Think
Allie
d for
Autom
ation
& Co
ntrol
APR15-A&C Snipe_Snipe 3/13/15 2:39 PM Page 1
August 2015www.designworldonline.com
INSIDE:
LINEAR MOTION: Dont rule out lead screws PAGE 62
DESIGN FOR INDUSTRY: How timing belt propels h hovercraft PAGE 26
DEAN KAMEN: on making the world a better place through engineering PAGE 80
How to keep machines and people
72
safe
Cover_DW_August 2015_FINAL VERSION.indd 1 8/10/15 12:27 PM
the #1 value in automationOrder Today, Ships Today!
* See our Web site for details and restrictions. Copyright 2014 AutomationDirect, Cumming, GA USA. All rights reserved. 1-800-633-0405
Research, price, buy at:www.automationdirect.com/viewmarq
Connect to PLCs or othercompatible master devices
The Viewmarq line offers:
One-, two-, and four-line displays
Viewing distances up to 400 feet and 140 degree viewing angle
(1) RS232, (1) RS485 and (1) Ethernet port standard on all models
NEMA 4 / NEMA 12 extruded aluminum housings suitable for harsh environments
Chain and wall/ceiling mount brackets included
Industrial LED message displays keep your plantpersonnel in the know
Wall mount bracketsfor easy mounting
Our low-priced ViewMarq LED message boards candisplay preformatted and real-time factory oor data messages sent by a PLC, PC, or other master device. The text message displays can be controlled by:
ASCII strings through the RS232 or RS485 port
Modbus RTU messsages through the RS232 or RS485 port
Modbus TCP messages through the Ethernet port
C-more Microtouch panels
C-moretouch panels
Also Available
Unit shown$916 .00(MD4-0412T)
12 characters/4 line
Now starting at:$435.00(MD4-0112T)
12 characters/1 line
Six models to choose from:
$435
NEW PRICES
$613
$916
$929
$1,551
$599
New, lower prices on LED message displays!
Use the FREE Viewmarq con guration software(online download) to con gure the display; create,preview and send messages from a PC; or create ASCIIstrings that can be transferred to PLC instructions tocontrol the Viewmarq.
1508-DesignWorld-Viewmarq-MAG.indd 1 7/7/2015 1:13:02 PM
Automation Direct 8-15.indd 1 8/4/15 2:09 PM
Altech 8-15 (new).indd 1 8/4/15 2:21 PM
Together a winning combination for todaysservomotor applications.
Our ServoClass couplings have been recently redesigned to enable your actuator to go even faster and achievethe positional accuracy that will take your designs to the next level. Our couplings will do all this with low bearing loads.
3 New sizes now available.
Now, size, select and see the right ServoClass coupling solution for your application with Zero-Max 3D CAD files.
Check our FAST deliveries.
www.zero-max.com 800.533.1731
2010 ZERO-MAX
Your ball screw Your servomotor
Our coupling
# Zero-Max_full_pgs_r10_Design World 2/12/10 4:02 PM Page 1
Zero Max ad 10-14.indd 2 8/4/15 2:22 PM
Reliable detection for your application.
High-quality sensors from a high-service distributor.
More Premium Brands. More Products in Stock. More Solutions for You.See it all at thinkallied.com/industrialautomation
Allied Electronics, Inc 2015. Allied Electronics and the Allied Electronics logo are trademarks of Allied Electronics, Inc. An Electrocomponents Company.
1.800.433.5700
1st Choice in
Automation and Control
JUNE15 A&C Sensors Ad (DW)_Design World 5/12/15 11:47 AM Page 1
Allied Electrical 7-15_Reliable detection.indd 3 8/4/15 2:23 PM
I n s i g h t s
4 DESIGN WORLD August 2015
When I sat down with Dean Kamen last December in his office, he talked about how our society makes heroes out of sports stars and celebritiesand those are the people our kids (and disadvantaged children in particular) look up to. His vision in creating FIRST was to take the old science fair idea and make it more exciting, like a sporting event or a rock concert. Get engineering-type mentors for kids, to help them build things and learn the value of teamwork. Visiting the FIRST Robotics Championships in St. Louis is like spending a couple of days in Kamens long desired STEM-centered universe. What FIRST has created over a couple of decades is pretty amazing. Held slightly ironically in the Edward James Domehome of the St. Louis Ramsits hard not to get more than a little excited as the announcer shouts 1...2...3...TESLA! Goooooooo!!!! and thousands of kids are cheering wildly. Its like a science fair gone wild, mixed with thousands of kids for whom geeky is coolmy kind of kids, for sure. Young women proudly wear Rosie the riveter shirts. Guys wander the concourse holding blow up aliens and displaying Terminator shirts. On the competition floor, Im more impressed. They all speak so well and seem grown up beyond their years. Rick Schlack, who works for Southco in Concordville, Pa., was volunteering because his son, Trevor, was in the competition. He said the experience has helped push Trevor toward a technical field of study. Its helpedhes going to be a physicist, and he knows he wants to go through a doctorate, so he sees whats going on here, and its definitely solidified that, Schlack said. Kobe Greer, a 9th grader from Toronto, said hed learned a lot. Its a great learning experience, its a great community, everyones really friendly, he said. So many teams have told us what not to do and what to doand the rules. Without [the other teams], wed have probably gotten disqualified. Lots of people are helping us out because were rookies and they made this real easy. I love it. Were going to come back next year, and were going to come back the following years after that. Manny Carbajal, in his final year of college studying Innovation & Design Engineering at
FIRST in person
Pa u l J. H e n e y - Ed i to r i a l D i re c to rp h e n e y@w tw h m e d i a .co m
Has your company gotten involved in FIRST?Comment on Pauls blog on
Pneumatic Tips, www.pneumatictips.com/blogOn Twitter @ DWEditor
Universidad Panamericana, was volunteering for a Mexico City school. I started when I was 13 years old ... it was great and I was inspired by everything my mentors did for me. When you see an adult, an engineer, an important person, it inspires you. My first mentor was a GM electrical engineer and he was inspiring for me because he was always there. Everything I needed, he would always help me, he said. I found Luke Gries as his team from Hauppauge, N.Y., was readying to pack up. Gries, a junior in high school, got involved when a few of his friends joined the team his freshman year. I came the first night and I remember seeing the rebound rumble robotand I was blown away by how cool it was. They were shooting all the baskets and it just made me want to join and build stuff, he said. I want to be a mechanical engineer. This changed my life. From freshman year to where I am now, it set me on a career path and helped me so muchI cant even express how much. Kayleigh Head, a 10th grader from Houston, Texas, and her all-female team, Iron Plaid, stood out in their white tops and plaid skirts. Their energy was infectious. I joined FIRST because of a summer programI discovered programming and I discovered a whole new world, Head said. STEM opens your eyes so much to the world around you and how it works, and I think about things in a totally different way now. And I think that what makes FIRST so cool, is that it brings STEM to high school students and you can experience this great world and it prepares you so well for when you leave school. Head said she wants to study to be a computer scientist or an engineer. I asked her what shed say to Kamen if she ran into him one day. I would thank him so much for establishing this program, because it has changed my life so much, and I know its impacted so many other people, she said. This program is the best thing that I think has ever happened to me. Read my latest Q&A with Dean from after the FIRST championships starting on page 80.
Insights 8-15_Vs3.MD.indd 4 8/4/15 2:26 PM
MADE IN USA
www.exair.com/58/440a.htm
$$$$$$
$$$$$
$$$
$$
$
$$$$
@EXAIR
line up of coolers that are prone to bad behavior
If you would like to discussan application, contact anApplication Engineer at:
Opening the panel door and aiming a fan at the circuit boards is a bad idea. It is an OSHA violation that presents a shock hazard to personnel The fan blows hot, humid, dirty air at the electronics The cooling e ect is minimal It is likely to fail again since the environment is still hot
ese coolers are prone to failure in dirty, industrial environments when dustand dirt clogs the fi lter. It takes almost a day to install Vibration from machinery causes refrigerant leaks and component failures Compressor life expectancy is typically 2.5 years of continuous operation It requires a oor drain for the condensation Average cost to replace a bad compressor is $750
e plastic box cooler from a competitor uses an inaccurate mechanical thermostat thats designed for liquids. is thermostat has a poor ability to react quickly to changes in air temperature. It costs up to 85% more to operate than EXAIRs ETC Cabinet Cooler System with the same SCFM rating and Btu/hr. output. Electronics can overheat before it turns on It runs far longer than necessary before shutting o Increased cycle time wastes compressed air
ese have serious limitations.On hot summer days when the temperatures of the room and inside of the enclosure are about equal, theres notenough diff erence for exchange. They fail when dust and dirt clogs the lter The cooling capacity is limited due to ambient conditions
EXAIR Cabinet Cooler SystemsEXAIR has a complete line of Cabinet Cooler Systems to dependably cool and purge your electrical enclosures. ey convert an ordinary supply of compressed air into clean, cold 20F air. ey mount in minutes through an ordinary electrical knockout and have no moving parts to wear out. e compressed air fi ltration that is provided keeps water, oil and other contaminants out of the enclosure.
There is no room air filter to clog An accurate electrical thermostat control minimizes compressed air use All Cabinet Coolers are UL Listed to US and Canadian safety standards They are the only compressed air powered coolers that are CE compliant
Manufacturing Intelligent Compressed Air Products Since 1983
11510 Goldcoast Drive Cincinnati, Ohio 45249-1621(800) 903-9247 fax: (513) 671-3363
E-mail: [email protected] www.exair.com
When hot weather causes the electronics inside a control cabinet to fail, there is a panic to get the machineryup and running again. ere are several cooling options out there and its important to know the facts.
How To Keep Your Electronics CoolHow To Keep Your Electronics CoolHow To Keep Your Electronics Cool
Reliable and maintenance free!
www.exair.com/58/44058a.htmwww.exair.com/58/44058a.htmWATCHTHE VIDEO!
www.exair.com/58/44058a.htm
Exair 8-15.indd 5 8/4/15 2:24 PM
Te s c h l e r o n To p i c
Theres been a lot of bile spilled in the
blogosphere recently about a group
of economists at the University of
California Berkeley and the University
of Chicago. The researchers studied
Michigan households participating in a
Dept. of Energy effort called WAP (Federal
Weatherization Assistance Program).
WAP gives out grants that let low-income
families install energy efficient furnaces,
windows, insulation and other measures
aimed at cutting expenses for heating,
cooling and electricity.
L e l a n d Te s c h le r - Exe c u t i ve Ed i to rlte s c h le r @w tw h m e d i a .co m
Zinger: Many energy efficiency measures arent economical
On Twitter @ DWLeeTeschler
6 DESIGN WORLD August 2015
The economists found that money spent on these measures did, indeed, reduce energy consumption. Problem was, investments in energy efficient technologies didnt pay for themselves. In economic terms, the investments have negative annual returns both privately and socially (meaning, when the monetized value of the green house gas savings are included), wrote the economists. Perhaps even more disappointing, the recipients of WAP money didnt seem to live more comfortably. The households increased their indoor temperatures by less than a single degree on average during the winter months. These revelations are not good news for those who sell pricey windows and weatherization measures. Predictably, they havent taken this news well. Some of the comments online come across as though the economists had claimed Santa Claus was really a vampire. Not surprisingly, internet kibitzers have suggested the study authors had a conservative political agenda. Thats an interesting claim; one of the authors is a senior fellow at the Brookings Institution, sometimes described in the media as a liberal-centrist think tank. And UC Berkeley, from which two of the authors hail, is not exactly a bastion of conservative thinking. Other pundants in the green building space claim the study was too small. One I read was indignant that the researchers studied only a little over 600 households. In the spirit of generating more heat than light, it never
seemed to have occurred to the writer that 600 might be a statistically significant number, given what the economists were trying to discern. But once you get past the invective and name calling, there are interesting truths illuminated by all the back-and-forth thats spilling out online. One is that the engineering models contractors use to predict the pay-back of their energy efficiency solutions arent particularly accurate. On this score, here is a typical comment: The NEAT (National Energy Audit Tool) used by the programs they (the researchers) studied regularly under-estimates the efficiency of existing heating equipment. In the original paper, they estimate that the error in the NEAT tool to be about 25% (sic), since it was predicting heating energy use that was 25% higher than actually measured in those homes. Consumers should be troubled that NEAT and similar programs are spewing overly rosy predictions; their models are key selling tools of contractors who peddle weatherization services. Worse, contractors have an incentive to shade the results of these energy audits toward fixes that entail spending significant sums of money. In contrast, the lesson from the economists is to stick with improvements that dont cost much. One commentor may have summed it up best: The study mirrors my personal experience. Two years ago, I hired a contractor to nail down every board, caulk every gap, apply three coats of paint and blow insulation in the attic. This improvement reduced my electricity usage by a third a third! Overall, the biggest savings and the most cost-effective savings have come from paint, caulk, insulation and LED lightbulbs. DW
Lee Teschler Column 8-15_Vs2.MD.indd 6 8/4/15 2:25 PM
Helical 8-15.indd 7 8/4/15 2:27 PM
Follow the whole team on twitter @DesignWorld
WTWH Media, LLC6555 Carnegie Ave., Suite 300, Cleveland, OH 44103
Ph: 888.543.2447 FAX: 888.543.2447
NEW MEDIA/WEB/
BUSINESS DEVELOPMENT
Web Development ManagerB. David [email protected]@wtwh_webdave
Web Development SpecialistPatrick [email protected]@amigo_patrick
Video ManagerJohn [email protected]@wtwh_jhansel
Video CoordinatorJoshua [email protected]@wtwh_josh
Video InternNeil [email protected]
EDITORIAL
Editorial DirectorPaul J. [email protected]@dw_editor
Managing Editor Leslie Langnau [email protected]@dw_3DPrinting
Executive EditorLeland [email protected]@dw_LeeTeschler
Senior EditorMiles [email protected]@dw_Motion
Senior EditorMary [email protected]@dw_marygannon
Senior EditorLisa [email protected]@dw_LisaEitel
Associate Editor Mike [email protected]@wtwh_Michael
Assistant Editor Michelle [email protected]@wtwh_Michelle
Director, Audience DevelopmentBruce [email protected]
WORLDA DESIGN WORLD RESOURCE
Business Development ManagerPatrick [email protected]@wtwhseopatrick
Online CoordinatorJennifer [email protected]@wtwh_jennifer
MARKETING
Marketing Team LeaderStacy [email protected]@wtwh_Stacy
Marketing CoordinatorCarli [email protected]@wtwh_Carli
Marketing and Events CoordinatorNicole [email protected]@wtwh_Nicole
Marketing and Events CoordinatorJen [email protected]@wtwh_jen
Content AssociateLexi [email protected]@medtech_lexi
Traffic ManagerMary [email protected]
GRAPHICS
Director, Creative ServicesMark [email protected]@wtwh_graphics
Visual Design Manager Matthew [email protected]@wtwh_designer
Graphic Designer/Production Coordinator Margaret [email protected]@wtwh_Meg
2014 Winner
Crains Cleveland Business Fast 50 2014
8 DESIGN WORLD August 2015
Graphic Design Intern Erin [email protected]
2011, 2012, 2013, 2014
Cut to Width Roll Slitting
Custom Lamination
Custom Sheeting
Custom Belting
Custom Shape Die Cutting
We dont just sell the high endmaterials your company needs,
we cut to order, so you are neverstuck with wasted material again
With a comprehensive selection of specialized materials such as Teflon, Kapton, Silicone, PEEK, Kevlar, FEP, and PTFE coated fabrics, if your appli-cation demands performance, we can
provide a solution.
800 461 4161
Staff page 8-15_Vs1.indd 8 8/4/15 3:43 PM
Graybar 7-15.indd 9 8/6/15 11:23 AM
HOW DO I KNOW IF IM TALKING TO AN ENGINEER OR A SALESMAN?
Ask Smalley. We have nothing against sales people. But when it comes to differentiating Inconel from Elgiloy or overcoming dimensional variations within a complex assembly, wouldnt you rather work with an engineer?
Our customers would. Thats why they collaborate directly with our world-class team of Smalley engineersexperienced professionals whose only focus is helping you specify or design the ideal wave spring, Spirolox retaining ring or constant section ring for your precision application.
Smalley wave springs reduce spring operating height by 50%, saving space and weight, tting tight radial and axial spaces. We offer more than 4,000 stock sizes in carbon and stainless steel.
Visit smalley.com for your no-chargetest samples.
THE ENGINEERS CHOICE
HOW DO I KNOWIF IM TALKING TO AN ENGINEER OR A SALESMAN?
Ask Smalley. We have nothing against sales people. But when it comes to differentiating Inconel from Elgiloy or overcoming dimensional variations within a complex assembly, wouldnt you rather work with an engineer?
Our customers would. Thats why they collaborate directly with our world-class team of Smalley engineersexperienced professionals whose only focus is helping you specify or design the ideal wave spring, Spirolox retaining ring or constant section ring for your precision application.
Smalley wave springs reduce spring operating height by 50%, saving space and weight, tting tight radial and axial spaces. We offer more than 4,000 stock sizes in carbon and stainless steel.
Visit smalley.com for your no-chargetest samples.
THE ENGINEERS CHOICE
38139_Smalley_BrandAd_DesignWorld.indd 1 6/11/15 9:51 AMSmalley 7-15_NEW AD.indd 10 8/4/15 2:28 PM
July 2015 DESIGN WORLD 1 1
l C o n t r i b u t o r s S p o t l i g h t
62Take care of your machines and people with safety switches
ANDREW WAUGHProduct Manager for Sensors and SafetyAutomationDirect
ROBERT LIPSETT
Site Leader and Engineering ManagerThompson Industries
Dont rule out leadscrews 72
Programmable Encoders: The Next Generation
JARROD ORSZULAKProduct ManagerPosital Fraba
August 2015 DESIGN WORLD 1 1
At POSITAL, Orszulak coordinates an international team that develops custom products. He is especially enthusiastic about
extending the uses for industrial motion and position sensors into new areas such as alternative energy and medical devices. Ever since I was introduced to the field of Human Factors I have found it fascinating, he said. Understanding how people interact and understand technology is critical if it is to improve their lives. He cites lost knowledge as one of the big issues engineers face today. Whether it is baby boomer peers retiring or millennials jumping from one job to the next, with each individual turnover, knowledge is lost, he explained. Furthermore, CRM and advanced documenting tools cant replace the wisdom and relationships previous employees had with other peers, customers and suppliers. Speaking of baby boomers, Lipsett said advances in engineering will have an effect on them the most. Smart homes will monitor medication, while Skype and Facetime will provide social interaction with family and friends, he elaborated. Physicians will have a better understanding of a patients health and be able to intervene earlier. This all adds up to boomers living in their homes longer with a higher quality of life.
fun factLipsett and his wife love the great outdoors, where they can often be found kayaking or hiking. As prevalent as technology is, it is important to have some time off the grid, he said.
From a young age, Lipsett has been interested in understanding how things worked, an interest that was fostered by his parents and resulted in him taking apart anything on which I could find a fastener or means to disassemble. Most items went back together, he quipped. An alumnus of UC San Diego (bachelor of science) and the University of Southern California (masters), Lipsett said he finds computers one of the most frustrating technologies, due to the short life span of hardware driven software. As an ME, my passion is designing hardware that is robust and performs the required task in excess of the required life. Lipsett, who has been in the linear motion industry for 20 years and holds multiple patents, including one for the new Glide Screw, said he often finds junior engineers excelling at analysis and modeling, but sometimes lack experience in manufacturing processes and an understanding of traditional design solutions. This can result in out of the box thinking leading to breakthroughs, he said, but often junior engineers struggle to reinvent the wheel.
fun factWhen Lipsetts had a stressful work week, he enjoys getting away to the mountains to go skiing, biking and swimming.
Waugh, who holds a B.S. in Mechanical Engineering from Penn State, could not live without his TV streaming box and digital antenna. Being a recent cable cutter, my family has access to more HDTV than before and at a quarter of the cost. Shout-out to Roku, Tablo, Netflix, SlingTV and MLBTV! Waugh has a lot of school pride, calling the engineering program superior, but wishes Penn State had put a larger emphasis on the importance of communication. The ability to explain and share ideas, concerns and concepts is imperative in all business, including engineering and manufacturing, he said. As someone who has 15 years of experience working with position and process sensors, Waugh would like to see the continuing evolution of smart manufacturing. Smart homes with refrigerators that order food themselves and thermostats that learn trends and self-adjustthese products will become the norm for new machines and facilities in manufacturing, he said. Then theres talk of Industry 4.0 where your sensors provide self-diagnostics and tell the ERP to order replacements; motors communicate and schedule maintenance needs. Industrial Control Self Awareness? It is exciting, yet scarySkynet!
my advice
Every job, every project, every day is a learning experience. You are either learning what works, or what doesnt work. Both provide an opportunity for you to grow if you pay attention.
56
Contributor Page 8-15_Vs2.MD.indd 11 8/6/15 4:39 PM
Relay or Transistor Outputs
10A contact relay output, 300mA per channel transistor output
Digital, Analog and High-speed Inputs
Eight built-in digital inputs of which two can be configured as 0-10VDC/4-20mA analog inputs
4 high-speed inputs (up to 10kHz)
RS232C and RS485 ports
Serial and PLC communication Driver to communicate with other PLCs
USB-A Port
For data logging, recipe data and performing program updates
Embedded USB Mini-B Port
3 Bezel Colors
Silver Light gray Dark gray
Screens
STN monochrome (740cd/m2) 65K TFT color (400cd/m2)
RJ45 Ethernet Port
Supports remote Ethernet communication and Modbus TCP Driver to communicate with other PLCs
Flexible and Stress-free Programming
5MB screen-editing memory Over 7,000 symbol factory images
800.262.4332
Analog Expansion Cartridges
Add up to two analog expansion cartridges for an additional four analog I/O
Analog Outputs
Two 0-10V DC/4-20mA analog outputs
High Environmental & Safety Ratings
IP66f (water and oil tight) NEMA 4X (indoor) and 13 Class I, Division 2 for hazardous locations
HMI + PLC in One
Extreme Operating Temperature
-20 C to 55 C
www.IDEC.com/usa
Smart Products... Simple Solutions
By combining PLC and HMI functions in one, the FT1A Touch makes it faster and easier to build smart machines. This integration reduces initial design and maintenance costs by eliminating extra components and duplicate programming. Just one HMI+PLC unit optimizes efficiency and productivity by providing the complete functionality of a separate PLC and HMI system.
For more details and to read our Tech Note, visit www.IDEC.com/Touch
The Most Efficient Automation Solution
IDEC spread 7-15.indd 12 8/4/15 2:30 PM
Relay or Transistor Outputs
10A contact relay output, 300mA per channel transistor output
Digital, Analog and High-speed Inputs
Eight built-in digital inputs of which two can be configured as 0-10VDC/4-20mA analog inputs
4 high-speed inputs (up to 10kHz)
RS232C and RS485 ports
Serial and PLC communication Driver to communicate with other PLCs
USB-A Port
For data logging, recipe data and performing program updates
Embedded USB Mini-B Port
3 Bezel Colors
Silver Light gray Dark gray
Screens
STN monochrome (740cd/m2) 65K TFT color (400cd/m2)
RJ45 Ethernet Port
Supports remote Ethernet communication and Modbus TCP Driver to communicate with other PLCs
Flexible and Stress-free Programming
5MB screen-editing memory Over 7,000 symbol factory images
800.262.4332
Analog Expansion Cartridges
Add up to two analog expansion cartridges for an additional four analog I/O
Analog Outputs
Two 0-10V DC/4-20mA analog outputs
High Environmental & Safety Ratings
IP66f (water and oil tight) NEMA 4X (indoor) and 13 Class I, Division 2 for hazardous locations
HMI + PLC in One
Extreme Operating Temperature
-20 C to 55 C
www.IDEC.com/usa
Smart Products... Simple Solutions
By combining PLC and HMI functions in one, the FT1A Touch makes it faster and easier to build smart machines. This integration reduces initial design and maintenance costs by eliminating extra components and duplicate programming. Just one HMI+PLC unit optimizes efficiency and productivity by providing the complete functionality of a separate PLC and HMI system.
For more details and to read our Tech Note, visit www.IDEC.com/Touch
The Most Efficient Automation Solution
IDEC spread 7-15.indd 13 8/4/15 2:30 PM
Co n te n t s | A u g u s t 2 0 1 5 v o l 1 0 n o 8 | d e s i g n w o r l d o n l i n e . c o m
1 4 DESIGN WORLD
MOTION CONTROL
Programmable encoders: The Next GenerationThe latest programmable encoders offer both incremental and absolute functionality on one hardware platform and can be programmed with a WiFi connection.
2014
3
2014
3
56
F E A T U R E S
72 MECHATRONICSTake care of your machines and people with safety switchesOperator safety is a top priority for machine and robot installations, and safety switches help to implement the desired level of protection.
Paper based 3D printingreduces surgical time
A supplement of Design World August 2015
Inside:
92
Expert viewpoint:
How additive
technology will affect
manufacturing
96
Additively manufacturing
a cranial implant
100
2014
3
LINEAR MOTION
Dont rule out lead screwsHere we explain where lead screws excel in linear-motion applications. Then we explain
how to apply them.
62
ON THE COVERSafety switches are not just designed to protect operators, but machines as well.
Photo: courtesy of AutomationDirect.
80 DEAN KAMENDean Kamen on making the world a better place through engineeringWhat makes a true engineering leader?
A Supplement to Design World
August 2015
Design mission ready devices and equipment faster, smarter, and under budget with TiPS from leading suppliers
Aerospace cover 2015_main issue_FINAL.indd 105 8/5/15 2:08 PM
PAGES 88 -103 PAGES 105 -123
CONTENTS AUGUST 2015_first page_Vs4.LL.MD(1).indd 14 8/7/15 9:34 AM
ODU-USA 8-15 (new).indd 15 8/5/15 4:07 PM
Co n te n t s
D E P A R T M E N T S
4 Insights
6 Teschler on Topic 11 Contributors 18 Green Engineering
22 Engineering Exchange
26 Design For Industry
34 Design Notes
42 CAE Solutions
48 Internet of Things
126 Product World
128 Ad Index
8. 2 0 1 5
1 6 DESIGN WORLD August 2015
34
48
42
May issue Market Trend article correction
Note that IndraDrive Mi electric drives are from Bosch Rexroth, and they integrate into machines to let designers build compact designs. The decentralized supply and mains modules also let machine builders integrate all drive components directly into the machine without a control cabinet. Ed.
26PiMotion BLDC, Stepper & Voice Coil Controller & Driver Linear Driver for Low Electrical Noise Dependable 100base-T Network Interface Multi Unit Synchronization over LAN Network Cross-Platform Support - LINUX, WIN, MAC Mobile Device Support - iOS & Android Multi Language Support - C/C++, Python, Java Secure Communication Enabled - AES 256www.vena.com
Contents AUGUST_second page_Vs1.indd 16 8/6/15 4:16 PM
Whatever keeps you up at night, weve got a solutionthe largest selection of motors, pumps and air-moving devices available. Plus, one-of-a-kind solutions ready to be
custom-engineered for your precision industrial, commercial, combustion or transportation application. If you can dream it, youll find it at Solution City.
FOR MOTION CONTROL INNOVATION, SOLUTION CITY NEVER SLEEPS.
2015 by AMETEK Inc. All rights reserved.
100 East Erie StreetKent, OH 44240ametekdfs.com
AMETEKPMC 18611_City Never Sleeps Ad_9x10.875.indd 1 7/29/15 9:14 AMAMETEK PMC (Solutions City) 8-15 (NEW).indd 17 8/4/15 2:32 PM
Reducing food processing plants energy costs
Food processors in the U.S. face an unprecedented competitive environment and must look for ways to be profitable without negatively affecting the quality
of finished products. The challenge of maintaining high product quality while
simultaneously reducing production costs can often be met through investments in
energy efficiency, which may include the purchase of energy-efficient technologies
like high-efficiency motor systems.
According to the Department of Energy (DOE), electric motor-driven systems
are estimated to consume more than half of all electricity in the U.S. and more
than 70% of all electricity in food and beverage manufacturing applications. These
processing plants are large users of energy for refrigeration, cooking, heating, boilers
and steam generation, sterilizing, conveyors and auxiliary equipment. However,
because energy is typically viewed as peripheral to the business of production,
efficiency projects have an uphill fight for capital and attention. Even if organizations
adopt a more holistic approach to energy, managers and engineers
often dont have the time to analyze payback from various
projects and prioritize them. But this should be one of the first
places to look for reducing costs and improving productivity and
profits.
The typical industrial plant in the U.S. can reduce its
electricity use by around 5 to 15% by improving the efficiency
of its motor-driven systems. Process manufacturing
has the highest absolute consumption of electricity,
419,587 GWh/year, and motor systems account for
71% of this total.
A significant challenge in promoting high-efficiency motors
is that motor buyers often misunderstand where the costs of
motor ownership lie, and therefore do not account for these
costs accurately. The greatest cost of motor ownership is that of
operating the motor, which represents 97 to 98% of lifetime costs.
Initial purchase price represents only an estimated 2 to 3%.
Electric motors used in production facilities with conveyors are
almost always on, driving the energy bill higher. But what if there was a
way to reduce energy consumption and costs while increasing the efficiency level?
There isthrough the use of high-efficient motors. Energy efficient motors make
economic sense: In an industrial application operating 4,000 hours/year, energy-
efficient motors earn back their initial cost in two years.
G r e e n E n g i n e e r i n g
1 8 DESIGN WORLD August 2015
Green Engineering_8-15_Vs2.MD.indd 18 8/4/15 4:03 PM
Dedicated to dierentiating our customers productsDunkermotor is a leading manufacturer of customized rotary and linear motion solutions providing low-risk product development, lower total system cost and faster time to market for original equipment manufacturers in the automation, medical, solar, packaging, semiconductor and transportation industry segments. 1500 Bishop Ct - Mt Prospect, IL 60056
Call: [email protected]
WHEN SPEED MATTERS THE MOST. And Aordability
More than 1,000 motion solutions to choose from, most with same-day shipping option. Design your own, today!
Brushed and Brushless DC motors Planetary and Worm gearboxes options Integral All-in-One BLDC Diameter from 30 to 75mm
Power from 10 to 450 Watts
Motor stall torque up to 400Ncm (580 oz.in)
Gearbox output torque up to 160Nm (120 ft.lb)
Nema 17, 23, 34 ange options
dunkermotor.com/express
Dunkermotor 8-15.indd 19 8/4/15 2:33 PM
G r e e n E n g i n e e r i n g
2 0 DESIGN WORLD August 2015
Many state organizations and energy companies have created
monetary rebate programs available to qualifying businesses. For
example, the Wisconsin Food Processing Plant and Food Warehouse
Investment Credit is a refundable tax credit for businesses that have
invested to modernize or expand food processing plants or food
warehouses in Wisconsin and who have been certified by the Wisconsin
Department of Commerce.
Tax credits are earned by incurring eligible expenses for
modernization or expansion of a food processing plant or food
warehouse. This includes constructing, improving or acquiring buildings
or facilities, or acquiring equipment for food processing or food
warehousing.
Wisconsin also has the Meat Processing Facility Investment Credit
program to support the modernization of the states meat processing
industry. The tax credits build on the success of the states dairy
modernization and investment tax programs. The program provides
a tax credit for up to 10% of the expenditures meat processors invest
in modernization or expansion. Eligible costs include construction,
additions, utility upgrades, equipment, technology and other upgrades.
In southern Indiana, Dubois REC and other local rural electric
cooperatives, in a partnership with Hoosier Energy, have created a
monetary rebate program for energy efficient upgrades. Local electric
cooperatives have been offering rebates on energy efficiency upgrades
through Hoosier Energy since 2009. DW
Submitted by Cheryl Higgins, product marketing manager,
LEESON Electric, www.leeson.com.
Green Engineering_8-15_Vs2.MD.indd 20 8/4/15 4:04 PM
www.catalystmotiongroup.com
A single resource for integrated mechanical, electronics, drives and software, with experienced customer support for the development
of simple-to-sophisticated automation systems.
At Catalyst Motion Group, we are able to congure motion systems by utilizing our own component level supply. What this means for our clients is full accountability for customized solutions while realizing the improved eciencies of a reduced supplier count and receiving fully tested and delivered solutions.We can provide you with the ultimate solution for almost any application, while managing scheduling demands, technical requirements and nancial considerations. We are able to accomplish this through coordinated utilization of our extensive engineering resources and vertically integrated manufacturing resources.We put it all together customized motion systems that include stepper motors, brush and brushless DC motors, linear mechanics, drives, electronics and an extensive array of peripheral system components. Our considerable and wide-ranging in-house manufacturing capabilities allow us full control of the entire process, from development of prototypes to delivery of fully tested production units. And, with our engineering capability, if we don't have it ...we can develop it! We have successfully developed and taken to production fully customized motion solutions for a wide variety of advanced technologies including: Medical devices for diagnostics, surgical procedures, therapeutics and pharmaceuticals Laboratory and analytical instrumentation and equipment Industrial automation including robotics and production line processing operations We are innovative, exible and most importantly a secure, reliable, and knowledgeable resource ready to respond to your most challenging motion control needs.
Your Catalyst to InnovativeMotion Control Solutions
1500 Meriden Road Waterbury, CT 06705 U.S.A. Call 1 203 725 3852
CATALYSTM O T I O N G R O U P
C
M
Y
CM
MY
CY
CMY
K
AMETEK Catalyst 8-15 (New).indd 21 8/4/15 2:34 PM
CONNECT with Design World
DIGITAL ISSUE
Visit designworld-digital.com for our latest issue!
FOLLOW US
Connect with 339,805 engineers at
facebook.com/DesignWorldNetwork.
Grow your network. Join the Design World
group on LinkedIn.
Hot products and topics are streaming at
youtube.com/Design-WorldVideo.
Hang out and track what's new at
plus.google.com/+DesignWorldOnline.
See shared slides atslideshare.net/
DesignWorldOnline.
Over 13,000 members - global educational engineering community - join today.
engineeringexchange.com.
Find meaningful links and tweet along with us
@DesignWorld.
Check the boards and see whats being pinned up at
pinterest.com/engineeringex.
Think
Allie
d for
Autom
ation
& Co
ntrol
APR15-A&C Snipe_Snipe 3/13/15 2:39 PM Page 1
August 2015www.designworldonline.com
INSIDE:
LINEAR MOTION: Dont rule out lead screws PAGE 62
DESIGN FOR INDUSTRY: How timing belt propels h overcraft PAGE 26
DEAN KAMEN: on making the world a better place through engineering PAGE 80
How to keep machines and people
72
safe
Does the hydraulic industry need to consider the preservation of laminar flow?Laminar flow describes the ease of flow, and it
describes how the desire of a fluid to travel is
parallel straight lines, whenever possible.
What's the difference between inertia and momentum? The concepts of inertia
and momentum are
often confusedpossibly
due to the similarity of
their definitions. Inertia
is generally described as
an objects resistance to
motion, with momentum being the tendency of an object
to continue moving. Both have implications for linear
motion applications, but while inertia is a fundamental sizing
parameter, momentum isnt directly addressed in system
calculations. To distinguish between the two and find out
why that is, well look at the definitions and uses of each.
Posted by Danielle Collins, Contributing Editor
ENGINEERING EXCHANGE
GOOGLE+
2 2 DESIGN WORLD
YOUTUBE
What is open architecture?
http://dwo.me/1O6COXZ
http://dwo.me/1O6EUY0
Senior Motion Control Editor Miles Budimir discusses the
variety of motion control networks such as Ethernet/IP and
Sercos as well as design considerations such as scan or
update rates.
http://dwo.me/1O6D74Y
The basics on mil spec connectors from ODU
http://dwo.me/1O6DAnV
http://dwo.me/1O6EKQd
Where is hydraulic bar stock used (besides in cylinder piston rods, of course)?
Engineering Exchange 8-15_Vs1.indd 22 8/7/15 9:49 AM
2015 by AMETEK Inc. All rights reserved.
Nothing moves air with more rock-solid reliability than AMETEK Rotron regenerative blowers. Fifteen years service life is not unusual. These low-pressure, high-volume blowers feature rugged, compact construction and quiet operation. Their proven design makes them ideal in applications from chemicals, wastewater and furnaces to vapor recovery and more. Plus, theyre backed by the industrys most knowledgeable engineering experts. AMETEK can customize your blower for harsh environments, high voltage and specialized applications, too. So make your next air-moving challenge a breeze. Call us at +1 330-673-3452 or visit our website to get started.
Whats 15 years to one of our blowers?A warm-up.
100 East Erie StreetKent, OH 44240ametekdfs.com
AMETEKDFS Regen Blower Ad_9x10.875.indd 1 6/1/15 5:03 PMAMETEK 6-15 (NEW AD).indd 23 8/4/15 2:35 PM
Austin
2 4 DESIGN WORLD August 2015 www.designworldonline.com
NI Week RecapLee Teschler
A bicycle built for noneA lot of interesting technology comes out of universities. In that regard, consider the driverless bicycle on display in the NI Week exhibit area. It was created by students at Tsinghua University in China and was partly sponsored by Baidu, the
Chinese search engine. Ph.D. student Sotiris Stasinopoulos did much of the work on the sensors, the path planning, obstacle detection and path optimization. He explained that a remote operator steers the bicycle using a remote control as might be used for an ordinary radio controlled plane. A GPS sensor and gyroscope reside in the rear of the bike, rather than near the center of gravity, as is normally the case for systems that balance mechanical structures. The reason is that a gyroscope sitting near the bike center doesnt generate enough of a torque signal to stabilize the bike. The rear-mounted gyro mainly senses the roll angle as the bike moves. A maxon motor moves the front fork through a 9:1 gearbox to keep the bike upright. The bike contains two other motors, one for locomotion, the other for braking. Sotiris said it took students about seven months to perfect the stabilization algorithm.
Paul J. Heney
This years NI Week continued to impress upon attendees that the Internet of Things (IoT) is cominglike a wave, like the Borgand resistance is futile. Engineers need to over-design their products for future flexibility and realize that there is a Cambrian explosion of data coming (as Eric Starkloff, EVP of global sales and marketing put it so well). That means not just more data, but more diversity in the types of data that we will have to deal with. The IoT is also helping to create technology in things like software and sensors, and the varied applications on hand here in Austin certainly proved that. Engineers were treated to real-world uses of NI products in airplane testing, remote surgery, agricultural equipment, wearable technology, smart bracelets, GoPro cameras, the electrical grid, driverless cars, next generation wheelchairs, and a lot more. The interconnected world is here, and its only getting more exciting.
2 0 1 5
NI Week 8-15_Vs3.LL.MD.indd 24 8/7/15 10:14 AM
Austin Steve Meyers
Firefly Equipment takes the world of agricultural machinery and makes it super high tech with the new ProSlab Harvester. It automatically cuts, removes and stacks pads of sod grass on wood pallets with incredible precision. The machine combines five axes of electric servo drives with multiple axes of hydraulic actuation, touch screen HMI and multiple networks to produce a smooth running system for growers that need to bring grass turf to the marketplace. The main controller is National Instruments Compact Rio with multiple networks to synchronize all the internal controls. In addition, it connects all the machine systems with remote cellular access, producing full monitoring and diagnostics.
Lisa Eitel
The 2015 NI Week showcases hundreds of cutting-edge applications5G networks, data super-positioned over live streams of real-world devices, smart-grid integrationand the daily keynotes continue to wow attendees. Behind these flashy scenes are also dozens of intensive training sessions for those just beginning to use NI software and hardware, as well as certification tracks for power users looking to further their LabVIEW programming and other design skills. According to NI, the sessions can help attendees cut coding time in half and spend 43% less time on code maintenance.
NI Week also serves as a meeting for academics to share their latest research findings and discuss the future of engineering. One unifying theme is how participating students and professors from around the world use LabVIEW in their work, including everything from simulated veterinary biomechanics to complex control of robotic semiconductor machinery.
One presentation particularly exciting for the motion-design world was from Daniel Mohsenizadeh, researcher at Center for Bioinformatics and Genomic Systems Engineering (CBGSE), Texas A&M University.In the presentation, Mohsenizadeh and others describe a new way to design PID controllers for linear controls based on frequency-response measurements. The technique requires no transfer function or state-space model, and can handle the design process directly from frequency-domain data. Attendees got to see how to use it for real-world applications and see the experimental PID controller work a servomechanism with NI and Quanser components.
August 2015 DESIGN WORLD 2 5
NI Week 8-15_Vs3.LL.MD.indd 25 8/6/15 12:48 PM
01
m i l i t a r y / a e r o s p a c e
D e s i g n f o r I n d u s t r y
2 6 DESIGN WORLD August 2015 www.designworldonline.com
m e d i c a l
Polycarbonate safetySeveral years ago, engineers were disuaded from using bisphenol A (BPA) as a material choice in many applications where people might use a product made from it. Heres an argument for revisiting the use of
this material.
The human body can survive for weeks without food. Without water, its only days. As such, access to clean, safe drinking water is absolutely vital. Perhaps at no time is this more evident than in the aftermath of natural disasters like floods, hurricanes and earthquakes. Disease can spread rapidly and people can quickly become dehydrated when the clean water infrastructure has been compromised or destroyed. In such situations, bottled water can mean the difference between life and death. Customers of 3- and 5-gal water bottles for home, office and retail delivery require a plastic that can meet market demand for sturdy, yet lightweight bottles that can be recycled. Bayer MaterialScience, a global polycarbonate supplier, offers a polycarbonate formulated to provide good flow, exemplary dimensional stability, high mechanical and impact strength, and excellent light transmission and transparency. Polycarbonate 3- and 5-gal water bottles can be washed and reused more than 50 times, one of the longest service lives of any water bottle in the field. Most importantly, the bottles, like all bottled water containers, are also sustainable. At the end of its life cycle, the polycarbonate can be recycled into near-virgin resin for second-life use in a variety of applications. Safe, reliable and rugged, polycarbonate is a proven packaging material. Still, one of its chief chemical building blocks, also known as a monomer, is BPA, and it is frequently misunderstood. The emotional controversy surrounding this monomer often means that reasonable, science-based questions that may be asked about any complex subject can quickly turn confusing. With that in mind, Bayer MaterialScience and the International Bottled Water Association (IBWA) have teamed up to encourage a fact-focused conversation about polycarbonate.
What is BPA? It is a chemical building block used primarily to make polycarbonate plastic and epoxy resins. Polycarbonate has been the material of choice for food and beverage product containers for nearly 60 years because it is lightweight, highly shatter-resistant and transparent. It is widely used in various food containers and many other everyday items, such
DFI 8-15_Vs6.LL.MD.indd 26 8/5/15 9:12 AM
August 2015 DESIGN WORLD 2 7
WHITTET-HIGGINS manufactures quality oriented, stocks abundantly and delivers quickly the best quality and largest array of adjustable, heavy thrust bearing, and torque load carrying retaining devices for bearing, power transmission and other industrial assemblies; and specialized tools for their careful assembly.
Visit our websitewhittet-higgins.comto peruse the many possibilities to improve your assemblies. Much technical detail delineated as well as 2D and 3D CAD models for engineering assistance. Call your local or a good distributor.
33 Higginson Avenue, Central Falls, Rhode Island 02863Telephone: (401) 728-0700 FAX: (401) 728-0703 E-mail: [email protected] Web: www.whittet-higgins.com
POWER TRANSMISSIONRETAINING DEVICES &maintenance & assembly tools
WHITTET-HIGGINS
USA
BEARLOK SHOELOK BEARLOK Shrink Disc
BEARHUG CLAMPNUT TANGENTLOK
PRECISION NUTS & WASHERS ADAPTER SLEEVE ASSEMBLIES
NUTS & WASHERS HARDENED TONGUE WASHERS SPLIT COLLAR
RETHREADING DIES ADJUSTABLE SPANNER WRENCH BEARING ASSEMBLY SOCKET
INCH and METRIC THREADSLEFT HANDED as well as
RIGHT -HANDED
Materials of:CARBON, ALLOY and HARDENED ALLOY
STEELS
Materials of:ALLUMINUM and
CORROSION RESISTANT STEEL
D e s i g n f o r I n d u s t r y
as eyeglasses and compact discs. For example, many bottled water companies use polycarbonate plastic for their 3- and 5-gal water cooler bottles. Because of less stringent toughness requirements in single-serve water bottle containers, polycarbonate is not used there. Science and experts agree: BPA is safe for its intended uses. Key government bodies around the world have issued favorable opinions on the safety of this monomer. The consensus among these international regulatory agencies, which include the U.S. FDA, Health Canada, the Japanese National Institute of Advanced Industrial Science and Technology, World Health Organization/FAO (Food and Agriculture Organization of the United Nations), and the European Food Safety Agency (EFSA), is that BPA is safe when used as intended. Many international studies have been conducted to assess the potential for trace levels of monomer to migrate from lined cans or polycarbonate bottles into foods or beverages. The conclusions from those studies and comprehensive safety evaluations by government bodies worldwide are that polycarbonate plastic water bottles are safe for consumer use. On Jan. 21, 2015, EFSA announced the findings of a comprehensive re-evaluation of BPA exposure and toxicity, concluding that dietary exposure to BPA poses no health concern to consumers of any age group, including unborn children, infants and adolescents. In addition, EFSA noted that exposure to BPA from the diet or from a combination of sources (such as diet, dust, cosmetics and thermal paper) is below the safe tolerable daily intake (TDI) level. On Jan. 6, 2015, the U.S. FDA updated its Bisphenol A (BPA): Use in Food Contact Application page on its website. The update references the newest FDA safety assessment of BPA for use in food contact applications conducted in 2014. The webpage states that, FDAs current perspective, based on its most recent safety assessment, is that BPA is safe at the current levels occurring in foods. Based on FDAs ongoing safety review of scientific evidence, the available information continues to support the safety of BPA for the currently approved uses in food containers and packaging. The fact is that international, independent and objective scientific research has repeatedly shown BPA, when used as a monomer for plastics in food contact applications, to be safe. The Bayer polycarbonate, Makrolon WB1239, used in water bottle applications, is approved by the U.S. FDA for use in water bottles, as well as other food contact applications. A variety of other grades of polycarbonate can be used in food-contact applications as well. DW
Bayer Material Sciencematerialscience.bayer
DFI 8-15_Vs6.LL.MD.indd 27 8/5/15 9:13 AM
Whether a conveyor moves small or large parts, efficient and quiet operation are
frequent requirements. For small part material
handling applications, the 1100 Series conveyor
platform now comes with upgraded fixed speed motors
that are 50% quieter than the previous version, and still rated
2 8 DESIGN WORLD August 2015 www.designworldonline.com
02 D e s i g n f o r I n d u s t r y m a t e r i a l h a n d l i n gMotors improve belted conveyor efficiency
P114
1-800-933-4915 www.trimlok.com
C
M
Y
CM
MY
CY
CMY
K
P114 8.5 x 4.75 HORIZONTAL TL ad.pdf 1 4/18/14 8:00 AM
DFI 8-15_Vs6.LL.MD.indd 28 8/5/15 9:44 AM
August 2015 DESIGN WORLD 2 9
for 10,000 hours of operation. The motor
is dimensionally identical to the pervious
versions. The 1100 Series conveyor has a frame height of in. This low profile enables the conveyor to fit into tight spaces. It is suitable for applications requiring lightweight or small product movement and is Clean Room Class 100 Certified. The belt conveyor has a 58-in. roller transfer tail for accurate and efficient small-part end transfers; the conveyor belt is nearly flush with the frame for easy side transfers; and the patent-pending pinch drive allows for 15-lb load without the need for high belt tension.
WHAT DO YOU THINK?
Connect and discuss this and other design engineering issues with
thousands of professionals online
BOKERS.COM/DW
FREE CATALOG & BROCHURE
Call (888)-WASHERS(888)-927-4377 612-729-9365
WASHERS & STAMPINGS
m a t e r i a l h a n d l i n g
A global educational
engineering network,
Connect, share and
learn today.
www.engineeringexchange.com
A global educational
engineering network,
Connect, share and
learn today.
www.engineeringexchange.com
Connect with 339,805 engineers at
facebook.com/DesignWorldNetwork.
Grow your network. Join the Design World group
on LinkedIn.
Hot products and topics are streaming at youtube.com/Design-
WorldVideo.
Hang out and track what's new at
plus.google.com/+DesignWorldOnline.
See shared slides atslideshare.net/
DesignWorldOnline.
Over 13,000 members - global educational engineering community - join today.
engineeringexchange.com.
Find meaningful links and tweet along with us @DesignWorld.
Check the boards and see whats being pinned up at
pinterest.com/engineeringex.
A variable speed motor is also available. The fixed speed may have an on/off switch on the motor. The variable motor may have several control options including 24 Vdc or 115 Vac input power options. Additionally, users can interact with the variable speed motor from either the control panel, or it can be wired to be controlled remotely. DW
Dorner Conveyorsdornerconveyors.com
DFI 8-15_Vs6.LL.MD.indd 29 8/5/15 9:46 AM
Longest endless timing belts help propel hovercraft
03 D e s i g n f o r I n d u s t r y
3 0 DESIGN WORLD August 2015 www.designworldonline.com
O f f s h o r e
In two new hovercrafts, the British manufacturer Griffon Hoverwork relies on timing belts with carbon tensile from ContiTech Power Transmission Group. At 5,502 mm (216.6 in.) and 4,956 mm (195.1 in.), they are some of the longest endless polyurethane belts that have ever been produced. They drive the propellers and turbines of the giant hovercrafts, which are employed to connect Portsmouth (England) and the Isle of Wight. The belts are made in cooperation of ContiTech and Griffon Hoverwork at the ContiTech site in Dannenberg.
The two new hovercrafts, which are currently under construction, each have two propellers and fans that interact to set the vessels in motion. The timing belts drive them. Due to the high powers that are transmitted within the drives of the hovercrafts, the Synchrochain Carbon is the ideal belt for this application, said Barrie Oldham, industrial sales director, ContiTech UK. The vessels are equipped with two engines with 793 kW (1,079 hp) of power; they take up roughly the area of a tennis court and carry up to 88 people. Griffon Hoverwork has equipped the drives of their
hovercrafts with timing belts for quite some time. However, the use of the Synchrochain Carbon as well as endless timing belts, which exceed the 5-m mark, are new. The Synchrochain Carbon is wear-resistant and abrasion-proof. It transmits high power reliably. The heart of the belt is the carbon tensile member, which, at the same load, stretches less than an aramid tensile member. In addition, the high stiffness of the cord minimizes pre-tension losses, enhancing drive efficiency. The belt is nearly maintenance free, which helps minimize costs in the area of maintenance and replacement. DW
ContiTech Power Transmission Groupcontitech.de
DFI 8-15_Vs6.LL.MD.indd 30 8/5/15 9:15 AM
800 453-6202
>> Accelerate your productivity at ni.com/embedded-platform
2013 National Instruments. All rights reserved. LabVIEW, National Instruments, NI, and ni.com are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies. 12114
Smarter Embedded Designs,Faster Deployment
The combination of NI LabVIEW system design software and reconfi gurable I/O
(RIO) hardware helps small design teams with varied expertise develop demanding
embedded applications in less time. Using this graphical system design approach,
you can take advantage of the same integrated platform to program embedded
processors and FPGAs for faster application development in industries ranging
from energy to transportation, manufacturing, and life sciences.
LabVIEW system design software offers ultimate fl exibility through FPGA programming, simplifi es code reuse, and helps you program the way you thinkgraphically.
12114 NI_2012_Smarter Embedded Design Ad.indd 1 6/19/13 11:54 AM
Nat'l Instruments 4-15.indd 31 8/4/15 2:36 PM
3 2 DESIGN WORLD August 2015 www.designworldonline.com
D e s i g n f o r I n d u s t r y 04
www.designworldonline.com August 2015 DESIGN WORLD 3 3
s a f e t y
Sensor enhances driver safety
Heres a sensor that will help prevent operators from nodding off or losing focus when driving various types of vehicles. SensoFoil measures position and pressure; it can be added to any steering wheel. This sensing technology adds an extra dimension of safety to steering wheels for car and vehicle manufacturers. During normal driving, the operator is constantly moving their hands on the steering wheel, changing pressure as the fingers grip the wheel. However, by using SensoFoil inside the steering wheel, the vehicle can sense if the drivers hands are no longer movingif the operator has fallen asleep with their hands on the wheel or if their hands are no longer on the wheel. This can trigger the correct safety protocol to either wake up the driver or implement corrective measures. Traffic experts claim that about 25% of all
accidents are caused by extreme fatigue while driving. This makes nodding-off, also referred to as micro-sleep, in combination with heart attacks, as the leading cause of accidents, exceeding the number of accidents caused by alcohol and drugs. Once alerted by the Smart Steering Wheel, the car can try to wake the driver or take control and steer the vehicle to a safe stop along the road. In case of medical emergency, the car could even drive itself to the closest medical emergency center while sending out an alert to the appropriate authorities. The sensor can also be programmed for pressure in certain locations. This can be used in a vehicle to control various location, emergency, entertainment or communication systems. This same feature
can be used in game controllers, aircraft and so on, as an economical way to add additional programmable capabilities to a controller or joystick device without the need for extra buttons or dials. SensoFoil cost-effectively provides extra features and capabilities to a diverse range of products, said Jens Kautzor, CEO of Hoffman + Krippner. In addition, this sensing technology requires very little external energy since power consumption is very low. The sensor system is insensitive to electromagnetic radiation and therefore ideal for the automotive, aerospace and medical sectors. DW
Hoffmann + Krippnerhoffmann-krippner.com
DFI 8-15_Vs6.LL.MD.indd 32 8/5/15 9:15 AM
StepSERVOTM Servo performance at step motor pricesClosed loop for faster response, ideal for high throughput machines
50% more torque
Runs cooler, saves power, lasts longer
866-916-6379www.Applied-Motion.com Email: [email protected] Search or shop online today.
Applied-Motion.com/StepSERVO
Freesamples forqualifying
OEMS
StepSERVOTM combines the best features of stepper and servo systems.
Applied Motion 7-15.indd 33 8/4/15 2:37 PM
Servo controllers commonly use a cascaded configuration, in which a velocity
loop is nested within a position loop. The
velocity controller is tuned first, then the
position controller. The current control
parameters are usually set automatically.
The position controller typically consists of
a simple proportional coefficient, while the
velocity controller includes a proportional
coefficient and an integral term.
A drawback of this configuration is an
intrinsic tracking error during movement
proportional to the speed. Feed-forward
methods tend to reduce this error, but at the
expense of an overshoot or a longer settling
time.
To overcome these limitations, Servotronix
Motion Control developed an adaptive
non-linear control algorithm. Named HD
Control (HDC), this algorithm uses a parallel
configuration, in which all branches are on
the same level and executed in each sampling
period. On each branch, a variable gain
parameter is introduced and automatically
optimized for high gain and stability,
minimizing position error and settling time.
The algorithm consists of a variable gain
module, which contributes to a low tracking
error, and an adaptive feed-forward module,
3 4 DESIGN WORLD August 2015 www.designworldonline.com
Servo controller finds the right rhythm
The Servotronix design te
am uses
the HDC adaptive non-linea
r control
algorithm for the CDHD serie
s of servo
controllers.
Mike Santora Associate Editor D e s i g n N o te s
Design Notes 8-15_Vs8.LL.MS.MD.indd 34 8/5/15 9:59 AM
which allows a short settling time.
The variable gains (VGd, VGp, VGiv, VGi) are
calculated internally and modified dynamically
during operation by the HDC algorithm. Each
gain is a specific function of the system
variables, such as velocity and position error.
During movement, the variable gains may reach
values up to ten times higher than at stop. This
produces highly accurate path-following during
movement, together with quiet low-speed
operation and standstill. System stiffness is
more than tripled during movement, resulting
in low tracking error.
The four variable gains are balanced by
a proprietary algorithm that maintains the
stability of the system. The Kd (derivative)
parameter branch is comparable to the velocity
feedback loop, and serves to reduce velocity
error. The Kp parameter branch is a proportional
position feedback loop, for reducing position
error. The Ki parameter branch is an integral of
the position feedback loop, reducing standstill
error.
The Kiv parameter branch is unique to HDC
and combines the effects of the Kp and Ki
branches. It produces a stiffness more than
double that of Kp, without creating oscillations.
It reduces the tracking error during both
acceleration and standstill. It also eliminates
standstill error, as does Ki, but with the rapid
response time of Kp.
The adaptive feed-forward module
helps achieve a short settling time. During
movement, the correspondence between
acceleration and motor torque is monitored,
and this relation is used during the deceleration
phase to process the integral term. At the
end of movement, the adaptive feed-forward
algorithm modifies the content of the
integral term according to the expected path
acceleration, resulting in a zero settling time.
HDC is integrated in the Servotronix
CDHD servo drive series. Tuning is performed
automatically by the CDHD interface software,
ServoStudio. While autotuning is usually
sufficient, certain applications may require
manual fine tuning for the optimization of
control parameters.
Automatic and manual tuning is based
on the same principle. During autotuning,
the quality of the movement is measured
and evaluated by the drive and the software.
During manual tuning, the quality of movement
is evaluated by the user. In either method,
the servo control parameters are modified
progressively and the value that achieves the
best performance is selected.
HDC tuning is simple and is performed
much like conventional PID tuning. Each
variable gain is increased progressively until
some oscillation occurs, then reduced about 10
to 20% to a safe value.
For instance, one gantry robotic
application required a sustained accuracy
of 2 to 3 m at maximum speed. Using the
CDHD servo drive with the HDC algorithm, the
maximum application speed was increased
from 120 to 160 mm/sec while maintaining
the required accuracy, and resulted in a 33%
increase in machine throughput.
HDC can be advantageous in applications
requiring path tracking and low settling time,
such as CNC and cutting, conveyor tracking,
pick-and-place operations, PCB mounting and
welding, as well as painting, coating and gluing.DW
Servotronix Motion Controlservotronix.com
This image shows
a simplified diagram of
HD Control.
August 2015 DESIGN WORLD 35
Design Notes 8-15_Vs8.LL.MS.MD.indd 35 8/5/15 9:59 AM
Mike Santora Associate Editor
I want one thing to do a lot of things. If theres a mantra for the 21st-century
consumer, this is it. Swiss Army knives are on
the map for multi-purpose functions. Its why
we call smartphones smart. The problem is
that consumers want all this multi-function
wizardry and they want ease-of-use as well.
These concerns topped the list when
Watlow designed its new F4T temperature
process controller. The primary goal for
the development of the new device was to
ensure that it would be easy to use without
sacrificing application flexibility. Because
many of Watlows target customers were
already using its SERIES F4 controller, the
bar was set high for ease-of-use. The F4Ts
color, graphical touchscreen user-interface
and configuration software had to let OEMs
and end users tailor the controller to specific
applications.
The F4T controller combines the
functions of many devices, including
temperature PID, over/under temperature
limit, power switching, math, logic, and
timers and counters into one integrated
system. The controller has field pluggable
I/O, programmable function blocks and an
ambient operating temperature of 0 to 122
F. For connectivity, the F4T has a graphical
configuration PC software that connects
with the controller through Ethernet. It
also has agency certifications such as UL,
FM, CE, RoHS, W.E.E.E. and NEMA 4X/IP65.
Communications options include Ethernet
Modbus TCP and SCPI and EIA 232/485
Modbus RTU.
Clearly, many challenges come into
play when developing a product with such
a density of features. The F4T requires
time critical measurements, advanced
control algorithms, support for industrial
communications protocol interfaces,
management of multiple tasks in embedded
software, field pluggable I/O hardware,
onboard agency-approved safety devices and
robust mechanical design.
User experience is often a factor for
design teams, but its not always central to
the design efforts. The challenge for the F4T
team was to design for ease-of-use without
delaying product development.
The team started by defining their type
of usersoperators, OEM engineers, lab
D e s i g n N o te s
3 6 DESIGN WORLD August 2015 www.designworldonline.com
managers and line-maintenance technicians.
People in these roles participated in testing
to help the F4T team lay out the functions
and features of the interface. For example, in
an initial card-sort test, the subjects sorted
operations and functions, such as changing
the temperature units, into categories they
defined themselves such as operation, set-
up and maintenance.
Based on these tests, the F4T team
developed a grouping of information
and controls for each of the tasks. This
organization served as a blueprint for the
interface. From there, a wire-frame prototype
was developed with several iterations tested
internally. Next, an HTML-based prototype
was developed and tested by samples of the
target user populations.
The next challenge was getting a product
that was still in development into the hands
of test groups. The usability testing was
performed through web-based conferences
The F4Ts color, graphical touchscreen user-interface and configuration soft-ware let OEMs and end users tailor the controller to specific applications.
How to make a temperature controller easy to use
Design Notes 8-15_Vs8.LL.MS.MD.indd 36 8/5/15 9:58 AM
with a moderator administering a scripted
test in which subjects interacted with the
prototype using a web browser and mouse.
The moderator asked the subject to perform
tasks such as, Can you show me how you
would change the humidity set point?
Measurements included successfully
completed tasks in a preset amount of time
and how often users made wrong turns. After
each set of tasks, users were asked follow-up
questions to determine if they understood
what they had seen. They were then asked to
rate the ease-of-use of the functions. These
test sessions were observed by the F4T team
so they could directly witness the users
frustrations when features were not easy
The F4T process controller has field pluggable I/O, programmable function blocks and an ambient operating temperature of 0 to 122 F. The F4T also has graphical configuration PC software that connects with the controller through Ethernet.
ADDITIVE MANUFACTURING
CNC MACHINING
INJECTION MOLDING
Get a free Rapid Manufacturing for Metal Parts white paper at go.protolabs.com/DW5PKISO 9001:2008 Certified | ITAR Registered Major Credit Cards Accepted | 2015 Proto Labs, Inc.
CNC Machining That Doesnt
Just Mill Around
Got a project? Get up to 200+ parts in 1 to 3 days.
Never lose valuable development time again. Proto Labs uses CNC turning and three-axis CNC milling to manufacture engineering-grade metal and plastic
prototypes in as fast as 24 hours.
Design Notes 8-15_Vs8.LL.MS.MD.indd 37 8/5/15 10:00 AM
D e s i g n N o te s
3 8 DESIGN WORLD August 2015 www.designworldonline.com
WHAT DO YOU THINK?
Connect and discuss this and other design engineering issues with
thousands of professionals online
even created. Typically the user-interface
is the last thing you can put in the product.
But had the Watlow designers waited until
the touchscreen was functioning to begin
testing, it would have delayed the product and
comprised the ease-of-use. Their approach
is a great example of how to develop an
interface parallel with the hardware and
software. The testing and the prototypes cost
much less than actual product iterations,
saving time and money and creating better
end results. DW
Watlowwatlow.com
to use. The prototype was updated as they
discovered the problem areas.
The same process was applied to the
Composer software that can be used to set
up the F4T. The software testing also shed
light on areas that could be adjusted. In
one example, a subject was unable to find
a button on a screen that was required to
complete a task. By debriefing the participant
and reviewing the recording, designers were
able to determine that the color combination
(white text on a grey background) and
placement of the button (low on the screen)
was causing a problem. The farsighted
participant had trouble with this when using
a laptop with an LCD monitor. To make the
button easier to locate, the team moved the
button and changed the color combination to
a higher contrast (white text on dark blue). In
future tests, this problem no longer occurred.
After this testing, the F4T team refined
the interface design before the product was
The F4T connectivity options include two USB host ports, Ethernet Modbus TCP and SCPI, 232/485 Modbus RTU and a USB device port.
Design Notes 8-15_Vs8.LL.MS.MD.indd 38 8/5/15 10:01 AM
CM
Y
CM
MY
CY
CMY
K
DesignWorld_MDrive_ad_2015.ai 1 4/28/2015 9:33:15 AM
Schneider Electric 7-15.indd 39 8/6/15 1:59 PM
August 2015 DESIGN WORLD 41
4 0 DESIGN WORLD August 2015 www.designworldonline.com
D e s i g n N o te s
Steel producers worldwide continually refine their processes to serve the changing needs of their customers. For example,
Federal emission standards and consumers demand more efficient
vehicles without compromising performance and styling. In
response, steel producers have begun to develop thinner, lighter
weight auto gage steels that perform as well and look better than
previous materials. However, producing a specialty steel cost
effectively is always challenging, particularly when incorporating
new alloy technology that is designed to be stronger yet lighter
than previous steels. These thinner steels are much more sensitive
to surface damage from vibrations of rotating mill rolls.
To reduce the damage caused by vibration, operators often
reduce the speed of their mills by up to 20%, which reduces
production. That 20% production reduction can equate to one 20-ton
coil of steel per hour that would have had a $50/ton profit, which
would have delivered a $24,000 profit.
Thus, the financial losses associated with steel surface
damage due to mill vibration can be significant. To understand
why mill operators are eager to convert to U-joints, consider the
following example: Surface-critical exposed prime steel sells for
approximately $850/ton. If the surface is marred or damaged, the
steel is downgraded to secondary, non-exposed usage with a 20%
($170/ton) reduction in price. Typical annual cold mill production
is around 3 mil tons. If only 2% of the product is downgraded, that
equates to 60,000 tons. So, 60,000 tons minus $170/ton yields a
total annual loss of a staggering $10.2 mil.
Universal joints help reduce mill vibration
One steel producer was experiencing excessive wear and
vibration of the gear spindles on their 5-stand tandem cold mill with
various spindle brands lasting only six months. Two spindles on
each mill stand connect the pinion gearboxes to the primary upper
and lower work rolls that compress the steel in a cold condition.
Over time the surface damage to the steel from the spindle vibration
(chatter) caused the operator to either slow the mill down, reducing
production by 20% to reduce the vibration, or replace the spindles
completely. The motor drives a gear box that connects to the pinion
stand single input shaft. The u-joints connect the two pinion stand
outputs to the work rolls that roll the steel sheet.
Thats why Ameridrives Power Transmission was called to
provide a more reliable spindle. Soon after, Ameridrives application
engineers approached the mill with a new idea. They recommended
that all the gear spindles be converted to universal joints, which
would reduce surface damaging vibration almost completely, while
allowing the mill to run at faster speeds. After testing competitive
models, the mill selected Americardan Model U3440 universal
joints. The mill was then able to run at record-setting production
levels with reduced vibration and minimal related surface damage.
The new U-joints reduced lubrication manpower, lube and clean-up
costs by approximately $120,000 annually compared to a grease
lubricated gear spindle on a 5-stand mill.
Americarden Model U3440
units feature 553,000 Nm torque
capacity, special carburized steels
and custom bearing steel rollers.
Edited by: Mike Santora Associate Editor
Design Notes 8-15_Vs9.LL.MS.MD.indd 40 8/5/15 10:12 AM
August 2015 DESIGN WORLD 41
Ameridrives engineers work closely with steel mill
operators around the world to replace their cold mill gear
spindles, which amplify vibration, as they drive the work
rolls on the mill stands.
Americardan universal joints operate at high
misalignment angles up to 15 and are suitable for use
in severe atmospheric conditions. Through materials and
tight tolerances, the universal joints have proven to reduce
vibration levels in rolling mills. Universal joint design
features include closed eye one-piece yokes, replaceable
inner race bearing package, zero radial clearance bearing
package and built-in spring packs on the roll end knuckle.
Spring packs are non-contacting in operation and
are only engaged during roll change. You can mate
the spline adapters to the gear spindle at the pinion
end. This approach can be used without removing the
adapter, which speeds installation. These units can be
interchanged with any gear spindle in any mill stand, in
top or bottom position, at any time. DW
Altra Industrial Motionaltracouplings.com
These graphs illustrate the reduction
in vibration before and after using the
Americarden universal joints.
WHAT DO YOU THINK?
Connect and discuss this and other design engineering issues with
thousands of professionals online
P.O. Box 9070 Fort Wayne, IN 46899 USA
To order a catalog and see more solutions, visitphdinc.com/dw8151-800-624-8511
Pneumatic, hydraulic, and electric actuators Lowest cost of ownership 1-3 day delivery on most products Free online engineer tools MAC Distribution Network Modular solutions ClampsClamps
And Now Even More...
Design Notes 8-15_Vs9.LL.MS.MD.indd 41 8/7/15 10:21 AM
C A E S o lu t i o n s
42 DESIGN WORLD August 2015
C A E S o lu t i o n s
The latest generation of Inspire combines faster geometry functions with an updated user interface and expands the scope and complexity of problems it can address. Several new functions have been added based on the most common requests from the Inspire user community. These include: fasteners (bolts or screws), joints (pins or sliding pins), and contacts (bonded, contact or no contact). Leveraging these capabilities, users can easily model, optimize and analyze model assemblies. Inspire Rely lets users realistically simulate loading conditions. It also offers support for assembly optimization, which lets you incorporate a surrounding structure into the optimizations and gain a deeper understanding of the relationship between multiple components.
Key updates include: Fasteners and jointsConnect multiple parts in a model using bolts, screws, pins or sliding pins. Inspires workflow identifies areas in the model with aligned holes to make the process easy and intuitive. ContactsDesignate whether neighboring parts should be bonded, contacting or have no contact for more realistic optimization results. Gravity loadsAdd G loads to a model through the Model Browser. Updated user interfaceA new ribbon-style interface organizes the tools into tabs. Customize the tabs to tailor the workflow to your process. Faster geometry functionsGeometry functions in the program are running up to 300% faster than previous versions of Inspire. DW
SolidThinkingaltair.com
Topology design program is faster, more accurate and supports assemblies
CAE Solutions_Simulations 8-15_Vs4.LL.MD.indd 42 8/13/15 3:08 PM
Your Custom Gearbox Solutionsare CGI Standard Products.
Advanced Products for Robotics and AutomationCGI Motion standard products are designed with customization in mind. We understand most off-the-shelf products or a complete
in-house design may not fi t your application, so our standard products are designed for functional fl exibility. Our team of experts will
work with you on selecting the optimal base product and craft a unique
solution to help differentiate your product or application. So when you think
customization, think standard CGI gearbox assemblies. Connect with us today
to explore what CGI Motion can do for you.
800.568.GEAR (4327) www.cgimotion.comcopyright2015 cgi inc. all rights reserved. 0804stdp
CGI 8-15.indd 43 8/6/15 2:20 PM
4 4 DESIGN WORLD August 2015 www.designworldonline.com
C A E S o lu t i o n s
CAM education credentials
Autodesk, developers of 3D design, engineering and entertainment software, and the National Institute for Metalworking Skills (NIMS) are partnering to develop the first set of industry recognized Computer Aided Manufacturing/Machining (CAM) standards and credentials. These standards and credentials will enhance education and training programs to meet 21st-century demands for skilled CAM programmers, designers and engineers, which will account for almost 100,000 new jobs by 2024. To stay competitive, manufacturers must maintain high standards of production at efficient cost while meeting the ever-changing customer demands for their products. CAM allows manufacturers to efficiently adjust their processes to identify optimal production paths that decrease cycle times, reduce scrapped parts and materials, and improve the quality of finished parts. Skilled CAM programmers, designers and engineers with extensive education and training are in high demand to plan, manage and control these sophisticated and costly machines. Companies in technologically advanced industries are becoming
Recommended