Technical Application LED Downlight
LUZ-DL36-25W(8 inch)
Introduction DL36 downlight retrofit kits are designed with CREE COB LED chip, utilization of high efficient reflector helps to improve lumen output. 4inch, 6inch 8inch and 10inch full sizes with wattage varies from 15W to 50W for different applications. 0-10V dimmable driver works with most of the local dimmers. UL&cUL and energy Star approved, qualified for North America Market.
● Up to 70% energy saving compared tostandard CFL
● Long lifetime of 36,000 hours● 0~10V dimming driver● 40° wide beam angle● CCT: 2700K 3000K 4000K 5000K● No UV/IR light● Environment friendly, without Mercury or any
other hazardous substances
Application notes● IP20 for indoor use● Professional electrician for installation only● Switch off before installation● Do not touch when in use● Keep away from hot steam and corrosive gas
Application AreasIt is designed for general lighting applications in office, supermarket, shop, school, hotel, etc. It is also widely used for public areas, such as stairway, lobby, reception, corridors etc.
Certificate
Technical Specifications
Model Voltage Power PowerFactor
Lumen(±5%)
Beamangle CCT Lifespan CRI Dimmable Dimension
LUZ-DL36-25W AC100-277V 25W ≥0.9 1620 40o 2700K 36000h ≥83 Yes Ø236*220mm
LUZ-DL36-25W AC100-277V 25W ≥0.9 1660 40o 3000K 36000h ≥83 Yes Ø236*220mm
LUZ-DL36-25W AC100-277V 25W ≥0.9 1870 40o 4000K 36000h ≥83 Yes Ø236*220mm
LUZ-DL36-25W AC100-277V 25W ≥0.9 1900 40o 5000K 36000h ≥83 Yes Ø236*220mm
Fixture Compatibility
Rated Wattage
ElectricalClassification
IngressProtection
OperatingTemp
OperatingHumidity
Storage Temp
25W Ⅱ IP20 -20oC~45oC 0~90% -20oC~65oC
Driver data Sheet
Driver data DIM
Input rated Voltage AC100-277V
Frequency 50/60Hz
Input Voltage AC90-305V
Efficiency ≥85%
Total load Wattage 25W±5%
Power Factor ≥0.9
Rated input current ≤0.3A
Full load output Voltage DC35-38V
Rated output current 600mA
Output current range 600mA±5%
Power tolerance ±5%
Current output tolerance ±5%
Dimming range 10%-100%
Dimmer 0V-10V dimmers
Short circuit protection PASS
Over voltage protection PASS
Over temperature protection PASS
Withstand voltage AC3750V
Product Information
220
Ø236
Ø190
Photometric Diagram
Spectral Distribution
380 500 600 700 800Wavelength(nm)
Max=6788 [1.0=20000] 1.13SDCM F2700K
x=0.3439 y=0.3656
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0380 500 600 700 800
Wavelength(nm)
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
380 500 600 700 800Wavelength(nm)
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0380 500 600 700 800
Wavelength(nm)
Spec
trum
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 42.7 DEG
-/+180
-120
-90
-30
120
90
30
0
600
1200
1800
2400
3000
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)30
27
24
21
18
15
12
9
6
3
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 37.7 DEG
-/+180
-120
-90
-30
120
90
30
0
700
1400
2100
2800
3500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)35
31.5
28
24.5
21
17.5
14
10.5
7
3.5
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 37.0 DEG
-/+180
-120
-90
-30
120
90
30
0
700
1400
2100
2800
3500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)35
31.5
28
24.5
21
17.5
14
10.5
7
3.5
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Polar intensity diagram Beam diagramCartesian intensity diagram
UNIT: cdAVERAGE BEAM ANGLE(50%): 37.4 DEG
-/+180
-120
-90
-30
120
90
30
0
700
1400
2100
2800
3500
0
Planar Illuminance Curve
Distance(m)
MH=10mE(LX)35
31.5
28
24.5
21
17.5
14
10.5
7
3.5
0
C0/180C90/270
-25 -20 -15 -10 -5 0 5 10 15 20 25
Max=8694 [1.0=20000] 2.05SDCM F5000K
x=0.3473 y=0.3564
Max=7171 [1.0=20000] 2.12SDCM F4000K
x=0.3841 y=0.3816
Max=5338 [1.0=20000] 3.50SDCM F3000K
x=0.4464 y=0.4049
Height Eavg, Emax Angle: 42.58deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 956.1 lm
2.557ft77.93cm
5.113ft155.86cm
7.67ft233.78cm
10.23ft311.71cm
12.78ft389.64cm
173.2, 261.9fc1864, 2819lx
43.30, 65.48fc466.1, 704.8lx
19.25, 29.10fc207.2, 313.2lx
6.928, 10.48fc74.58, 112.8lx
10.83, 16.37fc116.5, 176.2lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
Height Eavg, Emax Angle: 37.23deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 853.9 lm
2.21ft67.36cm
4.42ft134.73cm
6.63ft202.09cm
8.84ft269.45cm
11.05ft336.82cm
213.0, 309.5fc2292, 3331lx
53.24, 77.37fc573.1, 832.8lx
53.66, 34.38fc254.7, 370.1lx
8.519, 12.38fc91.70, 133.2lx
13.31, 19.34fc143.3, 208.2lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
Height Eavg, Emax Angle: 36.81deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 761.4 lm
2.183ft66.55cm
4.367ft133.10cm
6.55ft199.65cm
8.733ft266.19cm
10.92ft332.74cm
189.9, 280.2fc2044, 3016lx
47.48, 70.04fc511.1, 753.9lx
21.10, 31.13fc227.1, 335.1lx
7.597, 11.21fc81.77, 120.6lx
11.87, 17.51fc127.8, 188.5lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
Height Eavg, Emax Angle: 37.56deg DiameterNote: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance.
Flux out: 867.0 lm
2.231ft68.01cm
4.462ft136.01cm
6.693ft204.02cm
8.925ft272.02cm
11.16ft340.03cm
216.3, 311.4fc2328, 3352lx
54.06, 77.86fc581.9, 838.1lx
24.03, 34.60fc258.6, 372.5lx
8.650, 12.46fc93.11, 134.1lx
13.52, 19.46fc145.5, 209.5lx
16.4ft5m
13.12ft4m
9.843ft3m
6.562ft2m
3.281ft1m
2700K
2700K
3000K
3000K
4000K
4000K
5000K
5000K
90
80
70
60
50
40
30
20
10
0
11:1
3:13
11:2
5:10
11:3
7:10
11:4
9:10
12:0
1:10
12:1
3:10
12:2
5:10
12:3
7:10
12:4
9:10
13:0
1:10
13:1
3:10
13:2
5:10
13:3
7:10
13:4
9:10
14:0
1:10
14:1
3:10
14:2
5:10
14:3
7:10
14:4
9:10
15:0
1:10
15:1
3:10
15:2
5:10
15:3
7:10
15:4
9:10
16:0
1:10
16:1
3:10
16:2
5:10
16:3
7:10
IC
Capacitor
MOS
PCB
LED
Fitting
Environmental temperature
Tem
pera
ture
(o C)
Time
The driver lifespan is based on capacitor working temperature.
Driver lifetime & LED light decay rate
90000
80000
70000
60000
50000
40000
30000
20000
10000
065oC 75oC 85oC 95oC 105oC
Life
time
(hou
rs)
Capacitor Tc (oC)
Driver Lifetime LED Light Decay Rate
% L
umin
ous
Flux
FLUX
△ U'V'
110%
105%
100%
95%
90%
85%
80%
75%
70%
0.0040
0.0035
0.0030
0.0025
0.0020
0.0015
0.0010
0.0005
0.00000 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000
LifeTime (hours)
Polar Diagram Comparison
AVERAGE BEAM ANGLE (50%): 37.7DEG
UNIT: cd
C0/180, 37.6 deg
C30/210, 37.6 deg
C60/240, 37.6 deg
C90/270, 37.7 deg
700
1400
2100
2800
3500
0O
+/-180O
150O-150O
120O-120O
90O-90O
60O-60O
30O-30O
0
Temperature● The testing is operated at 25°C
● The lifetime of capacitor, minimum of 5,000 hours if operated at 105°C, will be doubled whenever the temperature drops 10°C
● The highest withstand temperature of IC, MOS could be 120°C
● The highest withstand temperature of LED junction temperature is 150°C
Installation
NOTE: RETROFIT KIT IS VOLTAGE SPECIFIC. VERIFY PROPER VOLTAGE BEFORE INSTALLATION.
Step 2
Step 5
Step 9
Step 3
Step 6
Step 12
Step 4a
Step 7 Step 8
Step 4b
Step 10 Step 11
Step 1: Remove existing lamp(s)Step 2: Remove and discard existing reflector.Step 3: Open board of side of J-box.Step 4: See 4A and 4B Locate J-box containing supply wires and cut all supply wires leading to the
ballast and output lead of ballast. (May remove wires of ballast)Step 5: Twist out conduit knockout.Step 6: Place LED Driver box thru ceiling cut-out and allow to rest on ceiling.Step 7: Install the supply conduit of Driver Box into the junction box.Step 8: Connect the supply to the LED Driver. Connect GND to wire of green.Step 9: See figure 9, hold the end of the string and pass through the hole on one side of the
fixture. press a while penetrate though the hole inside, and make it tighten. (please clarify where the wire is tighted and the tool is not described)Step 10: Plug the yellow connector of new LED engine to the yellow connector on the end of the
flex conduit provided on the driver box.Step 11: Plug the connector of metal to hole of LED engine.Step 12: Ensure the mounting frame can hold the weight of the whole reflector.Step 13: Restore power after installation of fixture is completed.Step 14: After modification completed, attach the Lamping Replacement Marking Label and
Cautionary Label which provided with the retrofit kit package to the light fixture. The label shall be visible during relamping, and after installation.
Retrofit Kit Contents
A Engine and Light Source
B Reflector
C LED Driver Box
Packaging Information
SIZE(CM) N.W/pc (KGS) G.W.(KGS) Q'TY(PCS)
Carton 68.5*59.5*29 1.7 7 4
CTNS Q'TY(PCS) VOLUME(CBM)
20'' standard container 230 920 28
40'' standard container 460 1840 56
LUZON LIGHTING1945B STREET SUITE A - SAN DIEGO - CA - 92102
619 878 2730 / [email protected]
A
BC