Floor Warming & Heating Bath ComfortBath Comfort Indoor Comfort Outdoor Control Units
www.domoteck-thermoline.com | [email protected] | +972 4 987-2266
ThermoDomoTeck
F l o o r W a r m i n g & H e a t i n gLine
Simple & Perfect
Our floor warming systems can be easilyand accurately regulated,
providing evenly distributed heatin every room of the house
ThermoDomoTeck
F l o o r W a r m i n g & H e a t i n g
Domoteck ThermoLine (DTL) is a world leading manufacturer of advanced radiant heating systems based on the principle of energy-efficient, low temperature heating.
Domoteck ThermoLine (DTL) also offers a suite of comfort appliances for the home and office aimed at meeting every type of heating requirement. Domoteck Thermoline (DTL) mission is to provide its customers with superior products supported by prompt and professional service.
Line
Domoteck ThermoLine (DTL) has proven time and again that hard floor surfaces, such as ceramic and natural stone, can be more than just beautiful. They can also be cozy, inviting and warm. The natural properties of these surfaces gradually absorb the heat generated by Domoteck ThermoLine mats, adding extra warmth to your home.
Domoteck ThermoLine (DTL) mats are zone-specific heating systems, placed directly under the floor surface. They can be used to supplement any conventional central heating system that fails to heat all areas of the house adequately.
Floor Warming & Heating
Bath Comfort
Indoor Comfort
Control Units
Outdoor
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Low installation costs and rapid heating capabilities make Domoteck ThermoLine heating mats and cables the optimum solution for maximum comfort in the living room and other large rooms. Domoteck ThermoLine floor warming systems are easily and accurately regulated, providing evenly distributed heat in every room of the house, at any time of the day or night.
Domoteck ThermoLine control units are made of high quality raw materials with superior design and consideration of user needs. The standard thermostat incorporates an external temperature sensor, placed in the floor during installation. It regulates the temperature of the floor, ensuring that the heat remains within a certain predefined range.
Domoteck ThermoLine produces a wide range of heating elements designed for problem solving and to prevent the accumulation of ice and snow on pavements, steps, paths and driveways, as well as in gutters and on roofs. The heating element is installed within concrete, stone or asphalt, or attached to the gutter or roof. These systems are the perfect safeguard against unpleasant accidents and the collapse of roofs. The cables can be used with or without an energy saving control unit. All heating elements provide the highest possible level of protection and safety.
Domoteck ThermoLine designs appliances purely for your comfort and enjoyment. All DTL appliances are energy efficient, safe, durable and of a superior quality. Domoteck ThermoLine appliances are practical and functional additions to both working and home environments.
Domoteck ThermoLine bath comfort products are designed to make your bathroom a more pleasant and calm place. With our smart technology we put focus on a safer and easier way for you to enjoy a comfortable time in your bathroom.
(3-13)
(14-17)
(18-20)
(21-27)
(28-31)
2
Pictures are for illustration only
TF-N CLASSIC MAT
STICKY MAT
PVC JacketingResistance
Wires
FEPInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
1
Domoteck ThermoLine TF-N Classic Mat is designed with a double insulated cable and sheathed to activate the RDC/GFCI.
Woven into a textile mesh which will best absorb the tile glue or self leveling concrete.
The TF-N Classic Mat’s heating element is produced in 50cm standard width, ideal for medium and large areas.
Even floor temperatures due tocable spacing (6.25mm)
Extra safe-reinforced insulation
No air pockets - due to textile mesh
Recommended for under:Tiles and natural stone.
FWM
2 S
1‐2
01
Output Mat
Output Cable
Voltage
Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
160W/m2
10W/lm
6.25 cm
0.5 m
~230V
PVC
~3.5mm
I+30mA RCD
One side Twin conductor
4.0m
TECHNICAL DATA:
Textile - Red. Cable - White
Floor Warming & Heating
Wire Spacing
The smaller the distance betweenthe heating wires, the more homogenous
the heat transfer.
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
3
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
3. Place the mat over the floor. 4. Press down the mat tothe floor.
5. Spread a layer of tile glue Pour self-leveling concrete.OR
6.Place floor covering e.g. tiles. 7. Set the thermostat.
25.5c10 4
OPTIONALINSUTECK - layer (see page 11) under warming mat.
Thermostat installedon inside room wall
Conduit
Thermostat installedon outside bathroom wall
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In 5 mm tile glue
Thermostat installedon inside room wall
Conduit
Junction box
Sensor
Construction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Warming mat overinsulation under tile glue
INSUTECKreinforced with tile glue
Call Today: +972 4-987-2266
Pictures are for illustration only
Floor
Construction
Insulation of the building
Sub-floor
Mat
Tile Glue
Tile Glue
4
5
Narrow cable spacing (5cm) allows for even floor temperatures
Ultra thin (only 3.5mm thick) and reinforced (double) insulated heating cable for higher safety and durability
Textile net allows for flexibility and absorption of tile glue
Pictures are for illustration only
Recommended for under:Tiles and natural stone.
TF-N COMFORT MATRecommended for under:Tiles and natural stone.
0.3m or 0.5m heating mat specially designed for small & large areas.
XLPE JacketingResistance
Wires
FEPInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
1
FWM
2 S
1‐2
05
FWM
2 S
1‐2
05
Output Mat
Output Cable
Voltage
Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
120W/m2 160W/m2
6W/lm 8W/lm
Textile - Red. Cable - Transparent
5 cm
0.5 m 0.3 m
~230V
XLPE
~3.5mm
I+30mA RCD
One side-Twin conductor
4.0m
TECHNICAL DATA:
Output Mat
Output Cable
Voltage
Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
200W/m2
10W/lm
Textile - Red. Cable - Transparent
5 cm
0.3 m
~230V
XLPE
~3.5mm
I+30mA RCD
One side-Twin conductor
4.0m
TECHNICAL DATA:
TF-N TURBO MAT
0.3 m and 200W/m2 heating mat specially designed for fast heat in small areas.
Floor Warming & Heating
STICKY MAT
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
6
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
3. Place the mat over the floor. 4. Press down the mat tothe floor.
5. Spread a layer of tile glue Pour self-leveling concrete.OR
6.Place floor covering e.g. tiles. 7. Set the thermostat.
25.5c10 4
Thermostat installedon outside bathroom wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In 5 mm tile glue
Floor
Construction
Insulation of the building
Sub-floor
Mat
Tile Glue
Tile Glue
Pictures are for illustration only
Call Today: +972 4-987-2266
7
Floor
Construction
Sub-floor
Mat
CCPE Insulation
FW
M 2
S 1
‐536
Call Today: +972-4-987-2266
ALUMINIUM MAT
ResistanceWires
FEPInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
The Aluminum Mat cable is screened, meaning the electrical wire is doubly insulated to withstand 4,000V. In addition, the copper wires are wrapped around a double insulated heating wire, which becomes a sensor, activating the RCD/GFCI in case of mechanical or thermal malfunctions.
The aluminum foil allows an even heat distribution across the entire floor.
The Aluminum Mat is designed for a dry, no-fuss installation under wooden flooring, and can also be installed over most existing hard floor surfaces such as tiles.
Extra safe due to screened cable
Perfect heat transfer due to aluminum foil
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’s testing instruments.
3. Roll out the CCPE
4. Roll the aluminium mat over the CCPE.
7. Set the thermostat.
25.5c10 4
5. Frame the aluminium mat with a blind net.
6. Place floor covering overthe mat.
Output Mat
Output Cable
Voltage
JacketingThickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
100W/m2 150W/m2
5.0W/lm 7.5W/lm
Silver
5 cm
0.5 m
~230V
Screened
~2mm
I+30mA RCD + aluminum foil
One side-Twin conductor
4.0m
TECHNICAL DATA:
Recommended for under: Laminates & Parquet (better is a 7-10mm thick laminate).
CCPE supplyment options:
Rolls of 1x10m
Tiles 0.5x0.5 6 units 1.5m2
For leveling the installation Domoteck can also supply blind net in rolls of 0.50M x 10M 5m2
Thermostat installedon inside room wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Parquet or laminate
Mat installed on4mm CCPE foam
Pictures are for illustration onlyFloor Warming & Heating
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
8
Floor
Construction
Insulation of the building
Sub-floor
Mat
Tile Glue
Tile Glue
Floor Warming & Heating
UNDERFLOOR BASIC FG
Underfloor Basic FG is suitable for both renovation and new construction projects.
Underfloor Basic FG is available in output:- 150W for standard rooms.
An ideal simple solution for floor heating, all-round application for kitchen and bathroom as well as in 10-25 mm self aligned concrete for engineered wooden floor.
Optimal combination of quality and low cost, due to fiberglass mesh
Output Mat
Output Cable
Voltage
JacketingThickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
160W/m2
11.85W/lm
Fiberglas - Red. Cable - White
7.4 cm
0.5 m
~230V
PVC
~4.0mm
I+30mA RCD
One side-Twin conductor
4.0m
TECHNICAL DATA:
Recommended for under: Tiles and natural stone.
PVC JacketingResistance
Wires
XLPEInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
1
Thermostat installedon inside room wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In 5 mm tile glue
FW
M 2
S 1
‐538
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’s testing instruments.
7. Set the thermostat.
25.5c10 4
6. Place floor covering e.g. tiles.
5. Spread second layer of tile glue
Pour self-leveling concrete.OR
3. Spread first layer oftile glue.
4. Using a roller press downthe mat.
Call Today: +972 4-987-2266
9
Thermostat installedon inside room wall
Conduit
Thermostat installedon outside bathroom wall
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In 5 mm tile glue
Floor
Construction
Insulation of the building
Sub-floor
Mat
Tile Glue
Tile Glue
Floor Warming & Heating
CLASSIC MAT
The Classic Mat’s heating element is produced in 50cm standard width, ideal for medium and large areas.
Even floor temperatures due tocable spacing (6.25mm)
No air pockets - due to textile mesh
Recommended for under: Tiles and natural stone.
PVC JacketingResistance
Wires
XLPEInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
1
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’s testing instruments.
5. Spread second layer of tile glue
Pour self-leveling concrete.OR
3. Spread first layer oftile glue.
4. Using a roller press downthe mat.
7. Set the thermostat.
25.5c10 4
6. Place floor covering e.g. tiles.
Output Mat
Output Cable
Voltage Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
160W/m2
10W/lm
6.25 cm
0.5 m
~230V
PVC
~4.0mm
I+30mA RCD
One side Twin conductor
4.0m
TECHNICAL DATA:
Textile - White. Cable - Red
FW
M 2
S 1
‐803
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
10
Thermostat installedon inside room wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In 5 mm tile glue
Floor
Construction
Insulation of the building
Sub-floor
Mat
Tile Glue
Tile Glue
Floor Warming & Heating F
WM
2 S
1‐8
22
TF-S COMFORT MAT
0.5 m width with XLPE jacketing designed for dry and large rooms.
Extra safe-reinforced insulation
No air pockets - due to textile mesh
Recommended for under: Tiles and natural stone.
XLPE JacketingResistance
Wires
XLPEInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
1
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’s testing instruments.
5. Spread second layer of tile glue
Pour self-leveling concrete.OR
3. Spread first layer oftile glue.
4. Using a roller press downthe mat.
7. Set the thermostat.
25.5c10 4
6. Place floor covering e.g. tiles.
Output Mat
Output Cable
Voltage Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
150W/m2
11.11W/lm
7.4 cm
0.5 m
~230V
XLPE
~3.5mm
I+30mA RCD
One side Twin conductor
4.0m
TECHNICAL DATA:
Textile - White. Cable - Red
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
11
Pictures are for illustration only
DOMOTHERM MR MAT
Heat distribution stripResistance
Wires Adhesive
tape
FEPInsulation
Super strongaramid
ShieldedGrounding
ReinforcedInsulation
The Domotherm Mat is manufactured with a screened heating cable which is integrated within a wide thin heating distribution strip. This process offers great advantages such as:· Larger percentage of heat transfer over the floor · Short setup & response times· Desired temperatures reached quickly & efficiently · Safe from electrical shock hazards
Its flat structure (2mm) minimizes floor elevation and ensures a more uniform distribution of heat.
The Domotherm Mat can be easily applied to existing floors, ideal for renovations.
Domotherm Mats can be installed under many kind of flooring:
Recommended for under:Tiles and natural stone,laminate and parquet, carpet.
FWM
1 S
1-9
70
Output Mat
Output Cable
Voltage
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
120W/m2 150W/m2
7.5W/lm 9.4W/lm
6.25 cm (40% coverage)
0.5 m / 1.0 m
~230V
~2.0mm
Ribbon width 25 mm
I+30mA RCD
One side - Single conductor
3 x 3 m
TECHNICAL DATA:
Fiberglass - Orange.
Floor Warming & HeatingTherm
oD
omoTeck
Flo
or W
arm
ing
& H
ea
ting
Line
An ideal solution for the whole house
Ultra thin cable (2mm)
Energy efficient
Easy to install
Tiles, Marble flooring (wet installation)
Carpet(dry installation)
Existing tile flooring(wet installation)
Laminated wooden floors (dry installation)
Call Today: +972 4-987-2266 12
Pictures are for illustration only
WET INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
4. Lay the mat and Spreadsecond layer of tile glue
5. Place floor covering e.g. tiles.Pour self-leveling concrete.OR
3. Spread first layer oftile glue.
Thermostat installedon inside room wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In tile glue
Thermostat installedon inside room wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Parquet or laminate
Mat installed on4mm CCPE foam
DRY INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
3. Roll out the CCPE insulation.
4. Roll the mat over the CCPE insulation.
6. Place floor covering over the mat.
5. Frame the mat mat with ablind net.
After 30 minutes heating
After 15 minutes heating
After 5 minutes heating
TEST: LAB TEMP 20O
C
Under TilesAfter 5 minutes heating
After 30 minutes heating
After 15 minutes heating
After 5 minutes heating
Under Carpet
After 5 minutes heating
After 5 minutes heating
After 30 minutes heating
After 15 minutes heatingUnder Laminate
13
Floor Warming & Heating
The INSUTECKcombined
with the tile glue
INSUTECKFloor warming insulation
The INSUTECK – A 10 mm thick slotted foam will provide insulation for energy saving and at the same time be a basic underlay for tiles.
The INSUTECK is laid out on a tile glue layer. The tile glue penetrates through the slots of the insulation foam and when the glue hardens, a hard insulation layer is created, allowing direct installation straight on it.
Installation with The INSUTECK allows uncoupling due to its partly soft and partly rigid properties.
Improves the efficiency of the underfloor heating system
Also functions as anuncoupling layer
Thickness
Width
Length
Weight
Thermal stability 4h at 80°C
Density
Water absorption
10 mm ± 10 %Thermal conductivity at 40°C 0.4w/mK
1000 mm ± 30 mm /500X500 mm
750g/m² ± 15%
20 m - 50 m
<2.0%
70kg/m³ ± 10kg/m³
Closed cell
TECHNICAL DATA:
4403
46
1. Tile glue spreading. 2. INSUTECK laying. 3. INSUTECK pressing. 4. Tile glue penetrating.
Flooring
Tile glue
Heating mat
INSUTECKconsolidated with the tile glue
Sub-floor
The tile glue penetrating the INSUTECK
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
14
XLPE JacketingResistance
Wires
FEPInsulation
Super strongaramid
BraidedGrounding
ReinforcedInsulation
1
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
5. Spread second layer of tile glue
Pour self-leveling concrete.OR
3. Spread first layer oftile glue.
4. Using a roller press downthe mat.
Mat width: 0.30 m X Mat length: 3 m / 4 m / 5 m
Comfort Wellness Mat is assembled as an IVC ("Invisible connection") enabling the element to be 100% water proof, providing an optimal level of safety particularly in wet locations.
Comfort Wellness Mat supply leads are exiting from the same place allowing an easier connection to the electrical wiring system of the building.
Bath Comfort
High level of safety due to IVC (invisible connection) designed for bathroom and wet areas
COMFORTWELLNESS MAT
FWM
1 B
1 - 8
30
FWM
1 B
1 - 5
52
Thermostat installedon outside bathroom wall
Conduit
Junction box
SensorConstruction
Insulation of the building
Sub- floor
Flooring Tiles or Natural Stone
Mat embedded In 5 mm tile glue
Pictures are for illustration only
Under the shower cubicle
Around the toilet
Output Mat
Output Cable
Voltage
Jacketing
Thickness of mat/wire
Protection class/means
Connection
Cable color
Space between heating wires
Supply lead length
200W/m2
9 W/lm
Red
4.5 cm
~230V
XLPE
~3 mm
I+30mA RCD
Two side-IVC-Single conductor
2 x 3.0 m
TECHNICAL DATA:
Mat size: 0.80 m X 0.80 m
Shower Wellness Mat (shower cubicle form mat) - is an underfloor warming element specifically designed for the shower cubicle, created to make your shower experience complete. Its design also allows for easy installation around the toilet.
SHOWERWELLNESS MAT
Designed for easy installation in the shower cubicle and around toilets
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
IVC CONNECTION -The connection between the supply leads and the heating element is internal and located under the jacketing, what makes the cable ultra safe and allow the cold lead and the warm cable to be at the same thickness.
Bath Comfort
Width Length W/unit Volts45 cm 50 cm 50 W ~230 V60 cm 75 cm 110 W ~230 V
TECHNICAL DATA:
FOG FREE MIRROR MAT
Prevents the mirror steaming up your viewA fog free mirror—a must in every bathroom!Easy to install
Domoteck ThermoLine Fog Free Mirror is suitable for the home, hotels, guest houses, etc.
This demisting unit is suitable with most types of mirrors, existing or newly installed.
Automatically activated when the room light is switched on.
Due to its flat design does not take up space.
Resistant to moisture, dust and aging.
Domoteck ThermoLine Fog Free Mirror should be installed in accordance with international regulations and standards.
AP
603
Pictures are for illustration only
Power Source
INSTALLATION
1. Take the product out of the box.
2. Mark the installation placeof the mirror and the
fog free mat on the wall.
3. Stick the fog free mat tothe wall in the marked place
using the included glue stripes.
4. Place the mirror 5 mm farfrom the wall using spacers.
5. Connect the fog free mat cable to the power source.
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-226615
Shelf Clasps
Glass Shelf
INSTALLATION
Install the product on the wall using screws as shown.
Install the shelf over the towel dryer using the clasps as shown.
Only for Diagonal Towel Dryer
Bath Comfort
Width Length W/unit Volts56 cm 66 cm 100 W ~230 V
TECHNICAL DATA:
Width Length W/unit Volts60 cm 70 cm 98 W ~230 V
TECHNICAL DATA:
DIAGONAL TOWEL DRYERLARGE TOWEL DRYEREquipped with a practical glass shelf for your accessories.
Energy efficient, dries towels rapidly.Provides the comfort of a warm & drytowel whenever required.
Practical & efficient for a single largetowel or multiple hand towels.
Can help to dry towels prior to throwing them into a hamper, which prevents mold and mildew from forming.
Domoteck ThermoLine Towel Dryers are quality stainless steel wall‐mounted bathroom towel dryers, suitable for the home, hotels, guest houses, etc.
Thanks to its special design the dryer can easily accommodate two bath towels without them overlapping.
Can be connected to the same thermostat that controls all the electrical components in the bathroom including an under floor heating system.
Domoteck ThermoLine Towel Dryers are energy efficient, dry wet towels rapidly and warm them before your shower or bath.
AP
667
AP
604
Screw
Covering Cap
Outside ClipInside Clip
Pipe Pipe
Pictures are for illustration onlyTherm
oD
omoTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266 16
17
Width Length W/unit Volts50 cm 80 cm 300 W ~230 V
TECHNICAL DATA:
RHP
310
Bath Comfort
CLASSIC TOWEL DRYER
Energy efficient ‐ dries towels rapidly.
Provides the comfort of a warm & drytowel whenever required.
Prevents damp towels from becomingmusty.
Can warm up baby blanketsor quilts on cold nights.
Towel warmers radiate heat, so theycan also act as room heaters in smallbathrooms.
The Classic Towel Dryer is a quality stainless steel wall‐mounted bathroom towel dryer, suitable for home, hotels, guest houses, etc.
Thanks to its special design it can easily accommodate two bath towels without them overlapping.
The Classic Towel Dryer can be connected to the same thermostat that controls all the electrical components in the bathroom including an under floor heating system.
The Classic Towel Dryer is energy efficient, dries wet towels rapidly and warms them before your shower or bath.
Optional design
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
Indoor Comfort
Width Length W/unit Volts50 cm 70 cm 65 W ~230 V60 cm 90 cm 95 W ~230 V
TECHNICAL DATA:
HEATING CARPET
Quick and easy solution for those extra cold days at home or at the office
Just place and plug‐in,no installation
Provides a simple solution for cold feet in the office, an ideal source of warmth and comfort on those extra cold days.
Domoteck Thermoline Heating Carpet is not only practical, it is also energy efficient & safe.
Place on the floor (not wooden) just plug in and immediately feel the pleasant warmth under your feet.
Domoteck Thermoline Heating Carpet complies with both national and international safety standards.
Domoteck Thermoline Heating Carpet provides a perfect warming solution, since the alternative would be to use a small electrical heater which is not only costly, but poses a fire hazard and last but not least unhealthy for the legs (varicose veins).
AP
602
Pictures are for illustration only
18
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
19
Indoor Comfort
Width Length W/unit Volts55 cm 55 cm 75 W ~230 V55 cm 75 cm 105 W ~230 V
TECHNICAL DATA:
PVC HEATING MAT
Quick and easy solution for thoseextra cold days
Just place and plug‐in,no installation
Energy efficient & safe
Domoteck ThermoLine PVC Mat is an electrically heated floor mat, practically designed to provide an ideal warming solution in cold working areas.
Especially practical for floors (not wooden) in working environments that are often dirty and wet, such as workshops,factories and service stations.
Domoteck Thermoline PVC Mat is not only practical and keeps your feet warm at all times, it is also energy efficient and safe.
Extra durable due to its heavy duty design. 4 holes in the corners of the mat, allowing to drill it to the floor.
Complies with national and international safety standards.
Domoteck ThermoLine PVC Mat provides a perfect warming solution, since the alternative would be to use a small electrical heater which is not only costly, but poses a fire hazard and last but not least unhealthy for the legs (varicose veins).
AP
607
Pictures are for illustration onlyTherm
oD
omoTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
20
Indoor Comfort
Width Length W/unit Volts35 cm 75 cm 65 W ~230 V
Gauged from25 cm height
EMF 65 W 0.75mg
TECHNICAL DATA:
PVC SHOE MAT
Quick easy solution for thosewet days
Just place and plug‐in,no installation
Domoteck ThermoLine PVC Shoe Mat is a new, practical, durable product, for every home especially with children around.
Provides an efficient solution for drying wet shoes.
Just plug in the mat at the beginning of the season and enjoy dry and warm shoes all winter long.
4 holes in the corners of the mat, which allows the mat to be screwed to the floor.
Complies with national and international safety standards.
AP
608
Pictures are for illustration onlyTherm
oD
omoTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
21
A sensible solution to avoid unpleasant accidents
Output Mat
Output Cable
Voltage
Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
300W/m²
30W/lm
Textile stripes. Cable - Red
10 cm
0.9 m
~400V
PVC
~6mm
I+30mA RCD
One side-Twin conductor
12m
TECHNICAL DATA:
ANTI-FROST TWIN MATRecommended for under:Concrete, stone or asphalt.
Should be installed during the construction of the pavement, driveway etc. Minimum installation temperature 5°C
Domoteck ThermoLine Anti-Frost Mat is the ideal heating element for outdoor snow melting & de-icing. Preventing the accumulation of ice on pavements, paths, driveways etc.
A perfect solution for avoiding unpleasant accidents, particularly for the elderly, disabled and children.
The Anti-Frost Mat is easy to install & maintenance free.
Domoteck ThermoLine Anti-Frost Mat can be regulated by a special de-icing control system, for convenience and energy saving.
Humidity SensorCU100-TE/HR
Double PVC Jacketing
ResistanceWires
FEPInsulation
Super strongaramid Braided
Grounding
ReinforcedInsulation
1
Pictures are for illustration onlyA
FM 2
B 4
- 70
9Outdoor
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
22
1. Ground
2. Crushed stones and/or
insulation
3. De-icing system embedded
in concrete / sand
4. Humidity Sensor
5. Asphalt
1. Control System
2. Humidity Sensor
3. Pavement
4. Concrete / Asphalt
5. Heating Element
6. Sand
7. Soil
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
6. Test Resistance.4. Customize accordingly. 5. Place ground sensor.
3. Lay down the mat.
Pictures are for illustration only
Call Today: +972 4-987-2266
High level of safety due to IVC(invisible connection)
A sensible solution to avoidunpleasant accidents.
Output Mat
Output Cable
Voltage
Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
300W/m²
30W/lm
Textile stripes. Cable - Red
10 cm
0.5 m
~230V / ~400V
PVC
~5.6mm
I+30mA RCD
Two side–IVC-Single conductor
2 x 4m
TECHNICAL DATA:
ANTI-FROST IVC MATRecommended for under:Concrete, stone or asphalt. Domoteck ThermoLine Anti-Frost Mat is the
ideal heating element for outdoor snow melting & de-icing. Preventing the accumulation of ice on pavements, paths, driveways etc.
Assembled as an IVC ("Invisible connection")due to a smooth, sealed and protectiveconnection between the supply lead& heating wire, the element is 100%water proof allowing for an optimal levelof safety in wet locations.
The Anti-Frost Mat is easy to install & maintenance free.
Should be installed during the construction of the pavement, driveway etc. Minimum installation temperature 5°C
PVC JacketingResistance
Wires
FEPInsulation
Super strongaramid
BraidedGrounding
ReinforcedInsulation
Pictures are for illustration onlyA
FM 1
B 3
- 74
6Outdoor
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Domoteck ThermoLine Anti-Frost Mat can be regulated by a special de-icing control system, for convenience and energy saving.
Humidity SensorCU100-TE/HR
IVC CONNECTION -The connection between the supply leads and the heating element is internal and located under the jacketing, what makes the cable ultra safe and allow the cold lead and the warm cable to be at the same thickness.
23
24
1. Ground
2. Crushed stones and/or
insulation
3. De-icing system embedded
in concrete / sand
4. Humidity Sensor
5. Asphalt
1. Control System
2. Humidity Sensor
3. Pavement
4. Concrete / Asphalt
5. Heating Element
6. Sand
7. Soil
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
6. Test Resistance.4. Customize accordingly. 5. Place ground sensor.
3. Lay down the mat.
Pictures are for illustration only
Call Today: +972 4-987-2266
25
Output Mat
Output Cable
Voltage Jacketing
Thickness of mat/wire
Protection class/means
Connection
Mat color
Space between heating wires
Mat widthSupply lead length
300W/m²
30W/lm
Textile - White. Cable - Black
10 cm
0.3 m
~230V
PVC
~5.6mm
I+30mA RCD
One side-Twin conductor
7.5m
TECHNICAL DATA:
PVC Jacketing
ResistanceWires
FEPInsulation
Super strongaramid Braided
Grounding
ReinforcedInsulation
1
1. Control system2. Tiles/marble3. Tile glue4. Heating element5. Tile glue6. Construction
STAIRS ANTI-FROST MATRecommended for under: concrete or stone.
INSTALLATION
1. Plan the layout. 2. Attach one of Domoteck’stesting instruments.
5. Test Resistance.
3. Lay down the mat.
4. Customize accordingly. 6. Set the thermostat.
25.5c10 4
The thermostat should be connected through atwo pole switch
!
A sensible solution to avoid unpleasant accidents
Practical width of 25cm for stairs
Domoteck ThermoLine Stairs Anti-frost Mat is specially designed for outdoor snow melting & de-icing for steps/stairs.
A perfect solution for avoiding unpleasant accidents, particularly for the elderly, disabled and children.
For convenience & energy saving the Stairs Anti-frost Mat can be regulated by Domoteck ThermoLine anti-frost control unit.
Assembled with a twin conductor (a one point connection to the wiring system of the building).
The Anti-Frost Mat is easy to install & maintenance free.
Pictures are for illustration onlyA
FM 2
B 4
-804
OutdoorTherm
oD
omoTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
26
Output Cable Voltage
JacketingThickness of wire
Protection class/means
Connection
Cable color Supply lead length
18W/lm + 30W/lm
Black
~230V
Polyolefin~7mm
I+30mA RCD + EPB
One side-Twin conductor
4m
TECHNICAL DATA:
PolyolefinJacketing
ResistanceWires
ReinforcedInsulation
Super strongaramid
PVC
BraidedGroundingFEP
Insulation1
ShieldedGrounding
DE-ICING CABLE EPBRecommended for above: roofs and gutters.
Electrical connection
High level of safety due to EPB(Equal Potential Bonding)
Domoteck ThermoLine De-Icing Cable EPB is a perfect heating element for preventing a build-up of ice and snow in gutters and on roofs.
Constructed with an additional layer of braiding and insulation, enabling a direct connection to the EPB (Equal Potential Bonding) in the main electric box, allowing for the highest level of protection and safety possible.
Domoteck ThermoLine De-Icing Cable is fire retardant, UV protected and halogen free.
Assembled with a twin conductor, a one-point connection to the electrical wiring system of the building.
Pictures are for illustration onlyA
FC 2
B 4
-637
Outdoor
Domoteck ThermoLine Gutter De-icing Cable can also be regulated by a special de-icing control system, for convenience and energy saving.
Gutter SensorCU100-TE/HR
EPB
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
27
EPB CABLE
INSTALLATION
2. Attach one of Domoteck’stesting instruments.
3. Holding bracket to protectthe cable from damage.
1. Test Resistance.
5. Carrying wire to take theweight of the snow from
the de-icing cable.
4. Fixing clamp to securecable.
6. Support spring to securecable at the end of the
downspout.
8. Plastic angle to securesensor cable.
9. Anchor plate to securethe cable on the roof.
7. Support hook to stabilizethe carrying wire.
10. Set the thermostat.
25.5c10 4
The thermostat should be connected through atwo pole switch
!
Pictures are for illustration only
Call Today: +972 4-987-2266
28
THERMOSTAT CU-345 STT FF
Pictures are for illustration onlyControl Units
Programmable ThermostatCU-345 STT FF is a combination of a thermostat and a timer. The timer can be programmed to 3 active periods per 24 hours, each day of the week different hours per period. The temperature can be set at any time independently of the timer to the desired temperature.
The thermostat has a factory default setting for continuous operation 24/7 at 100% output.
Color: WhiteLarge LCD display with clockPermanent user setting retention during power lossOverride functionEquipped with floor sensorFits to a standard 55 junction boxPacked in a cardboard boxIncluding instruction manual
5℃( 41°F) to 35℃ ( 95°F) Room temp. setting range
5℃ ( 41°F) to 40℃ ( 113°F) Floor temp. control range
±0.5°C Accuracy
200-240VAC 50/60HZPower source
16 Amps Max switching current
3500 Watt Max load power (in 220V)
21 IP Code
86x86x16 Dimensions (mm)
100 kΩ Floor sensor resistance
3 m Floor sensor length
TECHNICAL DATA:
THERMOSTAT CU-518 S R
Analog ThermostatMin./max. temperature limitationA locking mechanism is positioned behind the dial to limit the temperature. By loosening the right screw (see figure below), the upper and lower limits of the scale range can be adjusted; the red ring indicates the maximum limitation and the green ring indicates the minimum limitation.
Color: WhiteEquipped with floor sensorManual settingSquare panelTemperature control dial2 poll switch 16 AmpWill fit to a standard 55 junction boxEasy to installIncludes instruction manual
TECHNICAL DATA:
10°C~50°C Temperature control range
±0.5°C Accuracy
190V~240V / 50-60HZ Power source
0°C~+50°C Working environment temp.
-10°C~+60°CStorage environment temp.
16Amps Max switching current
3500 Watt Max load power (in 220V)
21 IP Code
81.5X81.5X46.5 Dimensions (mm)
100 kΩ Floor sensor resistance
3 m Floor sensor length
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
29
CU / SWITCH - 879
The new way to optimize electrical floor warming or heating.• Easy to operate• Increased comfort• Energy Efficient• Safety Standards
CU/SWITCH provides "HEAT ON DEMAND".- When set to low level operation (25%/33%), a basictemperature will be accumulated in the floor, the floor temperature will reach approx. 21oC - 22oC.- Once the home owner plans to use theroom/bathroom he/she can switch to a higher level such as 100%. The room temperature will quickly be elevated to the expected room temperature. The max floor temperature is set to 30oC.
The CU / SWITCH is mainly used with floor heating systems or any system where heat can be accumulated.
Automatic 100% activating function - in the CU/SWITCH 978By activating this function the CU/SWITCH will activate automatically 100% operation at 04:00 AM.A second 100% activation can be set by adjusting the wanted time.
Color: Off-White
Midsize display
Backlit display
Equipped with floor sensor
Packed in a cardboard box
Included instruction manual
30°C
33% / 66% / 100% or25% / 50% / 75% / 100%
Output operation options
Heat limit
200-240VAC 50/60HZPower source
16 Amps Max switching current
3500 Watt Max load power (in 220V)
21 IP Code
80x80x16 (879) 86x86x16 (978)
Dimensions (mm)
100 kΩ Floor sensor resistance
3 m Floor sensor length
TECHNICAL DATA:
Pictures are for illustration only
CU / SWITCH - 978
Power 33%operation
66%operation
100%operation
Power 75%operation
100%operation
25%operation
50%operation
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
30
Pictures are for illustration only
ACCESSORIES
SENSOR PIPE 90° ANGLE
Protecting the sensor cable from excess moisture.
Protecting the sensor pipe from excess bending.
CONTROL UNIT SET
Available as a set including any thermostat or switch with a sensor cable, sensor tube and a 90° angle.
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
31
TI 611 MULTIMETER
Digital Multimeter, Multi functionalEasily identifies cable damages during installation
Pictures are for illustration only
TESTING EQUIPMENT
Color: Yellow with grey panelEspecially developed for the DTL product installer with DK‐LT function: Identifies damages during installationA useful instrument for all product installers Large LCD display ‐ backlit display Buzzer alarmPacked in a cardboard box with test wires Includes instruction manual
9V BatteryPower supply
200mA/250V Safety fuse
LCDDisplay type
61 x 35 mmDisplay size
1999 Max. display
± 0,5% (3 ½) DC basic precision
182x84x36
Dimensions (mm)
247g (incl. battery)Weight
TECHNICAL DATA:
TI 612 FAULT INDICATOR
Fault IndicatorEasily identifies cable damages during installation
Detects the following faults:• Hot wire discontinuity• Shortcut between hot wires and grounding• Shortcut between sensor and grounding
Color: BlackABS plastic housingDeveloped for DTL products and products with a sensor wire (patent no. DE 101 01 378 C2), for identification of even superficial damages in the outer insulation layer of the cable.Easy identification of damages via buzzer alarm Fast and easy connectionCompact designIncludes instruction manual
V1.5 x 2Battery
100 x 80 x 25mmDimensions (mm)
100gWeight
SPECIFICATIONS:
Thermo
Dom
oTeck
Flo
or W
arm
ing
& H
ea
ting
Line
Call Today: +972 4-987-2266
ThermoDomoTeck
F l o o r W a r m i n g & H e a t i n gLine
Pleasant Home
Happy family
Simple & Perfect
Copyright 2006-2015 © All rights reserved. www.decoragroup.com www.domoteck-thermoline.co.il & all related companies. The materials in this page, may not
be reproduced, photocopied, displayed, modified or distributed in any form whatsoever without the express prior written permission of the copyright holder.
www.domoteck-thermoline.com | [email protected] | +972 4 987-2266
ThermoDomoTeck
F l o o r W a r m i n g & H e a t i n gLine