Compression Installation & Service
What (Company Name) Can Do For Your BusinessTailored to clients’ needs, we provide a full range of compression
maintenance and innovation from install too service.
Installations
CapabilitiesGas Processing & Compression
• Compressor Installation
Compressor Station Installations
Compressor Valve Maintenance• The purpose of the valves in a reciprocating compressor is to let air in
and out of the cylinder during the compression process. These valves are considered automatic because they are operated by the difference in pressure across the valves. The key to long valve life is to have positive action of the sealing components with minimum resistance. Compressor valves serves as check valves for the inlet and discharge passages of the cylinder and will open and close once for every revolution of the crankshaft. If the compressor is running at 500 rpm for 24 hours a day, the valves will open and close 720,000 times every day!
Valve Port Inspection• If there is a backflow of gas, it will cause an increase in the
temperature of the valve, valve covers and the cylinder body. The increase in temperature could also be caused by prolonged unloaded operation of the cylinders.• Valve ports should be inspected for cracks through the use of a dye
penetrant. You should also be checking the seating surface for the valve body for nicks, pitting, or grooving which can prevent the proper sealing of the valve body to the cylinder. If you have a cylinder that uses jam screws to hold the valve in the valve port, any damage done to the seating surface may be corrected by re-facing the seat
Compressor Maintenance & Repair
• From Small Compressor Packages To Large Our Company Provides Reliability
Gas Packing and Packing Cases• The packing is a crucial component because it provides the seal between
the piston rod and the cylinder. The packing is made up of a series of cups each of which houses several rings. The intermediate cup is what allows the oil to enter the box through an axial hole. Any gas that has leaked out of the box is able to be recovered and recycled (if there is a low pressure collection system) or could be sent to a flare or other treatment process.• The inspection of the gas packing involves an assessment on whether or
not there is a leak. A packing that is properly seated on a rod that is running true should not be exhibiting any leakage. With a periodic subjective inspection of the compressor, you will be able to see indications if the performance of the packing has deteriorated.
Compressor Packing Case Repair
Compressor Packing
Parts AvailabilityFrom Compressor Frame to
Cylinder Head
Cylinder Taper Tolerance• The taper in the compressor cylinder is what causes the rings to travel
in and out of their grooves as the piston is traveling up and down the cylinder.• Cylinder taper is the change in the cylinder diameter versus the length
of the bore. You should inspect the cylinders with a micrometer on a periodic basis to determine the taper or the diametrical wear.
Compressor Cylinder Inspection & Boring
Importance of Motor Shaft Alignments
• The objective of optimized shaft alignment is to increase the operating life span of rotating machinery. To achieve this goal, components that are the most likely to fail must be made to operate within their acceptable design limits. • While misalignment has no measurable effect on motor efficiency, correct
shaft alignment ensures the smooth, efficient transmission of power from the motor to the driven equipment. Incorrect alignment occurs when the centerlines of the motor and the driven equipment shafts are not in line with each other. Misalignment produces excessive vibration, noise, coupling and bearing temperature increases, and premature bearing or coupling failure.
Shaft Alignments
Shaft Alignments / Laser
Laser Alignments
Shaft Alignments / Dial Indicator
Compressor Parts Inspection
Compressor Parts Inspection
Compressor Valve Inspections
Compressor Valve Reconditioning
Compressor Part Inspection
Compressor Part InspectionsChecking Connecting Rod For
Straigthness
Compressor Part InspectionsOil Pump Clearance Inspection
Crankshaft Web Deflection Inspection
Crankshaft Web Deflection Inspection Is Crucial For
Longevity
Bearing Inspections & Bump Checks Are Crucial For Compressor Reliability