The information presented in this publication has beencarefully checked for reliability; however, noresponsibility is assumed for inaccuracies.Specifications are subject to change without notice.
Trademarks
IBM, PC/AT, and PC/XT are trademarks ofInternational Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
AMD is a trademark of Advanced Micro Devices Inc.
Cyrix is a trademark of Cyrix Corporation.
IDT is a trademark of Integrated Devices TechnologyCorporation.
AMI is a trademark of American Megatrends Inc.
MS-DOS and WINDOWS 95/98/NT are registeredtrademarks of Microsoft Corporation.
iiContentsChapter 1: Introduction ...................................................................... 2
Key Features ................................................................................... 3Unpacking the Mainboard & Static Electricity Precautions..... 5
Chapter 2: Hardware Configuration ................................................ 6Mainboard Component Locations ............................................... 7Connectors....................................................................................... 8
PWR1 Ð AT Power Supply Connectors ............................... 8COM1/2 Ð Serial Port #1/#2................................................. 8PRN1 Ð Parallel Port ............................................................... 8FDC Ð Floppy Disk Port ......................................................... 8IDE1/IDE2 Ð Primary/Secondary IDE Ports...................... 8KBD Ð Keyboard Connector .................................................. 8JP4 Ð VGA Connector ............................................................. 8FAN1 Ð FAN Power Connector ............................................ 8J3 Ð ATX Form Card Connector ............................................ 8J8 (2, 4, 6, 8, 10) (KBLOCK) Ð Keylock & Power LEDConnector ................................................................................. 9J8 (1, 3, 5, 7) (SPK) Ð Speaker Connector.............................. 9J8 (13, 14) (TB-LED) Ð Turbo LED Connector ..................... 9J8 (15, 16) (HDD-LED) Ð HDD LED Connector .................. 9J8 (17, 18) (RST) Ð Reset Switch Connector ....................... 10J8 (19, 20)(PWBT) Ð ATX Power Button ............................. 10Sound Pro Connectors: ......................................................... 10CD1/CD2 Ð Analog Audio for Sony/Panasonic ............. 10J1 Ð Sound and Game ........................................................... 10J5 Ð Digital Audio IN ............................................................ 10J4 Ð Digital Audio OUT ........................................................ 11
Jumper Settings ............................................................................ 11JP2 Ð DIMM Voltage Selectors ............................................ 11JP6 Ð CMOS RAM Clear Selector........................................ 11JP9 Ð Onboard Sound Selector ............................................ 12J2 Ð Microphone Type Selector ........................................... 12
Memory Installation..................................................................... 12
iiiChapter 3: ACPI Functions & Connectors with ATX Power..... 13
PWR2 Ð ATX Power Connector .......................................... 13Software Power-Off .............................................................. 14Modem Ring Power-On ....................................................... 14Alarm Wake Up .................................................................... 14J8 (19, 20) (PWBT) Ð ATX Power Button and SuspendSwitch Connector .................................................................. 15
Chapter 4: BIOS Setup ..................................................................... 16Entering BIOS Setup .................................................................... 17Default ........................................................................................... 18
Load Optimal Settings ......................................................... 18Load Best Performance Settings ......................................... 18
Setup Items.................................................................................... 18Standard CMOS Setup ......................................................... 18Advanced CMOS Setup ....................................................... 19Advanced Chipset Setup ..................................................... 21Power Management Setup................................................... 23PCI/Plug and Play Setup..................................................... 25Peripheral Setup.................................................................... 26CPU Plug and Play Setup .................................................... 28Change Supervisor Password ............................................. 28Auto-Detect Hard Disks....................................................... 29Save Settings and Exit .......................................................... 29Exit Without Saving.............................................................. 29
Chapter 1Introduction
This mainboard is a high-performance mainboardbased on the advanced Pentiumª microprocessor,100MHz CPU external clock speed capability feature,and PCI Local Bus and the high-end AGP chipset. Themainboard offers a high degree of flexibility inconfiguration and is fully IBM PC/AT compatible.
Introduction 3
Key Features
The advanced features of this mainboard include:¥ Supports P54C/P55C Pentiumª (MMX) CPUs and
Cyrix/IBM 6x86L/6x86MX/MII, AMD K6/K6-2(3.2V & 2.2V), IDT C6 90~350MHz CPUs withFrequency at 60/66/75/83/100 MHz;
¥ Provides two SIMMs and two DIMMs forSDRAM/EDO/FPM memory modules, memoryexpandable up to 384MB, however, it is notrecommended to use EDO/FPM DRAM when83/100MHz CPU frequency is being used andSDRAM has to meet the requirement of PC-100 ifusing 100MHz;
¥ Supports 64M-bit (8Mx8, 4Mx16) EDO DRAM/SDRAM;
¥ Onboard 1MB Pipeline Burst synchronous L2cache;
¥ Built in high performance 64bit 3D AGP GraphicsAccelerator with 8MB frame buffer;
¥ Provides both ATX/AT power connector, andsupports various ATX power functions, such as:Modem Ring On, ATX Power Button, SuspendSwitch, and Alarm Wake Up;
¥ Supports ACPI and Legacy PMU, and the UltraDMA/33, fully compliant to PC97 & PC98;
¥ Provides 3 PCI Bus slots, 2 ISA Bus slots and PCIBus Master IDE interface with 2 connectors whichsupports 4 IDE devices in 2 channels;
¥ Super Multi-I/O chip supports 2 serial ports with16550 compatible fast UART, 1 parallel port withEPP and ECP capabilities, and one floppy diskdrive interface with 1Mb/s transfer rate;
4 Chapter 1
¥ Provides ATX Form Card containing PS/2 Mouse,2 USB interface, and Infrared connectors;
¥ Onboard 3D Sound Pro meets PC98' SPEC and supportHRTF Positional Audio, Direct Sound 3D provide driversfor 3D games that use Aureal software interface, Software Wave-table Synthesizer, and Digital Audio Interface (SPDIF) IN/OUT;
¥ Bundled PC-cillin (OEM) provides automaticvirus protection for Window95/98 and the Internet.
Introduction 5
Unpacking the Mainboard & StaticElectricity Precautions
This Mainboard package contains the following items:
1. This Mainboard and a Device Driver
2. This UserÕs Guide and AT cable set
3. Sound & Game ribbon cables/bracket andSPDIF/IN cable
4. ATX Form Card and VGA cable/bracket
The mainboard is easily damaged by static electricity.Follow the precautions below while unpacking orinstalling the mainboard.
1. Do not remove the mainboard from its originalpackage until you are ready to install it.
2. Frequently ground yourself to discharge any staticelectric charge that may build up in your bodywhile working on installation and/orconfiguration. For example, you may groundyourself by grasping an unpainted portion of thesystemÕs metal chassis.
3. Remove the mainboard from its anti-staticpackaging and place it on a grounded surface,component side up.
4. Handle the mainboard by its edges or by themounting bracket to avoid touching itscomponents.
5. Check the mainboard for damage. If any integratedcircuit appears loose, press carefully to seat itfirmly in its socket.
6. Do not apply power if the mainboard appearsdamaged. If there is damage to the board contactyour dealer immediately.
Chapter 2Hardware Configuration
Before you install this mainboard into the systemchassis, you may find it convenient to first configurethe mainboardÕs hardware. This chapter describes howto set jumpers and install memory modules, and whereto attach components.
Hardware Configuration 7
Mainboard Component Locations
PCI3 PCI2 PCI1
SIMM2SIMM1
DIMM2DIMM1
COM2
Socket 7
PWR1
KBD
12
COM112
FDC1
J3
10 1
18 9
IDE21
IDE11
3
1
HDD-LED
SPK RST
PWBT
J81
TB-LED
Keylock
Cache
Cache
BIO
S
Ch
ipset
1CD1CD2
JP2
PRN11
219
20
I/O
So
un
dP
ro
J2
J4
PWR2
5V
3.3V
J5
VG
A C
hip
1
JP6
1
FAN1
VD
RA
M
VD
RA
M
VD
RA
M
VD
RA
M
Ch
ipset
J1
JP4 1
JP9
Figure 2-1. Mainboard Component Locations
8 Chapter 2
Connectors
Attach system components and case devices to themainboard via the mainboard connectors. A descriptionof each connector follows. See Figure 2Ð1 for thelocation of the connectors on the mainboard.
Note: Make sure that the power is turned off beforemaking any connection to the board.
PWR1 – AT Power Supply ConnectorsCOM1/2 – Serial Port #1/#2PRN1 – Parallel PortFDC – Floppy Disk PortIDE1/IDE2 – Primary/Secondary IDE PortsKBD – Keyboard ConnectorJP4 – VGA ConnectorFAN1 – FAN Power Connector
J3 – ATX Form Card Connector
This connector contains 2 sets of USB interface, PS/2Mouse, and Infrared connectors. Connect the ATXForm Card cable to this connector.
Hardware Configuration 9
J8 (2, 4, 6, 8, 10) (KBLOCK) – Keylock &Power LED Connector
Pin Description
2 LED Output4 N.C.6 Ground8 Keylock
10 Ground
J8 (1, 3, 5, 7) (SPK) – Speaker Connector
Pin Description
1 Data Out3 N.C.5 Ground7 +5V
J8 (13, 14) (TB-LED) – Turbo LEDConnector
Pin Description
13 (+) +5V14 (Ð) Active Low
J8 (15, 16) (HDD-LED) – HDD LEDConnector
Pin Description
+ +5VÐ Active Low
10 Chapter 2
J8 (17, 18) (RST) – Reset Switch Connector
Setting Description
Open Normal ModeClose Reset System
J8 (19, 20)(PWBT) – ATX Power Button
Refer to Chapter 3.
Sound Pro Connectors:
CD1/CD2 – Analog Audio forSony/Panasonic
Connect to ÒAUDIOÓ on the CD-ROM drive, and thesignal for Panasonic jack is G-S-G-S and S-G-G-S forSony.
J1 – Sound and Game
Sound contains Line-in/MIC (Microphone), and Line-out (Speaker). Game connector is also the Joysticconnector. Connect this connector to the Sound &Game ribbon cable/bracket as the following drawing:
J1J1
Line-In MIC GameLine-Out
J5 – Digital Audio IN
Depending on the type of your CD-ROM drive toconnect this connector to ÒDIGITAL AUDIOÓ on theCD-ROM drive by using SPDIF/IN cable.
Hardware Configuration 11
J4 – Digital Audio OUT
Connect to the Digital Audio device (the AudioAmplifier or Minidisk) by using optional SPDIF/OUTcable/bracket.
Jumper Settings
JP2 – DIMM Voltage Selectors
5V
Voltage Setting
3.3V
5V
3V
5V
3V
JP6 – CMOS RAM Clear Selector
Description Setting
Normal Mode3
1
Clear CMOS3
1
Note: 1. Make sure that this jumper is set to Normal Modebefore installing the mainboard and the power isoff before clearing the CMOS.
2. If using the ATX power, you need to unplug thepower cable and then plug the cable back on afterclearing the CMOS.
12 Chapter 2
JP9 – Onboard SoundSelector
Enabled
Description Setting
Disabled
J2 – Microphone TypeSelector
Special Mode
Description Setting
Normal Mode(default)
Memory Installation
The mainboard lets you add up to 384MB of systemmemory through SIMM and DIMM sockets on theboard. Two SIMM sockets and two 168-pin DIMMsockets are divided into three banks: Bank 0, Bank 1,and Bank 2. The mainboard supports the followingmemory configurations.
Bank Memory ModuleBank 0DIMM1
4MB, 8MB, 16MB, 32MB, 64MB, 128MB, 256MB
Bank 1DIMM2 4MB, 8MB, 16MB, 32MB, 64MB, 128MB, 256MB
Bank 2SIMM1 & SIMM2 2 x 4MB/8MB/16MB/32MB/64MB/128MB
Total System Memory = Bank 0 + Bank 1 + Bank 2Notes: 1. The speed of SDRAM DIMM modules have to be faster than
12ns (Ò-12Ó parts). When 100MHz clock speed is beingused, then the speed of SDRAM DIMM should meet thePC100 SDRAM specification (8ns or Ò-8Ó SDRAM atleast).
2. The speed of EDO/FPM DRAM have to be faster than 70ns,but it is not recommended for the performance purpose of thesystem.
Chapter 3ACPI Functions & Connectors
with ATX Power
PWR2 – ATX Power Connector
The ATX power supply provides a single 20-pinconnector and supports the ACPI specification.
Pin Description Pin Description
1 3.3V 11 3.3V2 3.3V 12 Ð12V3 Ground 13 Ground4 +5V 14 PS-ON5 Ground 15 Ground6 +5V 16 Ground7 Ground 17 Ground8 Power OK 18 Ð5V9 5VSB 19 +5V10 +12V 20 +5V
14 Chapter 3
The functions and connectors described below workwith the ATX power supply.
Software Power-Off
Follow the steps below to use the ÒSoftware Power-OffControlÓ function in Windows 95 with ATX powersupply.
1. Click the START button on the Windows 95 taskbar.
2. Select Shut Down The Computer to turn off thecomputer. The message ÒIt is now safe to turn offyour computer.Ó will not be shown when using thisfunction.
Modem Ring Power-On
While in Soft-off/Suspend state, if an external modemring-up signal occurs, the system wakes up and can beremotely accessed. Make sure that the Ring ResumeFrom Soft Off option is set to Enabled in the BIOS setupsection (Refer to the Power Management section inChapter 4.)
Alarm Wake Up
If you want to autoboot the system at a certain time, setthe function of RTC Alarm time properly and thefunction of RTC Alarm Resume From Soft Off option inthe BIOS Setup section will be set to Enabled.
ATX Functions & Connectors 15
J8 (19, 20) (PWBT) – ATX Power Button and SuspendSwitch Connector
Attach the ATX Power Button or Suspend Switch cableto this connector.
In the AT power system, this connector will act as asuspend switch; and in the ATX power system, thisconnector will be not only an ATX power button but aSuspend switch as well. Details are described below:
When the system is off, push the power button to turnthe system on. When the system is on, push the powerbutton rapidly to switch the system to the Suspendmode, and, by pushing and holding the button formore than 4 seconds, it will turn the system completelyoff. When the system is in the Suspend mode, push thepower button rapidly to turn the system on.
Chapter 4BIOS Setup
This chapter explains how to configure the mainboardÕsBIOS setup program. The setup program providedwith the mainboard is the BIOS from AMI.
After you have configured the mainboard and haveassembled the components, turn on the computer andrun the software setup to ensure that the systeminformation is correct.
The software setup of the system board is achievedthrough Basic Input-Output System (BIOS)programming. You use the BIOS setup program to tellthe operating system what type of devices areconnected to your system board.
The system setup is also called CMOS setup. Normally,you need to run system setup if either the hardware isnot identical with information contained in the CMOSRAM, or if the CMOS RAM has lost power.
Note: When installing newer BIOS into thismainboard, you need to clear CMOS for amoment then set back to Normal Mode or holddown the <End> key then power on to rebootthe system.
BIOS Setup 17
Entering BIOS Setup
To enter the BIOS Setup program:
1. Turn on or reboot the system. A screen appearswith a series of diagnostic checks.
2. When ÒHit <DEL> if you want to run SETUPÓappears, press the <DEL> key to enter the BIOSsetup program. The following screen appears:
Standard CMOS setup for changing time, date, hard disk type, etc.
AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.1X(C)1998 American megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced CMOS Setup
Advanced Chipset Setup
Power Management Setup
PCI/Plug and Play Setup
Load Optimal Settings
Load Best Performance Settings
Peripheral Setup
CPU Plug and Play Setup
Change Supervisor Password
Auto-Detect Hard Disks
Save Settings and Exit
Exit Without Saving
Esc: Quit ↑ ↓ → ←: Select Item (Shift) F2: Change Color F5: Old ValuesF6: Optimal values F7: Best performance values F10 : Save&Exit
3. Use your keyboard to choose options. Modifysystem parameters to reflect system options. PressAlt-H for Help.
18 Chapter 4
Default
Every option in the BIOS Setup contains two defaultvalues: Best default and the Optimal default value.
Load Optimal Settings
The Optimal default values provide optimum systemsettings for all devices and system features.
Load Best Performance Settings
The Best default values provide best performancesettings for all devices and system features, howeverdepending on the devices used, these settings are notrecommend for long hours of work load.
Setup Items
Standard CMOS Setup
Choosing the item from the BIOS Setup main menu.All Standard Setup options are described in thissection.
Date/Time Select the Date/Time option to change the dateor time. The current date and time aredisplayed. Enter new values through thedisplayed window.
BIOS Setup 19Pri MasterPri SlaveSec MasterSec Slave
Choose these options to configure the harddisk drive named in the option. When youclick on an icon, the following parameters arelisted: Type, LBA/Large Mode, Block Mode,32Bit Mode, and PIO Mode. All parametersrelate to IDE drives except Type.
Floppy DriveA, B
Choose the Floppy Drive A or B option tospecify the floppy drive type. The settings are360KB 51/4", 1.2MB 51/4", 720KB 31/2", 1.44MB31/2", or 2.88MB 31/2".
Advanced CMOS Setup
Choose the Advanced item from the BIOS Setup mainmenu. All Advanced Setup options are described inthis section.
1st Boot Device2nd Boot Device3rd Boot Device4th Boot Device
Set these options to select the bootsequence from different booting devices.
Try Other BootDevices
Set this option to enable other bootingdevices.
S.M.A.R.T for HardDisks
Select this option to enable or disable theS.M.A.R.T. function of HDDs.
Quick Boot Set this option to Enabled to permit BIOS toboot within 5 seconds.
Boot Up Num-Lock When this option is set to On, BIOS turnsoff the Num Lock key when the system ispowered on so the end user can use thearrow keys on both the numeric keypadand the keyboard.
20 Chapter 4Floppy Drive Swap Set this option to Enabled to specify that
floppy drives A: and B: are swapped.
Floppy Drive Seek Set this option Disabled to provide a fasterboot and reduce the possibility ofdamaging the heads.
PS/2 MouseSupport
When this option is set to Enabled, BIOSsupports a PS/2-type mouse.
Password Check This option specifies the type of BIOSpassword protection that is implemented.The settings are:Setup: The password prompt appears
only when an end user attemptsto run BIOS Setup.
Always: A password prompt appearsevery time the computer ispowered on or rebooted.
The BIOS password does not have to beenabled. The end user sets the passwordby choosing the Password icon on theBIOS Setup screen.
Boot to OS/2 Select this option to boot to OS/2 system.
Internal Cache Select this option to enable the internalcache.
External Cache Select this option to enable External Cache.
System BIOSCacheable
BIOS always copies the system BIOS fromROM to RAM for faster execution. Set thisoption to Enabled to permit the contents ofthe F0000h RAM memory segment to bewritten to and read from cache memory.
BIOS Setup 21C000, 16K Shadow;C400, 16K Shadow;C800, 16K Shadow;CC00, 16K Shadow;D000, 16K Shadow;D400, 16K Shadow;D800, 16K Shadow;DC00, 16K Shadow
Disabled: The specified ROM is notcopied to RAM.
Enabled: The contents of the ROM areaare not only copied from ROMto RAM for faster execution, thecontents of the RAM area canbe written to or read from cachememory.
Cached: The contents of the ROM areaare copied from ROM to RAMfor faster execution.
Advanced Chipset Setup
Choose the Chipset item from the BIOS Setup mainmenu. All Chipset Setup options are then displayedand are described in the following section:
DRAM AutoConfiguration
Set this option to enable the AutoConfiguration of DRAM Timing andRefresh Cycle Time.
EDO/FPM Speed;SDRAM Speed
Set these options to select the properDRAM speed.
RAS forEDO/FPM/SDRAM
This option is used to select a properDRAM RAS Pulse width.
RAS PrechargeTime
This option is used to select a proper RASPrecharge timing.
SDRAM ReadTiming
This option is used to select a properSDRAM Back to Back read timing.
Refresh QueueDepth
This option is used to select a properRefresh Queue Depth.
22 Chapter 4SDRAM CASLatency
This option is used to select a properSDRAM CAS Latency.
ISA Bus Clock Set this option to select the proper ISA busclock.
8-Bit I/O RecoveryTime
This option specifies the length of a delayinserted between consecutive 8-bit I/Ooperations.
16-Bit I/O RecoveryTime
This option specifies the length of a delayinserted between consecutive 16-bit I/Ooperations.
Graphic WindowSize
This option is used to select a properGraphic Window size.
OnBoard USB Set this option to Enabled to enable thesystem BIOS USB (Universal Serial Bus)functions.
USB function forDOS
Set this option to Enabled to enable passiverelease on the universal serial bus.
BIOS Setup 23
Power Management Setup
The BIOS Setup options described in this section areselected by choosing the Power Management Setupfrom the BIOS Setup main menu.
PowerManagement/APM
Set this option to enable power managementfeatures and APM (Advanced PowerManagement).
Green MonitorPower State
This option specifies the power state that thegreen PC-compliant video monitor enterswhen BIOS places it in a power savings stateafter the specified period of display inactivityhas expired.
Video PowerDown Mode
This option specifies the power conservingstate that the VESA VGA video subsystementers after the specified period of displayinactivity has expired.
Hard Disk PowerDown Mode
This option specifies the power conservingstate that the hard disk drive enters after thespecified period of hard drive inactivity hasexpired.
Standby Time out This option specified the length of systeminactivity while in Full power on state. Whenthis length of time expires, the computerenters Standby power state.
Suspend Time out This option specified the length of a period ofsystem inactivity while in Standby state.When this length of time expires, thecomputer enters Suspend power state.
24 Chapter 4Slow Clock Ratio This option specified the speed at which the
system clock runs in power saving states. Thesettings are expressed as a ratio between thenormal CPU clock speed and the CPU clockspeed when the computer is in the power-conserving state.
Primary IDE;Secondary IDE;Serial Port1;Serial Port2;Parallel Port;IRQ 0, 1, 3-15/NMI;Ring In;Display Activity;Sound Blaster Port(220h);PCI/AGP/IDEMaster;Floppy Port
When set to Yes, these options enable eventmonitoring on the specified hardwareinterrupt request line and the computer is in apower saving state, BIOS watches for activityon the specified IRQ line. The system entersthe full power on state if any activity occurs.
RTC Alarm PowerOn
Set this option to enable the RTC Alarm towake up the system which is Soft Off.
RTC AlarmMonth;RTC Alarm Date;RTC Alarm Hour;RTC AlarmMinute;RTC AlarmSecond
Set these options to specify the RTC Alarmtime on Month/Date/Hour/Minute/Second.
BIOS Setup 25
PCI/Plug and Play Setup
Choose the PCI/PnP item from the BIOS Setup mainmenu.
Plug and PlayAware OS
Set this option to Yes if the operation systemin this computer is aware of and follows thePlug and Play specification. Currently, onlyWindows 95 is PnP-aware.
PCI VGA PaletteSnoop
When this option is set to Enabled, multipleVGA devices operating on different buses canhandle data from the CPU on each set ofpalette registers on every video device. Bit 5of the command register in the PCI deviceconfiguration space is the VGA Palette Snoopbit (0 is disabled).
OffBoard PCI IDECard
This option specifies if an offboard PCI IDEcontroller adapter card is installed in thecomputer. You must specify the PCIexpansion slot on the motherboard where theoffboard PCI IDE controller is installed. If anoffboard PCI IDE controller is used, theonboard IDE controller is automaticallydisabled. If an offboard PCI IDE controlleradapter card is installed in the computer, youmust also set the Offboard PCI IDE PrimaryIRQ and Offboard PCI IDE Secondary IRQoptions.
Pri. OffBoard PCIIDE IRQ;Sec. OffBoard PCIIDE IRQ
These options specify the PCI interrupt usedby the Primary (or secondary) IDE channel onthe offboard PCI IDE controller.
Assign IRQ to PCIVGA
Set this option to Enabled to assign IRQ to PCIVGA Card.
26 Chapter 4
PCI Slot 1/2/3 IRQPriority
These options specify the priority IRQ to beused for any PCI devices installed in PCIexpansion slots 1 through 4.
DMA Channel 0,1, 3, 5, 6, 7
These options specify the bus that thespecified DMA channel is used on.
IRQ3, 4, 5, 7, 9, 10,11, 14, 15
These options specify the bus that thespecified IRQ line is used on. These optionsallow you to reserve IRQs for legacy ISAadapter cards.
Reserved MemorySize;Reserved MemoryAddress
Set these options to select reserved memoryand started address for the IO card.
Peripheral Setup
Choose the Peripheral item from the BIOS Setup mainmenu.
OnBoard FDC This option enables the FDC (Floppy DriveController) on the motherboard.
OnBoard SerialPort1
This option specifies the base I/O portaddress of serial port 1.
OnBoard SerialPor2
This option specifies the base I/O portaddress of serial port 2.
BIOS Setup 27OnBoard IR Port This option specifies the serial port2 for IR
port.Disabled: The normal serial port mode is
being used.HPSIR/ASKIR: The serial port2 will be
redirected to support IR functionwhen this option is set to HPSIR orASKIR.
IR Duplex Set this option to select Full or Half Duplexmode for IR port.
OnBoard ParallelPort
Set this option to specify the base IO addressfor parallel port.
Parallel Port Mode Depends on the type of your external devicewhich connects to parallel port to chooseNormal, EPP, or ECP mode.
Parallel Port IRQ This option specifies IRQ to parallel port.
Parallel Port DMAChannel
This option is only available if the setting ofthe Parallel Port Mode is ECP.
OnBoard IDE This option specifies the channel used by theIDE controller on the motherboard.
Primary Master/Slave Prefetch;Secondary Master/Slave Prefetch
Set these four options to enable prefetchmode for four IDE devices.
OnBoard SoundPRO
Set this option to enable the Sound Profunctions.
28 Chapter 4
CPU Plug and Play Setup
CPU Plug andPlay
Set this option to specify the CPU PnP byAuto or User Define.
CPU Brand The CPU Brand is detected by BIOS ,therefore, this option can not be changed bythe user (display only).
VCCore Voltage Set this option to select CPU core voltagewhen CPU Plug and Play option is set to UserDefine.
CPU Speed Select a correct CPU speed to match yourCPU when CPU Plug and Play option is set toAuto.
CPU BaseFrequency
Set this option to select CPU Frequency whenCPU Plug and Play option is set to UserDefine.
CPU MultipleFactor
Set this option to select CPU Multiplier whenCPU Plug and Play option is set to UserDefine.
Change Supervisor Password
This item lets you configure the system passwordwhich is required every time when the system boots upor an attempt is made to enter the Setup program. Thepassword cannot be longer than six characters.
Note: Keep a safe record of the new password. If youforget or lose the password, the only way toaccess the system is to clear CMOS memory .
BIOS Setup 29
Auto-Detect Hard Disks
If your system has an IDE hard drive, you can use thisutility to detect its parameters and automatically enterthem into the Standard CMOS Setup. This utility willautodetect up to four IDE devices.
Save Settings and Exit
Select this item to save the values entered during thecurrent session and then exit the BIOS setup program.
Exit Without Saving
Select this item to exit the BIOS setup program withoutsaving the values which has been entered during thecurrent session.