1
Read the operator`s manual carefully to operate and service your planter /fertilizer model TD correctly. This manual should be considered a permanent part of the machine and should always remain with it. Failure to do so could result in personal injury or equipment damage. This unit has been designed for small and coarse grains, no-tillage and traditional tillage and should be used within usual farming applications. Should the equipment be abused or modified to change its performance beyond the original factory specification, damages will solely be at the operator’s risk. The machine must be operated by skilled users to avoid safety hazards. The operator should get acquainted with safety rules as well as current transport laws.
Pierobon S.A. will not be responsible for breakages or damage caused by alterations or changes carried out without its previous authorization. The company reserves the right to introduce necessary changes to the equipment due to technical or commercial reasons, thus not implying any kind of obligation on its part.
To our customersBefore this machine was launched into the market, countless hours were spent resear-ching and developing this and other small grains, no-tillage, traditional tillage and fertilizing equipment. Their strong and solid construction, make them achieve maximum performan-ce on the fields.
We appreciate the confidence placed in us by considering our effort to improve the machi-ne performance. Operating this equipment in accordance with the procedures outlined in this manual is your best acknowledgement.
Thank you for choosing us.
The right is reserved to make changes at any time without notice.
FOREWORD
PIEROBON S.A.José Pierobon 865 - X2189AWM Cruz Alta
Córdoba Province - Argentina+54 3467-401136
[email protected] - www.pierobon.com.ar
2
CHAPTER ISafety InformationA) Environment care 3B) Safety alert symbol 3C) Follow safety and operating instructions 3D) Avoid injury hazards 3E) For your protection 3F) Keep riders off machine 3G) Use safety lights and warning devices 3H) Transport machinery safely 3 I) Practice safe maintenance 4J) Avoid high pressure fluid hazards 4K) Handle chemicals properly 4
CHAPTER IIGeneral specificationsA) Equipment features 5B) Parts identification 6C) Row unit 7D) Technical specifications for TD 21 models 8FILAM System 9
CHAPTER IIIAdjustmentsA) Operating guidelines 12B) Operating machine 12C) Closing seeds outlet to block operation at alternateseeding rows 13D) Speed gearboxes 14E) Openers down-pressure adjustment 15F) Useful calculator to verify seeds / fertilizer rate 16G) Seed rate chart - Model TD 21 17H) Useful calculator to verify seeds / fertilizer rate 18I) Fertilizer rate chart - Model TD 21 19J) Lucerne rate chart - Model TD 21 20K) Lucerne rate chart - Model TD 21-30 21L) Row unit adjustment 22M) Wheels 23N) Wheels position for end-wise transport 24O) Wheels position for work 24P) Safety “R” clips position in wheels locks 25Q) End-wise transport hitch 25R) Working hitch 26S) Maintenance jobs 27T) Periodical maintenance jobs, cleaning and lubrication 27U) Recommended grease and oil 30V) End-of-season maintenance 31
CHAPTER IVTroubleshooting 32
CHAPTER VPlanter work capacity 34 CHAPTER VI1- Identification plate 352- Safety decals 35
Page
TABLE OF CONTENTS
3
SAFETY INFORMATIONA) Environment careDisposing of waste is harmful to the environment.Oils, fuels, filters, batteries, etc, spilled onto the ground affect ecology.Hand in these wastes to be recycled.
B) Safety alert symbolWhen you see this symbol, be aware of potential hazard of injuries due to improper use of the equipment.
C) Follow safety and operating instructionsRead and understand all safety decals in this manual andthose on the machine.Keep decals clean and legible. Replace all damaged or missing decals.The seeder will work properly if the operator reads and understands all safety and operating procedure in this manual before doing work.Alterations or changes carried out without previous authorization could cause damage to equipment or personal injury
D) Avoid injury hazardsKeep hands, feet and clothing away from moving parts.Watch out when approaching opener disks.Be sure to service machine while it is not in motion.Keep away from transmission chains and gear sprockets.
CHAPTER I E) For your protectionTo avoid injury while working under the machine, alwaysuse hydraulic cylinders safety locks.
F) Keep riders off machineryThe implement should be operated by one person only.Riders could be injured or thrown away from machine.
G) Use safety lights and devicesSlow-moving equipment or towed implements like this one can create a hazard when driven on public roads.Prevent injuries from colliding against other vehicles.Use safety lights and devices on public roads and check that they are in good working conditions. Replace or repair them if they have been damaged or lost.In some cases, additional warning lightning and markingmay be necessary.
H) Transport machine safelyEnsure machine seed tanks are empty before transport. The tank filling of both seed and fertilizer will be carried out only at work field.Before transport, always lock opener disks in raised position and lock-up the machine lifting cylinders.Hydraulic failure can allow the machine to fall rapidly, causing injury or death.It is recommended transport speed does not exceed 20 Km/h.When towing the machine under adverse surface condi-tion, reduce speed. Extreme caution is needed since the machine has no breaks.Always observe transport instructions.
4
Follow these safety rules strictly.REMEMBER: If an accidentmay happen, it will happen.
YOUR PERSONAL SAFETYAND THAT OF YOUR MACHINE
IS YOUR OWN RESPONSIBILITY.
I) Practice safe maintenanceRefer to service procedures before doing work. Keep service area clean and dry.Never lubricate or adjust machine while it is moving. Keep hands, feet and clothing away power-driven parts while in motion.Securely lower opener disks to ground to carry out servicing.Keep all parts in good condition and properly installed.Replace worn-out parts. Remove any build-up of oil, grease or debris.Wear proper protective equipment, such as special shoes, gloves, goggles, helmet, earplugs, etc.
J) Avoid high pressure fluids hazardEscaping fluid under pressure can penetrate skin, causing serious injury.Relieve pressure before disconnecting hydraulic lines and check that all connections are tightened properly before applying pressure into the hydraulic system.Use a piece of paper or cardboard, not body parts, to check for suspected leaks in connections.If an accident occurs, see a doctor immediately.
K) Handle chemicals properlyKeep chemicals away from eyes, skin and hair. If chemi-cal gets in contact with skin, wash immediately with soap and water.Dispose of unused containers properly as well as spare treated seeds and fertilizers.Do not smoke while you are exposed to chemicals.Wear protective clothing, goggles and gloves while handling chemicals.
5
ChassisIt is built with highly resistant structural tubing, which makes a strong frame to support the other implement components (Picture 1-A). The row units are anchored onto two toolbars which are conveniently spaced for better operator transit. It also features an additional front bar for front no-tillage coulters attachment.
Work hitchIt is made of structural tubing and it can be folded (manually by means of a spring in models TD 21 x 18 rows and TD 21 x 24 rows, and hydraulically in models TD 21 x 30 rows, TD 21 x 36 rows and TD 21 x 48 rows) to a vertical position to facilitate end-wise transport (Picture
1-B).
Endwise transport hitchIt is made of structural tubing and it can be folded when the machine is working (Picture 1-C).
Lifting systemHydraulically operated by four double-acting cylinders and flow control valve in each module (Picture 1-D).
Row markersHydraulically operated and sequence valve. Marking is carried out by 14” notched disks mounted on steel hubs with adjustable double conical bearings and grease seals (Picture 1-E).
Hydraulic rocking systemIndependent from lifting system to enable load distribu-tion on all four wheels while working or transporting (Series manufactured in model TD 21x 30 rows).
Lucerne boxOptional item. Made of stamped metal sheet.
Seed boxSingle box, made of stamped metal sheet and featuring great capacity (Picture 1-F).
CAPITULO II
Picture 1
GENERAL SPECIFICATIONSThe following technical specifications and general features information are useful and simple guidelines for operator´s instruction.
A) Equipment features:
A
B
E
FG
C
H
D
6
Box for solid granular fertilizerMade of stamped metal sheet and featuring great capaci-ty. It is protected by epoxy paint in the inside and its bottom is made of stainless steel (Picture 1-G).
Hydraulic jackUsed for wheels alignment operations. (Not included in Model TD 21 x 30 rows)
Wheels Provided with four (400/60 x 15.5” - 14 PR) tires per module in models TD 21 x 18 rows; TD21 x 24 rows, TD21 x 36 rows, TD21 x 48 rows and (14 x 17.5” - 14 PR) for model TD21 x 30 rows (Picture 1-H).
Speed gearboxes 27-speed gearboxes independently operating for seeds, fertilizer and lucerne.
Drive wheelThere is one (6.00 x 16 “- 6 PR) drive wheel per module which is situated at the rear part of the equipment. It has no clutches and it is supplied with a spring floating system that allows the wheel to be always in contact with the ground while the machine is planting (Picture 2).
B) Parts identificationLeft module: (Picture 3-A) If we observe the machine from behind and work oriented, we are able to identify this module as it is situated on the left hand-side and it holds the transport hitch.
Right module: (Picture 3-B) If we observe the machine from behind and work oriented, we are able to identify this module as it is situated on the right hand-side.
Picture 2
Picture 3
Figura 3
BA
7
C) Row unitOpener disk: FILAM System opener set: conical stam-ped, centered double disk with inner blade - 15.5” Ø and 5 mm thickness (Picture 4-A).
Planting depth control is carried out by a double gauge wheel surrounded by a rubber band - semi-pneumatic, featuring a rim with metal cleaner edge - placed at the sides of the double opener disks (Picture 4-B).
The oscillating arms which support the wheels, are mounted onto a rocking structure to assure optimum ground contour following. The pins, onto which the arms pivot, are made of thermically hardened steel and are threaded into a hub which strengthens the set and make all the components completely replaceable.The seed firmer is made of synthetic flexible material: acetal resin with polyurethane. It ensures seed-ground contact and contributes to depth uniformity while planting
(Picture 4-C). Optional: a seed press wheel can be attached.Furrow closing and ridge shaping are carried out by a set of notched closing disks. Down-pressure and angle of attack can be adjusted and one of the disks can be remo-ved if required by work conditions (Picture 4-D).
All turning elements (coulters, disks and wheels) are mounted onto forged steel hubs with double adjustable conical bearings.For no-tillage planting, a 16” Ø front cutting coulter must be attached to the corresponding bar. The no-till coulter can be adjusted in height and spring pressure (Picture 4-E).
The planting unit is mounted onto the chassis with parallel arms system. Down-pressure load is transferred to the planting row by two expansion springs and can be set in two different load positions, manually adjusted through a simple device.
The unit counts on two plastic outlet tubes for seeds and fertilizer placed between the opener disks. The seeds outlet tube is placed behind the disks axles (Picture 4-F) and the fertilizer tube is in front of them (Picture 4-G).
Fertilizer meterChevron wheel-type meter, variable rate carried out by means of an independent 27-speed gearbox - featuring low and high speed options (Picture 5).
Fertilizer is placed into the trench by tubes which are independent from seed tubes.Fertlizer is deposited onto the ground in front of the seed outlet.
Seed meterChevron wheel-type meter, variable rate carried out by means of an independent 27-speed gearbox - featuring low and high speed options (Picture 6).
Lucerne (Alfalfa) meter (Optional)Straight fluted meter with fixed opening (non-displa- ceable), variable rate carried out by means of an independent 27-speed gearbox – featuring low and high speed options (Picture 7). Lucerne may drop together with seeds or independently through a specific tube situated behind the seed firmer and in front of the closing wheel.
Picture 4
Picture 5 Picture 6 Picture 7
AA B C C
G
F
D DE B
8
Speed gearboxes:Planting and fertilizing variable rates are carried out by means of independent 27-speed gearboxes – featuring low and high speed options (Pictures 8, 9, and 10).
Picture 8
Seed Box
Picture 9
Fertilizer Box
Picture 10
Lucerne Box
D) Technical specifications for TD 21 models
Row spacing
Number of modules
Number of rows 48
10,08 mWorking width
Seeds/Fertilizer meter
Lucerne (alfalfa) meter
Seeds, fertilizer and lucerne rates
Chassis/row unit link
Down force spring-loaded row unit
Opener disks
Opener disks, gauge wheels andclosing disks hubs
Gauge wheels
Seed firmer
Closing wheels
Closing wheels adjustment
Seed box capacity
Fertilizer box capacity
Work tires
Endwise transport
Net weight (approx.)
Required power (approx.)
Seed firming skid - Optional: seed press wheel
Two notched disks
Down pressure force and angle of attack
Two adjustable expansion springs
Sealed with double conical bearings - Adjustable
Two per row, with metal cleaner edge
Chevron wheel - type
Straight fluted meter
27-speed gearbox
Parallel arms system
Seeder/Planter TD 2121 cm
18
3,78 m
24
5,04 m
30 (optional 32)
6,30 m
36
7,56 m
Uno Dos
900 L
900 L
120 L
1,200 L
1,200 L
160 L
1,700 L
1,700 L
200 L
1,800 L
1,800 L
240 L
2,400 L
2,400 L
320 L
Four (400/60x15,5” 14 PR)
Four(11 L15” 10 PR)
Eight(400/60x15,5” 14 PR)
Four(14x17,5” 14 PR)
No
5,050 kg
85 - 95 hp
Yes
6,150 kg
100 - 120 hp
Yes
8,200 kg
130 - 150 hp
Yes
10,080 kg
165 - 180 hp
Yes
12,320 kg
200 - 240 hp
15.5" double disks - system
Lucerne (alfalfa) box capacity
9
This machine is equipped with an exclusive design “FILAM System”, which has been awarded “Silver Medal” to Farm Machines Innovation by Ternium Siderar.
It features disks with internal edge and metal-lipped gauge wheels. This system highly improves the traditional double-disk row units as regards functionality, durability and maintenance.
This system aims at optimizing the job performed by the gauge wheel - cleaning the opener disks, and bettering furrow bottom uniformity, as well as improving disk and semi-pneumatic rubber tire lifetime.
When working on extremely wet, clayey, stubble-covered or weedy soil, blocking may affect the proper operation of the gauge wheel. When practicing no-tillage, the density of stubble is higher, so stiff or sharp components in the soil produce fast wear on the semi-pneumatic tire and even more wear on the cleaner rubber lip, thus failing to fulfill its function.
To solve this problem, the new rim helps to keep wheel/soil contact distant from the opener disk, allowing better relief of excessive stubble or crumbled soil due to disks work.
Another innovation is the replacement of the rubber cleaner lip by a metal one which is more resistant, suffers less wear, and forms part of the gauge wheel rim, thus improving the rubber tire useful life and an even and continuous cleaning job on the disks (Pictures A and B).
On the other hand, traditional disks get in contact during a very short period of working time. As soon as they start wearing off, they separate, thus increasing flexion efforts and forming a W-shaped furrow bottom, which becomes gradually deeper (Pictures C and D).
The innovation is about:
New opener disks, conically stamped at external rim, 15.5” diameter, 5mm thickness and internal edge, where continuous contact between disks is achieved during their useful life. This contact increases resistance of the set and relieves it from flexion, producing an even furrow bottom.
Conically stamped at external rim producing less angle of attack, what diminishes forward ride resistance.
The relief angle resulting from both disks cut is conver-gent, making a narrower furrow with less crumbling soil.
Picture C
Picture D
Picture A
INNOVACIÓN
Picture B
✔ Triples useful life of all main components
in the row unit.
✔ More hectares worked with less maintenance
jobs.
✔ Even furrow bottom.
✔ Less forward ride resistance.
✔ Internal edge in disks keep them in
permanent contact.
10
Internal-edged disks and metal-lipped gauge wheel. Improved system over traditional double disk row units as regardsfunctionality, durability and maintenance.
FORGED STEEL HUB
EXTERNAL HALF RIM
SEMI-PNEUMATIC TIRECONVERGENT RELIEF
ANGLE TO DIGNARROWER
FURROWS WITH LESSCRUMBLING SOIL
HALF RIM WITH METALCLEANER EDGE TO ENABLE
DISK CLEANING,
CONICAL OPENERDISK
15.5” DIAMETER5MM THICKNESS
SUNK CENTERWITH INTERNAL HUB
3-RIMMED SEAL
STANDARD ADJUSTABLECONICAL BEARINGS
HUB COVER AND RING
The disk is anchoredto the internal side
of the hub to counteractaxial forces when working
New shape to improveperformance avoid stubble inlet and
increase tire useful lifePatent pending N°050104776
Better resistanceand durability
Highly resistant to axial load
DEPTH CONTROLSEPARATE FROM
THE DISK TO ENSURE ANEVEN PLANTING DEPTH
DECOMPACTED AREADoes not interrupt gauge
wheel operation
CONTACT AREA DISTANTFROM THE DISKCompacted area
INTERNAL EDGE,CONTINUAL CONTACT
Produces less flexion in disks,keeps the same furrow shape along
its useful life,narrower angle of attack and offers
less forward ride resistance
11
Disks are incontinualcontact.
Opener disk,sunk in the
center.
Opener disk,sunk in the
center.
Contact area.Compactedsoil area.
Decompactedsoil area.
No contactbetween disks
decreasingperformancewhen shaping
furrow andplacing seeds.
Worn lip causesgauge wheel/disk
separation.
Internal-edged disks - metal-lipped gauge wheel
Traditional system – not worn out disks – not worn out disks
Traditional system15 mm worn out disk radius 15 mm worn out disk radius
12
ADJUSTMENTS��
A) Operating guidelines1- Use tractor with the following features:
2- Work speed - 6/8 km/h.3- Clean quick attach couplings terminals before connecting to tractor. 4- Never ride backwards or turn with opener disks in contact with the ground. 5- Start moving forward before lowering opener disks.6- Handle and use chemical-treated seeds, and agrochemicals in general, as specified by manufacturer.7- Check seed and fertilizer rates.8- Check machine periodically. Whenever soil conditions determine a change in planting depth and seed covering, readjust if necessary.9- Seeds setting is determined by considering the combination of the following adjustments:
a) Depth adjustment of front no-till coulters.b) Adjustment of gauge wheels of the openers disk set.c) Openers down-pressure force.d) Ridge-shaping closing wheels down-pressure force.
B) Operating machine:1- Place the machine on level ground with enough room to move the machine from transport to work position. Moving the equipment will be very difficult, unless one, or more, wheel is oriented and locked to the direction desired to ride forward.2- Connect work hitch cylinder to tractor hydraulic system.
3- Remove pin from safety bar.4- Operate cylinder to lower hitch.5- Open out the tip found in the hitch rod to tractor and fix with its pin.6- Keep lowering machine to level with tractor drawbar and couple by locking with a pin.7- Finish closing cylinders completely, disconnect and place hoses in planter.8- Connect work hitch to tractor.9- Place machine on flat steady ground.10- Unlock all wheels.11- Keeping hydraulic system connected to tractor, raise machine to release cylinder locks.12- Remove locks from hydraulic cylinders (Picture 11-A), which can be placed at the holding tubes (Picture 12 and
Picture 13).13- Check that machine is lowering and raising according to operator´s needs.14- In working position: lower machine fully – till cylinders are operated to full stroke. Leave 1 or 2 cm of visible threading (Picture 14-A) in each cylinder.15- Place front wheels in work position and lock them up.16- Before loading the box with seeds or fertilizer, adjust opener disks depth and furrow closing.17- Fill boxes with seeds or fertilizer, accordingly.18- Select gearboxes speed according to chosen applica-tion rates.
CHAPTER III
Features
Minimum power required (approx.) PTO
Hydraulic circuit minimum flow-consideringaverage revolutions at work
Hydraulic circuit pressure(maximum accepted)
Models
150 - 170 bars.
55 liters/minute
TD21-18 TD21-30TD21-24 TD21-36 TD21-4885 - 95 hp 100 - 120 hp 130 - 150 hp 165 - 180 hp 200 - 240 hp
For a proper planter operation,always operate hydraulic cylindersat full strokes, either when lowering
or raising the machine.
WARNING
WARNINGWHEN ATTACHING SEEDER TO TRACTOR
Tractor should be in oblique angle to seeder to favorunlocked wheelsalignment.
13
C) Closing seeds outlet to block operation at alternate seeding rows:• Be sure to cover the seeds outlets which correspond to the seeding rows you want to block for operation (Picture
15-A) .
• Remember to remove the star at the ejecting system from the blocked outlets.• The fertilizer box outlets matching the blocked seeds outlets must also be closed (Picture 16-A).
To block row units, proceed as follows: the row units, which are not going to be used, will be lifted onto a espe-cially designed plate for the machine (Picture 17-A).
Keep the machine on even, steady ground and proceed as follows:
a) Set the springs in all units in the position with the least down pressure (backwards).b) Lift front coulters to top.c) Thread lifting hydraulic cylinders stop-ends fully.d) Lower planter completely (till cylinders stop-ends).e) Place the especial plate between the upper parallel arm and the supporting arm of the unit that will be kept in raised position.
Pic
ture
12
Pic
ture
13
Pic
ture
15
Pic
ture
16 Pic
ture
17
Pic
ture
14
Pic
ture
11
A
A
A
A
A
14
In this way, the row units that are not going to be used and the planter configuration are as follows:
D) Speed gearboxes:To vary planting, fertilizing and lucerne rates, the machine counts on independent gearboxes, which are operated in the same way (Picture 18).
To shift gears proceed as follows:
* Keep the machine raised and still. Make the drive wheelturn while you move the levers towards the desired position till they are placed over the line marked below the corresponding letter or numeral.
* Shift gears smoothly, do not hit levers.
* The 27 speeds are the result of the combination of eachlever position according to the rates chart. It also counts on LOW and HIGH gears options.
The speed-gearboxes, if front viewed, have three levers with three positions each which are identified in the following way:
The seeds and fertilizer dischargeoutlets that are blocked,
must correspond to the raisedrow units.
I I I I I I
LEFT CENTER RIGHT
Roman numerals Letters Arabic numerals
1 2 3A B C
Pic
ture
18
Seeds gearbox Fertilizer gearbox Lucerne gearbox
MODELTD 21 X 18 rows (one module)
TD 21 X 24 rows (one module)
TD 21 x 30 rows (one module)
TD 21 x 36 rows (two modules)
TD 21 x 48 rows (two modules)
NUMBEROF ROWS
9
12
15
18
24
ROW SPACING42 cm
42 cm
42 cm
42 cm
42 cm
LOCKING ROW UNITSWARNING
1)
15
E) Openers down-pressure adjustment1) Adjustment of openers down-force load is achieved by a rocking arm with two possible load positions.
Maximum down-force load: frontwards (Picture 19-A)Minimum down-force load: backwards (A socket wrench should be used to carry out the change) (Picture 20).
Too much down-force load may increase partswear and drive resistance.
Pic
ture
19
Pic
ture
21
Pic
ture
20
SEEDS RATE FERTILIZER RATE LUCERNE RATE
Examples:
To obtain speed 20- LOW,set handles in the following way:
Then, check that the driven sprocketin the countershaft is
the 40-tooth sprocket (z40).
To obtain speed 20- HIGHthe driven sprocket
in the countershaft is the26-tooth sprocket (z26).
To obtain speed 20- LOW,set handles in the following way:
To obtain speed 20- LOW,set handles in the following way:
LEFT III
CENTER A
RIGHT 2
Then, check that the driven sprocketin the countershaft is
the 40-tooth sprocket (z40).
To obtain speed 20- HIGHthe driven sprocket
in the countershaft is the20-tooth sprocket (z20).
LEFT III
CENTER A
RIGHT 2
Then, check that theoutput gearbox sprocket is the
12-tooth sprocket.
To obtain speed 20- HIGHthe driven sprocket
in the countershaft is the19-tooth sprocket (z19).
LEFT III
CENTER A
RIGHT 2
Minimum down-force Maximum down-force
A
A
WARNING
1)
16
F)
I-722
6 (D
)
USE
FUL
CA
LCU
LATO
R T
O V
ERIF
Y SE
ED /F
ERTI
LIZE
R R
ATES
The
info
rmat
ion
on s
eedi
ng/ f
ertil
izin
g ra
tes
show
n in
the
char
t are
app
roxi
mat
e va
lues
and
may
var
y du
e to
hec
tolit
rical
wei
ght a
nd s
ize
of th
e di
ffere
nt p
rodu
cts,
that
is w
hy w
e re
com
men
d do
ing
the
follo
win
g tri
al:
1. F
ill in
box
with
see
ds o
r fer
tiliz
er, a
ccor
ding
ly.
2. P
lace
sm
all b
ags
at 2
met
ers.
3. D
epen
ding
on
row
dis
tanc
e:
4- W
eigh
bot
h sa
mpl
es to
geth
er a
nd d
ivid
e th
is a
mou
nt (i
n gr
ams)
by
two.
RO
W D
ISTA
NC
E: 1
9, 2
1, 3
8, 4
2 cm
SE
ED
ER
SM
D -
TD
The
resu
lt ob
tain
ed in
gra
ms,
will
be
dire
ctly
the
kg/h
a th
e se
eder
is a
pply
ing
whi
le ri
ding
forw
ard
durin
g th
e tri
al(p
refe
rabl
y N
° 15
)
NO
TE: i
f the
tria
l is
done
in s
peed
shi
ft N
° 15
, div
ide
the
kg/h
a yo
u w
ant t
o us
e by
the
resu
lting
am
ount
got
from
the
trial
,th
is w
ill g
ive
you
the
gear
ratio
to b
e us
ed.
or w
hile
mac
hine
is
wor
king
, rid
e fo
rwar
d
or w
hile
mac
hine
is
wor
king
, rid
e fo
rwar
d
or w
hile
mac
hine
is
wor
king
, rid
e fo
rwar
d
or w
hile
mac
hine
is
wor
king
, rid
e fo
rwar
d
24 21.5
12 10.8
mak
e dr
ive
whe
el tu
rn
mak
e dr
ive
whe
el tu
rn
mak
e dr
ive
whe
el tu
rn
mak
e dr
ive
whe
el tu
rn
times
times
times
times
52.6
47.6
26.3
23.8
m m m m
Row
spa
cing
Row
spa
cing
Row
spa
cing
Row
spa
cing
19 21 38 42
cm cm cm cm
17
G)
Kg/
ha
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
27G
EA
R R
ATIO
SPEE
D G
EAR
N°
0.45
0.48
0.50
0.53
0.56
0.60
0.63
0.67
0.70
0.75
0.80
0.84
0.89
0.94
1.00
1.06
1.12
1.19
1.25
1.32
1.41
1.48
1.57
1.66
1.76
1.87
1.97
I-725
3 (B
)
22 72 14 47 14 47 9 30 11 39 8 25 23 78 15 51 20 66 13 43 20 67 13 44 14
23 77 15 50 15 50 10 32 12 41 8 27 25 83 16 54 21 70 13 46 22 72 14 47 15
24 81 16 52 16 52 10 34 13 43 9 28 26 87 17 57 22 73 14 47 23 75 15 49 16
25 85 17 55 16 55 11 36 13 46 9 30 28 92 18 60 23 77 15 50 24 79 15 51 16
27 90 17 59 17 58 11 38 14 48 10 31 29 97 19 63 25 82 16 53 25 83 16 54 17
Z26
Z26
Z40
Z40
Z26
Z26
Z40
Z40
Z26
Z26
Z40
Z40
Z26
Z26
Z40
Z40
Z26
Z26
Z40
Z40
Z26
Z26
Z40
Z40
Z40
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
Z14
Z47
RYE
BA
RLE
Y
OAT
S
WH
EAT
SOYB
EAN
SOR
GH
UM
MIL
LET
29 97 19 63 19 62 12 41 15 52 10 34 31 104
20 68 26 88 17 57 27 89 17 58 19
30 101
20 66 20 66 13 43 16 54 11 35 33 109
21 71 28 92 18 60 28 94 18 61 20
32 108
21 70 21 70 14 45 17 58 11 37 35 116
23 76 29 98 19 64 30 100
19 65 21
34 113
22 73 22 73 14 47 18 60 12 39 36 121
24 79 31 102
20 66 32 104
20 68 22
36 121
23 78 23 78 15 51 19 65 13 42 39 130
25 85 33 110
21 71 34 112
22 73 23
38 129
25 84 25 83 16 54 20 69 14 45 42 138
27 90 35 117
22 76 36 119
23 78 25
40 135
26 88 26 87 17 57 21 72 14 47 44 145
28 95 37 123
24 80 38 125
24 81 26
43 143
28 93 28 93 18 60 22 77 15 50 46 154
30 101
39 130
25 84 40 133
26 86 28
45 151
29 98 29 98 19 64 24 81 16 53 49 163
32 106
41 137
26 89 42 140
27 91 29
48 161
31 105
31 104
20 68 25 86 17 56 52 173
34 113
44 146
28 95 45 149
29 97 31
51 171
33 111
33 110
21 72 27 91 18 59 55 183
36 120
47 155
30 101
48 158
31 103
33
54 180
35 117
35 116
23 76 28 96 19 63 58 194
38 127
49 164
31 106
50 167
32 109
35
57 192
37 125
37 124
24 80 30 102
20 67 62 206
40 134
52 174
33 113
54 177
35 115
37
60 201
39 131
39 130
25 85 31 108
21 70 65 216
42 141
55 183
35 119
56 186
36 121
39
63 213
41 138
41 137
27 89 33 114
22 74 69 228
45 149
58 193
37 125
59 197
38 128
41
68 227
44 148
44 147
28 95 35 121
24 79 73 244
48 159
62 206
39 134
63 210
41 137
44
71 238
46 155
46 154
30 100
37 127
25 83 77 256
50 167
65 216
41 140
67 221
43 144
46
75 253
49 164
49 163
32 106
39 135
27 88 82 272
53 177
69 229
44 149
71 234
46 152
49
80 267
52 174
51 173
33 112
42 143
28 93 86 287
56 188
73 242
46 158
75 247
48 161
51
84 283
55 184
55 183
35 119
44 151
30 98 92 304
59 199
77 257
49 167
79 262
51 171
55
90 301
58 196
58 194
38 126
47 161
32 105
97 324
63 211
82 273
52 177
84 279
54 181
58
94 317
61 206
61 205
40 133
49 169
33 110
102
341
67 223
87 288
55 187
89 294
57 191
61
SEED
S –
CH
EVR
ON
WH
EEL-
TYPE
MET
ER
DR
IVE
GEA
RSP
RO
CK
ETID
LER
GEA
RSP
ROCK
ET
See
der:M
D 2
1 - T
D 2
1
Info
rmat
ion
in s
eedi
ng ra
te c
hart
is a
ppro
xim
ate
and
may
var
y du
e to
hec
tolit
rical
wei
ght,
seed
s hu
mid
ity a
nd s
ize.
RO
W S
PAC
ING
: 21C
M
18
H)
19
I)
To s
hift
gear
s ke
ep th
e m
achi
ne ra
ised
and
stil
l.M
ake
the
driv
e w
heel
turn
forw
ards
and
bac
kwar
ds w
hile
you
mov
e th
e le
vers
tow
ards
the
desi
red
posi
tion
till t
hey
are
plac
ed o
ver t
he li
ne m
arke
d be
low
the
corr
espo
ndin
g le
tter o
r num
eral
.
LEVE
RS
POSI
TIO
N IN
GEA
RB
OXE
S
SPEE
D G
EAR
NU
MB
ERS
IA1
IA2
IA3
IB1
IB2
IB3
IC1
IC2
IC3
IIA
1 I
IA2
IIA
3 I
IB1
IIB
2 I
IB3
IIC
1 I
IC2
IIC
3 I
IIA1
IIIA
2 I
IIA3
IIIB
1 I
IIB2
IIIB
3 I
IIC1
IIIC
2 I
IIC3
1
2 3
4
5
6
7
8
9
10
11
1
2 1
3
14
15
16
17
18
19
2
0
21
22
23
2
4
25
26
27
Kg/
haR
OW
SPA
CIN
G: 2
1 cm
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
27G
EA
R R
ATIO
SPEE
D G
EAR
N°
0.45
0.48
0.50
0.53
0.56
0.60
0.63
0.67
0.70
0.75
0.80
0.84
0.89
0.94
1.00
1.06
1.12
1.19
1.25
1.32
1.41
1.48
1.57
1.66
1.76
1.87
1.97
See
der:M
D 2
1 - T
D 2
1 W
EIGH
T/HA
FER
TILI
ZER
GEAR
SPR
OCKE
T
FER
TILI
ZER
I-344
0 (B
)LO
W: c
ount
ersh
aft s
proc
ket:
40 te
eth
-
HIG
H: c
ount
ersh
aft s
proc
ket:
20 te
eth.
In
form
atio
n in
ferti
lizer
rate
cha
rt is
app
roxi
mat
e an
d m
ay v
ary
due
to h
ecto
litric
al w
eigh
t, se
eds
hum
idity
and
siz
e.
LO
W Z
40
HIG
H Z
20
LO
W Z
40
HIG
H Z
20
LO
W Z
40
HIG
H Z
20
75 100
112
MO
NO
-A
MM
ON
IUM
PHO
SPH
ATE
(MA
P)
DIA
MM
ON
IUM
PHO
SPH
ATE
(DA
P)
UR
EA62 96 82 12
5
92 141
58 90 77 117
86 132
55 85 73 111
81 125
52 81 69 106
77 119
49 76 65 100
73 112
47 72 61 94 69 106
44 68 58 89 65 100
41 64 55 84 61 94
39 61 52 79 58 89
37 57 49 75 55 84
35 54 46 71 52 80
33 51 44 67 49 75
31 48 41 62 46 70
29 46 39 60 44 67
28 43 37 56 41 63
26 41 35 53 39 60
25 38 32 50 36 56
23 36 31 47 34 53
22 34 29 45 33 50
21 33 28 43 31 48
20 31 26 40 29 45
65 101
86 132
96 148
69 107
91 140
102
157
73 113
96 148
108
166
77 120
102
157
114
176
82 127
108
166
122
187
87 134
114
175
128
197
20
J)
To s
hift
gear
s ke
ep th
e m
achi
ne ra
ised
and
stil
l.M
ake
the
driv
e w
heel
turn
forw
ards
and
bac
kwar
ds w
hile
you
mov
e th
e le
vers
tow
ards
the
desi
red
posi
tion
till t
hey
are
plac
ed o
ver t
he li
ne m
arke
d be
low
the
corr
espo
ndin
g le
tter o
r num
eral
.
LEVE
RS
POSI
TIO
N IN
GEA
RB
OXE
S
SPEE
D G
EAR
NU
MB
ERS
IA1
IA2
IA3
IB1
IB2
IB3
IC1
IC2
IC3
IIA
1 I
IA2
IIA
3 I
IB1
IIB
2 I
IB3
IIC
1 I
IC2
IIC
3 I
IIA1
IIIA
2 I
IIA3
IIIB
1 I
IIB2
IIIB
3 I
IIC1
IIIC
2 I
IIC3
1
2 3
4
5
6
7
8
9
10
11
1
2 1
3
14
15
16
17
18
19
2
0
21
22
23
2
4
25
26
27
6.9
12.0
6.5
11.2
6.1
10.6
5.8
10.1
5.5
9.5
5.2
9.0
4.9
8.5
4.6
8.0
4.4
7.6
4.1
7.1
3.9
6.8
3.7
6.4
3.4
6.0
3.3
5.7
3.1
5.4
2.9
5.1
2.7
4.8
2.6
4.5
2.5
4.3
2.4
4.1
2.2
3.8
7.3
12.6
7.7
13.3
8.1
14.1
8.6
15.0
9.2
15.9
9.7
16.7
5.7
9.1
5.4
8.5
5.1
8.1
4.8
7.6
4.5
7.2
4.3
6.8
4.1
6.5
3.8
6.1
9.1
14.4
8.5
13.6
8.0
12.7
7.6
12.1
7.2
11.4
6.8
10.8
6.4
10.2
6.0
9.5
12.0
19.1
11.3
17.9
10.7
16.9
10.2
16.1
9.6
15.2
12.6
20.1
13.4
21.3
14.2
22.5
15.0
23.8
16.0
25.3
16.8
26.7
Kg/
haR
OW
SPA
CIN
G: 2
1 cm
12
34
56
78
910
1112
1314
1516
1718
1920
2122
2324
2526
27 G
EA
R R
ATIO
SPEE
D G
EAR
N°
0.45
0.48
0.50
0.53
0.56
0.60
0.63
0.67
0.70
0.75
0.80
0.84
0.89
0.94
1.00
1.06
1.12
1.19
1.25
1.32
1.41
1.48
1.57
1.66
1.76
1.87
1.97
See
der:M
D 2
1 - T
D 2
1E
WE
IGH
T/H
AG
EA
R S
PR
OC
KE
TS
LUC
ERN
E (A
LFA
LFA
)
I-344
4 (C
)
LOW
Z35
LOW
Z22
HIG
H Z
35
HIG
H Z
22
LUCERNE
78
LO
W: o
utpu
t gea
r spr
ocke
t: 12
teet
h -
H
IGH
: out
put g
ear s
proc
ket:
19 te
eth.
In
form
atio
n in
see
ding
rate
cha
rt is
app
roxi
mat
e an
d m
ay v
ary
due
to h
ecto
litric
al w
eigh
t, se
eds
hum
idity
and
siz
e.
21
K)
To s
hift
gear
s ke
ep th
e m
achi
ne ra
ised
and
stil
l.M
ake
the
driv
e w
heel
turn
forw
ards
and
bac
kwar
ds w
hile
you
mov
e th
e le
vers
tow
ards
the
desi
red
posi
tion
till t
hey
are
plac
ed o
ver t
he li
ne m
arke
d be
low
the
corr
espo
ndin
g le
tter o
r num
eral
.
LEVE
RS
POSI
TIO
N IN
GEA
RB
OXE
S
SPEE
D G
EAR
NU
MB
ERS
IA1
IA2
IA3
IB1
IB2
IB3
IC1
IC2
IC3
IIA
1 I
IA2
IIA
3 I
IB1
IIB
2 I
IB3
IIC
1 I
IC2
IIC
3 I
IIA1
IIIA
2 I
IIA3
IIIB
1 I
IIB2
IIIB
3 I
IIC1
IIIC
2 I
IIC3
1
2 3
4
5
6
7
8
9
10
11
1
2 1
3
14
15
16
17
18
19
2
0
21
22
23
2
4
25
26
27
22
L) Row unit adjustment
1) Depth adjustment of the front no-till coulter is done by removing the pin and matching the hole in the vertical bar to the one in the main supporting bar at the desired depth and setting the pin back (Picture 22-A).
2) Individual adjustment is done by means of a threaded crank (Picture 23-A) placed at the rear part of the openers set. The cranks have a reference guide mark which repre-sent approximately 1 cm variation.
3) Closing wheels down-force adjustment is carried out by a handle (picture 23-B) which can be positioned into different slots (picture 23-C) to increase or decrease downpressure. These closing wheels also count on a lever used to change their angle of attack to modify the closing ridge features (Picture 23-D).
M) Row markers adjustment:
Pic
ture
22
Pic
ture
23
To carry out this operation, machine must be in raised
position.
Place locks in all hydrauliccylinders before repairing
or adjusting openers(Picture 2-Page 1).
If the hydraulic systemfails while someone
is under the machine,openers will fall rapidly, causing serious injuries
or death.
Verify adjustment once themachine has run some metersforward with openers touching
the ground in work positionand lowered row marker.
A
A
D
B
C
WARNINGWARNING
WARNING
23
• To get these distances, adjust markers by loosening the bolts at U-bolts (Picture 26-A) by sliding the tube in/outwards. When the required distance is obtained, fasten bolts (Picture 26-B).
• To mark a deeper or shallower line, adjust the marker disk angle (Picture 26-B).
M) WheelsTD Planters have their wheels mounted on self-oriented forks with a conical bearing on the base to facilitate rotation and its corresponding o-ring to seal.
1) Placed in work position (Picture 27)
2) Placed in transport position (Picture 28).
TD Seeders models chart
Important: Always measure from the last row unit to the marker disk.
When changing wheels position use the hydraulic jack supplied with
the machine.
A
A
MODEL
TD 21 x 18
TD 21 x 24
TD 21 x 30
TD 21 x 36
TD 21 x 48
NUMBER OF MODULES
One
One
One
Two
Two
NUMBER OF ROWS
18
24
30
36
48
SPACING
210
210
210
210
210
(A) DIST. (MM)
1995
2625
3255
3885
5145
Picture 24
Picture 25
Picture 26
Picture 28Picture 27
AB
WARNING
24
N) Wheels position for end-wise transport(TD 21 One Module): To transport machine properly, the wheels placed next to the transport hitch (A and B) must be unlocked, while the rear wheels must be locked (C and D) (Picture 29).
O) Wheels position for workTD 21 (one module): wheels placed next to working hitch (A and C) must remain locked, while the rear wheels (B and D) must be unlocked (Picture 31).
TD 21 (two lateral tandem modules): In this case, wheels (A, B, C, D, G and H) must remain unlocked, while wheels (E and F) must be locked (Picture 30). In rough or sloped surfaces wheels (G and H) can also be locked to improve machine transit.
TD 21 (two lateral tandem modules): wheels placed next to working hitch (A, C, E, G) must remain locked, while the rear wheels (B, D, F, H) must be unlocked (Picture
32).
AC
B D
A C GE
B D HFPicture 30Picture 29
C
B D
A A C GE
B D HFPicture 32Picture 31
25
P) Safety “r” clips position in wheels locksKeeping wheels locked either in working or transport position, with locks rods in their housing (fork bottom), “R” clip should be placed at lower part as a safety device (Picture 33).
In wheels that remain unlocked in transport position, “R”
clip will be placed at upper part of the rod (Picture 34).
In this way, the ball found at the rod end will perform as a stop onto the conical housing placed at the fork bottom.Because of the effect of the inner spring, if the wheel turns, it will get unlocked and then locked again automati-cally to avoid a sudden zigzag of the wheel.
Q) End-wise transport hitchEnd-wise transport is carried out by means of a hitch (Picture 35) located on one of the sides, by using the same wheels as in working position since they are self-oriented.
This hitch is easily folded when the machine changes into working position (Picture 36).
Pic
ture
33
Pic
ture
34
Pic
ture
35
Pic
ture
36
CAUTION CAUTIONDRIVE WHEEL TIRE INFLATION
PRESSUREMinimum: 48 lbs/inches2
Maximum: 58 lbs/inches2
Minimum: 45 lbs/inches2
Maximum: 52 lbs/inches2
INFLATION PRESSUREFOR 11L15/400-60X15,5
TIRES
26
R) Working hitchTD21 (one-module machine): one-module machines have a single hitch that can be folded upwards manually in a practical way. It is assisted by a spring and can be operated by only one person (Picture 37).
TD21 (two-module machines): two-module machines have a strengthened hitch that can be folded upwards hydraulically by means of a cylinder. (Also included in model TD 21 x 30 rows, one module) (Picture 38)
To start work, proceed as follows:
1) Connect the cylinder to the tractor hydraulic system.2) Remove safety pin.3) Operate to lower hitch.4) Unfold the tip in the hitch joint in the link to tractor and fix with its pin.5) Keep on lowering till the hitch is at the same level as the tractor drawbar.6) Close cylinder completely, disconnect hoses and leave them in the planter.7) Release the automatic locks in the hitch beams and start pulling the machine with the tractor till the locks get into their housings.8) Put safety pins in both beams.
Place the machine on levelground with enough room to move
the machine from transportto work position.
A planter out of control,may cause injury to the
operator or others.
To be able to move the machine,at least one wheel must be locked
and aligned towards thedesired moving direction.
After connecting the machineto the tractor drawbar,
close hitch operating cylindercompletely and disconnect hoses.
Pic
ture
37
Picture 38
Before folding the strengthenedhitch, beams should
be disconnected(as indicated in decals)
IMPORTANT: for transport, all aboveprocedures must be carried
out in the opposite way
WARNING WARNING
WARNINGWARNING
27
Pic
ture
40
Picture 39
Pic
ture
41
S) Maintenance Jobs1) Adjusting front cutting coulter side gap:a) Remove the cutting coulter by taking out the central bolt. b) Remove the hub cover, (Picture 39-A), take out the conical bearing (Picture 39-B) and proceed to remove all shim washers necessary till the set rotates freely (Picture 39-C). Shim washers for adjustment, can be placed in any of the bearings.
a) Remove gauge wheel and its arm by taking out the adjusting bolt (Picture 40-A).
b) Remove safety ring (Picture 41-A) and plastic cover (Picture 41-B) from opener disk hub.
c) Remove central bolt (Picture 41-C), guide bushing (Picture41-D), bearing (Picture 41-E), and shim washers till the set rotates freely (Picture 41-F).
d) Reassemble, reset cover, safety ring, clean and seal, if possible, with textured water paint.
e) Replacing opener disks: Diameter of an opener disk is 15.5”. Replace disk if its diameter is 13.5” due to disk wear.
T) Periodical maintenance jobs, cleaning and lubrication1) Preventive maintenance jobs to carry out after 20 and 100 operation hours:After the first 8 hours´operation, proceed to tighten all the bolts in the machine, mainly those found at:a) Bearing housings in parallel arms shafts (wheels support).b) Supporting brackets in work hitch and chassis crossbeams.c) Supporting brackets in transport hitch linkage.
d) Row markers seat and supporting brackets.e) Supporting anchorage of drive wheel set.f) Bearing housings in pivot shafts of drive wheel set.g) Bolts in wheels hubs.h) Seed box/ chassis linking bolts.i) Gearboxes fixing bolts.j) Bolts in row unit.k) Bolts in wheels locks.REPEAT THIS PROCEDURE AFTER 100 HOURS´ OPERATION
These adjustments are carriedout in the same way in gauge
wheels hubs and closingwheels hubs.
IN OPENER DISKS HUBS ONLYImportant: when you do this
adjustment, the hub central bolt onthe RIGHT SIDE is RIGHT-HAND
THREADING and the one onthe LEFT SIDE is LEFT-HAND
THREADING(looking at the machine from behind).
2) Adjusting Opener disks hubs with bearings.
B C
A
A
A
BD
C
E
F
WARNING
WARNING
28
2) Cleaning seeds and fertilizer boxes:
3) Lubrication chart:
At the end of the seeding season and with the machine still on the field, seed and fertilizer boxes should be cleaned following these steps:
• Open discharge outlets and drop all seeds and fertilizerto ground.
• Sweep remaining seed and fertilizer towards discharge outlets.
• Make drive wheel turn to remove all the seeds and fertilizer housed in meters.
• Check that there are no remaining seeds or fertilizer in boxes,meters and discharge tubes.Then proceed to block all discharge outlets in the boxes.
To avoid metal getting rusty andmeters getting clogged, remove
seeds (especially if they have beenchemically treated) and fertilizer
completely before storingthe machine.
Understand all procedures before doing maintenance jobs.
Never lubricate, adjust or repair machine while it is in motion.
Keep hands, feet and clothing away from moving parts.
1 x wheel Drive wheel shaft tube 50 42-A
1 x wheel Drive wheel pressure rod 30 43-A
1 x row marker Base bushings in markers cylinders 30 44-A
1 x row marker Bushings in markers support pin 30 44-B
2 x wheel Transport and work wheels pivot 30 45-A
1 x wheel Bushings for wheels vertical locking pins 150 45-B
2 x hitch Work hitch hinge pin (TD30) 100 46-A
4 x hitch Bushings in transport hitch hinge 100 47-A
2 x cylinder Bushings in hydraulic rocking system cylinder 50 48-A
1 x machine Joints at modules linkages – lateral tandem 150 49-A
1 x machine Joint and hinge pin in module linkages – lateral tandem 150 50-A
1 x row unit Gauge wheels arms end – rocker 35 51-A
2 x row unit Bushings in gauge wheels arms 25 51-B
4 x arm Parallel arm shaft - wheel support 30 52-A
2 x arm Cylinder axles – wheels support 30 52-B
1 x drive Bushing in square center drive shaft - lucerne box 50 53-A
2 x box Lucerne box drive shaft 50 54-A
WARNING
WARNING
NUMBER OFGREASE FITTINGS LOCATION
LUBRICATION INTERVAL(EXPRESSED IN HOURS) PICTURE
29
Pic
ture
42
Pic
ture
43
Pic
ture
44
Pic
ture
45
Pic
ture
46
Pic
ture
47
Pic
ture
48
Pic
ture
49
A
B
BA
A
A
A
A
A
30
Pic
ture
50
Pic
ture
51
Pic
ture
52
Pic
ture
53
Pic
ture
54
U) Recommended lubricants
ELF
Epexa
GirelfSAE 90
Olna DS 68
SHELL
Retimax A
TransmissionSAE 90
Tellus 68
ESSO
Multi-purpose H
SprocketsST SAE 90
Nuto 68
YPF
61 – 62 EP
TransmissionSAE 90
Hydraulic oil68
BRAND
LUBRICANTGREASE
LUBRICANTOIL
OIL FOR HYDRAULICSYSTEM
A
A
A
A
A
B
31
V) End-of-season maintenance jobsOnce the seeding season is over and you prepare the machine for storage, be sure to follow safe.Maintenance procedures:
• Thoroughly remove seeds and fertilizer remains from boxes, meters and seed tubes, especially when seeds have been inoculated.
• Remove any fertilizer remains from boxes and meters.
• Proceed to blow out boxes, meters and seed tubes with compressed air.
• Low pressure-wash machine thoroughly, especially row units and any parts where dust or residue may deposit.
• Compressed air drying is recommended to prevent water deposits forming on components.
• Opener disks, blades, gauge wheels or any part which has been in contact with the ground must be coated with oil or grease to avoid rust.
• Lubricate entire machine in all grease fittings.
• Proceed to oil all chains and sprockets.
• Fully service machine: replace any missing or damaged parts.
• Repaint parts that have lost the original paint coat.
• Store machine on a hard flat surface, if possible sheltered.
• Set a wooden board under the opener disks and lower the machine to avoid digging them into the ground. This is to prevent all the weight of the machine to rest onto the wheels, causing their deformation.
• Relieve pressure from hydraulic hoses.
Check oil level in all gearboxes every 200 operation hoursor whenever there is any leak.
After the first 200 operation hours, it is recommended to emptyand wash gearboxes and refill them with new oil.
In dusty, sandy or dry soils lubrication periods should be shortenedto half the specified time.
WARNING
WARNING
WARNING
WHEN CLEANINGBOXES
Do not use water.Clean them with a brush
or compressed air.
32
PROBLEM CAUSE SOLUTION
CHAPTER VTroubleshooting
High residue in seeds Use clean seeds
Check and clean meters
Check surface to be fertilized
Check surface to be fertilized
Use dry fertilizer
Furrow not closing Reposition closing wheels
Operate slower
Field is wet
Seed tubesplug
Machine pulled bacwards withopeners in contact with the ground
Do not pull machine backwards withopeners touching the ground
Lower openers while machineis moving forward
Uneven seedmetering
Holes are formed due to dirtyor too small seeds
Use clean seeds andseeds ejector
Meters plugged by foreignsubstance
Fertilizertubes plug
Wet, lumpy fertilizer Use dry, free-flowing fertilizer
Machine pulled bacwards withopeners in contact with the ground
Do not pull machine backwards withopeners touching the groundLower openers while machine
is moving forward
Actual fertilizingrate different
than theestimated one
Incorrect choice of gear speedCheck gearbox speed
Fertilizer has absorbed humidity
Closing wheels not adjusted properly
Furrow coveredtoo deep with
loose soilOpeners throwing loose soil behind
Decrease opener down pressure
Furrow covered withsolid ribbon of soiltoo much compact
Allow field to dry
Hitch can´t belinked to the tractor
drawbarTractor drawbar is too low Adjust tractor drawbar at 50 cm
from the ground
Openers are lowered when machineis not moving forward
Openers are lowered when machineis not moving forward
33
Sharpen or replace openers.
Residue laying in bunches.
Inadequate down pressure.
Reduce speed when moving forward.
Tyres not properly inflated. Inflate tyres 20 pounds / inches 2.
Clean or replace valve.
Not enough hydraulic flow.
Poor openerspenetration
Hard ground conditions.Post-crop residue.
Too much or unevenlyspread residue.
Adjust gauge wheel fordeeper operation.
Increase down pressure.
Carry out harvest in goodsoil conditions.
Spread residue evenly across field.
Springs and / or openersnot adjusted properly.
Not the proper ones for that soil.
Adjust spring and openers depth.
Choose the proper opener disksfor that soil.
Unevenplanting depth
Spread residue evenly across field.
Increase down pressureto keep gauge wheel
in contact with the ground
Excessive speed on uneven ground.
Drive wheel doesnot turn freely
or turns unevenly
Hydraulic cylinders lowering cycleis not completed and the wheelis not in contact with ground.
Lower machine till cylinderscycle is completed.
Incorrect wheel height adjustment. Lower 1 or 2 grading adjustments
Loosen locked componentsand lubricate properly
Machine is not lowered completely.
Cinematic toolbar components arelocked or hardened by dirt or rust.
Lower machine till cylindersstop-ends.
Machine tendsto move to one side
A locked or misaligned wheel. Align wheel position by usingthe lock.
Disk marker excessively crossed. Reduce the disk marker crossing.
Only one markerdescends
Hydraulic cylinders cycle wasnot completed.
Perform the complete cylinders cycle
when machine is raised.
Dirty or damaged sequence valve.
Machine lowersunevenly
Cylinders opening cycle isnot completed.
Perform the complete cylinderopening and closing cycle.
The proportional flow divider valveis dirty or damaged. Clean, repair or replace valve.
Verify tractor hydraulic system.
PROBLEM CAUSE SOLUTION
34
CHAPTER V
PLANTER WORKING CAPACITY
FORMULA TO CALCULATE WORKING CAPACITY
Qty (hect./h) = Ww(m) x Sp(km/h) x Cx0,1
References:Qty: It’s the planted surface calculated in hectares per hour.Ww: Effective working width of machine calculated in meters (number of rows x row spacing in meters).Sp: It’s the effective working speed calculated in kilometers / hour.C: It’s the coefficient of time loss per turnings in corners and seed and /or fertilizer loads.0,1: Constant numerical value equal to the result in hectares per hour (hect./h), when the effective working width units (Ww) are expressed in meters (m) and the speed in kilometers/hour (Km/h).
If effective speed (Sp) is not indicated on tractor, it can be obtained by considering the time the machine takes in runninga certain distance.
Example:
Running distance: 100 metersTime invested in running that distance: 50 seconds
The coefficient (C) of time loss depends on the workingsystem.
If 15% time loss is assumed, the coefficient (C) results in a numerical value of 0,85.
Sp = 100 x 3,6 = 7,2 km/h 50
Example of working capacity calculation:
For a TD 21 module (24 rows at 21 cm spacing)Ww: 5,04 metersSp: 7,2 Km/hC. 0,85
This means that you will be able to seed 3,08 hectares in an hour at that speed (7,2km/h) considering that time loss (15%).
If speed or delays in turnings and seed/fertilizer loads vary, effective working capacity will vary, too.
Qty= 5,04m x 7,2Km/h x 0,85 x 0,1Qty = 3,08 hect./h
35
CHAPTER V1- Identification plate
2- Safety decalsIn case any of the decals is damaged, it can be replaced by ordering it under its spare part number.
SEMBRADORA PARA GRANOS FINOS
Place locks in theseeder lifting cylindersbefore transporting,servicingor adjustingmachine parts.
DANGERTO AVOID INJURY OR DEATH
Spare partnumber.
CAUTIONDRIVE WHEEL TIRE INFLATION PRESSURE
Minimum: 48 lbs/ inches2
Maximum: 58 bs/ inches2
CAUTIONInflation pressure for
11L15 / 400-60 x 15.5 tiresMinimum: 45 lbs/ inches2
Maximum: 52 lbs/inches2
I-4919
Don't stay within the coveragearea of the markersDANGER
WARNING
1- Ensure machine boxes are empty before transport.
2- Fill boxes only at work field.
3- Lift opener disks before transport. 4- Always lock up lifting cylinders before transport by placing locks.
5- Hydraulic failure can allow the machine to fall rapidly, causing injury or death.
TRANSPORT MACHINERY SAFELY
WARNING
Tractor should be in
oblique angle to
seeder to favor unlocked
wheels alignment.
WHEN ATTACHING SEEDER TO TRACTOR
WARNING
AVOID MACHINEEXTRA HEAVY WORK
Empty the machinebefore transport.
36
CAUTION
Transportposition.
WARNING
DO NOT- Stand or climb
on machinewhen operating.- Allow riders on implement.
Tighten bolts afterthe first eight hours’ work.
Check periodically.
CAUTION
CAUTIONHYDRAULIC CIRCUIT
MAXIMUN ALLOWED PRESSURE
150 – 170 bar.(2175 -2465 psi.)
I-8589
CAUTIONHYDRAULIC OIL
UTTO Requirements(universal tractors transmission oils)
SAE: 10 W-30or SAE: 15W-30
I-7931
WARNING
WHEN CLEANING BOXESDo not use water.
Clean them with a brushor compressed air.
HYDRAULIC CIRCUITTo ensure correct operation and
durability of hydraulic valvesand cylinders, filter and clean
hydraulic fluids carefully.Clean quick-attach couplingsbefore connecting to tractor.
WARNING
DO NOT TURN WHILE OPENER
DISKS ARE IN FULL CONTACT
WITH THE GROUND
during seeding operation.
WARNING
Transport maximumspeed.
37
I-8212
WARNING
38
TABLE OF CONTENTS
Chassis 39Chassis for Model TD21, 30 rows 40Rear hydraulic suspension – Model TD21, 30 rows 41Transport hitch 42Work hitch 43Work hitch w/hydraulic lifting – Model TD21, 30rows 44Work hitch w/hydraulic lifting – Model TD21 x 36 and48 rows 45Spring: square shaft rocking – hitch lifting for 2-modulemachine 47Drive Wheel 48Working / Transport Wheel - 13”x 15.5” 50Wheel hub 51Vertical lock in wheel fork 52Working / Transport Wheel 10.5 x 17.5 TD21- 30 rows 53Working/Transport Wheel hub - 10.1/2" x 17.1/2" - TD 21, 30 rows 54Row marker 55Foldable row marker extension attachment w/o lateralthreaded rod 56Foldable row marker extension attachment w/ lateralthreaded rod 57Modules side linkage – TD 21 – 36 and 48 rows 58Rear catwalk 59Fertilizer box and seeds single box 60Fertilizer meter and outlet tube 61Seeds meter and outlet tube 62Countershaft for Chevron wheel-type meter TD 63Transmission: fertilizer box end drive 64Transmission: general sowing drive with gearbox 65Transmission: general fertilizing drive with gearbox 66Row unit anchor 67Opener disk 68Conical stamped, 15.5”coulter blade w/hub 69Assembled gauge Wheel – 2.3/4” x 15” 70Closing disk set rim – 14” 71Seed firming skid 72Press wheel - 1”x8” (Optional item) 73Front 16” coulter blade unit w/ anchoring set 74Hydraulically operated drying fan (Optional item) 75Hydraulic jack 76Front catwalk for lucerne box (Optional item) 77Lucerne box assembly (Optional item) 78Transmission: fertilizer gearbox (Optional item) 79Lucerne meter (optional item) 80
Page
SPARE PARTS
To order spare parts the following must be considered:Look up the part in this manual by observing the pictures and reading the corresponding parts lists.
Place your order clearly and be sure to include:a) Part code.b) Part name.c) Quantity. d) Model, series and machine number.
If there is no dealer available in your area, leave addressee´s full name and address where the part has to be delivered.(Indicate shipping company and conditions)
PIEROBON S.A. reserves the right to modify the products introduced in this manual due to technichal or commercial reasons, thus not implying any kind of obligation on its part.
How to order spare parts
WARNING: to identify the right or leftside of a spare part, look at the seederin working position from its rear part.
39
CHASSIS
A5141-A-06/2010
GI-GRAMPA 5/8"A=178-LP=152TUERCA*UNC-5/8"AUTOFRENA-ZSUJETADOR LAT. DESPLAZADO MANGU.CHASIS DE SEMBRAD.TD21x24 LINEASCHASIS DE SEMBRAD.TD21x18 LINEASRES*CLAV.Nº41-4½mm COMUN-ZPASADOR C/MANGO De= 3/4" L=130TOPE GOMA AMOR.LANZA TRASLADOBASE SOSTEN GATO C/GRAMPA TD24/30PASADOR De=3/8"L=145 DE SOP.GATO RES*CLAV.Nº41-4½mm COMUN-ZLLAVE P/AJUSTE TORNILLOS DE RUEDA
17603717405650135041440314137835505841334403397 R
123456789
101112
IIPPPIPIPPIP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
65
7
6
57
3
3
4
3
2
1
229
8
1
10
11
40
CHASSIS FOR MODEL TD21, 30 ROWS
A9149-A-07/2010
PRISIONERO 3/8"x5/8" RWPASADOR PARRILLA D=25,4 L=141 CHASIS DE SEMBRAD.TD21x30 LINEASCRUCERO TRANSV.P/RUEDA C/SUSPEN.TUERCA RW 1/2" EXAG=19-ZTORNI AC G5-5/8"x2" UNCAMORTIGUAD.A GAS Cod.23040TUERCA*UNC-5/8"AUTOFRENA-ZRES*CLAV.Nº38-3½ mm.L=92-ZCHAVETA PARTIDA 2½x 20 -ZARANDELA PLANA 5/16"BISE-ZBUJE De=21 Di=14 L=22PASADOR C/MANGO De= 5/8"L=55BUJE TRATADO C/TOPE P/BRAZOS ESCALERA ANCHA DE ASCENSO LATE.TORNILLO CONEXION AMORTI.ESCALERABARRA CUADR.DEL.IZQ.P/CUERPOS BARRA CUADR.DEL.DER.P/CUERPOS TUERCA*UNC-5/8"AUTOFRENA-Z
12836102742374262214232035753717440445337175326 H3019320970337129724572443717
123456789
10111213141516171819
IPPPIIIIIIIPPPPPPPI
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
ADETALLE: A
9
13
17
4
?
4
3
18
21
2
86
11
15
14
6 16
7
12
5
11
8
10
41
REAR HYDRAULIC SUSPENSION – MODEL TD21, 30 ROWS
A9226-A-07/2010
PRISIONERO 3/8"x5/8" RWNIPLE ENGRASE 1/4"SAE-67°TORNI ACE.G5-1/2"x3.1/4"RWTUERCA*RW-1/2"AUTOFRENAN-ZARO SEEGER 38 x 1,7 P/EJEBUJE TRATADO De=48 Di=38 L=45 PASADOR PARRILLA D=25,4 L=141 SOPORTE INTERMEDIO TRASERO DE SUSP.PERNO PARALELOGRAMO P/SEEGERPARRILLA SUP.PLEG.SUSPENSION RUEDA PARRILLA INF.PLEG.SUSPENSION RUEDA
12832184493256115954601161027008723374337434
123456789
1011
PPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
9
9
5
5
6
6
6
6
6
11
9
9
5
5
4
3
5
5
7
66
5
57
6
11
10
8
11
2
2
2
42
TRANSPORT HITCH
A5246-A-06/2010
TORNI 1/2"x1.3/4"EXAG.RW-ZNIPLE ENGRASE 1/4"SAE-RECTTUERCA UNC 1" EXAG=35-ZARANDELA GROWER 1"RES*CLAV.Nº41-4½mm COMUN-ZRES*CLAV.Nº38-3½ mm.L=92-ZTUERCA*RW-1/2"AUTOFRENAN-ZTORNI AC G5-1"x 5.1/2" UNCPIE SOPORTE DE LANZA TRABAJOPASADOR C/MANGO De= 3/4" L=105BUJE INTERIOR DE MUÑECA(26)LANZA LANZA DE TRASLADO(26)LONGITUDINALLANZA DE TRASLADO(26)TD 21 X 30MUÑECA P/BUJES(26) LANZA TRABAJOBARRA GUIA(26)TIRO LANZA TRASLA.
206421812302236244034404561176771507220227845097737173417372
123456789
101112
1314
IIIIIIIIPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
9
1
67
1210
5
14
3
8
11
8
11
1322
43
4
8
11
34
8
34
11
132
2
43
WORK HITCH
A5185-A-06/2010
TORNI 1/2"x1.3/4"EXAG.RW-ZTORNI 1/2"x4" EXAG.RW-ZTORNI 5/8"x3" EXA.UNC-ZTORNI 5/8"x3.1/2"EXA.UNC-ZTORNI 5/8"x4.1/2"EXA.UNC-ZNIPLE ENGRASE 1/4"SAE-RECTOCONTRATU.5/8"UNC E24-A=7-ZTORNI AC G5-3/4"x8" UNCTUERCA UNC 1" EXAG=35-ZTORNI AC G5-3/8"x1" UNCTORNI AC G5-5/8"x2" UNCTUERCA UNC 3/4" EXAG=27-ZARANDELA GROWER 3/8"ARANDELA GROWER 3/4"ARANDELA GROWER 1"ARANDELA PLANA 5/8" -ZGI-GRAMPA 3/4"A=141-LP=205TUERCA*UNC-5/8"AUTOFRENA-ZTUERCA*UNC-3/4"AUTOFRENA-ZRES*CLAV.Nº38-3½ mm.L=92-ZTORNI AC G5-3/4"x4.1/2"UNCTUERCA*RW-1/2"AUTOFRENAN-ZTORNI AC G5-3/4"x9" UNCRESOR A12,7-De=61 L=465 EXTORNI AC G5-1"x 5.1/2" UNCARANDELA De=41 Di=11 E=8OJO CONEXION SOPORTE MANGUERAGUIA PARA MANGUERASPIE SOPORTE DE LANZA TRABAJORIENDA DE SOSTEN LANZA TRABAJO
2064207220972099210121812248228423022309232023442355236023622374344537174112440444655611587272327677343 S372 L1499 A15072519
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIIIIPPPPP
BUJE INTERIOR DE MUÑECA(26) LANZAPASADOR C/MANGO De= 5/8"L=55PLACA CENTRAL UNION LANZAARANDELA De=36 Di=20 E=6PLACA DERECHA FIJACION CRUCEROCRUCERO UNION BRAZOS LANZAPLACA IZQUIERDA FIJACION CRUCEROGUSANO C/TUERC.RESOR.ALAMBREBUJE CONICO ASIENTO DE TORMILLOTAPA "U" C/GRAMPA DE PLEGADOTUBO C/VASTAGO ROSCADO TIRA RES.PLEGADO LANZA TRAB(26) DERECHAPLEGADO LANZA TRAB(26) IZQQUIERDATAPA "U" DE PLEGADO CONEXIÓNMUÑECA P/BUJES(26)DE LANZABAJADA TIRO(D)LANZA(26)UNIVERSALBAJADA TIRO LANZA(26)UNIVERSAL
27843019394039463947395139574158419744254426446144627138734173817382
3132333435363738394041424344454647
PPPPPPPPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
28
5
2722
21
33
18
20
29
122
4
42
43
35 2
22
3637
18
32
20
30
111616
18
25
31 6
4531
25
915
47
17
40
915
1412
19
339
738
24
38159 7
46101326
41
915
25
31
3145
251914
44
23
834
34
44
WORK HITCH W/HYDRAULIC LIFTING – MODEL TD21, 30ROWS
A9220-A-07/2010
TORNI 1/2"x1.3/4"EXAG.RW-ZTUERCA CASTILLO 1.1/4" UNFTORNI AC G5-3/4"x8" UNCTORNI AC G5-5/8"x5" UNCTUERCA UNC 3/4" EXAG=27-ZARANDELA GROWER 3/4"CHAVETA PARTIDA 5 x 40 -ZGI-GRAMPA 3/4"A=141-LP=205TUERCA*UNC-5/8"AUTOFRENA-ZRES*CLAV.Nº41-4½mm COMUN-ZTUERCA*RW-1/2"AUTOFRENAN-ZTORNI AC G5-3/4"x9" UNCPERNO PASADOR C/CAB.De=15,87 L=42ARANDELA De=52 Di=32 E=1PIE SOPORTE DE LANZA TRABAJOPASADOR C/MANGO De=1" L=155TORNILLO 1.1/4" UNF L=155 DE LANZABUJE INTERIOR LARGO(19,5)PROLON.CIL.PASADOR C/MANGO De= 5/8"L=55ANILLO C/OJO GUIA MANGUERAS HIDRA.ARANDELA De=36 Di=20 E=6CUERPO MAYOR LANZA TRABAJO RIENDA SOSTEN LANZA DE TRABAJO PERNO PASADOR DE BISAGRA LANZA EMBOLO DEL CILINDRO LEVANTE LANZA TAPA U DE PLEGADO CONEXION RIENDALANZA ENGANCHE AL TRACTOR BAJADA TIRO LANZA C/CONEX.CILINDROBAJADA TIRO LANZA TUBO SEPARADOR TRANS. LANZA L=100
20642158228423262344236025253445371744035611587221811465 R1507220325582790301931353946702970347036704771387200720472057352
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIPPPPPPPPPPPPPPPPP
RES*CLAV.Nº38-3½ mm.L=92-ZTORNI AC G5-5/8"x2" UNCARANDELA PLANA 5/8"E=3,2-ZCHAVETA PARTIDA 5 x 40 -Z I-3268 MANGU.HID.312-4-4xR1-1/4"x5650x35HID.ADAPT.748- 4- 4HID.TAPON PVC P/PNH MACH.½HID. VALV.RED.611-4i(D=1)8CILINDRO HID. 2.1/2" X 304 LEVANTE LANZAHID.ACOPL.RAP.MACHO PNH ½"
440423202374252550732333245444459244729
31323334353637383940
IIIIAIIIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
27
11
15
1
1017
4
16
2
9
22
8
12
3
2126
2413
29
5
6
14 28
18
14
2524
32 33
20
9
12
3
21
26
5 6
7
1019
31
23
13
34
30
37
40
38
35
39 36
45
WORK HITCH W/HYDRAULIC LIFTING – MODEL TD21 X 36 AND 48 ROWS
A7024-A-09/2010
TORNI 5/16"x3/4" EXA.UNC-ZTORNI 1/2"x1.3/4"EXAG.RW-ZTUERCA~CASTILLO 1.1/4" UNFTUERCA UNC 3/8" EXAG=16-ZNIPLE ENGRASE 1/4"SAE-RECTCONTRATU.7/8"UNC EXAG=32-ZTUERCA UNC 1" EXAG=35-ZTORNI AC G5-5/8"x2" UNCTORNI AC G5-5/8"x2.1/2"UNCTORNI AC G5-3/4"x4" UNCTORNI AC G5-3/8"x3.1/2"UNCTUERCA UNC 3/4" EXAG=27-ZARANDELA GROWER M- 8ARANDELA GROWER 3/8"ARANDELA GROWER 3/4"ARANDELA GROWER 1"CHAVETA PARTIDA 5 x 40 -ZGI-GRAMPA 3/4"A=141-LP=205TORNI AC G5-5/8"x4" UNCTUERCA*UNC-5/8"AUTOFRENANTERESOR A3½-De=28 L=66 COM-ZRES*CLAV.Nº41-4½mm COMUN-ZRES*CLAV.Nº38-3½ mm.L=92-ZTORNI AC G5-3/4"x4.1/2"UNCTORNI AC G5-3/4"x5" UNCTUERCA*RW-1/2"AUTOFRENANTETACO GOMA AMORTIG.71244563TUERCA UNC 5/16" EXAG=12-ZTORNI CLAS*10.9-3/4x5.½UNFTORNI AC G5-1"x 5.1/2" UNC
201720642158216721812250230223202322232323252344235423552360236225263445363737174195440344044465446656116630670876377677
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIIIIIIIII
ROSCA 7/8" C/GRAMPA REGISTRO RIENDAROTULA Di=3/4" C/ROSCA 1.1/8" L=170 REGICONTRATUERCA 1.1/8"UNC CON MANGOBUJE LARGO(20)INTERIOR DE MUÑECA LANZAPIE SOPORTE DE LANZA TRABAJOPASADOR DE TRABA LANZA TUBULAR PASADOR C/MANGO De= 3/4" L=105PASADOR C/MANGO De=1" L=155RIENDA 60x40 L= 920 TIRO INT.LATERAL LAN.RODILLO SEPARADOR DE BAJADA TIRO LAN.MEDIA CAÑA TRABA CILINDRO LANZA ARANDELA De=54 C/AG.ROSCADO 1/2" REG.TUBO SEPARADOR TRANSVERSAL L=60TUBO C/CORREDERA CONEXION CILINDRO TORNILLO 1.1/2" UNF L=155 DE LANZA BUJE DE PUNTA EJE CUADRADO LEVANTE HID.BUJE INTERIOR DE MUÑECA(26)LANZA C/LEV.BUJE INTERIOR(Di=19«)EJE CUADR.LEV.HIDR.ARANDELA De=47 Di=26 E=5TRANSV.CONEX.LANZA ENG.TRACTOR LANZA ENGANCHE AL TRACTOR S/RIENDA RIENDA 60x40 L= 820 CONEXION LANZA ARANDELA De=44 Di=20 E=8BAJADA INTERM.C/MUESCA TIRO LANZA EJE CUADRADO LEV.(26)HIDRAULICO LANZA BAJADA INTERMEDIA(26)TIRO LANZA C/HIDR.BAJADA LATERAL(26)DE TIRO LANZA C/HIDR.MUñECA P/BUJES(26)DE LANZA TRABAJO RIENDA 72x52x1360(26)EXT.LAT.LANZA RIENDA 72x52x1335(26)INTER(DER)C/CONEX.
302 L 320 S 321 S1413 A15072190220222032497250325062507251425182558266227842789322341424143414641964385445944674468734173767377
313233343536373839404142434445464748495051525354555657585960
PPPPPPPPPPPPPPPPPPPPPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
51262
35 23 45 3822
11 43
24
25
173
50
53
32
33 39
53
3233
5220
52
631
31639
61
60
36
21
37
22
2136
37
22
59
5930
30
1857
1215
7
7
16
58
46
47 4716
17121514
4
830 ?
41209
49 44
208
4040
2954
1215
414
11 55
56
57
4758 47
47
58
271328
14747
58
5
42
19
4827
4747
5816
720 5
30
47
716
64
6665
62
68 6763
46
WORK HITCH W/HYDRAULIC LIFTING – MODEL TD21 X 36 AND 48 ROWS
A7024-A-09/2010
RIENDA 72x52x1335(26)INTER(IZQ)LANZAI-3268 MANGU.HIDR.312-4-4xR1-1/4"x5650HID. ADAPT.748-4-4HID.TAPON PVC P/PNH MACH.½HID. VALV.RED.611-4i(D=1)8HID.ACOPL.RAP.MACHO PNH ½"HID.TAPON 78-4 CIL.HIDR.2½"x254 PROLONGAD.
7378507323332454444472981752467
6162636465666768
PAIIIIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
51262
35 23 45 3822
11 43
24
25
173
50
53
32
33 39
53
3233
5220
52
631
31639
61
60
36
21
37
22
2136
37
22
59
5930
30
1857
1215
7
7
16
58
46
47 4716
17121514
4
830 ?
41209
49 44
208
4040
2954
1215
414
11 55
56
57
4758 47
47
58
271328
14747
58
5
42
19
4827
4747
5816
720 5
30
47
716
64
6665
62
68 6763
SPRING: SQUARE SHAFT ROCKING – HITCH LIFTING FOR 2-MODULE MACHINE
47A7042-A-09/2010
TORNI 1/2"x1.1/2"EXAG.RW-ZTORNI 5/8"x3.1/2"EXA.UNC-ZCONTRATU.5/8"UNC E24-A=7-ZTORNI AC G5-5/8"x2.1/2"UNCTUERCA UNC 5/8" EXAG=24-ZARANDELA GROWER 1/2"ARANDELA GROWER M-16RESOR A8-De=51 L=220 EXPANARANDELA De=38 Di=17 E=6 (ZINCADA)GUSANO C/TUERCA 5/8"UNC P/ALAMBRE 8 mmGUSANO C/RIENDA LARGA TIRA RESORTE BUJE CONICO ASIENTO DE TORNILLO RESORTEBUJE TOPE PARAL.SUPERIOR CONEX.RESORTEBRAZO TIRA RESORTE BALANCEO EJE CUAD.
20632099224823222343235723594238331 S26492650419750105057
123456789
1011121314
IIIIIIIIPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
2
13
14
61
310
8
11
7
13
9
4
5
48
DRIVE WHEEL
A5148-A-07/2010
CADENA DE RODILLOS ASA 50UNION P/CADENA ASA 50TORNI 1/2"x1.1/2"EXAG.RW-ZTUERCA RW 7/16" EXAG=19-ZTUERCA UNC 3/4" EXAG=32-ZNIPLE ENGRASE 1/4"SAE-RECTNIPLE ENGRASE 1/4"SAE-67°CONTRATU.3/4"NC E=27 A10-ZTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 7/16"ARANDELA GROWER 1/2"ARANDELA GROWER 3/4"ARANDELA PLANA 1/2" -ZCHAVETA PARTIDA 5 x 30 -ZCHAVETA PARTIDA 6 x 35 -ZRESORT Nº55-De=51x304 CO-PRES*CLAV.Nº38-3½ mm.L=92-ZTORNI AC G5-3/4"x9" UNCRODAMIENTO 6201 RS2PERNO PASADOR C/CAB.De=23ARANDELA Di=20 TOPE Y GUIABRAZO CONEXION CORTO DADOENGR. Z 14 x 5/8" TENSOR CADENARODAMIENTO 6206 RS2EJE TRANS. LARGO P/RUEDA MOTRIZ GUARDA CADENA RUEDA MOTRIZARANDELA GROWER 3/4"GUSANO ALLEN 1/2"RWx3/4"-ZCAJA RODAM.PUNTA DE EJE Y HORQUILLACHAVETA PLANA 5/16" L= 60
11311151206321682172218121842249234123562357236023722525252943134404587266061442163520052095542272030882360362321562229
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIPPPPIPPIIPP
BUJE PORTA RODAMIENTO HORQUILLAVASTAGO ROSCADO FIJACION HORQUILLAANILLO SEPAR.41x30x10 HORQUILLAENGR.Z16x5/8" TRIPLE P/EJE RUEDA MOTRIZRODAMIENTO 6206 RS2TORNI 5/16"x1" EXA.UNC-ZTORNI 1/2"x1.1/4"EXAG.RW-ZARANDELA GROWER M-16TORNI 1/2"x4.1/2"EXAG.RW-ZTORNI 5/8"x1.1/2"EXA.UNC-ZTUERCA UNC 5/8" EXAG=27-ZTORNI AC G5-3/8"x1" UNCTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 3/8"ARANDELA GROWER 1/2"EJE SOPORTE APRETADOR CADENADADO GUIA EMBOLO PRESION RUEDAESPARRAGO FIJADOR BUJE C/TEMBOLO REGISTRO PRESION RUEDAPASADOR C/MANGO De= 5/8"LPLACA REGISTRO ALTURA RUEDAPLACA SOPORTE BUJE C/RODAMIENTOARANDELA De=47 Di=10 E=3PUNTA DE EJE P/RUEDA MOTRIZENGR. Z 30 x 5/8" PUNTA DE EJEARANDELA De=32 Di=10 E=5 ZINCADA BUJE C/TUERCA DE EMBOLO PRNEUM.6.00x16"6/8 T-MILITARCAMARA P/NEUMATICO 600x16"TUERCA UNC 5/16" EXAG=12-Z
27172718390150225422019206223592073209121712309234123552357212521132140214722013059306021142136309922382139294466356708
313233343536373839404142434445464748495051525354555657585960
PPPPIIIIIIIIIIIPPPPPPPPPPPPIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
64
64
21
22
2247
49
6
14
17
1650 29
24
28 34
33
3518
39
3335
31
52
4543
3257
25
30
2924
20
15
26
3636
60
60
42
4453
62
55
51
125
7
485
527
27
21
8 8
119
2924
2924
54
63
61
3841
59
58
125
1923
8
46
1013
10
4
13 3
4537
5644
42
40
49
DRIVE WHEEL
A5148-A-07/2010
LLANTA 4.1/2"x16" 4 AGUJ.P/NECHAVETA PLANA 5/16" L= 30TUBO SEPARADOR PUNTA DE EJEBRAZO SOP.GRAL RUEDA MOTRIZ
206 B345 J23462713
61626364
PPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
64
64
21
22
2247
49
6
14
17
1650 29
24
28 34
33
3518
39
3335
31
52
4543
3257
25
30
2924
20
15
26
3636
60
60
42
4453
62
55
51
125
7
485
527
27
21
8 8
119
2924
2924
54
63
61
3841
59
58
125
1923
8
46
1013
10
4
13 3
4537
5644
42
40
50
WORKING / TRANSPORT WHEEL - 13”X 15.5”
A7069-A-07/2010
PRISIONERO 3/8"x5/8" RWNIPLE ENG.1/8"GAS-E=9½-RECNIPLE ENGRASE 1/4"SAE-RECTNIPLE ENGRASE 1/4"SAE-67°TORNI AC G5-3/8"x1.1/4"UNCTORNI AC G5-5/8"x2" UNCTUERCA UNC 3/8" EXAG=14-ZARANDELA GROWER 3/8"ARANDELA GROWER 5/8"ARANDELA PLANA 3/8" -ZCHAVETA PARTIDA 5 x 50 -ZNEUMATICO 400/60-15,5"-14PTUERCA*UNC-5/8"AUTOFRENA-ZRES*CLAV.Nº38-3½ mm.L=92-ZRODAMIENTO 32016 XTORNI ACE.G5-1/2"x3.1/4"RWTUERCA*RW-1/2"AUTOFRENAN-ZARO SEEGER 38 x 1,7 P/EJEPASADOR De= 3/8"L=120 P/MED. TRABA SEGURIDAD P/EJE DE RPROLONG.SOPORTE CONEXION CILINDRO BUJE DE SOPORTE HORQ.DELANTEROBUJE TRATADO De=48 Di=38 L=45DISCO DE SEGURIDAD EJE VERARANDELA CIERRE INF.ROD.HOPASADOR PARRILLA D=25,4 L=45HORQUILLA DE RUEDA DESPLAZ.BUJE SOPORTE HORQUILLA RUEDAPARRILLA SUPERIOR DE RUEDAPARRILLA INF/SUP.DE RUEDA
128321802181218423132320234023552359237025262745371744044850493256115954316 L34125096600160116028605961027002700570067007
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIPPPPPPPPPPPP
MEDIA CAÑA TRABA LARGA CILINDROTORNILLO 5/8"x 1.1/2" SUJECCIONPASADOR C/CABEZA DE BRAZOPERNO PARALELOGRAMO LLANTA 13x15,5"MULT.C=150CONTRATUERCA 1/2" W-12H EX=19-ZTORNILLO 1/2"X1" C/TUBO SUJ.BUJE ASIENTO DE BOLA TRABA RUEDA
70407079720372337286703327883848
3132333435363738
PPPPPIPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
21
26
34
23
18
23
18
434 18
29
23
2318
613
19
1431
423 18
23
34
18
30
1
11
33
18
34 23
23
1836
37
3329
24
22
28
217
16
15
25
27
7
8
20
105
2035
12
38
51
WHEEL HUB
A9721-A-06/2010
RODAMIENTO 6207RETEN SAV/DBH 5141TUERCA UNC 1" EXAG=35-ZRODAMIENTO 6207 RS1PIII_TORNI.FORJ.5/8" LT=57TUER-CONI.90ºNF-5/8"E=27-ZSEPARADOR DE EJE RUEDA P/HORQUI.PUNTA DE EJE RUEDA DESPLAZMAZA RUEDA DESPL.P/LLANTA 13x15½"
5449532302274433406709341334147289
123456789
IIIIIIPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
3
7
2
4
1
8
5
9
14
7
3
2
6
52
VERTICAL LOCK IN WHEEL FORK
A5253-A-06/2009
RESORT Nº50-De=28x87 COMPNIPLE ENGRASE 1/4"SAE-RECTOTORNI ACE.G5-1/2"x1.3/4"RWTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 1/2"TUERCA*UNC-5/16"AUTOFREN-ZRES*CLAV.Nº41-4½mm COMUN-ZTORNI ACE.G5-1/2"x2.1/4"RWARANDELA PLANA 5/16"BISE-ZTORNI AC G5-5/16x1.3/4"UNCARANDELA De=35 Di=13,5 E=5BUJE GUIA PERNO TRABA VERTICALPALANCA PLASTIFICADA DE TRABASUPLEMENTO INFERIOR REFUERZOPERNO INTER.P/LEVA VERTICAL C/BOLAPERNO INTER.P/LEVA VERTICAL S/BOLA
1039218123162341235741514403674671757225381 G50835084728750805079
123456789
10111213141516
IIIIIIIIIIPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
8
118
1112
23
1114
11
5
4
10
9
13
5
11
4
7
6
4
115
15
1
53
WORKING / TRANSPORT WHEEL 10.5 X 17.5 TD21- 30 ROWS
A9225-A-08/2010
PRISIONERO 3/8"x5/8" RWNIPLE ENG.1/8"GAS-E=9½-RECNIPLE ENGRASE 1/4"SAE-RECTNIPLE ENGRASE 1/4"SAE-67°TORNI AC G5-3/8"x1.1/4"UNCTUERCA UNC 3/8" EXAG=14-ZARANDELA GROWER 3/8"ARANDELA GROWER M-16ARANDELA PLANA 3/8" -ZCHAVETA PARTIDA 5 x 40 -ZRES*CLAV.Nº38-3½ mm.L=92-ZRODAMIENTO 32016 XTORNI ACE.G5-1/2"x3.1/4"RWNEUM.MITAS-TR10*14-17½TRACTUERCA*RW-1/2"AUTOFRENAN-ZARO SEEGER 38 x 1,7 P/EJEPASADOR De= 3/8"L=120 P/MEDIA CAÑABUJE DE SOPORTE HORQ.DELANTERA BUJE TRATADO De=48 Di=38 L=45 DISCO DE SEGURIDAD EJE VERTICAL ARANDELA CIERRE INF.ROD.HORQ.RUED.HORQUILLA DE RUEDA DESPLAZAMIEN.LLANTA 10,5x17,5" MULT.C=150 P/NEU.BUJE SOPORTE HORQUILLA RUEDA DES.PARRILLA SUPERIOR DE RUEDA DESPLA.PARRILLA INF/SUP.DE RUEDA DESPLA.MEDIA CAÑA TRABA LARGA CILINDRO TORNILLO 5/8"x 1.1/2" SUJECC.Y LUBRIC.TRABA SEGURIDAD P/EJE DE RUEDA PASADOR C/CABEZA DE BRAZO INFER.
1283218021812184231323402355235923702526440448504932532856115954316 L6001601160286059700270047005700670077040707970837203
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIPPPPPPPPPPPPPP
PERNO PARALELOGRAMO P/SEEGERCONTRATU.1/2"W-12H"EX=19-ZTORNILLO 1/2"x1"C/TUBO SUJECCION
723370332788
313233
PIP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
29
67
95
29
22
2314
2112
2
24
18
20
328
8
1727
11
1631
19
1631
19
19
161
26
3010
31
3116
16
19
19
1916 25
19
16
19163233
4
13
15
54
WORKING/TRANSPORT WHEEL HUB - 10.1/2" X 17.1/2" - TD 21, 30 ROWS
A9227-A-08/2010
RODAMIENTO 32208TAPON ACERO 1/4"SAE-28 H"PIII_TORNI.FORJ.5/8" LT=57RETEN SAV/DBH 8161ARANDELA AJUSTE 48x40x0,2TUER-CONI.90ºNF-5/8"E=27-ZTUERCA UNC 1"1/4"EXAG=44-ZMAZA RUEDA DESPL.P/LLANTAPUNTA DE EJE RUEDA DESPLAZAMIENTOSEPARADOR DE EJE RUEDA
576141833405759576067097542700370377038
123456789
10
IIIIIIIPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
7
104
1
9
5
8
6
7
10
4
1
5
3
2
55
ROW MARKER
A1006-B-11/2010
GI-GRAMPA 1/2"A=74-LP=70-ZTORNI 5/16"x3/4" EXA.UNC-ZNIPLE ENGRASE 1/4"SAE-RECTCONTRATU.3/4"NC E=27 A10-ZTORNI AC G5-5/8"x1.3/4"UNCTORNI AC G5-5/8"x2" UNCTORNI AC G5-5/8"x2.1/2"UNCTORNI AC G5-3/8"x3.1/2"UNCTUERCA UNC 3/8" EXAG=14-ZTUERCA RW 1/2" EXAG=22-ZTUERCA UNC 5/8" EXAG=24-ZARANDELA GROWER 5/16"ARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA GROWER 5/8"TORNI AC G5-5/8"x4" UNCTUERCA*UNC-5/8"AUTOFRENA-ZRES*CLAV.Nº41-4½mm COMUN-ZTORNI AC G5-5/16x1.1/2"UNCTACO GOMA AMORTIG.71244563RESOR A8-De=49 L=137 COM-PRESOR A10-De=51 L=147 CO-PTUERCA UNC 5/16" EXAG=12-ZRODAMIENTO 30203RODAMIENTO 30204RETEN SAV/DBH 5124TORNI 5/16"x1/2" EXA.UNC-ZTORNI AC G5-5/16x1.1/4"UNCTORNI 1/2"x1.1/2"EXAG.RW-ZTORNI 1/2"x3" EXAG.RW-Z
105420172181224923192320232223252340234123432354235523572359363737174403494866306660666167085605619522015670720632069
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIIIIIIIII
TUERCA-UNF 5/8" EXAG=24-ZTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 1/2"ARANDELA GROWER 5/8"ARANDELA PLANA 1/2" -ZARANDELA PLANA 5/8" -ZARANDELA_ABANICO EXT*A-8,4CHAVETA PARTIDA 3 x 30 -ZRESO.ANILLO SEGURI.52½x3-ZARANDELA Di=20 TOPE Y GUIABRAZO MARCADOR DISTANCIA BRAZO MARCADOR DIST.CORTOBASE SOPORTE GRAL MARCADOR DERECHOBASE SOPORTE GRAL MARCADOR IZQUIERDOPASADOR DE BRAZO MARCADORBUJE INTER.CORTO(Di=16,5) PR.EMBOLO DEL AMORTIGUADOR MARCADORMEDIA CAÑA TRABA CILINDROBUJE GUIA RESORTE MARCADORANGULO CORTO CONEXION DISCOGUARDAPOLVO DE MAZA DEL DISCOMAZA DE RODAMIENTOS P/DISCOEJE DE MAZA DISCO MARCADOR 388 C TUERCA CASTILLO 5/8"UNFDISCO CONCAVO DENTADO 14" C.PLANODISCO ESTAMP.LIMITADOR PROBARRA INTER.MARCADOR L=1200BARRA INTER.MARCADOR L=800ARANDELA_ABANICO EXT*A-8,4
2162234123572359237223742390252144051635200970882024202520302034208523753978308 J339 B380 A381 A388 C926 D2107234020872390
3132333435363738394041
424344454647484950515253545556
57
IIIIIIIIIPPPPPPPPPPPPPPPPPPPI
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
55
28
37
50
51
24
53
2712
54
2526
39
38
52
56
49
10
10 3134
35
33
29
30
37
11
46
22
40
40
21
4844 41
11432
4718
1645
17
4442
205723
2
65
11
11
19
1223
8
9
13
33
15
15
36 43
56
FOLDABLE ROW MARKER EXTENSION ATTACHMENT W/O LATERAL THREADED ROD
A4004-A-07/2010
TORNI 5/16"x1" EXA.UNC-ZTORNI 1/2"x1.3/4"EXAG.RW-ZTUERCA UNC 7/8" EXAG=32-ZNIPLE ENGRASE 1/4"SAE-RECTONIPLE ENGRASE 1/4"SAE-67°TORNI AC G5-5/8"x3.1/2"UNCTORNI AC G5-5/8"x2.1/2"UNCTORNI AC G5-3/8"x3" UNCTUERCA UNC 3/8" EXAG=14-ZTUERCA UNC 5/8" EXAG=24-ZARANDELA GROWER M- 8ARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA PLANA 1/2" -ZTUERCA*UNC-5/8"AUTOFRENA-ZRES*CLAV.Nº41-4½mm COMUN-ZTORNI AC G5-5/16x1.1/2"UNCTACO GOMA AMORTIG.71244563TUERCA UNC 5/16" EXAG=12-ZPASADOR DE BRAZO MARCADORBUJE INTER.CORTO(Di=16½)PROL.CIL.PROLONGACION DE MARC. TD21X30 Y 36 LIN.ROSCA 7/8" REGISTRO VASTAGOARANDELA ABANICO EXT*A-8,4
201920642173218121842295232223242340234323542355235723723717440349486630670820302034314838662390
123456789
101112131415161718192021222324
IIIIIIIIIIIIIIIIIIIPPPPI
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
2017
1119
5
22
10
723
3
3
4
213
14
213
14
1521
6
9
12
8
19
24 18
1
1
19 24
57
FOLDABLE ROW MARKER EXTENSION ATTACHMENT W/ LATERAL THREADED ROD
A5248-A-09/2010
TORNI 1/2"x1" EXAG.RW-ZTUERCA UNC 3/4" EXAG=32-ZTUERCA UNC 7/8" EXAG=32-ZNIPLE ENGRASE 1/4"SAE-RECTCONTRATU.3/4"NC E=27 A10-ZTORNI AC G5-5/8"x3.1/2"UNCTORNI AC G5-5/8"x2" UNCTORNI AC G5-5/8"x2.1/2"UNCTORNI AC G5-3/8"x3" UNCTUERCA UNC 3/8" EXAG=14-ZTUERCA UNC 5/8" EXAG=24-ZARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA_ABANICO EXT*A-8,4ARANDELA GROWER M-16 CHAVETA PARTIDA 5 x 30 -ZCHAVETA PARTIDA 6 x 40 -ZTUERCA*UNC-5/8"AUTOFRENA-ZTORNI AC G5-5/16x1.1/2"UNCTACO GOMA AMORTIG.71244563RESOR A10-De=51 L=147 CO-PTUERCA UNC 5/16" EXAG=12-ZARANDELA Di=20 TOPE Y GUIA EMBOLOPASADOR DE BRAZO MARCADOR BUJE INTER.CORTO(Di=16«)PROL.CILINDRO HI.PASADOR DE HORQUETA P/CORREDERA GRAMPA C/DOBLE CORRED.(COMPR)AMORTI.HORQUILLA TIRA RESORTE COMPRESIONPROLONGACION DE MARCADORES ARANDELA De=47 Di=26 E=5
206121722173218122492295232023222324234023432355235723902359252525303717494866306661670816352030203421942780278131763223
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIPPPPPPPP
ROSCA 7/8" REGISTRO VASTAGO PISTON HID.BASE CONEXION TENSOR RIENDA MARCADORVASTAGO ROSCADO 3/4"RIENDA L=20PLACA DESPLAZ.C/OJO CONEXION RIENDA BUJE CEMENTADO DE AJUSTETORNI 5/16"x3/4" EXA.UNC-ZARANDELA GROWER M- 8
3866415441564168352 L20172354
31323334353637
PPPPPII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
552321
28
416
16
26
21
23
27
24 19
37
22
33
118
313330
1
5
17
20
2214 36
9
6
25 18
1210
30
32
2
13
435
7
1815
1 13
34
17
29
58
MODULES SIDE LINKAGE – TD 21 – 36 AND 48 ROWS
A7029-A-08/2010
GI-GRAMPA 3/4"A=181-LP=165TUERCA UNC 3/4" EXAG=32-ZNIPLE ENG.1/8"GAS-E=9½-RECNIPLE ENGRASE 1/4"SAE-RECTTUERCA UNC 1" EXAG=35-ZTORNI AC G5-5/8"x1.3/4"UNCTORNI AC G5-5/8"x2" UNCTUERCA RW 1/2" EXAG=22-ZTUERCA UNC 5/8" EXAG=24-ZARANDELA GROWER 1/2"ARANDELA GROWER M-16ARANDELA GROWER 3/4"ARANDELA GROWER 1"CHAVETA PARTIDA 5 x 50 -ZTORNI AC G5-1"x 5.1/2" UNCEJE LARGO PARALELOGRAMO CON ENGRASEMEDIA BANCADA DEL SOPORTEPLACA C/BANCADAS SUJECCION PLEGADO PLEGADO CON ROTULA P/TANDEM LATERALPLACA C/PERNO CONEX.ROTULA P/TANDEM TUERCA CASTILLO 1.¬" UNF CON MANGOBAJADA INTERM(26)TIRO LANZA C/HIDRBARRA UNION TRASERA MODULOS
17612172218021812302231923202341234323572359236023622526767721522287309630973098314344705033
123456789
1011121314151617181920212223
IIIIIIIIIIIIIIIPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
16
19
321
4
14
20
8
10
17
1718
911
7
6
11
11
122
22
22
15
135
4
15
135
4
9 11
23
59
REAR CATWALK
A7071-A-06/2010
M-TAPON PLAST.MAZA C/TROMPGI-GRAMPA 5/8"A=178-LP=152TORNI 1/2"x1.3/4"EXAG.RW-ZTORNI AC G5-3/8"x1.1/4"UNCTORNI AC G5-5/8"x2" UNCTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 1/2"ARANDELA GROWER M-16ARANDELA PLANA 3/8" -ZCHAVETA PARTIDA 4 x 40 -ZTUERCA*UNC-5/8"AUTOFRENA-ZTUERCA*UNC-3/8"AUTOFRENA-ZTUERCA*RW-1/2"AUTOFRENAN-ZGI-GRAMPA 1/2"A135-LP190-ZARANDELA De=38 Di=17 E=6 ARANDELA De=35 Di=13,5 E=5 SUJETADOR FINO DE PLATAFOR.DESPL.ESCALERA ANCHA DE PLATAFORMA C/P.SOPORTE DE PLATAFORMA TRASERABARANDA TRAS.SUP.DERECHA TD21x24BARANDA TRAS.SUP.DERECHA TD21x18BARANDA TRAS.SUP.DERECHA TD21x30BARANDA TRAS.SUP.IZQUIER. TD21x24BARANDA TRAS.SUP.IZQUIER. TD21x18BARANDA TRAS.SUP.IZQUIER. TD21x30BARANDA TRAS.INF. C/AGUJ.TD21x24BARANDA TRAS.INF. C/AGUJ.TD21x18BARANDA TRAS.INF. C/AGUJ.TD21x30BARANDA TRAS.INF. C/AGUJ.TD21x30COLUMNA RECTANG.SOPORTE TRASERO
14171760206423132320234123572359237025233717396456115633 331 S 381 G21224053405540594255405940604256406040614232399725504063
123456789
1011121314151617181920
21
22
23
IIIIIIIIIIIIIIPPPPPPPPPPPPPPPP
SUJETADOR GRUESO DE PLATAFORMABASE C/GUIA DE BARANDA INFERIORPLATAFORMA DESPL.L=4200 TD21X24PLATAFORMA DESPL.L=3240 TD21X18PLATAFORMA DESPL.L=1520 TD21X30PLATAFORMA DESPL.L=1300 TD21X30PLAT. DESPL. CUBREMANDOS TD21X30
4064406540664234706772647424
242526
PPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
1414
18
1
22
1010
26
21
20
23
25
19
19
2
1724
25
17
2
2
19
49
17
129
111613
58
15
25
724
3
6
1
24
1585
5
815
60
FERTILIZER BOX AND SEEDS SINGLE BOX
A5028/A5029-A-12/2009
TUERCA UNC 5/8" EXAG=27-ZTORNI AC G5-5/8"x2" UNCARANDELA GROWER M-16PRISIONERO 1/4" x 3/8" RWARANDELA De=38 Di=17 E=6 (ZINCADA) ARANDELA RECTANG.AJUSTE BATORNI TANQUE-1/4" x 3/4"AMORTIGUAD.A GAS Cod.23040CHAVETA PARTIDA 2½x 20 -ZTOLVA TD21x24 LINEAS-SEMILLASTOLVA TD21x18 LINEAS-SEMILLASTOLVA TD21x30 SEMILLAS (PAR)BANDA CURVA(S)24 Ax4677 TD21X24BANDA CURVA(S)16 Ax3477 TD21X30BANDA CURVA(S)16 Ax3102 TD21X30BANDA CURVA(S)18 Ax3507 TD21X18ARANDELA PLANA 5/16"BISE-ZTUERCA*UNC-1/4" FLANGE -ZTOLVA TD21x24 LINEAS-FERTILIZANTETOLVA TD21x18 LINEAS-FERTILIZANTETOLVA TD21x30 LINEAS-FERTILIZANTEBANDA CURVA(F) TD24 Ax4677BANDA CAJON FER. 3102x16 TD21 X 30 L.BANDA CAJON FER. 3477x16 TD21 X 30 L.BANDA CURVA(F) TD18 Ax3507ZARANDA TOLVA TD21X24 LINEASZARANDA TOLVA TD21X18 LINEASZARAND.LARGA TD21 X 30 LINEASZARAND.CORTA TD21 X 30 LINEASM-BOQ.SALI.INCL.BASE CURVA
2171232023596055331 S4121228935754533631663157789640785668567640671757749631963187788640085658564639964196418544454455991
123456789
10
11
121314
15
16
17
IIIIPPIIIIIIIIIIIIIIIIIIIIIIII
S*BOQ.C/CIERRE-DESMONTABLECIERRE PARA BOQUILLA DESMONTABLESOPORTE SUPERIOR GUARDA PLASTICAM-PERILLA C/TORN. 5/16" L=16GUARDA PRFV DEPOSITOSTORNILLO TANQUE 1/4" X 3/4" INOXIDABLE
75687594412829134227808
181920212223
IIPIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
16
16
89
22
21
25
15
1718
2312
12
19
138
2021
52
2 5
1
6
3
8
11
1718
19
7
1212
13
14
10
25
225
5
21
FERTILIZER METER AND OUTLET TUBE
6112/2009
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCIONFUELLE 33 ANILLO 10044-ADRUNION INF. CORR.C/CAÑO DER.M-UNION SUP.FUEL.C/CORR-DEM-CODO GIRAT.45º P/CHEVRONCAÑO CORRUGADO D=32 BAJADA L= 650 TUERCA*UNC-1/4" FLANGE -ZTAPA ANULA BOCA DOSIFICAGRAMPA CHICA P/TAPA SUP.TAPON TAPA SUP.DOSIFICADORTAPA SUP.DOSIF.TURBO T.B.PERNO CORTO DOSIF. TURBOANILLO SEGURID.P/EJE D=4ROTOR ALIM.C.EXAGONAL 1"BUJE DOSIFICADOR C. EXAGONALCARCAZA DOSIFICAD. TURBOTAPA INFER. DOSIFIC. TURBOPERNO LARGO DOSIF. TURBOTORNI. TANQUE 1/4" X 3/4"GRAMPA GRANDE MUELLE DOSIF.
1060356335645758417277495986752261376136613961386143614461356141617322896142
123456789
10111213141516171819
IIIIPIIIIIIIIIIIIII
1
3
5
2
9
117
10
1218
6
15
17
16
1413
14
12
19
4
8
62
SEEDS METER AND OUTLET TUBE
12/2009
FUELLE 33 ANILLO 10044-ADRM-BOQ."Y" DESC.ALFA.MD-DERM-UNION SUP.FUEL.C/CORR-DEM-CODO GIRAT.45º P/CHEVRONM-ADAPT.CHEVR.C/MANGU.D=32CAÑO CORRUGADO D=32 BAJADA L=700CAÑO CORRUGADO D=32 BAJADA L=920TUERCA*UNC-1/4" FLANGE -ZTAPA ANULA BOCA DOSIFICAGRAMPA CHICATAPON TAPA SUP.DOSIFICADORTAPA SUP.DOSIF.TURBO T.B.PERNO CORTO DOSIF. TURBOANILLO SEGURID.P/EJE D=4ROTOR ALIM.C.EXAGONAL 1"BUJE DOSIFICADOR C. EXAGONALCARCAZA DOSIFICAD. TURBOTAPA INFER. DOSIFIC.TURBOPERNO LARGO DOSIF. TURBOTORNI. TANQUE 1/4" X 3/4"GRAMPA GRANDE MUELLE DOSIF.
106035623564575871534170508277495986752261376136613961386143614461356141617322896142
123456789
101112131415161718192021
IIIIIPPIIIIIIIIIIIIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
10
11
13
12
9
5
4
1
3
2
76
191816
15
16
17
8
20
21
14
14
A7059-A-06/2010TUERCA UNC 3/8" EXAG=16-ZPRISIONERO 3/8"x1/2" RW-ZTORNI AC G5-3/8"x1" UNCARANDELA GROWER 3/8"ARANDELA PLANA 3/8" -ZARANDELA CAJA RODAM.ALIMENT.E INT.ENGR. Z 14 x 1/2" DEL INTERMEDIARIO CAJA RODAM.TRAN.INTER.ABON.y ALIM EJE INTERME.TRANSMISION SEMILLAS ENGR.Z14 y Z47x1/2" INTERMED.SEMILLA
5152167219423092355237030853136354350865087
123456789
1011
IIIIIIPPPPP
63
COUNTERSHAFT FOR CHEVRON WHEEL-TYPE METER TD
A7059-A-06/2010
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
52
3
11
1
9
6
4
10
8
7
3
1
64
TRANSMISSION: FERTILIZER BOX END DRIVE
A5025-A-06/2010
RODAMIENTO 6006 RS2CADENA DE RODILLOS ASA 40UNION P/CADENA ASA 40ARO*SEEGER 55x2 P/CILINDTUERCA UNC 3/8" EXAG=16-ZPRISIONERO 3/8"x1/2" RW-ZTORNI AC G5-3/8"x1" UNCTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA PLANA 3/8" -ZARANDELA PLANA 1/2" -ZCHAVETA PARTIDA 3 x 25 -ZARO SEEGER 11 x 1 P/EJEARO SEEGER 30 x 1,5 P/EJERODAMIENTO 6201 RS2TORNI 3/8"x3.1/4"EXA.UNC-ZARANDELA De=35 Di=13½ E=5 (ZINCADA)RODILLO TENSOR CADENAENGR. Z 14 x 1/2" DEL INTERMEDIARIO C.FERT.TUBO 21x14 L=37 FIJ.SOP.SUPER.GUARDA ENGR. Z 40 x 1/2" ARRASTREBUJE DE ENGR.Z=40 ARRASTREVARILLA EXAGONAL DISTRIB.CAJ.TD21 X 18VARILLA EXAGONAL DISTRIB.CAJ.TD21 X 24VARILLA EXAG.DIST.(DER)CAJON FER.TD30VARILLA EXAG.DIST. (IZQ)CAJON FER.TD30 ENGR.Z 14 y Z 35 x 1/2" INTERMEDIARIOEJE DE ENGRANAJE INTERMEDIARIO
5781130115019852167219423092341235523572370237225202560256266066737381 G46093136395941024103443041047056705741054106
123456789
101112131415161718192021222324
2526
IIIIIIIIIIIIIIIIIPIPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
24
15
4
1
22
13
13
23
20
6
2
3
5
95
9
1416
25
59
21
19
11
1716
26
1812
10 8
7
7
65
TRANSMISSION: GENERAL SOWING DRIVE WITH GEARBOX
A5143-A-08/2010
RODAMIENTO 6006 RS2CADENA DE RODILLOS ASA 50MEDIA MALLA ASA 50GI-GRAMPA 5/8"A=178-LP=152TORNI 1/4"x1" UNC-TOTAL-ZTORNI 5/16x1.3/4"EXA.UNC-ZTORNI 1/2"x1" EXAG.RW-ZTUERCA UNC 3/8" EXAG=16-ZPRISIONERO 3/8"x1/2" RW-ZPRISIONERO 3/8"x3/4" RWPRISIONERO 3/8"x1" RWCONTRATU.3/8"UNC EXAG=14-ZTORNI AC G5-3/8"x1.1/4"UNCARANDELA GROWER 1/4"ARANDELA GROWER M- 8ARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA PLANA 3/8" -ZCONTRATU.3/4"NF E=32 A=7-ZGAR-CAJA VEL.IZQ.SEMILL.MDTUERCA*UNC-5/8"AUTOFRENA-ZTUERCA*UNC-3/8"AUTOFRENA-ZRESORT Nº29-A De=32x58 COMTUERCA UNC 5/16" EXAG=12-ZTORNI 3/8"x3.1/4"EXA.UNC-ZM-PERILLA C/TUERCA 1/4" WCONTRATU.3/4"NF E=27 A=8-ZBUJE TRABA EJE CAJA VEL.P/PASADORARANDELA De=44 Di=26 E=3 EJE D=25CHAVETA PLANA 5/16" L= 45
57811311161176020042022206121672194219521962244231323532354235523572370337635203717396443066708673767816791 367 R 919 B 920 B
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIIIIIIPPP
ARANDELA De=39 Di=20,6 E=2CAJA ROD.SOPORTE PUNTA EJE MOTRIZSUJETADOR FINO DE PLATAFORMA RODILLO APRET.EXCENT.LISO TENSOR ARANDELA De=35 Di=13,5 E=5 CHAVETA PLANA 1/4" L= 50ENGR. Z 16 x 5/8" C/MUESCAS P/SAFEMAZA DE SAFE C/MUESCASMANGUITO PORTA RODAMIENTO EJE ENGR.Z 26 y Z40x5/8" EJE MOTRIZ ALTAENGR. Z 20x5/8" DE CAJA VELOCIDAD GUARDA CADENA TRANSM.CENTR.CAJASOPORTE GUARDA CADENA TRANSM.BASE CAJA CAMBIOS DE VELOCIDADSOPORTE DERECHO PATIN APRETADOR PLEGADO SOPORTE IZQU. EJE MOTRIZ EJE MOTRIZ TRANS.P/SIEMBRA TD21X24EJE MOTRIZ TRANS.P/SIEMBRA TD21X18GI-GRAMPA 5/8"A=138-LP=190TORNI 3/8"x1.1/2"EXA.UNC-ZBAJADA SOP. PUNTA EJE MOTRIZ-IZQU. BUJE De=21 Di=14 L= 7 ARANDELA De=32 Di=10 E=5 ZINCADAM-RODILLO TENSOR DE CADENASOP.PATIN APRET.CADENA MOD.INDIVID.SOP.PATIN APRET.CADENA MOD.ADICIO.
921 B211021222365276231453391339340894093409843624363501550165023503850431762203526551445 R2238460950145049
3132333435363738394041424344454647
48495051525354
PPPPPPPPPPPPPPPPPPIIPPPIPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
46
1
1
23
26
13
1822
99
13
13
9
23
2719
37
24
6
15
2928
29
20
4
4
4
71735
21
44
10 30
112153
53 19
21
21
18 16
8
18
168
47
39
39
39
49
16
8
42
4333
32
32
32
50
48
5241
36 46
45
40
38
1211
2534 5
51
31
14
25
21 16
8
54
66
TRANSMISSION: GENERAL FERTILIZING DRIVE WITH GEARBOX
A5144-A-08/2010
RODAMIENTO 6006 RS2CADENA DE RODILLOS ASA 50MEDIA MALLA ASA 50GI-GRAMPA 5/8"A=178-LP=152TORNI 1/4"x1" UNC-TOTAL-ZTORNI 5/16x1.3/4"EXA.UNC-ZTORNI 3/8"x2.1/2"EXA.UNC-ZTORNI 1/2"x1" EXAG.RW-ZTUERCA UNC 3/8" EXAG=16-ZPRISIONERO 3/8"x1/2" RW-ZPRISIONERO 3/8"x3/4" RWPRISIONERO 3/8"x1" RWCONTRATU.3/8"UNC EXAG=14-ZTORNI AC G5-3/8"x1.1/4"UNCARANDELA GROWER 1/4"ARANDELA GROWER M- 8ARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA PLANA 3/8" -ZCONTRATU.3/4"NF E=32 A=7-ZTUERCA*UNC-5/8"AUTOFRENA-ZGAR-CAJA VEL.DERECH.MIX/MDRESORT Nº29-A De=32x58 COMTUERCA UNC 5/16" EXAG=12-ZM-PERILLA C/TUERCA 1/4" WCONTRATU.3/4"NF E=27 A=8-ZBUJE De=21 Di=14 L=22CHAVETA PLANA 5/16" L= 30BUJE TRABA EJE CAJA VELOC.P/PASADORARANDELA De=44 Di=26 E=3 EJE D=25
5781131116117602004202220392061216721942195219622442313235323542355235723703376371740414306670867816791326 H345 J367 R919 B
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIIIIIPPPP
ARANDELA De=39 Di=20,6 E=2COLLAR TRABA D=22,5 C/PRISIONEROCAJA RODAM.SOPORTE PUNTA EJE MOTRIZARANDELA De=35 Di=13« E=5 (ZINCADA)CHAVETA PLANA 1/4" L= 50ENGR. Z 16 x 5/8" C/MUESCAS P/SAFEMAZA DE SAFE C/MUESCASMANGUITO PORTA RODAMIENTO EJE MOTRIZENGR.Z 20 y Z 40 x 5/8" EJE MOTRIZ ALTAENGR. Z 20 x 5/8" DE CAJA VELOCIDAD P/F.ANILLO SEPAR.42x26x18 ENGR.CAJA GUARDA CADENA TRANSM.CENTRAL CAJA ANGULO SOPORTE GUARDA CAJA FERTIL.BASE CAJA CAMBIOS DE VELOCIDADSOPORTE IZQUIER.PATIN APRET. CADENAPLEGADO SOPORTE IZQUIERDO EJE MOTRIZ EJE MOTRIZ DE TRANSMISION P/FERTI.TDX24 EJE MOTRIZ DE TRANSMISION P/FERTI.TDX18 RODILLO APRET.CENTRADO C/GUIA CENTRAL
921 B1455 H21102762314533913393408940964098411241394140501550175023503950447411
3132333435363738394041424344454647
48
PPPPPPPPPPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
47
91719
46
133
38 10
39
14
23
42
35
52543
748
27
45
19
179
25
2620
23
3637
1213
30 2922
6
28
40
4131
32
16
2444
4
4
2134
188
10
15
11
67
ROW UNIT ANCHOR
A7001-A-12/2010
TORNI 1/2"x1" EXAG.RW-ZTORNI AC G5-5/8"x3.1/4"UNCTUERCA UNC 5/8" EXAG=27-ZTORNI AC G5-5/8"x2" UNCTORNI AC G5-5/8"x2.1/4"UNCRES*CLAV.P/PALETA REMOVE-ZARANDELA GROWER M-16ARANDELA PLANA 5/8"E=3,2-ZTUERCA*UNC-5/8"AUTOFRENA-ZRESOR A8-De=51 L=220 EXPANBUJE TRATADO C/TOPE P/BRAZOS CUER.BUJE CEMENTADO ANTIFRICCION P/CUER.BRAZO SUPERIOR DE CUERPOSBRAZO INFERIOR DE CUERPOS C/CONEX.EJE REGISTRO TENSION RESORTE CUER.GUSANO C/OJO D=20 TENSOR RESORTEGUSANO C/OJO D=23 TENSOR RESORTE BUJE TOPE PARAL.SUPERIOR CONEX.RE.GRAMPA MAYOR ANCLAJE Y CONEX.BR.GRAMPA MENOR ANCLAJE Y CONEX.BR.PLACA TOPE BRAZO DE CUERPO SUPER. PLACA TOPE BRAZO CUERPO SUPERIOR
2061865021712320232144182359237437174238320943995001500250035004500550105077507850887430
123456789
101112131415161718192021
IIIIIIIIIIPPPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
5
5
4
11
13
37
812
128
7
3
4
11
19
20 16
10
17
98
1812
8 18
12
17
9
1015
1
3
8
712
16
11
4
143
7
812
4
8
12
117
48
1211
37
9
3
2
2 11
11
55
1
6
21
68
OPENER DISK
A7002-A-05/2010
TUERCA UNC 3/16" E=8 A=4-ZTORNI TANQUE*3/16"x 1/2"ARANDELA GROWER M- 8RES.TRABA Y SUJEC.CAÑO BAJADAARANDELA PLANA 3/16"-ZARANDELA PLANA 3/8" -ZARANDELA PLANA 1/2" -ZTUERCA*UNC-3/8"AUTOFRENA-ZM-CAÑO PLAST.BAJ.FERTIL.TDM-CAÑO PLAST.BAJ.SEMILL.TDRESOR A2-De15,7 L=111 EX-ZRES.MUELLE LIMP.DISC.CONICRES.MUELLE SUJECC. TUBO TDTUERCA UNC 5/16" EXAG=12-ZCONTRATU.1/2"W-12H"EX=19-ZTUERCA UNC 1/4"E=11 A=5½-ZSUJETADOR Y REGISTRO MUELLE LIMPIA.EJE RECAMBIABLE DE RUEDA NIVELADO.CAÑO GUIA MANG.C/TOR.5/16"x 1.1/4CHASIS CUERPO INTEGRAL PLANT.TDTORNI TANQUE-1/4" x 3/4" ARANDELA PLANA 1/4"BISEL-ZARANDELA GROWER 1/4"
18522269235439222367237023723964465746585984629863846708703321653881392050465091228934372353
123456789
1011121314151617181920212223
IIIIIIIIIIIIIIIIPPPPIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
1019
20 18
11
157
21
4
22
2316
17
1218
9
1
5
13
2
14
3
68
14
69
CONICAL STAMPED, 15.5”COULTER BLADE W/HUB
A9281-A-05/2010
RODAMIENTO 30204TORNI AC G5-3/8"x3/4" UNCTORNI AC G5-3/8x3/4-R.IZQUIERDA-UNCREMACHE 5/16"x3/4" CRARANDELA AJUSTE 20x28x0,5M-TAPA PLASTICA P/MAZASDISCO PLANO 15½"2ES(1F)5mmARANDELA AJUSTE 20x28x0,2RESO.ANILLO SEGURI.55x3 -ZRETEN SAV 10890/DBH 9217ARANDELA AJUSTE 20x28x0,8BUJE GUIA RODAMIENTO D.DOBLEMAZA DE CUCHILLA PLANTADOR CIP BUJE PORTA RETEN C/RESPALDO
5612312241624874600539965236747694169947614321639684190
123456789
1011121314
IIIIIIIIIIIPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
9
6
212
1
8
5
4
7
13
111
10
14
3
70
ASSEMBLED GAUGE WHEEL – 2.3/4” X 15”
A7004-A-05/2009
RODAMIENTO 30204TORNI 5/16"x3/4" EXA.UNC-ZTORNI AC G5-3/8"x1" UNCARANDELA GROWER M- 8ARANDELA_ABANICO EXT*A-8,4M-TAPA PLASTICA P/MAZASCUB.SEMI.2"3/4"x15"NIV.CIPTUERCA UNC 5/16" EXAG=12-ZARANDELA AJUSTE 20x28x0,2RESO.ANILLO SEGURI.55x3 -ZRETEN SAV 10890/DBH 9217TORNI AC G5-5/16"x5/8" UNCARANDELA AJUSTE 20x28x0,8SEMILLANTA TAPA DE RUEDA NIVELADORASEMILLANTA ANGOSTA(SAE15B30)R.NIV.BUJE GUIA RODAMIENTO D.DOBLEMAZA DE RUEDA NIVELADORA TDTORNI 5/16x2.1/2"EXA.UNC-ZTORNI 1/2"x3" EXAG.RW-ZNIPLE ENGRASE 1/4"SAE-RECTOTUERCA RW 1/2" EXAG=22-ZARANDELA GROWER 1/2"ARANDELA PLANA 1/2" -ZARANDELA AJUSTE 13x21x0,2TUERCA*UNC-5/16"AUTOFREN-ZARANDELA_MTA AN 34½x28x0,4O RING DBH 52-317LEVA INTERMED.REGULACION R.NIVELADORATORNILLO REGISTRO R.NIVELADORA.BALANCIN OSCILATORIO TOPE R.NIVELADORA
561201723092354239053995943670867476941699471607614268927253216501220252069218123412357237240174151482776061404 R1409 R1422 R
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIPPPPIIIIIIIIIIPPP
TORNILLO 1/2" x 3/4" RW SUJECC.Y LUBRICA.ARANDELA De=38« Di=25,6 E=3ARANDELA De=38« Di=25,6 E=2GUARDAPOLVO DEL BRAZO RUEDA NIVELA.LIMPIADOR RUEDA NIVELADORA TDBUJE DE LEVA REGISTRO RUEDA NIVELA.GUARDAPOLVO DELANTERO DE BALANCINARANDELA De=24 Di=14 E=1,6 BALANCIN FUNDIDO RUEDA NIVELADORA
1427 R1433 R1463 R1468 R26983894403840435026
313233343536373839
PPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
2034
26
31
301936
2123
3624
29
6
316 1
9
2
17 14
127
15
4 8
31
8
13
111
2739
25
18
35
3332
2237 38
28
38
22
20
5
10
71
CLOSING DISK SET RIM – 14”
A7047-A-05/2010
RODAMIENTO 30204TORNI AC G5-3/8"x1" UNCREMACHE 5/16"x3/4" CRM-TAPA PLASTICA P/MAZASDISCO LLANTA DENT.14"ESTAMARANDELA AJUSTE 20x28x0,2RESO.ANILLO SEGURI.55x3 -ZRETEN SAV 10890/DBH 9217ARANDELA AJUSTE 20x28x0,8GUARDAPOLVO DE MAZA RUEDASBUJE GUIA RODAMIENTO D.DOBLEBUJE PORTA RETEN C/RESPALDO DE EJE MAZA DE RUEDA NIVELADORA TDRODAMIENTO 30204REMACHE 5/16"x3/4" CRDISCO LLANTA DENT.14"ESTAMARANDELA AJUSTE 20x28x0,2RETEN SAV 10890/DBH 9217ARANDELA AJUSTE 20x28x0,8GUARDAPOLVO DE MAZA RUEDASMAZA DE RUEDA NIVELADORA MD21BUJE PORTA RETEN C/RESPALDO DE EJEEJE ADICION.(R.DER)RUEDA CAMELLON ARANDELA De=56,7Di=20,2 E=2,5 (ZINCADA)TORNI 1/2"x1.3/4"EXAG.RW-ZTORNI AC G5-3/8"x1" UNCTUERCA UNC 3/8" EXAG=14-ZARANDELA GROWER 3/8"ARANDELA PLANA 3/8" -ZARANDELA PLANA 1/2" -Z
561230924875399543867476941699476141485 J321641905012561248754386747699476141485 J4187419050675106206423092340235523702372
123456789
101112131415161718192021222324252627282930
IIIIIIIIIPPPPIIIIIIPPPPPIIIIII
TUERCA*UNC-3/8"AUTOFRENA-ZTORNI CR/CC_1/2x1.1/4"RW-ZTUERCA*RW-1/2"AUTOFRENAN-ZTORNILLO 3/8"x4" ENGANCHE RESORTE CAJA POSICIONADORA P/REGISTRO RUEDAPALANCA C/MANOPLA REGISTRO RUEDABUJE TOPE BRAZO DOBLE P/RUEDA RESORTE CONICO D=34 L=190 RUEDA CAME.EJE C/REGI.SIMPLE/DOBLE R.CAMELLON
396440285611270538843918402150285066
313233343536373839
IIIPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
23
2422
18
14
21
19
15
1617
14
20
18
22
1012
81
95
13
36
111
24
7
38
39
34
25
30
30
25
36
3337
35
26
26
33
3332 30
27
2831
33
32
2626
30
37
28
29
72
SEED FIRMING SKID
A6302-A-05/2010
TUERCA UNC 1/4"E=11 A=5½-ZARANDELA GROWER 1/4"ARAND*PLANA P/TORNI.M 6 -ZTORNI TIRAF.EX.¼x1.½"R.TOTTORNI 1/4"x1¼" UNC-TOTAL-ZTUERCA*UNC-1/4"AUTOFRENA-ZPATIN AFIRMADOR(PLASTICO)C/REGIS.
2165235323684125414941504400
1234567
IIIIIIP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
52
1
4
36
7
73
PRESS WHEEL - 1”X8” (OPTIONAL ITEM)
A9280-A-07/2010
CUB.SEMINEUMAT.1"x 8" CUADR.TORNI 1/2"x3.1/4"EXAG.RW-ZNIPLE ENGRASE 1/4"SAE-RECTOTUERCA RW 1/2" EXAG=22-ZCONTRATU.5/16"UNC EXA=12-ZARANDELA PLANA 5/16"-ZRESOR A3-De=20 L=60 EXPAN.TORNI AC G5-5/16"x7/8" UNCRESOR A2½-De=15 L=25 COM-ZTORNI AC G5-5/16x1.1/2"UNCCONTRATU.1/2"W-12H"EX=19-ZBUJE OSCILACION HORQUETA RUEDA.BRAZO CONEXION REGISTRO R.APRET.HORQUILLA FLOTANTE RUEDA APRET.BUJE DE BRAZO CONEXION RUEDA.TORNILLO 1/2" RW L=65 CAB=6mm REGISTRO DE RUEDA APRETADORA CIPTORNI 5/16"x3/4" EXA.UNC-ZTUERCA UNC 5/16" EXAG=12-ZARANDELA PLANA 5/16"-Z M-SEMILLAN. 8" NYLON AGUJ.M-EJE P/RUEDA APRET.1"x 8"RODAMIENTO 6203 RS2 RETEN SAV/DBH 5088
365720702181234123452369459847584921494870331419 R26112612265826707195201767082369258925915352588
123456789
101112131415161718192021222425
IIIIIIIIIIIPPPPPPIIIIIII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
1
22
21 2524
18 20
21
25 2419
17
13
59
11
10
16
2
12
144
7
86
15
3
5
74
FRONT 16” COULTER BLADE UNIT W/ ANCHORING SET
A7058-A-05/2010
RODAMIENTO 30206TORNI AC G5-3/8"x1.1/4"UNCTUERCA UNC 3/8" EXAG=14-ZARANDELA GROWER 3/8"CUCHILLA 16"TURBO 30-6 REDARANDELA AJUSTE 31x39x0,2RETEN PIEROBON 30-70/72-15MAZA DE CUCHILLA R.FLOTANTE-MACHOMAZA DE CUCHILLA R.FLOTANTE-HEMBRAEJE DE CUCHILLA RECTA FLOTANTE P/MAZA TORNI 5/16"x3/4" EXA.UNC-ZTORNI 5/8"x5.1/2"EXA.UNC-ZTUERCA UNC 5/8" EXAG=27-ZTORNI AC G5-5/8"x4.1/2"UNCARANDELA GROWER M- 8ARANDELA GROWER M-16TUERCA*UNC-5/8"AUTOFRENA-ZGI-GRAMPA TRIA.5/8"D=265-ZPASADOR CIERRE RAPID.3/8"ZRESOR A10-De=51 L=147 CO-PTUERCA UNC 5/16" EXAG=12-ZARANDELA TOPE DE RESORTE CUCHILLASOPORTE Y GUIA EXTERIOR CUERPO CUCHILL.ANILLO SEPAR.42x30x11,5 SOP.CUCH.FLOT.BUJE TRATADO C/TOPE P/BRAZOS DE CUERPOBUJE CEMENTADO ANTIFRICCION P/CUERPOSEMBOLO DEL RESORTE CUCHILLA RECTAHORQUILLA SOPORTE CUCHILLA RECTA GUARDA DE CUCHILLA CORTE DELANTEROBARRA REDONDA P/CUCH.RECTA FLOTANTE
56323132340235561756714676834433444344520172103217122852354235937176484650766616708348 L27063009320943995007500950545076
123456789
101112131415161718192021222324252627282930
IIIIIIIPPPIIIIIIIIIIIPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
24
7
1
6
102
8 5
9
24
16
3
4
7
29
27
2022
14
12
2825
26
2625
1613
30
17
22
20
27
1316
18
18
19
23
17
21
15
11
17
HYDRAULICALLY OPERATED DRYING FAN (OPTIONAL ITEM)
75A5135-A-11/2010
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCIONRODAMIENTO 6006 RS2GI-GRAMPA 5/8"A=178-LP=152CAÑO.PVC CRISTAL 28 x 22ARO*SEEGER 55x2 P/CILINDTUERCA UNC 5/8" EXAG=27-ZTORNI AC G5-3/8"x1" UNCARANDELA GROWER 3/8"ARANDELA GROWER M-16ARO SEEGER 30 x 1,5 P/EJEM-BOQ."Y"SECADO FERT.S/ROSP*¬ROTOR BAL.TURB.SOPL.S/MTUERCA*UNC-1/4"AUTOFRENA-ZTORNI 1/4"x4" EXA.UNC-ZP*¬RADIADOR ACEITE TURBINAV-MOTOR HID(EST)1MOD.M.COR.V-MOTOR HID(EST) TD21X30V-MOTOR HID(EST) TD21X36V-MOTOR HID(EST) TD21X48V-MAZA ESTRIADA TURB.SECADOJO CONEXION SOPORTE MANGUERAGUIA PARA MANGUERASCAJA PORTA MAZA DE TURBINA SECADOTUBO APOYO LONGI.MANGUE. TD21X18 LIN.TUBO APOYO LONGI.MANGUE. TD21X24 LIN.RIENDA DE TUBO APOYO(SUP.)MAN.ALF.SOPORTE C/PERNO DESCANSO BOMBA HID.SOPORTE LARGO C/PERNO DESCANSO BOMBAGRAMPA 5/8"C/BASE SOP. DEP.ACEITE
578176018511985217123092355235925623959413341504298429945195461506645294532372 L1499 A2584412442424125428673254287
123456789
101112131415
1617181920
2122
23
IIIIIIIIIIIIIIIIIIIPPPPPPPPP
DIVISOR 18 SALI.D=21 TURBINA SECADO DIVISOR 24 SALI.D=21 TURBINA SECADODIVISOR 30 SALI.D=21 TURBINA SECADODIVISOR 36 SALI.D=21 TURBINA SECADOSOPORTE DE BARRA GUIA CAÑO MANGU.SOPORTE GENERAL TURBINA BANDA SEPARADORA TURBINA DE SEC.LATERAL DE CAJA TURBINA DE SECADOTAPA DE CAJA TURBINA DE SECADOANILLO SEP.20x8,5x11 RAD.TURB.SECADOARANDELA FIJACION MAZA DE TURBINA TOPE ANTIGIRO BOMBA HIDR.P/1 MOD.MULTIPLICADOR S/NDEPOSITO DE ACEITE 450 X 320 X 190FILTRO DE ACEITE 70 LITROSBASE DE FILTRO SIMPLECODO ENT./SAL. MOTOR Y BOMBATORNI.1/2" X 2" EXAG. RWZCONTRATUERCA 1/2" 12-H EX=19-ZADAPTADOR 1/2 NPT 7/8" JICSOPORTE BASE TURB.Y BIS.UN.MOD.TD 36
429042894348506243144324433143324333436643674404582357705860576757652065703346885064
24
2526272829303132333435363738394041
PPPPPPPPPPPPIIIIIIIIP
35
2233
2
32
2831
1116
27
29
14
30
12
20
17
1810
3
26
2
37
15671
14
3113
24
5
216
4025
3938
3839
36
34
23
6
7
37
9
5
8
5
8
19
41
76
HYDRAULIC JACK
A3-A-05/2010
GATO HIDRAULICO31 AN˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
1
M-TAPON PLAST.MAZA C/TROMPGI-GRAMPA 5/8"A=178-LP=152TORNI 1/2"x1.3/4"EXAG.RW-ZTORNI 5/8"x1.1/2"EXA.UNC-ZTORNI AC G5-3/8"x1.1/4"UNCTORNI AC G5-5/8"x2" UNCTUERCA RW 1/2" EXAG=22-ZTUERCA UNC 5/8" EXAG=24-ZARANDELA GROWER 1/2"ARANDELA GROWER M-16ARANDELA PLANA 3/8" -ZCHAVETA PARTIDA 4 x 30 -ZTUERCA*UNC-5/8"AUTOFRENA-ZTUERCA*UNC-3/8"AUTOFRENA-ZARANDELA De=38 Di=17 E=6 (ZINCADA)SUJETADOR FINO DE PLATAFORMA DESPLAZ.ESCALERA ANGOSTA PLATAF.C/PASAMANOSUJETADOR GRUESO DE PLATAFORMABASE C/GUIA DE BARANDA INFERIORPLATAFORMA DES. L=5000 DELANT.TD-21x24PLATAFORMA DES. L=3740 DELANT.TD-21x18 SOPORTE DE PLATAFORMA DELANTERA ALF.COLUMNA RECTANG.SOPORTE DELANTERO BARANDA DELANT.INF.C/AG.TD21x24 C/ALF.BARANDA DELANT.INF.C/AG.TD21x18 C/ALF. BARANDA DELANT.SUP.DER.TD21x24 C/ALF.BARANDA DELANT.SUP.DER.TD21x18 C/ALF.BARANDA DELANT.SUP.IZQ.TD21x24 C/ALF.BARANDA DELANT.SUP.IZQ.TD21x18 C/ALF.
14171760206420912313232023412343235723592370252337173964331 S21224054406440654067422940684069407042274072422540734226
123456789
1011121314151617181920
212223
24
25
IIIIIIIIIIIIIIPPPPPPPPPPPPPPP
77
FRONT CATWALK FOR LUCERNE BOX (OPTIONAL ITEM)
A7073-A-09/2010
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
1
25
24
22
20
23
16
5
8
17
19
7
9
46
1015
4
9
11
14
12
16
6
10
15
19
18
18
21
2
13
61015
1
18
78
LUCERNE BOX ASSEMBLY (OPTIONAL ITEM)
A7008-A-09/2010
CADENA DE RODILLOS ASA 40UNION P/CADENA ASA 40TORNI 5/16"x1" EXA.UNC-ZTORNI 3/8"x2.1/2"EXA.UNC-ZTORNI 1/2"x2" EXAG.RW-ZTUERCA UNC 3/8" EXAG=16-ZNIPLE ENGRASE 1/4"SAE-RECTPRISIONERO 5/16"x1/2" RWPRISIONERO 3/8"x1/2" RW-ZTORNI AC G5-3/8"x1" UNCTORNI AC G5-3/8"x1.1/4"UNCARANDELA GROWER 3/8"ARANDELA PLANA 5/16"-ZARANDELA PLANA 3/8" -ZARO SEEGER 30 x 1,5 P/EJEMON-DEPOS.ALFA. TD21x18 PARMON-DEPOS.ALFA. TD21x24 PARMON-DEPOS.ALFA. TD21x30-PARTORNI AC G5-5/16x1.1/2"UNCPRISIONERO 1/4" x 3/8" RWM-BUJE MICARTA EJE ALFALF.CONTRATU.1/2"W-12H"EX=19-ZENGR. Z 24 x 1/2" MANDO VAR.# 5/16"ALIMEN.BUJE De=21 Di=14 L=22BUJE DE ENGRANAJE MANDOBUJE TRABA EJE MANDO ALFALFEROBUJE TRABA VARILLAS # 5/16"ALIMENT.ALF.ENGR. Z 14 x 1/2" DEL INTERMEDIARIO SOPORTE LATERAL DERECHO DE CAJON ALF.SOPORTE LAT. DERECHO CAJON ALF.TD21x30
1130115020192039206521672181219221942309231323552369237025623833343178334948605569597033302 W326 H345 K370 W2361313641134485
123456789
10111213141516
1718192021222324252627
IIIIIIIIIIIIIIIIIIIIIIPPPPPPPP
SOPORTE LATERAL IZQUIERDO CAJON ALF.SOPORTE LAT. IZQUIER.CAJON ALF.TD21x30SOPORTE DOBLE CENTRAL DE CAJON ALF.ESCUADRA SOP.CENTRAL CAJON TD21x30 RODILLO APRET.EXCENTRICO C/GUIA CEN.VARILLA CUADRADA CAJON ALF. TD21x24VARILLA CUADRADA CAJON ALF. TD21x18VARILLA CUADRADA ALF.LARGA TD21X30VARILLA CUADRADA ALF.CORTA TD21X30 EJE MOTRIZ MANDO CENTRAL ALF. TD21x24EJE MOTRIZ MANDO CENTRAL ALF. TD21x18EJE MOTRIZ MANDO CENTRAL ALF. TD21x30 SUPLEMENTO CAJA CENTRAL MANDO TUBO APOYO LONGITUDINAL MANGUERAS RIENDA DE TUBO APOYO(SUPERIOR)MANGU.RIENDA DE TUBO APOYO(INFERIOR)MANGU.ARANDELA De=22 Di=10 E=6 SUPL.ALFAL.ENGR.Z 35 y Z 22 x 1/2" TRANSM.ALFALFEROENGR. Z 12 x 1/2" TRANSMISION ALFALFERORODILLO APRET.CENTRADO C/GUIA CENTRAL
41144486411544874116411742407108710941184241510541194124412541264127441144127411
28
29
3031
32
3334353637383940
PPPPPPPPPPPPPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
16
37
37
12
14
1114126
27
14
6
205
34
126
36
351014
29
1924
8
32
38
3030
1
26
20
5
28
37
21331317
119
14
7
12
19
624
8
31
31
18
25
10
14
23 15
1014
3 414
40
398
2214
6
7
2
79
TRANSMISSION: FERTILIZER GEARBOX (OPTIONAL ITEM)
A7009-A-09/2010
RODAMIENTO 6005 RS2CADENA DE RODILLOS ASA 40UNION P/CADENA ASA 40GI-GRAMPA 5/8"A=178-LP=152TORNI 1/4"x1" UNC-TOTAL-ZTORNI 5/16x1.3/4"EXA.UNC-ZTORNI 1/2"x1" EXAG.RW-ZTUERCA UNC 3/8" EXAG=16-ZPRISIONERO 3/8"x1" RWCONTRATU.3/8"UNC EXAG=14-ZTORNI AC G5-3/8"x1" UNCARANDELA GROWER 1/4"ARANDELA GROWER M- 8ARANDELA GROWER 3/8"ARANDELA GROWER 1/2"ARANDELA PLANA 3/8" -ZCONTRATU.3/4"NF E=32 A=7-ZTUERCA*UNC-5/8"AUTOFRENA-ZCAJA DE VELOCIDAD - DERECHARESOR A5-De=32 L=31 COMPR.TUERCA UNC 5/16" EXAG=12-ZM-PERILLA C/TUERCA 1/4" WCONTRATU.3/4"NF E=27 A=8-ZBUJE TRABA EJE CAJA VELOC.P/PASADORCHAVETA PLANA 5/16" L= 40ARANDELA De=44 Di=26 E=3 EJE D=25 ARANDELA De=39 Di=20,6 E=2ESCUADRA SOPORTE GUARDAARANDELA De=35 Di=13,5 E=5 (ZINCADA)EJE INTERMEDIARIO TRANSMISION ABONADOR
5151130115017602004202220612167219622442309235323542355235723703376371740415629670867816791367 R382 W919 B921 B261727623067
123456789
101112131415161718192021222324252627282930
IIIIIIIIIIIIIIIIIIIIIIIPPPPPPP
ARANDELA CAJA RODAM.ALIMENT.E INTERME.ENGR. Z 47 x 1/2" P/BAJA DENSIDAD ABONOMAZA DE SAFE C/MUESCASENGR.Z 12 y Z 19 x 1/2"C/SAFE MUESCASCAJA RODAM.TRAN.INTERM.ABON.y ALIM GUARDA CADENA TRANSM.CENTR.CAJA ALF.SOPORTE GUARDA CADENA CAJA ALF.(IZQ).BASE CAJA CAMBIOS DE VELOCIDADTUBO TRANSMISION CAJA FERTIL.P/ALF.TD-21
308532373393339735434141437350155032
313233343536373839
PPPPPPPPP
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
32
11
16
23
35
30
14
81
131
28
36
24
26
23
17
203433
27
3722 12
59
10
26
25
39
6
1321
4
4
7
15
2918
38
19
80
LUCERNE METER (OPTIONAL ITEM)
A9148-A-09/2010
TORNI TANQUE-1/4" x 1/2"TUERCA*UNC-1/4" FLANGE -ZTORNI ATER.Nº 4x 9,5-C/FIJRODILLO FIJO LISO CIERRE ALIMENTADORCAJA ALIMENTADOR FIJO ALFALFEROTAPA ALIMENTADOR FIJO ALFALFEROFUELLE ALFALFERO-C/POLLER.RES.GRAMPA SUJECCION P/M28M-CODO DE GOMA P/ALFALFEROBOQUILLA D=22 UNION CAÑOS ALFALFEROTAPA ANULADORA SIEMBRA ALIMENTADOR MANGUERA BAJADA CUERPO TRASER.L=890MANGUERA BAJADA CUERPO DELANT.L=1300MANG.BAJADA CUERPO DELANT.TD30 L=1400CAÑO DESCARGA ALF..EXTERNO C/OJO SUJ.CAÑO CURVO DESCARGA ALF.C/OJO SUJ. TORNI 1/2"x1" EXAG.RW-ZTUERCA RW 1/2" EXAG=22-Z
500177492231235823592360106462436375408641675035509373545090711720612341
123456789
101112
13141516
IIIPPPIIIPPPPPPPII
N˚ CODIGO DESCRIPCION N˚ CODIGO DESCRIPCION
7
12
11
6
5
4
9
1
2
3
10 16
15
14
13
8