#82871 BELT FOR DREMEL TABLE SAWINSTRUCTIONS FOR INSTALLATION
AND ADJUSTMENT
BELT REMOVAL/INSTALLATION
Unplug the saw from electrical outlet and removeany attachments from the table top. Lower bladefully. Turn saw upside down, resting it on its top.“Walk off” worn belt from the non-flanged arborpulley while rotating the assembly. Place the newbelt onto the flanged motor pulley first and thenproceed to “walk on” the new belt.
BELT ADJUSTMENT
If the new belt is too loose or too tight wheninstalled, adjust the motor position for optimum belttension as follows: Locate the two 1/8” Allen screwswhich mount the motor, and loosen just enough toallow the motor to be moved. Position motor so thatbelt can rotate freely around the pulleys withoutslipping, then tighten the screws.
Note: When moving the motor, it is essential that themotor remains aligned with the arbor assembly sothat the belt will track straight and not rub against theflanges of the motor pulley, or run off of the arborpulley. Belt deflection under moderate fingerpressure should be approx. 3/8” between the pulleys.
MM051508
T H E S M A L L T O O L S P E C I A L I S T S340 Snyder Avenue, Berkeley Heights, NJ 07922
Tech Support: 908-464-1094, weekdays, 1pm to 5pm ETwww.micromark.com [email protected]
#82871 BELT FOR DREMEL TABLE SAWINSTRUCTIONS FOR INSTALLATION
AND ADJUSTMENT
BELT REMOVAL/INSTALLATION
Unplug the saw from electrical outlet and removeany attachments from the table top. Lower bladefully. Turn saw upside down, resting it on its top.“Walk off” worn belt from the non-flanged arborpulley while rotating the assembly. Place the newbelt onto the flanged motor pulley first and thenproceed to “walk on” the new belt.
BELT ADJUSTMENT
If the new belt is too loose or too tight wheninstalled, adjust the motor position for optimum belttension as follows: Locate the two 1/8” Allen screwswhich mount the motor, and loosen just enough toallow the motor to be moved. Position motor so thatbelt can rotate freely around the pulleys withoutslipping, then tighten the screws.
Note: When moving the motor, it is essential that themotor remains aligned with the arbor assembly sothat the belt will track straight and not rub against theflanges of the motor pulley, or run off of the arborpulley. Belt deflection under moderate fingerpressure should be approx. 3/8” between the pulleys.
MM051508
T H E S M A L L T O O L S P E C I A L I S T S340 Snyder Avenue, Berkeley Heights, NJ 07922
Tech Support: 908-464-1094, weekdays, 1pm to 5pm ETwww.micromark.com [email protected]
#82871 BELT FOR DREMEL TABLE SAWINSTRUCTIONS FOR INSTALLATION
AND ADJUSTMENT
BELT REMOVAL/INSTALLATION
Unplug the saw from electrical outlet and removeany attachments from the table top. Lower bladefully. Turn saw upside down, resting it on its top.“Walk off” worn belt from the non-flanged arborpulley while rotating the assembly. Place the newbelt onto the flanged motor pulley first and thenproceed to “walk on” the new belt.
BELT ADJUSTMENT
If the new belt is too loose or too tight wheninstalled, adjust the motor position for optimum belttension as follows: Locate the two 1/8” Allen screwswhich mount the motor, and loosen just enough toallow the motor to be moved. Position motor so thatbelt can rotate freely around the pulleys withoutslipping, then tighten the screws.
Note: When moving the motor, it is essential that themotor remains aligned with the arbor assembly sothat the belt will track straight and not rub against theflanges of the motor pulley, or run off of the arborpulley. Belt deflection under moderate fingerpressure should be approx. 3/8” between the pulleys.
MM051508
T H E S M A L L T O O L S P E C I A L I S T S340 Snyder Avenue, Berkeley Heights, NJ 07922
Tech Support: 908-464-1094, weekdays, 1pm to 5pm ETwww.micromark.com [email protected]
Recommended
