Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2007 American Honda Motor Co., Inc. – All Rights Re
AII 35365
REMOTE CONTROL ENGINE STARTERserved. AII 35365 (0708
2008 ACCORD 4-DOOR
) 0
Issue Date
AUG 2007
PARTS LIST
Remote Engine Starter Unit KitP/N 08E91-E22-100A
Transmitter
Control unit
Antenna
Key ring
Protective tape
Caution label
Fuse labels
Accessory User’s Information Manual
Quick start guide
Remote Control Engine Starter Attachment KitP/N 08E92-TA0-100
Engine starter harness
Control unit bracket
Template
3 Relays
Flange nut
U
1 of 248E92-TA0-1000-91
Ground bolt
20 Wire ties
2 Long wire ties
8 Urethane tapes
A-Pillar clip
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriver
Phillips screwdriver
Small flat-tip screwdriver
Ratchet
10 mm Socket
Combination wrench
Isopropyl alcohol
Shop towel
Tape measure
Clip remover
Scissors
Small rubber mallet
Honda Diagnostic System (HDS)
Masking tape
Needle nose pliers
2 of 24 AII 35365
Illustration of the Engine Starter Installed on the Vehicle
INSTALLATION
NOTE:
• This antenna should only be installed if the ambient air temperature 15°C (60°F) or above.
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
711102AY
40AFUSE CASE
ENGINE STARTER HARNESS
ANTENNA
3A FUSE CASE
40AFUSE CASE
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
3. Remove the driver’s dashboard lower cover (eight clips, two hooks, and disconnect the vehicle connector).
4. V6 Model only: Remove the driver’s dashboard under cover (three clips and one pin).
6D1803AY
8 CLIPS
DRIVER’S DASHBOARD LOWER COVER
2 HOOKS
VEHICLE CONNECTOR
.
6D18040Y
3 CLIPS
DRIVER’S DASHBOARD UNDER COVER
PIN
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
5. Remove the cover from the trunk lid/fuel fill door opener (six retaining tabs), and remove one self- tapping screw. Make sure the trunk lid/fuel fill door opener is unlocked.
6. Raise the front portion of the left front door sill trim (four clips and retaining tab).
711104BY
SELF TAPPING SCREW
Unlock.KEY
TRUNK LID/FUEL FILL DOOR OPENER
6 RETAINING TABS
COVER
FRONT
760501AE
FRONT
RETAINING TAB
LEFT FRONT DOOR SILL TRIM
4 CLIPS
(0708) 3 of 24
7. Pull away the weatherstrip, and remove the left kick panel (two clips).
8. Pull away the weatherstrip and remove the left dashboard side cover (seven retaining tabs and three hooks).
7111080Y
2 CLIPSWEATHERSTRIP
LEFT KICK PANEL
6D1805BY
LEFT DASHBOARD SIDE COVER
7 RETAINING TABS
3 HOOKS
WEATHERSTRIP
4 of 24 AII 35365
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.9. Lower the tilt lever and pull the steering wheel out.
10. Remove the upper steering column cover:
• Insert a flat-tip screwdriver along the column guide inside the lower cover, and gently pry out on the retaining tab of the upper column cover.
• Push the lower cover in at the areas shown to release the two retaining tabs, and pull up on the upper cover to release the two hooks.
11. Remove the lower steering column cover (three screws). The upper screws are self-tapping screws.
7215010K
LOWER STEERING COLUMN COVER
UPPER STEERING COLUMN COVER
RETAINING TAB
TILT LEVER
COLUMN GUIDE
FLAT-TIP SCREWDRIVER
2 HOOKS
2 RETAINING TABS
Push.
7111090Y
LOWER STEERING COLUMN COVER
SELF-TAPPING SCREWSSCREW
12. Remove the roof console:
• Using a small flat-tip screwdriver wrapped with a shop towel, pry out and remove the left and right lens (four retaining tabs each).
• Open the sunglass holder, and remove the four screws.
• Disconnect the vehicle connectors to remove the roof console.
7215010Y
ROOF CONSOLE
LEFT LENS
4 RETAINING TABS
RIGHT LENS
4 RETAINING TABSSHOP
TOWEL
FLAT-TIP SCREWDRIVER
7215020Y
4 SCREWS
ROOF CONSOLE
SUNGLASS HOLDEROpen.
VEHICLE CONNECTOR
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
13. Turn the sunvisor holder 90°, and remove the two sunvisor holders.
14. Remove the driver’s sunvisor.
• Turn the left sunvisor toward the driver’s seat.
• Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
• While holding the retaining tab, push up on the left sunvisor and rotate toward the door to remove.
NOTE: If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat the steps above.
6D1806BY
SUNVISOR HOLDER
Turn.
SUNVISOR HOLDERS
761804AB
LEFT SUNVISOR(Turn rearward.)
Push upward.
FLAT-TIPSCREWDRIVER
HOLDER
Push and hold tab.
Rotate towards the door.
(0708) 5 of 24
15. Pull away the weatherstrip from the left front A-pillar trim.
16. Using a small rubber mallet and a shop towel, gently tap the left front A-pillar trim at the position shown to release the clip.
17. Pull away the weatherstrip from the left front A-pillar trim. Remove the left front A-pillar trim (two clips).
711110BY
CLIP
FRONT A-PILLAR TRIM
FRONT PILLAR
PIN
STRIKE POINT
SHOP TOWEL
RUBBER MALLET
LEFT FRONT A-PILLAR TRIM
CLIP
WEATHER-STRIP
Strike perpendicular to the vehicle.
TRIANGLE MARK
6D18070Y
2 CLIPS
WEATHERSTRIP
LEFT FRONT A-PILLAR TRIM
6 of 24 AII 35365
18. Remove and discard the clip from the left front A- pillar trim, and install a new A-pillar clip (supplied) on the left front A-pillar trim.
19. If equipped, remove the HandsFreeLink control unit (two bolts and disconnect the vehicle 28-pin connector).
6D18080Y
CLIP (Discard.)
LEFT FRONT A-PILLAR TRIM
NEW A-PILLAR CLIP
732903BY
BOLT
VEHICLE 28-PIN CONNECTOR
HANDS-FREELINK CONTROL UNIT
BOLT
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
Setting the Control Unit
20. Using a small flat-tip screwdriver, adjust the switches on the (accessory) control unit to the locations shown. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Remove the adhesive backing, and attach the protective tape to the control unit.
NOTE:
• If the switch setting is not correct the remote engine starter will not operate correctly.
• If adjusting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
SW:1 RR Junction unit
SW:2 Trunk or Tailgate
SW:3 Smart Entry
SW:4 Horn or Buzzer Answerback
SW:5 Trunk Main SW
SW:6 Reserve
7111031Y
CONTROL UNIT
SWITCH
PROTECTIVE TAPE ADHESIVE
BACKING
Clean with isopropyl alcohol.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
Routing the Engine Starter Harness
21. Attach the two 40A fuse labels to the engine starter fuse block.
22. Attach the 3A fuse label to the engine starter relay block.
23. Install the three relays to the engine starter relay blocks.
732821BY
ENGINE STARTER HARNESS
FUSE BLOCK
3A FUSE LABEL
40A FUSE LABELS
6D1802BY
ENGINE STARTER HARNESS
RELAY BLOCK
3 4-PIN RELAYS
(0708) 7 of 24
24. Remove the vehicle bolt and remove the TPMS control unit from the vehicle bracket.
25. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness over the brake pedal bracket towards the center of the vehicle.
6D18091Y
VEHICLE BRACKET
VEHICLE BOLT
TPMS CONTROL UNIT
STEERING SHAFT
6D1810AY
BRAKE PEDAL BRACKET
ENGINE STARTER HARNESS
12-PIN/8-PIN/5-PIN CONNECTOR
STEERING SHAFT
VEHICLE BRACKET
8 of 24 AII 35365
26. Route the 12-pin, 8-pin, and 5-pin connector end of the engine starter harness to the ignition switch.
27. Disconnect the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch.
NOTE: Check that the engine starter harness 5-pin connector is connected to the vehicle connector and locked securely. A loose connector can cause engine to stall.
6D1812DY
12-PIN/8-PIN/5-PIN CONNECTOR
IGNITION SWITCH
ENGINE STARTER HARNESS
5-PIN CONNECTOR
Unlock connector Lock connector
Push.
VEHICLE 5-PIN CONNECTOR
Push.Pull.12
3 1
2
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
28. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown.
29. Disconnect the turn signal switch 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch.
6D1813AY
URETHANE TAPE
VEHICLE 5-PIN CONNECTOR
VEHICLE 5-PIN CONNECTOR
VEHICLE BRACKET Push.
Push.
Lock connector
1
2
6D18141Y
8-PIN CONNECTORS
BODY SWITCH
12-PIN CONNECTORSTURN SIGNAL SWITCH 12-PINCONNECTOR
ENGINE STARTER HARNESS
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
30. Disconnect the wiper switch 8-pin connector and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
31. Secure the engine starter harness to the vehicle harness using two wire ties. Do not secure it to the SRS harness.
6D18151Y
BODY SWITCH
2 8-PIN CONNECTORS
WIPER SWITCH 8-PIN CONNECTOR
ENGINE STARTER HARNESS
6D1816BY
VEHICLE HARNESS ENGINE
STARTER HARNESS
WIRE TIES
(0708) 9 of 24
32. Secure the engine starter harness to the vehicle harness with two wire ties in the areas shown.
33. Disconnect the vehicle 20-pin connector from the TPMS control unit (removed in step 24), and plug it into the engine starter harness 20-pin connector. Plug the remaining engine starter harness 20-pin connector into the TPMS control unit.
6D1817BY
VEHICLE HARNESS
2 VEHICLE CLIPS
ENGINE STARTER HARNESS
2 WIRE TIES
WIRE TIE VEHICLE HARNESS ENGINE
STARTER HARNESS
Inside.
6D1818AY
VEHICLE 20-PIN CONNECTOR
20-PIN CONNECTOR
TPMS CONTROL UNIT
VEHICLE 20-PIN CONNECTOR
20-PIN CONNECTOR
ENGINE STARTER HARNESS
10 of 24 AII 35365
34. Align the green tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness with one wire tie.
35. Near the connector, secure the engine starter harness to the vehicle harness with one wire tie.
36. Secure the engine starter harness to the vehicle harness with two long wire ties at the locations shown.
6D1811AY
VEHICLE HARNESS
ENGINE STARTER HARNESS
WIRE TIE
VEHICLE CLIP
GREEN TAPE
6D1819EY ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIE
VEHICLE HARNESS
LONG WIRE TIES
CONNECTOR
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
37. Reinstall the TPMS control unit to the vehicle bracket using the vehicle bolt removed in step 24.
38. Route the engine starter harness along the vehicle harness to the front of the fuse box.
39. Loosely attach the engine starter harness to the vehicle harness with one wire tie.
721503AY
VEHICLE BRACKET
VEHICLE UNIT
TPMS CONTROL BOLTRemoved in step 24.
6D1820AY
WIRE TIE (Loosely attach.)FUSE BOX
ENGINE STARTER HARNESS
VEHICLE HARNESS
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
40. Disconnect the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one urethane tape around the vehicle 5-pin connector.
NOTE: Check that the engine starter harness 5-pin connector is connected to the vehicle connector and locked securely. A loose connector can cause engine to stall.
6D1823DY
FUSE BOX
VEHICLE 5-PIN CONNECTOR
5-PIN CONNECTOR
Unlock connector
VEHICLE 5-PIN CONNECTOR
Push.Pull.
Push.
ENGINE STARTER HARNESS
URETHANE TAPE
Lock connector
Push.
Lock connector
Push.
12
31
2
1
2
(0708) 11 of 24
41. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.
NOTE: If the 12-pin connector is already being used, unplug the 12-pin connector from the fuse box, and plug the engine starter harness 12-pin into the fuse box. Remove and discard the dummy connector from the engine starter harness and plug the other accessory 12-pin connector into the engine starter harness.
6D1821BY
FUSE BOX 12-PIN CONNECTOR FUSE BOX
12-PIN CONNECTOR ENGINE STARTER HARNESS
6D1822BY
FUSE BOX 12-PIN CONNECTOR
12-PIN CONNECTOR
12-PIN CONNECTOR
DUMMY CONNECTOR
FUSE BOX
OTHER ACCESSORY CONNECTOR
ENGINE STARTER HARNESS
12 of 24 AII 35365
42. Loosely attach the engine starter harness to the vehicle harness with one wire tie.
43. Disconnect the vehicle 20-pin connector from the fuse box, and plug it into the engine starter harness 20-pin connector. Plug the remaining engine starter harness into the fuse box 20-pin connector.
6D1824AY
VEHICLE HARNESS
ENGINE STARTER HARNESS
WIRE TIE (Attach loosely.)
6D1825AY
FUSE BOX
FUSE BOX20-PIN CONNECTOR
ENGINE STARTER HARNESS 20-PIN CONNECTOR
ENGINE STARTER HARNESS
VEHICLE20-PIN CONNECTOR
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
44. Attach the clip from the engine starter harness connector to the clip on the vehicle connector.
45. Remove and discard the upper hood opener bolt, and install the ground bolt supplied with the ground terminal attached.
6D18260Y
CLIP
HOOD OPENER
VEHICLE CONNECTOR
ENGINE STARTER HARNESS
6D18270Y
VEHICLE BOLT (Discard.)
HOOD OPENER
VEHICLE PANEL
GROUND TERMINAL
GROUND BOLT
ENGINE STARTER HARNESS
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
46. Secure the engine starter harness to the vehicle harness with one wire tie.
47. Loosely attach the engine starter harness to the vehicle harness with two wire ties.
6D18280Y
WIRE TIE
ENGINE STARTER HARNESS
VEHICLE HARNESS
6D18290Y
VEHICLE HARNESS
ENGINE STARTER HARNESS
WIRE TIES (Attach loosely.)
VEHICLE HARNESS
(0708) 13 of 24
Antenna Installation
48. Using scissors, separate the templates.
49. Determine the appropriate template for the vehicle you are working on. Using scissors, cut out the appropriate template.
Without Shaded Glass
751701BY
Cut out.
TEMPLATE
SCISSORS
721505DY
TEMPLATECut out.
14 of 24 AII 35365
With shaded glass, without Day/Night Mirror
With Automatic Day/Night Mirror
721507DY
TEMPLATE
Cut out.
721506DY
TEMPLATECut out.
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
50. Using two pairs of needle nose pliers, bend the antenna plate according to the dimensions shown.
721509BY
ANTENNA
PLATE
10 mm
10 mm
SCALE
NEEDLE NOSE PLIER
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
51. Starting near the antenna end of the cable, wrap three foam cushions around the antenna cable at the measurements shown.
52. Using scissors, cut one foam cushion in half. Wrap the two halves of the foam cushion around the antenna cable at the measurements shown.
7111110Y
390 mm
20 mm
20 mm620 mm
ANTENNA CABLE
URETHANE TAPE
Cut.
ANTENNA CABLE
URETHANE TAPE USE 1/2 URETHANE
(0708) 15 of 24
53. Attach the template to the front window.
Without Shaded Glass
With shaded glass, without Day/Night Mirror
6D1838BY
TEMPLATE
BLACK CERAMIC
FRONT WINDOW
TAPE
CENTER
BLACK CERAMIC OF MIRROR BASE
6D1837BY
TEMPLATE
CENTER
BLACK CERAMIC
FRONT WINDOW
TAPE
BLACK CERAMIC OF MIRROR BASE
16 of 24 AII 35365
With Automatic Day/Night Mirror
6D1839CY
TEMPLATE
CENTER FRONT WINDOW
TAPE
BLACK CERAMIC
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
54. Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach.
55. Remove the adhesive backing from the antenna. Insert the antenna plate over the roof lining, and attach the antenna to the front window aligning it with the template.
56. Remove the template.
57. Gently pull down the headliner, and tuck the antenna cable under it.
721510AY
TEMPLATE
ROOF LINING
ANTENNA
PLATE
ADHESIVE BACKING
6D18400Y
VEHICLE HARNESS
HEADLINER
ANTENNA CABLE
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
58. Using scissors, cut one foam cushion tape in half. Route the antenna cable towards the driver’s side of the vehicle, and secure the antenna cable to the roof panel with the two halves of foam cushion tape.
59. Pull away the weatherstrip, and route the antenna cable down and under the dashboard through the front pillar opening.
6D18420Y
ANTENNA CABLE
VEHICLE PANEL
Cut.
URETHANE TAPE
VEHICLE HARNESS
721511AY
ANTENNA CABLE
FRONT PILLAR TRIM OPENING
(0708) 17 of 24
60. Secure the antenna cable to the vehicle harness with four wire ties.
61. Secure the vehicle 5-pin connector disconnected in step 40 to the vehicle harness with one wire tie.
62. Secure the antenna cable to the vehicle harness with two wire ties.
6D18430Y
ANTENNA CABLE
4 WIRE TIESVEHICLE CLIP
VEHICLE HARNESS
6D1844AY
WIRE TIES
ANTENNA CABLEVEHICLE
5-PIN CONNECTOR
WIRE TIE
VEHICLE HARNESS
18 of 24 AII 35365
63. Route the antenna cable along the engine starter harness.
64. Secure the antenna cable to the engine starter harness with the four wire ties you loosely attached.
Installing the Control Unit
65. Install the control unit bracket to the control unit.
6D1845BY
ANTENNA CABLE
ENGINE STARTER HARNESS
WIRE TIE (Loosely attached.)
VEHICLE HARNESS
WIRE TIE(Loosely attached.)
WIRE TIE (Loosely attached.)
WIRE TIE (Loosely attached.)
6D18461Y
CONTROL UNIT BRACKET
CONTROL UNIT
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
66. Plug the engine starter harness 28-pin connector into the control unit.
67. Install the clip from the engine starter harness on the control unit bracket.
68. Plug the antenna terminal into the control unit.
6D1847BY
CONTROL UNIT BRACKET
CONTROL UNIT
CLIP
28-PIN CONNECTOR
ENGINE STARTER HARNESS
6D18480Y
ANTENNA TERMINAL
CONTROL UNIT
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
69. Secure the control unit to the vehicle frame using the flange nut.
70. Wrap one urethane tape around the vehicle connector.
6D1849AY
VEHICLE FRAME
FLANGE NUT
CONTROL UNIT
732901CY
VEHICLE CONNECTOR
URETHANE TAPE
(0708) 19 of 24
71. Attach the engine starter relay block clip to the vehicle frame.
72. Bundle up the excess antenna cable and secure it to the engine starter harness and the vehicle harness with the loosely installed wire tie.
73. Secure the antenna cable to the engine starter harness with two additional wire ties.
6D18601Y
ENGINE STARTER RELAY BLOCK
ENGINE STARTER HARNESS RELAY BLOCK CLIP
VEHICLE FRAME
6D18620Y
WIRE TIE (Loosely secured.)
Bundle up the antenna cable.
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIES
20 of 24 AII 35365
74. Under the hood, locate the area where the caution label will attach. Using isopropyl on a shop towel, clean the hood where the caution label will attach.
75. Attach the caution label to the hood in the area shown.
76. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the airbag with the clip during reinstallation of the front pillar trim. Do not push excessively on the front pillar trim.
77. Reconnect the negative cable to the battery.
78. Enter the customer’s radio anti-theft code, and reset the radio station presets.
79. Reset the clock on models without navigation.
80. Do the REMOTE ENGINE STARTER REGISTRATION (page 21) and FUNCTION CHECK (page 24).
732902AY
HOOD
CAUTION LABEL
ADHESIVE BACKING
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
REMOTE ENGINE STARTER REGISTRATION
1. Acquire the PCM code from the Interactive Network.
2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position.
3. Start the HDS, and click on the car icon.
4. Input the VIN and other required information into the HDS, then click the check on button.
752501AS
CAR ICON
752502AS
CHECK BUTTONInput the VIN and other required information.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365
5. Select Honda Systems, then click on the check button.
6. Select R/C ENG STARTER and click on the check button.
752503AS
CHECK BUTTONSelect “Honda Systems.”
752504AS
CHECK BUTTONSelect “R/C ENG STARTER.”
(0708) 21 of 24
7. A REMARKS message will display. Click on the check button.
8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click on the check button.
752505AS
CHECK BUTTON
“REMARKS” message
752506AS
CHECK BUTTONSelect “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”
22 of 24 AII 35365
9. The following message will display: Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA). Click on the check button.
10. Input the PCM code, then click on the check button.NOTE: To ensure security, the PCM code (password) is changed every day, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.
752507AS
CHECK BUTTON
“Obtain PCM-code” message
752509AS
CHECK BUTTON
Input the PCM code.
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.
11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button.
12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button.
13. Perform the function test on page 24, then disconnect the HDS.
752510AS
CHECK BUTTON
“The registration of the Remote Con-trol Engine Starter Unit has been com-pleted”
752511AS
CHECK BUTTON
“Check that the engine can be started by the Transmitter”
© 2007 American Honda Motor Co., Inc. – All Rights Reserved. AII 35365 (0708) 23 of 24
FUNCTION CHECK
Operating Conditions
• The hood is closed.
• The shift lever is in park.
• The key is not in the ignition switch.
• All doors and tailgate are closed and locked.
Inspection
1. Within 1 second, press the command button and then the start button on the transmitter.The engine should start if all operating conditions are met.
Does the engine start?
2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop.
Does the engine stop?
3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
Yes - Operation is normal.
No:• Make sure all operating conditions are met.• Check the engine starter harness connections.• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
Yes - Operation is normal.
No - Check the engine starter harness connections.
24 of 24 AII 35365 (0708)
732904AY
DISPLAY
STOP BUTTON
COMMAND BUTTON
START BUTTON
TRANSMITTER
NOTE:
• Each test must be completed within 30 seconds after engine starts.
• After each test the ignition switch must be cycled, or the driver’s door must be opened and closed.
- Move the shift lever out of the P position.
- Unlock or open the doors or the trunk lid.
- Open the hood.
- Insert the key in the ignition switch.
- Press the brake pedal.
Does the engine stop after each of these tests?
Yes - Operation is normal.
4. Check that the power windows or the moonroof does not function when the engine is started with the transmitter.
5. Press the command button on the transmitter twice and check the vehicle condition on the display.
6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 ft. to 490 ft.) away and when the vehicle is in direct sight.
No - Check the engine starter harness connections.
© 2007 American Honda Motor Co., Inc. – All Rights Reserved.