595-283-E2009-11-09
Sun Odyssey 39/41/42 Spinnaker Lift Kit
Boat Section B
S.O. 39 C227 15S.O. 41/42 C245 35
S.O. 39 F228 35S.O. 41/42 F246 35
1. Mark the position of the holes for the loop. Use a tape measure for dimension B.2. Adjusttheloopinaviceacc.tothefigure.Thereshould be a total play of about 5 mm between the loop and the mast.3. Check that the loop does not interfere with deck hardware etc.4. Drill two Ø 6.5 holes. Fit the plastic washers between the loop and the mast and rivet the loop to the mast. Punch out the mandrel heads.5. Drill and tap the M8-holes (c/c 20 mm) for the support. Applylockingadhesivetothescrewsandfitthesupportwith the two holes washer.6. Markthepositionforthecleataccordingtofig.1.7. Drill Ø 5 holes and tap the holes for the two M6 screws.8. Fit the cleat with the screws.9. Markthepositionfortheblockaccordingfig.1.10. Drill holes for the block Ø 4.2.11. Fit the block with M5 screws (1xM5x35, 2xM5x20).12. Remove the lower end stop of the track.13. Fit the spinnaker pole slider onto the track.14.Refittheendstop.
CAUTION: Cables and halyards inside mast.Toavoiddamagewhendrillingholes,useadepthstopperonthedrill bit.
200
B350
B-line
www.seldenmast.com
300 25
200
40
Included PartsQuantity Description
511-554-03 1 Spinn pole slide405-001-17 1 Cheek block162-020 1 Screw M5x35155-629 2 Screw M5x20511-016 1 Cleat155-610 2 Screw M6x16508-090 1 Loop164-002 2 Washer, Nylon167-002 2 Pop rivet Ø 6.5530-268 1 Stop/support155-611 2 Screw M8x25164-408 1 Washer, two holes611-009 1 Rope595-283-E 1 Instruction
Tools needed for assembly:Drill bit Ø 4.2, Ø 5 and Ø 6.8PoprivetgunScrewdrivers,TORXTapemeasureM5,M6andM8tappingtool
Fig. 1Fig. 2
Fig. 3
1(1)
595-154-E 2005-10-06
Loop and Support Kit No. 508-090-02. Instructions for assembly.
SectionDimension A B C
C175 200 B 350 C193 200 B 350 C211 200 B 350 C227 200 B+15 350 C245 200 B+35 350 C264 200 B+50 350 C285 200 B+80 350 F176 200 B-10 350 F194 200 B-10 350 F212 200 B-10 350 F228 200 B+35 350 F246 200 B+35 350 F265 200 B+50 350 F286 200 B+80 350
SectionDimension A B C
155/104 150 B 350 170/115 100 B 350 177/124 100 B 350 189/132 100 B 350 206/139 100 B 350 224/150 100 B 350 237/162 100 B 350 190/94 190 B+15 350
213/104 190 B+15 350 235/116 190 B+10 350 232/126 190 B+45 350 260/136 100 B+25 350
1. Mark the position of the holes for the loop. Use a tape measure for dimension B.
2. Adjusttheloopinaviceacc.tothefigure.Thereshouldbeatotal play of about 5 mm between the loop and the mast.
3. Check that the loop does not interfere with deck hardware etc. 4. Drill two ø6.5 holes. Fit the plastic washers between the loop and
the mast and rivet the loop to the mast. Punch out the mandrel heads.
5. Drill and tap the M8-holes (c/c 20 mm) for the support. Apply lockingadhesivetothescrewsandfitthesupport.
CAUTION: Cables and halyards inside mast. Toavoiddamagewhendrillingholes,useadepthstopperonthedrillbit.
A
C
B
B-line
X
C
B +
B-
B-line B