No. 2014-024739-03(1/2)s kl ~~~~]I~AI~~

Korea Testing Laboratory

~ CZ.I ~ AiCertificate of Safety

Topworx Incorporated3300 Fern Valley Road, Louisville Kentucky 40213, United States of America

7l7e following product manufactured by the above company has been authorized for the use ofsafety certification mark as the prcxfuct has satisfied the safety and health requirements under Article34 of OCCUPATIONAL SAFElY AND HEALTH ACT and paragraph 4 of Article 58-4 of ENFORCEMENTORDINANCE OF the same ACT.

Electrical EquipnentProximity Switch with Connection Head

MadeJ (Marking) I Certificate No.10 Series GO Switch with Connection Head

(Ex de IIC T4/T6, Ex tb IIIC T130°C/T85°C IP66) / 14-KB'4BO-0484X

Applied slandardsAnnouncement No. 2013-54 of Ministry of Employment and Labor

Cordtions d certification1. Manufacturing location(s) : This certificate is only valid for the specified products

produced at 13300 Fern Valley Road, Louisville Kentucky 40213, United States of America'.

2. Description of equipment.70 Series GO Switch with Connection Head.

'Rating : 1.2 A at 40 VAC, 0.5 A at 125 VAC,

4 A at 120 VAC, 3 A at 120 VAC, 3 A at 24 VDC, 1 A at 24 VDC

-Ambient Temperature: -40 °c ~ Ta ~ +100 °C (tor T4, T130°C) / +50 °C (for T6, T85°C)

3. SCope of certification: This certificate is only valid for the model as above.

4. Special conditions for safe use'See the next page.

5. Details of certificate changes : None

6. Details of the others : Manufacturer shall take the responsibility including maintaining

quality requirements for the certified products, receiving factory surveillance and informing

any changes to the certified products.

Date of Issue: 2014-09-15

tt~t!~71~AI~'--'IJ4!1~'_l~--1lKOREA TESTING LABORAT~@)~===-_,..

FP251-8 152-718 Ai~AI T~T CIAI~~ 26~ 87(T~-S) http://www.ktl.re.kr426-910 ~71£ CC!~AI ~~T oHCC!~ 723(A~-S)

No. 2014-024739-03(2/2)s kl ~~tt~71~AI~~

Korea Testing Laboratory

Q)nditims of Qrtificatioo4. Special conditions for safe use

·The 70 Series GO Switch with Connection Head assembly shall be suitably earthed by itsinstallation via the male thread of the GO Switch body.

·00 not allow dust layers to build up on this product.

·AII terminal screws, used and unused, shall be fully tightened down by the end user.

·No more than one single or multi-stranded lead shall be connected to the terminal unless multipleconductors have been joined in a suitable manner, e.g. two conductors into a single insulatedbootlace ferrule, or any method indicated on the terminal certificate.

·AII terminals, and accessories such as cross-connectors, shall be installed in accordance with theterminal manufactures instructions. Topworx Incorporated will supply the relevant terminalmanufacturer's instructions with each assembly covered by this certificate.

·The maximum voltage and current shown on the rating label must not be exceeded.

'When connecting conductors of cross section below the maximum 2.5mm2 allowed for the terminalthen the maximum amps per pole must be reduced inline with the maximum amps permitted for aterminal equivalent to the conductor size fitted.

FP251-8 152-718 Ai~AI T£T CIAI~£ 26~ 87(T£-5) http://www.ktl.re.kr426-910 ~71£ ~~AI ~~T oH~£ 723(A~-5)