aylorDynamometer
TD-24-AC / Chassis Dynamometer
Total Test Success
TD-24-AC Chassis Dynamometer
SpecificationsWeight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 39,400 lb (17,872 kg)Capacity: 1,034 hp at 30 mph (771 kW at 48 kph)Rolls: 24 by 34 in. (610 by 864 mm) long, 4 front fixed rolls, 2 rear rolls to accommodate axle spreads from 48 to 66 in. (1,219 to 1,676 mm) tandem centersPit Required Depth: 26 in. (660 mm)
Recommended Accessories• Hood Style Exhaust System• Horizontal Exhaust• Calibration Weights• Wheel Chocks• Stone Guard• Guard Rail• Load Bank or Regenerative Feedback• DynPro2 Data Acquisition & Control System
(414) 755-0040 www.taylordyno.com 2
TD-36-AC shown above
Optional Hood Style Exhaust System
Optional Stone Guard
OptionalWheel Chocks
OptionalHood Style Exhaust System
OptionalCalibration Weight Kit
(414) 755-0040 www.taylordyno.com 3
050
100150200250300350400450500550600650700750800850900950
100010501100115012001250
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90
Hor
sepo
wer
(HP)
MPH
TD-24-AC Power Curve, English
050
100150200250300350400450500550600650700750800850900950
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145
Kilo
wat
ts (k
W)
KPH
TD-24-AC Power Curve, Metric
(414) 755-0040 www.taylordyno.com 4
Infared Space Heater
Infared Space Heater
Optional Horizontal Exhaust
Center Line of Truck
Rolls,/& Canopy
Hood Style Exhaust
Floor Drain
HVAC Controller
Note:Vehicle length should be considered before determining the length of the test cell to be constructed.
aylorDynamometer
3602 West Wheelhouse Road, Milwaukee, Wisconsin 53208 U.S.A.(414) 755-0040 www.taylordyno.com SMS3012v002
Everything you need to succeed
SpecificationsWeight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 39,400 lb (17,872 kg)Capacity: 1,034 hp at 30 mph (771 kW at 48 kph)Rolls: 24 by 34 in. (610 by 864 mm) long, 4 front fixed rolls, 2 rear rolls to accommodate axle spreads from 48 to 66 in. (1,219 to 1,676 mm) tandem centersPit Required Depth: 26 in. (660 mm)
Drawing Notes(a) Refer to appropriate Taylor Foundation (“Pit”) drawing - drawing dimensions are for use as layout guidance only. AC power,
air and water required at one side wall.
(b) Room length, and pit location within length, must be determined by user to fit his maximum truck length and rear overhang.
(c) Provide at least one mandoor for fire escape near rear of room, but not in rear wall because someone entering during a test
could be struck by a stone flung from a tire. Provide ample fire extinguishers at each door and near driver.
(d) “Back-on, Drive-off” installation configuration is preferred.