FFFLLLUUUIIIDDD MMMEEECCCHHHAAANNNIIICCCSSS AAANNNDDDHHHYYYDDDRRRAAAUUULLLIIICCC MMMAAACCCHHHIIINNNEEESSS
LAB MANUAL
GUDLAVALLERU ENGINEERING COLLEGE FUELS & LUBRICANTS LAB
INDEX
S.NO. NAME OF THE EXPERIMENT PAGE NO
1 REDWOOD VISCOMETER-I 1-5
2 REDWOOD VISCOMETER-II 6-10
3 ENGELRS VISCOMETER 11-15
4 SAYBOLT VISCOMETER 16-20
5 CLEVELANDS FLASH & FIRE POINT TEST 21-24
6 PENSKY MARTEN FLASH & FIRE POINT TEST 25-28
7 ABELS FLASH AND FIRE POINT 29-32
8 CARBON RESIDUE TEST 33-36
9 BOMB CALORIMETER 37-43
10 JUNKER’S GAS CALORIMETER 44-49
11 CLOUD & POUR POINT TEST 50-54
12 PENETRATION TEST 55-58
13 ORSAT ANALYSER 59-64
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
turimeter
VENTURIMETER
AIM:
To determine coefficient of discharge for a given venturimeter
THEORY:
Venturimeter is a device invented by Ciemens Herchel in 1887 and named by
him after Venturi, who experimented with diverging tubes for the measurement of
rate of flow in pipe lines. The basic principle on which Venturimeter works is that by
reducing the cross-sectional area of the flow passage, a difference of pressure is
created and the measurement of the pressure difference enables the determination
of the discharge through the pipes. The fluid flowing the pipe is led through a
contracting section to a throat which has a smaller cross section area than the pipe,
so that the velocity is accomplished by a fall in 2mN . The magnitude of which
depends up on the rate of flow so that by measuring the pressure drop, the
discharge can be calculated. Beyond the throat the fluid is in a pipe of slowly
diverging section, the pressure increasing as velocity falls.
In a water distribution system and in processing industries it is necessary to
measure the volume of liquid flowing through a pipe line. The Venturimeter is
introduced in the pipeline to achieve this. Hence knowledge of the value of the
coefficient of discharge of the Venturimeter is a must. The velocity of flow through a
Venturimeter is obtained by applying Bernoulli’s theorem. The theoretical discharge
can be calculated by using the velocity obtained.
Q=2
2
2
1
21
aa
gh2aa
Where 1a = Cross sectional area of a pipe
2a = Cross sectional area at throat of venturimeter
h = Differential pressure head between entrance and Throat of
venturimeter
g = Gravitational acceleration
The actual discharge is determined by collecting water over a known period of time.
Coefficient of discharge for Venturimeter elDischTheoretica
ehActualDiscCd
arg
arg
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
turimeter
APPARATUS:
Venturimeter
Differential manometer
Collecting tank with piezometer
Scale
Stop watch
PROCEDURE:
Record the diameter of inlet 1d and throat 2d of the Venturimeter. As
certain that manometric fluid levels in the manometer limbs are the same.
Start the motor, Open the gate valve , allow the water to flow through pipe full
Reject the air bubbles if any by slowly raising the pinch cock
Note the manometric fluid levels h1 and h2 in the two limbs of the manometer
Measure the diameter of the collecting tank
Collect the water in collecting tank say 1 cm or 2 cm and note down the initial
reading.
Collect the water in the collecting tank up to the level more than 3/4 of the
collecting tank and note down the rise(R) of water level and corresponding
time (t)taken to rise that level
Repeat the above procedure by gradually increasing the flow and note down
the required readings.
The observations are tabulated and coefficient of discharge of venturimeter is
computed
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
turimeter
OBSERVATIONS AND RECORDING:
1. Diameter of venturimeter 1d ………………… cm
2. Diameter of venturimeter at throat 2d ………………… cm
3. Diameter of collecting tank D ………………….. cm
4. Specific gravity of manometric fluid S = ………………
CALCULATION:
1. Area of cross section at inlet 2
114
da
……………. 2cm
2. Area of cross section at throat 2
124
da
…………… 2cm
3. Area of collecting tank 2
4DA
………………………… 2cm
4. Rise of water level in the collecting tank R = …………. cm
5. Volume of water collected in Tank V = RA = …………. 3cm
6. Actual discharge t
VQa ……………………………….
sec
3cm
7. Theoretical Discharge 2
2
2
1
21 2
aa
ghaaQt
…………..
sec
3cm
8 Coefficient of discharge for Venturimeter t
a
dQ
QC
turimeter
TABULAR FORM
S.No.
Manometer reading
Rise of
water
level in
the
collecting
tank
R
cm
Time for
collecting
R cm rise
of water,
t sec.
Area of
collecting
tank
A
2cm
Volume of water
collected
RAVt 3cm
Actual Discharge
t
VQa
sec
3cm
Theoretical discharge
2
2
2
1
21 2
aa
ghaaQt
sec
3cm
Coefficient
of discharge
for
Venturimeter
t
a
dQ
QC
h1 cm
h2 cm
h =
121 Shh cm
of water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Venturimeter
MODEL GRAPHS:
A calibration curve between differential pressure head H on X-axis and
actual discharge aQ on Y-axis is drawn.
A graph for aQ on X-axis and h on Y-axis is plotted. The graph is a
straight line passing through the origin. aQ = hK
where K is a constant for a given meter.
dC = C
K where C =
2
1
2
1
21 2
aa
gaa
and from graph K =
h
Qa
dC is determined by a logarithmic plotting between H
10log on X-axis and
Q
10log a on Y-axis. It is a straight line intercepting the Y-axis. The intercept
above X-axis is K
10log and dC = C
K
aQ aQ
aQlog
PRECAUTIONS:
1. Conform that there are no air bubbles in the flow of water
2. Readings should be noted with out any parallax error
h
hlog
h
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Venturimeter
RESULT:
1. Coefficient of discharge theoretically = ………
2. Coefficient of discharge from aQlog Vs hlog =……
3. Coefficient of discharge from aQ Vs h =…..
VENTURI METER
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orificemeter 11
ORIFICEMETER
AIM:
To determine coefficient of discharge for a given orifice meter.
THEORY:
Orifice meter is used to measure the discharge in any closed surface.
Orifice meter works on the principle that by reducing the cross section area of the
flow passage, a pressure difference between the two sections is developed and
this difference enables the determination of the discharge through the pipe.
In a water distribution system and in processing industries it is necessary to
measure the volume of liquid flowing through a pipe line. The orifice meter is
introduced in the pipeline to achieve this. Hence knowledge of the value of the
coefficient of discharge of the orifice meter is a must. Orifice meter consists of a
flat circular plate with a circular hole called orifice, which is concentric with the
pipe axis pressure tapings are connected to pipe wall on the both sides of the
plate. So that the difference in the fluid pressure on both sides of the orifice plate
are measured. As the fluid passes through the orifice meter, a lot of eddies are
formed and there is a loss of energy due to which the actual discharge aQ , is far
less than thQ and is given by
2
2
2
1
2121 )(2
aa
hhgaaCQ
d
Th
Where dC is the coefficient of discharge
1a is the cross section area of pipe
2a is the cross section area of orifice
21 hhH = difference in piezometric readings of upstream and down stream of
orifice plate.
The actual discharge aQ is determine by collecting water over a know period of
time.
Coefficient of discharge for orifice meter dC = eDischlTheoretica
eDischActual
arg
arg
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orificemeter 12
APPARATUS:
Orifice meter setup
Differential manometer
Collecting tank with piezometers
scale
PROCEDURE:
Record the diameter of inlet 1d and throat 2d of the Venturimeter. As
certain that manometric fluid levels in the manometer limbs are the same.
Start the motor ,Open the gate valve , allow the water to flow through pipe
full
Reject the air bubbles if any by slowly raising the pinch cock
Open the inlet and outlet Nipples to allow water into the two limbs of the
manometer
Note the manometric fluid levels h1 and h2 in the two limbs of the
manometer
Measure the diameter of the collecting tank
Collect the water in collecting tank say 1 cm or 2cm and note down the
initial reading.
Collect the water in the collecting tank up to the level more than 3/4 of the
collecting tank and note down the rise(R) of water level and corresponding
time (t)taken to rise that level
Repeat the above procedure by gradually increasing the flow and note
down the required readings.
OBSERVATIONS AND RECORDING:
1. Diameter of pipe 1d ………………… cm
2. Diameter of orifice meter 2d ……………… .cm
3. Diameter of collecting tank D ………………….. cm
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orificemeter 13
CALCULATION:
1. Area of cross section of inlet 2
114
da
……………. 2cm
2. Area of cross section of orifice meter 2
124
da
…………… 2cm
3. Area of collecting tank 2
4DA
………………………… 2cm
4. Rise of water level in the collecting tank R = …………. cm
5. Volume of water collected in Tank V = RA = …………. 3cm
6. Actual discharge t
VQa ……………………………….
sec
3cm
7. Theoretical Discharge
2
2
2
1
21 2
aa
ghaaQt
…………..
sec
3cm
8. Coefficient of discharge for orifice meter t
a
dQ
QC
Orificemeter 14
TABULAR FORM
S.N
o
Manometer reading
Rise of
water
level in
the
collecting
tank
R
cm
Area of
collecting
tank
A
2cm
Volume
of water
collected
RAVt
3cm
Actual
Discharge
t
VQa
sec
3cm
Theoretical
discharge
2
2
2
1
21 2
aa
ghaaQt
sec
3cm
Coefficient of
discharge for
orificemeter
t
a
dQ
QC
1h
cm
2h
cm
h =
121 Shh
cm
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orificemeter 15
MODEL GRAPHS:
1. A graph between on aQ on Y-axis and H on X-axis is drawn. It is a
straight line passing through origin. dC = C
K where
2
2
2
1
21 2
aa
ghaaC
2. A graph is drawn between aQ and thQ and the value of dC is determined.
3. Draw a graph between aQ Vs h
4. Draw a graph between aQlog Vs hlog
aQ aQ
aQlog
h
hlog
h
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orificemeter 16
PRECAUTIONS:
1. Conform that there are no air bubbles in the flow of water
2. Readings should be noted without any parallax error
RESULT:
1. Coefficient of discharge theoretically = ………
2. Coefficient of discharge from aQlog Vs hlog =……
3. Coefficient of discharge from aQ Vs h =…..
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orifice Apparatus
18
ORIFICE
AIM : To determine coefficient of discharge, coefficient of velocity, &
coefficient of contraction of the small orifice.
THEORY:
Orifice is an opening having a closed perimeter made in the walls of a
tank containing fluid through which the fluid may be discharged. The
discharged fluid from the tank through the orifice comes out in the form of a
free jet in the process the total energy of the fluid in tank is converted to
kinetic energy as the jet issues out in the atmosphere.
The jet cross section initially contracts to a minima and then expands
partly due to the resistance offered by the surrounding atmosphere and partly
due to inertia of fluid particles. The section which has the minimum area is
known as “VENA CONTRACT”. The contraction and expansion of jet results
in loss of energy. The ratio between area of jet of vena contraction and the
area of orifice is known as coefficient of contraction cC . The value depends
upon the shape and size on the orifice on the head causing flow. Diameter of
jet at vena contract is measured by contracting gauge.
cC = a
c
a
a =
orificeofArea
VatjetofArea c
The actual velocity at vena contract is smaller then the theoretical
velocity due to frictional resistance at orifice edges. The ratio between actual
velocity and critical velocity of jet is known as coefficient of velocity for a
vertical orifice is determined experimentally by measuring the horizontal and
vertical coordinates of issuing jet. Water flows through an orifice under
constant head. Let v be the actual velocity. Consider a small particle of water
at vena contract, suppose it falls through a vertical distance „y‟ in horizontal
distance „x‟ in time„t‟.
x = vt, y = 2
1gt
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orifice Apparatus
19
y
gxV
2 thV = gh2
gHy
gxCv
22
2
=
yH
x
4
Since actual area of the jet is less than the area of orifice and actual
velocity is less than the theoretical velocity; therefore actual discharge is
lesser than the discharge and the discharge is called the coefficient of
discharge dC
gHQ
Q
Q
QC a
th
a
d2
Actual discharge aCgHCQ cva 2
gHa
gHaCCC
cv
d2
2
cvd CCC
Experimental procedure:-
1. After priming the pump, start the pump and slowly close the by pass
valve and water starts flowing into orifice tank.
2. Adjust the over flow pipe to get a constant head above the orifice with
minimum overflow.
3. Using contracting gauge find the diameter of the jet at vena contract
and hence the coefficient of contraction cC .
4. Adjust the points for measuring x and y coordinates at the jet knowing
the head causing H. vC is determined.
5. Collect certain quantity of fluid in the measuring tank foe unit time.
Hence actual discharge can be calculated.
6. Repeat the experiment for different heads over orifice for different
diameters of orifice.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orifice Apparatus
20
OBSERVATIONS:
Area of cross section of collecting tank = m2
Diameter of orifice d = cm
X correction = cm
Y correction = cm
Area of orifice, 2
4da
= 2m
CONSTANT HEAD METHOD:
S.No
Head
Hcm
Discharge
volume
Time sec
Discharge
sec
3m
th
a
Q
QC
d
1T 2T Avg aQ thQ
FALLING HEAD METHOD:
S.No
Initial
Reading
1H cm
Final Reading
2H cm
Time
sec 21 HH
T
KCd
MODEL GRAPHS
Draw a graph between aQ Vs H
Draw a graph between aQ Vs thQ graph
Draw a graph between aQ Vs H graph
Draw a graph between T Vs 1H - 2H
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Orifice Apparatus
21
aQ aQ
Results:
dC from falling head contraction =
dC from constant head observations =
dC from aQ Vs thQ graph =
dC from aQ Vs H graph =
dC from T Vs 1H - 2H =
aQ
T
1H -
2H
H thQ
H
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
External Mouth Piece 23
EXTERNAL MOUTH PIECE
AIM:
To determine the coefficient of discharge by falling head method.
DESCRIPTION:
Mouthpiece is a short tube attached to an orifice. By attaching a tube of
length 3-d to 5-d where d is the diameter of the mouthpiece, the discharge
through the mouthpiece increases by about 30% over small orifice for the same
head of liquid. The co-efficient of discharge is obtained the ratiot
a
.
For constant head method gHaQt 2
For falling head method g2Ta
)HH(A2C
21b
d
APPARATUS:
Mouthpiece fixed to a balancing tank,
Collecting tank
Stop watch,
PROCEDURE:
1. Fit the required mouth piece to the side of the tank, close the drain cock
2. Start the motor and allow the water in to the tank.
3. The balancing tank is filled with water completely by opening the inlet
valve fixed on the pipeline. After filling the balancing tank, the inlet valve is
closed completely
4. As the water flows through the mouthpiece, the head of water gradually
falls. After closing the inlet valve, the stopwatch is started when the water
level reaches a convenient level on the scale and stopped when the head
of water falls by 10cm . The water level in the balancing tank is read
through the piezometer tube on the scale. .
5. The balancing tank is again filled with water completely to the when the
head of water level attains the above initial scale reading, the stop watch is
started and time not for a fall of head by 20 cm
6. The procedure is repeated for other observations, increasing the fall head
by 10 cm for each observation. The initial head and terminal head are
recorded as H1 and H2 respectively.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
External Mouth Piece 24
7. The observations are tabulated and coefficient of discharge of external
mouth piece is computed
OBSERVATIONS:
Type of mouth piece : External mouth piece
Diameter of mouthpiece d =-------------------------- cm
Size of balancing tank b =-------------------------- cm
CALCULATIONS:
Area of balancing tank bA =-------------------------- 2cm
Area of mouth piece a =-------------------------- 2cm
Initial head over mouth piece 1H =-------------------------- cm
Final head over mouth piece 2H =-------------------------- cm
Coefficient of discharge g2Ta
)HH(A2C
21b
d
TABULAR FORM
S.No.
Head over Mouth Piece
Time taken for head to fall from
1H to
2H
T sec
1H
cm
2H
cm 1H -
2H
cm g2Ta
)HH(A2C
21b
d
Initial
1H cm
Final
2H
cm
GRAPHS:
A graph between T on x-axis and 21 HH on y - axis is drawn. The
value of the constant,
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
External Mouth Piece 25
g2a
A2K b is determined,
T
)HH(KC
21
d
Draw a graph between aQ Vs H
Draw a graph between aQ Vs thQ graph
Draw a graph between aQ Vs H graph
aQ aQ
aQ
T
1H -
2H
H thQ
H
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
External Mouth Piece 26
RESULTS:
Coefficient of discharge dC = ------------------
dC from aQ Vs H =
dC from aQ Vs thQ graph =
dC from aQ Vs H graph =
dC from T Vs 1H - 2H =
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Rectangular Notch 28
RECTANGULAR NOTCH
AIM:
To determine coefficient of discharge of Rectangular Notch
APPARATUS:
rectangular Notch setup
Differential manometer
Collecting tank with piezometer
Scale
Stop watch
THEORY:
A notch may be defined as an opening provided in the side of a tank such
that the fluid surface in the tank is below the top edge of the opening. The water
flowing through the notch is known as nappy. The bottom edge of a notch over
which the water flows is known as the sill and its height above the bottom of the
tank or channel is known as crest height. The notches are usually classified
according to the shape of openings. The edges of the notch are leveled on the
down stream side so as to have sharp edged sides and crest, resulting minimum
contract with the flowing liquid.
DESCRIPTION:
The equipment consists of supply tank supported on a strong iron stand.
Perforated sheets are fixed to the up stream side to serve as baffles when water
flows through baffles, the oscillations are damped out and a steady and smooth
flow is guaranteed.
The front side of the supply tank is provided with interchangeable notch
plates, which can be screwed to the tank front. An inclined Piezometre is fixed to
one side of the tank, which serves the purpose of finding the levels of water
surface.
A collecting tank is used to determine the actual discharge. Water is supplied to
the main channel from water through a gate valve, which is employed for
regulation of discharge. A drain cock is provided at the bottom side of the
channel.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Rectangular Notch 29
PROCEDURE:
Fit the required notch, Close the drain cock
Allow water in the channel
Regulate the gate valve so that water just flows over the sill.
Take reading in the inclined piezometer.
Allow more water and the discharge is maintained constant by regulating
the gate valve.
Take the reading in inclined piezometer.
Measure the diameter of the collecting tank
Collect the water in collecting tank say 1 cm or 2cm and note down the
initial reading.
Collect the water in the collecting tank up to the level more than 3/4 of the
collecting tank and note down the rise(R) of water level and corresponding
time (t)taken to rise that level
Repeat the above procedure for different heads.
The observations are tabulated and coefficient of discharge of rectangular
notch is computed
OBSERVATION
Diameter of the collecting tank D = ` cm
Width of the notch ( b ) = cm
Inclination of Piezometer =
CALCULATION:
Area of the collecting tank 2
4dA
………….. 2cm
Rise of water level R = ………….. cm
Volume of water collected RAVt …….. 3cm
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Rectangular Notch 30
Actual discharge t
VQ t
a ……………….sec
3cm
Net head sin21 hhh …………………..cm
Theoretical discharge aQ = 23
23
2hbg …………..
sec
3cm
Coefficient of discharge dC = t
a
Q
Q
Rectangular Notch 31
TABULAR FORM
S.No
Name of the notch
Piezometer reading
Net head
sin21 hhh
cm
Rise of water
level in the
collecting tank
R cm
Time taken to rise R
cm
t sec
Volume of water collected
tV =
A x R 3cm
Actual Discharge
aQ = t
AR
sec
3cm
Theoretical Discharge
aQ =
23
23
2hbg
sec
3cm
Coefficient of
discharge
dC =
t
a
Q
Q
Initial
1h
cm
Final
2hcm
1
2
3
4
5
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Rectangular Notch 32
MODEL GRAPHS:
A calibration curve between the head on the notch 23
H on x-axis and aQ
on Y-axis is drawn.
A straight line graph between aQ on X-axis and 23
H on Y-axis is drawn.
From the graph the values of 2
3
H
QK a is determined. dC =
CK , where
gLC 23
2
A graph between LogH10 on X-axis and
aQ
10log on Y-axis is drawn.
The intercept of the straight line on Y-axis measured from X-axis gives the
value of
k
10log
23
H
aQ
PRECAUTIONS:
1. Readings should be taken with out parallax error
2. Sill level reading should be taken exactly
Log k
Log aQ
Log 23
H
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Rectangular Notch 33
RESULT:
1. Average coefficient of discharge experimentally equal to ………………..
2. Coefficient of discharge from graph aQ Vs 2
5
h ……………………………..
3. Coefficient of discharge from graph log aQ Vs log 25
h ……………….
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Rectangular Notch 34
RECTANGULAR NOTCH
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
V Notch 36
V-NOTCH
AIM:
To determine the coefficient of discharge of a V- Notch
THEORY:
A notch may be defined as an opening provided in the side of a tank such
that the fluid surface in the tank is below the top edge of the opening. The water
flowing through the notch is known as nappy. The bottom edge of a notch over
which the water flows is known as the sill and its height above the bottom of the
tank or channel is known as crest height. The notches are usually classified
according to the shape of openings. The edge of the notch is leveled on the
down stream side so as to have sharp edged sides and crest, resulting minimum
contract with the flowing liquid.
DESCRIPTION:
The equipment consists of supply tank supported on a strong iron stand.
Perforated sheets are fixed to the up stream side to serve as baffles when water
flows through baffles, the oscillations are damped out and a steady and smooth
flow is guaranteed.
The front side of the supply tank is provided with interchangeable notch plates,
which can be screwed to the tank front. An inclined Piezometre is fixed to one
side of the tank, which serves the purpose of finding the levels of water surface.
A collecting tank is used to determine the actual discharge. Water is supplied to
the main channel from water through a gate valve, which is employed for
regulation of discharge. A drain cock is provided at the bottom side of the
channel.
APPARATUS:
Triangular Notch setup
Differential manometer
Collecting tank with piezometer
Scale
Stop watch
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
V Notch 37
PROCEDURE:
Fit the required notch, Close the drain cock
Allow water in the channel
Regulate the gate valve so that water just flows over the sill.
Take reading in the inclined piezometer.
Allow more water and the discharge is maintained constant by regulating
the gate valve.
Take the reading in inclined piezometer.
Measure the diameter of the collecting tank
Collect the water in collecting tank say 1 cm or 2cm and note down the
initial reading.
Collect the water in the collecting tank up to the level more than ¾th of the
collecting tank and note down the rise(R) of water level and corresponding
time (t)taken to rise that level
Repeat the above procedure for different heads.
The observations are tabulated and coefficient of discharge of rectangular
notch is computed
OBSERVATION
Diameter of the collecting tank D = cm
Angle of V- Notch =
Inclination of Piezometer =
CALCULATION:
Area of the collecting tank 2
4dA
………….. 2cm
Rise of water level R = ………….. cm
Volume of water collected RAVt …….. 3cm
Actual discharge t
VQ t
a ……………….sec
3cm
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
V Notch 38
Net head sin21 hhh …………………..cm
Theoretical discharge aQ = 25
h2
tang215
8
…………..
sec
3cm
Coefficient of discharge dC = t
a
Q
Q
39
TABULAR FORM
S.No
Name of the notch
Piezometer reading
Net head
sin21 hhh
cm
Rise of water
level in the
collecting tank
R cm
Time taken to rise R
cm
t sec
Volume of water collected
tV =
A x R 3cm
Actual Discharge
aQ = t
AR
sec
3cm
Theoretical Discharge
aQ =
25
h2
tang215
8
sec
3cm
Coefficient of
discharge
dC =
t
a
Q
Q
Initial
1h
cm
Final
2hcm
1
2
3
4
5
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
V Notch
40
MODEL GRAPHS:
A calibration curve between the head on the notch H on x-axis and aQ on
Y-axis is drawn.
A straight line graph between aQ on X-axis and H5/2 on Y-axis is drawn.
From the graph the values of 2
5
a
H
QK is determined. dC =
CK , where
2Tang2
15
8C
A graph between LogH10 on X-axis and
aQ
10log on Y-axis is drawn.
The intercept of the straight line on Y-axis measured from X-axis gives the
value of
k
10log
25
h
aQ
PRECAUTIONS:
1. Readings should be taken with out parallax error
2. Sill level reading should be taken exactly
RESULT:
1. Average coefficient of discharge experimentally equal to ………………..
2. Coefficient of discharge from graph aQ Vs 2
5
h ……………………………..
3. Coefficient of discharge from graph log aQ Vs log 25
h ………………
Log k
Log aQ
Log h5/2
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
V Notch
41
.
V NOTCH
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Verification of Bernoulli’s Theorem 43
VERIFICATION OF BERNOULLI’S THEOREM
AIM: Experimental Verification of Bernoulli’s theorem
DESCRIPTION:
The apparatus consists of a receiving cylinder to store water to the
required head, a closed conduit of uniformly varying cross - section, number of
piezometers take along the path of the conduit to measure the pressure head at
the point, and a controlling valve to control rate of flow of water. A collecting tank
is provided to find out the actual discharge. According to Bernoulli’s theorem, the
sum of pressure head, velocity head and elevation head is constant for all points
along a continuous conduit of frictionless flow.
CZg
V
W
P
2
2
APPARATUS:
1. Bernoulli’s equipment
2. Stop watch
3. Meter scale
PROCEDURE:
1. Open the gate valve and allow the water to flow through receiving cylinder
2. Slowly open outlet gate valve and adjust the supply such that for a particular
head in the receiving cylinder, the inflow and outflow are equal.
3. Note the height of water in receiving cylinder.
4. Note the height of water above the center of conduit in each tube.
5. Find out the rise of water level in the collecting tank for 10sec.
6. Calculate the area of cross–section of the conduit at points where the
pressure heads are measured.
7. Change the discharge and repeat the procedure.
OBSERVATION:
1. Area of cross –section of flow at different points, a1,a2…….a8 = 2cm
2. Diameter of the collecting tank (D) = ……………. cm
3. Elevation head, Z …………….cm
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Verification of Bernoulli’s Theorem 44
CALCULATIONS
1. Area of cross section of collecting tank, A = 2
4D
=… 2cm
2. Height of water in the receiving cylinder (R) = …………. cm
3. Volume of water collected in the tank RAVt =……… 3cm
4. Actual discharge t
VQ t
a …………
sec
3cm
5. Velocity of flow at a point a
Qv a ………………
seccm
6. Velocity head at point =g
V
2
2
……………… cm
7. Pressure head at the point W
P = …………….. cm
8. Total head at the point =
02
2
g
V
W
P…………….. cm
45
TABULAR FORM
S.No Height of
water level in the receiving cylinder cm
Piezometer tube No.
Pressure
head W
P
cm
Rise of water level in the collecting tank for 10 sec
R cm
Area of collecting tank
a 2cm
Volume of water collected
V 3cm
Area of flow A cm
2
Actual Discharge
t
VQ t
a
sec
3cm
Velocity
a
Qv a
seccm
Velocity head
g
V
2
2
cm
Total head
g
V
W
P
2
2
1
1 2 3 4 5 6 7 8
2
1 2 3 4 5 6 7 8
3
1 2 3 4 5 6 7 8
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Verification of Bernoulli’s Theorem
46
MODEL GRAPHS
Total Head No of tube
PRECAUTIONS:
1. Note down the readings with out parallax error
RESULT:
Bernoulli’s theorem is verified experimentally
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Verification of Bernoulli’s Theorem
47
BERNOULLI’S APPARATUS
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Losses in Pipes Due to Friction
LOSSES IN PIPES DUE TO FRICTION
AIM:
To determine the co-efficient of friction for a given pipe
THEORY:
The fluid flow through a pipe line is characterized by energy losses.
Energy loss is characterized as major energy loss and minor energy losses.
Major energy loss is due to the friction and minor energy loss is due to the
change in pipe line geometry. Energy loss due to friction is much more than the
minor losses so that minor losses can be neglected. While the nature of flow
depends upon the flow Reynolds’s number, the frictional resistance offered to the
flow of fluid depends essentially on the roughness of the surface of the conduct
carrying the flow. in laminar flow the frictional resistance is due to viscous
resistance of the fluid to flow. in turbulent it is due to the resistance offered by
viscosity of fluid and surface roughness of the conduct.
The frictional resistance varies with
With the degree of roughness of surface with which fluid comes in contact.
With the extent of area of surface coming in contact with the fluid
Directly as the velocity in laminar flows and as the square of velocity in
laminar flows and as the square of velocity in turbulent flow
Directly as the density of fluid
Inversely as the velocity of fluid
The friction loss for a pipe line is determined by Darcy – Weisbach equation
which is capable to both laminar and turbulent flow in a pipe line.
The loss of head due to friction is given by the Darcy’s Formula. gd
flvh f
2
4 2
The coefficient of friction 24
2
lv
gdhf
f
APPARATUS:
Pipe friction apparatus with pipes of different diameters fitted with inlet and outlet Nipples.
U-Tube manometer
collecting tank
Stopwatch
Metre scale
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Losses in Pipes Due to Friction
EXPERIMENTAL PROCEDURE
1. Connect the U-Tube manometer to the pressure tapings of the pipe for
which coefficient of friction is to be determined.
2. Start the motor ,Open the inlet valve to allow uniform flow through the pipe
3. Reject the air bubbles if any by slowly raising the pinch cock
4. Open the inlet and outlet Nipples to allow water into the two limbs of the
manometer.
5. Note the manometric fluid levels h1 and h2 in the two limbs of the
manometer
6. Measure the diameter of the collecting tank
7. Collect the water in the collecting tank up to the level more than 3/4 of the
collecting tank and note down the rise(R) of water level and corresponding
time (t)taken to rise that level
8. Repeat the above procedure by gradually increasing the flow and note
down the required readings.
OBSERVATION AND RECORDING
1. Diameter of the collecting tank D …..…. cm
2. Diameter of the pipe d …..……… cm
3. Length of the pipe l ……….. cm
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Losses in Pipes Due to Friction
CALCULATION:
1. Area of collecting tank A 4
2D ……. 2cm
2. Rise of water level in the collecting tank R =….. cm
3. Volume of water collected in the tank V = RA ………. 3cm
4. Discharge t
RXAQact )( …………
sec
3cm .
5. Area of the Pipe a4
2d …….. 2cm
6. Velocity of flow v = a
Qact ……….sec
cm .
7. Coefficient of friction 24
2
lv
gdhf
f
Losses in Pipes Due to Friction
TABULAR FORM
S. No
Manometer reading
1 shh f
cm of
water
Rise of water level
in the collecting
tank
R cm
Time for collecting R cm rise of
water, t sec.
Area of collecting
tank
A 2cm
Volume of water
collected V =
RA 3cm
Actual Discharge
tVQa
sec
3cm
Velocity
v = a
Qa
seccm
24
2
lv
gdhf
f
1h
cm
2h
cm
21 hhh
cm
1
2
3
4
5
Avg f =
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Losses in Pipes Due to Friction
MODEL GRAPHS:
1. Draw a graph between fh Vs 2V
2. Draw a graph between log fh Vs log 2V
PRECAUTIONS:
1. Readings should be taken with out parallax error
2. Remove the air bubbles from the manometer tubes
RESULT:
1. Average coefficient of friction experimentally ……………
2. Coefficient of friction from graph fh Vs 2V
………………….
3. Coefficient of friction from graph log fh Vs log 2V ………………
2V
fh
log fh
klog
log 2V
2V
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Losses in Pipes Due to Friction
LOSSES IN PIPE
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Minor Losses in a Pipe 56
MINOR LOSSES IN A PIPE
AIM:
To determine form (minor) losses in pipe.
INTRODUCTION:
In most of the pipe flow problems, the flow is steady and uniform, and the loss
of head due to friction is predominant. In edition to the loss of head due to friction,
the loss of head is also occurs whenever there is change in the diameter or
direction, or there is any obstruction in the flow. These losses are called form losses
or minor losses.
The form losses are usually small and insignificant in long pipes but for pipes
of small length, they are quit large compared to the friction loss. In some small
length pipes, they mat be even more predominant than that due to friction.
EXPERIMENTAL SETUP:
The set-up consists of a small diameter pipe which suddenly changes to a
large diameter pipe. After a certain a length, the large diameter reduces to a small
diameter. The small diameter pipe has a 900 bend. Suitable pressure tapping points
are provided to measure the loss of head with an inverted U-tube manometer. The
loss of head can be determined by connecting the manometer across the section
where the changes occur in the flow.
The pipe is connected to a constant-head supply tank. The water is collected
in measuring tank for the determination of the discharge.
THOERY:
The form losses are usually expressed as
g
VKH L
2
2
Where,
V is the mean velocity of flow,
K is the form loss factor, which depends upon the type of obstruction or
change, the type of flow and the velocity, etc.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Minor Losses in a Pipe 57
The loss of head due to sudden expansion is usually determined by the Borda-
carnot equation,
g
VVH L
2
2
21
Where
V1 is the velocity in the smaller pipe and
V2 is the velocity in the larger pipe,
Eq (a) can be expressed as
g
VKH eL
2
2
1
Where,
eK is the coefficient for sudden expansion. The value of eK depends upon
2
1
d
dratio. For gradual expansion (diffusers), the value of eK depends upon
the2
1
d
dratio and the angle of divergence.
The loss of head due to sudden contraction is usually expressed as
g
VKH cL
2
2
1
Where
1V is the velocity in small pipe.
The value of cK is usually about 0.3 to 0.5.
For gradual contractions, the loss of head is considerly small.
The loss of head at a bend can be expressed as
g
VKH bL
2
2
The value of Kb depends upon the angle of bend, the ratio of the radius of
curvature of the bend to the diameter of the pipe (i. e. Dr ratio), and the roughness
of the pipe.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Minor Losses in a Pipe 58
For a 900 bend, the value of bK usually varies between 0.60 and 0.90.
PROCEDURE:
1. Measure the diameter of pipes. Also measure the dimensions of the collecting
tank.
2. Open the inlet valve.
3. Connect the manometer across the sections for which the loss of head due to
sudden expansion is to be measured.
4. Gradually adjust the exit valve. When the flow becomes steady, measure the
manometric deflection (h).
5. Take the initial reading of the measuring tank and start the stop watch. Note
the rise in water level for a suitable time period.
6. Repeat steps 4 and 5 for different discharges.
7. Repeat steps 3 to 6 for the loss of head due to sudden contraction.
8. Repeat steps 3 to 6 for the loss of head due to bend.
OBSERVATIONS AND CALCULATIONS:
Diameter of the smaller pipe, 1D =
Diameter of the larger pipe, 2D =
Dimensions of the measuring tank:
L = B = A =
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Minor Losses in a Pipe 59
SUDDEN EXPANSION
S. No.
Discharge Measurement Loss of head
V1 g2
V 2
1 V2 g2
V 2
2 eK Initial Level
Final Level
Rise in
Level Volume Time Q
Deflection (h)
h)S
s1(hf
1
1
1
2
3
4
SUDDEN CONTRACTION
S. No.
Discharge Measurement Loss of head
V1 g2
V 2
1 V2 g2
V 2
2 Kc Initial Level
Final Level
Rise in
Level Volume Time Q
Deflection (h)
h)S
s1(hf
1
1
1
2
3
4
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Minor Losses in a Pipe 60
PRECAUTIONS:
1. There should be no air bubble in the inverted U-tube and its Tapings.
2. Readings should be taken when the flow is steady.
3. Collect adequate quantity of water for the determination of discharge.
RESULT:
Average values of factor K for
a) Sudden expansion, eK =
b) Sudden contraction cK =
c) 900 bend, bK =
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Minor Losses in a Pipe 61
MINOR LOSSES IN PIPE
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Pelton Wheel
PELTON WHEEL
AIM:
Determination of efficiency of Pelton wheel at constant head.
APPARATUS: Pelton wheel test rigs, tachometer and weights.
DESCRIPTION:
Pelton wheel is an impulse turbine which is used to utilize high heads for
generation of electricity. It consists of a runner mounted on a shaft. To this a
brake drum is attached to apply brakes over the speed of the turbine. A casing is
fixed over the runner. All the available head is converted into velocity energy by
means of spear and nozzle arrangement. The spear can be positioned in 8
places that is, 1/8, 2/8, 3/8, 4/8, 5/8 6/8, 7/8 and 8/8 of nozzle opening. The jet of
water then strikes the buckets of the Pelton wheel runner. The buckets are in
shape of double cups joined at middle portion. The jet strikes the knife edge of
the buckets with least resistance and shock. The jet is deflected through more
than 160o to 170o. While the specific speed of Pelton wheel changes from 10 to
100 passing along the buckets, the velocity of water is reduced and hence the
impulsive force is supplied to the cups which in turn are moved and hence the
shaft is rotated. The supply of water is arranged by means of centrifugal pump.
The speed of turbine is measured with tachometer.
PROCEDURE:
1. Keep the nozzle opening at about 3/8th open position
2. Prime the pump if necessary
3. Close the deliver gate valve completely and start the pump.
4. Allow water in the turbine, and then the turbine rotates.
5. Adjust the deliver gate valve opening and note the Turbine inlet pressure.
6. Note the venturimeter pressure gauge readings.
7. Load the turbine by putting weights.
8. Note the speed of the turbine.
9. Note weight on hanger, W1 and spring balance weight W2 and weight of
hanger W0
10. Repeat the experiment for different loadings.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Pelton Wheel
OBSERVATIONS:
Venturimeter inlet Diameter, d1= 0.065 m
Venturimeter inlet area, a1 = 2
14
d
Venturimeter throat diameter ,d2= 0.039m
Venturimeter throat area, a2 = 2
24
d
Speed (N) = rpm
Diameter of brake drum , D = 0.4 m
Diameter of rope = 0.015 m
CALCULATION:
Inlet Pressure, P = Kg/cm2
Total Head, H = P10 m of Water
Venturimeter inlet pressure, P1 = Kg/cm2
Venturimeter throat pressure, P2 = Kg/cm2
Venturi Head , dH = 10 )( 12 pp m of water
Discharge Qact = Cd.2
2
2
1
21 2
aa
gdHaa
=
sec
3m
= 0.0055 x dH0.5
Cd = 0.98
1 Output Power [O.P] = 100060
NT2
…… KW
Where, N = Rated speed ….. Rpm,
W0 = Weight of hanger = 1.0 kg
W1 = Weight on hanger ………. kg
W2 = spring balance reading ……….kg
Re = Effective brake drum radius = (R + r) … m
Where R is Brake drum radius
r is Rope radius
F = Net Load = [(W1-W2) + W0] 9.81 ……… N
T = (F * Re)…………N-m
Input Power, I.P = 1000
HQW a …………… KW
Where W = Specific weight of water =9810 N/m3
Efficiency of Turbine, = 100.
.
PI
PO
Pelton Wheel
TABULAR FORM
S. No.
Inlet pressure
P kg/cm
2
Head
H m of water
Venturimeter Reading Discharge
actQ
sec
3m
Speed
N , rpm
Weight on hanger
W1
Kg
Spring balance
W2
Kg
Net weight
F, N
O.P KW
I.P KW
100.
.
PI
PO P1
kg/cm2
P2 kg/cm
2
dH m of water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Pelton Wheel
GRAPHS:
1. Unit Speed Vs
2. Unit Speed Vs Unit Output power
3. Unit Speed Vs Unit Discharge
RESULT
The efficiency of Pelton wheel Turbine at constant head =____
Nu
Nu
Nu
Unit D
isch
arg
e Q
u
Unit P
ow
er
Pu
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Pelton Wheel
PELTON WHEEL TURBINE PELTON WHEEL TURBINE
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Reciprocating Pump
RECIPROCATING PUMP AIM:
To determine the efficiency of a reciprocating pump and plot the operating
characteristics of the Pump
DESCRIPTION:
Single acting reciprocating pump which consists of a piston which moves
forwards and backwards in a close fitting cylinder. The movement of piston is
obtained by connecting rod. The crank is rotated by means of electric motor suction
and delivery pipes with suction valve are connected to the cylinder the suction and
delivery valves are one way or non return valves. Which allow the water to flow in
one direction by rotating the crank in the position θ= 0o to 1800 and 1800 – 3600 we
get the valves.
Discharge (Q) =60
ALN
Weight of water per sec = Qg
Work done =
100060
ds hhALNg ………kw
PROCEDURE:
1. Switch on the pump and open the discharge valve of the pump fully
2. After steady state is attained note down the suction pressure and delivery pressure
3. Note down time taken for 20revolutions in the energy meter
4. Measure the diameter of the collecting tank
5. Collect the water in collecting tank say 1 cm or 2 cm and note down the initial
reading.
6. Collect the water in the collecting tank up to the level more than ¾th collecting tank and note down the rise(R) of water level and corresponding time
t taken to rise that level
7. Operate the delivery valve and change the flow rate
8. Repeat the procedure for different flow rate by regulating discharge valve from maximum to minimum
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Reciprocating Pump
OBSERVATIONS
Diameter of collecting tank (D) =……………………… m
Energy meter constant , K = ---------------------
CALCULATION:
Suction head ( sh ) = 1000
w
sm
S
PS …………… m of water
Sm = Specific Gravity of mercury = 13.6
Sw = Specific Gravity of Water = 1
Discharge head ( dh )= Pd x10……………………… m of water
Total head hT = ds hh = …………………… . m of water
Area of collecting tank A = 2
4D
……………………… 2m
Rise of water level in the collecting tank (R) = ………… m
Volume of water collected in Tank V = RA = ………… 3m
Time taken for collecting R m rise of water (t)=………… sec
Actual discharge aQ = t
V…………………………………
sec
3m
Output power (O.P) =
1000
hTQW ………. kw
Number of Revolutions of energy meter n =
Time taken for ‘n’ number of revolutions of the energy meter mt = ……. sec
Indicated power IP = mtk
n
3600 … kw
Efficiency of pump , 100.
.
PI
PO
TABULAR FORM
S. No.
Suction pressure
Discharge pressure
Total head
hT =
ds hh
m of water
Rise of water
level in collecting tank
R
m
Time for collecting R m rise of water,
t sec.
Volume of water
collected
V =
RA 3m
Discharge
aQ =
t
Vsec
3m
Time taken for
20 rev of energy meter
mt sec
I.P
mtk
n
3600
kw
O. P
1000
ha TQW
kw
100.
.
PI
PO
sp
mm of
Hg
sh
m of
water
dp
2cmkg
dh
m of
water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Reciprocating Pump
MODEL GRAPHS
1. Draw a graph between hT Vs aQ
2. Draw a graph between PO. Vs hT
3. Draw a graph between η Vs hT
hT hT
hT
hT
aQ OP
η
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Reciprocating Pump
PRECAUTIONS :
Reading should be taken without any parallax error
The suction and delivery valves are completely opened before experiment
started
RESULT
The average efficiency of Reciprocating pump=……………
RESIPROCATING PUMP RECIPROCATING PUMP
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single Stage Cenrifugal Pump
SINGLE STAGE CENTRIFUGAL PUMP
AIM:
To determine the efficiency of a single stage centrifugal pump and plot the
operating characteristic curves.
THEORY:
In general a pump may be defined as a mechanical device which, when interposed
in a pipe line, converts the mechanical energy supplied to it from some external source
into hydraulic energy, thus resulting in the flow of liquid from lower potential to higher
potential.
The centrifugal pump which is of present concern falls into the category of
Rotodynamic pumps. In this pump, the liquid is made to rotate in a closed chamber
(volute casing) thus creating a centrifugal action which gradually built up the pressure
gradient towards outlet, thus resulting in the continuous flow. These pumps compared to
reciprocating pumps are simple in construction, more suitable for handling viscous, turbid
(muddy) liquids, can be directly coupled to high speed electric motors (without any speed
reduction ) & easy to maintain. But, their hydraulic heads at low flow rates is limited, and
hence not suitable for very high heads compared to reciprocating pump of same capacity.
But, still in most cases, this is the only type of pump which is being widely used for
agricultural applications because of its practical suitability.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single Stage Cenrifugal Pump
DESCRIPTION :
The present Pump Test Rig is a self-contained unit operated on
Closed circuit (Re circulation) basis. The Centrifugal pump, AC Motor, Sump tank,
Collecting tank, and Control panel are mounted on rigid frame work with Anti-vibration
mounts and arranged with the following provisions:
For conducting the experiments at three speeds using AC Motor.
To measure overall input power to the AC motor using Power meter.
For recording the Pressure & Vacuum.
For recording the speed using Digital RPM Indicator.
For changing the Pressure (Delivery Head) and Vacuum (Suction Head) by operating the valves.
For measuring the discharge by Collecting Tank – Piezo meter provision.
For recirculation of water back to the sump tank by overflow provision.
SPECIFICATIONS:
Electrical Supply : 230V, 15A, AC, 1 Phase, 50 Hz
Motor : AC Motor, 2 HP, 1500 RPM.
Centrifugal Pump : 2 HP, 3000 RPM (Max.) - Kirloskar Make.
Pressure Gauges : 2 2cmkg
Vacuum Gauge : 0 - 760 mm of Hg
Energy Meter : To measure input power.
Speed Indicator : 0 - 9999 RPM (Digital Type). Control Valves : For Suction & Delivery.
Measuring Tank Size : 0.242 2m
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single Stage Cenrifugal Pump
APPARATUS
Centrifugal pump
Collecting tank with piezometer
Pressure gauge
Suction gauge
Stop watch
Energy meter
Meter scale
PROCEDURE
1. Fill in the Sump Tank with clean water.
2. Keep the delivery valve closed and suction valve open, after initially priming the
pump.
3. Switch-ON the Mains, so that the Mains-ON Indicator glows. Now, Switch-ON the
Starter.
4. Open the delivery valve slightly, so that the delivery pressure is readable.
5. Operate the Butterfly Valve to note down the collecting tank reading against the
known time and keep it open when the readings are not taken.
6. Note down the Discharge Pressure, Suction pressure gauge readings
7. Note down Time for ‘n’ number of revolutions of Energy meter.
8. Repeat the experiment for different openings of the Delivery Valve.
9. After the experiment is over, keep the delivery valve in closed position.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single Stage Cenrifugal Pump
OBSERVATIONS
Energy Meter Constant ,K = 750 KWH
vRe
Area of Collecting Tank, A = 0.242 2m
CALCULATION:
Input Power (I.P)
tK
nPelect
3600 = KW
75.0 electshaft PP = KW
Where, Transmission Efficiency is taken as 75%.
Discharge Rate
t
RAQact
=
sec
3m
Where, A = 0.242 2m is the area of Collecting Tank,
R = the height of water collected in m
t = the time taken in seconds for collecting R m rise of water.
Suction head ( sh ) = 1000
w
sm
S
pS …………… m of water
Sm = Specific Gravity of mercury = 13.6
Sw = Specific Gravity of Water = 1
Discharge head ( dh )= pd x10……………… m of water
Total head hT = ds hh = ……………… m of water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single Stage Cenrifugal Pump
Output Power (Delivered by the Pump)
1000
hapump
TQWP
= kw
Where, Specific weight of water, W = 9810 3mN
Q act Actual Discharge .
Th,, Total Head
Pump Efficiency
100.
.
shaft
pump
pumpPI
PO
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single Stage Cenrifugal Pump
TABULAR FORM
S. No.
Suction pressure
Discharge pressure Total
head
hT =
ds hh
m of
water
Rise of water
level in collecting tank
R
m
Time for
collecting R
m rise of
water, t sec.
Volume of water collected
V =
RA 3m
Discharg
e
aQ
=
t
V
sec
3m
Time taken for 20 rev of
energy
meter
mt
sec
I.P
mtk
n
3600
kw
O.Pelec
1000
HQWPpump
kw
O.Pshaf=
O.Pelec
x 0.75
kw
100.
.
shaft
pump
pumpPI
PO
sp
mm o
f Hg
sh
m
of water
dp
2cmkg
dh
m of water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single stage Centrifugal Pump
MODEL GRAPHS
1. Discharge Vs Total Head
2. Discharge Vs Pump output
3. Discharge Vs Pump efficiency
aQ aQ
aQ
hT
pump
B.P
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single stage Centrifugal Pump
PRECAUTIONS:
Reading should be taken without any parallax error
The delivery valves id completely closed before experiment started
RESULT
The average efficiency of Centrifugal pump=……………
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Single stage Centrifugal Pump
SINGLE STAGE CENTRIFUGAL PUMP
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Cenrifugal Pump
-
MULTI STAGE CENTRIFUGAL PUMP AIM: To determine the efficiency of a multi stage centrifugal pump and plot the
operating characteristic curves.
THEORY:
A pump may be defined as a mechanical device which mean interposed in a
pipe line, converts mechanical energy supplied to it from some external source into
hydraulic energy, thus resulting in the flow of liquid from lower potential to higher
potential.
A centrifugal pump consists of an impeller in a volute casing. The impeller has
number of vanes (curved) to the eye of the pump a suction pipe is connected. At the
other end of this pipe a foot valve with a strainer is connected. The water enters at
the centre and flows out ward to the periphery of the impeller. In the delivery side of
a pipe a delivery pipe with a valve is fixed. The energy supplied to the motor is
measured by means of an energy meter. Suction and delivery pressure gauges are
fitted to suction and delivery pipes respectively near the pump.
A centrifugal pump may be driven with a constant speed or a variable speed motor.
The flow rate can be adjusted by operating the valve provided on the delivery pipe
line. The pressure drops a cross the pump is measured by the pressure gauges.
These centrifugal pumps are coming under rotodynamic pumps type and these
centrifugal pumps are used for more discharge and its working on the principle of
forced vortex. The main parts are impeller, casing suction pipe with strainer delivery
pipe, foot step valve with strainer.
In the case of centrifugal pump, work is done by the impeller on the water. The
expression for the work done by the impeller on the water is obtained by drawing
velocity triangles at inlet and outlet of the impeller on the same way as for a turbine.
The water enters the impeller radially at inlet for best efficiency of the pump. Which
means the absolute velocity of water at inlet makes an angle of 900 with the direction
of motion of impeller at inlet and work done by the impeller
2211
1uvwuvw
g
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Cenrifugal Pump
APPARATUS
Centrifugal pump
Collecting tank with piezometer
Pressure gauge
Suction gauge
Stop watch
Energy meter
Meter scale
PROCEDURE
1. Keep the delivery valve in closed and suction valve open position
2. Start the motor
3. Close the delivery valve slightly, so that the delivery pressure is readable.
4. Read the delivery pressure and suction pressure
5. Note down the time taken to 5 revolutions of energy meter
6. Measure the diameter of the collecting tank
7. Collect the water in collecting tank say 1cm or 2cm and note down the initial
reading.
8. Collect the water in the collecting tank up to the level more than ¾th of the
collecting tank and note down the rise(R) of water level and corresponding time
(t)taken to rise that level
9. Operate the delivery valve and change the flow rate
10. Repeat the experiment for different openings of the delivery valve
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Cenrifugal Pump
SPECIFICATIONS
Electric service : 180-250V AC, 3-Phase, 50Hz with earth connections
Motor : 1Hp, 1440Rpm
Centrifugal pump : 1hp, 2-stage- Suguna motor
Belt size A40
Pressure gauge : 22cm
kg
Suction gauge : 0 - 760 mm of gh
Watt meter : BHEL made
Control valves : for suction and delivery
Measuring tank : mmmm 300300
OBSERVATIONS
Diameter of collecting tank D =……………………… m
Energy meter constant = ---------------------
CALCULATION:
Suction head ( sh ) = 1000
w
sm
S
pS …………… m of water
Sm = Specific Gravity of mercury = 13.6
Sw = Specific Gravity of Water = 1
Discharge head ( dh )= pd x10……………… m of water
Total head hT = ds hh 2 = ……………… m of water
Area of collecting tank A = 2
4D
………… 2m
Raise of water level in the collecting tank R = ………… m
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Cenrifugal Pump
Volume of water collected in Tank V = RA = ………… 3m
Time taken for collection of ‘R’ m rise of water(t)=…………sec
Actual discharge aQ = t
V…………………………………
sec
3m
Output power OP = (1000
ha TQw )…………. kw
Number of Revolutions n = 5
Time taken for 5 revolution of the meter scale mt = …….sec
Input power IP = mtk
n
3600 … kw
Efficiency of pump , 100.
.
PI
PO
TABULAR FORM
S. No.
Suction pressure
Discharge pressure Total head
hT =
2 ds hh
m of water
Rise of water
level in collecting tank
R
m
Time for collecting R m rise of water,
t sec.
Volume of water
collected
V =
RA 3m
Discharge
aQ =
t
Vsec
3m
Time taken for
‘n’ rev of energy
meter scale
mt sec
I/P power
mtk
n
3600
kw
Output Power
1000
ha TQW
kw
100.
.
PI
PO
sp
mm of
Hg
sh
m of
water
dp
2cmkg
dh
m of
water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Centrifugal Pump
MODEL GRAPHS
1. Draw a graph between hT Vs aQ
2. Draw a graph between BHP Vs aQ
3. Draw a graph between η Vs aQ
aQ aQ
aQ
hT
pump
B.P
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Centrifugal Pump
PRECAUTIONS :
Reading should be taken without any parallax error
The delivery valve is completely opened closed before experiment is started
RESULT
The average efficiency of multistage Centrifugal pump=……………
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Multi Stage Centrifugal Pump
MULTI STAGE CENTRIFUGAL PUMP
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Francis Turbine
FRANCIS TURBINE
AIM:
Determine the efficiency of Francis Turbine at constant head
APPARATUS:
Francis turbine test rig, tachometer and weights.
DESCRIPTION:
Francis turbine consists of runner mounted on a shaft and enclosed in a spiral
casing with guide vanes. The cross section of flow between the guide vanes can be
varied, known as gate opening. It can be adjusted ¼, ½, ¾, or full gate opening. A
brake drum is fixed to the turbine shaft. By means of this drum the speed of the
turbine can be varied. The discharge can be varied by operating a throttle valve on
the pipe line. The water after doing work leaves the turbine through a draft tube and
flows down into the tail race. A Venturimeter is fitted to the pipe for measuring
discharge.
PROCEDURE:
1. Keep the guide vane at required opening (say 3/8th )
2. Prime the pump if necessary.
3. Close the main gate valve and start the pump.
4. Open the gate valve for required discharge
5. Open the brake drum cooling water gate valve for cooling the brake drum.
6. Note the Venturimeter pressure gauge readings
7. Note the inlet pressure gauge & outlet vacuum gauge readings
8. Note weight on hanger, W1 and spring balance weight W2 and weight of
hanger W0.
9. Measure the turbine runner speed in rpm with tachometer.
10. Repeat the experiment for different loadings.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Francis Turbine
OBSERVATIONS:
Venturimeter inlet Diameter, d1= 0.1 m
Venturimeter inlet area, a1 = 2
14
d
Venturimeter throat diameter ,d2= 0.06 m
Venturimeter throat area, a2 = 2
24
d
Speed (N) = rpm
diameter of brake drum , D = 0.3 m
Diameter of rope = 0.015 m
CALCULATION:
Inlet Pressure, P = Kg/cm2
Outlet Vacuum, V = mm of Hg
Total Head, H =
76010
VP m of Water
Venturimeter inlet pressure, P1 = Kg/cm2
Venturimeter throat pressure, P2 = Kg/cm2
Venturi Head , dH = 10 )( 12 pp meters of water
Discharge Qact = Cd.2
2
2
1
21 2
aa
gdHaa
=
sec
3m
= 0.0131 x dH0.5
Cd =0.98
1 Output Power [O.P] = 100060
NT2
…… KW
Where,
N = Rated speed ….. Rpm,
W0 = Weight of hanger = 1.0 kg
W1 = Weight on hanger ………. kg
W2 = spring balance reading ……….kg
Re = Effective brake drum radius = (R + r) … m
Where R is Brake drum radius
r is Rope radius
F = Net Load = [(W1-W2) + W0] 9.81 ……… N
T = (F * Re)…………N-m
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Francis Turbine
Input Power, IP = 1000
HQW a …………… KW
Where
W = Specific weight of water =9810 N/m3
Efficiency of Turbine 100.
.
PI
PO
Francis Turbine
S. No.
Inlet pressure
P kg/cm
2
Outlet Vacuu
m V
mm of Hg
Total Head,
H meter
of water
Venturimeter Reading Discharge
Q act
sec
3m
Speed
N , rpm
Weight on hanger
W1
Kg
Spring balance
W2
Kg
Net weight ,F
N
O.P Kw
I.P Kw
100.
.
PI
PO
P1
kg/cm2
P2 kg/cm
2
dH m of water
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Francis Turbine
GRAPHS:
1. Unit Speed Vs
2. Unit Speed Vs Output power
3. Unit Speed Vs Unit Discharge
RESULT
The efficiency of Francis Turbine at constant head =____
Nu
Nu
Nu
Unit D
isch
arg
e Q
u
Unit P
ow
er
Pu
Francis Turbine
FRANCIS TURBINE
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Study of Impact of Jet on Vanes
STUDY OF IMPACT OF JET ON VANES
AIM:
To conduct an experiment on the Jet on vane apparatus and determine the
efficiency of jet
THEORY:
The study of impact of a jet of water is essential to understand the principle of
an impulse turbine such as Pelton Wheel Turbine. When high pressure water from a
source such as a dam flows through a nozzle in the form of a jet, the entire pressure
energy of the water is converted into kinetic energy at the nozzle. When this jet of
water hits a vane positioned in front of it, the vane deflects the jet and due to the
change in the momentum of the water jet, a force is imparted to the vane by the
water.
EXPERIMENTAL SETUP:
The equipment consists of a high efficiency gun metal nozzle fitted to a 25
mm diameter pipe supply line with a gate valve. Vertically above the nozzle, a gun
metal vane is fitted to a bracket of a differential lever which balances the upward
force of the jet from the nozzle. The lever is provided with an adjustable no load
screw mechanism. The force due to the jet on the lever is counter balanced by
weights placed on a hanger. Different types of vanes can be fitted to the bracket.
The complete assembly is enclosed in a framed structure housing with two
leak proof transparent sides for visual observation. The water deflected by the vane
is collected in the collecting tank of the hydraulic bench.
For experimental purposes, two brass nozzles with nozzle outlet diameters of 8mm
and 10mm and two gunmetal vanes of the following shape are provided.
1. Semi-circular vane (1800 Angle of deflection)
2. Horizontal flat vane (900.angle of deflection)
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Study of Impact of Jet on Vanes
EXPERIMENTAL PROCEDURE:
1. Fit the required vane on the lever.
2. Measure the differential lever arms and calculate the ratio of lever arms (2.0 in
this case)
3. Balance the lever systems by means of counter weight for no load.
4. Place a weight on the hanger.
5. Open the gate valve and adjust the jet, so that the lever arm is balanced.
6. Collect water in the collecting tank.
7. Note (a) the pressure gauge reading – P.
(b) The weight placed – W.
(c) Time for 5 cm. rise in the collecting tank –t
8. Repeat the procedure for different loads
CALCULATIONS:
Area of collecting tank A = 5.05.0 msq.
Rise in water level R =
Time taken t = ------- sec
Actual flow rate aQ = t
AR
sec
3m
Actual mass flow rate m = Q sec
kg
where, = Mass density of water = 1000kg/m3
Nozzle diameter d = ---------------- m
Nozzle area a = 4
d 2
msq. .
Jet velocity (v) = a
Qa sec
m
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Study of Impact of Jet on Vanes
Theoretical lifting force = Change in momentum per sec. In vertical direction
thF = 21 SinSinvm
For Horizontal flat vane, 1 = 900 and 2 = 00
thF = vm …….N
For semi circular vane 1 = 900 and 2 = - 900.
thF = vm2 ……N
Actual lifting force = W lever arm ratio
actF = 2.0 W
Where, W is the weight placed on hanger ………N
Jet efficiency = th
act
F
F
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Study of Impact of Jet on Vanes
S.No. Pressure Rise water
level
collected
in
collecting
tank, R m
Time for
collecting
R m. Rise
of water, t
sec.
Volume of
water
collected, V
m3
Actual
Discharge,
t
VQa
Secm /3
Velocity
a
Qv a
Secm /
Mass
flow rate,
m =
aQ
Kg/Sec.
Weight
on
hanger,
W, N
100th
act
F
F Pressure
P Kg/cm2
Head
H1, m
of
water
RESULT:
The efficiency of the Jet is = _____________________
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Study of Impact of Jet on Vanes
IMPACT OF JET ON VANES
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Turbine Flow Meter 1
TURBINE FLOWMETER
AIM : To the calibrate the given Turbine flow meter .
THEORY:
The modern axial turbine flowmeter, when properly installed and
calibrated, is a reliable device capable of providing the highest accuracies
attainable by any currently available flow sensor for both liquid and gas
volumetric flow measurement. It is the product of decades of intensive innovation
and refinements to the original axial vaned flow meter principle.There are two
approaches described in the current literature for analyzing axial turbine
performance. The first approach describes the fluid driving torque in terms of
momentum exchange, while the second describes it in terms of aerodynamic lift
via airfoil theory. The former approach has the advantage that it readily produces
analytical results describing basic operation, In a hypothetical situation, where
there are no forces acting to slow down the rotor, it will rotate at a speed which
exactly maintains the fluid flow velocity vector at the blade surfaces.
PROCEDURE:
1. Fill the sump tank with water.
2. Switch on the power switch, “Mains On” starts glowing as well as digital
flow indicator.
3. Start the pump using supply pump starter, Regulate the valve and set the
water flow near to the maximum flow using Rotameter.( Almost 25 LPM)
4. Note down the time taken each 20 cm rise in water level in the
Piezometer for the above setting .
5. Observe the digital flow indicator, note down the reading in pulse per
second shown at the upper indication.
6. Now using the equation given calculate the factor and enter it in the
indicator using button “SET”. Once set button is pressed, using upper
arrow and downward arrow button factor can be fed to the indicator. Now
press “ENT” button to get the discharge in LPM through the Turbine meter.
7. To get different set of readings ,using valve set different flow rate at Rota
meter
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Turbine Flow Meter 2
(e.g.: 5, 10 etc.) and also Note down the time taken each 20 cm rise
in water level in the Piezometer
8. Calculate the actual discharge from the equation. Plot the graphs given.
Repeat the experiment for different discharge.
OBSERVATIONS:
Area of collecting tank A = 0.085 2m
TABULAR FORM
CALCULATIONS:
Pulse/sec =
Calculation for the “Factor”:
Factor = spulseInRotationMeterFlowTurbine
Qrotameter
/
Rise of water level in collecting tank R = cm
Time for 'R' cm rise of water in collecting tank t = sec
Actual Discharge calQ
S. No
Rota meter
Reading LPM
Flow rate (turbine flow
meter)
Pulse/ sec
Rise of water
level in collecting
tank
Time for 'r' cm
rise of water in collecting tank
Actual discharge
Deviation (Qcal – QT)
TQ in LPM R in cm in sec calQ in
LPM
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Turbine Flow Meter 3
tRA
Qcal
100
60000= LPM.
Where, R is the rise of water level in collecting tank in ,cm
t is the time for R ,cm rise of water rise in collecting tank in sec
PRECATIONS :
Reading should be taken without any parallax error
Each time before starting the experiment initial setting is must
MODEL GRAPHS:
Draw a graph between Q T Vs calQ
Draw a graph between Q T Vs Deviation
Draw a graph between Q T Vs rotameterQ
RESULT:
calQ
Q T
rotameterQ
Devia
tio
n
Q T
Q T
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Kaplan Turbine
KAPLAN TURBINE
AIM:
Determine the efficiency of Kaplan Turbine at constant head
APPARATUS:
Kaplan turbine test rig, tape and hook gauge
THEORY
Hydraulic (or Water) turbines are the machines, which use the energy of
water (Hydro-Power) and convert it into mechanical energy. Thus the turbines
become the prime mover to run the electrical generators to produce the
electricity, Viz, Hydro-electric power.
The turbines are classified as Impulse & Reaction types. In impulse
turbine, the head of water is completely converted into a jet, which impulses the
forces on the turbine. In reaction turbine, it is the pressure of the following water,
which rotates the runner of the turbine. Of many types of turbine, the pelton
wheel, most commonly used, falls into the category of impulse turbines. While
Francis & Kaplan falls in category of reaction turbines.
Normally, Pelton wheel (impulses turbine) requires high head & low
discharge, while the Francis & Kaplan (reaction turbines) require relatively low
heads and high discharge. These corresponding heads and discharges are
difficult to create in laboratory size turbine from the limitation of the pumps
availability in the market. Nevertheless, at least the performance characteristics
could be obtained within the limited facility available in the laboratories. Further,
understanding various elements associated with any particular turbine is possible
with this kind of facility.
DESCRIPTION:
Kaplan turbine, the reaction type which is of present concern consists of
main components such as propeller (runner) scroll casing and draft tube.
Between the scroll casing and the runner, the water turns through right angle into
axial direction and passes through the runner and thus rotating the runner shaft.
The runner has four blades, which can be turned about their own axis so that the
angle inclination may be adjusted while the turbine in motion. When runner blade
angles are varied, high efficiency can be maintained over wide range of operating
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Kaplan Turbine
conditions. In the other words even at parts loads, when a low discharge is
following through the runner, a high efficiency can be attained in case of Kaplan
turbine, whereas this provision does not exist in Francis and propeller turbines
where, the runner blade angles are fixed and integral with hub.
The actual experimental facility supplied consists of a centrifugal pump
set, turbine unit, sump tank, notch tank arranged in such a way that the whole
unit works on re circulating water system. The centrifugal pump set supplies the
water from the sump tank to the turbine through gate valve, which has the
marking to the meter the known quantity of water. The water after passing
through the turbine units enters the collecting tank through the draft tube. The
water then flows back to the sump tank through the notch tank with copulate
notch for the measurement of flow rate. Additionally, the provision is also made to
estimate the rate of flow of water using the “Bend Meter “.
Electrical AC generator connected to lamp tank achieves the loading of the
turbine. The provision for; measurement electrical energy AC voltmeter and
ammeter turbine speed (digital RPM indicator), Head on the turbine (pressure
gauge), are built-in on to the control panel.
SPECIFICATIONS:
Supply Pump / Motor Capacity : 10 hp 3 ph, 440V, 50Hz, AC.
Turbine : 150 mm dia. Propeller with fourblades.
Run-away speed : 2500 rpm (approx.).
Max. Flow of water : 2500 1pm (approx.).
Max. Head : 10 mts. (approx.).
Loading : AC generators
Provisions : Flow rate by Rectangular notch, Notch,
dC = 0.6 (assumed).
Pressure gauge of range : 0 – 2 2cmkg
Vacuum gauge : 0-760 mm of Hg
Electrical load : change by toggle switch (maximum
Connected load: 2000 watts).
Electric Supply : 3 ph, 440V, AC, 30A, with Neutral& Earth.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Kaplan Turbine
PROCEDURE:
1. Keep the gate closed.
2. Keep the electrical load at maximum, by keeping all the switches at ON –
position.
3. Press the green button of the supply pump starter and then release.
4. Slowly, open the gate so that turbine rotor picks up the speed and Attains
maximum at full opening of the gate.
5. Note down the voltage and current, speed, pressure, vacuum on the
control panel, head over the notch, and tabulate results.
6. Close the gate & then switch off the supply water pump set.
7. Follow the procedure described below for taking down the reading for
evaluating the performance characteristics of the Kaplan turbine.
TO OBTAIN CONSTANT SPEED CHARACTERISTICS:
(Operating Characteristics)
1. Keep the gate opening at maximum.
2. For different electrical loads on turbine / generator, change the gate
position, so that the speed is held constant. Say at 1500 rpm. See that
the voltage does not exceed 250V to avoid excess voltage on Bulbs.
3. Reduce the gate opening setting to different position and repeat (2) for
different speed 1500 rpm, 1000 rpm and tabulate the results.
4. The above readings will be utilized for drawing constant speed
characteristics
i. Percentage of full load Vs Efficiency.
ii. Efficiency and BHP Vs Discharge characteristics.
TO OBTAIN CONSTANT HEAD CHARACTERISTICS:
(Main Characteristics)
1. Select the guide vane angle position.
2. Keep the gate closed, and start the pump.
3. Slowly open the gate and set the pressure on the gauge.
4. For different electrical loads, change the rotor pitch position and maintain
the constant head and tabulate the results given in Table – II.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Kaplan Turbine
TO OBTAIN RUN-AWAY SPEED CHARACTERISTICS:
1. Switch OFF the entire load on the turbine and the voltmeter.
2. Keep propeller vane angle at optimum position (Head, h = 0.75 2cmkg
)
3. Slowly open the gate to maximum and note down the turbine speed. This
is the run-away speed, which is maximum.
NOTE : Run-away speed is also influenced by the tightening in gland packing
of the turbine shaft. More the lightness, less the run-away speed
PERFORMANCE UNDER UNIT HEAD – UNIT QUANTITIES:
In the order to predict the behavior of a turbine working under varying
conditions and to facilitate the comparison between the performances of the
turbines of the same type but having different outputs and speeds and working
under different heads, it is often convenient to express the test results in the
terms of certain unit quantities.
.
Unit Speed, uN = HN
Unit Power, uP = 3 H
P
Unit Discharge, uQ = H
Q
PRECAUTIONS:
1. Do not start pump set if the supply voltage is less than 300V
2. To start and stop the supply pump, always keep Gate closed.
3. Gradual opening and closing of the Gate Valve is recommended for
smooth operation.
4. Fill the water enough so that the pump does not choke.
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
Kaplan Turbine
OBSERVATIONS:
Energy meter constant = 1200 kwh
vRe
Width of rectangular notch :b = 0.498 m
Efficiency of generator ` = 70%
CALCULATION:
Delivery Pressure, P = kg / cm2
Suction Pressure, vP = mm of hg
Head on the turbine , Th =
76010
VP m of water
Energy meter revolutions, n =
Time for ‘n’ revolutions of Energy meter, mt = sec
Head over Notch, h = m
Discharge, Q a = 2
3
23
2hgCd m3/ Sec.
Hydraulic Input, hydP = 1000
ha TQW . . …KW
Turbine (Electrical) Output, electP = mtK
n
3600 KW
Turbine Output , shaftP = 7.0
elecPKW
Efficiency = 100hyd
shaft
P
P
Unit Speed, uN = HN =
Unit Power, uP = 3 H
P =
Unit Discharge, uQ = H
Q =
Kaplan Turbine
S.No
.
Turbine Speed, N, rpm
Head on Turbine Net Head
on Turbine ‘Th , m of water
Head over
Notch
’h’ in m of water
Discharge (Flow Rate)
‘Qa’
sec
3m
No. of Bulbs
on
No. of Revolution of energy meter, n
Time for n revolution of energy
meter, t sec.
Hydraulic input power
KW
Turbine Electrical
output BPelcl
Turbine output
BPshaft
100hyd
shaft
P
P
Pressure ‘P’ in
2cmKg
Vacuum ‘Pv’ in
ofmm
gH
Constant Head Characteristics
Kaplan Turbine
Turbine Speed in
RPM
Head on Turbine
Net Head on Turbine
‘H’ in mts
Head over
Notch (Flow Rate), ’h’ in mts
Discharge (Flow Rate)
‘Q’ in sec
3m
Load on Generator
Wattage of Bulb in action
Energy meter
reading Time For 5 Rev in sec
hydHP BHP % tur Pressur
e ‘P’ in
2cmKg
Vacuum ‘Pv’ in
ofmm
gH
‘V’ Volts
‘I’ Amps
Constant Speed Characteristics
GUDLAVALLERU ENGINEERING COLLEGE FM & HMS LAB
KaplanTurbine
121
Net Head on
Turbine
‘H’ in mts
Unit Speed
uN
Unit Power
uP
Unit
Discharge
uQ
Specific
Speed
sN
% tur
GRAPHS:
1. Unit Speed Vs
2. Unit Speed Vs Unit Output power
3. Unit Speed Vs Unit Discharge
RESULT
The efficiency of Kaplan Turbine at constant head =____
Unit Quantities Under Unit Head