Chapter 7 Additional Problems
Chapter 7 Additional Problems
X7.1 A three-phase, 1200 HP, 2300 V, 60 Hz, RR synchronous machine has and . When operated with the mechanical load disconnected with rated voltage and frequency, the field current is adjusted until line current has a minimum value. At this point, , the measured input power is , and the measured field circuit values are and . (a) Determine the rotational losses (core losses plus friction and windage) for this machine. (b) If the field current, frequency, and impressed terminal voltage are unchanged, but a mechanical load requiring 600 HP is attached, predict the power factor, line current, and efficiency.
(a) Using the no-load data,
(b) Since the no-load current was a minimum value, the machine was operating at unity power factor. The excitation voltage corresponding to can be determined.
Since , little error is introduced if is neglected in calculation of the torque for the loaded condition. From energy balance,
or
Based on [7.36],
Hence,
The losses are
X7.2 If the synchronous motor of Problem X7.1 still operates the 600 HP load with terminal voltage and frequency unchanged, but the field current is increased to 80 A, predict (a)the input power factor and (b) the leading VARs supplied to the three-phase grid. Assume that core losses (lumped with friction and windage losses) of Problem X7.1 are valid.
(a) For the new field current, the excitation voltage is
Assuming negligible,
(b)
X7.3 If the synchronous motor of Problem X7.1 now supplies rated power to a coupled mechanical load with rated voltage and frequency applied to the stator and , calculate (a) line current and (b) efficiency. Assume that can be neglected in torque angle determination. Also, assume that core losses have changed negligibly from Problem X7.1.
(a) The excitation voltage for is determined in Problem X7.2 to be .
or
(b) From the values of and given in Problem X7.1,
X7.4 The synchronous machine of Problem X7.1 is now operated as a 2300 V, 60 Hz alternator supplying 800 kW to a 0.8 PF lagging load. Field current . Determine the required input mechanical power to drive the rotor and coupled exciter if the exciter has an efficiency of 91% when supplying the field voltage and current given in Problem X7.1. Assume the lumped friction and windage losses and core losses of Problem X7.1 are valid.
Since is unchanged from Problem X7.1, is still valid. Assume on the reference.
X7.5 Fig. X7.1 shows the phase a circuit of a three-phase synchronous generator that has a per phase load consisting of a pure inductive load. The machine is operating at zero power factor lagging. Determine the ratio .
By voltage division,
or
X7.6 Fig. X7.2 shows the phase a circuit of a three-phase synchronous generator that has a per phase load consisting of a pure capacitive load. The machine is operating at zero power factor leading. Determine the ratio .
By voltage division,
or
X7.7 A 3600 rpm, 60 Hz, 13.8 kV synchronous generator has a synchronous reactance of . The generator is operating at rated voltage and speed with the excitation voltage and the torque angle . Calculate (a) stator current, (b) power factor, and (c) total output power.
(a)
(b)
(c)
X7.8 For the synchronous generator of Problem X7.7, determine (a) the maximum power that can be converted from mechanical to electrical form without loss of synchronism if the field current is unchanged and (b) the value of current for this condition.
(a) Since ,
(b)
X7.9 A three-phase synchronous generator, rated at 240 V, 50 A, 60 Hz, has the stator winding schematic of Fig. X7.3. All 12 phase group leads () are available at the generator terminals. In addition to the given rating, list the balanced, three-phase voltage-current ratings available from the generator by coil reconnection without mix of phase coils that is, use only phase a coils in phase a connections.
Three additional ratings are possible under the stated constraint.
1. Series connect phase coils and use wye configuration: 480 V, 25 A
2. Series connect phase coils and use delta configuration: 277 V, 43.3 A
3. Leave phase coils parallel-connected and use delta configuration: 139 V, 86.6 A
X7.10 The three-phase synchronous generator of Problem X7.9 is to be reconnected as a single-phase alternator. What is the largest possible voltage that can be obtained?
Connect the phase coils in series with additive polarity to give
Or the largest voltage possible is .
X7.11 A 500 MVA, 24 kV, 60 Hz three-phase alternator is operating at rated voltage and frequency with a terminal power factor of 0.8 lagging. The leakage reactance and the synchronous reactance . Stator coil resistance is negligible. The excitation voltage . Determine (a) the torque angle , (b)the total output power, (c) the line current , and (d) the resultant voltage .
(a) The power converted must equal the output power.
or
(b)
EMBED Equation.DSMT4 (c)
(d)
X7.12 A 250 MVA, 24 kV, 60 Hz, three-phase alternator is operating at rated voltage, rated frequency, and rated apparent power with a terminal power factor of 0.8 lagging. Stator coil resistance is negligible. The excitation voltage . Determine (a) the torque angle and (b) the value of synchronous reactance .
(a) Assume on the reference.
Power converted must equal power output.
or
(b)
or
X7.13 A 100 MVA, 13.8 kV, 60 Hz, salient-pole, synchronous generator with 8 poles has and . The stator coil resistance is negligible. The generator is supplying rated apparent power at a power factor of 0.866 lagging. Determine the value of excitation voltage and torque angle .
By [3] of Example 7.10,
Thus,
X7.14 For the salient-pole synchronous generator of Problem X7.13, calculate the developed torque by two methods.
By [7.53] with values from solution of Problem X7.13,
Alternatively for this machine with ,
X7.15 Determine the maximum power that the salient-pole synchronous generator of Problem X7.13 can convert if the field circuit were open circuit.
In [7.53], set , , and multiply by to give
PAGE 2
_1056897599.unknown
_1056902839.unknown
_1056987488.unknown
_1058166078.unknown
_1058166186.unknown
_1058167147.unknown
_1058167242.unknown
_1058167378.unknown
_1058252354.unknown
_1058167276.unknown
_1058167377.unknown
_1058167185.unknown
_1058167204.unknown
_1058167164.unknown
_1058167075.unknown
_1058167108.unknown
_1058166202.unknown
_1058166120.unknown
_1058166173.unknown
_1058166093.unknown
_1056987832.unknown
_1056987941.unknown
_1056988004.unknown
_1056993680.unknown
_1056988122.unknown
_1056987983.unknown
_1056987916.unknown
_1056987735.unknown
_1056987770.unknown
_1056987654.unknown
_1056903739.unknown
_1056904284.unknown
_1056904596.unknown
_1056904947.unknown
_1056905114.unknown
_1056905135.unknown
_1056905215.unknown
_1056905349.unknown
_1056905145.unknown
_1056905123.unknown
_1056905018.unknown
_1056904781.unknown
_1056904904.unknown
_1056904691.unknown
_1056904381.unknown
_1056904474.unknown
_1056904347.unknown
_1056904052.unknown
_1056904167.unknown
_1056904237.unknown
_1056904105.unknown
_1056903800.unknown
_1056903824.unknown
_1056903791.unknown
_1056903162.unknown
_1056903402.unknown
_1056903724.unknown
_1056903202.unknown
_1056902942.unknown
_1056903110.unknown
_1056902854.unknown
_1056899972.unknown
_1056900457.unknown
_1056902595.unknown
_1056902683.unknown
_1056902817.unknown
_1056902638.unknown
_1056900682.unknown
_1056902396.unknown
_1056900629.unknown
_1056900328.unknown
_1056900411.unknown
_1056900443.unknown
_1056900383.unknown
_1056900153.unknown
_1056900258.unknown
_1056900047.unknown
_1056898686.unknown
_1056899058.unknown
_1056899323.unknown
_1056899397.unknown
_1056899104.unknown
_1056898831.unknown
_1056898954.unknown
_1056898786.unknown
_1056898402.unknown
_1056898600.unknown
_1056898622.unknown
_1056898536.unknown
_1056898119.unknown
_1056898280.unknown
_1056898075.unknown
_1056896261.unknown
_1056897079.unknown
_1056897275.unknown
_1056897366.unknown
_1056897500.unknown
_1056897341.unknown
_1056897113.unknown
_1056897156.unknown
_1056897098.unknown
_1056896742.unknown
_1056896979.unknown
_1056897065.unknown
_1056896775.unknown
_1056896722.unknown
_1056896728.unknown
_1056896283.unknown
_1056809185.unknown
_1056893704.unknown
_1056894310.unknown
_1056894397.unknown
_1056893746.unknown
_1056809219.unknown
_1056809659.unknown
_1056809207.unknown
_1056808572.unknown
_1056808616.unknown
_1056808881.unknown
_1056808597.unknown
_1056808499.unknown
_1056808549.unknown
_1056808434.unknown