1
LPG Bulk Tank Lorry
18 Tonnes
Bharat PetroleumCenter of Tank
XX 00 XX 0000
NP
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101 AMBULANCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
35% of Height
10%
300
300
38% of Height
150300
A
A
B B
Center of Tank
1125 30
0
3750 2400
8100
All dimensions in mmTypical illustration of vehicle with enlarged size of BPCL name and logo. If the height of the white panel is
insufficient to accomodate the BPCL logo unit, refer to Annexures 5 & 6 for resizing the logo unit.
2
LPG Bulk Tank Lorry
18 Tonnes
NP
35% of Height
10%
350
1550
300
300
38% of Height
150
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101 AMBULA NCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
XX 00 XX 0000
Center of Tank
B B 1125
300Center of Tank24
00
8100
All dimensions in mmTypical illustration of vehicle with enlarged size of BPCL name and logo. If the height of the white panel is
insufficient to accomodate the BPCL logo unit, refer to Annexures 5 & 6 for resizing the logo unit.
3
Bharat Petroleum
2
2
NATIONAL PERMIT Valid in the states of aakjsdf jdfbdf bdfg ndfbb dfgbcv dfgkfgj g gh
GOODS CARRIER
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101 AMBULA NCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
XX 00 XX 0000
600
800
200
100
600
630
200
35%
30%
LPG Bulk Tank Lorry
18 Tonnes
All dimensions in mm
4
LPG Bulk Tank Lorry
6 Tonnes
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101 AMBULA NCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
NP
Bharat Petroleum
XX 00 XX 0000
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101 AMBULA NCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
NP
XX 00 XX 0000
LPG cylinder Truck Small Front
XX 00 XX 0000
Bharat Petroleum
2
2
NATIONAL PERMIT Valid in the states of aakjsdf jdfbdf bdfg ndfbb
dfgbcv dfgkfgj g gh
GOODS CARRIER
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101AMBULA NCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
XX 00 XX 0000
MOBILE: 0000000000 / 0000000000
XO OXOX XOX XO ROADLINES
5
Basic Elements of Design
1. Base colour Under the Motor Vehicles Act, 1988 the base colour of all vehicles plying
under National Permit and carrying dangerous or hazardous goods must be white.
2. Emergency Information Panel (EIP)
For LPG Vehicles
800
600
CORRECT TECHNICAL NAMELIQUIFIED PETROLEUM GAS
UN No. 1075HAZCHEM 2WEIN EMERGENCY DIAL:POLICE : 100 FIRE : 101 AMBULANCE : 102
SPECIALIST ADVICEUSE DRY CHEMICAL POWDER TYPE FIRE EXTINGUISHER
2
Every goods carriage used for transporting dangerous or hazardous goods is required to display the EIP on left, right and rear side of the vehicle in size 60 cm x 80 cm giving details as specified under section 88(12) of the Motor Vehicles Act, 1988.
Refer Annexure 1 for details.
3. class Label
The Class Label of the dangerous or hazardous goods in the size not less than 250 mm square must be placed on the front of the vehicle, at the top and near the middle.
For LPG Vehicles
2
250
250
4. conspicuity Reflective Marking Conspicuity reflective marking strips of 5 cm width are required on all 4
sides of the vehicle as follows:
• Leftandrightsideinyellowcolour
• Rearsideinredcolour
• Frontsideinwhitecolour
Refer Annexure 2 for details.
Statutory Requirements
6
5. National Permit
Vehicles having a National Permit must have a ‘dry leaf brown’ colour strip of 5 cm width across the center of the vehicle on left and right side, and in orange colour on the cabin.
The words National Permit, or NP in short, must be displayed on both sides of the vehicle in a circle of 30 cm diameter.
NP
The text “National Permit Valid in the states of .........” written in blue colour on a white board should be displayed on the front top of the vehicle or as a sticker just below the top edge of the wind screen.
NatioNal Permit Valid in the states of aakjsdf jdfbdf bdfg bdfg bdfg
Refer Annexure 3 for details.
6. Goods carrier The words ‘Goods Carrier’ are required to be displayed on the
front top of the driver’s cabin as shown in the illustrations of the LPG Bulk Tank Lorry.
7. Registration No.
XX 00 XX 0000
The registration number of the vehicle should be displayed on left, right and rear sides of the vehicle’s tank or body in addition to the regular registration number plates.
Refer Annexure 4 for details.
8. Transporter Details Panel
The panel for name and contact number of the transporter will be placed 5 cm below the EIP panel on the rear side of the vehicle.
Refer Annexure 4 for details.
Basic Elements of DesignStatutory Requirements (cont.)
7
Basic Elements of Design
1. Bharat Petroleum
The brand name ‘Bharat Petroleum’ will be placed on the center of the tank / panel, on the right side of the vehicle (Driver’s side) in Hindi and on the left side in English. It will generally be base-aligned with the horizontal center line of the tank and centralised with respect to the length of the tank. It will be printed on vinyl in blue and applied on the tank surface or panels. Refer Annexure 5 for details.
2. BPcL Logos
The logos in English and Hindi will be printed on vinyl and applied on the left and right side of the vehicles respectively. To enhance the visibility of the logo, a shadow has been added on two sides. The logo must always be centralised vertically between the top wave panel and the bottom blue panel. Refer Annexure 6 for details.
3. BPcL Wave
The yellow and blue wave design has been adapted from the facia of the canopy of the retail outlets, which has high visibility and has become the icon for Bharat Petroleum. It will always be placed at the top of the vehicle and will help give the entire fleet a distinct identity. This yellow and blue panel will be printed on vinyl and applied to the tank surface
Refer Annexure 7 for details.
4. Bottom Panel
The blue colour panel along the bottom of the tank gives a base to the design. This panel will be painted in blue colour exactly matching the blue colour of the vinyl sticker.
5. SmartLine
The vinyl sticker for SmartLine unit will be applied on the rear side of the vehicles(exceptAFS)
Refer Annexure 8 for details.
Branding
8
Basic Elements of DesignBranding (cont.)
6. Sub-brand
The sub-brand ‘Bharatgas’ will be printed on vinyl and placed on the rear side of the vehicle.
Refer Annexure 8 for details.
9
Annexure 1
RTO Guidelines – EIP
Emergency Information PanelIn India, it is mandatory for the vehicles transporting hazardous chemicals to display Emergency Information Panel (EIP) with details and at places as specified under Rule 134 of the Central Motor Vehicles Rules, 1989 as shown in the next figure.
Every goods carriage used for transporting any dangerous or hazardous goods shall be legibly and conspicuously marked with an emergency information panel in each of the three places as specified, so that the emergency information panel faces to each side of the carriage and to its rear and such panel shall contain the following information viz.,
The correct technical name of the dangerous or hazardous goods in letters not less than 50 mm high.
The United Nations class number for the dangerous goods in letters not less than 100 mm high (Rule 137).
The class label of the dangerous or hazardous goods in the size of not less than 250 mm square.
The name and telephone number of the emergency services to be contacted in the event of fire or any other accident in letters and numerals that are not less than 50 mm high and the name and telephone number of the consignor of the dangerous or hazardous goods or of some other person from whom expert information and advice can be obtained concerning the measures that should be taken in the event of emergency.
Every class label and emergency information panel (EIP) shall be marked on the goods carriage and shall be kept free and clean from obstruction at all times.
The emergency information panel (EIP) should have dimensions as shown in the next figure.
One practical problem encountered with the use of EIP is the selection of the substance identification number and the HAZCHEM code to be incorporated in the EIP when a tanker transports different chemicals in different compartments. The solution in such case is to incorporate the word “Mixed Load” in the sections of EIP earmarked for “UN Number” and “HAZCHEM” and to label each compartment separately with the UN number and HAZCHEM code corresponding to the chemical in the compartment.
10
Annexure 2
Reflective conspicuity Strip
conspicuity Marking Strip
This is a retroreflective flexible microprismatic marking designed to mark the front, sides and rear of vehicles for enhanced visibility and detection. It comes in strip form with pressure sensitive adhesive and paper liner.
The following colour conspicuity marking stripes must be used:
White for the front of the vehicle.
Yellow for the left and right side.
Red for the rear of the vehicle.
Minimum width of the marking strip should be 5 cm.
Physical properties:
The conspicuity marking strip should have the following physical properties:
1. High bonding strength
2. Resistance to corrosion
3. Resistance to fuels
4. Resistance to heat
5. Resistance to penetration of water
6. Resistance to power washing
7. Good flexing / bending ability without cracking
AIS Specification for Retro-refelctive Marking
The conspicuity marking strip should meet AIS standard specification AIS 090 for retro-reflective marking of Heavy and Long Vehicles, their Trailers and Semi-Trailers
The minimum coefficient of retroreflective values of these markings are given below in terms of candelas per square metre:
Table 1
Minimum values for the coefficient of Retro-reflection R’ (cd.m-2.lx-1 )Observation angle α (°) Entrance Angle β (°)α = 0.33° (20´) β1 0 0 0 0
β2 5 30 40 60ColorYellow 300 130 75 10White 450 200 90 16
Table 2
Maximum values for the coefficient of Retro-reflection R’ (cd.m-2.lx-1 )Observation angle α (°) Entrance Angle β (°)α = 0.33° (20’) β1 0 0 0 0
β2 5 20 30 40ColorRed 120 60 30 10
Table 3 – CIE Chromaticity Coordinates Limits
Chromaticity Co-ordinatesColor 1 2 3 4
Yellow x 0.585 0.610 0.520 0.505y 0.385 0.390 0.480 0.465
White x 0.373 0.417 0.450 0.548y 0.402 0.359 0.513 0.414
Red x 0.720 0.735 0.665 0.643y 0.258 0.265 0.335 0.335
11
Annexure 3
RTO Guidelines – National Permit
Extracts of Permit conditions for National Permits in respect of Goods carriages issued under section 88(12) of the Motor Vehicles Act, 1988
National PermitNational Permit in respect of goods carriages are governed by Section 88 (12) of Motor Vehicles Act, 1988 and Central Government is competent to lay down permit conditions for these permits. Central Government has already prescribed conditions under Central Motor Vehicles Rules, 1989, which are, reproduced hereinunder.
90. Additional conditions for National Permit The National Permit issued under sub-section (12) of section 88 of Motor
Vehicle Act, 1988 shall be subject to the following additional conditions, namely:
1. The vehicle plying under a national permit shall be painted by in dry leaf brown colour with thirty centimeters broad white borders and the words “National Permit” shall be inscribed on both sides of the vehicles in bold letters within a circle of thirty centimetres diameter.
PROVIDED That the body of a tanker carrying dangerous or hazardous goods shall be painted in white colour with a dry leaf brown ribbon of 5 centimetres width around in the middle at the exterior and that of the driver’s cabin in orange colour.
2. A board with the inscription ‘National Permit’ valid in the State(s) of . . . . . with blue letters on white background shall be carried in front top of such vehicle.
For National Permit Vehicles Logo, Board and Strips
NP
Dry leaf brown colour strip of 50 mm width for the left and right sides of the tank
Orange colour strip of 50 mm width for the left and right sides of the cabin
NatioNal Permit Valid in the states of aakjsdf jdfbdf bdfg ndfbb ndfbb ndfbb
White Board with the text in blue colour in Arial Bold font in 70 mm height to be placed on the front top of the vehicle or as a sticker just below the
top edge of the wind screen.
30 cm dia
All dimensions in mm
12
Annexure 4
Transporter Details Panel
company Owned Vehicle
contractor Owned Vehicle
COMPANY OWNED TANK LORRY
BPCL SEWREE Tel. 000- 00000000Bharat Petroleum
600
200
Abcdefghij Depot. Tel.: 000-00000000
MOBILE: 0000000000 / 0000000000XO OXOX XOX XO ROADLINES
600
200
XX 00 XX 0000500
100 XX 00
XX 0000
250
200
7070
Goods carrier840
Goods CarrIEr70
1200
100 Goods CarrIEr
RTO Registration No.
The registration number of the vehicle should be displayed on left, right and rear sides of the vehicle’s tank or body in addition to the regular registration number plates.
The Registration number should be in minimum 70 mm height in Arial Bold font in black colour on a yellow plate.The panel will be in white colour with text in black. Take name of transporter
in 80 mm height and remaining text in 70 mm height. All dimensions in mm
13
Annexure 5
Standard SizeForTankLorriesofcapacity18KLandabove(Retail,Lubes,Aviation)and18Tonnes(LPGBulkTankLorry)
Reduced Size ForTankLorriesofcapacity12KLto15KL(Retail,Lubes,Aviation)and6Tonnes(LPGBulkTankLorry)
192 Bharat Petroleum
2400
370
2160
Bharat Petroleum Brand Name
All dimensions in mm
3000
240
270046
0
14
Annexure 5 (cont.)
Enlarged SizeForlargeAviationRefuellersandLPGBulkTankLorries
Bharat Petroleum Brand Name
BlueCMYK : C-100,M-40,Y-0,K-0
Pantone : 300 C
300
3750
1550
350
All dimensions in mm
15
All dimensions in mm
Annexure 6
For Tank Lorries below 12 KL, reduce size proportionately
644
900
900
644
550
765
550
765
BPcL Logo with Shadow
Standard SizeForTankLorriesofcapacity18KLandabove(Retail,Lubes,Aviation)and18Tonnes(LPGBulkTankLorry),Preferred size, as indicated here
Reduced Size ForTankLorriesofcapacity12KLto15KL(Retail,Lubes,Aviation)and6Tonnes(LPGBulkTankLorry),Preferred size, as indicated here
size Adaptation, if required: The above sizes are based on the average sizes of the tank lorries as shown in this manual. However, if the white panel on the left and right side of the tank lorry (between the top wave design and the bottom blue panel) is insufficient, the height of the BPCL Logo unit i.e. including the tag line (energising lives), should be reduced to 75% of the height of the white panel, and positioned with equal white space above and below the logo unit.
16
Annexure 6 (cont.)
BPcL Logo with Shadow
Enlarged SizeForlargeAviationRefuellersandLPGBulkTankLorries
766
1125
766
1125
All dimensions in mm
BlueCMYK : C-100,M-40,Y-0,K-0
Pantone : 300 C
YellowCMYK : C-0,M-10,Y-100,K-0
Pantone : 109 C
17
Wave on Facia of canopy of Retail Outlet
Standard Wave Design for BPcL Fleet
Annexure 7
Wave Design
Size: 200 mm x 1364 mm
Basic Wave Unit
Extended Wave Unit
Size: 600 mm x 1364 mm
Size: 200 mm x 1364 mm
Basic Wave Unit
1364 13641364
200
400
Size: 200 mm x 1364 mm
Basic Wave Unit
Extended Wave Unit
Size: 600 mm x 1364 mm
Size: 200 mm x 1364 mm
Basic Wave Unit
Extended Wave Unit
Size: 600 mm x 1364 mm
Size: 600 mm x 1364 mm
Extended Wave Unit
All dimensions in mm
18
Annexure 8
SmartLine Logo330
150
Bharatgas Logo600
200
All dimensions in mm