Download pdf - Grease Testing Solutions - Petroleum Test Equipment ... · the surface by a free fall at a standard temperature. Setamatic Penetrometer (17500-0) ASTM D1403, ASTM D1831, ASTM D217,

Grease Testing SolutionsLaboratory Instruments for quality control, analysis and

calibration

Stanhope-Seta, London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: [email protected] | www.stanhope-seta.co.uk

Image kindly provided by

Axel Christiernsson International AB

Seta Part No: 19900-3 (Autoload) 19800-7 (Manual)

Speed Range: 1200 to 1760rpm 1200 to 1760rpm

Load Range: 40 to 800kgF 0 to 800kgF

Timing: 0.1s to 9999hr 0.1s to 9999hr

Voltage: 220/240V 50/60Hz 220/240V 50/60Hz

Power: 2.6kW 2.6kW

Size (HxWxD) / Weight: 169 x 63 x 62cm / 150kg 169 x 82 x 62cm / 161kg

Seta-Shell 4-Ball Lubricant Testers (19800-7 & 19900-3)ASTM D2596, ASTM D2783, ASTM D2266, ASTM D4172, CEC L-45-T-99, EN ISO 20623, IP 239, ISO CD 11008, ISO 26422, DIN 51350-1,4,5,6

• Applied loads range up to 800kgF

• Drive speed from 1200 to 1760rpm

• Digital timer and display with selectable range 0.1s to 9999hr

• Digital displays and microprocessor control of Applied Load and Torque (19900-3)

• Automatic Torque limiting and cut-off

• Interlocked guards for maximum safety

• Optional heating pad and controller

• Unique test ball loading/removal tool

Visit: www.stanhope-seta.co.uk/4913/Seta-Shell-4-Ball-Tester-Autoload

› 19900-3


Grease Testing SolutionsLaboratory instruments for quality control,

analysis and calibration

2

Wear Loading Kit (19940-0)ASTM D2266, ASTM D4172

The optional Wear Loading Kit converts the auto-load 4-Ball Tester (19900-3) to a manual system (19800-7) allowing low loading/greater sensitivity as required by D2266 and D4172.

Emergency stop

Perspex guard

Torque limit switch

› 19940-0

∞ Designed with safety and efficiency in mind ∞

› 19815-0

Extreme Pressure & Anti-WearThe Seta-Shell 4-Ball Lubricant Tester determines the friction properties of extreme pressure oils and greases and shear stability of lubricating oils.

A sliding motion under high pressure is produced between steel balls, largely simulating conditions that occur in gears and metal cutting operations.

Ball Loading/Release Device (19815-0)

Easily insert and remove the test ball into the drive chuck of the 4-Ball.

Seta-Shell 4-Ball Lubricant Testers (19800-7 & 19900-3)ASTM D2596, ASTM D2783, ASTM D2266, ASTM D4172, CEC L-45-T-99, EN ISO 20623, IP 239, ISO CD 11008, ISO 26422, DIN 51350-1,4,5,6

• Applied loads range up to 800kgF

• Drive speed from 1200 to 1760rpm

• Digital timer and display with selectable range 0.1s to 9999hr

• Digital displays and microprocessor control of Applied Load and Torque (19900-3)

• Automatic Torque limiting and cut-off

• Interlocked guards for maximum safety

• Optional heating pad and controller

• Unique test ball loading/removal tool

Visit: www.stanhope-seta.co.uk/4913/Seta-Shell-4-Ball-Tester-Autoload

Grease Testing Solutions


3

Laboratory instruments for quality control, analysis and calibration

Water Washout Tester (19610-4)ASTM D1264, IP 215, ISO 11009, DIN 51807-2

• Large access panels for test hub and pump

• Recirculating bypass valve for pre-heating

• Rapid warm up time

• Fully removable pump for servicing

• Integral bath drain

• Separate electronics compartment for added safety

• Easy to calibrate

Visit: www.stanhope-seta.co.uk/3479/Seta-Water-Washout-Tester

Dual Water Washout Tester (19650-0)ASTM D1264, IP 215, DIN 51807-2, ISO 11009

• Twin bearing and housings for duplicate or independent testing

• Two separate water tanks and jets

• All parameters are independently adjustable

• Testing at 38 and 79°C (100 and 175°F) as per ASTM D1264

• Magnetic bearing drive for easy disassembly and removal

• Automatic test procedure and display of test parameters

• Spacious and easy to clean water tank

• All water wet parts are resilient to salt water

Visit: www.stanhope-seta.co.uk/4863/Dual-Water-Washout-Test

› 19610-4

Seta Part No: 19650-0 19610-4

Rotational Speed: 600 and 3780rpm (variable options available) 600 ±30rpm

Temperature Range: Ambient to 80°C Ambient to 80°C

Voltage: 220/240V 50Hz 110/120V 50/60Hz or 220/240V, 50/60Hz (switchable)

Size (HxWxD) / Weight: 60 x 85 x 52cm / 55kg 30 x 40 x 40cm / 24kg

› 19650-0

Water WashoutWater Washout Testers are used to evaluate the resistance of a lubricating grease to be washed out of a bearing by water.

Distilled water, temperature controlled at either 38°C or 79°C is pumped at a specified flow rate from a water tank through a nozzle and sprayed onto a grease-packed rotating test bearing. The amount of grease washed out of the bearing during a one hour period is a measure of the resistance of the grease to water washout.

Water washout instruments are supplied with a test bearing for laboratory commissioning.




4

Stanomatic Dual Grease Worker (17790-2 & 17792-2)ASTM D217, ASTM D7342, IP 50, ISO 2137

• Quick release heavy duty brass or stainless steel worker cups

• Works two grease cups simultaneously

• Auto-stop at up to 99,999 strokes

• 60 ±10 strokes per minute

• Cover and plunger assemblies with 51 x ¼ inch hole perforated plates

• Safety screen with auto shut off

• Large bore cock for thermometer insertion

The Stanomatic Dual Grease Worker simulates the working of the grease in service.

Grease Worker with Brass Cups (17790-2)

Visit: www.stanhope-seta.co.uk/4097

Grease Worker with Stainless Steel Cups (17792-2)


Quick Release Worker Cups, Brass (17510-201) & Stainless Steel (17525-2)• Two brass cups are supplied with the 17790-2

• Two stainless steel cups are supplied with the 17792-2

• Quick release worker cups screw on and off in two steps

› 17790-2

Roll Stability Testers (19400-5)ASTM D1831; MIL-G-10924

• 165rpm

• 100 to 200rpm variable speed control option

• Air bath temperature ranges up to 200°C

• Integral timer

• Four test cylinder capacity

• Polished Stainless steel or Mild Steel cylinder/roller options

• Optional venting hood for ambient tests

Seta offer a range of three roll stability instruments which are ruggedly designed for extended periods of use.

The 19400-5 and 19450-0 instruments allow extended temperature testing up to 200°C with variable speed control available as an option on the 19450-0 model.

The 19400-3 model is suitable for testing up to 100°C.

High Temperature Roll Stability Tester (19400-5)


High Temperature Roll Stability Tester & Speed Control (19450-0)


Roll Stability Tester (19400-3)

Visit: www.stanhope-seta.co.uk/1026 › 19400-5

∞ Designed for continuous use, robust and hardwearing ∞

Shear StabilityShear stability of a grease is its ability to withstand repeated working with minimum change to its structure or consistency.



5


Drop PointThe dropping point of grease is the temperature at which greases passes from a semi-solid to a liquid state and indication of its heat resistance.

Seta Grease Drop Point Oven (11730-3)ASTM D2265, ISO 6299

• Aluminium solid block oven

• Six test apertures

• Temperature range 120 to 345°C

• Illuminated chambers

• Non mercury thermometer

Visit: www.stanhope-seta.co.uk/4351/Seta-Grease-Drop-Point-Oven

CorrosionThe EMCOR test measures the ability of a grease to protect a bearing against corrosion in the presence of water to maximise running time.

Two bearings per test are run in the machine, which is partially immersed in water, at a speed of approximately 80 r/min in a predetermined sequence of running/stopping over a period of one week. At the end of the test the raceways of the bearing outer rings are inspected for rust.

EMCOR Test Machine (19300-0) ASTM D6138, DIN 51802, IP 220, ISO 11007

• 8 test positions

• 8 pieces specially treated 1306K/236725 double row self-aligning ball bearings

• 80 rpm ±5

• Digital control unit and timer

• Optional safety cover

• Optional washout pump and tubes

• Suitable for distilled or demineralised water, salt water or synthetic sea water

Visit: www.stanhope-seta.co.uk/4899/EMCOR-Test-Machine1

1 Shaft with protective nylon coating

2 Distilled or demineralised water, salt water or synthetic sea water

3 Test bearing and testing grease/oil

› 19300-0

› 11730-3

80 r/min

1 2 3




6

› 17190-3

PenetrationPenetration determines the consistency or hardness of a grease by measuring the distance a standard cone will penetrate the surface by a free fall at a standard temperature.

Setamatic Penetrometer (17500-0)ASTM D1403, ASTM D1831, ASTM D217, ASTM D7342, ASTM D937, IP 179, IP 310, IP 50, ISO 2137

• Microprocessor controlled automatic penetrometer

• Penetration range 0 to 630 Pen (63mm)

• Timer range 1 to 9999 seconds

• Automatic plunger release and retention

• Flexi light & inbuilt spirit level

• RS232C interface

Visit: www.stanhope-seta.co.uk/939/Setamatic-Penetrometer

Semi-Automatic Universal Penetrometer (17190-3)ASTM D1403, ASTM D1831, ASTM D217, ASTM D7342, ASTM D937, IP 179, IP 310, IP 50, ISO 2137

• Penetration range 0 to 640 Pen (64mm)

• 5, 8, 10, 12, 30 and 60 second timer settings

• Solid state timer

• Automatic plunger release and retention

• Flexi light & inbuilt spirit level

• RS232C interface

Visit: www.stanhope-seta.co.uk/4428/Seta-Universal-Penetrometer

› 17500-0



7


› 20990-0

› 18000-0

Seta ASTM-IP Cone (18000-0)ASTM D217-IP 50, ASTM D937-IP 179, ISO 2137

• Brass (hollow) conical body

• 3.17mm (1/8 inch) stem diameter

• 102.5g ±0.05g mass

• Optional UKAS certification

SeparationThe oil separation test determines the tendency of oil to separate from a lubricating grease when under pressure.

Seta Pressure Bleeding Test Cell Type B (20990-0)ASTM D1742, FTM 791 322

Comprises a tightly fitting cap and cover which contains a 75µm (No. 200) sieve strainer, a funnel for collecting separated oil and a 25ml beaker for retaining the oil.

Seta Grease Separation Apparatus (20900-0)BS 2000 Part 121, DEF 222A CS 3107, DIN 51 817, IP 121

Comprises a stainless steel separation cup with ISO 3310-1 metal gauze cone, 100g stainless steel weight and an oil cup.

Seta ASTM-IP Standard Penetrometer Cone (18140-0)ASTM D217-IP 50, ASTM D937-IP 179, ISO 2137

• Acetal (solid) conical body

• 3.17mm (1/8 inch) stem diameter

• 102.5g ±0.05g mass

• Optional UKAS certification› 18140-0

› 20900-0

Stanhope-Seta, London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: [email protected] | www.stanhope-seta.co.uk | Issue 2


Test Method: Test Description: Instrument: Seta Part No:

ASTM D217 BS 2000-179DIN 51 580

ISO 2137 Cone penetration of petrolatumStanomatic Dual Grease Worker, Pentrometer

17790-2, 17792-2, 17500-0, 17190-3

ASTM D1264 FTM 791 3252 IP 215 ISO 11009 Determination of water washout characteristics of lubricating grease Water Washout Tester 19610-4, 19650-0

ASTM D1403 IP 310Cone penetration of lubricating grease using one-quarter and one-half scale cone equipment

Penetrometer 17500-0, 17190-3

ASTM D1742 Oil separation from lubricating grease during storage Pressure Bleeding Test Cell 20990-0

ASTM D1831 Roll stability of lubricating grease Roll Stability Tester 19400-5

ASTM D2266 ISO 6299 Dropping point of lubricating grease over wide temperature range Grease Drop Point Oven 11730-3

ASTM D2596 Measurement of extreme pressure properties of lubricating grease 4 Ball Lubricant Tester 19800-7, 19900-3

ASTM D6138Determination of corrosion preventative properties of lubricating greases under dynamic wet conditions

EMCOR Test Machine 19300-0

ASTM D7342 Shear stability of lubricating greases in presence of water Stanomatic Dual Grease Worker 17790-2, 17792-2

BS 2000-50 IP 50 Determination of cone penetration of lubricating greaseStanomatic Dual Grease Worker, Penetrometer

17790-2, 17792-2, 17500-0, 17190-3

BS 2000-121 IP 121Determination of oil separation from lubricating grease using pressure filtration

Grease Separation Apparatus 20900-0

DIN 51802 Evaluates the rust preventive properties of greases EMCOR Test Machine 19300-0

FTM 791 322 Oil separation from lubricating grease during storage Pressure Bleeding Test Cell 20990-0

MIL-G-10924 Roll stability Roll Stability Tester 19400-5

IP 220Determination of rust prevention characteristics of lubricating greases and oils in the presence of an aqueous test fluid


ISO 11007Measures the ability of a grease to protect a bearing against corrosion in the presence of water
