3 mm,labiolingual width about 2 mm,incisal-apical depth a minimum of 1.5 mm.
Dr Mujtaba 58
Round Lingual Rest Seat Form
Mesial of the canine teeth when typical cingulum rest contraindicated Large restoration Lack of clearance with the opposing teeth Poor cingulum
Dr Mujtaba 59
Spoon shaped, similar to occlusal rest seatMore difficult due to the incline of the lingual surface Easily incorporated into crowns
Dr Mujtaba 60
Lingual rest seats on cast restorations When a crown is to be placed on an anterior tooth and
a rest seat is required, the rest seat should be placed in the wax pattern
The floor of the rest seat is readily carved to be the most apical portion of the preparation. A saddle-like shape, which provides a positive rest seat located favorably in relation to the long axis of the tooth, is formed.
Dr Mujtaba 61
The framework of the denture is made to fill out the continuity of the lingual surface so that the tongue contacts a smooth surface without the patient being conscious of bulk or irregularities.The lingual rest may be placed on the lingual surface of a cast veneer crown a three-quarter crown, an inlay, a laminate veneer, a composite restoration.
Dr Mujtaba 62
Incisal rests Incisal rests are placed at the incisal angles of anterior
teeth and on prepared rest seats. Less desirable than lingual rests and rest seats for
anterior teeth. Nevertheless, they may be used successfully if abutments are sound and cast restorations are not indicated.
Dr Mujtaba 63
The incisal rest may be used on a canine abutment in either arch, it is more applicable to the mandibular canine. This type of rest provides definite support with relatively little loss of tooth structure and little display of metal.Esthetically it is preferable to the three-quarter crown.
Dr Mujtaba 64
Three views of an incisal rest seat preparation on the mandibular canine adjacent to a modification space.The labial view demonstrates inclination of the floor of the rest seat, which allows forces to be directed along the long axis of the tooth as nearly as possible.
Dr Mujtaba 65
The proximal edge of the rest seat is rounded rather than straight. The lingual view shows that all borders of the restseat are rounded to avoid sharp line angles.It is especially important to avoid a line angle at the junction of the axial wall of the preparation and the floor of the rest seat
Dr Mujtaba 66
Should appear as a small , V-shaped notch located approximately 1.5 to 2.0 mm from the proximal-incisal angle of the tooth.
The deepest part of the preparation should be toward the center of the tooth mesiodistally.
The notch should be rounded and should extend slightly onto the facial surface to provide a positive seat for the rest.
A=2mmB= 1.5mm
Dr Mujtaba 67
References
Stewart’s clinical removable partial prosthodontics, 3rd ed McCrackens removable partial prosthodontics, 12th ed Removable partial dentures-A Practitioners’ Manual, Olcay
Şakar Seidin A. Occlusal rests and rest seats. J Prosthet Dent
1958;8: 431-440. Dunny JA, King CIE. Minor connector design for anterior
acrylic resin bases: A preliminary study. J Prosthet Dent 1975;34:496-502.
Dr Mujtaba 68