8/4/2019 LG Plasma Monitor
1/36
PLASMAMONITOROWNERS MANUAL
Please read this owners manual thoroughly before operatingthe Monitor.Retain it for future reference.Record model number and serial number of the Monitor.See the label attached on the back of the Monitor and relatethis information to your dealer if you ever require service.
Model Number :Serial Number :
MODELS:MP-42PZ44/44H/45M/45V
MP-42PZ44A/44HA/45MA/45VA
MP-42PZ44B/44HB/45MB/45VB
MP-42PZ44K/44HK/45MK/45VK
MP-42PZ44R/44HR/45MR/45VR
MP-42PZ44S/44HS/45MS/45VS
MP-42PZ90/90H/91M/91V
MP-42PZ90A/90HA/91MA/91VA
MP-42PZ90B/90HB/91MB/91VB
MP-42PZ90K/90HK/91MK/91VK
MP-42PZ90R/90HR/45MR/91VR
MP-42PZ90S/90HS/91MS/91VS
P/NO : 3828VA0415A (RF03GA)a
8/4/2019 LG Plasma Monitor
2/36
Safety Instructions
Safety InstructionsSafety Instructions
1. Do not place the Monitor in direct sunlight or near
heat sources such as heat registers, stove and soon.
This may cause a fire.
2. Do not use the Monitor in damp place such as abathroom or any place where it is likely to getwet.
This may cause a fire or could give an electric shock.
3. Bend antenna cable between inside and outside
building to prevent rain from flowing in.This may cause water damaged inside the Monitor and couldgive an electric shock.
4. Earth wire should be connected.
- If the earth wire is not connected, there is possible a dangerof electric shock caused by the current leakage.
- If grounding methods are not possible, a separate circuitbreaker should be employed and installed by a qualifiedelectrician.
- Do not connect ground to telephone wires, lightning rods or
gas pipe.
6. Do not insert any object into
This may cause a fire or could give
7. Do not place heavy objects o
This may cause serious injury to a
8. Do not use water the Monito
This may cause damaged the Monitric shock.
9. In case of smoke or stran
Monitor, switch it off ,unpluglet and contact your dealer o
This may cause a fire or could give
10. Do not attempt to service thContact your dealer or servic
This may cause damaged the Monitric shock.
11.During a lightning thunder,
from the wall outlet and doncable.
This may cause damaged the Monitric shock.
WARNING
* Safety instructions have two kinds of information, and each meaning of it is as below.
Take care of danger that may happen under specific condition.
The violation of this instruction may cause serious injuries an
The violation of this instruction may cause light injuries or daproduct.
WARNING
NOTES
Powersupplier
Short-circuitb k
8/4/2019 LG Plasma Monitor
3/36
1. Never touch the power plug with a wet hand.This may cause an electric shock.
2. Disconnect from the mains and remove all con-nections before moving.
3. Do not place the Monitor in a built-in installationsuch as a bookcase or rack.
Ventilation required.
4. When installing the Monitor on a table, be careful
not to place the edge of its stand.
This may cause the Monitor to fall, causing serious injury to achild or adult, and serious damage to the Monitor.
5. Do not place an outside antenna in the vicinity ofoverhead power lines or other electric light orpower circuits.
This may cause an electric shock.
8. Ensure the power cord doeshot objects like a heater.
This may cause a fire or an electric s
9. Do not plug when the power damaged or the connecting palet is loose.
This may cause a fire or an electric s
10. Dispose of used batteries ca
child from eating them.In case that it eats them, take it to se
11. When moving the Monitor assers do not carry holding the spThis may cause the Monitor to fall, cachild or adult, and serious damage to
12. Unplug this product from thecleaning. Do not use liquid ccleaners.
This may cause damaged the Monitotric shock.
13. Contact the service center onthe internal part of the Monitor
Accumulated dust can cause mechan
14. The distance between eyes anbe about 5 ~ 7 times as long asthe screen.
If not, eyes will strain.
15. Unplug the Monitor from the wleft unattended and unused ftime.
Accumulated dust may cause a fire odeterioration or electric leakage.
NOTE
8/4/2019 LG Plasma Monitor
4/36
Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~3
IntroductionControls and Connection Options . . . . . . . . . . . .6
Remote Control Key Functions . . . . . . . . . . . . . .7
InstallationInstallation Instruction . . . . . . . . . . . . . . . . . . . .9~10
External Equipment Connections . . . . . . . . . .11~14
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11
External A/V Source Setup . . . . . . . . . . . . . . . .12
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14
OperationTurning on the Monitor . . . . . . . . . . . . . . . . . . . . .15
Menu Language Selection . . . . . . . . . . . . . . . . . .15
Picture Menu Options
APC (Auto Picture Control) . . . . . . . . . . . . . . . .16
Manual Picture Control . . . . . . . . . . . . . . . . . . .16
Auto Color Temperature Control . . . . . . . . . . . .16
Manual Color Temperature Control . . . . . . . . . .16
Sound Menu Options
DASP (Digital Auto Sound Processing) . . . . . . .17
Manual Sound Control . . . . . . . . . . . . . . . . . . .17AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17
Timer Menu Options
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18
On/Off Timers Setup . . . . . . . . . . . . . . . . . . . . .18
Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Special Menu Options
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Menu Rotation For Vertical Viewing . . . . . . . . . .20
Screen Menu Options
Auto Adjustment . . . . .
Setting Picture Format
Picture Size Zoom . . .
Adjusting Horizontal/Vert
Manual Configure . . . . Screen Adjustments . .
Initializing . . . . . . . . . .
Luminance Noise Reduc
Selecting Wide VGA mo
Split Zoom . . . . . . . . .
PIP (Picture-in-Picture) Fea
Watching PIP . . . . . . .
Swapping the PIP . . . .
Moving the PIP . . . . . .
Selecting an Input Signa
PIP Aspect Ratio . . . . .
Double Window Setup Opt
Watching Double Windo
Sub Picture Size Adjustm
Swapping the Double W
Selecting a Source for th
External Control Device Setup
IR Code . . . . . . . . . . . . . . . . .
Troubleshooting Checklist . . .
Specifications . . . . . . . . . . . . .
ContentsContents
8/4/2019 LG Plasma Monitor
5/36
IntroductionIntroduction
What is a Plasma Display Panel (PDP)?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluoresceinstant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160- Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This meclear and visible to viewers anywhere in the room.
Wide Screen
The screen of the Plasma Display is 42" so wide that your viewing experience is as if you are in a thea
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsinfeature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations whernot fit.
The PDP Manufacturing Process: Why minute colored dots may be present on the PD
The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on thable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not meaThus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our productioto minimize cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, tcooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occuing and cooling the PDP.The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from theoperation of this product. We hope you understand that a certain level of noise from the cooling fans iscient cause for the PDP to be exchanged or returned.
WARNINGTO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PR
RAIN OR MOISTURE.
8/4/2019 LG Plasma Monitor
6/36
Introduction
ControlsControls
Connection OptionsConnection Options
R ( )( )( )( ) L
EXPANDEDINPUT
RS-232C INPUT(CONTROL/SERVICE)EXTERNAL SPEAKER
Y PB PRR AUDIO L
S-VIDAUDIO INPUTAUDIO INPUT REMOTECONTROL
COMPONENT INPUTDVI INPUT RGB INPUT RGB OUTPUT
1
1. EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s).
* For further information, refer to Speaker & Speaker
Stand manual.
6. COMPONENT INPUT/AUDIO I
Connect a component video/au
7. REMOTE CONTROL
C t i d t
Back Connection PanelBack Connection Panel
VOL.MENUON/OFF
INPUT
SELECT
Main Power ButtonINPUT SELECT Button
VOLUME (
PIllumina
Il
Remote Control SensorMENU Button
E, D B
Front Panel ControlsFront Panel Controls
2 4 5 73 6
- This is a simplified representation of front panel.Here shown may be somewhat different from your monitor.
- Connection panels shown may be somewhat different from your monitor.
8/4/2019 LG Plasma Monitor
7/36
Remote Control Key FunctionsRemote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the monitor.- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not fu
as necessary.
1 2 3
4 5 6
7 8
0
9
POWER
MULTIMEDIA INPUT SELECT
APC DASP
ARC SLEEP
PIP DW
SWAP
MENU MUTE
ENTERVOL
POWER
STOP
FF
REC
PLAYREW
P/STILL
WIN.SIZEWIN.POSITION
FAV CHCAPTION
A.PROG PIP CH
PIP CH
ZOOM +
MTS
ZOOM -SPLIT ZOOM
MEMORY/ERASE
VOL
CH
CH
PIP INPUT
POWER
Switches the monitor between
ON and STANDBY.MULTIMEDIA
Selects: Component, RGB, or DVImode.
APC
Adjusts the factory preset picture
according to the room.
ARC
Changes the picture format.
PIP
Switches the sub picture on and off.
SWAP
Exchanges main and sub picture
images.
MENU
Displays on screen menus.
Exits the current menu. ENTER
CHD /ESelects m
VOLF /Increases
Adjusts m
INPUT S
Selects s
Compon
DASP
Selects th
your view
Flat, MuUser.
SLEEP
Sets the s
PIP INPU
Selects th
picture.
MUTE
Switches
ZOOM-/Z
Enlarges size.
DW (DouSelects D
WIN. SIZ
Adjusts th
WIN.POSITION
Moves the sub picture.
NUMBER buttons
Not functional
VCR BUT
Control so
recorders
SPLIT ZOOM
Enlarge the screen with regular
ration.
8/4/2019 LG Plasma Monitor
8/36
Installation
InstallationInstallation
D-sub 15 pin cable
Owners Manual
1.5V
1.5V
Batteries BNC-RCA adapter
Power Cord DVI-D Cable
Ensure that the following accessories are included with your plasma display. If an accessory is missing
where you purchased the product.
Video cables Audio cables
- Optional extras can be changed or modified for quality improvement without any notification new op- Contract your dealer for buying these items.
Option ExtrasOption Extras
Tilt wall mounting bracket Wall mounting bracket Vertical wall mounting bracket(MP-42PZ45M/45V/91M/91V
series models only)
MP-42PZ44/44H/45M/45Vseries models only
MP-42PZ90/90H/9series models
8/4/2019 LG Plasma Monitor
9/36
Installation InstructionsInstallation Instructions
The Monitor can be installed in different ways such as on a wall, or on a desktop etc.
Install this monitor only in a location where adequate ventilation is available.
It is recommended that MP-42PZ44/45V/90/91V series models only be used at an altitude of less than
to get the best quality picture and sound.
It is recommended that MP-42PZ44H/45M/90H/91M series models only be used at an altitude of less
to get the best quality picture and sound.
GROUNDING
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
WWall Mount Installationall Mount Installation
For proper ventilation, allow a clearaside and 2 from the wall. Detailed intions are included from your dealer inMounting Bracket Installation and Se
; ; ; ; ; ;
; ; ; ; ; ;
; ; ; ; ; ;
; ; ; ; ; ;
; ; ; ; ; ;
y y y y y y
y y y y y y
y y y y y y
y y y y y y
y y y y y y
4 inches
4 inches4 inches
4 inches
Desktop Pedestal InstallationDesktop Pedestal Installation
For proper ventilation allow a clearan
8/4/2019 LG Plasma Monitor
10/36
Installation
Installation Instructions continuedInstallation Instructions continued
WWall Mount: Vall Mount: Vertical installation (MP-42PZ45M/45V/91M/91V series models only)ertical installation (MP-42PZ45M/45V/91M/91V series models only)
Detailed installation instructions are optional Vertical Wall Mounting BrackSetup Guide, see your dealer.NOTE: When installing the monitor vpanel controls must be in the left sid
When installing the monhave to change the OSDdisplay mode so that thecorrectly and also to prooverheating (Refer to P.
8/4/2019 LG Plasma Monitor
11/36
External Equipment ConnectionsExternal Equipment ConnectionsNOTE: All cables shown are not included with the plasma display.
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor
- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period ofpicture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the scree
How to connect1. Connect the provided BNC-RCA adapter to the monitors
VIDEO INPUT.2. Connect the audio and video cables from the VCR's output
jacks to the monitor input jacks, as shown in the figure. Whenconnecting the monitor to a VCR, match the jack colors: (Video= yellow, Audio Left = white, and Audio Right = red).
Mono VCR: Connect the video output cable from the VCR tothe VIDEO input on the monitor.S-VIDEO VCR: Connect the S-Video output cable from theVCR to the S-VIDEO input. (Note that S-Video yields higherquality video).
How to use1. Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner s manual.)2. Use the INPUT SELECT button on the remote control to select
Video.
(If connected to S-VIDEO, select the S-Video external inputsource.)
VCR SetupVCR Setup
- After subscribing to a cable TV service from a local provider and installing a converter, you can watcThe monitor cannot display TV programming unless a TV tuner device or cable TV converter box is c
- For further information regarding cable TV service, contact your local cable TV service provider(s).
How to connect1. Connect the provided BNC-RCA adapter to the monitors
VIDEO INPUT.2. Connect the audio and video cables from the cable box's out-
put jacks to the monitor input jacks, as shown in the figure.
CableCable TV SetupTV Setup
S-VIDEOOUT
IN
( R) A UD IO ( L) V ID EO
Y PR AUDIO L
AUDIO INPUT COMPON
VCR
Y PB PR R AUDIOR AUDIO L
8/4/2019 LG Plasma Monitor
12/36
Installation
Component Input portsTo get better picture quality, connect a Dnent input ports as shown below.
- To watch digitally broadcast programs, purchase andconnect a digital set-top box.
DTV SetupDTV Setup
How to connect1. Connect the provided BNC-RCA adapter to the monitors
VIDEO INPUT.2. Connect the audio and video cables from the external
equipment's output jacks to the monitor input jacks, asshown in the figure. When connecting the monitor to exter-nal equipment, match the jack colors (Video = yellow, AudioLeft = white, and Audio Right = red).
How to use1. Use the INPUT SELECT button on the remote control to
select Video.2. Operate the corresponding external equipment. Refer to
external equipment operating guide.
Component ports of theMonitor
Y
Video output portsof DVD player
Y
YYY
How to connect1. Connect the DVD video outputs to the C
INPUT jacks and connect the DVD audioINPUT jacks on the monitor, as shown in
2. If your DVD only has an S-Video output S-VIDEO input on the monitor and conneto the AUDIO INPUT jacks, as shown in
How to use1. Turn on the DVD player, insert a DVD.2. Use the INPUT SELECT button on the r
Component. (If connected to S-VIDEO,
nal input source.)3. Refer to the DVD player's manual for op
ExternalExternal A/V Source SetupA/V Source Setup
DVD SetupDVD Setup
R LA UD IO VI DE O
VIDEOINPUT
Y PB PR (MONOR AUDIO LR AUDIO L
S-VIDEO AUDIO INPUTAUDIO INPUT REMOTECONTROLCOMPONENT INPUT
B R(R) AUDIO (L) (R) AUDIO (L) S-VIDEO
VIDEOINPUT
Y PB PR (MONO)R AUDIO LR AUDIO L
S-VIDEO AUDIO INPUTAUDIO INPUT REMOTECONTROL
COMPONENT INPUT
DVD
or
YR AUDIO L
8/4/2019 LG Plasma Monitor
13/36
How to connect1. To get the best picture quality, adjust the PC
graphics card to 800x600, 60Hz.2. Use the monitors RGB INPUT or DVI (DigitalVisual Interface) INPUT port for video connections,depending on your PC connector.If the graphic card on the PC does not output ana-log and digital RGB simultaneously, connect onlyone of both RGB INPUT or DVI INPUT to displaythe PC image on the monitor.If the graphic card on the PC does output analogand digital RGB simultaneously, set the monitor toeither RGB or DVI; (the other mode is set to Plug
and Play automatically by the monitor.)3. Then, make the corresponding audio connections.If using a sound card, adjust the PC sound asrequired.
How to use1. Turn on the PC and the monitor.
2. Turn on the display by pressing the POWER button on the monitor's remote control.3. Use the INPUT SELECT button on the remote control to select RGB or DVI.4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern
brightness in PC mode. If noise is present, change the PC mode to another resolution, change the reanother rate or adjust the brightness and contrast on the menu until the picture is clear. If the refreshgraphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC
NOTES Depending on the graphics card, DOS mode may not work if you use a DVI-I cable. Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may be
nently imprinted on the screen. Use the Orbiter screen saver when possible.
The synchronization input form for Horizontal and Vertical frequencies is separate.
PC SetupPC Setup
- This Plasma display provides Plug and Play capability, meaning that the PC adjusts automatically to sends configuration information (EDID) to the PC using the Video Electronics Standard Association (Channel (DDC) protocol.
R ( )( )( )( ) L
RS-232C INPUT(CONTROL/SERVICE)EXTERNALSPEAKER
AUDIO INPUTDVI INPUT RGB INPUT RGB OUTPUT
8/4/2019 LG Plasma Monitor
14/36
Installation
Monitor Display Specifications (RGB-PC /DVI-PC Mode)
Resolution
640x350
720x400
640x480
848x480
852x480
HorizontalFrequency(KHz)
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
35.000
37.500
31.500
35.000
37.500
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
54.348
63.995
67.500
68.681
60.000
63.981
5
6
7
7
8
7
6
7
7
6
7
7
7
6
6
VerticalFrequency(Hz)
Resolution
800x600
832x624
1024x768
1152x864
1152x870
1280x1024
HorizontalFrequency(KHz)
VeFrequ
1280x960
8/4/2019 LG Plasma Monitor
15/36
8/4/2019 LG Plasma Monitor
16/36
Operation
- Each adjustment for the Picture menu options doesnt effect other input sources. Readjust Picturemenu options for each of the following sources. RGB (PC) / DVI (PC), RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i) Video / S-Video / Component (480i)
Picture Menu OptionsPicture Menu Options
- You can adjust picture contrast, brightness, color, sharpness, and tint to the levelsyou prefer.
1. Press the MENU button and then use D /E button to select the PICTURE menu.2. Press the G button and then use D / E button to select the desired picture option
(Contrast, Brightness, Color, Sharpness, Tint).
3. Press theG button and then use F / G button to make appropriate adjustments.4. Press the ENTER button to save.
Manual Picture Control (Manual Picture Control (User option)option)
1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
APC (Auto Picture Control)APC (Auto Picture Control)
You can also adjust APC in the PICTURE menu.
Clear, Optimum, and Soft are preset for good picture quality at the factory and cannot be chang
Optimum Soft User Clear
- APC adjusts the Monitor for the best picture appearance.- When adjusting picture options (contrast, brightness, color, sharpness and tint) manually, APC autom
changes to User.
- To initialize values (reset to default settings), select the Normal option.- When adjusting color temperature options (red, green, or blue) manually, ACC
automatically changes toUser
.
1. Press the MENU button and then use D /E button to select the PICTURE menu.2. Press the G button and then use D / E button to select ACC .3. Press the G button and then use D / E button to select either Normal (Default),
Cool (Preset), Warm (Preset) or User (Manual Adjustment).
4 Press the ENTER button to save
Auto ColorAuto Color TTemperature Controlemperature Control
PIC
APC
ACC
Color t
Contra
Brightn
Color
Sharpn
Tint
PIC
PIC
APC
ACC
Color t
Contra
Brightn
Color
Sharpn
Tint
PIC
MENU
8/4/2019 LG Plasma Monitor
17/36
1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.
DASPDASP (Digital(Digital Auto Sound Processing)Auto Sound Processing)
1. Press the MENU button and then use D /E button to select the SOUND menu.2. Press the G button and then use D / E button to select the desired sound option
(Balance, Treble, Bass).
3. Press the G button and then use F / G button to make appropriate adjustments.4. Press the ENTER button to save.
Manual Sound Control (Manual Sound Control (User option)option)
You can also adjust DASP in the SOUND menu. Flat, Music, Movie and Sports are preset for good sound quality at the factory and cannot be
changed.
Flat Music Movie Sports User
- This function lets you enjoy the best sound without any special adjustment because the Monitor hassound options based on the program content.
- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to
- AVL maintains an equal sound level; even if you change channels.
1. Press the MENU button and then use D / E button to select the SOUND menu.2. Press the G button and then use D /E button to select AVL.3. Press the G button and then use D /E button to select On or Off.4. Press the ENTER button to save.
AAVLVL (Auto V(Auto Volume Leveler)olume Leveler)
- You can adjust sound treble, bass, and balance to the levels you prefer.
SO
DASP
AVL
Balance
Treble
Bass
SO
SO
DASP
AVL
Balance
Treble
Bass
SO
MENU
Sound Menu OptionsSound Menu Options
8/4/2019 LG Plasma Monitor
18/36
8/4/2019 LG Plasma Monitor
19/36
Key LockKey Lock
- The monitor can be set up so that it can only be used with the remote control.- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.
- This Monitor is programmed to remember which option it was last set to even if you turn the monitor
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result
image remaining even when you change the image. Avoid allowing a fixed image to remain on the Mscreen for a long period of time.
Special Menu OptionsSpecial Menu Options
SPE
Langua
Key loc
ISM Me
Low po
Set ID
Caption
Caption
OSD Ro
SPE
MENU
1. Press the MENU button and then use D / E button to select the SPECIAL menu.2. Press the G button and then use D /E button to select Key lock.3. Press the G button and then use D /E button to select On or Off.4. Press the ENTER button to save.
With the KEY LOCK ON, the display Key lock appears on the screen if anybutton on the front panel is pressed.
ISM (Image Sticking Minimization) MethodISM (Image Sticking Minimization) Method
SPE
Langua
Key loc
ISM Me
Low po
Set ID
Caption
Caption
OSD Ro
SPE
MENU
1. Press the MENU button and then use D / E button to select the SPECIAL menu.2. Press the G button and then use D /E button to select ISM Method.3. Press the G button and then use D /E button to select either Normal, White
wash, Orbiter, or Inversion.
Normal:If image sticking is never a problem, ISM is not necessary - set to Normal.
White washWhite Wash removes permanent images from the screen. Note: An excessive per-
manent image may be impossible to clear entirely with White Wash. To return to
normal viewing, press the any button.
OrbiterOrbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
8/4/2019 LG Plasma Monitor
20/36
Special Menu Options continuedSpecial Menu Options continued
SP
Langua
Key loc
ISM Me
Low po
Set ID
Caption
Caption
OSD Ro
SPE
MENU
1. Press the MENU button and then use D / E button to select the SPECIAL menu.2. Press theG button and then use D /E button to select OSD (On Screen Display)
Rotate.
3. Press the G button and then use D / E button to select Normal or Rotate. Select Normal, if the monitor was installed horizontally. Select Rotate, if the monitor was installed vertically.
4. Press the ENTER button to save.
Menu Rotation for VMenu Rotation for Vertical Vertical Viewing (MP-42PZ45M/45V/91M/91V series models oiewing (MP-42PZ45M/45V/91M/91V series models o
Operation
Low PowerLow Power
- Low power reduces the plasma display power consumption.SP
Langua
Key loc
ISM Me
Low po
Set ID
Caption
Caption
OSD Ro
SPE
MENU
1. Press the MENU button and then use D / E button to select the SPECIAL menu.2. Press the G button and then use D / E button to select Low power.3. Press the G button and then use D / E button to select On or Off.
When you select On, the screen darkens.
4. Press the ENTER button to save.
8/4/2019 LG Plasma Monitor
21/36
AutoAuto AdjustmentAdjustment
1. Press the MENU button and then use D /E button to select the SCREEN menu.2. Press theG button and then use D /E button to select Auto config..3. Press the G button to run Auto configure.
When Auto config. has finished, OK will be shown on screen. If the position of the image is still not correct, try Auto adjustment again.
4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto con-fig., you can make further adjustments with the Manual config. option.
Screen Menu OptionsScreen Menu Options
SCR
- RGB (PC) mode only; This function doesnt work for RGB-DTV mode.- Automatically adjusts picture position and minimizes image shaking.- After adjustment, if the image is still not correct, your Monitor is functioning properly but needs furthe- The Auto config. and Manual config. are not active in DVI mode.
Auto co
ARC
Zoom in
Position
Manual
Screen
Reset
VGA Mo
SCR
MENU
Setting Picture FormatSetting Picture Format
- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.- Set every aspect ratio for RGB 480p, DVI 480p, Component 480i/480p, Video, and S-Video sources.- Use 4:3, or 16:9 for other input sources.
1. Use the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the
4:3- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appea
left and right sides.
16:9- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire s
Horizon- Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarg
sides, to create a spectacular view.
Zoom- Choose Zoom when you want to view the picture without any alteration. However, the top and bottothe picture will be cropped.
8/4/2019 LG Plasma Monitor
22/36
Adjusting Horizontal/ VAdjusting Horizontal/ Vertical Positionertical Position
1. Press the MENU button and then use D / E button to select the SCREEN menu.2. Press the G button and then use D /E button to select Position.3. Press the G button and then use D /E / F / G button to adjust the position.4. Press the ENTER button to save.
SC
Auto co
ARC
Zoom i
PositioManual
Screen
Reset
VGAMo
SC
MENU
SC
Auto co
ARC
Zoom i
Positio
Manual
Screen
Reset
VGAMo
SC
MENU
Manual Configure (RGB-PC mode only)Manual Configure (RGB-PC mode only)
- If the image still isnt clear after auto adjustment and especially if characters are still jittery, adjust th
Phase manually.- To correct the screen size, adjust Clock.
- This function works in the following modes:RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i).
1. Press the MENU button and then use D /E button to select the SCREEN menu.2. Press the G button and then use D /E button to select Manual config..3. Press the G button and then use D /E button to to select Phase or Clock.4. Use the F / G button to make appropriate adjustments.
The Phase adjustment range is 0 ~ 31. The Clock adjustment range is -50 ~ +50.
5. Press the ENTER button to save.
SC
Auto co
ARC
Zoom i
Positio
Manual
Screen
Reset
YNR
SC
ScreenScreen Adjustments (VAdjustments (Video, S-Video, S-Video and Component 480i mode only)ideo and Component 480i mode only)
- Use this function to correct jittering or picture instability while viewing a video tape.
1. Press the MENU button and then use D /E button to select the SCREEN menu.2. Press the G button and then use D /E button to select Screen adj..3. Press the G button and then use D /E button to select TV or VCR.
Select the VCR option if watching a VCR. Select the TV option for other equipment. (Except VCR)
4. Press the ENTER button to save.
Operation
Screen Menu Options continuedScreen Menu Options continued
8/4/2019 LG Plasma Monitor
23/36
Split ZoomSplit Zoom
- Enlarges the picture in correct proportions.
- Split Zoom can be used for all input sources.- In 2-Split Zoom mode, you can only move the image up or down.- If an image is enlarged, a section can be viewed without using Split Zoom.- Split Zoom is not available if OSD rotate is rotate.
1. Press the SPLIT ZOOM button repeatedly to select either 2, 4, or 9 Split Zoom.
SCR
Auto co
ARC
Zoom in
Position
Manual
Screen
Reset
VGA Mo
SCR
MENU
SCR
Auto co
ARC
Zoom in
Position
Manual
Screen
Reset
YNR
SCR
MENU
Selecting WSelecting Wide VGAide VGA mode (RGB-PC, DVI-PC mode only)mode (RGB-PC, DVI-PC mode only)
- To see a normal picture, match the resolution of RGB mode and selection of VGA mode.
1. Press the MENU button and then use D /E button to select the SCREEN menu.2. Press theG button and then use D /E button to select VGA Mode.3. Press the G button and then use D /E button to select the desired VGA resolution.
4. Press the ENTER button to save.
- Use YNR to reduce the picture noise that may appear on the screen.
Luminance Noise Reduction (VLuminance Noise Reduction (Video, S-video and Component 480i modes only)ideo, S-video and Component 480i modes only)
1. Press the MENU button and then use D /E button to select the SCREEN menu.2. Press the G button and then use D /E button to select YNR.3. Press the G button and then use D /E button to select On or Off.4. Press the ENTER button to save.
8/4/2019 LG Plasma Monitor
24/36
- PIP lets you view 2 different inputs pictures (sources) on your monitor screen at the same time. Onethe other source will show a smaller inset image.
- You can also adjust the PIP features in the PIP/DW menu (Except Swap function).
PIPPIP (Picture-In-Picture) Feature(Picture-In-Picture) Feature
WWatching PIPatching PIP
Press the PIP button repeatedly to turn PIP on or off.
- Press the WIN.SIZE button and then use F / G button to change the subpicture size.
PIPPIP Aspect RatioAspect Ratio
Moving the PIPMoving the PIPPress the WIN.POSITION button.
Press the D / E /F /G button repeatedly until desired position is achieved.The sub picture moves up/down/left/right.You can also move the PIP position with Win.position in the PIP/DW menu.
Swapping the PIPSwapping the PIP
Press the SWAP button to exc
tures.
Selecting an Input Signal Source for the PIPSelecting an Input Signal Source for the PIP
Use the PIP INPUT button to select the input source for the sub picture.
Main Picture Sub Pictur
10 : 30
10: 30
Win.p
ComponentVideo
ComponentVideo
Operation
Main Picture Source Available Sub Picture Sources
VideoS-VideoComponent 480iComponent 480p/720p/1080iRGB and DVI
S-Video, Component 480i/480p/720p/1080i, RGB and DVIVideo, Component 480i/480p/720p/1080i, RGB, and DVIVideo,S-Video, RGB, and DVIVideo and S-VideoVideo, S-Video, and Component 480i,
8/4/2019 LG Plasma Monitor
25/36
- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown onsame time. Each source is given half the screen.
Double WDouble Window Setup Optionsindow Setup Options
Selecting a Source for the Double WSelecting a Source for the Double Windowindow
WWatching Double Watching Double Windowindow
Press the DW button repeatedly to select one of the Double Window options.
Sub Picture SizeSub Picture Size AdjustmentAdjustment
Press the WIN.SIZE button.
Use the F /G button to change the sub picture size. Using the Win.size function in Double Window mode, main and sub picture sizes are
changed simultaneously.
Using the Win.size function in PIP mode, sub picture size is changed.
Win.position is not functional in Double Window mode.
Swapping the Double WSwapping the Double Windowindow
Use the SWAP button to switch the main and sub pictures in Double Window mode.
DW1 DW2
10:30 10:30
ComponentVideo
VideoComponent
Win.s
F
Main Picture Sub Picture
8/4/2019 LG Plasma Monitor
26/36
No. Pin name
1 No connection
2 RXD (Receive data)
3 TXD (Transmit data)
4 DTR (DTE side ready)
5 GND
6 DSR (DCE side ready)
7 RTS (Ready to send)
8 CTS (Clear to send)
9 No Connection
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V controland control the Monitor s functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.- RS-232C connection cables are not supplied with the Monitor.
TType of Connector; D-Sub 9-Pin Maleype of Connector; D-Sub 9-Pin Male
RS-232C ConfigurationsRS-232C Configurations
External Control Device SetupExternal Control Device Setup
RS-232C SetupRS-232C Setup
R ( )( )( )( ) L
EXPANDEDINPUT
VIDEOINPUT
RS-232C INPUT(CONTROL/SERVICE)EXTERNALSPEAKER
Y PB PR (MONO)R AUDIO LR AUDIO L
S-VIDEO AC INPUTAUDIO INPUTAUDIO INPUTAUDIOINPUT REMOTECONTROL
COMPONENT INPUTDVI INPUT RGB INPUT RGB OUTPUT
PC
External Control Device Setup
8/4/2019 LG Plasma Monitor
27/36
Ex
Set IDSet ID
Use this function to specify a monitor ID number.Refer to Real Data Mapping 1. See page 28.
Baud rate : 115200 bps (UART)
Data length : 8 bits
Parity : None
* Use a crossed (reverse) cable.
Stop bit : 1 bit
Communication code : ASCII code
Communication ParametersCommunication Parameters
1. Press the MENU button and then use D /E button to select the SPECIAL menu.2. Press theG button and then use D /E button to select Set ID.3. Press the G button and then use F /G button to adjust Set ID to choose the desired
monitor ID number. The adjustment range of Set ID is 1 ~ 99.
4. Press the ENTER button to save.
SPE
Langua
Key loc
ISM Met
Low po
Set ID
Caption
Caption
OSD Ro
SPE
MENU
Transmission
* [Command 1]: First command to
* [Command 2]: Second comman
* [Set ID]: You can adjust the set IID number in Special m~ 99. When selecting S
PDP set is controlled. Smal (1~99) on menu a(0x0~0x63) on transmi
* [DATA]: To transmit command dTransmit FF data to rea
* [Cr]: Carriage ReturnASCII code 0x0D
* [ ]: ASCII code space (0x20)
[Command1][Command2][ ][Set
TTransmission / Receivinransmission / Receivin
OK Acknowledgement
* The Monitor transmits ACK (ackthis format when receiving normdata is data read mode, it indicthe data is data write mode, it rcomputer.
[Command2][ ][Set ID][ ][OK][Da
01. Power k a 0 ~ 1
02. Input Select k b 0 ~ 4
03. Aspect Ratio k c 0 ~ 3
04. Screen Mute k d 0 ~ 1
05. Volume Mute k e 0 ~ 1
06. Volume Control k f 0 ~ 64
07. Contrast k g 0 ~ 6408. Brightness k h 0 ~ 64
09. Color k i 0 ~ 64
10. Tint k j 0 ~ 64
11. Sharpness k k 0 ~ 64
12. OSD Select k l 0 ~ 1
13. Remote Control Lock Mode k m 0 ~ 1
14. PIP/DW k n 0 ~ 3
15. PIP Aspect Ratio k o 0 ~ 1
16. Split Zoom k p 21 ~99
17. PIP Position k q 0 ~ 3
18. Treble k r 0 ~ 64
19. Bass k s 0 ~ 64
20. Balance k t 0 ~ 64
21. Color Temperature k u 0 ~ 3
22. Red Adjustment k v 0 ~ C8
COMMAND 1 COMMAND 2 DATA(Hexadecimal)
Command Reference ListCommand Reference List
8/4/2019 LG Plasma Monitor
28/36
External Control Device Setup
02. Input Select (Command2:b) (Main Picture Input)
G To select input source for the Monitor.You can also select an input source using the INPUTSELECT button on the Monitor's remote control.
Transmission
Data 0 : RGB1 : Component2 : Video
3 : S-Video4 : DVI
[k][b][ ][Set ID][ ][Data][Cr]
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
01. Power (Command2:a)
G To control Power On/Off of the Monitor.
Transmission
Data 0 : Power Off 1 : Power On
[k][a][ ][Set ID][ ][Data][Cr]
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement
Data 0 : Power Off 1 : Power On
* In a like manner, if other functions transmit FF databased on this format, Acknowledgement data feedback
presents status about each function.
[a][ ][Set ID][ ][OK][Data][x]
05. Volume Mute (Command
G To control volume mute on/offYou can also adjust mute usinremote control.
Transmission
Data 0 : Volume mute on (Volu1 : Volume mute off (Volu
[k][e][ ][Set ID][ ][Data][Cr]
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
03. Aspect Ratio (Command2:c) (Main picture format)
G To adjust the screen format.You can also adjust the screen format using the ARC(Aspect Ratio Control) button on remote control or in theScreen menu
04. Screen Mute (Command
G To select screen mute on/off.
Transmission
Data 0 : Screen mute off (Pictu1 : Screen mute on (Pictu
[k][d][ ][Set ID][ ][Data][Cr]
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
06. Volume Control (Comma
G To adjust volume.You can also adjust volume won remote control.
Transmission
Data Min : 0 ~ Max : 64
Refer to Real data mapp
[k][f][ ][Set ID][ ][Data][Cr]
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command2:g)
G To adjust screen contrast.You can also adjust contrast i
Transmission
Data Min : 0 ~ Max : 64
R f R l d
[k][g][ ][Set ID][ ][Data][Cr]
8/4/2019 LG Plasma Monitor
29/36
Ex
09. Color (Command2:i)
G To adjust the screen color.You can also adjust color in the Picture menu.
Transmission
Data Min : 0 ~ Max : 64
Refer to Real data mapping 1. See page 28.
[k][i][ ][Set ID][ ][Data][Cr]
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
10. Tint (Command2:j)
G To adjust the screen tint.You can also adjust tint in the Picture menu.
Transmission
Data Red : 0 ~ Green : 64
Refer to Real data mapping 1. See page 28.
[k][j][ ][Set ID][ ][Data][Cr]
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command2:h)
G To adjust screen brightness.You can also adjust brightness in the Picture menu.
Transmission
Data Min : 0 ~ Max : 64
Refer to Real data mapping 1. See page 28.
[k][h][ ][Set ID][ ][Data][Cr]
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
13. Remote Control Lock Mo
G To lock the remote control andthe monitor.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: Lock off 1:
If youre not using the remote cotrols on the monitor, use this mon/off, remote control lock is re
[m][ ][Set ID][ ][OK][Data][x]
14. PIP / DW (Command2:n)
G To control the PIP (Picture In piYou can also control the PIP/Dton on the remote control or in
Transmission
Data 0: PIP/DW off1: PIP
2: 3:
[k][n][ ][Set ID][ ][Data][Cr]
Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
G To adjust the screen sharpness.You can also adjust sharpness in the Picture menu.
Transmission
11. Sharpness (Command2:k)
Data Min: 0 ~ Max: 64
Refer to Real data mapping 1. See page 28.
[k][k][ ][Set ID][ ][Data][Cr]
15. PIP Aspect Ratio (Comm
G To select the PIP picture formaYou can also select the PIP pic
on the remote control.Transmission
[k][o][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data 0: 4:3 1:
[o][ ][Set ID][ ][OK][Data][x]
16. Split Zoom (Command2
G To operate split zoom function zoom section number.
Transmission
Data Min: 21 ~ Max:99
[k][p][ ][Set ID][ ][Data][Cr]
8/4/2019 LG Plasma Monitor
30/36
External Control Device Setup
22. Red Adjustment (Comm
G To adjust red in color temperat
Transmission
Data Min: 0 ~ Max: C8
Refer to Real data mapp
[k][v][ ][Set ID][ ][Data][Cr]
Acknowledgement
[v][ ][Set ID][ ][OK][Data][x]
23. Green Adjustment (Com
G To adjust green in color tempe
Transmission
Data Min: 0 ~ Max: C8
Refer to Real data mapp
[k][w][ ][Set ID][ ][Data][Cr]
Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
24. Blue Adjustment (Comm
G To adjust blue in color tempera
Transmission
Data Min: 0 ~ Max: C8
Refer to Real data mapp
[k][$][ ][Set ID][ ][Data][Cr]
Acknowledgement
[$][ ][Set ID][ ][OK][Data][x]
21. Color Temperature (Com
G To adjust color temperature.You can also adjust ACC in th
Transmission
Data 0: Normal 1: Cool 2: W
[k][u][ ][Set ID][ ][Data][Cr]
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
20. Balance (Command2:t)
G To adjust balance.You can also adjust balance in the Sound menu.
Transmission
18. Treble (Command2:r)
G To adjust treble.You can also adjust treble in the Sound menu.
Transmission
Data Min: 0 ~ Max: 64
Refer to Real data mapping 1. See page 28.
[k][r][ ][Set ID][ ][Data][Cr]
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
19. Bass (Command2:s)
G To adjust bass.You can also adjust bass in the Sound menu.
Transmission
Data Min: 0 ~ Max: 64
Refer to Real data mapping 1. See page 28.
[k][s][ ][Set ID][ ][Data][Cr]
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
17. PIP Position (Command2:q)
G To select sub picture position for PIP.You can also adjust the sub picture position usingWIN.POSITION on the remote control or in the PIP/DWmenu.
Transmission
Data 0: Right down on screen1: Left down on screen2: Left up on screen
3: Right up on screen
[k][q][ ][Set ID][ ][Data][Cr]
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
8/4/2019 LG Plasma Monitor
31/36
Ex
27. ISM Method (Command2:p)
G To avoid having a fixed image remain on screen.
Transmission
Data 0: Normal1: White wash
2: Orbiter3: Inversion
[j][p][ ][Set ID][ ][Data][Cr]
Acknowledgement
[ ][ ][S t ID][ ][OK][D t ][ ]
29. Orbiter Time Setting (Co
G To adjust orbiter operation time
Transmission
Data Min: 1 ~ Max: FE
Refer to Real data mappi
[j][r][ ][Set ID][ ][Data][Cr]
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
30. Orbiter Pixel Setting (Co
G To adjust pixel number in orbite
Transmission
Data Min: 0 ~ Max: 9
[j][s][ ][Set ID][ ][Data][Cr]
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
31. Picture Size Setting for Dmode (Command2:t)
G To adjust main window size in
Transmission
Data Min: 0 ~ Max: 64
Refer to Real data mappi
[j][t][ ][Set ID][ ][Data][Cr]
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
32. Auto Configure (Comma
G To adjust picture position and mautomatically. It works only in R
Transmission
25. PIP Input Select (Command2:y)
G To select input source for sub picture in PIP mode.
Transmission
Data 0 : RGB1 : Component2 : Video
3 : S-Video4 : DVI
[k][y][ ][Set ID][ ][Data][Cr]
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
26. Abnormal State (Command2:z)
G To recognize an abnormal state.
Transmission
Data 0: Normal (Power on and signal exist)1: No signal (Power on)2: Turn the monitor off by remote control3: Turn the monitor off by sleep time function4: Turn the monitor off by RS-232C function5: 5V down
6: AC down7: Turn the monitor off by Fan Alarm function8: Turn the monitor off by off time function9: Turn the monitor off by auto off functiona: Turn the monitor off by AV board detect
Data FF:Read
[k][z][ ][Set ID][ ][FF][Cr]
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
8/4/2019 LG Plasma Monitor
32/36
G Connect your wired remote control to the Remote Control port on the Monitor.
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
G Configuration of frame
G Repeat code
G Lead code
1st frame
Lowcustom code
Leadcode
Highcustom code
Data code Data
TC
Tf
T1
C0
Carrier frequency
FCAR = 1/TC = fOSC/12Duty ratio = T1/TC = 1/3
Repeat frame
C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3
Repeat code
9 ms 4.5 ms
0.55 ms
9 ms
2.25 ms
How to ConnectHow to Connect
Remote Control IR CodeRemote Control IR Code
IR CodeIR Code
IR Code
8/4/2019 LG Plasma Monitor
33/36
00H01H02H03H08H
C4HC5H09H10H11H12H13H14H15H16H17H
18H19H0BH98HD5HC6HBFH5AHD8H0EH44H
43H52H4DH60H61H63H64H6BH40H41H69H
6AH7BH79H76H77HAFH99H
R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C Button (Power On/Off)
Discrete IR Code (Only Power On)Discrete IR Code (Only Power Off)R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C Button
R/C ButtonR/C ButtonR/C Button (Video/S-video/Component/RGB/DR/C Button (Component/RGB/DVI)Discrete IR Code (Input RGB Selection)Discrete IR Code (Input DVI Selection)Discrete IR Code (Input Component SelectionDiscrete IR Code (Input Video Selection)Discrete IR Code (Input S-video Selection)R/C ButtonR/C Button
R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C Button (PIP/Double window Exchange)R/C Button (4:3/16:9)R/C ButtonR/C ButtonR/C ButtonR/C Button
R/C ButtonR/C ButtonR/C Button (4:3/16:9/Zoom mode Selection)Discrete (Only 4:3 mode)Discrete (Only 16:9 mode)Discrete (Only Zoom mode)Discrete IR Code
Code (Hexa) Function Note
UP (D)
DOWN (E)
VOL+ (G)VOL- (F)POWER ON/OFF
POWER ONPOWER OFFMUTENumber Key 0Number Key 1Number Key 2Number Key 3Number Key 4Number Key 5Number Key 6Number Key 7
Number Key 8Number Key 9INPUT SELECTMULTIMEDIARGBDVIComponentVideoS-videoSLEEP
ENTER ()
MENUDASPAPCPIPPIP INPUTSWAPPIP ARCDWZOOM +ZOOM -Window Size
Window PositionSplit ZoomARCARC (4:3)ARC (16:9)ARC (Zoom)AUTO CONFIG
8/4/2019 LG Plasma Monitor
34/36
Troubleshooting Checklist
No picture &No sound
Check whether the Monitor is turned on.
Power cord inserted into wall outlet?
Test the wall power outlet, plug other products power cord
where the Monitors power cord was plugged in.
No or Poor coloror Poor picture
Select Color in the PICTURE menu and press the VOLU
(Refer to p.16)
Keep a sufficient distance between the Monitor and the VC
Activate any function to restore the brightness of the pictu
(If still picture is on the screen for more than 5 minutes, th
The remote controldoesnt work
Check to see if there is any object between the Plasma D
remote control causing obstruction.
Are batteries installed with correct polarity (+ to +, - to -)?
(Refer to p.8)
Install new batteries. (Refer to p.8)
Picture OK &No sound
Press the VOLUME (G) button.
Sound muted? Press MUTE button.
Picture appears slowlyafter switching on
This is normal as the image is muted during the startup prtor. Please contact your service centre, if the picture has n
five minutes.
Horizontal/vertical barsor picture shaking
Check for local interference such as an electrical applianc
TTroubleshooting Checklistroubleshooting Checklist
8/4/2019 LG Plasma Monitor
35/36
The specifications shown above may be changed without notice for quality improve
Product SpecificationsProduct Specifications
MODEL
Width (inches / mm)
Height (inches / mm)
Depth (inches / mm)
Weight (pounds / kg)
Power requirement
Resolution
Color
Operating Temperature Range
Operating Humidity Range
MP-42PZ44/44A/44B/44K/44R/44SMP-42PZ44H/44HA/44HB/44HK/44MP-42PZ45M/45MA/45MB/45MK/4MP-42PZ45V/45VA/45VB/45VK/45VMP-42PZ90/90A/90B/90K/90R/90SMP-42PZ90H/90HA/90HB/90HK/90MP-42PZ91M/91MA/91MB/91MK/9MP-42PZ91V/91VA/91VB/91VK/91V
40.7 / 1033
24.5 / 622
3.2 / 81
75 / 34
AC100-240V, 50/60Hz
852 x 480 (Dot)
16,770,000 (256 steps of each R, G
32 ~ 104F (0 ~ 40C)
Less than 80%
8/4/2019 LG Plasma Monitor
36/36