Hambleside Danelaw
GRP Flashings, Roof and CavityVentilation Products
www.hambleside-danelaw.co.uk
Edition
1
Ventilation to negate the effects of condensation in roofs is essential to comply with Building Regulations, Building Standards and British Standards. Ventilation openings should be provided on the longer sides of rectangular roofs and designed to prevent the ingress of rain, snow, birds and large insects. Minimum mesh/grille sizes should not be smaller than 4mm to avoid excessive airflow resistance. Particular attention should be paid to potential restrictions at changes in roof slope or changes in constructional details and at junctions with walls. The Hambleside Danelaw range of ventilation products is manufactured to enable compliance with all current technical requirements and standards.
BUILDING REGULATIONS – THE REQUIREMENTSApproved Document C2 (2004 Edition) requires that roofs be designed and constructed so that their structural and thermal performance are not adversely affected by interstitial condensation.
This requirement will be met if the roof is designed and constructed in accordance with Clause 8.4 of BS 5250:2002 ‘Code of practice for control of condensation in buildings’ and BS ENISO13788:2001 ‘Hygrothermal performance of building components and building elements. Internal surface temperature to avoid critical surface humidity and interstitial condensation. Calculation methods.’ Further guidance is given in BRE Report BR262 ‘Thermal insulation: avoiding risks’, 2002 edition.
To avoid excessive moisture transfer into roof voids, gaps and penetrations for pipes and electrical wiring should be filled and sealed, particularly in areas of high humidity such as kitchens and bathrooms and an effective draught seal should be provided to loft hatches to reduce the inflow of warm air and moisture. Vapour control layers can reduce the amount of vapour entering roof voids but cannot be relied on as an alternative to ventilation. A complete barrier to moisture is needed for this.
Scottish Building Standards Handbook 3.15 requires that dwellings shall be so constructed as to protect the building and its users, so far as may be reasonably practicable, from harmful effects caused by surface and interstitial condensation. Both these requirements are deemed to be satisfied by following the guidance given in BS 5250.
BS 5534:2003 ‘Code of practice for slating and tiling (including shingles)’ recommends that roof ventilation be provided in accordance with BS 5250.
COLD ROOFS WITH A PITCH OF 15° OR MOREPitched roof spaces should have ventilation openings at eaves level (Fig. A) on opposite sides of the structure at least equal to an opening of 10mm wide and running the full length of the eaves to promote cross ventilation. For roof pitches above 35° or spans in excess of 10m, additional high level ventilation at or close to the ridge equivalent to a continuous opening of 5mm should be provided.
A pitched roof that has a single slope or abuts a wall (Fig. F) should have ventilation at high level equal to a continuous opening of 5mm wide in conjunction with an opening of at least 10mm wide at the eaves.
High level ventilation should never be used on its own as the wind suction effect created will increase water vapour transfer into the roof void.
Pitched roofs where part or all the insulation follows the pitch of the roof (Fig. C) should have ventilation openings on opposite sides of the structure at least equal to a continuous opening of 25mm wide. In addition, such structures require ventilation at or close to the ridge equivalent to a continuous opening of at least 5mm. The void between the underside of the roof covering and the insulation should have a free air space of at least 50mm. In this application, a vapour control layer should also be provided on the warm side of the insulation.
COLD ROOFS WITH A PITCH OF LESS THAN 15°Roof spaces in low pitched and flat roofs should have ventilation openings at eaves level (Figs. B, D & E) on opposite sides of the structure at least equal to an opening of 25mm wide to promote cross ventilation. Roof voids should have a free air space of at least 50mm between the roof deck or underside of the roof covering and the insulation.
Mono pitched roofs should be provided with ventilation of at least the equivalent of a 25mm continuous opening at eaves and 5mm at the ridge.
WARM ROOFSCondensation should be controlled by ventilation beneath the underlay and above the insulation by the provision of a 25mm wide continuous ventilation opening or equivalent at eaves or low level and a 5mm continuous ventilation opening or equivalent at the ridge or high level. The space between the underlay and the insulation should be at least 50mm deep with a minimum of 25mm at the centre of the underlay drape. A well sealed ceiling and separate vapour control layer should be used on the warm side of the insulation.
VAPOUR PERMEABLE UNDERLAySBS 5250:2002 provides recommendations and alternative approaches when using vapour permeable or ‘Low Resistance’ (type LR) underlays that when followed, can achieve compliance with Building Regulations. Caution should be taken when proposing to use VPU’s and reduce ventilation levels on re-roof & refurbishment projects.
Horizontal Insulation:With slated or tiled roofs containing horizontal insulation over a horizontal ceiling, the use of an LR underlay with unsealed laps can allow for a reduction in the area of roof ventilation openings providing that the roof covering can be determined as sufficiently air open in accordance with Annnex L of BS 5534:2003 but with equipment designed to measure low pressure differences down to 2 Pascals. On buildings ‘typical’ of housing, with insulation at ceiling level and with the LR underlay laid above or below counterbattens or onto open jointed sarking boards, the requirement is for low level continuous equivalent ventilation openings that may be reduced from 10mm to 7mm for a ‘normal’ ceiling and 3mm for a well sealed ceiling as defined in BS 9250:2007. For larger roofs of this type, such as supermarkets, schools, hospitals etc., the minimum equivalent opening remains at 10mm for a normal ceiling but may be reduced to 5mm for a well sealed ceiling with an additional continuous 5mm opening at high level.
Where continuous boarding or close jointed sarking boards are used under the slates or tiles, an LR underlay should be treated as a ‘High Resistance’ (type HR) and ventilation should always be provided to the roof space below the underlay. When an existing roof is being recovered, it may be impossible to achieve a ceiling that is as well sealed as in new build therefore caution must be taken and consideration given to providing the equivalent to at least a continuous 7mm opening or the addition of the equivalent to a continuous 5mm opening at high level.
Most proprietary low level ventilation products that provide an area equivalent to a 10mm continuous opening will easily satisfy all of the reduced ventilation requirements. BS 5250:2002 does not cover situations where it is proposed to provide no ventilation in cold roof applications. In such cases, all of the conditions and requirements of independent technical approval certification (e.g. BBA) should be met. Inclined Insulation:Slated or tiled roofs that are air open containing inclined insulation above inclined ceilings may be constructed without ventilation if an LR underlay is used that can either be laid fully supported on the insulation or draped and unsupported. It is essential to provide a well sealed ceiling in accordance with BS 9250:2007 and a separate vapour control layer.
If there is any doubt about the ability to provide and maintain an effectively sealed vapour control layer then ventilation should be provided as if the underlay was impermeable or an HR type in accordance with the section headed ‘Warm Roofs’.
With this type of construction, an effective vapour control layer of high vapour resistance, sealed at the laps and at all roof details, e.g. hips, valleys, ridges, abutments, firewalls and around all penetrations created by services, etc., should be provided. The designer should be sure that the vapour control layers and/or insulation can be installed and maintained air tight for the design life of the building.
FIRE PERFORMANCE OF ROOF VENTILATION PRODUCTSIn general, and for the purposes of Building Regulations requirement B4, small plastic components such as slate and tile ventilators and soil pipe penetrations that occur on the surface of the roof and jointing and ventilation strips that appear at ridges, hips and soffits are regarded as insignificant and are therefore not covered in Approved Document B and can normally be ignored.
SUSPENDED FLOORS AT GROUND LEVELAny suspended floor next to the ground will meet the requirements of Building Regulations Approved Document C, Scottish Building Standards Handbook 3.4 and BS 5250:2002 provided that:a) the ground is covered so as to resist moisture and prevent plant growth
and;b) there is a ventilated air space between the ground covering and the
floor construction of at least 150mm and;c) there are damp-proof courses between the floor construction and any
material that can carry moisture from the ground.
Two opposing external walls should have ventilation openings placed so that the ventilating air will have a free path between opposite sides and to all parts. The openings should be large enough to give an actual opening of at least equivalent to 1500mm² for each metre run of wall or 500mm² per m² of floor area whichever gives the greater opening area, this opening area also being provided in internal sleeper walls or similar obstructions to maintain the underfloor ventilation. Any pipes needed to carry this ventilating air should have a diameter of at least 100mm.
Ventilation Ventilation GRP FlaSHinGS
GeneRal
the illustrations below reflect the basic ventilation requirements which would normally be applicable. For additional information please refer to the current Building Regulations and appropriate British Standards.Dimensions in millimetres.
(A)
+15°
+15°
–15°
(B)
(D)
(E)
(C)
(F)
(G)
Contents and Product index Regulations & Requirements on Ventilation
accreditation
Hambleside Danelaw GRP flashing products carry BBA Certification. The range of valley troughs hold unique BBA multi-product certification.
Hambleside Danelaw is BS EN ISO 14001:2004 Environmental Management Systems - Registered.
Where appropriate products have been independently tested for suitability, purpose and performance by Birmingham City Laboratories.
The Hambleside Danelaw Group are CPD and RIBA CPD Certified providers.
Memberships
Hambleside Danelaw is a member of the RIBA NBS Plus electronic library service.
Hambleside Danelaw is an associate member of the Builders Merchant Federation.
Hambleside Danelaw are associate manufacturing members of the National Federation of Roofing Contractors and also participate in the co-partnership guarantee scheme.
HaMBleSiDe Danelaw anD tHe enViRonMent
Brief details on our environmental policy are shown on the back cover of this brochure. Copies of our Environment brochure and our Corporate Social Responsibility statement are available on our web site or through our Daventry office.
This brochure is designed to provide an overall guide to the Hambleside Danelaw Roofing and Ventilation range of products. Further technical information is available by contacting our Daventry Sales Office on 01327 701910.
(Less than 15°, 25mm required at eaves)
RooF Ventilation
UnDeRFlooR Ventilation
Roof Space
2 Technical Notes on Ventilation
3 Product Applications – Ventilation
5 Soffit Ventilators Cicular Soffit Ventilator Corbel Ventilator
6 Over Fascia Ventilators Airflow Diagrams
7 Universal Panel Ventilators Single and Double Flyscreen Ventilators
8 3 in 1 Ventilator Pack Roll Panel and Universal Refurbishment Tray Ventilators
9 Slate Roof Ventilators Universal and Flush Fitting Slate Roof Ventilators Soil Pipe Adapter Kits
10 Tile Roof Ventilators Plain Tile Roof Ventilator Soil Pipe Adapter Kits
11 Dry Fix Ventilated Ridge System
Cavity and Underfloor
12 Telescopic Underfloor Ventilator Combination Brick Ventilator Airbrick Ventilator Sleeves Ventilator Grilles
13 Square to Round Adapter Universal Weep Ventilator Lintel Stop End Perp Weep and Extension
Ancillary Products
22 Universal Eaves Comb Filler Underlay Support Tray Rigid Underlay Support Tray Moisture Diversion Plate Loft Access Doors
Roof and Wall
14 Dry Fix Valley Trough for Slate Roofs Dry Fix Valley Trough for Tile Roofs
15 StormForce 225 Tile Valley Troughs Slate Valley Troughs Scottish Slate Valley Trough
16 Installation of GRP Valley Troughs
17 Dry Fix Bonding Gutter and Bonding Gutter™
18 Damp Proof Course Continuous Eaves Course Universal Abutment Cover Flashing
19 Continuous Soakers for Slates and Tiles
20 Dry Soakers for Slates and Tiles
21 Dry Verges Scotverge
BCl
EMS 500154FM 23063
OHS 532271
2 3
tile anD Slate RooF VentilatoRSeaVeS Panel VentilatoRS
CaVitY anD UnDeRFlooR VentilatoRS
HD 9600B Factory Fitted VERMIN SCREEN
HD 9300 COMBINATION AIR BRICK
HD 9300G GAS VENT GRILLE
HD 9400/1/2/3 INTERNAL VENT GRILLE
HD 96200 SQUARE TO ROUND ADAPTER
HD 9350/1AIRBRICK VENTILATOR SLEEVES
HD 9350/2AIRBRICK VENTILATOR SLEEVES
HD 9350/3AIRBRICK VENTILATOR SLEEVES
HD 12000U
HD 12000M
HD 8000
HD 8250
HD 4000, HD 4500 and HD 6000
HD 5000 UNIVERSAL ROLL PANEL
HD URT UNIVERSAL REFURBISHMENT TRAY
HD 4050, HD 4550 and HD 6050
HD 4025, HD 4525 and HD 6025
DFR3 DRY FIX RIDGE/VENTILATION SYSTEM
PRoDUCt SeleCtion eaVeS anD SoFFit VentilatoRS
HD TV15/3 HD TV15/4
HD TV10/8
HD TV15/7
HD TV10/5
HD TV10/6 HD SRV10U HD ILSRV10UHD SRV680HD SRV5U
HD TV15/1 HD TV15/2
tVSPa Soil Pipe Adapter for use with HD TV15/1, HD TV15/2, HD TV15/3, HD TV15/4 and HD TV15 /7 tile roof ventilators
HD PCSPa Plain tile soil pipe adapter for HD TV10/5 ventilator – soil ventilation only
HD SPa680 For use with HD SRV680 slate roof ventilators
HD SPaFor use with HD SRV10/U slate roof ventilators
HD FPCFlexi-pipe can be used as an extension to all HDL Soil Pipe Adapter Kits
As a general guide to assist in choosing the correct products from the Hambleside Danelaw range, first identify the type of roof detail from the typical examples to illustrated, then select the combination of products from the range to achieve full cross flow ventilation in accordance with the Building Regulations.
A G
HD 8310 CORBEL VENTILATOR
DRY FiX RiDGe
HD ILSRV10/20 and HD ILSRV10/24
Ventilation
HD 9600CTCavity Tray
HD 9800 LINTEL STOP END
HD 9100 PERP WEEP
HD 9600M Telescopic VentilatorHD 9600CT Cavity TrayHD 9300 Airbrick Ventilator
Horizontal Extension Sleeves:-HD 9660M (Bottom)HD 9660T (Top)
HD 9610/2Vertical Extension Sleeve
Horizontal Extension Sleeves:- HD 9660M (Bottom)HD 9660T (Top)
HD 9200Perp Weep Extension
Product applications
HD RSPa Soil pipe adapter for HD TV 10/6 and HD TV10/8 ventilators
WEEP VENT HD 9500
HD ilSPaFor use with HD ILSRV10/20 & HD ILSRV10/24 slate roof ventilators
Soil Pipe Adapter Code HD ILSPAU compatible for use with HD ILSRV10U slate roof ventilators
B C D E G A F
A F A FHD 8210
A B C D E F G A FHD 7000
A F
A
B
C
D
E
F
G
A B C F G A B C F G
A B C FA F
B C G
4 5
USe: To provide a through-flow of ventilating air over the fascia board in both new build and refurbishment details.aDVantaGeS: Unique two stepped fixing positions to allow for use on roofs above and below 15° of pitch, allowing the through-flows of air at 25,000mm² and 10,000mm² per metre respectively. Reinforced nailing guides ensure accurate fixing to fascia and also for eaves comb filler. Standard flyscreen conforms to regulation
requirements. Rounded front section prevents blocking of airflow from overlapping underlay. Use with Hambleside Danelaw’s range of Panel and Roll Panel ventilators.aiRFlowS:25mm position = 25,000mm² per metre. 10mm position = 10,000mm² per metre.MateRial: Black injection moulded polypropylene.lenGtH: 1m.
USe: To provide a through-flow of ventilating air over the fascia board in both new build and refurbishment details.aDVantaGeS: Reinforced nailing guides ensure accurate fixing to fascia and also for eaves comb filler. Standard flyscreen conforms to regulation requirements. Rounded front section prevents blocking of airflow from overlapping underlay. Use with Hambleside Danelaw’s
range of Panel and Roll Panel ventilators.aiRFlow: 10,000mm² per metre.MateRial: Black injection moulded polypropylene.lenGtH: 1m.
CoRBel VentilatoRHD 8310
SoFFit VentilatoRSHD 8000 & HD 8250
oVeR FaSCia VentilatoRHD 12000M
aiRFlow DiaGRaMS
aiRFlow DiaGRaMS
SoFFit VentilatoRHD 8210
ILLUSTRATED WITH HD 8000 SOFFIT VENT: HD 6000/HD 4500/HD 4000 UNIVERSAL PANELS TO VENTILATE TO 10,000mm² OR 25,000mm² PER METRE
HD 7000 CIRCULAR SOFFIT VENTILATORS FORM AN ATTRACTIVE AND EFFECTIVE SOLUTION
USe: To provide air ventilation at eaves level where a continuous masonry corbel of brick, stone or similar is constructed.BeneFitS: The base at the rear of the ventilator has a dovetail anchoring slot which enables security ties to be positively attached at any position to suit the corbel masonry joints.
aiRFlow: 10,000mm² per metre run.MateRial: PVCU. lenGtH: 2.4 mColoUR: Black.
USe: Permits entry of air into roofspace in projecting soffit situations. When fitted on opposite sides of a rectangular roof structure will satisfy the requirements of the Building Regulations, e.g. front and rear elevations.aDVantaGeS: This ventilator is designed for use with sloping soffit situations, and may be butted up to brickwork when used without a soffit board. Other applications for this ventilator exist, for instance, in no fascia
situations, or at high level on a mono pitch roof. For further information contact our technical services department.FlY SCReen: Recommended 4mm wide slots.aiRFlow: 10,000mm² per metre run.MateRial: PVCU. lenGtH: 2.4 mColoURS: White and Brown.
USe: Permits entry of air into roofspace in projecting soffit situations. When fitted on opposite sides of a rectangular roof structure will satisfy the requirements of the Building Regulations, e.g. front and rear elevations.aDVantaGeS: Lightweight, easy to handle and fix strips. (Strips are punched with fixing slots.) Will support soffit boards between 4mm and 10mm in thickness, up to 300mm wide without additional noggins; provides
well in excess of the minimum required airflow. Ideal for new build applications.FlY SCReen: Recommended 4mm wide slots.aiRFlow: HD 8000 = 10,000mm² per m.Roof pitch: above 15°.HD 8250 = 25,000mm² per m.Roof pitch: below 15°.MateRial: UV stabilised PVC. lenGtH: 2.4 m strips.ColoURS: White and Brown.HD 8000 also in Black.
UniVeRSal oVeR FaSCia VentilatoRHD 12000U
USe: This vent, when introduced into existing unventilated soffit boards in refurbishment projects, will permit entry of air into the roof-space.aDVantaGeS: Easily fitted into pre-drilled 70mm diameter holes. Standard flyscreen conforms to regulation requirements.
aiRFlow:Per vent (mm²) 2,500mm²Vents per metre: 4Fitted at centres: 250mmProvides: 10,000mm² per metre.MateRial: PolypropyleneColoURS: White, Brown, Light Oak and Black.BaSe DiaMeteR: 80mm
CiRCUlaR SoFFit VentilatoRHD 7000
HD 12000U
HD 8250 HD 7000
HD 8210 HD 8000
HD 8250
HD 8210
HD 7000
HD 8000
ILLUSTRATED WITH HD 8210 SOFFIT VENT: HD 6000/HD 4500/ HD 4000 UNIVERSAL PANELS TO VENTILATE TO 10,000mm² OR 25,000mm² PER METRE
Soffit Ventilators
HD 8310
Roof Ventilation Products
over Fascia Ventilators
Roof Ventilation Products
ILLUSTRATED WITH HD 12000U OVER FASCIA VENT: HD 3025VP TO VENTILATE TO 10,000mm² OR 25,000mm² PER METRE
ILLUSTRATED WITH HD 8250 SOFFIT STRIP: HD 5000 UNIVERSAL ROLL PANEL TO VENTILATE TO 25,000mm² OR 10,000mm² PER METRE
25 mmAIRFLOW POSITION
A
10 mmAIRFLOW POSITION
B
51
22
80
22
80
8
26
42
47
15
14 20
36
18
34
6 7
The most cost effective and simple way of providing a complete ventilation and felt or underlay support system giving additional protection to the fascia detail of all roof types.
A unique feature of this system is the new Universal Over Fascia Ventilator with two fixing positions that adapt to 10mm and 25mm airflows.
HD 3025VP contains:
1 x 6 metre Roll Panel (HD 5000)
10 x 600mm Underlay Support Trays (HD 3000)
6 x 1 metre Over Fascia Vent (HD 12000U).
The products within the ‘3 in 1’ pack are available separately.
THE HD 3000VP VENT PACK IS ALSO AVAILABLE WITH A STANDARD FIX 10,000mm² AIRFLOW OVER FASCIA VENTILATOR.
Installation of the HD 3025VP Vent Pack is straightforward. The Over Fascia Ventilator is fitted to the top edge of the fascia board, in either of the two stepped positions, to suit the required level of airflow and the Roll Panel and Underlay Support Tray are then installed.
The Underlay Support Tray is placed on top of the Over Fascia Ventilator and nailed into place through holes provided in the over fascia vent. This will make it much easier to locate alternative nail holes if an Eaves Comb Filler is to be fitted. It is then nailed at the top edge of the tray through the Roll Panel if required and into the rafter. Consecutive trays are lapped by 50mm using the raised locators formed into the tray sides. The Underlay Support Tray forms the drip into the gutter.
aiRFlowS:25mm fixing position = 25,000mm² per metre10mm fixing position = 10,000mm² per metre
UniVeRSal Panel VentilatoRSHD 6000, HD 4500 & HD 4000
SinGle FlYSCReen +15° PitCHHD 6050, HD 4550, HD 4050
DoUBle FlYSCReen –15° PitCHHD 6025, HD 4525, HD 4025
3 in 1 VentilatoR PaCKHD 3025VP
Roll Panel VentilatoRHD 5000
UniVeRSal ReFURBiSHMent tRaY VentilatoRHD URt
USe: In normal situations the insulation is laid up to and over the wall plate to avoid ‘cold bridging’. In some cases this insulation can block the air circulation into the roofspace. The panel ventilator is fitted between the insulation and underlay and over the rafters to ensure a clear air passageway from the soffit into the roof space; use when the roof pitch is either below 15° or above 15°.
aDVantaGeS: Lightweight, easy to handle and fix panels; in three sizes to fit most rafter spacings; formed with ribs to ensure felt cannot drape into the panel and block airflow.
HD 6000, HD 4500, HD 4000
aiRFlow: Per panel Per metreHD 6000 16,000mm² 29,090mm²HD 4500 12,000mm² 30,000mm² HD 4000 9,000mm² 25,714mm²
MateRial: PVC.ColoUR: Black
USe: For open eaves details, protruding flyscreen with recommended 4mm slots; use on roof pitches of 15° or above.
FlYSCReen PanelS: The 6050 range of Panel Ventilatorsis available with a single row of slotted screen protection. These panels, when fitted to every rafter centre will provide the regulation requirement of a continuous 10mm gap at the eaves.
HD 6050, HD 4550, HD 4050 flyscreen panels.
aiRFlow: Per Panel Per MetreHD 6050 6,843mm² 12,441mm²HD 4550 5,132mm² 12,830mm²HD 4050 4,474mm² 12,782mm²
MateRial: PVC.ColoUR: Black.
USe: For open eaves details, protruding flyscreen with recommended 4mm slots; use on roof pitches below 15°.
FlYSCReen PanelS: The 6025 range of Panel Ventilators is available with double rows of slotted screen protection. These panels, when fitted to every rafter centre will provide the regulation requirement of a continuous 25mm gap at the eaves.
HD 6025, HD 4525, HD 4025 flyscreen panels.
aiRFlow: Per Panel Per MetreHD 6025 13,786mm² 25,065mm²HD 4525 10,264mm² 25,660mm²HD 4025 8,948mm² 25,565mm² MateRial: PVC.ColoUR: Black.
USe: Prevents insulation blockage at eaves and allows high levels of cross flow ventilation – eaves to eaves. Use in conjunction with the Hambleside Danelaw range of soffit ventilators to achieve full eaves to eaves airflow.
aDVantaGeS: Universal rafter centre fitting capability. Conforms to 10mm and 25mm requirements.
aiRFlow:25,000mm² per metre
MateRial: PVC.ColoUR: Black.lenGtH: 6 metre rolls.
USe: A rafter tray specifically designed for installation into the eaves of a completed and traditionally constructed tiled or slated roof. Inserted to ensure that insulation blockage of the path of air necessary to ventilate the roof space does not occur.
If no means of introducing air through the soffit or over fascia exists the HD 7000 Circular Soffit can be fitted retrospectively into the soffit board.
BeneFitS: A universal refurbishment tray designed to be used either as a single panel to rafter centres of 450mm or below 450mm by trimming the panel to suit. For rafter centres between 450mm and 600mm the panel can be extended by cutting a second panel in half and connecting the two together.
aiRFlow: 25,000mm² per metre
MateRial: PVC.ColoUR: Black.
eaves Panel Ventilators
Roof Ventilation Products
Available in 3 widths to suit 400 mm, 450 mm and 600 mm rafter centres
Available in 3 widths to suit 400 mm, 450 mm and 600 mm rafter centres
Available in 3 widths to suit 400 mm, 450 mm and 600 mm rafter centres
eaves Panel Ventilators
Roof Ventilation Products
MateRial: Manufactured from high density polypropylene for durability and thermal stability. The vent has a non-reflective surface and is UV stabilised to prevent colour loss and embrittlement through age.ColoURS Standard colour range of Terracotta, Brown, Antique Red, and Grey. Special colours to order.
Vent aRea 2,000mm² actual ventilation area per tile ventilator.USe: Fitted in groups of 5 to achieve regulation 10,000mm² per metre.
8 9
HD SPa680 For use with HD SRV680 slate roof ventilators.USe: Connecting 110mm soil vent pipe outlet to 10,000mm² area ventilator.aDVantaGeS: May be used for mechanical extraction when fitted to HD SRV10U and HD SRV680 vents. Length = 500mm.aiRFlow: Total through ventilation area for both adapters is 8,000mm².adapters only available.
USe: Slate roof ventilator for use with with man-made or natural slates.aDVantaGeS: Long life, simple to install with minimum cutting of slates. UV light and acid rain resistant. Large base for ‘random’ slate roofs with a
facility for trimming to 600 x 300mm. Stable at temperatures of -40°C to +120°C.May be used for soil ventilation and mechanical extraction when fitted with the HD SPA680 soil pipe adapter kit.MateRial: High density polypropylene in Black. Grey to order.aiRFlow: 20,000mm² actual ventilation area.aCtUal BaSe SiZe: 452mm wide x 682mm deep.NOTE: Roofing underlay preparation to be in accordance with HD ILSRV’s.
USe: Universal slate roof ventilator for use with man-made or natural slates.aDVantaGeS: Long life, simple to install with minimum cutting of slates. UV light and acid rain resistant. Colour through material – stable at temperatures of -40°C to +120°C.
MateRial anD SiZe: High density polypropylene in Black. Grey to order. Will fit either 600 x 300mm or 500 x 250mm slates.aiRFlow: 5,000mm² actual ventilation area.
USe: Slate roof ventilator for use with man-made or natural slates.aDVantaGeS: Long life, simple to install with minimum cutting of slates. Suitable for both batten and sark board fixing.UV light and acid rain resistant. This universal slate ventilator is unique and available for use with the following slate sizes: 600 x 300mm, 500 x 250mm, 450 x 230mm.Stable at temperatures of -40°C to +120°C. May be used for soil ventilation and mechanical extraction when fitted with the HD SPA soil pipe and adapter plate.MateRial: High density polypropylene in Black. Grey to order.aiRFlow: 10,000mm² actual ventilation area.aCtUal BaSe SiZe: 400mm wide x 454mm deep.
USe: Designed for use with the most popular tile profiles, they provide attractive but discrete ventilation entry through the roof surface. With the use of additional adapters they can be fully utilised for both mechanical extraction and soil ventilation.MateRial: Manufactured from high density polypropylene for durability and thermal stability, they have a non-reflective surface and are UV stabilised to prevent embrittlement through age.
ColoURS: The standard through-colour range consists of Terracotta, Brown, Grey and Antique Red although other specific colours are available to order.Vent aRea: Each tile has an actual ventilation area of:HD TV15/1 – 15,000mm²HD TV15/2 – 15,000mm²HD TV15/3 – 15,000mm²HD TV15/4 – 15,000mm²HD TV15/7 – 15,000mm²HD TV10/6 – 10,000mm²HD TV10/8 – 10,000mm²HD TV10/5 – 2,000mm²
tile RooF VentilatoRSHD tV15 SeRieS & HD tV10 SeRieS
Plain tile RooF VentilatoRHD tV10/5
tile tYPe to VentilatoR CoMPatiBilitY
FlUSH FittinG Slate RooF VentilatoRHD ilSRV10/20 & HD ilSRV10/24
HD SRV5U, HD SRV10U, HD SRV10/20 anD HD SRV10/24
all HD tV’s anD HD ilSRV’s
FlUSH FittinG Slate RooF VentilatoRHD ilSRV10/U
USe: Universal slate roof ventilator for use with man-made or natural slates.aDVantaGeS: Long life, simple to install with minimum cutting of slates. UV light and acid rain resistant. Colour through material – stable at temperatures -40°C to +120°C.MateRial anD SiZe: High density polypropylene in Black. Grey to order. Will fit either 600 x 300mm or 500 x 250mm slates.aiRFlow: 10,000mm² actual ventilation area. Adapter available for soil pipe ventilation and mechanical extraction.
HD SPa For use with HD SRV10U, HD SRV10/20 and HD SRV10/24 slate roof ventilators.USe: Connecting 110mm soil vent pipe outlet to 10,000mm² area ventilator.aDVantaGeS: May be used for mechanical extraction when fitted to HD SRV10U and HD SRV680 vents. Length = 500mm.aiRFlow: Total through ventilation area for both adapters is 8,000mm².adapters only available.
USe: A flush fitting slate roof ventilator, for use with natural or man-made slates, available in both 600 x 300mm and 500 x 250mm slate sizes providing discrete air entry through the roof surface as well as providing
for both mechanical and soil extraction via additional adapters. No batten cutting is needed with these ventilators.MateRial: Black high density polypropylene for durability and thermal stability (Grey to order); with non-reflective surface; fully UV stabilised. Stable at temperatures of -40°C to +120°C.aiRFlow: 10,000mm² actual ventilation area.HD ilSRV1020 Base size 565 x 290mm to suit 500 x 250mm slate size.HD ilSRV1024Base size 615 x 300mm to suit 600 x 300mm slate size.
Soil Pipe adapter kit ilSPa. (includes Flexi-Pipe Connector and Blanking Plug)adapter only available.
Hambleside Danelaw Limited surface ventilators require the underlay to be cut to an inverted ‘T’ shape ensuring a close snug fit to the vent spigot or aperture. The cuts forming the ‘T’ should be folded up and back to deflect moisture and debris away from the cut hole in the underlay. This careful preparation will assist in preventing water penetration should other problems exist above the line of the vent, i.e. excessive condensation, cracked / broken or missing slates, etc.
Hambleside Danelaw Limited surface ventilators require the underlay to be cut diagonally to form an envelope ensuring a close snug fit to the vent spigot or aperture. The cuts forming the envelope should be folded up and back to deflect moisture and debris away from the cut hole in the underlay. This careful preparation will assist in preventing water penetration should other problems exist above the line of the vent, i.e. excessive condensation, cracked / broken or missing slates or tiles, etc.
Hambleside Danelaw recommendations
Hambleside Danelaw Limited recommends, in accordance with recognised good tiling practice, that all interlocking tiles should be laid as close to the mid shunt position as possible. Tiles laid too closely together cannot always accommodate the expansion and contraction of the tiles and the roof structure below; this could result in the possibility of the tiles lifting and the interlocks cracking. Likewise, the tile vents may also lift or distort under the compression forces created.
Should difficulty occur in providing conventional cross flow ventilation at eaves level, when maintaining insulation thickness to avoid cold bridging for example, Hambleside Danelaw Limited recommends the use of slate or tile vents positioned as close to eaves level as possible whilst ensuring that they are located above the level of the internal insulation layers.
All Hambleside Danelaw roof ventilation products are suitable for use when the vapour tightness of the ceiling, or the sealing of all joints in and penetrations through VPUs in non-ventilated roof constructions, cannot be achieved or maintained for the life of the roof.
HD TV15/1 HD TV15/2
HD TV15/3 HD TV15/4
HD tVSPa Tile vent adapter kit for use with HD TV15/1, 15/2, 15/3, 15/4 and 15/7 ventilators.
HD RSPa Tile vent adapter kit for use with HD TV10/6 and 10/8 range of ventilators.
HD tV15/1 tile VentMarley Modern TypeRedbank Bretton TypeRedland Mini Stonewold TypeRussells Grampian TypeSandtoft Calderdale TypeQuinn Western Slate MK 2 TypeLagan Flat Type
HD tV15/3 tile VentMarley Double Roman TypeRedland Double Roman TypeRussells Double Roman TypeSandtoft Double Roman TypeLagan Double Roll Type
HD tV10/6 tile VentMarley Ludlow Plus TypeRedland 49 TypeSandtoft Standard Pattern Type
HD tV10/8 tile VentMarley Anglia Plus TypeRedland Norfolk Pantile TypeSandtoft Shire Pantile Type
HD tV15/2 tile VentMarley Mendip TypeRedland Grovebury TypeRussell Pennine TypeQuinn Locherne Type
HD tV15/4 tile VentMarley Ludlow Major TypeRussells Cheviot Type
HD tV15/7 tile VentRedland Renown Type
HD TV15/7HD TV10/6
UniVeRSal Slate RooF VentilatoRHD SRV5U
UniVeRSal Slate RooF VentilatoRHD SRV10U
Slate RooF VentilatoRHD SRV680
ContRaCt VeRSionS aVailaBle in 2 BaSe SiZeSHD SRV10/20 500 x 250mm base size – 10,000mm² actual vent areaHD SRV10/24 600 x 300mm base size – 10,000mm² actual vent areaSuitable for roof and soil pipe ventilation only
Slate Roof Ventilators
Roof Ventilation Products
tile Roof Ventilators
Roof Ventilation Products
HD TV10/8
HD ilSRV10/U Shown here with the Soil Pipe adapter kit HD ilSPaU.
adapter only available.
Minimum rafter pitch: 22.5° or 25° depending on head lap.
Minimum rafter pitch: 22.5° or 25° depending on head lap.
Minimum rafter pitch: 22.5° or 25° depending on head lap.
Minimum rafter pitch: 22.5° or 25° depending on head lap.
Minimum rafter pitch: 22.5° or 25° depending on head lap.
HD PCSPa Tile vent adapter kit for soil ventilation use only with HD TV10/5 ventilator in pairs. Adapters only available.eS10/5 Extension spigots available for fully boarded roofs (not shown).
Soil PiPe aDaPteR KitSUSe: Connecting 110mm diameter pipes for soil ventilation and mechanical extraction. Hose: 510mm Long
aVailaBle aS: Complete adapter kits Code: HD TVSPAfor HD TV15 range and HD RSPA for the HD TV10 range.adapters only available.Vent aRea: 8,000mm² per unit.
KEY
10 11
UniVeRSal RolloUt RiDGe anD HiP SYSteMHD RoR3 anD HD RoR6
USe: A universal Dry Fix ridge system that can be used with all commonly available ridge, tiles and slate types.aDVantaGeS: Can be fitted to all roof pitches with no special tools required. The single unique universal jointing gasket adds flexibility and allows compatibility with most commonly available ridge and hip tile profiles. Broader corrugations than other similar systems at the edge of the RollOut accommodate more types of ridge design and different pitches of roof. Suitable for Hip and Ridge applications. Clips for hip tile cuts provided separately if required.RollOut is available in either 6m (HD ROR6) or 3m (HD ROR3) packs to suit all requirements, large or small.
aiRFlow: HD ROR3 & HD ROR6 provides 5,000mm² airflow area per linear metre making it ideally suited to cold and warm roofs and for batten space ventilation.oPtional HiP tRaY 1.65m long, available in packs of 10, code HDl Ht165. Also available in 3m length HDl Ht300.oPtional tile CliP (code: HD DVC) available for connecting small cuts of interlocking tiles on all Dry Fix hip systems.
UniVeRSal DRY FiX VentilateD RiDGe SYSteMDFR3
USe: A universal Dry Fix ridge system that can be used with all commonly available ridge, tiles and slate types.
aDVantaGeS: Can be fitted in all weathers and to all roof pitches with no special tools required. The system has a minimum number of components, is simple and quick to install with no reliance on adhesive strips.Provides a secure fixing against the weather with easy ridge alignment and discreet appearance.
Supplied 3 linear metres per pack.
aiRFlow: DRF3 provides 5,000mm² airflow area per linear metre to both roof slopes making it ideally suited to cold and warm roofs and for batten space ventilation.
Commonly used as a Dry Fix Ridge installation kit where ventilation is not required.
USe: Semi rigid sleeve designed to ventilate through a standard cavity wall.aDVantaGeS: Accommodates the ‘clip-together’ facility of HD 9300 Air Brick to achieve one, two or three brick fitting.
MateRial: Moulded Black polypropylene.ColoURS: Brown and White
teleSCoPiC UnDeRFlooR VentilatoRHD 9600M
CoMBination BRiCK VentilatoRHD 9300
aiRBRiCK VentilatoR SleeVeSHD 9350/1, HD 9350/2 & HD 9350/3
Telescopic Underfloor Ventilator HD 9600M
Telescopic Underfloor Ventilator HD 9600B with factory fitted Vermin Screen
Optional Cavity TrayHD 9600CT
USe: Designed to be used where the external vent aperture is required to be at a higher level than the underfloor void.aDVantaGeS: Telescopic design gives adjustment from 3 to 5 course height of brickwork (down to 2 if trimmed), and a free airflow in excess of 7,000mm² per unit.USe witH: Factory fitted optional vermin screen Code HD 9600B.Separate optional cavity tray attachment Code HD 9600CT.Separate optional weep ventilator Code HD 9500.MateRial: Injection moulded in black polypropylene.
Vertical extension Sleeve:HD 9610/2A two course vertical extension sleeve for the HD 9600M.Can be used in multiples to achieve any desired height.
Horizontal extension
Sleeve: Designed to extend the reach of the underfloor vent for varying cavity and wall leaf widths.
top extension sleeve:HD 9660t 140mm long for an outer leaf width up to 170mm.
Bottom extension sleeve:HD 9660M 155mm long for an inner leaf width up to 215mm.
USe: Permits high levels of ventilation through walls. Provides entry of air into underfloor voids of suspended floors when used with the Telescopic Ventilator.aDVantaGeS: Standard brick size, ingress protection from driving rain and large insects (4mm flyscreen). Ventilation area in excess of 7,000mm². Bricks may be clipped together for 225 x 150mm or 225 x 225mm combinations.MateRial: Injection moulded in polypropylene – UV stabilised.
ColoURS: Black, Terracotta, Buff, Brown – other colours to special order.aCtUal SiZe: 219 x 79mm.
GaS VentilatoR GRille HD 9300G Factory Fitted Option
USe: HD 9300G gas ventilator to meet with the aperture grille requirement of BS5440-2:2000, section 4 : 1 : 1 : 2 e.g. prevents the entry of a 10mm diameter ball, but allows entry of a 5mm diameter ball. The actual ventilation area of 7,500mm² is depicted on the front of each grille.
Airbrick Ventilator HD 9300
Combination Brick Ventilator HD 9300
Air Brick Ventilator Sleeves HD 9350/1/2/3
Available for one, two and three airbrick combinations
Length: 280mm
Dry Fix Ventilated Ridge Systems
Roof Ventilation Products
telescopic Ventilators and airbricks
Cavity and Underfloor Ventilation
Typical hip installation detail showing optional GRP hip tray.
Typical ridge installation detail.
DFR3 Installations
inteRnal VentilatoR GRille SiZeSHD 9400/1 – 225 x 75mmHD 9400/2 – 225 x 150mmHD 9400/3 – 225 x 225mm
Uni-Ridge Gasket showing how it can accommodate differing tile profiles
Uni-Fixing Clip shown in its low and high positions
Uni-Vent Strip Uni-Filler StripUni-Filler Strip with comb removed
DFR3 Components
12 13
Dry Fix Valley Trough for high profile tiles.
UK Patent No. 2307922
Supplied in packs of 5 units in either 2.4 or 3m lengths.
HDl DVt/1 x 3000mm – lead greyHDl DVt/2 x 2400mm – lead grey
DRY FiX ValleY FoR HiGH PRoFile tileSHDl DVt/1 & 2
DRY FiX ValleY tRoUGH FoR Slate RooFSHDl DVS/1 & 2
Dry Fix Valley Trough for slate roof applications.
UK Patent No. 2307922
Supplied in packs of 5 units in either 2.4 or 3m lengths.
HDl DVS/1 x 3000mm – lead greyHDl DVS/2 x 2400mm – lead grey
DRY FiX ValleY FoR Plain/low PRoFile tileSHDl DVlPt/1 & 2
Dry Fix Valley Trough for plain and low profile tiles.
UK Patent No. 2307922
Supplied in packs of 5 units in either 2.4 or 3m lengths.
HDl DVlPt/1 x 3000mm – lead greyHDl DVlPt/2 x 2400mm – lead grey
PRoDUCt VeRiFiCation
nFRC Hambleside Danelaw are Associate Manufacturing Members of the National Federation of Roofing Contractors and also participate in the Co-Partnership Guarantee Scheme.
BCl Birmingham City Laboratories (formerly Industrial Research Laboratories) certification available from tests carried out on GRP products, Tile Ventilator and Slate Ventilator ranges.
Rapra technology limited Independent tests carried out on the performance of Hambleside Danelaw GRP. Copies of the report are available on request from our Daventry office
SQUaRe to RoUnD aDaPteRHD 9620
UniVeRSal weeP VentilatoRHD 9500
Square to Round Adapter HD 9620
Airbrick/Sleeve HD 9300 and HD 9350
USe: Designed to fit the Telescopic Vent to enable standard 110mm plastic pipes to be connected to allow ventilation to remote underfloor voids.
Asymmetric design suitable for use immediately below pre-cast concrete floors.
MateRial: High Density Polyethylene
USe: Provides ventilating air into the cavity, and when used with cavity tray DPC detailing, allows moisture permeating the cavity area to be returned to the outside.aDVantaGeS: Wall weep and cavity ventilator in the same product. Ideal for all standard detailing – window/door lintels or with airbricks for underfloor/ through cavity venting. Unique internal design allows fitting in either direction. Sealed base of
moisture channel prevents ingress of mortar. Louvre grilles prevent ingress of insects and driven rain.aiRFlow: 260mm² per vent.MateRial: Injection moulded polypropylene, UV stabilised.ColoURS: White, Black, Buff, Terracotta, Brown, Grey and Translucent.
Suitable for traditional build and timber frame construction.
aPPliCationS
Telescopic Underfloor VentHD 9600M
Weep Vent and Stop End Assembly
PeRP weeP PeRP eXtenSionHD 9100 HD 9200
USe: Allows the release of moisture above lintels and cavity trays.SiZe: Height = 70mm
Length = 100mm.MateRial: Polypropylene.ColoURS: Translucent, Buff,Terracotta
USe: Perp Weep Extension clips to the Perp Weep singularly or in multiples to accommodate different outer leaf constructions – e.g. render of different thicknesses.SiZe: Height = 70mm
Length = 30mm.MateRial: Polypropylene.
Perp Weep Extension HD 9200
Perp Weep HD 9100
lintel StoP enDHD 9800
USe: A lintel stop end for use at the ends of most popular DPC steel lintels. The HD 9800 provides a stop end preventing discharge of water into the cavity.USe witH: HD 9800 Lintel Stop Ends may also be applied to a range of cavity trays. Now recommended by the NHBC and BS 8215 1991.
BeneFitS:n Adjustable to most shapes
and types of lintels for a secure fit.
n Ensures consistent and compliant build detail.
n Integral bonding strip on the base.
MateRial: Polypropylene.
Lintel Stop End HD 9800
Weep Vent HD 9500
Square to Round Adapter HD 9620
Cavity and Underfloor Ventilation
Dry Fix Valley troughs
GRP Flashings Products
In the case of interlocking single lap tiles, where small cuts of tiles occur, with HDL DVT and HDL DVLPT Valleys. the smaller cut section may need to be supported using a ‘support bridge’ UK Patent No. 2307922, positioned over the inner water bar.
Alternatively a stainless steel tile clip, HD DVC, may be used as illustrated. This support should only be required on the left side of the valley where no support is available from the tile interlock, ref. BBA Certificate No. 87/1915.
SMall CUt tile SUPPoRt BRiDGeHD DVBP
HD DVBP
HD DVC
360
55
360
80
105
360
n Up to half the cost of traditional lead installation
n Semi-skilled fitting procedure
n Reduce installation time and cost by up to 50%
n Pre-formed profiles are light in weight and easy to handle
n BBA approved
n 30 year guarantee
n Third party testing accreditation by RAPRA Technology and Birmingham City Laboratories
n Does not streak or stain slates or tiles
n Can be safely used with other products to recycle rainwater
n No value to the thief
Dry Fix mortarless GRP Valley Trough creates close-cut appearance on new build and refurbishment. Suitable for all profiled tiles. Available in standard lead grey colour, this uniique product cuts fixing time by up to 50%. GRP valley troughs provide the following advantages over lead products
14 15
Plain Tiles
Batten
Roof Underlay
Valley Board
Rafter
Dry Fix Valley
Slates
Batten
Roof Underlay
Rafter
Valley Board
Dry Fix Valley
tile ValleY tRoUGHSHD 401, 402, 361 & 362
A popular valley trough incorporating mortar retention bars adjacent to the bonding strip.
Supplied in packs of 10 units.
HDl 401 Standard lead grey W410mm x L3000mmHDl 402 Standard lead grey W410mm x L2400mm
Also available 380mm wide –HDl 361 Standard lead grey W380mm x L3000mmHDl 362 Standard lead grey W380mm x L2400mm
A basic ‘contract’ valley trough with mortar bonding strips.
Supplied in packs of 10 units.
HDl RP3 Standard lead grey W380mm x L3000mmHDl RP4 Standard lead grey W380mm x L2400mm
Designed for use with both natural or man-made slates.
HDl SVtU For slate roofsSupplied in packs of 10 unitsW360mm x L3000mm
Also available 330mm wideHDl SVt For slate roofsSupplied in packs of 10 units.W330mm x L3000mm
tile ValleY tRoUGHSHDl RP3 & HDl RP4
Slate ValleY tRoUGHSHDl SVtU & HDl SVt
20517.5°
205
Rafter Pitch Required Valley Maximum Required Valley Maximum Minimum lap (degrees) Product Code length (m) Product Code length (m) length (mm)
17.5 to 22 401/2 SVTU 7.0 Not applicable Not applicable 350
22.5 to 29 RP3/4, 361/2, 401/2, SVT, SVTU 7 0 401/2, SVTU 14.5 300
30 to 34 RP3/4, 361/2, 401/2, SVT, SVTU 7.5 401/2, SVTU 15.0 200
35 to 39 RP3/4, 361/2, 401/2, SVT, SVTU 7.5 401/2, SVTU 15.5 200
40 to 44 RP3/4, 361/2, 401/2, SVT, SVTU 8.0 401/2, SVTU 16.5 150
45 to 49 RP3/4, 361/2, 401/2, SVT, SVTU 8.5 401/2, SVTU 17.0 150
50 to 55 401/2, SVTU 9.0 401/2, SVTU 18.5 150
Roof area less than 25m² Roof area from 25m² to 100m²
CHooSinG tHe RiGHt ValleY tRoUGH PRoFile
Designed specifically for a traditional boarded roof detail, this unique valley trough is fitted directly to the sarking board. For roof areas of less than 25m² and rafter pitches from 22.5° to 49°.
Supplied in packs of 10 units.
HDl SSVt Scottish Slate Valley Trough W360mm x L3000mm
190 19017.5°
180 18017.5°
180 18022°
SCottiSH Slate ValleY tRoUGHHDl SSVt
Slates
Batten
Roof Underlay
Counter Batten
Valley Board
Rafter
Valley Trough
Tiles
Batten
Roof Underlay
Counter Batten
Mortar
Valley Trough
Valley Board
Rafter
Slates
Roof Underlay
Sarking Board
Rafter
Valley Trough
DRY FiX ValleY FoR HiGH PRoFile tileSHDl DVt/1 & 2
DRY FiX ValleY FoR SlateSHDl DVS/1 & 2
tile ValleY tRoUGHSHDl 401 & 402, HDl 361 & 362, HDl RP3 & RP4
Slate ValleY tRoUGHSHDl SVtU & SVt
Tiles
Batten
Roof Underlay
Valley Board
Rafter
Dry Fix Valley
DRY FiX ValleY FoR Plain / low PRoFile tileSHDl DVlPt/1 & 2
SCottiSH Slate ValleY tRoUGHHDl SSVt
50 50
50 50
tYPiCal waRM RooF inStallation
Tiles
Tiling Batten
Counter Batten
Roof Underlay
Counter Batten
Valley Board
Mortar
Valley Trough
Insulation
tYPiCal waRM RooF inStallation
Tiles
Tile Batten
Counter Batten
Roof Underlay
Valley Board
Insulation
Dry Fix Valley
GUiDanCe noteS on ValleY tRoUGH inStallation
Guidance notes on valley trough installation can be found in the following publications, particularly with reference to valley board construction, the use of underlay and counter battens.
BS 5534:2003 BBa Certificate No. 87 / 1915 nFRC Technical Bulletin No. 28
StormForce 225 High Performance Valley troughs
GRP Flashing Products
installation of GRP Valley troughs
GRP Flashing Products
1
2
3
4
5
6
1
2
3
4
5
6
7
8
1
4
2
5
3
6
1
4
2
5
7
3
6
8
1
2
3
4
5
6
1
4
2
5
3
6
1
2
3
4
5
6
7
1
4
2
5
7
3
6
1
2
3
4
5
6
1
4
2
5
3
6
1
4
2
5
3
1
2
3
4
5
1
2
3
4
5
6
7
1
4
2
5
3
67
1
2
3
4
5 8
6 9
7
1
4
2
5
3
67
89
our range of Stormforce 225 high performance open valley troughs comply with nFRC technical Bulletin 28.
16 17
A damp proof course specially developed for sloping parapet wall applications incorporating a wide mortar bonding strip.
Supplied in packs of 10 units.
SiZe: W310mm x L2440mm
Replaces the need to cut slates to form the first support eaves course.
Supplied in packs of 10 units.
SiZe: W355mm x L3000mm
DaMP PRooF CoURSeHDl DPC
ContinUoUS eaVeS CoURSeHDl CeCS
245
355
A continuous GRP cover flashing in standard lead grey colour as an attractive and cost effective alternative to lead for all roof abutments.Easily trimmed on site to suit the application.
SiZe: H150 x W45 x L3000mm
UniVeRSal aBUtMent CoVeR FlaSHinGHD UaCF
Coping stone
Mortar bed
GRP Conti-Soakerfor slates – LippedHDL CSS
HDl DPC
GRP flashingHD UACF
GRP Conti-Soakerunlipped – HDL CST
45
150
USe: Creating a successful weather tight joint between dissimilar roof coverings, e.g. slate to tile, or different profile concrete tiles on terraced or semi-detached housing.
Supplied in packs of 10 units.
HDl DBG1 is 210mm wide and manufactured to a length of 3m with a central upstand height of 70mm to suit slates, flat interlocking tiles and plain tiles.
HDl DBG2 is 210mm wide and manufactured to a length of 3m with a central upstand height of 100mm to suit profiled tiles on one or both sides and also typical Scottish practice where there may be tiling battens on one side only.
DRY FiX BonDinG GUtteRHDl DBG1 & HDl DBG2
210
70
Bonding Gutters
GRP Flashing Products GRP Flashing Products
210
100
123456789
tYPiCal FiRe BReaK inStallationHDl BG
Tiles
Mortar Bed
Bonding Gutter
Slates
Batten
Roof Underlay
Rafter
Mortar Barrier
Party Wall
1
2
3
4
5
6 9
7
8
Dry Fix solution for a mortar-free roof
USe: To join dissimilar roof coverings, e.g. slate to tile, or different profile concrete tiles on terraced or semi-detached housing.
Supplied in packs of 10 units.W225mm x L3000mm
225
BonDinG GUtteR™HDl BG
1234
678
5 5
tYPiCal StanDaRD inStallationHDl BG
Tiles
Mortar Bedding
Bonding Gutter
Slates
Batten
Roof Underlay
Rafter
Party Wall
1
2
3
4
5
6
7
8
traditional solution for mortar bedding
Tiles
Bonding Gutter
Slates
Batten
Roof Underlay
Rafter
Party Wall
Counter Batten
Sarking Board
Mortar Barrier
Tiles
Bonding Gutter
Slates
Batten
Roof Underlay
Rafter
Party Wall
Counter Batten
Sarking Board
1
2
3
4
5
6
7
1
2
3
4
5
6
7
10
1
2
3
4
5
6
7
8
9
tYPiCal FiRe BReaK inStallationHDl DBG
tYPiCal SCottiSH inStallationHDl DBG
tYPiCal StanDaRD inStallationHDl DBG
Tiles
Bonding Gutter
Slates
Batten
Roof Underlay
Rafter
Party Wall
1
2
3
4
5
6
7
1
2
3
5
6
7
8
9
4
1
2
3
5
6
7
8
9
10
4
18 19
Supplied in packs of 50 units.
Suitable for use with Redland Richmond type tiles. Left hand and right hand. H75 x W180 x L430mm
HD RRS/l - Left handedHD RRS/R - Right handed
SiZe: H75 x W180 x L430mm
Also available:HD SRRS/l & RSuitable for use with Russell Galloway type tiles and Marley Edgemere type tiles.
Supplied in packs of 50 units.
For interlocking flat concrete tiles – suitable for use with Marley Modern, Redland Stonewold and equivalent tile types.
HD MDS/l - Left handedHD MDS/R - Right handed SiZe: H75 x W185 x L430mm
inteRloCKinG tileSHD RRS/l & R
SlateSHD SS500 & HD SS600
inteRloCKinG tileSHD MDS/l & R
Plain tileSHD PCS/l & R
Supplied in packs of 50 units.
SS500 Slate soaker for 500mm x 300mm slates.SiZe: H85 x W100 x L250mm
SS600Slate soaker for 600mm x 300mm slates.SiZe: H85 x W100 x L380mm
Supplied in packs of 50 units.
HD PCS For plain clay and concrete tiles.
HD PCS/l - Left handedHD PCS/R - Right handed SiZe: H75 x W100 x L165mm
All Hambleside Danelaw Dry Soakers are quick and simple to install. Made from lightweight high density polyethylene they are available for both tile and slate roofs in right and left handed versions. They are made from lightweight, high density polypropylene chosen for its thermal stability, resistance to UV light, acid rain and cracking under temperature change.
Continuous Soaker for tiles with mortar bonding strip.
Available in Lipped and Unlipped versions for tile roofs, they can be fitted in approximately half the time it takes to install lead.
Supplied in packs of 10 units.
SiZe:lippedH150 x W170 x L3000mmUnlippedH140 x W170 x L3000mm
Available in Lipped and Unlipped versions for slate roofs, they can be fitted in approximately half the time it takes to install lead.
Supplied in packs of 10 units.
SiZe: lippedH150 x W170 x L3000mmUnlippedH140 x W170 x L3000mm
Also available for Scottish slate practice:
Conti-SoaKeR™ FoR SlateHDl CSS
Conti-SoaKeR™ FoR tileSHDl CSt
tYPiCal inStallation DetailS
170170
UNLIPPED SLATE VERSION
SCOTTISH VERSION
UNLIPPED SLATE VERSION
LIPPED TILE VERSION
LIPPED TILE VERSION
UNLIPPED TILE VERSION LIPPED SLATE VERSION
LIPPED SLATE VERSION
Tile Mortar
Lip set in mastic
Counter battenBearerRafter
UACF or Stepped lead flashing
Tile Mortar
Counter battenBearerRafter
UACF or Stepped lead flashing
BearerRafter
Counter batten
Lip set in mastic
SlatesCounter batten
BattenBearerRafter
Render withBell Cast
Slates
Sarking Board
Rafter
Conti-Soaker™ Continuous Soakers
Flashing Products
Dry Soakers
Flashing Products
150 140
200
160
170
140
75 185
18575
100
100
85
75
HD MDS/R
HD RRS/R
HD SS500 & HD SS600
HD PCS/R
HDl SCSS Conti-Soaker™.
170
150
20 21
For slate roof – sark board or over batten fixing.
Supplied in packs of 10 units.
GaP: 16mm lenGtH: 3000mm
USe: Continuous eaves closure and vermin stop which adapts to the tile profile. Easy to handle and maintenance free. Quick to fix, with slotted nail holes. Compatible with pantiles. Prevents ‘cocking’ of tiles at the fascia.
SiZe:Universal CombHeight: 66mmLength: 1 metreMateRial: Black LDPE.
USe: Provides full support and eaves protection for roofing underlay at eaves level. Combines to provide drip into guttering.
BeneFitS: Clips together for universal rafter spacing. Hinged at fascia to prevent panel distortion on low pitches.
Fixed with HD 12000M or HD 12000U or directly to the top of the fascia board.
CoVeRaGe: 600mm per panel.MateRial: Black PVC.
USe: An optional extra, the diversion plate provides additional security, if required, against debris and moisture penetration when fitted with either flush fitting slate or tile ventilators.
MateRial: Black PVC.
USe: Provides straightforward access through ceilings into loft spaces.aDVantaGeS: Easy to install, maintenance free, with no need to paint. Loft access door panel offering an integral draft/vapour seal. Push up version is fitted with two catches to provide secure closing and prevent uplift. The hinged version is suitable for use with a telescopic loft ladder.
MateRial: White injection moulded polypropylene with integral insulation.SiZeS: All models meet or exceed the NHBC minimum opening size of 520mm in any direction and suit 600mm joist centres. They can be used with other joist centres by cutting a joist and trimming the opening in an approved manner.
UnDeRlaY SUPPoRt tRaYHD 3000
USe: Ideally suitable for eaves refurbishment details, this rigid pvc unit provides an immediate and cost effective solution to situations where damage to the underlay has occurred.note: The Rigid Underlay Support Tray should be nailed to the top of the fascia board.
USe: The Underlay Support Tray can be used in conjunction with either traditional soffit strip ventilator configurations (HD 8000 and HD 8250) or with over fascia ventilators (HD 12000M or the HD 12000U universal).lenGtH: 1500mmMateRial: Black PVC.
RiGiD UnDeRlaY SUPPoRt tRaYHD RFSt
MoiStURe DiVeRSion PlateHD il/DP
loFt aCCeSS tRaP DooRSHD tRaPPU & HD tRaPDD
thermal PerformanceBuilding Regulations Approved Document C 2004 Edition requires that in order to resist surface condensation and mould growth, a roof should be designed and constructed so that the thermal transmittance does not exceed 0.35W/m²K at any point.
ContinUoUS DRY VeRGeHDl DV6
ContinUoUS DRY VeRGeHDl DV8
For slate roof under batten fixing. Counterbattens fitted between slate battens are recommended to provide closure to the batten cavity when using HDL DV6 & HDL DV8.
Supplied in packs of 10 units.
GaP: 40mm lenGtH: 3000mm
For slate and plain tiles – face fixing.
Supplied in packs of 10 units.
GaP: 55mm lenGtH: 3000mm
Standard architrave mouldings can be fitted to the barge board to conceal Dry Verge fixings and enhance finished appearance.
40
55
35
16
Ridges The Dry Verges are cut with a vertical mitre and butt jointed. A lead saddle may be fitted over the joint if required. The ridge tile should be trimmed if neccessary to suit.
Verge Joints Where joints in the Dry Verge are required along the edge of the roof, they should be overlapped with the lower section fitted over/around the upper section.
Sprockets Slight or gentle sprockets can easily be accommodated by cutting the lower section to a slight rake and fitting over the upper or main Dry Verge section.
note:These jointing methods are suitable for all of the Dry Verge profiles.
Sprocket JointFig. 1
Sprocket JointFig 2
Dry Verge Joint Details
Ridge Joint
Verge Joints
ContinUoUS SCotVeRGeHDl DV7
For slate roof – face fixing for sark board detail.
Supplied in packs of 10 units.
GaP: 35mm lenGtH: 3000mm
Dry Verges
GRP Flashing Products ancillary Products
ContinUoUS SCotVeRGeHDl DV9
eaVeS CoMB FilleRHD eCFM
alSo aVailaBle: 0.35W/m²K rated Drop Down HD tRaP DD 350.35W/m²K rated Push Up HD tRaP PU 35NOTE: For lockable loft access doors please contact our sales office.
Push up version HD tRaPPU
Drop down version.HD tRaPDD
Steel loft access door, fire rated to Class 0.HD tRaPDDF
Continuous Dry Verges have been developed for use with both natural and fibre cement slates giving the advantages of all weather fixing and permanent wind protection; a product which is simple to install without complicated interlocking methods. Scotverges have been developed for typical Scottish slating practice
Hambleside Danelaw Building Products
Hambleside Danelaw limitedlong MarchDaventry northamptonshire nn11 4nR
telephone01327 701900Fax01327 701909e-mailmarketing@hambleside-danelaw.co.ukwebwww.hambleside-danelaw.co.uk
The Company has a continuing product development programme. News relating to these products, or technical developments, is issued regularly in the form of Information and Data Sheets.
Communication with our customers is welcomed on all subjects relating to the performance of products, or on their use on-site. In accordance with our policy for continuous improvement we reserve the right, should the need arise, to amend product specifications without prior notice.
Terms and Conditions of Sale are available upon request.
The Company reserves the right to implement a 25% restocking charge for returned goods.
All images are for illustration purposes only and Hambleside Danelaw reserve the right to amend specifications without prior notice.
the Group and the environmentHambleside Danelaw has developed a comprehensive environmental policy, embracing the key issues of greenhouse gas emissions, sustainability and recycling of product at end of life. Full information on the environmental policies of Hambleside Danelaw, including its Corporate Social Responsibility statement, is available from our website.
5395.02.2012