® Toyota, Lexus and Scion are registered trademarks and property of their respective companies.
Vehicle Application Guide................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Type 1..............................................................................................................................................................................Type 2..............................................................................................................................................................................Type 3..............................................................................................................................................................................Type 4..............................................................................................................................................................................Type 5..............................................................................................................................................................................Type 6..............................................................................................................................................................................
ProgrammingModule Programming......................................................................................................................................................Module Reset...................................................................................................................................................................Hard Reset.......................................................................................................................................................................Feature and Option List...................................................................................................................................................Feature Programming......................................................................................................................................................
LED Diagnostics and Troubleshooting............................................................................................................................
Limited One-Year Consumer Warranty............................................................................................................................
Quick Reference Guide...................................................................................................................................................
02
030508101214
1617171818
19
21
22
Index
Installation Guide
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
The TL4 firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Toyota and Lexus vehicles.
This module can only be flashed and configured using XpressVIP at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on page 16 for more information.
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Vehicle Application GuidePage 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
Vehicles
2015
2014
2013
2012
2011
2010
2009
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
FO
B-C
ontr
olo
fafterm
ark
etala
rm
with
OE
Mre
mote
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
h
Pin
SS
-Facto
ryA
larm
Trigger
Monito
ring
ST
-Bra
ke
Sta
tus
(footbra
ke)
ST
-E-B
rake
Sta
tus
ST
-Igniti
on
Sta
tus
Lexus
GS 350 (Smart Key) 1 1 1 • D • • • • D • • •
GS 460 (Smart Key) 1 1 1 • D • • • • D • • •
IS 250 (Smart Key) 4 4 4 4 4 • D • • • D • •
IS 250C (Smart Key) 4 4 4 4 4 4 • D • • • D • •
IS 350 (Smart Key) 4 4 4 4 4 • D • • • D • •
IS 350C (Smart Key) 4 4 4 4 4 4 • D • • • D • •
Scion
tC (Smart Key) 2 2 • D • • • • D • • •
Toyota
Avalon (Smart Key) 6 6 3 • D • • • • D • • •
FJ Cruiser (G Key) 5 5 5 5 5 • D • • • • D • • •
FJ Cruiser (L Key) 5 5 5 5 5 • D • • • • D • • •
Legend:
•: D2D & Wire-to-Wire (W2W)
D: Data-to-Data
PK: Transponder & Immobilizer Override
FOB: Sync CAN Interface w/ FOB Remote
RS: Remote Start & Engine Controls
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
© 2012 Directed. All rights reserved.
[1] (AC) Tach Input(-) Trunk Status Input(-) Door Status Input
(-) E-Brake Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(-) Lock Output [2]
(-) Trunk Release Output [2]
(-) Unlock Output [2]
(+) 12V
(-) Parking Lights Output
(-) Hood Status Input
(-) Ground
(+) Brake Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) E-Brake Status Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
IMI Data: Yellow/Black: 10
IMI Interrupt (vehicle side): Orange/Red: 10
IMO Data: Orange/Black: 11
IMI Interrupt (conn. side): Yellow/Red: 11
(-) Hood Status Output: Blue/Red: 12
IMI: Lt. Green, pin 49
IMO: Pink, pin 48
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
(+) 12V: Red: 13(+) 12V
(-) Ground (-) Ground: Black: 14
Not required in D2D mode.
If the module programs but the vehicle starts and stops after remote starting, reverse IMI wires.
Yellow/Black and Yellow/Red wires needs to be on the ECM side.
Autolights Off: Orange/Yellow: 9
Autolights Off: Yellow: 8
Diagnosticconnector OBDII
(connector side view)
1 8
169
CAN High, Blue, pin 6
CAN Low: Lt. Green, pin 14
12345678910
1112131415161720 19
(-) Autolights: Orange, pin 19
(-) Parking Lights: Blue, pin 18
Headlight Switch(White conn. at headlight switch)
(+) Starter 1 Output
(+) Starter 2 Output
(+) Ignition 1 Output
(+) Ignition 2 Output
(+) Accessory Output
Power ECU(White conn. behind glove box)
Fuse Box(White conn. under
driver dash)
1
(+) Accessory 1: Green, pin 11
(+) Ignition 2: Yellow, pin 35 (+) Ignition 1: Lt Blue, pin 34
(+) 12V: White, pin 1
[2] (-) Trunk Release: Blue, pin 21
(+) Starter 1: Blue, pin 15
(+) Starter 2: Lt Blue, pin 17
26 25 24 2322 181920
7891011121314151617
123456
Power ECU(White conn. behind
glove box)
21
18
123456789
262728293031
10131214163240 39 38 37 36 1819202122232425
17 11153435
CUT
Junction connector(White conn. drivers kick panel)
50 472526
102711 91213141516171819202122
3837363534333231302960595857565554535251
284624
8
45237 123456
444342 4140394849
[2] (-) Unlock/Disarm: Pink, pin 13
1
11
10
20
Driver Door Window Switch(White conn in drivers door)
4
13
[2] (-) Lock/Arm: Lt.Green, pin 4
Cut
[2] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
XKD2D65TX
(-) Ground
RX(+)12V
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
Installation Type 1
10
4
14
12
2
DBALL2
RF
Prog. Button
LED
Page 3
Autolights connection on required in vehicles with autolights.
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Type 1 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Lexus GS 350 (Smart Key) 2009-2011
12V White 1 (+) Driver Dash Fuse Box. White 1
CAN H Blue 6 Data OBDII. White 16
CAN L Lt. Green 14 Data OBDII. White 16
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Yellow 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Lt. Blue 34 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Green 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Lt. Blue 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Blue 15 (+) Power Source Control ECU behind glove box. White 40
IMO Pink 48 Data Driver Kick Panel. White 60
IMI Lt. Green 49 Data Driver Kick Panel. White 60
Lock Lt. Green 4 (-) Power Window Master Switch in driver door. White 20
Unlock Pink 13 (-) Power Window Master Switch in driver door. White 20
Trunk Release Blue 21 (-) Body ECU (RH) behind glove box. White 26
Lexus GS 460 (Smart Key) 2009-2011
12V White 1 (+) Driver Dash Fuse Box. White 1
CAN H Blue 6 Data OBDII. White 16
CAN L Lt. Green 14 Data OBDII. White 16
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Yellow 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Lt. Blue 34 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Green 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Lt. Blue 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Blue 15 (+) Power Source Control ECU behind glove box. White 40
IMO Pink 48 Data Driver Kick Panel. White 60
IMI Lt. Green 49 Data Driver Kick Panel. White 60
Lock Lt. Green 4 (-) Power Window Master Switch in driver door. White 20
Unlock Pink 13 (-) Power Window Master Switch in driver door. White 20
Trunk Release Blue 21 (-) Body ECU (RH) behind glove box. White 26
Connector Information
Page 4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Standard connections from remote starter to vehicle are required. Refer to Main Remote Starter
Connections - Type2 (next page)
Rem
ote
Sta
rter
(+) Starter: White, pin 3
(+) 12V
(+) Starter Output
(+) Ignition 1 Output
(+) Ignition 2 Output(+) Accessory Output
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) E-Brake Status Output: Black/White: 1
[2] Security Light Output: Green/Black: 2
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
IMI Interrupt (vehicle side) : Orange/Red: 10
IMI Interrupt (conn. side): Yellow/Red: 11
(-) Hood Status Output: Blue/Red: 12
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
(+) 12V: Red: 13
(-) Ground (-) Ground: Black: 14
[1] (AC) Tach Input(-) Trunk Status Input(-) Door Status Input
(-) E-Brake Status Input
(-) GWR (Status)
(-) Hood Status Input(+) Brake Input
Diagnosticconnector OBDII
(connector side view)
1 8
169
CAN High, Lt. Green, pin 6
CAN Low, White, pin 14
IMI: Green, pin 11
IMO: Tan, pin 10
If the module programs but the vehicle starts and stops after remote starting, reverse IMI wires.
Yellow/Black and Yellow/Red wires need to be on the ECM side.
IMI Data : Yellow/Black: 10IMO Data: Orange/Black: 11
Security Light(White conn. behindclock assembly)
18
16 911
[2] (-) Security Light: Gray, pin 11
ECM(Black conn. under the hood)
123202122
313233
4
1219
2330
3441
4249
5360 52 51 50
11 10
(-) Lock Output [3]
(-) Trunk Release Output [3]
(-) Unlock Output [3]
1
12
11
Junction Connector(White conn.
driver kick panel)
22
[3] (-) Trunk Release: Gray, pin 22
Junction Connector(Blue conn. driver kick panel)
2
7
1112
[3] (-) UnlockGreen, pin 12
[3] (-) LockBlue, pin 11
(+) 12V
Not required in D2D mode.
1
11
10
20
Headlight Switch(White conn.
at headlight switch)
(-) Parking Lights:Violet, pin 18
18
(-) Parking Lights Output
192021 222324 252627 282930
1 2 4 5 6
7 8 9 101112 131415 161718
3
Power ECU(Gray conn. behind glove box)
(-) Ground
Installation Type 2Page 5
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
XKD2D65TX
(-) Ground
RX(+)12V
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
[2] This connection is ONLY required if the security light in the vehicle is ON following its remote start. Not required on all vehicles.[3] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.
Cut
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Page 6
Main Remote Start Connections - Type 2
2 1
1
2G
2F
2A
2B
2C
2D
(from Engine RoomMain Wire)
(from Roof Wire)
(from Floor Wire)
(from Engine RoomMain Wire)
(from Instrument Panel Wire)
(from InstrumentPanel Wire)
1
6
13
18
7
12
19
24
1
2
3 645
78
1
4
11
16
26
31
17
25
32
40
1 13 31
6 21 39
7 22 40
12 30 48
1
6
7
8
9
17
15
23
24
26
27
35
36
44
45
47
48
56
10
(+) Accessory: Black, pin 25
(+) Ignition 2: Gray, pin 26
(+) Ignition 1: Red, pin 5
(+) 12V: pin 1
5
2526
Rear of fuse box
Rem
ote
Sta
rter
(+) 12V
(+) Ignition 1
(+) Ignition 2(+) Accessory
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Type 2 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Scion tC (Smart Key) 2011-2012
12V White 1 (+) Dash Fuse Box, connector (2G). White 1
CAN H Lt. Green 6 Data OBDII. White 16
CAN L White 14 Data OBDII. White 16
Security Light Gray 11 (+) Clock Assembly. White 16
Parking Lights Violet 18 (-) Headlight Switch. White 20
Starter White 3 (+) Power Source Control ECU behind glove box. Gray 30
Ignition 1 Red 5 (+) Dash Fuse Box, connector (2B). White 40
Ignition 2 Gray 26 (+) Dash Fuse Box, connector (2C). White 48
Accessory Black 25 (+) Dash Fuse Box, connector (2C). White 48
IMO Tan 10 Data ECM next to underhood fuse box. Black 60
IMI Green 11 Data ECM next to underhood fuse box. Black 60
Lock Blue 11 (-) Driver Kick Panel. Blue 12
Unlock Green 12 (-) Driver Kick Panel. Blue 12
Trunk Release Gray 22 (-) Driver Kick Panel. White 22
Connector Information
Locating Components in the Vehicle - Type 2
ECM (Engine Control Module)
Engine Compartment
Page 7
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
7
1
12
23
131415161718
4569 1120
10
19
Not required in D2D mode.
[1] (AC) Tach Input(-) Trunk Status Input(-) Door Status Input
(-) E-Brake Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(-) Lock Output [2]
(-) Trunk Release Output [2]
(-) Unlock Output [2]
(+) 12V
(-) Hood Status Input
(-) Ground
(+) Brake Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) E-Brake Status Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
IMI Data: Yellow/Black: 10
IMI Interrupt (vehicle side): Orange/Red: 10
IMO Data: Orange/Black: 11
IMI Interrupt (conn. side): Yellow/Red: 11
(-) Hood Status Output: Blue/Red: 12
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
(+) 12V: Red: 13(+) 12V(-) Ground (-) Ground: Black: 14
If the module programs but the vehicle starts and stops after remote starting, reverse IMI wires.
Yellow/Black and Yellow/Red wires needs to be on the ECM side.
Autolight Off: Orange/Yellow: 9
Autolight Off: Yellow: 8
(+) Ignition 1 Output
(+) Ignition 2 Output
(+) Accessory Output
Fuse Box(White conn.
under driver dash)
1
(+) Ignition 2: Yellow, pin 35 (+) Ignition 1: Lt Green, pin 34
(+) 12V: Black, pin 1
[2] (-) Unlock: Gray, pin 19
[2] (-) Trunk Release: Blue, pin 5
[2] (-) Lock: Black, pin 9
Junction Connector
(White conn. behind
glove box)
18
151413
73 4 5 6
981 2
12
11
IMI: Tan, pin 11
IMO: Green, pin 10
Junction Connector(White conn. drivers kick)
Trunk Release Switch(White conn. at release switch)
16 4 3 25
12345678910
1112131415161720 19
(-) Parking Lights: Blue, pin 18
White connector(at headlight switch)
18
(-) Parking Lights Output
(-) Autolight:Orange,pin 19
Diagnosticconnector OBDII
(connector side view)
1 8
169
CAN High: Pink, pin 6
CAN Low: White, pin 14
(+) Starter 1 Output
(+) Starter 2 Output
Power ECU(White conn. behind glove box)
(+) Starter 1: Black, pin 17
(+) Starter 2: Lt Blue, pin 1519
2610
3240 1817 1115
3435
(+) Accessory 1: Red, pin 11
8
Installation Type 3Page 8
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
XKD2D65TX
(-) Ground
RX(+)12V
Cut
Cut
[2] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
17
16
10
Autolights connection on required in vehicles with autolights.
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Type 3 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Toyota Avalon (Smart Key) 2010
12V Black 1 (+) Dash Fuse box. White 1
CAN H Pink 6 Data OBDII. White 16
CAN L White 14 Data OBDII. White 16
IMO Green 10 Data Behind Glove Box. White 18
IMI Tan 11 Data Behind Glove Box. White 18
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Yellow 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Lt. Green 34 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Red 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Black 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Lt. Blue 15 (+) Power Source Control ECU behind glove box. White 40
Lock Black 9 (-) Driver Kick Panel. White 20
Unlock Gray 19 (-) Driver Kick Panel. White 20
Trunk Release Blue 5 (-) Trunk Release Switch. White 6
Connector Information
Page 9
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Not required in D2D mode.
[1] (AC) Tach Input(-) Trunk Status Input(-) Door Status Input
(-) E-Brake Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(-) Lock Output [2]
(-) Trunk Release Output [2]
(-) Unlock Output [2]
(+) 12V
(-) Ground
(+) Brake Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
IMI Data: Yellow/Black: 10
IMI interrupt (vehicle side): Orange/Red: 10
IMO Data: Orange/Black: 11
IMI interrupt (conn. side): Yellow/Red: 11
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
(+) 12V: Red: 13(+) 12V
(-) Ground (-) Ground: Black: 14
If the module programs but the vehicle starts and stops after remote starting, reverse IMI wires.
Yellow/Black and Yellow/Red wires needs to be on the ECM side.
Autolight Off: Orange/Yellow: 9
Autolight Off: Yellow: 8
(+) Ignition 1 Output
(+) Ignition 2 Output
(+) Accessory Output
Passenger Fuse Box(White 1-pin conn.)
1
(+) Accessory 1: Lt Green, pin 11
(+) Ignition 2:Pink, pin 34
(+) Ignition 2: Lt Green, pin 35
(+) 12 V: Black/White,pin 1
[2] (-) Trunk Release: Pink, pin 6
IMI: Pink, pin 14
IMO: White, pin 15
Trunk Release Switch(White conn. at release switch)
16
White 60-pin Conn. (driver kick panel, the top white 60-pin connector)
Parking Brake Switch(Brown conn.
at parking brake)
112 7
23
4550
28
51
29
1322
38
60
6
44 39
1415
12345678910
1112131415161720 19
(-) Parking Lights: Blue, pin 18
Headlight Switch(White conn. at headlight switch)
18
(-) Autolight:Orange,pin 19
(-) Parking Lights Output
Diagnosticconnector OBDII
(connector side view)
1 8
169
CAN High: Green, pin 6
CAN Low: White, pin 14
Power ECU(White conn. behind glove box)
1926
103240 18
17 11153435
(+) Starter 1 Output
(+) Starter 2 Output
(+) Starter 2: Lt Blue, pin 17
(+) Starter 1: Violet, pin 15
1
Only for manual transmissions
[2] (-) Unlock: Pink, pin 13
1
11
10
20
Driver Power Window Switch(White conn. in drivers door)
4
13
[2] (-) Lock: Lt.Green, pin 4
Cut
Not required in D2D mode.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
XKD2D65TX
(-) Ground
RX(+)12V
[2] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Installation Type 4
Parking Brake: Yellow, pin 1
Page 10
Cut
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Type 4 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Lexus IS 250 (Smart Key) 2009-2013
Parking Brake Yellow 1 (-) Parking Brake Switch. Brown 1
12V Black/White 1 (+) Passenger Dash Fuse Box. White 1
CAN H Green 6 Data OBDII. White 16
CAN L White 14 Data OBDII. White 16
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Pink 34 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Lt. Green 35 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Lt. Green 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Lt. Blue 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Violet 15 (+) Power Source Control ECU behind glove box. White 40
IMO White 15 Data Driver Kick Panel. White 60
IMI Pink 14 Data Driver Kick Panel. White 60
Lock Blue 4 (-) Power Window Master Switch in driver door. White 20
Unlock White 13 (-) Power Window Master Switch in driver door. White 20
Trunk Release Pink 4 or 6 (-) Trunk Release Switch. Black 6
Lexus IS 250C (Smart Key) 2010-2015
Parking Brake Yellow 1 (-) Parking Brake Switch. Brown 1
12V Black/White 1 (+) Passenger Dash Fuse Box. White 1
CAN H Green 6 Data OBDII. White 16
CAN L White 14 Data OBDII. White 16
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Lt. Green 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Pink 34 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Lt. Green 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Lt. Blue 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Violet 15 (+) Power Source Control ECU behind glove box. White 40
IMO White 15 Data Driver Kick Panel. White 60
IMI Pink 14 Data Driver Kick Panel. White 60
Lock Blue 5 (-) Power Window Master Switch in driver door. White 20
Unlock White 4 (-) Power Window Master Switch in driver door. White 20
Trunk Release Pink 4 or 6 (-) Trunk Release Switch. Black 6
Lexus IS 350 (Smart Key) 2009-2013
Parking Brake Yellow 1 (-) Parking Brake Switch. Brown 1
12V Black/White 1 (+) Passenger Dash Fuse Box. White 1
CAN H Green 6 Data OBDII. White 16
CAN L White 14 Data OBDII. White 16
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Lt. Green 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Pink 34 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Lt. Green 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Lt. Blue 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Violet 15 (+) Power Source Control ECU behind glove box. White 40
IMO White 15 Data Driver Kick Panel. White 60
IMI Pink 14 Data Driver Kick Panel. White 60
Lock Blue 4 (-) Power Window Master Switch in driver door. White 20
Unlock White 13 (-) Power Window Master Switch in driver door. White 20
Trunk Release Pink 4 or 6 (-) Trunk Release Switch. Black 6
Lexus IS 350C (Smart Key) 2010-2015
Parking Brake Yellow 1 (-) Parking Brake Switch. Brown 1
12V Black/White 1 (+) Passenger Dash Fuse Box. White 1
CAN H Green 6 Data OBDII. White 16
CAN L White 14 Data OBDII. White 16
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Lt. Green 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Pink 34 (+) Power Source Control ECU behind glove box. White 40
Connector Information
Page 11
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
[1] (AC) Tach Input(-) Trunk Status Input(-) Door Status Input
E-Brake Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(-) Hood Status Input
(-) Ground
(-) Parking Light Output
(+) Brake Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5(+) Brake Output: Gray: 6
(-) E-Brake Status Output: Black/White: 1[4] Security Light Output: Green/Black: 2
(-) Door Status Output: Green/White: 3(-) Trunk Status Output: Red/Black: 4
IMI Data: Yellow/Black: 10
IMI Interrupt (vehicle side): Orange/Red: 10
IMO Data: Orange/Black: 11
IMI Interrupt (conn. side): Yellow/Red: 11
(-) Hood Status Output: Blue/Red: 12
9: Pink: (+) Ignition Input
6: White/Black: (-) Rearm Input [2]
10: Blue/White: (-) GWR (Status) Input
The 10-pin harness (-) Rearm Input wire should ONLY be connected in D2D mode.
(+) 12V: Red: 13(+) 12V
(-) Ground (-) Ground: Black: 14
Not required in D2D mode.
Autolight Off: Orange/Yellow: 9
Autolight Off: Yellow: 8
Diagnosticconnector OBDII
(connector side view)
1 8
169
CAN High: Pink, pin 6
CAN Low:Violet, pin 14
(-) Autolight:Blue, pin 12
(-) Parking Light:Green, pin 14
(-) Rearm Output
Standard connections from remote starter to vehicle are required.
Refer to ‘Vehicle Wiring Reference Chart’.
(+) 12V
(+) Ignition 1 Output
(+) Ignition 2 Output(+) Accessory Output
Junction Connector(White conn. behind glove box)
Security Light (White conn. A/C Assembly)
123456
789101112
13161718
1921222324
25262728
34
29
35
30
36 313233
1415
20
IMO: Blue/Orange, pin 20
IMI: Blue/Yellow, pin 14
[4] Security Light: Violet/White, pin 15
1 2 3 4 5 6 7 8 9 1011121314151617181920
If the module programs but the vehicle starts and stops after remote starting, reverse IMI wires.
Yellow/Black and Yellow/Red wires needs to be on the ECM side.
1
91016
7 615141312 11
5 48
17
23
Installation Type 5
XKD2D65TX
(-) Ground
RX(+)12V
[2] In the case where a combo security alarm/remote starter is installed and the aftermarket remote is not being used (e.g. SmartStart), connect the (-) Rearm Input wire in order to arm the combo system when remote starting the vehicle.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Page 12
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
10
DBALL2
RF
Prog. Button
LED
4
14
12
2
Cut
Cut
Headlight Switch(White conn. at headlights switch)
Autolights connection only required in vehicles with autolights
[3] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.[4] This connection is ONLY required if the security light in the vehicle is ON following its remote start. Not required on all vehicles.
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Type 5 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Toyota FJ Cruiser (G Key) 2010-2014
12V Blue/Black 7 (+) Ignition Switch. White 8
Ignition 1 Black/Red 6 (+) Ignition Switch. White 8
Ignition 2 Blue/Yellow 4 (+) Ignition Switch. White 8
Accessory 1 White/Green 3 (+) Ignition Switch. White 8
Starter 1 Green/Black 8 (+) Ignition Switch. White 8
Starter 2 Black/White 1 (+) Ignition Switch. White 8
CAN H Pink 6 Data OBDII. White 16
CAN L Violet 14 Data OBDII. White 16
Parking Lights Green 14 (-) Headlight Switch. Black 17
Autolights Blue 12 (-) Headlight Switch. Black 17
Security Light Violet/White 15 (+) A/C Amplifier behind radio. White 20
IMO Blue/Orange 20 Data ECM behind glove box, second connector from bottom. White 36
IMI Blue/Yellow 14 Data ECM behind glove box, second connector from bottom. White 36
Toyota FJ Cruiser (L Key) 2010-2014
12V Blue/Black 7 (+) Ignition Switch. White 8
Ignition 1 Black/Red 6 (+) Ignition Switch. White 8
Ignition 2 Blue/Yellow 4 (+) Ignition Switch. White 8
Accessory 1 White/Green 3 (+) Ignition Switch. White 8
Starter 1 Green/Black 8 (+) Ignition Switch. White 8
Starter 2 Black/White 1 (+) Ignition Switch. White 8
CAN H Pink 6 Data OBDII. White 16
CAN L Violet 14 Data OBDII. White 16
Parking Lights Green 14 (-) Headlight Switch. Black 17
Autolights Blue 12 (-) Headlight Switch. Black 17
Security Light Violet/White 15 (+) A/C Amplifier behind radio. White 20
IMO Blue/Orange 20 Data ECM behind glove box, second connector from bottom. White 36
IMI Blue/Yellow 14 Data ECM behind glove box, second connector from bottom. White 36
Connector Information
Page 13
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Not required in D2D mode.
[1] (AC) Tach Input(-) Trunk Status Input(-) Door Status Input
(-) E-Brake Status Input
Rem
ote
Sta
rter
(-) GWR (Status)
(-) Unlock Output
(-) Trunk Release Output [2]
(-) Lock Output [2]
(+) 12V
(-) Hood Status Input
(-) Ground
(+) Brake Input
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(-) E-Brake Status Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
IMI Data: Yellow/Black: 10
IMI Interrupt (conn. side): Orange/Red: 10
IMO Data: Orange/Black: 11
IMI Interrupt (vehicle side): Yellow/Red: 11
(-) Hood Status Output: Blue/Red: 12
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
(+) 12V: Red: 13(+) 12V
(-) Ground (-) Ground: Black: 14
If the module programs but the vehicle starts and stops after remote starting, reverse IMI wires.
Yellow/Black and Yellow/Red wires needs to be on the ECM side.
Autolight Off: Orange/Yellow: 9
Autolight Off: Yellow: 8
(+) Ignition 1 Output
(+) Ignition 2 Output
(+) Accessory Output
Passenger Fuse Box(White 1-pin conn.)
1
(+) Ignition 2: Yellow, pin 35 (+) Ignition 1: Lt Green, pin 34
(+) 12V: Black, pin 1
[2] (-) Unlock: Gray, pin 19
[2] (-) Trunk Release: Red, pin 5
[2] (-) Lock: Black, pin 10
Junction Connector
(White conn. passenger kick panel)
IMI: Tan, pin 12
IMO: Greenpin 11
Junction Connector(White conn. driver kick panel)
Trunk release switch(White conn. at release switch)
16 4 3 25
12345678910
1112131415161720 19
(-) Parking Lights: Blue, pin 18
Headlight Switch(White conn. at
Headlights switch)
18
(-) Parking Lights Output
(-) Autolight:Orange,pin 19
Diagnosticconnector OBDII
(connector side view)
1 8
169
CAN High: Pink, pin 6
CAN Low: Tan, pin 14
(+) Starter 1 Output
(+) Starter 2 Output
Power ECU(White conn. behind glove box)
(+) Starter 1: Black, pin 17
(+) Starter 2: Lt Blue, pin 1519
2610
3240 1817 1115
3435
Accessory 1: Red, pin 11
10 9 8 7 6 5 4 3 2 111
1918 17 16 15 1413 1220
8 7 6 5 4 3 1210 9
17 16 15 14 13 111218
[2] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
XKD2D65TX
(-) Ground
RX(+)12V
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side.
10
4
14
12
2
DBALL2
RF
Prog. Button
LED
Installation Type 6
Cut
[3] This connection is ONLY required if the security light in the vehicle is ON following its remote start. Not required on all vehicles.
Page 14
Autolights connection on required in vehicles with autolights.
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
Type 6 - Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
Toyota Avalon (Smart Key) 2011-2012
12V Black 1 (+) Dash Fuse box. White 1
CAN H Pink 6 Data OBDII. White 16
CAN L Tan 14 Data OBDII. White 16
IMO Green 11 Data Behind Glove Box. White 18
IMI Tan 12 Data Behind Glove Box. White 18
Parking Lights Blue 18 (-) Headlight Switch. White 20
Autolights Orange 19 (-) Headlight Switch. White 20
Ignition 1 Yellow 35 (+) Power Source Control ECU behind glove box. White 40
Ignition 2 Lt. Green 34 (+) Power Source Control ECU behind glove box. White 40
Accessory 1 Red 11 (+) Power Source Control ECU behind glove box. White 40
Starter 1 Black 17 (+) Power Source Control ECU behind glove box. White 40
Starter 2 Lt. Blue 15 (+) Power Source Control ECU behind glove box. White 40
Lock Black 10 (-) Driver Kick Panel. White 20
Connector Information
Page 15
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Module ProgrammingPage 16
Important
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
rd3
10-pinD2D
st1
th4
12-pin14-pin
nd2
rd3
1
If with Key:Insert the key, turn ignition ON, LED should start flashing green after ~ 5 seconds.
& &&Flashes Flashes
Key IN OF
F
START
IGN
2 Start the vehicle.Apply brakes and press PTS button once; to start the car.
Key IN OF
F
START
IGN
3
The LED will turn ON solid for 3 seconds:§ Orange: Bypass successfully programmed
WITHOUT statuses.§ Green: Bypass successfully programmed WITH
statuses.
The LED will turn ON solid for 3 seconds:§ Orange: Bypass successfully programmed
WITHOUT statuses.§ Green: Bypass successfully programmed WITH
statuses.Then Press PTS button once to shut down the vehicle.
& &OR ORSolid Orange
x3 SecsSolid Orange
x3 SecsSolid Green
x3 SecsSolid Green
x3 Secs
Key OUT OF
F
START
IGN
If with PTS (Push-to-Start):With the key inside the vehicle, push PTS button 2 times without applying brakes to turn ignition ON.
or
or
or
2XENGINESTARTSTOP
PUSH
1XENGINESTARTSTOP
PUSH
1XENGINESTARTSTOP
PUSH
Do NOT press brake pedal
You have successfully completed the module programming sequence.
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Flash Standard install, and follow the instructions provided on the screen.5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Module Reset
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Page 17
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Page 18
To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly
the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
Feature ProgrammingProgramming
Button
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
* Default Option
Feat. Operation Flashes/Options Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
RFTD Output
Type1
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Page 19
LED Description Troubleshooting
Module has no power.
Make sure the D2D harness is connected or that the 12
Volt is present between the red and black wires. If the
12 Volt is present, the module may be defective.
Waiting to begin the programming sequence.Ensure the correct programming procedure is being
followed.
Initialization failed.Reset the module and complete the programming again.
If the issue persists, please contact Technical Support.
Transponder functions were skipped.
(If compatible) when RXT mode is not desired or
convenience features are needed, please reset and
reprogram the module.
All required CAN networks has been detected. Normal operation.
1 of 2 CAN networks has been detected. Normal operation
Key2GO initiated.Please follow the steps indicated in “Module
programming” to complete the Key2GO programming.
Module was successfully programmed with all functions. Normal operation
Module was successfully programmed without
transponder functions.Normal operation.
CAN2 not detected.
Check the CAN2 Orange/Green and Orange/Brown wire
connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not
require this connection, skip this step by pressing the
programming button 5 times.
J1850 not detected.Check the J1850 wire connection. Wake up the data bus
by turning the ignition on and try again.
CAN1 not detected.
Check the CAN1 Tan and Tan/Black wire connections.
Wake up the data bus by turning the ignition on and try
again. If your installation does not require this
connection, skip this step by pressing the programming
button 5 times.
Bypass data not detected.
Check the bypass line connection. If more than one wire
is used, make sure they are not inverted. Ensure the
vehicle still operates correctly using the factory key.
Bypass processing error.
The bypass calculation failed. Reset the module and try
again. If the condition persists, please contact Technical
Support.
ISO 1 not detected.
The Yellow/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
ISO 2 not detected.
The Orange/Black wire did not detect the expected
signal. Refer to "Installation (wiring diagrams & vehicle
wiring reference charts)" to check the connections.
MUX not detected.
The Violet/Green or Violet/Brown wire did not detect the
expected voltage value. Refer to "Installation (wiring
diagrams & vehicle wiring reference charts)" to check
the connections.
Module Programming
Module Programming - Error Codes
Solid red
Flashes redx 1
Flashes redx 1
Flashes redx 2
Flashes redx 3
Flashes redx 4
Flashes redx 5
Flashes redx 6
Flashes redx 7
Solid greenx 3 secs
Flashesgreen
Solid orange
Flashes red& green
Off
Flashesorange
Flashesorangeslowly
Solid orangex 3 secs
LED Diagnostics & Troubleshooting
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
LED Description Troubleshooting
OBDII feature is not supported.The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
Ground When Running (Status) command received. The module has initialized the remote start sequence.
Ignition ON command received.The module has received the Ignition ON command and
is processing the remote start sequence.
Start ON command received.The module has received the Start ON command and is
processing the remote start sequence.
PTS shutdown error.The PTS output from the module was not activated due
to safety protection.
CAN bus incorrectly detected.
Verify the CAN1 and CAN2 connections. Refer to
“Installation (wiring diagrams & vehicle wiring reference
charts)” to check the connections.
LOCK command received.
UNLOCK command received.
TRUNK command received.
AUX1 command received.
AUX2 command received.
AUX3 command received.
Takeover successful. Normal operation.
Runsafe was not disabled.No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
Brake was not detected.The brakes were not detected, which prevents the
system from shutting down the vehicle.
Smart key was not detected.The smart key was not detected, which prevents the
system from shutting down the vehicle.
Speed was detected.The vehicle was detected as moving, which prevents the
system from shutting it down.
External module synchronization
Commands
Activation Ground When Running (Status)
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Shutdown codes
(Flashes red,red thenorange) x 10
Flashes red& orange
Flashes redx 21
Flashes redx 2
Flashes redx 4
Flashes redx 10
Flashes redx 1
Flashes redx 3
Flashesgreen
Flashesgreenquickly
Flashesgreen x 1
Flashesorange x 1
Flashesorange x 2
Flashesorange x 3
Flashesorange x 5
Flashesorange x 4
Flashesorange x 6
Page 20
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Limited One Year Consumer WarrantyPage 21
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Rev.: 20170330
© 2017 Directed. All rights reserved.
Platform: DBALL2Firmware: TL4
310
1 2
12
11
12345678910
1112131415161720 1819
White 20-pin connector(at headlight switch)
1817
16151413
74 5 6
98
Wire jump template
Quick Reference Guide
© 2017 Directed. All rights reserved.
Vehicle Takeover
1
2
3
Stop the vehicle in a safe parking spot and put the gear in Park (P).
Press remote start
button*
* Your aftermarket remote may differ from the model shown in the illustrations.
Stop & put vehicle in Park (P)
P&
Flashes
ENGINESTARTSTOP&
HOLD
Exit vehicle with Smart Key
Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
It is now safe to leave the engine running and exit the vehicle with the factory remote in hand.
Press the button to remote start the vehicle.*
The PTS button will flash once to indicate the vehicle is now in Pit Stop Mode.
DBALL2-TL4
The vehicle takeover feature is not available in this firmware. The vehicle engine will shut down as soon as a door is opened.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution
Quick Reference Guide
© 2017 Directed. All rights reserved.
DBALL2-TL4
Notes
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution