ASC-005B (G650) RAASTRANSMITTAL SHEET This sheet transmits Revision
A, dated June 27, 2016, of Gulfstream G650ER Aircraft Service
Change 005, issued October 15, 2014, and titled Navigation (ATA 34)
– Runway Awareness Advisory System (RAAS) - Installation. Reason
for Revision: Approving Authority:
Added EASA design change classification and approval due to the
recent validation of the G650ER by the EASA.
Prerequisites: Updated disk creation information
Price: Reformatted and updated information
Modification instructions: Step N. Updated language
NOTE: This ASC revision does not change the approved ASC design /
configuration and therefore does not require further regulatory
agency approval.
Effect of Revision on Prior Accomplishment: This ASC revision
replaces ASC 005. Aircraft operators who have previously complied
with ASC 005 are in compliance with this revision and should return
the service reply card marked “Previously complied with.” Note:
This bulletin has been reproduced in its entirety. A black bar in
the left margin indicates a
change in that line of text or figure.
List of Effective Pages:
5 June 27, 2016
Revision History: Original Issue: October 15, 2014 Revision A: June
27, 2016
June 27, 2016 Transmittal
JUNE 27, 2016
PILOTS INFORMATION SHEET
This service change is designed to reduce runway incursion events
by improving flight crew situational awareness with the
introduction of timely aural advisories during taxi, take-off,
final approach and landing rollout operations. Advisories are
generated based on current aircraft position relative to airport
operations. Gulfstream G650ER Airplane Flight Manual,
GAC-AC-G650ER-OPS-0001, Revision “-“ or later approved revision is
required.
PLEASE DETACH AND GIVE TO FLIGHT DEPARTMENT PERSONNEL
Aircraft Service Change prepared by Gulfstream Aerospace, Savannah
International Airport, PO Box 2206, Savannah Georgia, 31402-2206,
USA. © 2016, Gulfstream Aerospace. All rights reserved, including
the right to reproduce this publication. No part may be reproduced,
stored in any retrieval system or transmitted in any part or form
or by any means electronic, photocopying, microfilm, microfiche,
mechanical or otherwise, without prior written permission of
Gulfstream Aerospace.
This technical data is controlled under the Export Administration
Regulations by General License TSU. It may not be transferred to a
third party without the prior written approval of the U.S.
Department of Commerce.
Revision A June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
PILOTS INFORMATION SHEET
This service change is designed to reduce runway incursion events
by improving flight crew situational awareness with the
introduction of timely aural advisories during taxi, take-off,
final approach and landing rollout operations. Advisories are
generated based on current aircraft position relative to airport
operations. Gulfstream G650ER Airplane Flight Manual,
GAC-AC-G650ER-OPS-0001, Revision “-“ or later approved revision is
required.
PLEASE RETAIN THIS COPY WITH THE AIRCRAFT SERVICE CHANGE (ASC)
BOOKLET
Aircraft Service Change prepared by Gulfstream Aerospace, Savannah
International Airport, PO Box 2206, Savannah Georgia, 31402-2206,
USA. © 2016, Gulfstream Aerospace. All rights reserved, including
the right to reproduce this publication. No part may be reproduced,
stored in any retrieval system or transmitted in any part or form
or by any means electronic, photocopying, microfilm, microfiche,
mechanical or otherwise, without prior written permission of
Gulfstream Aerospace.
This technical data is controlled under the Export Administration
Regulations by General License TSU. It may not be transferred to a
third party without the prior written approval of the U.S.
Department of Commerce.
Revision A June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
The design change effected by this Aircraft Service Change (ASC)
has been classified as Major by the United States Federal Aviation
Administration (FAA) and Major Level 1 by the European Aviation
Safety Agency (EASA). The design change data contained herein and
effected by this document is approved and accepted by the FAA under
FAA Project Number TC8700AT-T and by the EASA under EASA Project
number P-EASA-IM.A.169. The design of this ASC is approved by
aircraft type design data for installation on aircraft registered
for operation in accordance with applicable regulations of the FAA
and EASA. The design of an ASC is configured to a standard (green)
production aircraft. If spare wires, pin connections or locations
called out have been used for another modification, the installing
agency must ensure the development, documentation and approval of
any required deviations.
The following instructions, in step-by-step form, are written as a
guide to perform this ASC. Compliance with safe maintenance
practices as defined in the Aircraft Maintenance Manual and FAA or
EASA regulations is required.
Gulfstream considers this ASC a means to enhance aircraft
capabilities to meet individual operator requirements. The
modification is not related to any safety or airworthiness
condition.
Subject: Navigation (ATA 34) – Runway Awareness Advisory System
(RAAS) – Installation
Purpose / Discussion: This service change is designed to reduce
runway incursion events by improving flight crew situational
awareness with the introduction of timely aural advisories during
taxi, take-off, final approach and landing rollout operations.
Advisories are generated by the monitor warning system based on
current aircraft position relative to airport runways. The RAAS
uses Global Positioning System (GPS) data to determine current
aircraft position when compared to the location of airport runways
that reside within the internal EGPWS Terrain/Obstacle/Airport
Database.
Description / Labor-Hours Required Per Aircraft:
This service change installs the following new hardware and
software:
RAAS annunciator / inhibit switch on the center pedestal and
associated wiring Loadable Options disk to activate RAAS Aircraft
Personality Module (APM) Settings disk for advisory call-outs,
distance units, audio levels, and gender selection
Approximately 16 labor-hours will be required for this
installation.
Revision A Page 1 of 8 June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
Approved Engineering Data: The source data for this aircraft
service change is: 60A3446000-001 Rev. “–” Runway Awareness
Advisory System (RAAS) ASC-005 Configuration Control Document
60A2510001N002 Rev. “–” Panel Install – Pedestal Switch Mod
60A3446005W Rev. “–” Wiring Diagram, RAAS Inhibit Push-Button
Installation
Prerequisites: Prior to, or at the time this ASC is ordered,
operators will be required to supply a configuration report of the
Central Maintenance Computer (CMC). The CMC report can be stored on
the aircraft PC laptop then electronically submitted to Gulfstream
at
[email protected]. Allow up to 10 days for the
creation of a new Options Data disk. Submit APM Settings &
Riggings form available on MyGulfstream.com under
Communications/Forms and Surveys/Aircraft Software Forms.
Concurrent Requirement: None
Associated Documents: G650ER Aircraft Maintenance Manual (AMM),
Chapter 20, 31, 33 and 34. G650ER Wiring Diagram Manual (WDM),
Chapter 34
Flight Manual Revision / Supplement Required:
Gulfstream GVI (G650ER) Airplane Flight Manual,
GAC-AC-G650ER-OPS-0001, Basic Issue or later approved revision is
required.
Publications Data: Data concerning this service change will be
published in a future revision of the affected manual(s). This
booklet will provide technical data until the revision(s) is
published.
Effectivity: This service change is applicable to aircraft serial
numbers 6001 and subsequent.
Effect on Spares: None
Special Equipment / Tools Required:
Gulfstream G650ER Aircraft Service Change 005
Skill Type Required: Knowledge of the G650ER PlaneView avionics
system and software loading procedures will be required for this
installation.
Price: Contact your Regional Sales Manager for pricing
information.
NOTE: Prior to ordering the ASC kit, operators must provide a
Configuration Report of the Central Maintenance Computer (CMC) and
the APM Settings & Riggings form to Gulfstream Product Support.
The CMC configuration report must be electronically submitted to
Gulfstream at
[email protected]. The interactive APM
Settings & Riggings form is available to authorized users at
myGulfstream.com. An aircraft specific Options disk and APM disk
will be created.
Revision A Page 3 of 8 June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
MODIFICATION INSTRUCTIONS:
CAUTION: PROTECT WIRE BUNDLES, CONNECTORS AND SURROUNDING STRUCTURE
DURING ANY MAINTENANCE PROCEDURE FROM SHAVINGS, DEBRIS AND
CONTAMINATION. MAINTAIN A PROPERLY CLEANED WORK AREA THROUGHOUT THE
PROCEDURE TO ENSURE THE INTEGRITY OF THE AFFECTED COMPONENT /
SYSTEM. VISUALLY INSPECT WORK AREA USING ADDITIONAL LIGHT AS
NECESSARY TO VERIFY ABSENCE OF ANY DEBRIS PRIOR TO COMPLETION OF
PROCEDURE. FAILURE TO COMPLY MAY RESULT IN DAMAGE TO COMPONENTS AND
/ OR SYSTEMS.
A. Prepare the aircraft for safe maintenance. Refer to G650ER AMM,
Chapter 20, Safe Ground Maintenance Procedures.
B. Remove the cockpit center pedestal switch panel, P/N
60P3110907A. Refer to G650ER AMM, Chapter 31, Pedestal Switch Panel
– Removal / Installation.
C. On a clean work table, modify the pedestal switch panel as
follows: (Refer to Figure 1)
1. Temporarily remove the following switches and guards from the
pedestal panel: TERRAIN DISPLAY, FLT CTRL RESET, GPWS GRND SPLR
FLAP ORIDE, and GND SPOILER. Refer to G650ER AMM, Chapter 33,
Switch Assembly (Korry) Removal / Installation.
2. Remove and discard the existing overlay panel, P/N
60P3110900Z021.
3. Install overlay panel, P/N 60P3110900Z040.
4. Install Socket Outer Sleeve, P/N 27498-001, Spacer, P/N
27498-008 and LED Switch Assembly, P/N 27500-008. Torque screws to
16-20 inch-ounces.
5. Install switches previously removed in Step C.1. Refer to G650ER
AMM, Chapter 33, Switch Assembly (Korry) Removal /
Installation.
6. Remove existing end caps, 104EC11, 12, 13, 14, 15, and 16. Strip
wires, crimp contact, P/N M39029/22-192 and terminate wires as
shown. Refer to Figure 2.
7. Using a Sharpie indelible marker, permanently identify the
pedestal switch panel as P/N 60A3110907A001
D. Install pedestal panel, P/N 60A3110907A001 and secure. Refer to
G650ER AMM, Chapter 31, Pedestal Switch Panel – Removal /
Installation.
E. Prior to loading the APM Settings disk, verify the disk part
number matches the 60BSWCD052 APM Settings Authorization
Report.
F. Load the APM Settings disk. Refer to 60BSWCD052 APM Settings
Authorization Report and G650ER AMM, Chapter 20, Software
Maintenance Practices.
Revision A Page 4 of 8 June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
NOTE: When multiple ASCs containing software are complied with
simultaneously, only the Loadable Avionics Software Configurations
(Options) disk containing the final configuration should be loaded.
In the event of multiple Options disks, the final configuration is
determined by referring to the Authorization Report (AR) with the
most recent time and date stamp.
G. Prior to loading the Options disk, verify the disk part number
matches the 60BSWCD050 Loadable Avionics Software Configuration
Authorization Report.
H. Load the Options disk. Refer to 60BSWCD050 Loadable Avionics
Software Configuration Authorization Report and G650ER AMM, Chapter
20, Software Maintenance Practices.
I. Perform the Verification and Test Procedures found on the
Authorization Report(s).
J. Store all current software on board the aircraft. Dispose of all
obsolete disks.
K. Ensure work area is clean and clear of foreign objects and
debris (FOD).
L. Document the following software information on the attached
service reply card and on the PlaneView Configuration Record in the
aircraft permanent maintenance records.
Top Level System Part Number Media Part Number Media Serial
Number
M. Record compliance with this aircraft service change in the
aircraft’s permanent maintenance records and return aircraft to
flight status.
N. Report compliance with this service change to Gulfstream CMP by
uploading the attached service reply card, along with the CMP task
card(s) sign-off using MyGulfstream, MyCMP Document Upload, or
e-mail to
[email protected], or fax to Gulfstream CMP at
800-944-1775 or 912-963-0265.
WEIGHT AND BALANCE DATA: The effect of this change with regard to
aircraft basic weight and balance is as follows:
MOD
ELECTRICAL LOAD ANALYSIS DATA:
The effect of this change on the aircraft electrical loading is not
affected.
Revision A Page 5 of 8 June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
PARTS REQUIRED PER AIRCRAFT: Item Part Number Nomenclature Qty.
Notes/Alt./Substitutes
-1 Kit 1. 60A3446000-001-SW Software Package (ASC-005) 1 See Note
1, 2, 3 2. 60BSWCD050 Loadable Avionics Software
Configuration (Options Disk) Ref. See Note 2, 3
3. 60BSWCD052 Aircraft Personality Module (APM) Settings &
Riggings
Ref. See Note 2, 3
4. 27498-008 Connector Accessory – Spacer, Korry
1 -
5. 27500-008 LED Switch Assembly – Korry 1 - 6. 60P3110900Z040 SCM,
Overlay Panel –
Pedestal Multi Button 1 -
7. M39029/22-192 Contact Socket 6 - 8. 27498-001 Socket (Outer
Sleeve) 1 -
NOTE 1: All documents and publications will be issued to the latest
revision.
NOTE 2: 60BSWCD052 establishes the requirements of the APM Settings
disk while 60BSWCD050 establishes the Options disk. The disks are
aircraft serial number specific. The part number is determined at
the time of ASC kitting. All software CDs required for this ASC
will be packaged as P/N 60A3446000-001-SW (Item 1).
NOTE 3: Prior to ordering the ASC kit, operators must provide a
Configuration Report of the Central Maintenance Computer (CMC) and
the APM Settings & Riggings form to Gulfstream Product Support.
The CMC configuration report must be electronically submitted to
Gulfstream at
[email protected]. The interactive APM
Settings & Rigging form is available to authorized users at
myGulfstream.com. An aircraft specific Options disk and APM disk
will be created.
Revision A Page 6 of 8 June 27, 2016
Gulfstream G650ER Aircraft Service Change 005
FIGURE 1
Gulfstream G650ER Aircraft Service Change 005
FIGURE 2
Gulfstream G650ER Aircraft Service Change 005
SERVICE REPLY CARD Please upload this page, along with the CMP task
card(s) sign-off using MyGulfstream, MyCMP Document Upload, or
e-mail to
[email protected] or fax to Gulfstream CMP at
800-944-1775 or 912-963-0265.
THE FOLLOWING AIRCRAFT SERVICE CHANGE HAS BEEN COMPLIED WITH:
ASC NUMBER A/C AIRCRAFT TYPE COMPLIANCE DATE 970051 G650ER
AIRCRAFT HOURS:
AIRCRAFT LANDINGS:
NOT APPLICABLE: DATE:
OFF: ON:
PART NUMBER MEDIA PART
APM DISK
OFF: ON:
OPTIONS DISK
OFF: ON:
COMMENTS / SUGGESTIONS / ACTIONS TAKEN:
Aircraft Service Change prepared by Gulfstream Aerospace, Savannah
International Airport, PO Box 2206, Savannah Georgia, 31402-2206,
USA. © 2016, Gulfstream Aerospace. All rights reserved, including
the right to reproduce this publication. No part may be reproduced,
stored in any retrieval system or transmitted in any part or form
or by any means electronic, photocopying, microfilm, microfiche,
mechanical or otherwise, without prior written permission of
Gulfstream Aerospace.
This technical data is controlled under the Export Administration
Regulations by General License TSU. It may not be transferred to a
third party without the prior written approval of the U.S.
Department of Commerce.
Revision A June 27, 2016