1
TRACK MAKING
EVAGLIDE CORDED CONTRACT
Version 1.0
For more guides and videos visit www.evans-textiles.com/resources
2
Here to help
At Evans, we understand the importance of getting things right for you and your clients.
That’s why we’ve put together this easy to follow step-by-step guide to help make things
easier for you.
In this guide we’ll cover product types, assembly information and chronologically set out
the instructions on how to put the product together. The guide is part of the ‘Evans
Difference’ giving our customers expert support which is designed to be easy to follow
and hassle free.
For more guides and videos visit www.evans-textiles.com/resources
3
STEP 1, TRACK TYPE: -
Check track colour.
STEP 2, TRACK SIZE: -
Cut Track to specified size.
STEP 3, CORD LENGTH: -
Check overall cord length including drop and cut.
IMAGE 1 (780025A TRAVERS CORD)
STEP 4, CORD SIDE: -
Corded right side, Corded left side, Corded both.
For more guides and videos visit www.evans-textiles.com/resources
4
MID STACK RIGHT OP MID STACK LEFT OP
PART 5, CARRIER TYPE: -
Check carrier type and feed in to the track as below, if the carriers are wave, flex or fold they must be
an even number.
780073 OFFSET CARRIERS 783073 WHEELED CARRIER
PART 6, OVERLAP & UNDERLAP: -
See below,
780099 (OVERLAP) 780100 (UNDERLAP)
For more guides and videos visit www.evans-textiles.com/resources
5
PART 7, ENDCAP TYPE: -
Long end pulley for pairs of curtain, long and short pulley for single stack curtain which the long pulley
on the corded side.
780094 BOTH SIDES FOR A PAIR 780094 AND 781151 FOR LEFT OP 781151 AND 780094 FOR RIGHT OP
TRACK ASSEMBLEY MID STACK CURTAIN, RIGHT OP IF LEFT HAND OP WORK FROM THE LEFT SIDE OF
THE TRACK: -
Once all components have been picked feed the cord through the cord holes is the cord pulley (see
image 1), then feed the cord in to the track ensuring it is in the cord channels correctly (see image 2)
and pull all the way to the other side of the track, once the cord is completely in the track apply the
double cord connector to the string furthest away from you and do not fasten (see image 3)
IMAGE 1 (780094 PULLEY) IMAGE 2 IMAGE 3 (780093 CORD CONNECTOR)
Then feed cord connector in to the underlap and feed in to the track ensure the cord connector enters
the cord channel (see image 4, 5 and 6)
IMAGE 4 (780100 underlap) IMAGE 5 IMAGE 6
For more guides and videos visit www.evans-textiles.com/resources
6
Once the underlap is in the track then feed on the carriers, ensure the flat edge of the carrier lines up
with the flat edge of the underlap ( see image 7). Then push on the endcap (see image 8)
IMAGE 7 IMAGE 8
Then go to the opposite side of the track and apply a cord connector to the bottom cord and screw this
down in to place (see image 9, 10)
IMAGE 9 IMAGE 10
Then feed the cord through the right hand pulley (see image 11), then add a short cord connector DO
NOT SCREW DOWN (see image 12)
IMAGE 11 (780094) IMAGE 12 (910093 CORD CONNECTOR)
Feed the first cord connector (see image 10) in to the overlap (see image 13) and feed the first half in
to the track. Then feed the cord through the back gap of the overlap and hold the cord connector in
place (see image 14), then push the overlap and the cord connector in to the track ensuring the cord
connector goes in to the cord channel.
For more guides and videos visit www.evans-textiles.com/resources
7
IMAGE 13 (780099 OVERLAP) IMAGE 14 IMAGE 15
Then feed in the carriers and push on the endcap (see image 16)
IMAGE 16
To set the cord drop choose your cord length and set this on the tape measure i.e. 20cm cord and line
the 20cm section on the tape with the end of the track (see image 17), make sure all the carriers,
overlap and underlap are pulled back in to the fully open position then pull the cord up through the
overlap see image 18, keep pulling until the end of the cord is lined up with the end of the tape (see
image 17)
IMAGE 17 IMAGE 18
For more guides and videos visit www.evans-textiles.com/resources
8
Then screw down the first cord connector on the opposite site to the cord operation (see image 19), then
screw down the end pulley (see image 20)
IMAGE 19 IMAGE 20
Then move back to the cord side and screw down the end pulley (see image 21), then screw down the
cord connector in the overlap (see image 22). Before cutting the cord test the track works by pulling the
cord in the control side unit the overlap underlap meet, then pull in the opposite direction until they are
back in the open position.
IMAGE 21 IMAGE 22
Once the track has been tested and works cut the excess cord and leave it around 3-4 inches long (see
image 23), then use a lighter to burn the end of the cord and push it together with your fingers (see
image 24) be very carful not to burn your fingers.
IMAGE 23 IMAGE 24 IMAGE 25
For more guides and videos visit www.evans-textiles.com/resources
9
TRACK ASSEMBLEY SINGLE STACK OR DUAL: -
Once all components have been selected feed the cord through the cord holes is the cord pulley (see
image 1), then feed the cord in to the track ensuring it is in the cord channels correctly (see image 2)
and pull all the way to the other side of the track, once the cord is completely in the track add the end
cap (see image 3), then turn the track over and screw the endcap in place (see image 4)
IMAGE 1 (781150 SMALL PULLEY) IMAGE 2 IMAGE 3
IMAGE 4
Then go to the opposite side of the track and apply a cord connector to the bottom corded and crew this down in to place
(see image 5, 6)
IMAGE 5 IMAGE 6
For more guides and videos visit www.evans-textiles.com/resources
10
Feed the first cord connector in to the overlap (see image 7) and feed the first half in to the track. Then
feed the cord through the back gap of the overlap and hold the cord connector in place (see image 8),
then push the overlap and the half cord connector in to the track ensuring the cord connector goes in to
the cord channel.
IMAGE 7 (780099 OVERLAP) IMAGE 8 IMAGE 9
Then feed in the carriers and push on the endcap (see image 10)
IMAGE 10
To set the cord drop choose your cord length and set this on the tape measure i.e. 20cm cord and line
the 20cm section on the tape with the end of the track (see image 11), make sure all the carriers,
overlap and underlap are pulled back in to the fully open position then pull the cord up through the
overlap (see image 12), keep pulling until the end of the cord is lined up with the end of the tape (see
image 12)
IMAGE 11 IMAGE 12
For more guides and videos visit www.evans-textiles.com/resources
11
Screw down the end pulley (see image 13), then screw down the cord connector in the overlap (see
image 14). Before cutting the cord test the track works by pulling the cord in the control side unit the
overlap underlap meet, then pull in the opposite direction until they are back in the open position.
IMAGE 13 IMAGE 14
Once the track has been tested and works cut the excess cord and leave it around 3-4 inches long (see
image 15), then use a lighter to burn the end of the cord and push it together with your fingers (see
image 16) be very carful not to burn your fingers.
IMAGE 15 IMAGE 16 IMAGE 17
For more guides and videos visit www.evans-textiles.com/resources
12
BRACKET TYPE: -
Check to see if this is top fixed brackets or wall fixed. If wall fix check the bracket length.
780007 (STANDARD CEILING BRACKET) 783339 (CONCEALED CEILING BRACKET) 783012 (TOP FIX BRACKET WITH CAP)
780010 (3.5CM WALL BRACKET) 780011 (6CM BRACKET) 780012 (7.5CM BRACKET)
780013 (10CM BRACKET) 780014 (15CM DOUBLE BRACKET) 780015 (25CM TRIPLE BRACKET)
781022 (7-11CM ADJUSTABLE WALL BRACKET) 783997 (COVER CAP)
For more guides and videos visit www.evans-textiles.com/resources
13
FLEX, WAVE, and FOLD TAPE: - See Paul Naughton for tape calculations.
FLEX AND WAVE TAPE FOLD TAPE 15.75CM
FOLD TAPE (ORDINARY) 10.75CM FOLD TAPE (XL) 15.75CM
***PLEASE NOTE ALL NOTES ALL CODES ABOVE ARE FOR WHITE TRACKS
IF COLOUR VARIES PLEASE SEE TEAM LEADER FOR GUIDANCE***
For more guides and videos visit www.evans-textiles.com/resources
14
***BEFORE PAKCAGING TICK OFF EACH ITEM TO MAKE SURE NO STEPS
HAVE BEEN MISSED AND NO ITEMS ARE MISSING***
…and that’s it! You’re finished!
STEPS COMPLETE? Please tick
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
For more guides and videos visit www.evans-textiles.com/resources
15
Evan Textiles (Sales) Ltd, Helmet Street, Manchester, M1 2NT
Registered in England No. 6186585 Part of the Evans Group of Companies