DRIP EZE® LANDSCAPE DRIP TUBE
The discreet brown tubing applies water at a slow consistent rate, minimising run-off and water wastage. Drip Eze is ideal for high density planting areas, intricately shaped landscape beds, median strips and garden beds where overspray cannot be tolerated and can be mulched without loss of flow.
4mm and 13mm ID Tube Drip Eze is available in 4mm and 13mm tube to suit a variety of landscape applications. Use with Australian standard poly fittings.
Classic & Pressure CompensatingSelect from classic (NPC) or pressure compensating (PC) tube to suit the landscape requirements. PC provides even water application over steep and undulating terrain and allows for longer runs.
1.6 Lph, 2 Lph and 8 Lph Flow RatesDrip Eze applies water slowly to penetrate the root zone. Select from a range of spacings to suit your requirements.
Clog minimisationTwo directly opposed outlet holes minimise chance of clogging.
Visible EmitterThe clearly visible emitter is easily aligned with plants for targeted watering and can be avoided when cutting through the tube, making it easier to insert the poly fittings.
FEATURES & BENEFITS
13mm lilac tubing for use with non-potable water. Available in classic and pressure compensating.
Marked “Caution not for drinking”
Select from 4mm or 13mm tubing to suit a range of applications. 13mm available in both classic and
pressure compensating.
Ideal for sandy soils and high density plantings, high flow 8 Lph classic drip tubing.
Drip Eze®
Quickdrip™
Enviro-Drip®
RingSnake
Use a 13mm End Plug to seal the end of the Drip Eze. Use hold down stakes to keep the Drip Eze in place.
Grid
TIP: Flush the Drip Eze before 1st use to clear any debris that may have entered the tube during installation.
Adding an in-line tap allows you to flush the lines.
TYPICAL INSTALLATION METHODS
1300 130 898 toro.com.auCompany policy is one of constant improvement and therefore changes in specifications may be made without notice and without incurring liability.
SPECIFICATIONS
Drip Eze Enviro-Drip Quickdrip
4 mm NPC 13 mm NPC 13 mm PC 13 mm PC 13 mm PC 13 mm NPC
Tube inside diameter 4 mm 13 mm 13 mm 13 mm 13 mm 13 mm
Tube outside diameter 6 mm 15.4 mm 15.4 mm 15.4 mm 15.4 mm 15.4 mmDischarge rate @ 100 kPa 2.0 Lph 2.0 Lph 1.6 Lph 2.0 Lph 2.0 Lph 8.0 Lph*
Emitter Spacing (cm) 15, 30 30, 40, 50, 60, 100 40 30, 40, 50, 60, 100 30 30
Recommended operating pressure range
100 kPa 100 kPa 100 - 300 kPa 100 - 300 kPa 100 - 300 kPa 100 - 300 kPa
Tube pressure rating 300 kPa
Roll lengths (m)25, 50, 100, 200 and
91420, 50, 100, 200 50, 100, 200 20, 50, 100, 200 50, 100, 200 50, 100
Recommended filtration Minimum 120 mesh screen
Note: Not all spacings available in all roll lengths. Contact your Toro Representative for more information. *Quickdrip discharge rate at 200 kPa.
MAXIMUM RUN LENGTHS
ProductFlow Rate
(Lph)Emitter Spacing
Run Length (m)120 kPa Input
Run Length (m) 200 kPa Input
Run Length (m) 300 kPa Input
4mm NPC**2 0.15 4.5
2 0.30 8
13mm NPC**
2 0.30 602 0.40 752 0.50 852 0.60 1002 1.00 1508 0.30 22
13mm PC
1.6 0.40 100 1252 0.30 70 852 0.40 90 1052 0.50 110 1352 0.60 125 1602 1.00 200 255
13mm Enviro-Drip PC 2 0.30 70 85
Note: All pressure compensating tube run lengths are based on a minimum operating pressure of 100 kPa, single laterals and flat ground. **All non-compensating tube run lengths are based on a variation in discharge of± 10% of the nominal dripper flow rate, single laterals and flat ground.
Automatic
Solenoid Valve Nut & Tail
LD Poly Pipe
Pressure Reducing Filter 1011680/1011681
Irrigation controller tuns Drip Eze on and off.
Connect Drip Eze line to home irrigation system for automated watering.
Manual
Connect a manual or automatic tap timer to the tap, for greater watering control.
Turn Drip Eze system on and off from the garden tap.
Nut &
Tail
LD Poly Pipe
Barbed Elbow
Pressure Reducing Filter 1011680/1011681
DRIP EZE® LANDSCAPE DRIP TUBE
CONNECTION TO THE WATER SUPPLY
For best results, connections should always be secured with locking clamps.
PVC or
MDPE pipe