Dillon Super 1050Instruction Manual
May 2007
illonrecision
Products, Inc.
Manufacturers of The World's FinestLoading Equipment
Super 1050, May 2007 5/21/07 12:00 PM Page 1
Table of ContentsSuper 1050 Package Contents 4
How the Super 1050 Works: Stations 1 - 8 5
Super 1050 Assembly 6
Powder Measure Adjustments 8
Primer Magazine 9
Electric Casefeeder 10
Review: How the Super 1050 Works: Stations 1 - 8 10
To Begin Reloading 10
Adjustments 12
Casefeeder 12
Handle 12
Swager 12
Swage Conversion & Adjustment 12
Primer System Change Over Instructions 13
Toolhead Removal 14
Shellplate Removal 14
Casefeed Plunger Conversion 15
Die Adjustments 15
Sizing/Decapping Die - Station 2 15
Back-up Expander Die & Swager - Station 3 15
Powder Die - Station 5 16
Bullet Seating Die - Station 7 17
Crimp Die - Station 8 18
RL 1050 vs. Super 1050 19
Troubleshooting 19
Maintenance 20
Lubrication Points 21 - 22
Caliber Conversion Charts 24 - 25
Parts List 26
Schematics 27 - 31
2
Super 1050, May 2007 5/21/07 12:00 PM Page 2
Warranty AgreementThe Dillon Super 1050 reloader has been designed as a
commercial machine. Our expectation is that its lifeexpectancy will be in excess of two million rounds ofloaded ammunition. All Super 1050 machines are warrant-ed for life from defects in material or workmanship, plus aone-year, 100% warranty against normal wear. All electri-cal/electronic components in Dillon equipment are coveredby a one-year warranty.
Mandatory Safety MeasuresThe reloading of ammunition and the handling of com-
ponents (gun powder and primers) is inherently dangerous,indeed shooting firearms is inherently dangerous. Accidentscan and do occur, sometimes with disastrous results includ-ing, but not limited to, loss of vision, hearing or life. Theseaccidents are nondiscriminatory, they occur with both thenovice and the experienced reloader.
Dillon Precision Products has consciously designed theSuper 1050 with this in mind. We’ve shielded the primermagazine and machined clearance holes for the elimina-tion of powder and primer residue. In short, we have doneeverything we know how, to make the use of our machineas safe as possible.
We cannot however, guarantee your complete safety. Inorder to minimize your risk, use common sense whenreloading and follow these basic rules:
Never operate the machine without ear and eye protec-tion on. Call our customer service department at (800) 223-4570 for information on the wide variety of shooting/safetyglasses and hearing protection that Dillon has to offer. Orvisit our website at: www.dillonprecision.com• PAY ATTENTION: Load only when you can give yourcomplete attention to the loading process. Don’t watch tel-evision or try to carry on a conversation and load at thesame time. Watch the automatic systems operate and makesure they are functioning properly. If you are interrupted ormust leave and come back to your loading, always inspectthe cases at every station to insure that the proper opera-tions have been accomplished.• SMOKING: Do not smoke while reloading or allow any-one else to smoke in your reloading area. Do not allowopen flames in reloading area.• SAFETY DEVICES: Do not remove any safety devicesfrom your machine or modify your machine in any way.• MODIFICATIONS: Any modifications performed to yourmachine, or the addition of any unapproved equipmentfrom other manufacturers will void the warranty.• LEAD WARNING: Be sure to have proper ventilationwhile handling lead components or when shooting leadbullets. Lead is known to cause birth defects, other repro-ductive harm and cancer. Wash your hands thoroughly afterhandling anything made of lead.• LOADS AND LENGTHS: Avoid maximum loads and pres-sures at all times. Use only recommended loads from man-uals and information supplied by reliable component man-ufacturers and suppliers. Since Dillon Precision has no con-
trol over the components which may be used on theirequipment, no responsibility is implied or assumed forresults obtained through the use of any such components.
Seat bullets as close to maximum cartridge length aspossible. Under some conditions, seating bullets excessive-ly deep can raise pressures to unsafe levels. Refer to a reli-able loading manual for overall length (OAL).• QUALITY CHECKS: Every 50-100 rounds, perform peri-odic quality control checks on the ammunition being pro-duced. Check the amount of powder being dropped andprimer supply.• RELOADING AREA: Keep your components safelystored. Clear your work area of loose powder, primers andother flammables before loading.• COMPONENTS: Never have more than one type of pow-der in your reloading area at a time. The risk of a mix-up istoo great. Keep powder containers closed.
Be sure to inspect brass prior to reloading for flaws,cracks, splits or defects. Throw these cases away.
Keep components and ammunition out of reach of chil-dren.• BLACK POWDER: Do not use black powder or blackpowder substitutes in any Dillon powder measure. Loadingblack powder cartridges requires specialized loading equip-ment and techniques. Failure to do so can result in severeinjury or death.• PRIMERS: Never force primers. If they get stuck in theoperation of the machine, disassemble it and gently removethe obstruction.
Never attempt to clear primers that are stuck in eitherthe primer pickup tube or the primer magazine tube. Never,under any circumstances, insert any type of rod to attemptto force stuck primers out of these tubes. Trying to forceprimers out of the tube will cause the primers to explodecausing serious injury or even death.
If primers get stuck in a primer magazine or pickup tubeflood the tube with a penetrating oil (WD-40), throw thetube in the garbage and call us for a free replacement.
Never attempt to deprime live primers – eventually onewill go off. When it does it will detonate the others in thespent primer cup. Depriming live primers is the single mostdangerous thing you can do in reloading and can causegrave injury or death.• LOADED AMMUNITION: Properly label all of yourloaded ammunition (Date, Type of Bullet, Primer, Powder,Powder Charge, etc.).• BE PATIENT: Our loading equipment is conservativelyrated and you should have no trouble achieving the pub-lished rates with a smooth, steady hand. If something does-n’t seem right, stop, look and listen. If the problem or thesolution isn’t obvious, call us. The reloading bench is noplace to get into a hurry.• REMEMBER: If your machine does not perform to yourexpectations, or if you are having technical difficulties, giveus a call. Technical Support (800) 223-4570 or visit ourtroubleshooting section at: www.dillonprecision.com
3
Super 1050, May 2007 5/21/07 12:00 PM Page 3
4
Super 1050 Package Contents
items not to scale
items not to scale
• Super 1050 machine with caliber spe-cific shellplate and loading diesinstalled and adjusted.
• Casefeeder Assembly: casefeed bowl,caliber specific casefeed plate, case-feed mounting post, casefeed tube,and post studs
• Collection bin support bracket• Bullet bin bracket• Collection bin• Bullet bin• Spent primer cup• Powder measure assembly
• Powder bar return rod assembly• Primer early warning system• Operating handle• Die box
See the schematics pages in the backof this manual for more detail.
Super 1050, May 2007 5/21/07 12:00 PM Page 4
How the Super 1050 WorksStations 1 - 8 (counterclockwise)
toolhead and dies cut away for clarity
Station 1: Empty cases are automati-cally inserted into the shellplate via theelectric casefeeder.
Station 2: Here the spent cartridgecases are resized and deprimed.
Station 3: This station is totallyunique. The case is supported from theinside and slightly expanded (not belled)while simultaneously a swager is driveninto the primer pocket to remove anycrimp.
Station 4: A new primer is installedat this station. The spring drivenprimer slide is extremely smooth. Thesteel shrouded primer magazine iscapped with an electronic EarlyWarning Device to let you know when
you’re down to approximately threeprimers.
Station 5: Here the case is belled andpowder is dropped by the case-activatedpowder measure. It is extremely accurateand will not drop powder unless a caseis present. Dillon Precision offers anoptional accessory to be utilized with theautomatic powder measure at this station– Dillon’s Low Powder Sensor providesan audible and visual reminder when it’stime to refill the powder reservoir.
Station 6: This station is open to allowfor case inspection.
Station 7: The bullet is seated to itsproper depth at this station.
Station 8: In this station, the bullet iscrimped into place. The cartridge is thenautomatically ejected into a collectionbin.
Your dies have been adjusted at thefactory. Before you change anything, tryit the way it is, once you thoroughlyunderstand the machine’s operation,
5
Station 5 - Here the case mouth is belledand powder dispensed.
Station 1 - The casefeed plunger inserts thecase into the shellplate.
Station 2 - Here, spent cartridge cases areresized and deprimed.
Station 7 - In this station, the bullet is seat-ed to its proper depth.
Station 8 - Here the case is crimped andthen ejected out of the shellplate with thenext pull of the handle.
Station 3 - Here the case mouth is expand-ed while a rod supports the case base forswaging.
Super 1050, May 2007 5/21/07 12:00 PM Page 5
make whatever adjustments to the diesyou feel necessary.
Reminder: There may be some varia-tion due to components.
Super 1050 AssemblyYour new Super 1050 has been
assembled at the factory. All of theadjustments necessary to reload havealready been made, in fact we’ve evenadjusted the dies to reload the caliberyou have chosen. However, beforeyou can reload you must do someminor assembly.
Due to variations in components,check all stations for proper settingsbefore loading ammunition. It isabsolutely necessary that you read thefollowing instructions.
If you get stuck on something that youdon’t understand, call (800) 223-4570for technical assistance.
Step 1: Mounting the Super 1050 Select a clear area on your reloading
bench. Be certain your bench is freefrom vibration and is strong enough tosupport your Super 1050’s mass andoperating force. If possible, attach yourbench to the wall using screws.
Remove the Super 1050 main framefrom the packaging and place it onyour selected area. The crank extension(#11061) should be to your right. Bringthe machine to the forward edge ofyour bench – be sure to allow clear-ance for operation of the handle. Markthe four mounting holes using the
machine as a template. Remove themachine and drill four 1/4” holesthrough the bench. Replace themachine and bolt securely. Fig. 1
Install the handle (#17071) as indicat-ed in the parts schematic. Secure inplace with the handle set screw(#13432). Fig. 2 You will note that thereare three different positions for mountingthe operating handle. Choose the onethat feels best for you. The longer thehandle, the less force required but thestroke is longer.
The toolhead (#20420) is held downon the main frame for shipping by theuse of plastic ties. Remove the ties whileholding the handle Fig 3.
Slowly move the handle up. This willmove the toolhead approximately threeinches to its “up” position. Note: If the
handle is not moving freely, carefullyinspect for shipping damage.
Install the six brass locator buttonsaround the shellplate (#12600*). Fig. 4
Step 2: Installing the Casefeed AssemblyUsing the screw provided (#13377)
install the bin bracket (#13238). Fig. 5
Install the bullet bin bracket(#12144) to the casefeed post (#20641)using the screw (#13685) as shown inthe schematic on page 30.
Screw the casefeed post studs(#13271) to the main frame (placethe washer provided on the bottompost only), tighten securely with anAllen wrench through the cross holeprovided.
The casefeed mounting post assem-bly (#20641) is attached to the case-feed post studs (#13271) by the use oftwo post bolts (#13205). Attach the
Fig. 1 - Be sure the machine is to the for-ward edge of the table or bench whenmarking the four holes to be drilled.
Fig. 2 - Note that there are three differentpositions for mounting the operating handle.
Fig. 3 - Be sure to hold the operating handlein place while cutting the plastic ties.
Fig. 4 - Locator button being inserted intoits proper position.
Fig. 5 - See the schematic on page 30 formore details.
6
Super 1050, May 2007 5/21/07 12:00 PM Page 6
power cable and clamp and supportbin bracket (#10991) as shown in theschematic on page 30. Fig. 6
The casefeed bowl assembly needs
to be placed on the casefeed post withthe Dillon logo and the on/off switchfacing you.
The casefeed tube (#20533*) shouldnow be inserted into the casefeedadapter (#13654*) Fig. 7 Note thatthe tube is marked “up” on one end.Press this end into the tube clip(#13859) attached to the casefeedermotor housing Fig. 8. This assembly isnow complete.
Step 3: Installing the Powder MeasureRemove the blue cap from the powder
die (#20320) and loosely clamp thepowder measure in position. Fig. 9Install the powder measure return rod(#13960) through the 3/8” eyebolt(#13089) mounted on the left rear of themain frame. Fig. 10 Now attach the rodto the powder measure bellcrank usingthe clip. Fig. 10 Install the spring(#14033) and wing nut (#13799) on therod and screw the wing nut up until youfeel light tension on the spring. Tightenthe powder measure clamp screws(#14037).
Step 4: Installing the Spent Primer Cupand Bullet Bin
Install the spent primer cup (#16699)on the right side as shown on theschematic on page 27. Fig. 11
Hook the bullet bin (#13756) and thecollection bin (#13484) on to theirrespective brackets. Fig. 12
Fig. 6 - Shown is the proper position of thepower cable (13539), clamp (13495), andbin support bracket (10991).
Fig. 7 - The proper location and positioningof the casefeed tube and adapter is asshown above.
Fig. 8 - The end of the casefeed tube marked“up” snaps into the clip at the base of thecasefeeder motor housing.
Fig. 9 - See arrow. A slight gap allows thepowder die to be adjusted without removingthe powder measure.
Fig. 10 - Note how the spring above thewing nut is slightly compressed.
Clip
Spring
Fig. 11 - See the schematic on page 27 formore details.
Fig. 12 - Shown is the proper location ofthe cartridge collection bin. Note: the bul-let bin is replaced by the optional bullettray in this photo.
7
Super 1050, May 2007 5/21/07 12:00 PM Page 7
Step 5: Cycling the MachineAt this point your assembly should be
complete. Gently pull the operating han-dle towards you, make a full stroke tothe bottom and up again. The shellplateshould be indexing and the primer slide(#20318*) should function. The casefeedplunger (#13073*) should travel forwardto the shellplate. Make sure that yourepeat this several times to gain anunderstanding of the various functions ofthe machine before you start reloading.Fig. 13
Now plug in the casefeed motor andactivate the switch. The casefeed plateshould turn smoothly within the case-feed bowl.
Assuming that all is well, proceedwith components.
Loading ComponentsYour Super 1050 is equipped with a
cartridge activated powder measure thatwill dispense powder only when a car-tridge is in Station 5.
It is important to understand that theadjustable powder bar should reach theend of its travel at the same time thatthe handle reaches the bottom of its
stroke against the frame stop. Fig. 14To achieve this adjustment, the diebody must be screwed up or down asneeded.
The powder die has already beenadjusted at the factory. An empty casemust be placed in the shellplate atStation 5 in order to check this adjust-ment. Note that the case used to adjustthe powder measure die must already besized.
NOTE: If you are adjusting for astraight wall case, start your powder dieadjustment with the die obviously toohigh and work down. This will avoidover belling the case.
If you are adjusting a case with ashoulder, such as a .223, do not turn thedie down too far or the shoulder willbuckle.
Use a reloading manual to determinehow much powder you need for a par-ticular load and an accurate powderscale to determine the weight. Caution:
While you do not have to use a DillonPrecision powder scale, you should usea scale of equal quality. Do not usescales with plastic frames or “razorblade” pivots. Quality scales have jew-eled pivot points. Razor blade pivotscan dig into the frame of the scale andgive dangerously inaccurate readings.
Powder Measure AdjustmentsIn Station 5 we adjust the powder
measure. It works like this: screw thepowder die into the toolhead and insertthe pistol powder funnel expander or arifle powder funnel with the grooved endtoward the top of the powder die. Fig.15 The funnel should move freely in thedie, leaving a loose fit between the topof the die and the powder measure col-lar. This will enable you to adjust the dieto give you a bell on the mouth of yourpistol cases making it easier to start thebullet.
On rifle cases, the die should beadjusted so that the powder funnel willcontact the mouth of the case and thenfully actuate the powder bar. Theseadjustments are accomplished with asized case in the shellplate and alter-nately raising and lowing the operatinghandle while adjusting the powder die.
When properly adjusted, the powderbar will be moved to the end of its travelby the cartridge case Fig. 14.
When you have determined that youradjustments are correct, tighten the lockring (#14067). Fig. 16
Powder Bar Return Rod AssemblyThe purpose of the powder bar return
rod is to return the powder bar to itsclosed position.
Fig. 13 - Cycle the handle several times toobserve the various functions.
Fig. 14 - This photo shows the powder bar atthe end of its travel.
Fig. 15 - Note the difference between therifle expander (center) and the pistolexpander (right).
Fig. 16 - Be sure to tighten the lock ringwhen adjustments are completed.
8
Super 1050, May 2007 5/21/07 12:00 PM Page 8
Remove the blue cap from the powderdie (#20320) and loosely clamp thepowder measure in position.
To install the powder bar return rod(#13960) remove the blue wing nut(#13799) and rod spring (#14033) fromthe rod, then insert the bottom endthrough the 3/8” eyebolt (#13089) that ismounted on the left rear of the mainframe.
Next, using your thumb and index fin-ger of your left hand, move the locklinkdown and align the hole with the slot onthe bellcrank. Then, insert the rodthrough the two holes and insert thereturn rod clip (#13929). Fig. 17
Install the spring (#14033) and wingnut (#13799) on the rod and screw thewing nut up until you feel light tensionon the spring. Fig. 18 Tighten the pow-der measure clamp screws (#14037).
You will notice an adjusting bolt on
the front of the powder bar. Counter-clockwise reduces the powder charge,clockwise increases the charge. Fig. 19
Your machine comes with two powderbars. Fig. 20 One large (#20063) andone small (#20062).
Index a sized and primed case underthe measure and operate the machine’shandle. Turning the powder bar adjust-ment bolt clockwise increases the pow-der charge – counterclockwise turnsdecreases the powder charge. By trialand error, determine the correct weightof your powder charge by using a pow-der scale. Fig. 19
When the correct powder chargehad been set, cycle several casesthrough the machine and check theload with a scale.
Primer MagazineSelect the proper size primer pick-up
tube and fill it by placing the plastic tipover loose primers and pressing down.
You will notice that the primer maga-zines and primer pick-up tubes have dif-ferent colored tips. They have been colorcoded to help you identify size moreeasily.
The color code is as follows:Blue Small Primer Magazine
OrificeRed Large Primer Magazine
OrificeYellow Small Primer Pick-up TubeGreen Large Primer Pick-up Tube
The shiny side of the primers shouldbe facing up. This is most easily accom-plished by use of a primer flip tray. Fig.21 This quality cast metal flip tray isavailable from Dillon Precision and is abetter choice than the smaller plastictrays which are difficult to use and havea tendency to warp.
Once you’ve filled the pick-up tube,make sure the little retaining clip is inplace at the top of the tube. Fig. 22Pivot the switch lever (#13864) awayfrom the Early Warning System housing
Fig. 17 - Install the return rod clip to securethe powder bar return rod. See the schemat-ic on page 31 for more details.
Fig. 18 - See the schematic on page 31 formore details.
Fig. 19 - Clockwise turns of the powder baradjustment bolt increase the powder chargewhile counterclockwise turns decrease thepowder charge.
Fig. 20 - Small powder bar (left), large pow-der bar (right).
Spacer
Fig. 21 - All of the primers must be shinyside up.
9
Fig. 22 - When installing primers into theprimer magazine, be sure the pick-up tubecenters itself before pulling the clip.
Super 1050, May 2007 5/21/07 12:00 PM Page 9
and invert the pick-up tube over theprimer shield cap (#13957). You willnotice the cap has a bevel to help youfunnel the primers in. Hold the tube inplace as shown in Fig. 22, pull theretaining pin and allow the primers todrop into the magazine. Pivot theswitch the lever back over the EarlyWarning System housing. Gently slidethe follower rod down through theswitch lever and into the primer maga-zine tube. When you are nearly out ofprimers, approximately three remaining,the follower will activate the buzzer.
The Electric CasefeederUse only clean cartridge cases that
have been inspected for any potentialproblems; split cases, rocks or smallercaliber cartridges that may be hidden inlarger caliber cartridges. Fig 23
Warning: Be sure that no loaded roundsare mixed with your empty cases. It ispossible to feed a blunt nosed cartridgelike a .38 Sp. WC into the shellplateupside down and explode it when it ishit by the decap pin.
Now fill the casefeed bowl with
approximately 500 pistol cases or about350 rifle cases. Fig 24
Your Super 1050 is now charged withcomponents and ready to go, but beforeyou start reloading, read the followingexplanation of the sequence of the eightreloading stations and the processes thatare done at each station.
Review: How the Super1050 Works
Stations 1 - 8 (counterclockwise)Station 1: Empty cases are automati-
cally inserted into the shellplate via theelectric casefeeder.
Station 2: Here the spent cartridgecases are resized and deprimed.
Station 3: This station is totallyunique. The case is supported from theinside and slightly expanded (not belled)while simultaneously a swager is driveninto the primer pocket to remove anycrimp.
Station 4: A new primer is installedat this station. The spring drivenprimer slide is extremely smooth. Thesteel shrouded primer magazine iscapped with an electronic EarlyWarning Device to let you know whenyou’re down to approximately threeprimers.
Station 5: Here the case is belled andpowder is dropped by the case-activatedpowder measure. It is extremely accurate
and will not drop powder unless a caseis present. Dillon Precision offers anoptional accessory to be utilized withthe automatic powder measure at thisstation – Dillon’s Low Powder Sensorprovides an audible and visual reminderwhen it’s time to refill the powder reser-voir.
Station 6: This station is open to allowfor case inspection.
Station 7: The bullet is seated to itsproper depth at this station.
Station 8: In this station, the bullet iscrimped into place. The cartridge is thenautomatically ejected into a collectionbin.
As stated earlier, your dies have beenadjusted at the factory. Before youchange anything, try it the way it is,once you thoroughly understand themachine’s operation, make whateveradjustments to the dies you feel neces-sary.
Reminder: There may be some varia-tion due to components.
To Begin ReloadingTurn on the switch on the front of the
casefeed motor housing. The casefeederplate should begin to turn. Cases willbegin to dispense, base down, into theclear plastic casefeed tube. The motorwill continue to run until the tube is full,at which point a micro-switch will tem-porarily stop the case flow.
From this point the casefeeder willautomatically fill the tube as you reload.If the casefeeder does not function prop-erly or the cases do not fall base down,refer to the Troubleshooting section ofthis manual.
Fig. 24 - The casefeed bowl will holdapproximately 500 pistol cases or 350 riflecases. Do not overload the casefeed bowl.
Fig. 23 - When loading, use only cleanedand inspected cartridge cases.
Station 1 - The casefeed plunger inserts thecase into the shellplate.
Fig. 25 - Dillon’s Low Powder Sensor givesan audible and visual warning when thepowder reservoir gets low.
10
Super 1050, May 2007 5/21/07 12:00 PM Page 10
Pull the operating handle smoothly tothe bottom stop, then raise the handle, acase has been fed to Station 1. Cycle thehandle again, strive to be smooth in youroperation.
The first case should be indexed toStation 2. Cycle the handle again.
It is not necessary to apply any forceon the upstroke of the handle. All youare doing on the upstroke is indexing theshellplate. Remember that priming isdone on the down stroke. A slow meas-ured upstroke gives you lots of time topick up the next bullet and ready it forseating. If you count one second down,and one second up, you’ll have a goodpace.
The first case should now be inStation 3 with a case in Stations 1 & 2
as well. Cycle the handle again. Thecase is swaged and expanded at Station3. Observe the swage operating part(#20314*), if the swage is proper, pro-ceed – if not see items 3 and 4 in theTroubleshooting section of this manual.Cycle the handle again and the case getsprimed at Station 4.
If the primer is not seated properly(too high or too deep) you will need toadjust the primer push rod (#12819).Clockwise turns of the primer push rodwill cause the primer to be seated deep-er while counterclockwise turns will seatthe primer higher.
The first case in the sequence shouldnow be primed and at Station 5.Remove the locator button (#20637*),extract the round and check the primer.If everything looks okay, replace thecase and button and proceed.However, if the primer is not seatedproperly (too high or too deep) you willneed to adjust the primer push rod(#12819). Clockwise turns of the primerpush rod will cause the primer to beseated deeper while counterclockwiseturns will seat the primer higher.
Cycle the handle again, the automaticpowder measure will drop the chargeyou’ve selected. Pistol casemouths willbe belled at this time. Look through theinspection hole in Station 6 – youshould be able to see your powdercharge in the case.
Cycle the handle again. Now, withyour left hand, place a bullet on thepowder-charged case at Station 7 andcycle the handle. Your bullet will beseated to its proper depth, if not, a sim-ple height adjustment to the seating stemmay be necessary. Refer to a loadingmanual for proper loaded length (OAL).
Cycle the handle again and check forcrimp at Station 8. Refer toTroubleshooting item 8 for adjustments ifnecessary. Add a bullet, cycle again.Your first loaded round should now beejected into the collection bin.
If all has gone well to this pointyou’ve got it made. Just keep adding bul-lets, watch your fingers so they don’t getcaught and don’t hurry. Just try to besmooth in your operation. The speed willcome naturally and you’ll be doing athousand rounds per hour before youeven realize it.
The following are some adjustmentsuggestions as well as Troubleshootinghints.
11
Station 5 - Here the case mouth is belledand powder dispensed.
Station 2 - Here, spent cartridge cases areresized and deprimed.
Station 7 - In this station, the bullet is seat-ed to its proper depth.
Station 8 - Here the case is crimped andthen ejected out of the shellplate with thenext pull of the handle.
Station 3 - Here the case mouth is expand-ed while a rod supports the case base forswaging.
Super 1050, May 2007 5/21/07 12:00 PM Page 11
AdjustmentsCasefeeder
It may be necessary to readjust themicro-switch for different calibers.Cases may become lodged between themicro-switch and the tube wall. Theother extreme is the case failing to putenough pressure on the micro-switch toshut off the system causing it to contin-ue running and over flowing the tube.
Remove the two clutch screws(#13732), lock washer (#13813) andupper clutch (#13632) and the case-feed plate. Place the spacer on theshoulder of the lower clutch andreassemble – see the schematic onpage 31 for more details. The casefeedplate should now be approximately1/8” above the floor of the casefeedbowl. Note: Make sure the casefeedplate is centered in the bowl. Fig. 26
HandleThe operating handle is adjustable to
three different length settings Fig. 27.Choose the one most comfortable foryour operation. Loosen the set screw(#13432) then retighten when the handleis in the most comfortable position.
SwagerSwaging on the Super 1050 is a sim-
ple process and is necessary on all car-tridge cases as a means of uniformingthe entrance of the primer pocket. Fig.28 The swage rod (#20314 large or#20313 - small) is fully adjustable.
Swage Conversion andAdjustment Conversion – Fig. 29
Begin by removing the swage cover(#13064). Next remove the hitch pin(#13840) and slide out the clevis pin
(#13522). Remove the operating handle.Rotate the swage connecting rod a halfturn and remove it. This will allow youaccess to the swager. Pull the swagerdown and out of the machine. Fig. 29
Insert the new swager and reassem-ble.
Swage AdjustmentsUse ONLY an unswaged military case
for these adjustments.
With the handle in the down posi-tion, screw the swage back-upexpander down until it makes contactwith the case bottom and holds it inplace. Fig. 30
With the handle still in the down posi-tion, turn the swage rod up until itmakes contact with the case bottom.
Raise the handle halfway and rotatethe swage rod a quarter turn. Now, cyclethe handle. Inspect the case and whenyou achieve a completed swage of theprimer pocket, tighten the swage locknut (#14067).
A properly swaged pocket will showa rounded edge around the rim. Somemilitary cases (.223 & .308) start outwith three small dents around the base
Fig. 26 - Make sure the casefeed plate iscentered in the bowl with approximately1/8” all the way around.
Fig. 29 - See the schematics on page 28 formore details.
Fig. 28 - Note the difference between theswaged primer pocket (left) and theunswaged primer pocket (right).
Fig. 31 - Note the difference between theswaged primer pocket (left) and theunswaged primer pocket (right).
Fig. 27 - Note that there are three differentpositions for mounting the operating handle.
1/8”
Fig. 30 - A cutaway view of a .45 ACP withthe swage rod and the back-up rod properlyadjusted in the swaging position.
12
Super 1050, May 2007 5/21/07 12:00 PM Page 12
of the pocket, once properly swaged,the dents will no longer be visible. Fig.31
Primer System Change OverInstructions
The Super 1050 has been shipped toyou with either the large or small primersystem installed. To change the systemfrom large to small or vise versa, followthese instructions:
Be sure all primers have beenremoved from the primer system. Thenremove the Early Warning System andthe knurled cap. Then remove the primermagazine (#22031 - large or #22030 -small) and replace it with the new sizemagazine. Be sure the key on the tip(#14003 - large or #14024 - small) is inthe slot and the magazine is all the waydown in place. Fig. 32
Pull the operating handle to its downposition.
Loosen the lever arm bracket screw(#14037) and slide the bracket assem-bly up four inches and lock it inplace. Fig. 33
Raise the operating handle, removethe two primer feed body screws(#13363) and lift off the primer feedbody assembly (#20773).
Remove the toolhead ratchet (#11688)by removing the bolt (#12486). Fig. 34
Remove the powder bar return rod(#13960) from the powder measure bellcranklock link assembly (#11234) by releasing thereturn rod clip (#13929). Fig. 35
Remove the casefeed tube (#20533*)and place it on your bench. Removethe toolhead. Fig. 36 For more infor-mation see the following section:TOOLHEAD REMOVAL.
Now remove the shellplate lock nut(#13425) by loosening the four locatortab screws (#13895) about four fullturns. Fig. 37
Loosen the ejector tab screw
(#13896) and swing the ejector tab(#13189) out of the way. Fig. 38 Next,slide the casefeed plunger (#13073*)back and remove the shellplate.
Rotate the primer slide stop (#13108)90˚. This will allow you to remove, andreplace, the primer slide (#20318 - largeor #20317 - small). Fig. 39
Next, remove the bushing (#13031 -large or #13222 - small); spring(#13858) and punch (#12849 - large or#13307 - small) and replace them withthe parts for your new primer size.Note that there is a specially designed
13
Fig. 32 - Note the shape of the key at thebase of the primer magazine tip.
Fig. 33 - Slide the bracket assembly up andout of the way – retighten the lever armbracket screw to hold it in place.
Fig. 35 - After removing the clip and discon-necting the rod, replace the clip in the rodfor safe-keeping.
Fig. 36 - To remove the toolhead unscrewthe toolhead bolt and remove.
Fig. 34: Remove the toolhead ratchet by firstremoving the bolt (#12486). See theToolhead schematic on page 27
Fig. 37 - The four lock ring screws need onlybe loosened about four turns to remove theshellplate lock nut.
Fig. 38 - Loosen the screw and swing theejector tab out of the way.
Super 1050, May 2007 5/21/07 12:00 PM Page 13
screwdriver supplied for the bushing(included in the accessory bag). Fig. 40
You should clean your machine atthis time. Fig. 41
Prior to installation, lube the base ofthe primer punch. Now adjust your newpunch (#12849 - large or #13307 -small) so that it is flush with the bushing(#13130 - large or #13222 - small) byturning set screw (#13226) up or down.If the primer punch is too low, dirt will
collect on top of it leaving imprints onyour primers. If it is too high it will bindthe slide. Note: You can use the slide fora guide. Slide it back and forth over thebushing to check your adjustments. Seethe schematic on page 29 or the trou-bleshooting section for additional infor-mation.
To return the lever arm bracket assem-bly to proper position, manually movethe primer slide underneath theshellplate. Pull the operating handledown. Loosen the bracket screw, slidethe assembly down until it touches thebottom of the primer slide slot in theframe. Back the bracket up about .010”,retighten bracket screw.
Toolhead RemovalDisconnect the powder bar return rod
(#13960) from the bellcrank (#11234) byreleasing the return rod clip (#13929).Fig. 42
Remove the Primer Early Warningdevice.
Raise the primer slide lever assembly(#20488) and lock in place - see Fig. 34.
Obtain a 15/16” socket or wrench(not supplied) to remove the toolheadbolt (#13342) and washer (#13449).Fig. 43
Now remove the toolhead (#20420).Due to being spring loaded, there willbe some resistance. Wiggle the toolheadup and off while holding the handle.
After removing the toolhead, carefullylower the handle.
When reinstalling the toolhead bolt(#13342) turn it in only finger tight thencycle the handle up and down to make
sure everything is properly located. Withthe handle in the down position, tightenthe toolhead bolt with the above men-tioned wrench.
Shellplate RemovalLoosen the ejector tab screw
(#13896) and swing the ejector tab(#13189) out of the way. Fig. 38
Loosen the four locator tab screws(#13895) about four full turns. Fig. 37
Use a toothbrush to remove any pow-der that may be in the threads beforeremoving the lock ring.
Next remove the lock ring (#20311).Now push the casefeed plunger back(#13073*) and lift the shellplate off. Besure to lightly grease the bore of theshellplate when reinstalling it. Fig. 44
Rule of thumb: turn the lock ringdown until tight then back off one-eighthof a turn. Then tighten the four locatortab screws (#13895).
14
Fig. 39 - Rotate the primer slide stop 90˚ tomove the primer slide freely in or out.
slide stop
Fig. 40 - A special screwdriver for the bush-ing has been included in your accessory bag.
Fig. 41 - It is very important to keep themachine free of grit and debris.
Fig. 44 - Your machine will work its bestwhen properly cleaned and lubricated.
Fig. 43 - Due to being spring loaded, therewill be some resistance when pulling thetoolhead off.
Fig. 42 - After removing the clip and discon-necting the rod, replace the clip in the rodfor safe-keeping.
Super 1050, May 2007 5/21/07 12:00 PM Page 14
Casefeed Plunger ConversionWhen changing calibers it may be
necessary to replace the casefeedplunger (#13073*).
To do this, remove the clear casefeedtube (#20533*) and pull out the coloredcasefeed adapter (#13654*). The adapteris taped for shipping purposes.
Remove the two housing screws(#13815) and the casefeed adapter hous-ing (#11006).
Place your hand on the plunger whileremoving the roller bolt (#13333). Thiswill prevent the casefeed plunger andspring from jumping out of the machine.Fig. 45
Thoroughly clean the track and case-feed parts with a solvent. Now verylightly apply grease to the sides andinstall the proper size casefeed plunger(#13073*). Fig. 46 Remember to
grease the roller (#13498) and theroller track (Fig. 46) and Loctite thethreads on the roller bolt (#13333).
Install the casefeed housing and insertthe proper size adapter (#13654*). Thecasefeed tube (#20533*) should now beinserted into the casefeed adapter(#13654*). Note that the tube is marked“up” on one end. Press this end into thetube clip (#13859). See Troubleshootingsection for any adjustments.
Die AdjustmentsStation 2 - To install the size/decap die
Warning: Never attempt to deprimelive primers, an explosion may result.
Move the toolhead down, by loweringthe handle all the way down.
Screw the sizing die into Station 2.Continue to screw the die down until itjust touches the shellplate. Fig. 47
Tighten the die lock ring finger tight.Now move the toolhead up by raisingthe handle to its upright position.
Note: When loading .270 or .30-06you need to raise the decap assembly sothat the hitch pin clip is a minimum of1/8” above the silver lock ring as shownin Fig. 47.
Place a case in the casefeed funnel.Here, the case drops to the casefeedplunger.
Cycle the handle. The casefeed campushes the roller bushing back, droppingthe case into the slot of the plunger.
Cycle the handle. The case is insertedinto the shellplate.
Note: After raising the handle, insurethat you push the handle against its fullaft stop. This will insure that the
shellplate fully advanced to the nextstation.
Note: When priming, pushing thehandle against its stop, will insure thatthe primer is fully seated.
Again, move the toolhead down. Thecase is now sized. If the case has aspent primer, it will be deprimed.Leave the toolhead in this position withthe case fully inserted in the die. Fig.48 This will ensure that the dieremains in alignment when tighteningthe lock ring.
Using a 1" wrench to turn the lockring and a 7/8" wrench to hold the diebody, tighten the lock ring. Station 3 - Adjustment of the Expander
DieInstall the expander die (caliber
specific) at Station 3. Place a case inStation 2 and cycle the operating han-dle once (sending the case to Station3). Turn the expander die down untilyou feel it make contact with the caseand cycle the operating handle. Makeadjustments in one-quarter turn incre-ments until the desired expansion ofthe case mouth is achieved. Tightenthe die lock ring.
A properly expanded case shouldshow a slight flare at the case mouth.Fig. 49
15
Fig. 45 - The casefeed plunger and springare under tension. Hold them in place whileremoving the roller bolt.
Fig. 46 - Be sure to lightly grease the sidesof the casefeed plunger track, casefeedplunger and roller after cleaning.
roller track
Fig. 47 - Screw the size/decap die downuntil it just touches the shellplate.
Fig. 48 - As the toolhead continues down,it will reshape the case neck, shoulderand body.
Super 1050, May 2007 5/21/07 12:00 PM Page 15
Station 5 - Adjustment of the PowderDie/Powder Funnel
Note: Adjusting the powder die fora straight wall case is not the same asadjusting a powder die for a bottle-necked case. This is because straightwall cases are given a bell and bottle-necked cases are not given a bell.
For the powder bar to properly dis-pense a measured powder charge, thepowder bar must travel its full distance.To travel its full distance, the white cubemust contact the powder measure body(see arrow FIG 52).
Also the belling process does notbegin until after the powder bar has trav-
eled its full distance. The angled portionon the bottom of the powder funnel (Fig.53) is what bells the cartridge. Once thewhite cube has contacted the powdermeasure body the case is forced upwardagainst the tapered portion of the pow-der funnel producing a bell. The morethe powder die is adjusted down (clock-wise) the more the case will be belled.
Note: If the powder die is not adjusteddown far enough to cause the powderbar to travel its full distance the powdercharge will be erratic and the case willnot receive enough bell.
Station 5 - Adjustment of the PowderDie/Powder Funnel Cont...
Drop a case into the casefeed funneland cycle the handle twice. The caseshould now be in the shellplate atStation 2.
Move the handle down. Notice theresistance at the end of the down stroke.This is the resistance of the case in thesizing die. Raise the handle. The casewill index to Station 3.
Cycle the handle to advance the caseto Station 4. Again, cycle the handle toprime the case and index it to Station 5.
Cycle the handle.If the white cube has not traveled its
full distance, raise the toolhead justenough to pull the case off of the pow-der funnel (this will prevent theshellplate from indexing while youadjust the powder die). While holdingthe powder measure, turn the die down1/8 of a turn. Again lower the toolheadand observe the travel of the powderbar.
Repeat as needed until the powderbar travels its full distance, Fig. 52.
Once the powder bar travels fullyacross you should continue to adjustthe powder die for the desired amountof bell (turn the powder die 1/8 of aturn at a time). The desired amount bellis just enough to allow the bullet to sit
Fig. 51 - When properly adjusted, thecase mouth will go past the expandingline and the stem will contact the bottomof the case.
Fig. 52 - This photo shows the powder bar atthe end of its travel.
Fig. 53 - Adjusting the powder die upreduces the amount of belling – downincreases the amount of belling.
ACorrect amount
of bell.
BNot enough bell.
CToo much bell.
16
Fig. 49 - You don’t need any more expansionthan what you see in this photograph.
Super 1050, May 2007 5/21/07 12:00 PM Page 16
on the case mouth without falling offand to keep the case from shaving leadduring the seating process - see theillustration (above) example “B”.
Note: If you screw the die down toofar, the case will look like example "C"in the illustration (right). You must thendiscard this case, back the powder dieoff, by turning it counter clockwise, andcontinue with a new sized case.
You’ll soon learn to judge the correctamount of bell by simply looking at it. Inthe meantime, you might want to useyour dial calipers to check it. Twentythousandths of an inch greater (at themouth of the case) than its originaldiameter, should about do it.
Once you’ve achieved the desiredamount of bell – with the case in Station5, raise the toolhead. Run the lock ringdown hand tight.
Insure the bellcrank and the return rodbolt (in the frame) FIG 54 are aligned.Using a 5/32" Allen wrench, snug thecollar clamp screws.
While holding the powder measure inplace, snug the lock ring using a 1-1/8”wrench.
Station 7 - General Information onBullet Seating
The purpose of the seating die is toinsert the bullet into the case and to pushit down into the case the proper amount.
How far the bullet is pushed into thecase will determine the overall length(OAL). Several factors go into determin-ing the proper OAL – such as, the maxi-mum recommended OAL, listed in thereloading manual, and the type of bul-let being loaded. The type of bullet candetermine the OAL in one of two ways.
If the bullet has what is called a can-nelure, or crimping groove Fig. 55 &56, this will determine the proper OAL.If the bullet you’re using doesn’t have acannelure or a crimping groove, thenyou’ll need to refer to your reloadingmanual for the suggested OAL. The pur-pose of the cannelure and crimpinggroove is to secure the bullet by givingthe mouth of the case a place to go(without deforming the bullet) whenbeing crimped. When the bullet isproperly seated, the mouth of the car-tridge case should be near the top ofthe cannelure/crimping groove.
Refer to your reloading manual.Under the section specified for the cal-iber you’re loading, you’ll find aschematic of the cartridge. For example,.38 Special lists a maximum OAL of1.55" (Lyman Reloading Handbook). Ifyou’re seating the bullet to the can-nelure/crimping groove, the OAL shouldbe well within the maximum OAL listed,however, use a set of dial calipers tocheck it. (Dial calipers are available fromDillon Precision). If the bullet you’reusing doesn’t have a cannelure/crimping
groove, refer to the specific type of bul-let you’re using in the reloading manual.For example – if you’re loading a 158 gr..38 Sp. JHP and it doesn’t have a can-nelure/ crimping groove, use the suggest-ed OAL of 1.480 (Lyman ReloadingHandbook).Station 7 - Installation and Adjustment
of the Seating Die
Take the seating die from the die boxand screw it into Station 7. Screw thedie down until the bottom of the die isflush with the bottom of the toolhead.Note: At this point the die will not bescrewed down far enough to begin seat-
17
Fig. 55 & 56 - Shown are several examplesof a cannelure or crimping groove.
Fig. 54 - Make sure the bellcrank and returnrod bolt are aligned.
����������
����������
����������������������
����������
����������
��������������������������
Figure 64
Figure 70
Figure 114
Please note that every die set includesseating stems to fit most common bullettypes. Select the appropriate seating stemfor the bullet type you are loading.
Fig. 57 - Place the bullet on the casemouth at Station 7.
Super 1050, May 2007 5/21/07 12:00 PM Page 17
ing the bullet, but it will give you aplace to start.
Place a case (with a belled casemouth) into Station 7. Fig. 57
Place a bullet on the belled casemouth and lower the toolhead. Then,raise the toolhead just enough to inspectthe bullet without indexing theshellplate. If the bullet is not seated deepenough, screw the seating die down 1/2turn at a time. As a guide, one full turnmoves the die down about 70 thou-sandths of an inch, about the thicknessof a nickel. Again, cycle the machineand inspect the seating depth. Repeatthese steps as necessary until the correctoverall length is achieved. Use a dialcaliper or equivalent to measure theoverall length of the cartridge. Check theoverall length of the round against theinformation in your reloading manual.
Once you have obtained the properOAL, replace the cartridge into Station 7and lower the toolhead. Using a 1"wrench to turn the lock ring and a 7/8"wrench to hold the die body, snug thelock ring.
Note: If you ever load a cartridge thatyou are unhappy with, you can use aDillon bullet puller to reclaim your com-ponents.Station 8 - Installation and adjustment
of the Crimp DieScrew the crimp die into Station 8.
Screw it down until it is flush with thebottom of the toolhead. This is a goodstarting point for the crimp adjustment.
Place a cartridge with a properly seat-ed bullet into Station 8.
Lower the toolhead and continue to
screw the die down until it touches thecartridge. Fig. 58
Raise the toolhead and screw the diedown 1/8 of a turn, lower the toolhead.
Raise the toolhead halfway andinspect the cartridge. If the bell is stillpresent, or the desired amount of crimphas not been achieved, give the die a1/8 turn down and try again. Continuemaking small adjustments to your crimpdie until the desired amount of crimphas been achieved.
Once the adjustment is complete,place the case back into Station 8 andlower the toolhead. Using a 1" wrenchto turn the lock ring and a 7/8"wrench to hold the die body, snug thelock ring.
Note: When adjusting the crimp die itis important to know what to look for.Check that the crimp: Looks OK, allowsyour firearm to function consistently andthe bullet feels tight in the case.
The drawing of case #3 (above) is adepiction of a case that has been overcrimped by adjusting the crimp diedown (clockwise) too far. Note thedefined line below the mouth of the caseand the bulge below the line. This is nota proper crimp. This line is the directresult of the cartridge being overcrimped. A line like this will onlyappear if the crimp die is adjusteddown too far. Warning: Over crimping.45ACP, .38 Super, 9mm, etc., canactually cause the bullet to be loosein the case.
Adjustments for calibers 9mm, .38 Sp.,.45 ACP and for hot loads that have
been fired many timesConfiguration 1
To begin, place a military case (sized,decapped and unswaged) into Station 3.
Screw the back-up rod (#12749*)down two turns into the toolhead(#20420). Pull the handle.
Using a wrench turn the back-up rod
(#12749*) down until it hits the insidebottom of the case. Note: Do not forcethe expander as this will damage thecase and the shellplate. Now secure thelock ring (#14062). Raise the handle.
Screw the eyebolt (#13245) all theway into the swager. Grease the clevispin (#13522) heavily.
Put the swager into position. Push theclevis pin through the connecting rodand eyebolt and secure with the hitchpin (#13840). Replace the swage cover(#13064).
With the military case still inStation 3, pull the operating handledown with your left hand. Now turnthe swager upward with your righthand until it meets resistance. Withyour left hand raise the operating han-dle about 10 inches. With your righthand turn the swager up a 1/4 turn.Cycle the handle down.
Raise the handle just enough toremove the case and inspect the primerpocket to see the amount of swagingbeing done. The swager should leave aradiused entrance on the primer pock-et. Fig. 59
Turn the swager in, using 1/4 turnincrements until you achieve the prop-er swage. Secure the jam nut (#13682).Note: Do not over swage. This condi-tion will cause damage to theshellplate (#12600*).
When your swager is properly adjust-ed you will feel resistance during thefinal 1/2" to 1" of the downward strokeof the handle.
Adjustments for rifle calibersConfiguration 2
To begin, place a military case (sized,decapped and unswaged) into Station 3.
Remove the back-up rod (#12749*)from the back-up die (#12184).
With the operating handle in thedown position, screw the back-up dieinto Station 3 until the die comes intocontact with the shellplate. Now back
18
Fig. 58 - Cutaway crimp die shows thearea being crimped while the case isbeing fully supported by the die body.
Fig. 59 - Note the difference between theswaged primer pocket (left) and theunswaged primer pocket (right).
���������
��������������������������������
����������
����������
����������������������
����������
����������
Figure 64
Figure 70
Figure 114
321
Super 1050, May 2007 5/21/07 12:00 PM Page 18
the die out one full turn and secure it inplace with the lock ring (#14067).
Leave the handle in the down posi-tion. With a wrench, screw the back-uprod into the back-up die. Turn theback-up rod down until it touches theinside bottom of the case. Note: Donot force the expander as this willdamage the case and the shellplate.Now secure the lock ring (#13483).Raise the handle.
Screw the eyebolt (#13245) all theway into the swager. Grease the clevispin (#13522) heavily.
Put the swager into position. Push theclevis pin through the connecting rodand eyebolt and secure with the hitchpin (#13840). Replace the swage cover(#13064).
With the military case still in Station3, pull the operating handle down withyour left hand. Now turn the swagerupward with your right hand until itmeets resistance.With your left handraise the operating handle about 10inches. With your right hand turn theswager up a 1/4 turn. Cycle the handledown.
Raise the handle just enough toremove the case and inspect the primerpocket to see the amount of swagingbeing done. The swager should leave aradiused entrance on the primer pock-et. Fig. 59
Turn the swager in, using 1/4 turnincrements until you achieve the properswage. Secure the jam nut (#13682).Note: Do not over swage. This conditionwill cause damage to the shellplate(#12600*).
When your swager is properly adjust-ed you will feel resistance during thefinal 1/2" to 1" of the downward strokeof the handle.
RL1050 vs. Super 1050Not all parts are the same but some
are still interchangeable. We have madechanges to several parts used on theSuper 1050 that are not interchangeablewith the RL1050 machine.• The Super 1050 primer lever assembly
(#21145) has a longer arm to accom-modate the higher toolhead travel. Thisis not available for RL 1050 machines.Primer feed body (#20773) will fit bothmachines but again the primer leverassembly will not.
• The Super 1050 index lever has been
changed considerably and will notindex properly on RL 1050 machines.
• The Super 1050 mainshaft, mainshaftpivot pin, crankshaft assembly, andbearings are completely different.
• The casefeed body has been modifiedto allow long cases to feed throughbut is interchangeable between theSuper 1050 and RL 1050 machines.
• Any RL 1050 toolhead assembly willfit the Super 1050 machine, but thetoolhead ratchet (#11686, RL 1050)must be replaced with ratchet(#11688, Super 1050).
• The toolhead spring, bushing andsleeve, as a set, are longer to accom-modate the increased toolhead travelon the Super 1050 but they willwork on the RL 1050.
• The RL 1050 spent primer cup hasbeen replaced with a larger, plasticspent primer cup and bracket. It is notinterchangeable.
Using RL 1050 toolheads anddies on the Super 1050...
If you want to interchange an RL 1050toolhead already set for a caliber youwant to load onto the Super 1050 youwill need to check for the followingclearances.
1. Remove the toolhead assemblyfrom the Super 1050.
2. Replace the shellplate with theshellplate for the caliber you intend toload with.
3. Remove the toolhead spring and setthe toolhead onto the mainshaft whileholding the handle at about mid-travelfor proper alignment into the frame.Next, install the washer and toolheadbolt.
4. Slowly lower the handle and lookto see if any die comes in contact withthe shellplate. Readjust dies as needed.
5. Place one unprimed case in theswage station and again slowly lower thehandle. Readjust the expander andswage rod as needed.
6. Once you have reset the dies to themachine, remove the toolhead and rein-stall the toolhead spring and completethe rest of the conversion and set up toreload. Reinstall the toolhead.
Troubleshooting .308 Winchester and related calibers
with similar case length (.243 and/or.22-250) also lend themselves to reload-
ing on this new machine. No specialchanges are necessary to the die set.
Hard or Incomplete Indexing1.) Wrong size locator buttons.
2.) Index pawl bent or worn (#13705).
3.) Shellplate lock ring adjusted tootightly (#20311).
4.) Dirt under the shellplate (#12600*).
5.) Bent or broken shellplate (#12600*).
6.) Ejector tab (#13189) interfering withthe shellplate - see above photo.
Station 1: Case Insertion Problems1.) Wrong size case insert plunger(#13073*).
2.) Wrong case insert adapter (#13654*).
3.) Shellplate lock ring not adjusted tightenough.
4.) Dirt in the shellplate (#12600*) pock-ets or damaged shellplate.
5.) Handle being moved too rapidly onupstroke.
6.) Bent or broken roller bolt (#13333).
7.) Dirt or media in casefeed track.
Station 2: Resizing and Decapping Problems
With .30-06 and .270 calibers it isimportant to note that the seater andcrimp dies must be shortened for clear-ance reasons. They are available and areincluded with the respective conversionkits.
1.) Crushed cases:a.) Shellplate lock ring too loose or
too tight. b.) Not enough radius on the die. Use
19
When reinstalling the ejector tab (#13189) itis vital that it is not set too low or it willinterfere with the shellplate.
Super 1050, May 2007 5/21/07 12:00 PM Page 19
Dillon dies whenever possible.c.) Wrong size or missing locator but-
tons.
2.) Bending or breaking decapping pins:a.) Wrong shellplate (#12600*).b.) Slightly bent decapping assembly
or pin.c.) Berdan primed cases.d.) Dirt in shellplate pockets.e.) Handle being moved too rapidly
on the down stroke.f.) Rocks or other foreign objects in
cases.Station 3: Primer Pocket Swaging
Problems1.) Primers smearing or crushing:
a.) Swage back-up rod not down farenough (#13332 or #13348).
b.) Swage rod not adjusted highenough (#20314 - large or #20313 -small).
Station 4: Priming Problems
The above photo shows the rockerarm set screw (#13226) being adjusted.The Super 1050 comes from the factorywith this set screw properly adjusted, butover time it can move. When the rockerarm set screw is out of adjustment, it candent primers and/or cause the primerslide to stick. When properly adjusted,the primer punch (#12849 large -#13307 small) will be flush with theplatform surface – see arrow above.1.) Crushed primers:
a.) Swage rod (#20314 - large or#20313 - small) not adjusted correctly,dirty or worn out.
b.) Dirt in the shellplate (#12600*).c.) Ringed primer. When a spent
primer has been pierced by the decap-ping pin leaving a ring of metal from theprimer in the pocket.
d.) Primer station retain tab (#12930)not adjusted correctly.
e.) Worn primer punch (#12849).f.) The bench that the machine is
mounted on is not rigid enough. This canbe corrected by affixing a board to boththe wall and your bench.
g.) Hot-loaded ammo that has beenfired several times and the base of thecase has been flattened out.
2.) High primers:a.) Adjust the primer push rod
(#12819).b.) On .223 cases the swage back-up
rod (#13332) is down too far, slightlycollapsing the primer pocket and notallowing the primer to seat fully.
c.) Loose shellplate (#12600*).d.) Erratic handle motion.e.) Do not remove the rubber piece on
the primer slide.
3.) Smeared primers - see Station 3:Primer Pocket Swaging - item 1
4.) Locator tab:a.) When adjusting the priming sta-
tion locator tab, it should be set asclose to the case as possible withouttouching it. Be sure the cases in theshellplate rotate freely past the tab.Change primer magazine tips every20,000 rounds. Note: Move the handledown, bringing the toolhead down.Move the locator tab in to the case inthe priming station.
Station 5. Powder and Case MouthBelling Problems
1.) Crushing cases:a.) Wrong size or missing locator
buttons.
2.) Spilling powder:a.) Slamming or going too fast with
the operating handle (#17071).b.) Stick or pencil-lead type powders
bridging on the case mouth in the pow-der funnel (#13005). See conversionchart.
c.) Check powder bar adjustment.
3.) Erratic belling:a.) Variation in case length. Divide
cases by brand.b.) Handle not moving all the way
down on each stroke. Note: Try setting abullet on the case mouth in Station 6.
4.) Erratic powder charges:a.) Powder bar not moving full length
of its travel. Turn the powder die downuntil it does.
Station 7: Bullet Seating Problems1.) Erratic seating depth of the bullet:
a.) Build up of lead shaving and/orlube in the seater or crimp dies.
b.) Bullets having erratic dimension(length and/or the ogive).
c.) Use the proper seating stem for thetype of bullet being used.
d.) Variations in case types and/or lots– sort brass.
e.) Refer to a loading manual for prop-er loaded length (OAL) and additionalinformation.
Station 8: Crimping Problems1.) Erratic crimping:
a.) Length of cartridge cases erratic,probably due to mixed brands of brass.
b.) Worn out or improperly made die,use Dillon dies whenever possible.
2.) Loose bullet:a.) Too much taper crimp. Note, this
condition also ruins accuracy.b. Wrong expander (#12749*).c.) Thin cases.
MaintenanceLoctite
Loctite should be used followingadjustments to or replacement of allthreaded screws. Please note that Loctiteshould be applied to threaded portionsonly and should be of a non-permanenttype. Blue Loctite #242 is recommended.
SwageClean the swage by pulling the operat-
ing handle down and use a small brushto clean the tip. Every 10,000 rounds,remove the swage rod (#20314 - largeor #20313 - small). and clean, lightlygrease and replace. Note: Do not greasethe tip of the swage where it contacts theprimer pocket.
20
primer punch
Super 1050, May 2007 5/21/07 12:00 PM Page 20
21
LubricationOperating circumstances will dictate
the frequency of required lubrication. Itis highly recommended that the Super1050 be cleaned and lubed after every10,000 rounds of operation.
Use a high-grade, conventional wheelbearing grease – do not use oil.
Lubrication Points:
• Casefeed Plunger (#13073*), lube thesides and bottom.
• Casefeed Plunger Roller (#13498) andBolt (#13333)
• Tappet (#12995)• Rocker Arm (#13058), cam surfaces
and hole.• Pivot Bolt (#13296)• Primer Punch Base (#12849 - large or
#13307 - small)
• Lube the Indexing Lever Cam surface(#10064) and Index Lever ShoulderBolt (#13276). With the handle in therest position, you will see the IndexRoller (#10996) come into contactwith the Lever Cam surface. TheIndex Roller (#10996) also requiresperiodic lubrication.
• Alignment Pins (#12972 & #13515located under the toolhead)
• Cam Guide Bolt (#12486) and itsmated slot
• Toolhead Bore (#20420 - lightly toavoid rusting and/or freezing up)
• Mainshaft Lubrication – Use only 30weight motor oil. DO NOT use apenetrating lubricant such as WD-40,Breakfree, etc…
• Swage Connecting Rod (#13417) andClevis Pin (#13522)
• Shellplate lock ring (#20311), bottomsurface to shellplate face.
• Shellplate center hole. It’s easiest tolubricate the shellplate center holewhen changing from one caliber toanother.We recommend that you use a droplet
of Blue Loctite on the threads of the fol-lowing bolts prior to reinstalling:#13333, #13296, and #13276 (see pho-tos and schematics).
casefeed plunger(caliber specific)
13498
13333
12995
13296
13058
12849large
or13307small
75% - 50% - 75% - 75%
12486
alignment pin
Super 1050 mainshaft10999
toolhead bore
alignmentpin casefeed cam
13417
13522
13276
11064
operating handle shown indown position
20311
Super 1050, May 2007 5/21/07 12:00 PM Page 21
22
10999
11061
11008
10997
10994
11008
11008
11062
13685
11010
13365
11063
11009
Lube Points for the Super 1050Crank Assembly
With the handle in the rest position,on the left side of the machine, use agrease syringe to lube the bearing pin(#11009) located in the link arm(#11063). Then, cycle the handle downto the bottom stop.
Again, using the grease syringe, lubethe mainshaft pivot pin (#10994) onthe left side of the machine via theaccess hole located 1.2" above the car-rier cap (#11010).
Use 30 weight motor oil on the main-
shaft (#10999).Towards the back of the machine,
lube the indexing lever cam surface(#11064) and index lever shoulderbolt (#13276).
When it is time to lube the roller bear-ings (#11008) in the frame and crank-shaft, first remove the swage rod assem-bly, swage connecting rod, and operatinghandle. On the left side of the machine,use a 5/32" Allen wrench to remove thescrew (#13685). Slide the carrier cap(#11010) out of its bore and lube theleft-hand side roller bearing (#11008)and carrier cap. Next, slide the crank-
shaft (#11061) out of the frame from theright side of the machine BUT NOMORE THAN 3/4". Using a greasesyringe, dispense some grease onto theright-hand side roller bearing (#11008).Next, lube the crankshaft surface(#11061). Then, reinsert the crankshaftfully into the frame. Reinstall the carriercap (#11010). Blue Loctite must be usedon the threads before installation, tight-en. Finally, reassemble the swage com-ponent and operating handle back ontothe frame. Lube the swage connectingrod (#13417) and clevis pin (#13522).
Super 1050, May 2007 5/21/07 12:00 PM Page 22
23
NOTES:
Super 1050, May 2007 5/21/07 12:00 PM Page 23
24
Super 1050 - Caliber Conversion Chart.32 ACP Conversion - #20634 11113 #J Shellplate14048 #8 Locator Pin (6)12780 .32 cal. Expander - S12845 Powder Funnel - S13810 Adapter - White13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring.32 S&W Long/H&R Mag Conv - #20634 12107 #D Shellplate14060 #3 Locator Pin (6)12780 .32 cal. Expander - S12845 Powder Funnel - S13878 Adapter - Green13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring.380 Auto Conversion - #20483 12441 #3 Shellplate14060 #3 Locator Pin (6)13285 .380 cal. Expander - F13810 Adapter - White12964 Casefeed Plunger - Small .38017384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13419 1/4 x 28 Jam Nut13017 Swage Back-up Rod - Large12184 Swage Die13483 9/16 x 18 Lock Nut13005 Powder Activator - Pistol9mm Conversion - #20482 12938 #5 Shellplate14060 #3 Locator Pin (6)12833 9mm cal. Expander - F13878 Adapter - Green13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.357 SIG Conversion - #2006812940 #W Shellplate14062 #2 Locator Pin (6)12833 9mm cal. Expander - F13878 Adapter - Green13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.38 Super Conversion - #2048412938 #5 Shellplate14060 #3 Locator Pin (6)12833 9mm cal. Expander - F13878 Adapter - Green13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol
.38 Super Comp Conv. - #2106912441 #3 Shellplate14060 #3 Locator Pin (6)12833 9mm cal. Expander - F13878 Adapter - Green13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.38 Special/.357 Mag. Conv. - #2047712704 #2 Shellplate14062 #2 Locator Pin (6)13137 .38/.357 cal. Expander - D13802 Adapter - Orange13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol9x25 Dillon Conversion - #2152512940 #W Shellplate14062 #2 Locator Pin (6)12833 9mm cal. Expander - F13872 Adapter - Red13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.40 S&W Conversion - #2054512940 #W Shellplate14062 #2 Locator Pin (6)12912 10mm cal. Expander - W13878 Adapter - Green13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol10mm Auto Conversion - #2078812940 #W Shellplate14062 #2 Locator Pin (6)12912 10mm cal. Expander - W13872 Adapter - Red13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.38-40 Conversion - #2116016153 1050 #N Shellplate14047 #4 Locator Pin (6)13600 Powder Funnel W - Pistol13654 Adapter .41 Mag, .44, .45 LC13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5).41 Magnum Conv. - #2047811856 #6 Shellplate13930 #1 Locator Pin (6)12882 .41 cal. Expander - H13654 Adapter - Yellow13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol
.44-40 Conversion - #2116116153 1050 #N Shellplate14047 #4 Locator Pin (6)13474 Funnel .44-4013654 Adapter .41 Mag, .44, .45LC13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5).44 Special/Magnum Conv. - #2047912600 #4 Shellplate14047 #4 Locator Pin (6)12628 .44 cal. Expander - G13654 Adapter - Yellow13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.45 GAP Conversion - #2101012999 1050 #1 Shellplate13930 #1 Locator Pin (6)11118 1050 .45 GAP Expander13842 .45 GAP Casefeed Adapter13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.45 ACP Conversion - #2048012999 #1 Shellplate13930 #1 Locator Pin (6)12749 .45 cal. Expander - E13872 Adapter - Red13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.45 Colt Conversion - #2048111235 #C Shellplate14047 #4 Locator Pin (6)12749 .45 cal. Expander - E13654 Adapter - Yellow13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13005 Powder Activator - Pistol.475 Linebaugh/.480 Ruger Conv. - #2083316153 1050 #N Shellplate15755 #6 Locator Pin (6)10723 Powder Funnel .475/.480 Ruger11089 Super 1050 .475/.480 Adapter13072 Casefeed Plunger 45-7017384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13443 Large Powder Die - Part20534 1050 Mag CF Tube, Red21075 Casefeed Plate - Large Rifle22174 Casefeed Funnel Assembly - Lg(Requires Extra Large Powder Die - #21253)
Super 1050, May 2007 5/21/07 12:00 PM Page 24
.500 S&W Conversion - #2083411036 .500 S&W 1050 Shellplate13436 #7 Locator Pin (6)14465 Powder Funnel, .50 AE11090 Super 1050 .500 S&W Adapter13072 Casefeed Plunger - Extra Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring13443 Large Powder Die - Part20534 1050 Mag CF Tube, Red21075 Casefeed Plate - Large Rifle22174 Casefeed Funnel Assembly - Lg(Requires Extra Large Powder Die - #21253).223 Remington Conversion - #2048512441 #3 Shellplate14060 #3 Locator Pin (6)13332 Back-up/Expander .22313426 Powder Funnel - A12146 Adapter (pinned) - White, Long13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.22-250 Conversion - #2105512999 #1 Shellplate13930 #1 Locator Pin (6)12071 1000/1050 .22-250 Expander13426 Powder Funnel - A, Rifle11005 Super 1050 Adapter - .308 Win13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.243 Winchester Conversion - #2105412999 #1 Shellplate13930 #1 Locator Pin (6)12070 1000/1050 .243 Expander13305 Powder Funnel - I, Rifle11005 Super 1050 Adapter - .308 Win13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut6.5 Grendel Conversion - #2089611925 #A Shellplate14062 #2 Locator Pin (6)18947 Powder Funnel 6.5 Grendel12943 Adapter - 7.62x3913098 Casefeed Plunger - Medium13703 Casefeed Spacer17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring
.270 Winchester Conversion - #2105312999 #1 Shellplate13930 #1 Locator Pin (6)12069 1000/1050 .270 Expander13456 Powder Funnel - J, Rifle11004 Super 1050 Adapter - .30-0613098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.30 Carbine Conversion - #2062612655 #8 Shellplate14048 #8 Locator Pin (6)12748 .30 M1 Expander - C13564 Powder Funnel C12641 Adapter - White, Slotted13306 Casefeed Plunger - Small17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring.30-30 Conversion - #2105212075 #7 Shellplate14047 #4 Locator Pin (6)12068 1000/1050 .30-30 Expander13587 Powder Funnel - B, rifle11005 Super 1050 Adapter - .308 Win13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.308 Win./7.62x51 Conversion - #2104912999 #1 Shellplate13930 #1 Locator Pin (6)12074 Back Up Expander - .30813587 Powder Funnel - B, rifle11005 Super 1050 Adapter - .308 Win13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.300 WSM Conversion - #2046618497 #B Shellplate 13436 #6 Locator Pin (6)12074 Back Up Expander - .30818415 Powder Funnel, Short - .300 Mag.11459 1050 Adapter - .300 WSM13072 Casefeed Plunger - Extra Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut11458 1050 Casefeed Body - Magnum(Requires Extra Large Powder Die - #21253)
.30-06 Conversion - #21050(only conversion kit that includes dies)10840 .30-06 Die Set12999 #1 Shellplate13930 #1 Locator Pin (6)12073 Back-up Expander - .30-0613587 Powder Funnel - B, Rifle11004 Super 1050 Adapter - .30-06 13098 Casefeed Plunger - Medium17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut7.62 x 39 Conversion - #2063111925 #A Shellplate14062 #2 Locator Pin (6)13348 Back Up Expander - 7.62 x 3913015 Powder Funnel AK12943 Adapter13098 Casefeed Plunger - Medium13703 Casefeed Spacer17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.303 British Conversion - #2105116153 #N Shellplate14047 #4 Locator Pin (6)13348 Back Up Expander - 7.62 x 3913587 Powder Funnel - B, rifle13654 Super 1050 Adapter - .41 Mag.,.44, .45 LC13073 Casefeed Plunger - Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut.45-70 Conversion - #2105612705 1050 Custom #G Shellplate 13436 #7 Locator Pin (6)12072 1000/1050 .45-70 Expander13407 Powder Funnel - T, pistol11007 Super 1050 Adapter - .45-7013072 Casefeed Plunger - Extra Large17384 Blue Locator Tab - Short (1)13569 Blue Locator Tab (5)14067 Die Lock Ring12184 Swage Die Body - Part13483 9/16 x 18 Lock Nut20773 Primer Feed Body/Shield20534 1050 Mag CF Tube Red
Super 1050 - Caliber Conversion Chart
25
Super 1050, May 2007 5/21/07 12:00 PM Page 25
26
Super 1050 Parts ListingPart # Description10851 Index Lever, Super 1050B10991 Bin Support Bracket10992 Inside Frame Stop10993 Spent Primer Cup Bracket10994 .560 dia. Mainshaft Pin10997 Super 1050 Frame10999 Mainshaft11003 Lever Arm11006 Casefeed Housing11008 BH-1610 Roller Bearing11009 1.00” dia. Pin11010 Carrier Cap11011 Super 1050 Manual11061 Crank Shaft11062 Crank Arm11063 Link Arm11064 1050 Index Lever Assembly11234 Lock Link Assembly11335 Spring Bushing11423 Casefeed Funnel 550/650/1050 part11688 Toolhead Ratchet11995 Index Lever rev. 212144 Bullet Bin Bracket12184 Swage Die Body – Part12260 1050 Box For Shipping12486 Cam Guide Bolt 1/4x2012572 Toolhead Spring12819 Primer System Push Rod12930 Primer Station Retain Tab12972 Toolhead Alignment Rod12995 Primer System Tappet13001 New Lever Arm Bracket13058 Primer System Rocker Arm13064 Swage Cover 105013089 Return Rod Eye Bolt13091 Alignment Bushing – New13108 Primer Slide Stop “B”13161 Casefeed Cam105013189 1050 Ejector Tab13205 Post Bolts13226 Rocker Arm Set Screw13238 Bin Bracket13244 Crank Retaining Pin (2)13245 Primer Swage Adjustment Bolt13262 7/32” Hex Wrench (Short)13271 Post Stud13276 Index Lever Shoulder Bolt13296 Primer System Rocker Bolt13328 1/4-20 Shoulder Bolt13333 Locator Tab Bolt13342 Toolhead Bolt13363 Primer Magazine Socket Bolt13365 Index Roller13376 Ratchet Restriction Tab13377 Bin Bracket Mount Screw13417 Swage Connecting Rod13419 Swage Rod Lock Nut13425 1050 Shellplate Nut13432 Crank Handle Lock Screw13435 1/4” Hex Wrench
13449 Toolhead Washer13475 Journal Key 105013483 Old Style Jam Nut 9/16x1813484 1050 Cartridge Bin13495 Lower Cord Clamp13498 Plunger Roller 105013502 Clamp Retaining Screw13508 Index Ball 105013515 Slide Alignment Pin13522 Clevis Pin13525 Index Ball Spring 105013561 Lock Ring Insert13567 Casefeed Plunger Spring13569 Blue Locator Tabs13581 Grease Fittings13593 5/32” Hex Wrench13607 Rocker Bolt Lock Washer13611 Casefeed Post Warning Label13624 Index Pawl Spring13644 Small Powder Bar Spacer13655 5/16 Washer13664 5/16-18 Nut13682 Swage Lock Nut 105013685 1/4-20x1/2 Bracket Bolt13696 3 Packing Foam Pieces13701 Index Pawl Pin 3/813705 1050 Index Pawl13719 8-32 x 3/8” BHCS13728 1/8” Hex Wrench13738 #10 Washer for Roller13746 Actuating Lever Cotter Pin13756 1050 Bullet Bin13793 Collar Roller13799 Strip Nut13801 Tinnerman Insert13813 Clutch Spring Washer13815 Adapter Housing Screw13818 Powder Bar Insert – Small13827 3/16” Hex Wrench13840 Hair Pin Cotter13844 Short Lever Spring13845 Body Collar Sleeve13848 Bellcrank Bushing13853 Powder Bar Insert – Large13858 Primer Punch Spring 105013859 Casefeed Tube Clip13871 Bellcrank Cube13882 Powder Measure Lid13886 3/32” Hex Wrench13888 E-Clip13893 Powder Bar Post – Large13895 10-24 x 3/8” BH Screw (7)13896 1/4-20 3/8 BH – Ejector Tab Screw13904 Bellcrank Bolt13921 Powder Bar Spacer Plug13929 Return Rod Clip13936 Tab/Spring Arm Spring13939 Body Collar Clamp – Part13943 Powder Bar Adjustment Screw13944 Indexer Return Spring13945 5/16” Bowed Washer
13951 Powder Bar Post – Small13955 Lower Plate Screw13957 Magazine Shield Cap 105013958 Powder Bar Bolt Washer13960 Powder Bar Return Rod – Part13964 10-24x1/4 BHCS for Index Roller13972 3/16 Roll Pin14003 Magazine Orifice – Large – Red14023 10-24 5/8 Buttonhead Screw14024 Magazine Orifice – Small – Blue14033 Return Rod Spring14036 Old Powder Bar Return Spring 14037 10-24x3/4 SHCS –
Collar Clamp Screw (2)14067 Die Lock ring14202 Powder Measure Tube Screw14517 Swage Station Bushing14808 Collar Roller Bushing14990 Slide Roll Pin Sleeve16699 Spent Primer Cup17069 Snap Ring17071 1050 Roller Handle Assembly17141 1/4” Hardened Washer17384 Blue Locator Tab, Short17604 Bracket Pivot Pin17808 Casefeed Bowl Insert18492 Casefeed Plate, Extra Large Rifle20062 Small Powder Bar Assembly20063 Large Powder Bar Assembly20311 1050 Lock Ring Assembly20313 Swage Rod 1050 – Small20314 Swage Rod 1050 – Large20317 1050 Primer Slide – Small20318 1050 Primer Slide – Large20320 Powder Die20341 1050 Bushing Driver20419 1050 Primer System – Small20420 1050 Toolhead Assembly22221 Super 1050 Auto Powder System20476 1050 Primer System – Large21108 Super 1050 Primer Arm/Cam –
Assembly20533 Casefeed Tube, small - black label20534 Casefeed Tube, large - red label20635 Ratchet Detent Assembly20641 Casefeed Mounting Post – Assembly20773 Primer Feed Body/Shield20785 Powder Measure Body21072 Casefeed Plate – Large Pistol21073 Casefeed Plate – Small Pistol21074 Casefeed Plate – Small Rifle21075 Casefeed Plate – Large Rifle21275 Body Collar – Complete97073 650/1050 Casefeed Assembly (Euro)97074 650/1050 Casefeed Assembly
Super 1050, May 2007 5/21/07 12:00 PM Page 26
27
75% - 50% - 75% - 75%
Super 1050 Upper Machine Assembly
#17071 – Handle Assembly
17918
12727
11061
13432
17069
11061
#20420 – Toolhead Assembly
13342
13449
20420
13957
20773
13955
13108
13376
13945
1332813936
13276
13705
13624
13944
12930
13895
16699
13895
10993
13896 13189
13525
13508
13226
13089
13425
2063511335
12572
13895
13561
*Locator Pins and Tabs
See page 29 formore detail.
12819
powder activatorsee caliber
conversion chart
20320Seating
Die
SizingDie
14067
10999
13161 13896
12486
11688
11688
CrimpDie
11064assembly
20311assembly
*Shellplate20317 – small20318 – large
Expandersee caliberconversion
chart
* Indicates a caliber specific part -see the caliber conversion charts onpages 24 & 25 for the caliber youare loading.
Super 1050, May 2007 5/21/07 12:00 PM Page 27
10999
11061
1347511008
10997
11062
11008
1324411009
10994
13244
11063
11008
13685
11010
1389513738
13365
14517
20313 - small assembly20314 - large assembly
13064
1389613682
13245
13417
13581
13840
13522
See page 31 – CasefeedFrame Assembly
SeeItem Aabove
Super 1050 Lower Machine Assembly
Item A – Swage Rod AssemblyLower Machine AssemblyPart # Description10994 Mainshaft Pivot Pin - .560” dia.10997 Super 1050 Frame10999 Super 1050 Mainshaft11008 BH-1610 Roller Bearing (3)11009 Pin - 1” dia.11010 Carrier Cap11061 Crankshaft11062 Crankarm11063 Link Arm13244 Crank Retaining Ring (2)13328 1/4-20 Shoulder Bolt13365 Index Roller13376 Ratchet Restriction Tab13475 Journal Key13685 1/4-20x5/8 BHCS13738 #10 Washer13895 10-24x3/8 BHCS13936 Tab/Spring Arm Spring13945 5/16” Bowed Washer
Item A – Swage Rod AssemblyPart # Description13064 Swage Cover 105013417 Swage Connecting Rod13522 Clevis Pin13581 Grease Fittings13840 Hair Pin Cotter13896 1/4-20 3/8 BH Ejector Tab Screw14517 Swage Station Bushing20313 Swage Rod Assembly – Small:
13127 Swage Rod (1050) – Small13245 Primer Swage Adjustment Bolt13682 Swage Lock Nut 1050
20314 Swage Rod Assembly – Large:13245 Primer Swage Adjustment Bolt13364 Swage Rod (1050) – Large13682 Swage Lock Nut 1050
13376
13945
13328
13936
28
Super 1050, May 2007 5/21/07 12:00 PM Page 28
���������
Primer System Assembly - #21108
Upper Lower
13957 13840
14037
13001
20488
11003
17604
13844
13936
13746
20773
13363
13363
12995
13130 - large13222 - small 13423
14990
13858
13058
13607
13296
12849 - large13307 - small
20317 - small20318 - large
22030 - small22031 - large Upper Assembly
Stock Description13957 Magazine Shield Cap20773 Primer Feed Body/Shield22030 Primer Magazine Tube – Small22031 Primer Magazine Tube – Large21145 Primer Arm/Cam Assembly
11003 Slide Actuating Lever13001 New Lever Arm Bracket13746 Actuating Lever Cotter Pin13840 Hair Pin Cotter13844 Short Lever Spring13936 Tab/Spring Arm Spring14037 Clutch/Motor Bolt17604 Bracket Pivot Pin
Lower AssemblyStock Description12849 1050 Primer Punch – Large12995 Primer System Tappet13058 Primer System Rocker Arm13130 Primer Punch Bushing – Large13222 Primer Punch Bushing – Small13296 Primer System Rocker Bolt13307 1050 Primer Punch – Small13363 Primer Magazine Socket Bolt13607 Rocker Bolt Lock Washer13858 Primer Punch Spring 105020317 Primer Slide Assembly – Small
13237 Primer Slide 1050 – Small13423 Roll Pin – 1/8x5/814990 Slide Roll Pin Sleeve
20318 Primer Slide Assembly – Large13105 Primer Slide 1050 – Large13423 Roll Pin – 1/8x5/814990 Slide Roll Pin Sleeve
29
Super 1050, May 2007 5/21/07 12:00 PM Page 29
Stock # Description10991 Bin Support Bracket11423 Casefeed Funnel 550/650/1050 Part12144 Bullet Bin Bracket13205 Post Bolts13238 Bin Bracket13271 Post Stud13377 Bin Bracket Mount Screw13400 Casefeed Bowl 105013473 Casefeed Motor – 4 RPM
(Not Shown)13484 1050 Cartridge Bin13495 Lower Cord Clamp13502 Clamp Retaining Screw13539 Casefeed Cord Set13540 Casefeed Motor Cover13655 5/16 Washer13685 1/4 - 20 x 5/8 BHCS13756 Bullet Bin13779 Micro-Switch (Not Shown)13812 Lighted Power Switch13859 Casefeed Tube Clip13895 10-24 BH Screw (Not Shown)13954 Micro-Switch Mount Screw
(Not Shown)14022 Casefeed Motor Roll Pin
(Not Shown)14023 10-24 5/8 Buttonhead Screw
(Not Shown)14026 8-32x1/2 Bowl/Motor Screw
(Not Shown)17808 Casefeed Bowl Insert 20533 Casefeed Tube, small -
black label20534 Casefeed Tube, large -
red label20641 Casefeed Mounting
Post Assembly22173 Casefeed Funnel
Assembly (Small)22174 Casefeed Funnel
Assembly (Large)
Super 1050 Casefeeder Assembly
13400
17808
11423
13859
1381213540
*20533/*20534
13756
20641
13539
13205
13484
1337713685
12144
10991
1365513238
1327113495
* Indicates a caliber specific part – see the caliber conversioncharts on pages 24 & 25 for the caliber you are loading for.30
Super 1050, May 2007 5/21/07 12:00 PM Page 30
Super 1050 Casefeed Subassemblies
Casefeeder ClutchAssemblyStock # Description13632 Upper Clutch13655 5/16 Washer13703 Spacer (.41, .44, .45LC,
.357, .30 Carbine)13732 Clutch/Motor Bolt13736 Lower Clutch13813 Clutch Spring Washer*21072 Casefeed Plate
(Large Pistol)*21073 Casefeed Plate
(Small Pistol)*21074 Casefeed Plate
(Small Rifle)*18420 Casefeed Plate
(XL Rifle)
Item A – CasefeedFrame AssemblyStock # Description13333 Bolt (Locator Tab)13498 Plunger Roller11006 Adapter Housing13567 Casefeed Plunger Spring13815 Adapter Housing Screw13972 3/16 Roll Pin
* Indicates a caliber specific part – see the caliber conversioncharts on pages 24 & 25 for the caliber you are loading for.
*21072
13732
13655 (4)
13813
13632
13703
13736
Adapter – refer to the caliberconversion chart
Casefeed Plungerrefer to the cal-iber conversion
chart
13815
138821395113644
13943
20062
1389321353
20785
14202
16340
13940
13793
14808
13845
13089
14033
13799
13801
20320
*13005*13426
13960
14023
14037
13939
14202
20063
1123413871
1404113848
13904
13929
11006
13567
13972
13498
13333
2078013921
frame
Stock # Description11234 Lock Link Assembly*13005 Powder Activator, Pistol13089 Return Rod Eye Bolt*13426 Powder Funnel “A”, Rifle13644 Small Powder Bar Spacer13793 Collar Roller13799 Blue Strip Nut13801 Tinnerman Insert13818 Powder Bar Insert, Small13845 Collar Sleeve13848 Bellcrank Bushing13853 Powder Bar Insert, Large13871 Bellcrank Cube13882 Powder Measure Lid13893 Powder Bar Post, Large13904 Bellcrank Bolt13921 Powder Measure Plug13929 Return Rod Clip13939 Collar Clamp13940 Body Collar Housing – Part
Stock # Description13943 Powder Bar Adjust. Screw13951 Powder Bar Post, Small13958 Powder Bar Bolt Washer13960 Powder Bar Return Rod –
Part14023 8-32x3/4 BH Screw14033 Return Rod Spring14037 Collar Clamp Screw14041 Bowed Washer14202 Powder Measure Tube Screw14808 Collar Roller Bushing16340 10-32 Nylon Lock Nut20062 Powder Bar, Small20063 Powder Bar, Large20320 Powder Die20780 Powder Bar, Extra Small20785 Powder Measure Body21275 Body Collar – Complete21353 Powder Bar, Magnum
31
Powder Measure Assembly - #20421
Super 1050, May 2007 5/21/07 12:00 PM Page 31
Dillon Precision Products, Inc.8009 E. Dillon’s Way • Scottsdale, AZ 85260
(480) 948-8009 • FAX (480) 998-2786
Web Site: www.dillonprecision.comE-mail: [email protected]
Technical Support & Customer Service(800) 223-4570
On the cover…The Super 1050 is pictured with optional accessories:Powder Check System #21044Low Powder Sensor #16306Bullet Tray #22215
Other accessories available for the Super 1050 include:Machine Cover #13239Maintenance Kit & Spare Parts Kit #97018
The Blue Press, Dillon’s monthly catalog, has a complete listing of accessories available for all machines.
For a free issue of The Blue Press, call our customer service department at: 1-800-223-4570
SUPER 1050 Manual#11011
Super 1050, May 2007 5/21/07 12:00 PM Page 32