Operating Instructions
http://www.fujiimpulse.co.jp
FA Series
Automatic Impulse Sealer
Printed JAN 20112nd Edition 2.01E
FA Series Operating Instructions Ver2.01E
This manual is designed to cover machines of various voltages and plug configurations
About the warning labels
Foreword
The warning labels indicate when there is a danger of injury to the operator or damage to the ma-chine.
Below is a list of what each label denotes.
Caution Minor injuries or damages to the unit may occur when the instruction is ignored.
Warning Critical injuries or fatal accidents will almost certainly occur when the instruction is ignored.
Danger Critical injuries or fatal accidents will almost certainly occur when the instruction is ignored.
Attention! Important Notes and Restrictions - Read the directions in order to avoid misuse of the unit.
TIPS Great Tips and References when using the unit - Highly recommend reading through the information.
Before using, always verify the voltage specification of your particular unit and operate it at the correct voltage.
Please note the following:
1) The voltage specification of your unit is listed on the label which displays the serial number. This label can be found on the machine body.
2) The explanations and illustrations in this operators' manual utilize the following standard plug configurations most common in Japan. However, due to the various configurations in use worldwide, these may not necessarily correspond with the one attached to your specific unit.
100V15A以下
200V20A
100V20A
200V30A
100V20A、30AWarning Voltages and plug configurations differ according to various worldwide specifications.
Always verify those of your particular unit before beginning operation. Connecting the power cord to an outlet of a different specification is extremely hazardous.
Thank you for purchasing the Fuji Impulse FA series sealer. Please read all of the safety and operating instructions before operating this machine. Periodic maintenance and proper operation are necessary to ensure safety when using this impulse sealer.Keep this manual on hand when operating the sealer. Set the heating time according to the material and thickness of the film. As a result of research to further improve the FA series, some details in the operating instructions may differ from your actual machine. For operating problems or product information, please contact your local dealer or fax Fuji Impulse at (81)6-6335-1828.
FA Series Operating Instructions Ver2.01E
3
Table of contents1 Specification ………………………………………………………………………………………… 5
2 Package contents …………………………………………………………………………………… 6
3 Replacement parts …………………………………………………………………………………… 7
4 Proper use of the sealer …………………………………………………………………………… 7
5 Warning-caution label location and content …………………………………………………… 8
6 Operating precautions ……………………………………………………………………………… 9For safety operation…………………………………………………………………………………………………………………………… 9
For smooth operation ……………………………………………………………………………………………………………………… 11
Other safeguards …………………………………………………………………………………………………………………………… 12
7 Major parts and function ………………………………………………………………………… 13
8 Proper use of the sealer ………………………………………………………………………… 148-1 Setting the machine ………………………………………………………………………………………………………………… 14
8-2 Mounting the table ………………………………………………………………………………………………………………… 14
8-3 Insert the air hose…………………………………………………………………………………………………………………… 15
8-4 Plugging in the electrical power cord. …………………………………………………………………………………………… 15
8-5 Power switch ON …………………………………………………………………………………………………………………… 16
8-6 Select the operation mode ………………………………………………………………………………………………………… 16
How to set each operation mode …………………………………………………………………………………………………… 17
8-7 Setting the sealing condition with the control unit ……………………………………………………………………………… 17
8-8 Adjust the seal pressure …………………………………………………………………………………………………………… 20
8-9 Perform test sealing ………………………………………………………………………………………………………………… 20
8-10 Seal with the selected operation mode …………………………………………………………………………………………… 21
8-11 Finishing sealing …………………………………………………………………………………………………………………… 22
8-12 Counter reset………………………………………………………………………………………………………………………… 22
8-13 Power switch OFF ………………………………………………………………………………………………………………… 22
8-14 Inspection after operation ………………………………………………………………………………………………………… 22
9 Replacing the routine maintenance parts …………………………………………………… 239-1 Preparation ………………………………………………………………………………………………………………………… 23
9-2 Sliding the Teflon sheet …………………………………………………………………………………………………………… 24
9-3 Replacing the heating element …………………………………………………………………………………………………… 25
9-4 Replacing the glass tape and Sarcon sheet……………………………………………………………………………………… 27
9-5 Replacing the silicone rubber ……………………………………………………………………………………………………… 28
9-6 Replacing the pressure rubber …………………………………………………………………………………………………… 28
9-7 Replacing the microswitch ………………………………………………………………………………………………………… 29
10 Adjusting each part ……………………………………………………………………………… 3010-1 Adjusting the seal pressure………………………………………………………………………………………………………… 30
10-2 Table switch plate actuator pressure adjustment ……………………………………………………………………………… 30
11 About the optional hot stamp printer ………………………………………………………… 31
12 Electric diagram …………………………………………………………………………………… 32
13 Common problems and solutions ……………………………………………………………… 34Exploded view and spare parts list ……………………………………………………………………………………………………… 37
FA Series Operating Instructions Ver2.01E
4
Code ModelVoltage
VPower
W
Sealing Width mm
Sealing Length mm
Weightkg
Machine Dimention mm
W x D x H
Printer Special Table
Standard Table
Table Switch-plateInner Outer
- FA-200-10 110 1150 10 200 16 260x580x360 ---
- FA-200-10W (D) 110 1450 10 200 17 260x580x360 ---
- FA-300 110 1100/520 5/2 300 16 360x580x360
- FA-300-5W (D) 110 1150 5 300 17.5 360x580x360 ---
- FA-300-10 110 1500 10 300 16.5 360x590x360
- FA-300-10W (D) 110 1500 10 300 18 360x590x360 ---
- FA-450-5 110 1200 5 450 15 520x510x360 ---
- FA-450-5W (D) 110 1350 5 450 16.5 520x380x360 --- ---
- FA-450-10 220 2200 10 450 16 520x380x370 ---
- FA-450-10W (D) 220 2200 10 450 18 520x380x370 --- ---
- FA-600-2 110 1050 2 600 19 680x370x360 --- ---
- FA-600-5 110 1500 5 600 19 680x390x360 --- ---
- FA-600-5W (D) 110 1500 5 600 21.5 680x390x360 --- --- ---
- FA-600-10 220 2700 10 600 23.5 680x380x370 --- ---
- FA-600-10W (D) 220 2700 10 600 24.5 680x380x370 --- --- ---
1 Specification
...Standard equipped ...Optional
FA Series Operating Instructions Ver2.01E
Optional special table can be mounted only when it is used along with the FA stand.
5
富士インパルス
Model Accessories
FA-200-10 Heating element/ 5pcs, Philips screwdriver, Table-switch plate (with air pedal), Seal gauge
FA-200-10W (D) Heating element/ 5pcs, Philips screwdriver, Table-switch plate (with air pedal)
FA-300 2 & 5mm-width heating element/ 5pcs each, Philips screwdriver, Seal gauge, Table-switch plate (with air pedal)
FA-300-10 Heating element/ 5pcs, Philips screwdriver, Seal gauge, Table-switch plate (with air pedal)
FA-300-5W, 10W (D) Heating element/ 5pcs, Philips screwdriver, Table-switch plate (with air pedal)
FA-450-5 Heating element/ 5pcs, Philips screwdriver, Seal gauge, Standard table, Air pedal
FA-450-10 Heating element/ 5pcs, Philips screwdriver, Seal gauge, Air pedal
FA-450-5W, 10W (D) Heating element/ 5pcs, Philips screwdriver, Air pedal
FA-600-2, 5, 10 Heating element/ 5pcs, Philips screwdriver, Air pedal, Seal gauge
FA-600-5W, 10W (D) Heating element/ 5pcs, Philips screwdriver, Air pedal
Please make sure that all of the accessories described below are included.If not, please contact your dealer.
2 Package contents
Options
These illustrations are not reduced equally.
Heating element
Philips screwdriver
Seal gauge
Table-switch plate
Standard table
Air pedal
Special table
FA stand
(Only for single side heating models.)
(Air pedal is mounted to the table-switch plate at the time of factory shipment.
(Optional product except for FA-450-5.)
FA Series Operating Instructions Ver2.01E
6
Parts Name Sales Unit
Heating element 20 pcs./set or 10 pcs./set
Teflon 2 pcs./set
Silicone rubber 2 pcs./set
Glass tape 5M or 10M roll ... 1 roll
Sarcon sheet 2 pcs./set or 5M roll ... 1 roll
Plastic nut black 6mm 5 pcs./set
Microswitch 1 pc.
Microswitch cover 1 pc.
Models Heating element Silicone rubber Teflon Glass tape Sarcon sheet
FA-200-10, FA-200-10W (D)
FA-300, FA-300-10
FA-450-5, FA-450-10
FA-600-2, FA-600-5
FA-600-10
3 pcs. 1 pc. 2 pcs. 5M roll/ 1roll 1 pc.
FA-300-5W (D), FA-300-10W (D)
FA-450-5W (D), FA-450-10W (D)
FA-600-5W (D), FA-600-10W (D)
5 pcs. 1 pc. 2 pcs. 5M roll/ 1roll 1 pc.
Routine maintenance parts, which will need to be replaced after extensive use, are sold individually as detailed below. Also the maintenance parts kits that includes all the consumable parts are available. Replacement parts can be purchased through your local Fuji Impulse dealer.
1 The impulse sealer is a machine which sends strong electric current quickly to the thin ribbon heater, which presses against the film and instantly heat seals the package. Though this machine yields superior quality sealing, it is not compatible with films thicker than that indicated in the diagram below, sponge-like sheets, and materials which are not able to withstand high heat.
2 Film thickness limits for the FA series are described below. The machine cannot seal bags which are thicker than that indicated. The machine may malfunction if you try to exceed the limits of the machine.
3 Replacement parts
4 Proper use of the sealer
Replacement parts sales unit
Maintenance parts kit detail
FA Series Operating Instructions Ver2.01E
7
Heating method Heater width Film thickness (total thickness of piled film)
Single side heating 2mm Less than 0.3mm
Single side heating 5mm Less than 0.3mm
Single side heating 10mm Less than 0.4mm
Double side heating 5, 10mm Less than 0.5mm
●Do not place your fingers near the seal surface. They may get jammed.
●The seal surface will become hot after prolonged use. Do not touch or burns may result.
●Always unplug before performing maintenance.
HOT WARNINGCAUTION
W2079
5 Warning-caution label location and contentWarning - Caution labels are placed in locations where there is a danger of injury to a person or damage to the machine. Label location details are illustrated below. Please check them before beginning operation. Labels not readily apparent are indicated by dotted lines.
This label is adhered to the bottom plate.
When opening the cover for maintenance checks, the machine must unplug from the wall outlet. Otherwise jamming or electrick shock may occure.
CAUTION
UNPLUG BEFORE PERFORMING MAINTENANCE.
Adhered on the left side of the body frame.
WARNING�electric shock
When removing the control unit, you will see this label adhered on the backside of it. Do not remove the control unit unless it is necessary.
This label is adhered on the pressure lever.
If Warning - Caution labels peel off or are lost, please purchase the proper la-bels and place them in the appropriate location.
FA Series Operating Instructions Ver2.01E
8
6 Operating precautionsFor safety operation
Warning In an emergency, unplug the power cord immediately
This sealer incorporates a number of safety devices and is carefully designed to prevent fires or other malfunctions. However, should all of the safety devices fail simultaneously, there is a possibility of the Teflon catching fire due to a failure of the heating circuit's tripping mechanism that results in the heating element overheating. Should smoke or fire appear from the Teflon, immediately release the foot pedal or turn OFF the power.
Warning Confirm proper electric power source
Make sure power source has the specified voltage and electric power as explained in “1 Specification” of this manual. DO NOT use an extension cord, as the machine may malfunction due to voltage drop or may result in fire. Machine will malfunction if connected to anything other than the specified voltage. Insert the electric power plug fully into the wall outlet.
Warning Do not use for packaging liquids
Do not splash water on the machine or use machine for packaging liquids since machine is not waterproof. There is a danger of electrocution or malfunction of the machine.
Warning Do not insert any metal objects into the sealing area
Please do not place any metal objects into the sealing area during operation. This could cause electrocution.
Warning When replacing parts, unplug the power plug
Maintenance of the machine is important. Parts should be replaced in accordance with the operating instructions. There is a risk of danger if the parts are not replaced properly. Before replacing parts, unplug the machine from the power source and replace parts referring to “Replacing the routine maintenance parts” thoroughly.
Warning Do not modify the machine
Modification of the FA series or the use of unspecified parts may not only lead to damage of the machine, but there is also a risk of danger to the operator. Please do not tamper with the machine. Accidents or damage caused by modification by the customer is the sole responsibility of the customer.
FA Series Operating Instructions Ver2.01E
9
Caution Do not use in the following places
Do not operate machine in the following places since there is a danger of malfunction:
1 Dusty locations.2 Locations not within normal temperatures.
3 Locations with high humidity.
Warning Do not use parts other than those specified
When replacing parts, always use only specified parts sold through Fuji Impulse. Not responsible for malfunctions caused by the use of unspecified parts.
Warning If the power switch automatically turns to the OFF position
If after 3 seconds heating is not complete after it has been initiated, the power switch will automatically turn OFF. There is a possibility of malfunction of the machine. Do not operate the machine until the cause of the shut down is ascertained and the problem has been addressed.
Caution Do not place hands in the sealing area
1 With prolonged use, the sealing area will retain heat and become hot. If you place your fingers in this area, there is a possibility of burns.
2 Do not place hands between the seal jaws (pressure lever and seal frame).
3 Should the foreign objects such as fingers are clamped between the sealing area and the sealer cannot move to the heating process within 0.8 seconds, the lever automatically returns to the initial position. However, the strong pressure is applied especially to the both ends to the sealing area, and there a danger that the sealing process may start without notice.
Caution Use the machine properly
Read “Proper use of the sealer” in this manual carefully and operate sealer correctly. Accidents or damage caused by misuse of the machine not in accordance with the operating instructions are the sole responsibility of the customer.
FA Series Operating Instructions Ver2.01E
10
For smooth operation
● To achieve a strong seal
Proper sealing pressure is important in achieving a strong seal. Sealing pressure for FA series can be adjusted by the power to depress the pedal. Apply the optimum pressure when sealing.
● When operating machine for extended periods of time
The machine's temperature will rise upon prolonged use of the machine. As the temperature of the machine rises, the condition of the seal will change. Thus, heating time should be shortened and cooling time should be lengthened accordingly.
● Dust in the sealing area
Dust will prevent attainment of a smooth seal. It could also cause damage to heating element and/or other routine maintenance parts. Before using the machine, clean the sealing area.
● Heating time should be set at a minimum
Set sealer so that an acceptable seal is completed in the least amount of heating time. Excessively long heating times (increasing the heat setting unnecessarily) will damage the Teflon, glass tape and other consumables, as well as result in heating element breakage. This will lead to decreased work productivity and unnecessary power consumption.
● Allow sufficient cooling time
Cooling time is important when using an impulse sealer. After the film is heated, the film must cool with the frame and pressure lever in the closed position. Take the cooling time 1.5 times longer than the heating time. For the detail, please refer to “8-7 Setting the sealing condition with the control unit”.
● When the Teflon, silicone rubber becomes damaged
The Teflon, silicone rubber will start to wear with use. Once they are damaged, it will be difficult to achieve smooth and strong seals. Thoroughly read how to replace the parts and be careful when doing so.
FA Series Operating Instructions Ver2.01E
11
Do NOT attempt to plug any other electronic devices into this outlet.
Other safeguards
The power cord from the heater section (white)
Power cord of the printer (black)
●Run test trials before beginning operation
Achieving a superior seal with an impulse sealer is determined by heating / cooling / pressure strength. Depending on the type of film being used and the contents of the bag, heating / cooling / pressure strength conditions may drastically differ. Find the optimum sealing conditions by conducting seal tests before proceeding.
● The Fuji Impulse FA series is an impulse sealer
Do not become alarmed if the sealing area does not become hot after the power switch is turned to the ON position. The machine has not malfunctioned.The Fuji impulse sealer uses an impulse method so the heating element will not become hot just by plugging the unit in or turning the power switch to the ON position. The heater will only become hot for an instant when the heating process is in operation. However, after extended periods of use, the sealing area may become hot.
● Printer outlet
The printer outlet is located on the underside of the seal frame head. It is to be used ONLY when mounting the optional printer.
FA Series Operating Instructions Ver2.01E
12
Arrows▲ and ▼increase or decrease the numeric value by one digit every time they are pushed.If you hold the button in, the numeric value will increase or decrease continuously. Use this method when making wide range changes in setting.
7 Major parts and function
Control Unit Panel
Display
Pressure adjusting nut
Pressure adjusting nut mounting screw
Pressure lever
Electrode
Plastic nut (black)
Teflon
Table switch plate
Air pedal
Body frame air switch with elbow joint
Power cord
Power switch
Control unit1. Turns on when
the power is on.2. Displays each set
value.
Adjust the seal pressure depending on the packaging material thickness.
Depress the air pedal to start operation.
1. Adjust the heating time depending on the thickness and type of film.
The greater the set value is, the longer the heating time will be.
2. Set the cooling time. The greater the set value is, the longer
the cooling time will be.3. Set the auto interval time.4. Turn ON or OFF the auto cycle interval
mode.
Push to turn ON the sealer.Push again to turn OFF.
Digital DisplayMode indicator lights
Mode selection buttonAllows for changes in the mode setting.
Numerical setting arrows
Auto cycle START/STOP
ABORT CYCLE
Counter and setting display
Setting can be increased or decreased during counter mode... COUNTER RESET
All operations are stopped and the sealer returns to the initial position.
The table switch plate can be mounted to the FA-200 and FA-300 series and can be activated by setting the air pedal.(The air pedal is set to the table-switch plate at the time of factory shipment.)
FA Series Operating Instructions Ver2.01E
13
FA series is the table-top type sealer. Place the machine on a flat, horizontal working table.The optional FA stand is available when you cannot secure the proper working place.
A Mount the table-switch plateSkip this procedure when using the air pedal as a foot switch.
1 FA-200, FA-300 Series
Fix the table-switch plate to the body frame using the wing nut. The height can be adjusted to the optimum level depending on the application. (The wing nut is installed to the bolt of the body frame where the table is installed.)
2 FA-450, FA-600 Series
The table-switch plate cannot be mounted to these sealer models. (Refer to "8-6 Select the operation mode >>> How to set each operation mode.")
B Mount the standard tableFor the FA series of sealers, the standard table will be optional parts except for FA-450-5.Fix to the seal frame using the wing nuts and bolts. The height can be adjusted to the optimum level depending on the application.
Use only as described in this manual. There is a risk of danger and malfunctions may result if the machine is used not in accordance with this manual.
8 Proper use of the sealer
8-1 Setting the machine
8-2 Mounting the table
Table-switch plate
Air pedal
Wing nut
Body frame
Wing nut
Table Seal frame
A Table-switch plate
B Standard table
FA Series Operating Instructions Ver2.01E
14
Insert the air pedal hose securely into the elbow of the main frame air switch.
C Mount the special table (Optional)The special table can be mounted to the FA stand, which is sold individually. (The air pedal cannot be installed to the special table.)
8-3 Insert the air hose
8-4 Plugging in the electrical power cord.
Special table
FA stand
C Special table
Body frame air switch with elbow joint
Air hose
Securely insert the hose
The power cord is located on the right side of the machine, when facing toward it. Make sure the electrical outlet has adequate current carrying capacity as described at “1. Specification.” Insert the electric power plug fully into the wall outlet.
Warning There is a danger of fire if the electrical power source does not meet proper specification.
FA Series Operating Instructions Ver2.01E
15
● Auto-cycle interval mode OFF (Auto cycle interval lamp OFF)
1 Air pedal operation ..... The machine operates when the air pedal is depressed.
The control unit display will turn on when the power switch, located on the side of the common frame, is pushed on.
The "Auto cycle START/STOP" button allows you to select between manual and continuous automatic operation. Turn ON or OFF the auto-cycle interval mode after selecting the operation mode referring to "8-7 Setting the sealing condition.”For the detail, refer to “8-6 Select the operation mode >>> How to set each operation mode.”
2 Table switch plate operation ..... The machine operates when the table switch plate is pushed.
● Auto-cycle interval mode ON (Auto cycle interval lamp ON)
3 Auto cycle mode ..... Automatic operation takes place based on the preset intervals.
8-5 Power switch ON
8-6 Select the operation mode
Push to turn ON
1 Air pedal operation
2 Table-switch operation
3 Auto-cycle mode
FA Series Operating Instructions Ver2.01E
16
The heating time, cooling time and auto-cycle interval can be set with the control unit.The setting values will vary depending on the pouch/film material, thickness, etc. Reset the seal conditions every time you change the bag.
Pushing the SET button changes the modes in the following order:COUNTER→HEATING TIME→COOLING TIME→AUTO CYCLE INTERVAL.The mode indicator lights show which mode is currently displayed. If no light is lit, the machine is in the counter mode.
How to set each operation mode
8-7 Setting the sealing condition with the control unit
DIGITAL DISPLAY
MODE INDICATOR LIGHTS
ALLOWS FOR CHANGEDNUMERICAL SETTING ARROWS
AUTO CYCLE START/STOP
Counter and setting display
In the mode setting Setting can be increased or decreased during counter mode... counter reset.
Operation mode FA-200, FA-300 series FA-450, FA-600 series
Air pedal operation
Push the Auto Cycle START/STOP button to turn OFF the auto cycle mode. Remove the air pedal set to the table-switch plate. Place the air pedal on the floor or the other place.
Push the Auto Cycle START/STOP button to turn OFF the auto cycle mode. Set the air pedal included in the accessories referring to "8-3 Insert the air hose".
Table-switch plate
operation
Push the Auto Cycle START/STOP button to turn OFF the auto cycle mode. Mount the table-switch plate referring to "8-2 Mount the table".
Table-switch plate operation cannot be
selected.
Auto-cycle modeSet the auto-cycle interval time. Turn ON the auco-cycle mode by pusing the Auto Cycle START/STOP button.
FA Series Operating Instructions Ver2.01E
17
Setting the auto-cycle interval
● Activate the "auto-cycle interval" mode. Use ▲/▼ arrows to set the interval. [Setting range : (set heating time x 3 times) - 5.0 sec.]
● The interval time for the auto-cycle interval mode is set 3 times longer than the heating time, and cannot be set shorter than that.
When the heating time is made longer, the control unit will automatically adjust the auto-cycle interval time if it is shorter than 3 x heating time.
Setting the heating time● Activate the "heating time" mode. Use ▲/▼
arrows to set the heating time. [Setting range : 0.1 - 1.6 sec. ]
● The optimum heating time will differ depending on the voltage when the machine is used, the thickness and type of film.
● Set the heating time at minimum to make a sufficient seal. This will increase the productivity and also prevent unnecessary power consumption.
Setting the cooling time
● Activate the "cooling time" mode. Use ▲/▼ arrows to set the cooling time. [Setting range : (set heating time) - 5.0 sec.]
● The cooling time should be set1.5 to 2 times longer than the heating time. In order to guarantee sufficient cooling time, the FA series is designed that the cooling time cannot be set shorter than the set heating time.
● When setting the heating time, the control unit will automatically correct the cooling time to the same amount as the set heating time if the heating time is set longer than the cooling time.
FA Series Operating Instructions Ver2.01E
18
Power ON
MODE DIGITAL DISPLAY
SET FIRST TIMEPUSH
PUSH SET SECOND TIME
SET THIRD TIME
RETURN TO COUNTER DISPLAY
DECREASE VALUE INCREASE VALUE
.................
.................
.................
NOTE1 .... Cooling time cannot be set less than the set heating time.
DISPLAY RANGE
NOTE1
.................NOTE2
PUSH
SET FOURTH TIMEPUSH
COUNTER VALUE
HEATING TIME
COOLING TIME
AUTO CYCLE
Set the interval time only when using the auto-cycle interval mode
NOTE2 .... Auto cycle interval cannot be set less than three times the time of set heating time.
POWER ON
MODE
DIGITAL DISPLAY
COUNTER VALUE
HEATING TIME
COOLING TIME
AUTO CYCLE
FIRST TIME
PUSH
PUSH
PUSH
PUSH
PUSH
SECOND TIME
PUSH THIRD TIME
setPUSHING FOUR TIMES WILL
RETURN YOU TO THE COUNTER MODE.
INCREMENTS OF 0.1
INCREMENTS OF 0.1
INCREMENTS OF 0.1
TO RESET THE VALUES
SETTING COMPLETE
HEATING TIME DISPLAY
COOLING TIME DISPLAY
AUTO CYCLE ITNERVAL DISPLAY
set
set
set
Setting the different modes
Example)Settings : Heating 0.8 sec. Cooling 1.2 sec. Auto cycle 2.4 sec.
FA Series Operating Instructions Ver2.01E
19
The pressure adjusting nut is adjusted to the "NORMAL" position for the film of 0.1 to 0.2 mm thickness at the time of factory shipment.The required sealing pressure varies depending on the type and thickness of the film. Adjust the sealing pressure according to each of the film to be used.
After completing the control unit and seal pressure adjustment, turn off the auto-cycle mode and manually perform the seal test to find the optimum sealing condition for your film.
8-8 Adjust the seal pressure
8-9 Perform test sealing
Pressure adjusting nut
Attention! Perform the pressure adjustment referring to “10-1 Adjusting the sealing pressure.” Change the pressure setting every time you change the film.
FA Series Operating Instructions Ver2.01E
20
1 Air pedal operationPlace a pouch to the sealing area. Depressing the air pedal will lower the pressure lever to start sealing.
2 Table-swtich plate operationPlace a pouch to the sealing area. Lightly press the part of the table-switch plate where indicated by the label to lower the pressure lever and start sealing.
3 Auto-cycle interval modeAutomatic operation takes place based on the preset intervals. Place a pouch to the sealing area according to the timing that the pressure lever descends. You can deactivate the auto-cycle mode by pushing the Auto-Cycle START/STOP button.
● ABORT CYCLE buttonTo stop the operation after the machine started working, push the “ABORT CYCLE” button. The lever will return to the initial position. The set value will not be erased even if the “ABORT CYCLE” button is pressed.
8-10 Seal with the selected operation mode
1 Air pedal operation
2 Table-switch plate operation
3 Auto-cycle mode
Caution The sealing area become hot with the prolonged use, and there is a danger of burning.
Also, it is extremely dangerous to place fingers to the sealing area where the strong pressure is applied. The machine is designed to release the pressure when the microswitch is not activated within 0.8 seconds due to the foreign objects being inserted to the sealing area. However, the strong pressure is applied especially to both ends of the sealing jaws. Please be careful as the sealer may start heating. (Especially for FA-450 and 600 series.)
FA Series Operating Instructions Ver2.01E
21
加 熱 中
冷 却 中
連続運転中
連続運転ON/OFF
中 止
加 熱 中
冷 却 中
連続運転中
連続運転ON/OFF
中 止
After the heating and cooling cycle has finished, the pressure lever returns to the initial position, and the sealing is complete. If a sealing is not clean enough, adjust the heating/ cooling time or sealing pressure.
As the sealing operation proceeds, the numeric value of the counter increases one at a time from 0000 to 9999.When you want to reset the counter to 0000, push either ▲ or ▼ arrow buttons while the machine is in the counter mode.
After finishing operation, always turn OFF the power switch.
As the set value and the seal count are retained by the control unit, there is no need to put the value every time after turning OFF the power switch.
Unplug the power outlet in the case of not using the machine for a while.
After use, please clean up the parts. Inspect parts such as Teflon and heating element to make sure that they are not damaged. If the parts appear to be damaged, replace them referring to operating instruction.
8-11 Finishing sealing
8-12 Counter reset
8-13 Power switch OFF
8-14 Inspection after operation
Push to turn OFF
FA Series Operating Instructions Ver2.01E
22
Daily maintenance or replacement of parts at an early stage can prevent the machine from being damaged, and keeps the machine at the optimum condition. Replace parts according to the following directions in order to maintain your machine in optimum operating condition.
The sealing section consists of the parts as in the illustration below. When replacing parts, be careful to arrange the parts exactly in the same order.
●Before replacing partsWhen replacing parts, lift up the pressure lever for easier replacement.
How to lift up the pressure leverTurn the pressure adjusting nut at the center of the pressure lever fully counterclockwise, and remove the pressure adjusting nut. Lift up the pressure lever. For the installment method, please refer to “10-1 Adjusting the sealing pressure >>> Attention! .”
9 Replacing the routine maintenance parts
Structure of the sealing section
9-1 Preparation
Always unplug the machine before maintenance.
Pressure leverSilicone rubber (white)
Teflon
Glass tapeSarcon sheet
Heating element
Glass tape
TeflonHeating element
Double side heating
Pressure leverSilicone rubber
Teflon
Glass tape
Sarcon sheet
Heating element
Single side heating
Pressure adjusting nut
Small lever
Pressure rubber
Pressure lever
Sliding shaft
Warning Always unplug the power plug before replacing parts. There is a danger of electrocution if it has been done without unplugging.
Warning Follow the directions on this manual when replacing parts. Replacing parts in the way ignoring this manual could cause malfunction of the machine as well as electrocution and fire.
Warning Always use only specified parts sold through Fuji Impulse. Unspecified parts may cause malfunction of the machine.
Warning When the pressure lever is lifted up, you can activate the microswitch by clicking it with a thin stick, etc. Do not activate the microswitch as it will start heating and may result in fire if the plug is not unplugged. Please refer to warning of “9-7 Replacing the microswitch.)
FA Series Operating Instructions Ver2.01E
23
Essential tools: Scissors, a Philips screwdriver
Replace when: The Tedlon burns, or when the seal becomes messy.
Teflon is either sold individually or included in the maintenance parts kit. It is rolled to the Teflon roll bar about 25 - 30cm as an extra.
Lower Teflon sheet1 Loosen two black plastic nuts at the front side of
the machine to remove the lower Teflon sheet holding plate.
2 Loosen two black plastic nuts that fix the Teflon roll bar fastening plates so the Teflon roll bar can be moved, and slide the Teflon toward you.
3 Cut the damaged part of the Teflon with scissors.4 Insert the edge of the Teflon between the lower
Teflon holding plate and Teflon sheet holder support. And then fix the lower Teflon sheet holding plate with black plastic nuts.
5 Roll up the Teflon to the Teflon roll bar so it does not get wrinkled.
6 Tighten the black plastic nuts to secure the Teflon roll bar with Teflon roll bar fastening plates.
Upper Teflon sheet (For FA-200, FA-300 double side heating
type)
1 Loosen the screws that fix the upper Teflon sheet holding plate and slid off the edge of the Teflon.
2 Loosen the screws of the Teflon sheet holding brackets so the Teflon roll bar can be moved. Slide the Teflon toward you.
3 Cut the damaged part of the Teflon with scissors.4 Insert the edge of the Teflon between the upper
Teflon sheet holding plate and pressure lever and tighten the screw loosened at procedure 1 to fix the Teflon edge.
5 Roll up the Teflon to the Teflon roll bar so it does not wrinkled.
6 Tighten the screws of the Teflon sheet holding brackets to secure the Teflon roll bar.
9-2 Sliding the Teflon sheet
Teflon roll bar fastening platePlastic nut (black)
Teflon roll bar
Teflon sheet holding plate (lower)
Slide off the Teflon sheet
Plastic nut (black)
Teflon sheet holding plate (upper) Teflon sheet
Teflon roll bar holding bracket
FA Series Operating Instructions Ver2.01E
24
Upper Teflon sheet (For FA-450, FA-600 double side heating
type)
1 Loosen the white plastic nuts at the backside of pressure lever so the Teflon roll bar can be moved.
2 Loosen the screws that fixes the upper Teflon sheet holding plate and slide off the Teflon to the direction of allow.
3 Cut the damaged part of the Teflon with scissors.4 Insert the edge of Teflon between the upper
Teflon sheet holding plate and pressure lever, and tighten the screws to fix the Teflon sheet holding plate.
5 Roll up the Teflon to the Teflon roll bar so it does not wrinkled.
6 Tighten the white plastic nuts to secure the Teflon roll bar with upper Teflon roll bar fastening plates.
Electrodes that mount the heating element consist of parts as in the right illustration.
Essential tools: A Philips screwdriver
Replace when: The heating element breaks, unevenness is generated, or when the
seal becoms messy.The heating element is either sold individually or included in the maintenance parts kit.
Warning If you loose the screw C, do not substitute ones longer than the screw C (M4x6) as there is a danger of short circuit by the longer screw touching screw D.
Warning When replacing the heating element, replace the glass tape and Sarcon sheet as well if they are appear to be damaged. If they are damaged and cannot properly insulate the heating element from the body frame, the short circuit may result.
TIPS The heating element can be replaced without removing the electrode cover so you will not loose the cover or screw.
9-3 Replacing the heating element
Teflon sheet holding plate (upper)
Teflon roll bar fastening plate (upper)
Plastic nut (white)
Teflon roll bar
Electrode mounding bracket
Electrode plate
Electrode plate spring
Electrode cover
Terminal coverScrew A
Screw C(M4x6)
Screw B
Screw D
Mounted only to the single side heating models.
FA Series Operating Instructions Ver2.01E
25
Lower heating element (for all models)
1 Remove the Teflon sheet. (Refer to “9-2 Sliding the Teflon sheet.”)
2 Loosen the screw A of both electrodes with a Philips screwdriver, and remove the terminal covers. The illustration on the right describes the electrode after the terminal cover is removed.
3 Loosen screw B of both electrodes to loosen the tension of the heating element. It is not necessary to remove the electrode covers.
4 Insert a Philips screwdriver into the hole of the electrode cover and loosen screw C. The heating element can be removed.
5 When mounting the new heating element, insert each terminal between the electrode plate and electrode plate spring. While pushing down the terminal with your fingers so it stays in place, tighten the screw C with a Philips screwdriver.
6 Tighten the screw B loosened at the procedure 3 so the heating element is stretched tight. When the screw B is not tightened enough, the heating element will not be stretched tight enough, which may result in damaging the heating element.
7 Fix the terminal covers to the electrodes with screw A.
Upper heating element (for double side heating models)
1 Remove the Teflon sheet. (Refer to “9-2 Sliding the Teflon sheet.”)
2 Loosen the screw B of both electrodes with a Philips screwdriver, and remove the terminal covers. The illustration on the right describes the electrode after the terminal cover is removed.
3 Insert a Philips screwdriver into the hole of the electrode cover and loosen screw C. The heating element can be removed.
4 When mounting a new heating element, insert each terminal between the electrode plate and electrode plate spring. While pushing down the terminal with your fingers so it stays in place, tighten screw C with a Philips screwdriver.
5 Tighten the screw B loosened at the procedure 2 so the heating element is stretched tight. When the screw B is not tightened enough, the heating element will not be stretched tight enough, which may result in damaging the heating element.
Push
Turn while pushing
Teflon sheet
Heating element terminal
Turn
Screw B
Teflon sheet
Heating element
Screw C
Electrode plate spring
Electrodeplate
Screw B
Push
Screw C
Turn while pushing
Electrode plate spring
Electrodeplate
Teflon sheet
Heating element terminal
Teflon sheet
Turn
Heating element
Caution Without loosening the screw B, the heating element will be kept stretched tight. Thus the heating element terminal cannot be inserted between the electrode plate and plate spring.
Caution Without loosening the screw B, the heating element will be kept stretched tight. Thus the heating element terminal cannot be inserted between the electrode plate and plate spring.
FA Series Operating Instructions Ver2.01E
26
Seal area length
About 5mm
About 2mm
About 5mm
About 2mm
Essential tools: Scissors, A Philips screwdriver
Replace when: The heating element breaks often, the seal becomes messy, etc.
The glass tape and Sarcon sheet are either sold individually or included in the maintenance parts kit.
1 Carefully read the respective replacement instructions on the Teflon and heating element and remove all of them.
2 Completely remove the glass tape and Sarcon sheet.
3 Cut the new Sarcon sheet 2mm longer than the seal area for left and right sides and adhere it to the lever.
4 Adhere the glass tape over the Sarcon sheet so it covers the electrode about 5mm.
Attention! Applying the Sarcon sheet and glass tape to a surface with adhesive residues will negatively affect the sealing surface.
Attention! If the adhesive of the Sarcon sheet is weak when replacing the glass tape, please replace the Sarcon sheet as well.
9-4 Replacing the glass tape and Sarcon sheet
Sarcon sheet
Glass tape
Electrode
Adhere the glass tape over the Sarcon sheet.
FA Series Operating Instructions Ver2.01E
27
3mm
Essential tools: Industrial-purpose alcohol (Ethanol)
Replace when: The seal becomes messy, etc.The silicone rubber is either sold individually or included in the maintenance parts kit.
1 Remove the damaged (old) silicone rubber.2 Using an industrial purpose alcohol, etc.,
completely remove the adhesive residues remaining on the metal portion of the pressure lever.
3 Adhere the new silicone rubber starting from the edge.
Attention! Adhere the silicone rubber carefully as it cannot be reapplied.
Essential tools: N/A
Replace when: The height of the shock absorbing clearance become lower than 2mm. (New pressure rubber has 3mm in height.)
The pressure rubber is sold individually. Please inspect the height of shock absorbing clearance periodically.Lift up the pressure lever referring to “9-1 Preparation” for the easier replacement.
9-5 Replacing the silicone rubber
9-6 Replacing the pressure rubberShock absorbing clearance for the new product
Pressure rubber cross section diagram
Silicone rubber
Pressure lever
Adhere from the edge
Warning New pressure rubber has 3mm-high shock absorbing clearance. The long-term use of the machine could cause the wear-out of the pressure rubber. If the shock absorbing clearance become lower than 2mm, sealing pressure increases and too much pressure can be applied to the sealing area. This is extremely dangerous especially when a finger is caught in the sealing area by any chance.
Inspect the pressure rubber before the operation and replace it if necessary.
FA Series Operating Instructions Ver2.01E
28
NC
NO
COM
Gray
Yellow
Gray
Gray
Warning If the wiring of the microswitch is not correct, the timer may be damaged. Regarding the triac connection, the label is adhered to the timer.
Warning If you activate the microswitch by pushing it with a thin object, it may bring the heat to the heating element and there is a danger of burning or fire.
Essential tools: A Philips screwdriver
The microswitch is sold individually.
1 Referring to “9 Replacing the routine maintenance parts >>> 9-1 Preparation,” lift up the pressure lever.
2 Loosen the screws that fix the microswitch case to the common frame, and remove the microswitch case.
3 Next, loosen the screws that fix the microswitch, and remove it from the microswitch case.
4 Remove all of the cables.
Installation5 When reattaching the microswitch, wire properly
referring to “12 Electric diagram.” If the wiring is not correct, the timer may be damaged.
Warning Always unplug the power cord from the outlet when replacing the microswitch.
6 Attach the microswitch to the microswitch case removed at the procedure 3 using the screws. Please refer to the illustration on the right for how to install to the microswitch case.
7 Attach the microswitch case to the common frame.
8 Return the pressure lever etc. removed at the procedure 1 to the initial state.
9-7 Replacing the microswitchCommon frame
Microswitch case
Microswitch case
Microswitch
Microswitch case
Microswitch
FA Series Operating Instructions Ver2.01E
29
When the thickness of a bag is 0.6mm
0.1mm~0.5m
0.1mm~0.2mm
Less than 0.1mm
NO
MA
L
0.1m /m
or less
0.6m
/m
or m
ore
To
read
just
dial
, tur
n it
fully
clo
ckw
ise,
then
turn
itba
ck to
NO
RM
AL.
NOMAL0.1 m/m
or less
0.6m /m
or more
To readjustdial, turn itfully clockwise,then turn itback to NORMAL.
NO
MA
L
0.1m/mor less
0.6m
/mor
mor
eTo
read
just
dial
, tur
n it
fully
clo
ckw
ise,
then
turn
itba
ck to
NO
RM
AL.
NOMAL0.1 m/m
or less
0.6m /m
or more
To readjustdial, turn itfully clockwise,then turn itback to NORMAL.
Adjust the pressure strength indicated on the seal pressure adjusting nut using the pointer on the small lever.
1 Loosen the pressure adjusting nut fastening screw.
2 Turn the pressure adjusting nut to adjust the sealing pressure to a level suited for the thickness of the packaging material used. Use the compatible thickness described on the pressure adjusting nut as guidance. (Turn the pressure adjusting nut fully clockwise as it stops at the pressure for less than 0.1mm, then turn counterclockwise to adjust.)
3 Once the adjustment is made, always use the securing screw to secure the pressure adjusting nut.
When the bag contents are heavy, the table switch may be turned on immediately and activate the sealer. Adjust the table pressure adjustment screw so the table does nor activate the sealer.
10 Adjusting each part10-1 Adjusting the seal pressure
10-2 Table switch plate actuator pressure adjustment
Seal pressure adjusting nut
Pressure adjusting nut
fastening screw
Pressure rubber
Shock absorbing clearance (about 3mm)
Maximum compression (about 2mm)
Table switch plate pressure adjustment screw
The pressure adjusting spring is installed inside the screw.
Seal pressure adjusting nut
Pointer
Small lever
Pressure adjusting nut fastening screw
Pointer Pointer
Warning Operating while the nut is turned excessively clockwise (the direction for handling thinner packaging material) may cause sealing failure or cause the pressure lever to remain at the lowered position due to the solenoid suction strength dropping and the microswitch not being activated. In addition, it is very dangerous due to the excessive pressure. Always operate by following the instructions in the following
Attention! and the setting within the red range described on the label on the adjusting nut.
Warning Operating while the nut is turned excessively counterclockwise (the direction for handling thicker packaging material) will increase the sound of the pressure lever movement.
Attention! What to do if you loosen the pressure adjusting nut too much. In the case you have loosened and caused to remove the pressure adjusting nut at the time of parts replacement:
Turn the pressure adjusting nut fully clockwise so that it stops at [Less than 0.1mm] scale. Then adjust the pointer on the scale for the packaging material. Normally, operation is done in the [NORMAL] position.
FA Series Operating Instructions Ver2.01E
30
EXP DATE 12.12.10MFG DATE 12.12.00
EXP DATE 12.12.10MFG DATE 12.12.00
● Optional hot stamp printer can be installed to the FA series of sealers.● Manufacturing date and lot number etc. can be printed at the same time as sealing.● There are two types for FEP-N2 series: One is inner printing type that prints below the sealing
surface, and the other is outer printing type that prints above the sealing surface.
11 About the optional hot stamp printer
You can choose either 1 or 2-line printing by changing the setting.
Inner printing Outer printing
Sealing surface
Models Inner Printer Outer Printer
FA-200-10 FEP-N2 ×
FA-200-10W (D) FEP-N2 ×
FA-300, FA-300-10 FEP-N2 FEP-OS-N2
FA-300-5W (D), FA-300-10W (D) FEP-N2 ×
FA-450-5, FA-450-10 FEP-N2 FEP-OS-N2
FA-450-5W (D), FA-450-10W (D) FEP-N2 ×
FA-600-2, FA-600-5, FA-600-10 FEP-N2 FEP-OS-N2
FA-600-5W (D), FA-600-10W (D) FEP-N2 ×
FA Series Operating Instructions Ver2.01E
31
Cooling FAN
Microswitch
DC solenoid
Heating elementElectrode
Transformar
Air pedal
Air switch
110V outletfor FEP
Control unit
COMMON
OPEN
Power cord
Power switch
Red
Red
BlackBlack
Gray
GrayBrown
Brown
Yellow
Gray
Gray
Black Black
Black
Black
Black
Black
Red
Gray
Fuseholder
15A
Double heating type
Thermister
(Blue fordouble type)
5 3
46
Gray
Red
Triac
12 Electric diagram
110V
FA Series Operating Instructions Ver2.01E
32
Refer to the exploded view and spare parts list for the electric parts.
Cooling FAN
Microswitch
DC solenoid
Heating elementElectrode
Transformer
Air pedal
Air switch
Control unit
COMMON
OPEN
Power switch
White
White
BlackBlack
White
WhiteBrown
Brown
Yellow
Red
Gray
Gray
Black Black
Black
Black
Black
Black
Red
Gray
FUSEHolder
15A
Double heating type
Thermister
(Blue fordouble type)
5 3
46
Blue
Blue
Gray
Gray
Transformarfor FEP
200V
100V
100V outletfor FEP
Gray
Earth
Green
White
Black
Triac
WhiteBlack
Green(Earth)
220V
Refer to the exploded view and spare parts list for the electric parts.
FA Series Operating Instructions Ver2.01E
33
Problems Check Solutions
The digital display does not turn ON even
after turning ON the power switch.
Does the electricity come to the outlet? Make sure the electricity flows to the outlet.
Is the power plug fully plugged in? Insert the power plug fully to the outle.
Is the power plug damaged? *Replace the power cord or power plug.
Is the fuse on the back of the control unit
blown?Replace the fuse.
When stepping on the air pedal, the
pressure lever does not descend even
when the auto cycle is OFF. (With beep
sound)
When stepping on the air pedal, does it click
from the microswitch accommodated in the
body frame air switch?
In case it does not click:
→*Replace the body frame air switch.
In case it clicks:
→*Replacement of the control unit is
necessary.
-----*Defects in the control unit are assumed.
Replacement is necessary.
When stepping on the air pedal, the
pressure lever does not lower even when
the auto cycle is OFF. (No beep sound)
-----* Defects in the control unit are assumed.
Replacement is necessary.
Is the air hose securely inserted to the body
frame air switch?
Securely insert the air hose to the elbow
joint of body frame air switch.
In case it is securely inserted:
→*Replacement of the control unit is
necessary.
Heating lamp turns on, but there is no heat
and sealing is not performed.
Is the heating element servered? Replace the heating element.
Is there bad connection between the
electrode and the heating element?
Polish the metal area where the electrode
and the heating element meet with the sand
paper.
Is the black (blue) wire from the transformer
to the electrode disconnected?
* Securely attach the black (blue) wire from
the transformer to the electrode.
-----* Defects in the triac of control unit are
assumed. Replacement is necessary.
If you are experiencing problems with the machine, please refer to the chart below.Carefully follow the directions in the operating instructions when replacing parts.Please consult your dealer or Fuji Impulse if after referring to the chart, the problem cannot be resolved. Please refer any questions regarding replacement of parts not listed in the operating instructions or adjustment of such parts to your dealer or Fuji Impulse.Items marked with an asterisk ※ in the “Solutions” column refer to the fact that these problems should be addressed by an electrician. If there are any problems, please contact your dealer or Fuji Impulse.
Warning Always unplug the power plug before replacing parts.
13 Common problems and solutions
FA Series Operating Instructions Ver2.01E
34
Problems Check Solutions
Heating element breaks easily .
Is the set heating time too long?Set the heating time at minimum required to
make a sufficient seal.
Is the cooling time too short? Allow sufficient cooling time.
Is the glass tape and/or Sarcon sheet
damaged?Replace the glass tape and/or Sarcon sheet.
Heating element is convex and liable to
break at the center.Is the electrode damaged? * Replace the electrode.
Sealing is not clean.
Have the pressure lever and seal frame
become hot?
(As the temperature of the pressure lever
and frame rises, the film may melt without
changing the heating time.)
Wait until the pressure lever and frame
being cooled off, and take enough operation
interval.
Is the Teflon sheet, glass tape, Sarcon sheet
or silicone rubber damaged?
Replace the Teflon sheet, glass tape,
Sarcon sheet or silicone rubebr.
Is the cooling time too short? Allow sufficient cooling time.
Is the pressure setting suitable for the
thickness of your pouch?Precisely adjust the sealing pressure.
Sealing finish differs on the right and left
side.
Is the surface of the silicone rubber uneven? Replace the silicone rubber.
When the pressure lever is lowered, do you
recognize the gap between the pressure lever
and seal frame?
If you do, please contact your local dealer
or Fuji Impulse as the machine needs to be
repaired.
The power switch automatically turns
OFF. -----
* The control unit may be broken. Replace
the control unit.Heating lamp continues to be ON and the
heating element and Teflon burn.
The following error numer is displayed
-----
* The microswitch may be broken. Replace
the microswitch.The following error numer is displayedThe error message appears when the
microswitch is turned OFF during the
heating process.
The following error numer is displayed
-----
After restarting the machine by turning
OFF and On the machine, set the sealing
condition again
Solutions marked with an asterisk * mark should be addressed by electrician or experts in replacing electric parts. If you have any troubles is solving the problems, please contact with your local dealer or Fuji Impulse.
FA Series Operating Instructions Ver2.01E
35
FA Series Operating Instructions Ver2.01E
36
When ordering spare parts, please consult the exploded view
diagram/spare parts list on the following pages and provide both
the part name and code number to your local dealer.
Exploded View Spare Parts list
FA Series Operating Instructions Ver2.01E
37
加 熱 時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
@7@7
6
4
7 5
ba
a
a
b
b
b
c
a
a
=
8
2
1
2
310
17
45
48
4636
37
73
25
2426
23
72
50
44
43
32
32
32
49
21
20
38
40
39
4241
3335
55
302914
13
13
19
56
61
60
51
50
53
59
58
57
66
6263
16
15
1918
17
9
FA-200-10 Exploded View G Type FA-200-10
38
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-200-10 Spare Parts List G Type FA-200-10
39
*Pressure lever complete set/ Code 24210D for single heating type consists of numbers 1 , 2 , 4 - 10 , 51 .
Parts Code No. Parts name Sales unit
1 24200 Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24299 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
9 33230B Silicone rubber 2 pcs/set
13 33031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 30181 Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 33210 Teflon sheet 1 pc.
19 a,b 33200 Teflon sheet holder support (with screw, nut) 1 pc.
20 33005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 33240 Heating element (L-shaped terminal) 20 pcs./set
59016 Heating element (L-shaped terminal) 10 pcs./set
24 33192 Teflon sheet 2 pcs/set
25 33193 Teflon sheet roll bar 2 pcs/set
26 33191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
30 421702B Terminal cover (with Screw) 2 pcs/set
32 a,b,c 30032B Common frame (S) 1 pc.
33 39141B # Microswitch 1 pc.
35 39142 # Microswitch case 1 pc.
36 30530 Tramsformer mounting frame 1 pc.
Parts Code No. Parts name Sales unit
37 ----- Transformer (with core cover) 1 pc.
38 27350 Transformer core cover 1 pc.
39 30130 Transformer cover 1 pc.
40 33131 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 ----- Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 ----- Power switch 1 pc.
46 ----- Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24291 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 ----- Solenoid set 1 set
55 ----- Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
62 24341 Table switch plate 1 set
63 24345 Table switch plate spring 2 pcs/set
66 24342 FA pedal holder (with nut) 1 pc.
a
=
加 熱 時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
6
4
7 5
b
b
c
a
1a2
8
b
a
b
229
64
65
12
21
23
45
36
37
38
39
40
46
48
4241
43
32
32
32
44
50
4955
56
56
50
51
53
61
60
58
59
6362
66
16
15
14
13
13
19
72
23
29
24
25
73
17
26
21
20
3335
1918
17
3
26
FA-200-10 Exploded View F Type FA-200-10W
40
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-200-10W (D) Spare Parts List F Type FA-200-10W
41
*Pressure lever complete set/ Code 24215D for double heating type consists of numbers 1 , 2 , 4 - 8 , 12 , 21 , 23 , 26 , 29 , 51 ,
64 , 65 .
Parts Code No. Parts name Sales unit
1 24201 Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24299 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
12 33531 Silicone rubber (white) 2 pcs/set
13 33031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 30181 Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 33210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 33200 Teflon sheet holder support (with screw, nut) 1 pc.
20 33005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 33240 Heating element (L-shaped terminal) 20 pcs./set
59016 Heating element (L-shaped terminal) 10 pcs./set
24 33192 Teflon sheet 2 pcs/set
25 33193 Teflon sheet roll bar 2 pcs/set
26 33191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
32 a,b,c 30033B Common frame (W) 1 pc.
33 39141B # Microswitch 1 pc.
35 39142 # Microswitch case 1 pc.
36 30530 Tramsformer mounting frame 1 pc.
Parts Code No. Parts name Sales unit
37 ----- Transformer (with core cover) 1 pc.
38 33355 Transformer core cover 1 pc.
39 33130 Transformer cover 1 pc.
40 33132 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 ----- Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 ----- Power switch 1 pc.
46 ----- Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24291 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 ----- Solenoid set 1 set
55 ----- Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
62 24341 Table switch plate 1 set
63 24345 Table switch plate spring 2 pcs/set
64 33215 Upper Teflon sheet holding plate (w/ screw, spring) 1 pc.
65 39497 Upper Teflon sheet holding bracket 2 pcs/set
66 24342 FA pedal holder (with nut) 1 pc.
@7
加熱時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
6
4
7 5
b
a
b
a
b
b
c
a
=
a
3
9
22
1
8
4532
32
32
48
46
49
44
50
55
17
73
2625
2423
72
21
20
1918
3533
43
36
37
40
38
39
4241
19
3029
13
13
14
15
16
56
57
61
50
51
53
59
58
60
66
6263
17
FA300 S Exploded View G Type FA-300
G Type FA-300-10
42
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-300 S Spare Parts List G Type FA-300
G Type FA-300-10
43
*Pressure lever complete set/ Code 26 for single heating type consists of numbers 1 , 2 , 4 - 9 , 51 .
Parts Code No. Parts name Sales unit
1 24300 Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24299 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
9 3 Silicone rubber 2 pcs/set
13 30031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 30181 Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 30210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 30200 Teflon sheet holder support (with screw, nut) 1 pc.
20 30005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 7 Heating element (L-shaped terminal) 20 pcs./set
Heating element (L-shaped terminal) 10 pcs./set
24 30192 Teflon sheet 2 pcs/set
25 30193 Teflon sheet roll bar 2 pcs/set
26 30191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
30 421702B Terminal cover (with Screw) 2 pcs/set
32 a,b,c 30032B Common frame (S) 1 pc.
33 39141B # Microswitch 1 pc.
35 39142 # Microswitch case 1 pc.
36 30530 Tramsformer mounting frame 1 pc.
Parts Code No. Parts name Sales unit
37 12 Transformer (with core cover) 1 pc.
38 13 Transformer core cover 1 pc.
39 14 Transformer cover 1 pc.
40 15 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 16 Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 ----- Power switch 1 pc.
46 ----- Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24291 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 ----- Solenoid set 1 set
55 ----- Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
62 24341 Table switch plate 1 set
63 24345 Table switch plate spring 2 pcs/set
66 24342 FA pedal holder (with nut) 1 pc.
Special Parts ListCode Parts Name FA-300 FA-300-10
3 Silicone rubebr 30230B 34230B
7Heating element (20pcs/set)
30247(2mm width)30246(5mm width)
34240
Heating element (10pcs/set)5902059022
59024
12 Transformer - -
13 Transformer core cover 30350 32350
14 Transformer cover 30130 27130
15 Transformer fastening screw 30131 32131
16 Powre cord - -
26 Pressure lever complete set 24301D 24302D
b
@7
加熱時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
a
b
c
a
b
=
a
8292
1
4
62
64
65
48
46
40
3739
3836
43
45
32
32
32
4142
5655
49
50
44
3335
51
50
53
57
59
58
61
60
6362
66
16
15
14
13
13
19
72
4324
25
73
26
29
3
17
26
23
21
12
21
20
191817
b
a
7 5
FA300 W (D) Exploded View F Type FA-300-5W
F Type FA-300-10W
44
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-300 W (D) Spare Parts List F Type FA-300-5W
F Type FA-300-10W
45
*Pressure lever complete set/ Code 26 for double heating type consists of numbers 1 , 2 , 4 - 8 , 12 , 21 , 23 , 26 , 29 , 51 , 64 , 65 .
Parts Code No. Parts name Sales unit
1 24304B Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24299 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
12 30511 Silicone rubber (white) 2 pcs/set
13 30031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 30181 Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 30210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 30200 Teflon sheet holder support (with screw, nut) 1 pc.
20 30005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 7 Heating element (L-shaped terminal) 20 pcs./set
24 30192 Teflon sheet 2 pcs/set
25 30193 Teflon sheet roll bar 2 pcs/set
26 30191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
32 a,b 30033B Common frame (W/D) 1 pc.
33 39141B # Microswitch 1 pc.
35 39142 # Microswitch case 1 pc.
36 30530 Tramsformer mounting frame 1 pc.
Parts Code No. Parts name Sales unit
37 12 Transformer (with core cover) 1 pc.
38 13 Transformer core cover 1 pc.
39 14 Transformer cover 1 pc.
40 15 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 16 Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 ----- Power switch 1 pc.
46 ----- Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24291 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 ----- Solenoid set 1 set
55 ----- Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
62 24341 Table switch plate 1 set
63 24345 Table switch plate spring 2 pcs/set
64 30215 Upper Teflon sheet holding plate (w/ screw, spring) 1 pc.
65 39497 Upper Teflon sheet holding bracket 2 pcs/set
66 24342 FA pedal holder (with nut) 1 pc.
Special Parts ListCode Parts Name FA-300-5D FA-300-10D
7Heating element (20pcs/set) 30246 34240
Heating element (10pcs/set) 59022 59024
12 Transformer - -
13 Transformer core cover 27350 32350
14 Transformer cover 30130 27130
15 Transformer fastening screw 30131 34131
16 Powre cord - -
26 Pressure lever complete set 24305D 24310D
FA-450-10
加 熱 時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
FA-450-10
6
4
7 5
b
a
bc
a
=
a
2
21
9
3
45
48
4636
43
39
38
40
37
41
42
42
50 44
75
4955
56
30
29
24
72
19
23
2526
4433
35
51
50
53
59
57
61
58
60
1718 19
20
21
15
14
13
13
8
32
32
32
16
73
17
@7
b
a
FA-450 S Exploded View G TypeFA-450-5
G TypeFA-450-10
46
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-450 S Spare Parts List G TypeFA-450-5
G TypeFA-450-10
47
*Pressure lever complete set/ Code 26 for single heating type consists of numbers 1 , 2 , 4 - 9 , 51 .
Parts Code No. Parts name Sales unit
1 24399 Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24599 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22067 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
9 3 Silicone rubber 2 pcs/set
13 27031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 30181 Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 27210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 27200 Teflon sheet holder support (with screw, nut) 1 pc.
20 27005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 7 Heating element (L-shaped terminal) 20 pcs./set
24 27192 Teflon sheet 2 pcs/set
25 27193 Teflon sheet roll bar 2 pcs/set
26 27191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
30 421702B Terminal cover (with Screw) 2 pcs/set
32 a,b 30032B Common frame (S) 1 pc.
33 39141B # Microswitch 1 pc.
Parts Code No. Parts name Sales unit
35 39142 # Microswitch case 1 pc.
36 11 Tramsformer mounting frame 1 pc.
37 12 Transformer (with core cover) 1 pc.
38 13 Transformer core cover 1 pc.
39 14 Transformer cover 1 pc.
40 15 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 16 Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 28 Power switch 1 pc.
46 17 Control unit 1 pc.
29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24591 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 19 Solenoid set 1 set
55 21 Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
75 53601 FEP outlet transformer 1 pc.
Special Parts ListCode Parts Name FA-450-5 FA-450-10
3 Silicone rubebr 27230B 27620B
7Heating element (20pcs/set) 27246 27610
Heating element (10pcs/set) 59038 59039
11 Tramsformer mounting frame 30530 -
12 Transformer - -
13 Transformer core cover 27350 27355
14 Transformer cover 30130 32130
15 Transformer fastening screw 30131 27132
16 Power cord - -
17 Control unit - -
19 Solenoid set - -
21 Cooling fan - -
26 Pressure lever complete set 24401D 24402D
28 Power switch - -
FA-450-10W/D
FA-450-10W/D
加 熱 時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
6
4
7 5
b
b
a
b
c
a
b
=
a
8
12
29
2
32
32
32
45
3373
67
26
44
29
4636
37
38
41
43
40
42
3948
42
44
75
49
50
5556
57
50
53
51
59
58
61
60
29
19
23
72
24
2526
13
14
13
15
16
1918
17
20
21
73
17
1221
23
64
3
a
35
FA-450 W (D) Exploded View F typeFA-450-5W
F typeFA-450-10W
48
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-450 W (D) Spare Parts List F typeFA-450-5W
F typeFA-450-10W
49
*Pressure lever complete set/ Code 26 for double heating type consists of numbers 1 , 2 , 4 - 8 , 12 , 21 , 23 , 26 , 29 , 51 , 64 , 65 .
Parts Code No. Parts name Sales unit
1 24400B Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24599 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
12 27521 Silicone rubber (white) 2 pcs/set
13 27031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 30181 Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 27210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 27200 Teflon sheet holder support (with screw, nut) 1 pc.
20 27005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 7 Heating element (L-shaped terminal) 20 pcs./set
24 27192 Teflon sheet 2 pcs/set
25 27193 Teflon sheet roll bar 2 pcs/set
26 27191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
32 a,b,c 30033B Common frame (W/D) 1 pc.
33 39141B # Microswitch 1 pc.
Parts Code No. Parts name Sales unit
35 39142 # Microswitch case 1 pc.
36 11 Tramsformer mounting frame 1 pc.
37 12 Transformer (with core cover) 1 pc.
38 13 Transformer core cover 1 pc.
39 14 Transformer cover 1 pc.
40 32132 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 16 Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 28 Power switch 1 pc.
46 17 Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24591 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 19 Solenoid set 1 set
55 21 Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
64 27215 Upper Teflon sheet holding plate (w/ screw, spring) 1 pc.
67 18115 Plastic nut (white) 5mm 5 pcs/set
75 53601 FEP outlet transformer 1 pc.
Special Parts ListCode Parts Name FA-450-5D FA-450-10D
7Heating element (20pcs/set) 27246 27610
Heating element (10pcs/set) 59038 59039
11 Tramsformer mounting frame 30530 -
12 Transformer - -
13 Transformer core cover 32350 27355
14 Transformer cover 27130 32130
16 Power cord - -
17 Control unit - -
19 Solenoid set - -
21 Cooling fan - -
26 Pressure lever complete set 24405D 24410D
28 Power switch - -
FA-600-10
FA-600-10
加 熱 時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
6
4
7 5
b
c
b
a
a
ba
3
1921
2023
1724
25
26
73
17
3029
8
72
45
68
68
68
15
50
4142
43
3335
44
42
40
39
3836
37
48
46
75
2930
13
14
4955
56
44
51
50
5361
58
59
60
57
1918
17
92
21
FA-600 S Exploded View G TypeFA-600-5
G TypeFA-600-10
G TypeFA-600-2
50
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-600 S Spare Parts List G TypeFA-600-5
G TypeFA-600-10
G TypeFA-600-2
51
*Pressure lever complete set/ Code 26 for single heating type consists of numbers 1 , 2 , 4 - 10 , 51 .
Parts Code No. Parts name Sales unit
1 24600 Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24599 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure adjustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
9 3 Silicone rubber 2 pcs/set
13 32030B Seal frame (with Teflon sheet holding screw) 1 pc.
14 24680B Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 32210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 32200 Teflon sheet holder support (with screw, nut) 1 pc.
20 32005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 7 Heating element (L-shaped terminal) 20 pcs./set
24 32192 Teflon sheet 2 pcs/set
25 32193 Teflon sheet roll bar 2 pcs/set
26 32191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
30 421702B Terminal cover (with Screw) 2 pcs/set
33 39141B # Microswitch 1 pc.
Parts Code No. Parts name Sales unit
35 39142 # Microswitch case 1 pc.
36 11 Tramsformer mounting frame 1 pc.
37 12 Transformer (with core cover) 1 pc.
38 13 Transformer core cover 1 pc.
39 14 Transformer cover 1 pc.
40 15 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 16 Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 28 Power switch 1 pc.
46 17 Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24591 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 19 Solenoid set 1 set
55 21 Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
68 a,b,c 24675B Teflon sheet center holder (w/ nut, screw, s washer, rubber) 1 set
75 53601 FEP outlet transformer 1 pc.
Special Parts List Code Parts Name FA-600-2 FA-600-5 FA-600-10
3 Silicone rubebr 32230B 32230B 32231B
7Heating element (20pcs/set) 32247 32246 38246
Heating element (10pcs/set) 59043 59045 59046
11 Tramsformer mounting frame 30530 30530 -
12 Transformer - - -
13 Transformer core cover 32351 32350 32355
14 Transformer cover 30130 27130 32130
15 Transformer fastening screw 32131 32132 32133
16 Power cord - - -
17 Control unit - - -
19 Solenoid set - - -
21 Cooling fan - - -
26 Pressure lever complete set 24601D 24601D 24602D
28 Power switch - - -
b
a
c
b
a
a
@7
b
加熱時 間冷 却 時 間運 転 間 隔 加熱中冷
却中連続運転中連続運転ON/OFF
モード切 替
中止
FA-600-10W/D
FA-600-10W/D
29
1
2
8
2
6773
26
3
721921
2023
45
73
68
681516
5014
4955
56 44
3533
75
44
57
53
50
51
61
60
1918
48
46
37
3638
39
40
43
1341
29
42
42
17
6817
172524
26
64
23
21
12
58
59
6
4
7 5
FA-600 W (D) Exploded View F TypeFA-600-5W
F TypeFA-600-10W
52
●Specify the part number and product name when ordering.
●Specify the part name if there is no part number. ● The parts with # mark are common parts with FA series.
FA-600 W (D) Spare Parts List F TypeFA-600-5W
F TypeFA-600-10W
53
*Pressure lever complete set/ Code 26 for double heating type consists of numbers 1 , 2 , 4 - 8 , 12 , 21 , 23 , 26 , 29 , 51 , 64 , 67 , 73 .
Parts Code No. Parts name Sales unit
1 24608B Pressure lever 1 pc.
2 a,b 30020 # Lever fastening bolt (w/ nut, whashers) 2 pcs/set
3 24599 Large pressure spring 1 pc.
4 24010 # Pressure adjusting nut with label 1 pc.
5 24030C # Small lever (w/ screw, spring, switch pin) 1 pc.
6 24071B # Switch pin set (w/ nut, s washer) 1 set
7 22007 # Pressure a djustment nut mounting screw 1 pc.
8 22080 # Pressure rubber 1 pc.
12 32235 Silicone rubber (white) 2 pcs/set
13 32031B Seal frame (with Teflon sheet holding screw) 1 pc.
14 24680B Teflon sheet holding screw (with lead wire hoder) 2 pcs/set
15 24040B # Thermistor 1 pc.
16 24045 # Thermistor metal fitting (with screw) 1 pc.
17 30171 # Plastic nut (black) 6mm 5 pcs/set
18 32210 Teflon sheet holding plate (lower) 1 pc.
19 a,b 32200 Teflon sheet holder support (with screw, nut) 1 pc.
20 32005 Sarcon sheet 2 pcs/set
21 39434 # Glass tape 25mm width x 5M roll 1 roll
39435 # Glass tape 25mm width x 10M roll 1 roll
23 7 Heating element (L-shaped terminal) 20 pcs./set
24 32192 Teflon sheet 2 pcs/set
25 32193 Teflon sheet roll bar 2 pcs/set
26 32191 Teflon sheet with roll bar 2 pcs/set
73 18018 # Teflon roll bar fastening plate 2 pcs/set
72 30190 # Teflon cushioning rubber 1 pc.
29 421700B # H-type electrode 2 pcs/set
33 39141B # Microswitch 1 pc.
Parts Code No. Parts name Sales unit
35 39142 # Microswitch case 1 pc.
36 11 Tramsformer mounting frame 1 pc.
37 12 Transformer (with core cover) 1 pc.
38 13 Transformer core cover 1 pc.
39 14 Transformer cover 1 pc.
40 15 Transformer fastening screw (with s-washer) 4 pcs/set
41 30275 # Seal plate (with screw) 1 pc.
42 16 Power cord (with rubber bush) 1 pc.
43 24005 # Main frame mounting bolt (with s-washer, nut) 2 pcs/set
44 39495B # Bottom cover (with outlet) 1 pc.
45 28 Power switch 1 pc.
46 17 Control unit 1 pc.
- 29115 # Fuse 1 pc.
48 30150B # Control unit mounting screw 4 pcs/set
49 24591 Body frame 1 pc.
50 24080 # Air damper (w/ holding plate) 1 pc.
51 24075B # Slide shaft (with lifter) 1 pc.
53 19 Solenoid set 1 set
55 21 Cooling fan 1 pc.
56 24091 # Cooling fan guard (w/ screw) 1 pc.
57 24100 # Body frame air switch (w/ elbow joint) 1 pc.
58 24002 # Bottom plate (w/ sponge) 1 pc.
59 24068 # Rubber feet (w/ screw) 4 pcs/set
60 24170 # Air pedal (with horse) 1 pc.
61 24171 # Air pedal horse only 1 pc.
64 32215 Upper Teflon sheet holding plate (w/ screw, spring) 1 pc.
67 18115 Plastic nut (white) 5mm 5 pcs/set
68 a,b,c 24675B Teflon sheet center holder (w/ nut, screw, s washer, rubber) 1 set
75 53601 FEP outlet transformer 1 pc.
Special Parts ListCode Parts Name FA-600-5D FA-600-10D
7Heating element (20pcs/set) 32246 38246
Heating element (10pcs/set) 59045 59046
11 Tramsformer mounting frame 30530 -
12 Transformer - -
13 Transformer core cover 32350 32355
14 Transformer cover 27130 32130
15 Transformer fastening screw 32132 32133
16 Power cord - -
17 Control unit - -
19 Solenoid set - -
21 Cooling fan - -
26 Pressure lever complete set 24605D 24606D
28 Power switch - -
Y6598 JAN 2011 2nd EditionFA Series Operating Instructions Ver2.01E