Dynamic Modeling of Reciprocating Compressors with Vertical Axis
P R. G. Kurka1, Karen L. G. Paulino
2, Jaime H. Izuka
1
1Faculty of Mechanical Engineering, University of Campinas (UNICAMP)
P.O. Box 6122, 13083-970 Campinas, SP, Brazil
Tel.: +55 19 3521 3175; fax: +55 19 3289 3722.
email: [email protected]
email: [email protected]
2 Department of Science and Earth Studies
Federal University in São Paulo - UNIFESP
R. Prof. Artur Riedel, 275, 09972-270, Diadema, SP, Brazil
email: [email protected]
Abstract The paper presents the dynamic model of a reciprocating compressor with vertical axis. The model
consists of a rotor, crankshaft, connecting rod and piston, all supported by visco-elastic bearings. The
model incorporates the gyroscopic interactions due to the movement of the bearings of rotating
components. The Newton-Euler method is used in the analysis, establishing the necessary differential
equations that describe the movement of the system. Analysis of the flexible bearing model shows that
oscillations of the rotating internal components of the compressor increase the loads of the bearings, as
compared to the support loads of non-flexible bearing models.
1 Introduction
Reciprocating compressors use a crankshaft mechanism to convert the rotor axis rotation into piston
translation. The compressor moving parts are supported by hydrodynamic bearings, whose lubrication is
maintained by means of a helicoidal/centrifugal pump. Compressor lifetime and performance is highly
affected by the lubrication of its moving parts. An inefficient or inadequate lubrication of the moving parts
may lead to equipment failure or waste of energy [1] and [2]. The hydrodynamic supports cause a
secondary displacement of the rotor components in the radial direction of the bearings. The numerical
simulation of such an operational behavior, through a dynamics analytical model that includes the
secondary radial movements, yields a realistic estimation of the forces supported by the bearings. Accurate
estimation of bearing loads is an important aspect to the design and performance of reciprocating
machines and mechanisms. The o objective of the present work is, therefore, to obtain a detailed
numerical model of the dynamics of a single cylinder, reciprocating refrigeration compressor [3] with
flexible bearings.
The performance of refrigerating compressors, due to the dynamics of its driving system, connecting rod
and piston, together with bearing lubrication effects, has been researched, by Prata [4], Cho [5] and Kim
[6], and Goodwin [7], among others. The works show that optimization of the bearing forces improve the
performance, lifetime and reliability of the system. An efficient dynamic model allows for better results in
the solution of the coolant fluid compression/expansion effects, better parts design, and contribute to the
knowledge database for research on NVH requirements and compressor lubrication performance [8] and
[9].
1573
The necessity of a method to predict the entire compressor movement is highlighted by Dufour et al. [10].
A dynamic slider/crank model is proposed to study the transient and steady state behavior of a single
cylinder compressor. A numerical analysis for a reciprocating compression mechanism is performed by
Kim and Han [6], which considers the coupled dynamic behavior of the piston and crankshaft. Prata et al.
[4] present a numerical investigation for a piston inside the cylinder in a small hermetic compressor, with
the radial clearance between piston and cylinder filled with lubricant oil. The effects of some design
parameters and operating conditions are examined; with regards to the stability of the piston, oil leakage
and friction losses. Emphasis is placed on the investigation of the influence of the pin location, radial
clearance and oil viscosity on the piston dynamics. The piston dynamics is also investigated by Cho and
Moon [5]. In this research the crankshaft and connecting rod is included in the model to represent the
transformation of the rotating motion to a reciprocating translation of the piston.
The sensitivities to dimensional tolerances in reciprocating engine dynamics is researched by Sinha, et al.
[11], for an internal combustion engine. Such an engine model is governed by a nonlinear differential
equation with a discontinuous forcing function, due to the nature of the pressure-volume (P-V) diagram.
The differential equation of motion comes from the kinematic equations of the slider/crank mechanism. A
single-cylinder engine model with flexible crank support is proposed by Goudas et al. [12]. Transient and
steady state dynamic response of a class of slider/crank mechanisms with compliant supporting is
investigated. The attention is focused on investigating the influence of the system parameters on its
dynamics.
All the above mentioned works use a simplified dynamic model of the rotor-connecting rod-piston model,
which does not account for the gyroscopic effects that take place due to the orbital movement of the
rotating components in their bearing cases. The model proposed in the present work introduces such a
behavior, considering as a first approach, the existence of linear elastic bearings. The formulation and
simulation results found in such a model can be easily exported to more realistic bearing behavior,
including the coupled hydrodynamic effects of non-linear stiffness and damping.
The dynamic efficiency of the compressor is affected by operational misalignments. The alignment of
rotor supports, for example, has a great influence on the behavior of rotating machinery [13]. The
dynamical models must be able to quantify the increase of bearing loads as a result of misalignments. A
gap is observed in the literature, with respect to such a dynamic study, since the models available address
only the more simplified aligned or pinned behavior of the bearings. Current models, which are used with
commercial software, are based on constrained or pinned movements of the bearings of axis, connecting
rod and piston. The misalignments introduced due to bearing flexible movements cannot be verified in
such models. In the present modeling proposal, the rotational movement of compressor parts are
described, based on Euler’s angles, comprised of precession, nutation and spin ([14] and [15]). Three
local reference frames are defined, in addition to the inertial coordinates system, whose origins are placed
at the center of mass of the compressor parts (axis, connecting rod, piston).
The bearing reactions are modeled as elastic and viscous forces, which represent the hydrodynamic loads
produced by the relative displacement between the bearings and their casing. External loads come from
the driven torque and the cooling gas pressure on the piston [16]. All parts are considered rigid and the
distance between the bearings is not long enough to produce relevant elastic bending of the elements. The
basic analysis consists on establishing the balance of forces in the piston due to the cylinder pressure
variation, to determine the connecting rod reaction force and consequently the loads in the eccentric
(crankshaft) and compressor axis. The dynamic behavior of the model is based on a numerical simulation
through a fourth order Runge-Kutta method, using the Matlab environment. The computational code
simulates the compressor dynamics under constant operational speeds, allowing for the study of the
influence of different constitutive models of loads that act on the bearings.
2 Description of the model
The reciprocating compressor main parts are the compressor housing, axis, cylinder, connecting rod,
piston and discharge valves, shown in Figure 1. The housing protects the driving elements, moving parts
1574 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
of the compressor and functions also as a lubricant reservoir, since the oil is stored in its lower region.
The lubricating system consists of an oil pump, oil filter and oil cooler.
Figure 1: Representation of reciprocating compressor [17].
The driving element is the axis, which is attached to an electric rotor. The driven elements are the
connecting rod, which is positioned eccentrically to the axis and converts the rotating movement into a
reciprocating translation; and the piston, which is connected to the rod through a pin, and whose
reciprocating movement compresses the cooling gas into the cylinder.
The axis is supported by hydrodynamic bearings: the primary and secondary radial bearings and a vertical
(axial) weight supporting bearing, all attached to the compressor block. The axial bearing is not
considered in the present model, since the most important secondary movements take place in radial
directions. Another hydrodynamic bearing is located at the axis eccentric connection point. Such a
bearing is responsible to the eccentric attachment of the axis to the connecting rod. An articulated pin
attaches the connecting rod to the piston. The small dimensions of the articulated pin connection, when
compared to the dimensions of the remaining components bearings, allow the use of a non flexible force
transmitting element, rather than a hydrodynamic bearing in the analysis. The main piston movement
takes place in the axial direction, but small displacements also occur in the radial directions. For this
reason, two flexible sliding bearings are defined at the piston top and skirt regions, which represent the
actuating points of the forces that cause radial displacements.
2.1 Components
Four reference systems are created for the analysis: an inertial and three local ones, each one of them
located in the center of mass of the compressor components. The motion of the rotor is described by five
movements: two absolute displacements of its center of mass, xr, yr, and three Euler rotations: precession
r, nutation r and spin r. Four movements are considered in describing the motion of the connecting
rod: two absolute displacements of its center of mass, xc, yc, and two Euler rotations: nutation c and spin
c. Four movements are considered in describing the motion of the piston: two absolute displacements of
its center of mass, yp and zp and two Euler rotations: nutation p and spin p , all shown in Figure 2.
DYNAMICS OF ROTATING MACHINERY 1575
Figure 2: Inertial System (XYZ), Local System and their rigid body motion and bearing position (1,
2, 3, 4, 5 and 6)
Rotation matrices are used to convert the local coordinates into the inertial frame. The complete rotation
matrix of the rotor is a product of its three individual rotations (r, r and r), Tr = T rTrTr. The
structures of the three rotations matrices are given in equations (1), below.
100
0)cos()sin(
0)(sin)cos(
rr
rr
r
T,
)cos(0)(sin
010
)(sin-0)cos(
rr
rr
r
T,
100
0)cos()(sin-
0)(sin)cos(
rr
rr
r
T (1)
The rotation matrix of the connecting rod is a product of its two individual rotation (c and c), Tc = Tc
Tc . The structures of the three rotation matrices are given in equations (2), below.
)cos(0)(sin
010
)(sin-0)cos(
cc
cc
cT,
100
0)cos()(sin-
0)(sin)cos(
cc
cc
cT (2)
1576 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
For the Piston, the complete rotation matrix is given by the product of its two individual rotations
(p and p) : Tp = Tp Tp. The rotation matrices are shown in equations (3) below.
)cos(0)(sin
010
)(sin-0)cos(
T
pp
pp
p
,
100
0)cos()(sin-
0)(sin)cos(
T pp
pp
p
(3)
2.2 Angular velocity
The angular speed of the compressor’s moving parts can be calculated through differentiation of their
Euler rotations [14] and are defined as:
dt
d0
0
TT
0dt
d0
T
dt
d0
0
r
rrr
r
r
r (4)
0dt
d0
T
dt
d0
0c
c
c
c (5)
0dt
d0
T
dt
d0
0p
p
p
p (6)
2.3 Coupling of elements
Couplings are the constraints given by the operational and geometry characteristics of the different
components of the compressor. The first restriction imposes that the connecting rod is pinned to the piston.
Such a condition is expressed in equation (7) below.
pc (7)
The relative displacement between the centerlines of the rotor’s eccentric’s bearing and the connecting
rod’s bearing, Figure 3, is expressed by 3, that is,
c3gcr3gr3 RRRRΔ (8)
The crankshaft mechanism imposes that the position of the center of mass of the connecting rod, Rgc ,
relates to the position of the center of mass of the piston, Rgp, that is,
c4p4gpgc RRRR (9)
Such a restriction is depicted in Figure 3.
DYNAMICS OF ROTATING MACHINERY 1577
Figure 3: Geometric restrictions of the reciprocating compressor: the variable 3 (eccentricity
displacement) and mass center position of the connecting rod (Rgc).
Two additional geometric constant parameters are the piston’s height, z , with regards to the origin of the
inertial system and the piston’s offset value, given by y.
2.4 Constitutive Equations (Elastic and Viscous Force)
The elastic and viscous forces are proportional to the negative value of the bearing displacement and
velocity, respectively. They are defined trough a stiffness matrix K and damping matrix Ci and are
represented as:
i
i
i
i
k00
0k0
00k
K , i = 1,2,….,6 (10)
i
i
i
i
c00
0c0
00c
C , i = 1,2,….,6 (11)
The values assigned to the stiffness and damping constant are obtained by trial and error, in such a way
that the orbits of all bearings do not exceed the eccentricity limit [19].
2.5 Combined Forces
The constitutive equation for the viscous and elastic bearing forces represented by forces F1, to F3 and F5
to F6 , which index describes the bearing position defined at Figure 2, can be written as :
)()( r1r1gr1r1r1gr11 rRRCrRRKF (12)
)()( r2gr2r2r2gr22 RRCrRRKF (13)
1578 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
33333 ΔCΔKF (14)
gpldp5gp5p5p5gp55 )()y( RCRRCΔrRRKF (15)
gpldp6gp6p6p6gp66 )()z( RCRRCΔrRRKF (16)
Numerical simulations at the end of the paper show the influence on the choice of different damping and
stiffness coefficients for the bearings.
2.6 Equations of motion and their solution
The dynamic equations of motion are obtained from the Newton-Euler equations. Application of such
equations to the rotor yields,
321 FFFRM grr
τFTrFTrFTrωIωωI 3rr32rr21rr1rrrrr (17)
The same equations applied to the connecting rod yields,
c43gcc PFFRM
c_visc4cc43cc3ccccc τFTrFTrωIωωI (18)
Newton-Euler equations applied to the piston yields
pext654gpp PFFFFRM
6pp65pp54pp4ppppp FTrFTrFTrωIωωI (19)
A fourth order Runge Kutta algorithm is used, by means of the MatLab ODE45 toolbox function, to solve
the simultaneous system of differential equations presented in equations (17) to (19).
3 Defining the operational conditions for simulation
3.1 Operating torque
The torque required for maintaining a constant axis rotation is firstly calculated. The bearings are assumed
to be infinitely rigid so that no radial displacement is verified. The operating torque is calculated as a
function of equally spaced angles of rotation of the rotor, along a complete revolution. The driven torque
profile calculated in the pinned system operational condition is used as an input to the flexible system
analysis.
3.2 Flexible System bearing forces and displacements
Actuating loads and displacements of the bearings are calculated using the driving torque profile
computed in the pinned system analysis. The constitutive equations of the bearing displacements provide
the necessary relationship between loads and radial displacements. The constitutive hypothesis for the
bearing force reaction mechanisms are verified in this analysis.
DYNAMICS OF ROTATING MACHINERY 1579
3.3 Gas pressure condition
The gas pressure variation due to the compressor reciprocating movement is extracted from Couto [16]
and is presented in Figure 4 (a)(b). Such a pressure curve is used in the pinned system analysis to calculate
the driving torque which is necessary to maintain a constant angular velocity of the rotor axis.
Figure 4: (a) (b)Gas pressure at compressor cylinder. (c) Driven torque for reciprocating
compressor when submitted to compression loads.
4 Simulation results
Results from numerical simulations are compared, concerning the pinned and flexible systems. This
comparison verifies the relevance of using a complete dynamic modeling in the investigation of the
bearing forces. Different dynamic forces and bearing load conditions are analyzed from the model. The
inertia forces arriving from the movement of the compressor parts, during operation, is analyzed first. The
bearing forces are calculated in the sequence, considering the gas compression load.
The compression load, according to the gas pressure curve described in Figure 4 (a)(b), requires the
calculation of an operational torque to maintain the condition of constant rotor velocity. The torque is
calculated with the hypothesis of pinned bearings and the result is shown in Figure 4 (c).
4.1 Pinned and conservative bearing reaction forces
The bearing loads for the pinned and flexible bearing conditions are shown in Figure 5 and Figure 6. The
bearing stiffness are chosen in such a way as to preserve the maximum allowed eccentricity physical
1580 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
relationship. For this simulation the adopted stiffness are: k1 = 5,0 x 107 N/m; k2 = 4,0 x 10
7 N/m; k3 = 2,5 x
107 N/m; k5 = k6 = 3,0 x 10
7 N/m.
Figure 5: Bearing load at pinned system .
Figure 6: Bearing load at flexible system.
The RMS value of the bearing force is computed, and it is verified that the elastic bearing reaction forces
are higher than those necessary to maintain the pinned dynamics. Figure 7 shows the bearing orbit in the
flexible system.
DYNAMICS OF ROTATING MACHINERY 1581
Figure 7: Bearing orbit at flexible system.
4.2 Bearing force with dissipative force
This simulation considers the calculation of bearing forces that are proportional to its radial velocity
components. A change in the bearing reaction force is verified with the use of such a dissipative model.
The reaction from the dissipative bearing models shows the same regular distribution pattern and modulus
as the reaction forces of the pinned bearing model, as observed in Figure 8.
Figure 8: Bearing load at flexible system.
The viscous components of the bearing reaction forces are one order of magnitude smaller than the elastic
force components. Figure 9 shows the bearing forces of viscous nature.
1582 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
Figure 9: Bearing dissipative load at flexible system.
A more regular bearing orbit for the parametric viscous damping model is shown in Figure 10. This orbit
behavior indicated that the dissipative forces work as a regularization/stabilization control of the bearing
displacement, reducing the additional load generated by its decentralized movement.
Figure 10: Bearing orbit at flexible system.
A summary with the RMS load results for each bearing model are shown in Table 1.
DYNAMICS OF ROTATING MACHINERY 1583
Inertial Load Compressive Load Compressive and Dissipative
Load
Pinned System Flexible
System
Pinned System Flexible
System
Geometric
Dissipation
Parametric
Dissipation
1 160,9 215,6 392,1 528,0 524,1 395,4
2 78,0 164,6 154,6 331,7 329,9 159,5
3 83,6 103,7 239,2 289,9 285,3 240,0
4 4,9 8,6 27,9 40,8 39,3 28,5
5 4,6 6,7 25,6 47,9 45,1 26,1
1,2,3,4,5 – bearing position (1-primary, 2-secondary, 3-eccentric, 4-piston bottom, 5-piston top)
Table 1 – Bearing Loads RMS Value (Newton).
4.3 Orbit comparison with experimental results
The bearing model represented by elastic stiffness and parametric dissipation show the most stable orbit
when compared to the simulations of other bearing conditions. The orbit results for the rotor’s primary
and secondary bearing, using such a parametric dissipation model are plotted in Figure 11. An
experimental orbit measurement for the same bearings of the real compressor, available in [16], is shown
in Figure 12.
Figure 11: Bearing orbit: Simulation results for Primary bearing (red) and Secondary bearing
(blue).
The comparison shows the same stable behavior of the orbits in both simulation and experimental results.
The difference in orbit shapes are due to the arbitrary stiffness and damping values used in the numerical
model, as well as to the model itself, which is a simplification of the true hydrodynamic nature of bearing
forces that take place in the real mechanism. Nevertheless, the simplified stiffness-parametric damped
bearing model allows for the determination of a more realistic behavior of the dynamics that take place on
the mechanism components of the compressor.
1584 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
Figure 12: Bearing orbit: Experimental result from Couto [16].
5 Conclusion
Analysis of the results of simulation using the complete dynamic model of the compressor with oscillation
of the rotating components leads to the following conclusions.
1 – Modeling of undamped oscillations of the axis-crankshaft-piston system produce distinct loads in the
compressor bearing, when compared to the bearing loads obtained with the pinned model.
2- The presence of dissipative forces in the bearings is responsible for the attenuation of secondary
movement in directions other than those necessary to perform the compression cycle. Dissipative forces
are one order of magnitude lower than the elastic forces that take place at the flexible bearings, and are
responsible to keep the bearing force to levels that are similar to those found in the pinned bearing system
model.
3- It is believed that the use of a full hydrodynamic bearing, modeled by Reynolds equation and coupled
with the system dynamics, would bring, for the present system, results that are similar to those calculated
with the pinned model.
4- The proposed model quantifies in a proper way the components displacement in directions that differ
from those necessary to execute the compression cycle. It is believed that such a model has a potential for
more precise calculations of the bearing dissipated energy and maintenance of a more stable compression
cycle.
5- The model can also be successfully employed in the analysis of other compressors and reciprocating
engines whose inertia, velocity or radial gap tolerances may lead to orbital movements that influences in a
more critical way the total load supported by the bearings.
Acknowledgements
The authors wish to thank Brazil´s research support foundation, CNPq for sponsoring this work.
DYNAMICS OF ROTATING MACHINERY 1585
References
[1] Tassou, S. A. e Grace, I. N.; Fault diagnosis and refrigerant leak detection in vapour compression
refrigerant systems. International Journal of Refrigeration, v28 (2005) pp. 680-688.
[2] House, J. M.; Lee, K. D.; Norford, L. K.; Controls and diagnostics for air distribution systems.
Journal of Solar Energy Engineering, Transactions of the ASME, v 125, Emerging Trends in building
Design, Diagnostics, and Operations. 2003.
[3] Stoecker, W. F.; Jabardo, J. M. S.; Refrigeração Industrial, Ed. Edgard Blucher, ed. 2, 2002 [in
Portuguese].
[4] Prata, A. T., Fernandes, J. R. S., Fagotti , F. Dynamic Analysis of Piston Secondary Motion for
Small Reciprocating Compressors. Journal of Tribology, v. 122 (2000) pp. 752-760.
[5] Cho, J.R., Moon, S.J. A numerical analysis of the interaction between the piston oil film and the
component deformation in a reciprocating compressor. Tribology International, 38 (2005) pp. 459–
468.
[6] Kim, T.J., Han, J.S. Comparison of the Dynamic Behavior and Lubrication Characteristics of a
Reciprocating Compressor Crankshaft in Both Finite and Short Bearing Models. Tribology
Transactions, 47 (2004) pp. 61-69.
[7] Goodwin, M. J., Nikolajsen, J. L., Ogrodnik, P. J. Reciprocating machinery bearing analysis: theory
and practice. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering
Tribology, v. 217 (2003) pp. 409-426.
[8] Nunes, O. Theoretical and Experimental Analysis of the Acoustic Filed Irradiated by an Hermetic
Compressor. Master Thesis, State University of Campinas, Campinas 2005 [in Portuguese].
[9] Jeon, J.Y., You, J., Chang, H .I. Sound radiation and sound quality characteristics of refrigerator
noise in real living environments. Applied Acoustics 68 (2006) pp. 1118–1134.
[10] Dufour, R., Hagopian, J. Der, Lalanne, M. Transient and Steady State Dynamic Behaviour of Single
Cylinder Compressors: Prediction and Experiments. Journal of Sound and Vibration, 181(1) (1995)
pp. 23-41.
[11] Sinha, A., Gilmore, B. J., Zhang, F., Kohli, V. Efficient Computation of the Sensitivities of
Reciprocating Engine Dynamics to Dimensional Tolerances. Mechanism and Machine Theory, v. 32,
no. 2 (1997) pp. 241-253.
[12] Goudas, I., Stavrakis, I., Natsiavas, S. Dynamics of Slider-Crank Mechanisms with Flexible Supports
and Non-Ideal Forcing. Nonlinear Dynamics 35 (2004) pp. 205–227.
[13] Vázquez, Jose A., Barrett, Lloyd E., Flack, Ronald D. A Flexible Rotor on Flexible Bearing
Supports: Stability and Unbalance Response. Journal of Vibration and Acoustics - Transactions of
the ASME, v. 123 (2001) pp.137-144.
[14] Shabana, A. A. Dynamics Multibody Systems Illinois: John Wiley & Sons, 1989.
[15] Santos, I. F. Dinâmica de Sistemas Mecânicos – Modelagem – Simulação –Visualização –
Verificação. São Paulo: Makron, 2001 [in Portuguese].
[16] Couto, P. R. C. Análise de Mancais Radiais Hidrodinâmicos com Aplicação em Compressores
Herméticos de Refrigeração. Ph. D. Thesis, Federal University of Santa Catarina, Florianopolis 2006
[in Portuguese].
[17] Wisbeck, H. J. Uma Nova Metodologia de Solução para Sistemas de Mancais Radiais em
Carregamento Dinâmico Incluindo Atrito Sólido e Desgaste. Master Thesis, Federal University of
Santa Catarina, Florianopolis 2000 [in Portuguese].
[18] Fox, R. W., McDonald, A. T. Introduction to fluid mechanics. USA, John Wiley & Sons, 1985.
1586 PROCEEDINGS OF ISMA2010 INCLUDING USD2010
[19] Duarte Jr., D. Tribologia, Lubrificação e Mancais de Deslizamento. Rio de Janeiro, Editora Ciência
Moderna, 2005 [in Portuguese].
DYNAMICS OF ROTATING MACHINERY 1587
1588 PROCEEDINGS OF ISMA2010 INCLUDING USD2010