HUMAX (ONT)
Installation
1Strictly Confidential
LED Status indicator
LED Description
POWEROff Device is off/No have electric current
Green LED on
Normal status
CONNECTION
Off OLT does not connect to HUMAX
Green LED on
The connection between OLT and HUMAXis registered
Green LED blink
The connection between OLT and HUMAXis not registered
ALARMOff Normal status
Red LED on Cable has some issue
ETH
OffLAN does not connect / LAN has some issue
Green LED on
CPE and HUMAX do not not sync data
Green LED blink
CPE and HUMAX is syncing data
Front
Strictly Confidential
On/OffFiber cable wire LAN Port
System Connection
Description
LAN PortConnect LAN with HUMAX and WAN Port(Blue Port) of CPE
On/OFFOn (I) / Off (0)
DCPWR Port
DC 12 Volt with HUMAX
Fiber Port Plug fiber cable HUMAX
BackPort Information
3Strictly Confidential
Overview of HUMAX Connection
Strictly Confidential 4
Fiber Cable
PC Staff
192.168.1.254
Humax ONT(SFU)
192.168.1.1
VDSL CPE
WAN port (Blue)
LAN Port1(Yellow)
DHCP
Electric Cable
Note: The system connection in this page has to set before start an activation
OnBlinkOff
LED at Power/Internet/WAN/LAN1/WLAN on and hold
Activation
Strictly Confidential 5
Click HP11X.exe and press Enter
① Connect : Connection button to login with IP that showed on ONT IP Address (192.168.1.254)
② Disconnect : Disconnect with HUMAX③ Get Password : See current password (Activation
number) that was set to HUMAX④ Set Password : Set new password
This button can use after enter a correct activation number in 8 already
⑤ Retrieve Optical RX/TX power : Click on this button to measure the optical power that will show in 9
⑥ Exit : Exit an application⑦ ONT IP address : IP address of HUMAX⑧ ONT password : Enter Activation number ⑨ Rx Power / Tx Power
1 23 4
5
7
6
89
Application Details
6Strictly Confidential
Strictly Confidential 7
- After start a program, the window will be displayed. Click Connect
- Program will display a message
“Succeeded to connect the device” if a connection is successfully
Step 1
OnBlink
Off
1. Click Connect
Strictly Confidential 8
- In another way, the message“Couldn’t connect to the device”
will be displayed if the device cannot connect
Step 1 (Continue)
OnBlink
Off
1. Click Connect
Strictly Confidential
- Click on ”Retrieve Optical Rx/TxPower” to measure RX/TX Power
- Program will send message “Succeeded to retrieve Rx/Tx”
- Record Rx/Tx
Step 2
2. Click
OnBlink
Off
9
Strictly Confidential
- Click ”Get Password” an old password of ONT will display in ONT Password
- Change ONT Password by enter Activation number of customer
- Press ”Set Password” then the background of a message “Succeeded to connect the device” will change to green
Step 3
2. Click
3.Enter Customer’s activation number 4. Click
OnBlink
Off 10
Strictly Confidential
Step 4
OnOn
OffOn/Blink
Successful
Turn off HUMAX then turn on again- If activation number is correct the
LED status will display like a figure below
- If activation number is wrong, Check an activation number then do a step 3 again
11
Registration
12Strictly Confidential
Step 1
- Launch browser, it will redirect to registration page automatically
- If the page is not showed, go to network.ais.co.th/?cond=registration&accesstype=VDSL
13Strictly Confidential
Step 2
- Enter last 4-digits of activation number then press Submit - Enter Keyword of company then press Submit
14Strictly Confidential
15
Step 3
- The page will display as figure below, that means a registration is successful
Strictly Confidential
The steps to retrieve Rx/Tx after installation
16Strictly Confidential
Strictly Confidential 17
- If HP11X.exe was closed when the installation finished, it will cannot connect to HUMAX when start HP11X.exe again
- A program will show message “Couldn’t connect to the device”
Step 1
1. Click
Strictly Confidential 18
Step 2
Fiber cable
PC Staff
192.168.1.254
Humax ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1(yellow)
DHCP
Electric cable
Fiber cable
PCStaff
192.168.1.254
Humax ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1(yellow)
DHCP
Electric Cable
- Change LAN connection of VDSL CPE from WAN port (blue) to LAN Port 2 (yellow)
WAN Port (blue)LAN Port2(yellow)
Strictly Confidential 19
- Click Connect- Click “Retrieve Optical Rx/Tx Power”- Record
Step 3
1. Click
2. Click
Strictly Confidential 20
Step 4
Fiber cable
PC Staff
192.168.1.254
Humax ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1(yellow)
DHCP
Electric cable
Fiber cable
PC Staff
192.168.1.254
Humax ONT(SFU)
192.168.1.1
VDSL CPE
LAN Port1(yellow)
DHCP
Electric cable
- Change LAN connection back
LAN Port2(yellow) WAN Port (blue)
Steps of LED indicator ofNormal HUMAX
Power On
Strictly Confidential 22
ETH On
Strictly Confidential 23
Connection On
Strictly Confidential 24
Appendix
Appendix 1
Strictly Confidential 26
- Connect Electric and Fiber cables to HUMAX
- Press On button, Green LED at POWER will on and hold
On(I)/Off(O)Fiber cableElectric cable
Strictly Confidential 27
Appendix 1 (Continue)
- For a moment, LED at connectionwill blink
- If LED at connection still off and Red LED at Alarm is on and
holding, that means the
connection of fiber cable isabnormal
Strictly Confidential 28
- Connect LAN with HUMAX then green LED at ETH will blink
Appendix 2
Strictly Confidential 29
- If it has some issue with fiber cable,
red LED at Alarm will on and hold
Appendix 2 (Continue)