ANAMA Package & Container Testing Services, Inc.
607 Fayette Avenue, Mamaroneck, NY 10543
Tel: (914) 899-3300 | Fax: (914) 899-3325
[email protected] | www.anamapackagetesting.com
Project #2477
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 1 of 72
DEPARTMENT OF TRANSPORTATION
PERFORMANCE ORIENTED PACKAGE TESTING
CERTIFICATION
Testing Performed by:
ANAMA Package & Container Testing Services, Inc. (+CM)
Approval CA2013040016
607 Fayette Avenue
Mamaroneck, NY 10543
(914) 899-3300
Testing Performed for:
Owen Oil Tools, Inc.
12001 County Road 1000
Godley, TX 76044
Mr. Matt Holzer
(817) 551-0540
4G Design Re-Qualification Testing
Iteration 1: Fibreboard Box with 2-11.4 Kg Average Gross Weight Barrier Bags (4 SLOT)
Iteration 2: Fibreboard Box with 2-11.2 Kg Average Gross Weight Barrier Bags (MEDIUM HOLE)
Iteration 3: Fibreboard Box with 2-11.4 Kg Average Gross Weight Barrier Bags (2 ½ HEX)
Iteration 4: Fibreboard Box with 10-2.24 Kg Average Gross Weight Steel Cylinder Assemblies (001-UNI DET)
Box ID: 1313-700
4G / Y 23.7 / S / **
USA / +CM0428
** insert year the packaging is manufactured
________________________________________________________________________
Anton Cotaj, Certification Officer
u n
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ANAMA Package & Container Testing Services, Inc.
607 Fayette Avenue, Mamaroneck, NY 10543
Tel:(914) 899-3300 | Fax: (914) 899-3325
[email protected] | www.anamapackagetesting.com
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 2 of 72
SECTION 1 - CERTIFICATION
4G Design Re-Qualification Testing of the Owen Oil Tools, Inc., Godley, TX Packages
Iteration 1: Fibreboard Box with 2-11.4 Kg Average Gross Weight Barrier Bags (4 SLOT)
Iteration 2: Fibreboard Box with 2-11.2 Kg Average Gross Weight Barrier Bags (MEDIUM HOLE)
Iteration 3: Fibreboard Box with 2-11.4 Kg Average Gross Weight Barrier Bags (2 ½ HEX)
Iteration 4: Fibreboard Box with 10-2.24 Kg Average Gross Weight Steel Cylinder Assemblies (001-UNI DET)
Box ID: 1313-700
Requesting Party:
Owen Oil Tools, Inc. Tel: (817) 551-0540
12001 County Road 1000, PO Box 765 Email: [email protected]
Godley, TX 76044
Attn: Mr. Matt Holzer
ANAMA Packaging & Container Testing Services, Inc. is a current DOT UN Third-Party Certification Agency under
§107.403 and certifies that the Owen Oil Tools, Inc., Godley, TX packaging prepared as for transport, referenced above and
tested in May & June 2019 has passed the Standards of the US Department of Transportation, Title 49CFR, Performance
Oriented Packaging Standards; Section 178. This package is also certified under IMDG and UN Recommendations of the
Committee of Experts on the Transportation of Dangerous Goods. It is the responsibility of the shipper / end user to ensure
appropriate use.
The use of other packaging methods or components other than those documented in this report may render this report
invalid.
SUMMARY OF PERFORMANCE TESTS
Test Specification Test Level Time Results
Drop 49 CFR 178.603 1.2 m N/A Pass
Stacking 49 CFR 178.606 347.3 kg 24 Hours Pass
Cobb 49 CFR 178.516 122.2 gr/m² 30 Minutes Pass
Vibration 49 CFR 178.608 235 CPM 60 Minutes Pass
Test Report #0428
UN Marking (49 CFR 178.503)
4G / Y 23.7 / S / **
USA / +CM0428
Package Identification Code 4G - Fibreboard Box (49 CFR 178.516)
Performance Standard Y - Packaging meets Packing Group II and III Tests
Authorized Gross Mass 23.7 kg (52.14 lbs)
"S" Designation Denotes Inner Packaging
Year of Manufacture ** Insert year the packaging is manufactured
Country Authorizing The Mark USA
DOT UN Third-Party Certification Agency (+CM) ANAMA Package & Container Testing Services, Inc.
Approval CA2013040016
Third Party Packaging Identification Number +CM0428
________________________________________________________________________
Anton Cotaj, Certification Officer
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 3 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
SECTION 2 – DESCRIPTION OF THE TESTED PACKAGE
Iteration 1 (4 SLOT):
Two (2) up to 11.4 kg average gross weight solid product simulant filled barrier bags, inner packagings, stacked on top of
each other within a regular slotted fibreboard carton (International Box Code 0201) outer packaging with double-wall
corrugated sheets on top and bottom.
Iteration 2 (MEDIUM HOLE):
Two (2) up to 11.2 kg average gross weight solid product simulant filled barrier bags, inner packagings, stacked on top of
each other within a regular slotted fibreboard carton (International Box Code 0201) outer packaging with double-wall
corrugated sheets on top and bottom.
Iteration 3 (2 ½ HEX):
Two (2) up to 11.4 kg average gross weight solid product simulant filled barrier bags, inner packagings, stacked on top of
each other within a regular slotted fibreboard carton (International Box Code 0201) outer packaging with double-wall
corrugated sheet on top.
Iteration 4 (001-UNI DET):
Ten (10) up to 2.25 kg average gross weight solid product filled steel pipes with screw on end caps, inner packagings each
filled with up to 730 grams average gross weight of solid product. The steel pipe assemblies are placed sideways 2-layers
high, 5 assemblies per layer within the center special slotted fibreboard carton (International Box Code 0204) outer
packaging with double-wall corrugated sheets on top, bottom, sides and between layers and side honeycomb pads.
The use of other packaging methods or components may render this report invalid.
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 4 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
INNER PACKAGING #1 – Reference Section 7 for drawings
BARRIER BAG [ITERATIONS: 1 (4 Slot), 2 (MH-7) & 3 (2 ½ HEX)]
Quantity 2
Style/Description
Laminated watervaporproof, greaseproof,
flexible barrier bag with heat-sealed bottom
and sides
Type MIL-PRF-131K, Type 1, Class 1, Style 1
Manufacturer Cadillac Products Packaging Company
Supplier East Texas Seals, LLC, Dallas, TX
Part # MB20.5X18
Material of Construction Plastic/foil/plastic laminate, 5 Mil nominal
gauge
Minimum Thickness 0.120 mm (0.0045")
Nominal Thickness 0.127 mm (0.005")
Dimension (mm, OD), W X L, flat 475 x 530
Dimension (mm, ID), W X L, flat 445 x 470
Dimension (mm, OD) filled
Iteration 1: 340 x 340 x 65
Iteration 2: 340 x 340 x 30
Iteration 3: 340 x 340 x 76
Bottom Seam Width 11.5 mm
Side Seam Width 12.8 mm
Top Seam Width 8.0 mm, 37 mm away from top edge
Average Tare Weight 61.1 grams
Average Gross Weight (as tested)
Iteration 1: 9.95 kg
Iteration 2: 523.5 grams
Iteration: 5.80 kg
Print EMI/STATIC SHIELD
Method of Closure
Test material was inserted into bag. Air was expelled from bag, then bag was
heat-sealed. Corners and top of the bag were folded against the sides (Refer to
Section 6.2)
Bag Width Bag Depth
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 5 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
INNER PACKAGING #2 – Reference Section 7 for drawings
STEEL PIPE ASSEMBLY [ITERATION 4 (001-UNI DET)]
Quantity 10
Style/Description Steel cylinder with screw on end caps
Supplier Romar
Part # DET-PIPE-001
Material of Construction SCH40 Black Steel
Minimum Thickness 3.68 mm
Nominal Thickness 3.80 mm
Dimension (mm, OD) 76.7 x 200 (closed)
Dimension (mm, OD) 60.5 x 152 pipe only
Dimension (mm, ID) 52.4 x 152 pipe only
Thread Height 27.8 mm on each end
Average Tare Weight 696.3 grams
Average Gross Weight 2722.5 grams
Average Net Weight 1205 grams
END CAPS
Quantity 20 (2 per pipe)
Part # DET-PIPE-002
Material of Construction SCH40 Black Steel
Dimension (mm, OD) 76.7 x 37.0
Dimension (mm, ID) 56.4 x 30.4
Average Tare Weight 410.6 grams
Test Material Steel pieces
Method of Closure Screwed on
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 6 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
INNER PACKAGING DETAIL #1-1 - Reference Section 7 for drawings
CORRUGATED TRAY [FOR ITERATION 1 (4 SLOT)]
Quantity 2
Style Tray with Locking Ends
Material 200# (42/26/42) Kraft/Kraft B-Flute Corrugate
Manufacturer/Supplier Danhil Container, Brownwood, TX
Part # 1313-PARTITION TRAY
File # 43736
Part # 1313-TRAY
Size (mm, OD) – set-up 335 x 335 x 50
Size (mm, ID) – set-up 320 x 320 x 45
Size (mm) flat 543 x 537
Caliper 3.07 mm
Average Tare Weight 146.0 grams
Average Gross Weight 9.85 kg
Method of Joining Panels Roll & Lock
Joint Locations Both Ends, bottom edges
Print None
Notes These corrugated trays were placed inside the
barrier bags, 1 tray per bag
INNER PACKAGING DETAIL #1-2 - Reference Section 7 for drawings
PARTITION SYSTEM [FOR ITERATION 1 (4 SLOT)]
Quantity 2
Material 275# (42/26/26/26/42) Kraft/Kraft BC-Flute
Corrugate
Manufacturer/Supplier Danhil Container, Brownwood, TX
Part # 1313-225 D/C 4 SLOT PRTN
File # 5797
Size (mm, OD) set-up 320 x 320 x 45
Caliper 6.81 mm
Average Tare Weight 96.5 grams
Notes
8 die-cut corrugated sheets (4 along and 4 across) interlock with each other to
form a 5 x 5 open-cell partition system. These partitions were placed inside the
corrugated trays
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 7 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
INNER PACKAGING DETAIL #1-3 - Reference Section 7 for drawings
DIE-CUT FOLDED CORRUGATED PAD
Quantity Iteration 1: 2
Iteration 2: 4
Material 275# (42/26/26/26/42) Kraft/Kraft BC-Flute
Manufacturer/Supplier All Star Corrugated, Fort Worth TX
Part # 1313-225B
Spec. # 1343
Size (mm, OD) folded 340 x 340 x 12
Caliper 6.58 mm
Average Tare Weight 203.5 grams
Location
Iteration 1: These die-cut folded in-half corrugated sheets were placed over the
steel cylinders/disks inside the corrugated trays into each barrier bag. Each side
contains 25 13.4 mm diameter die-cut openings
Iteration 2: These stacked folded die-cut pads were placed over the die-cut pads to
form the tray
INNER PACKAGING DETAIL #1-4 - Reference Section 7 for drawings
PLAIN CORRUGATED PAD
Quantity
Iteration 1: 0
Iteration 2: 2
Iteration 3: 2
Material 275# (42/26/26/26/42) Kraft/Kraft BC-Flute
Manufacturer/Supplier All Star Corrugated, Fort Worth TX
Part # 1313-104 WHS
Spec. # 113615
Size (mm, OD) flat 340 x 340
Caliper 6.38 mm
Average Tare Weight 104.5 grams
Location Iteration 2: 1 pad was placed under die-cut pads to form the tray
Iteration 3: Placed over the honeycomb pad
INNER PACKAGING DETAIL #1-5 - Reference Section 7 for drawings
DIE-CUT CORRUGATED INSERT [FOR ITERATION 2 (MEDIUM HOLE)]
Quantity 6 (3 per barrier bag)
Material 200# Kraft/Kraft BC-Flute Corrugate
Manufacturer/Supplier All Star Corrugated, Fort Worth TX
Part # 1313-425
Spec. # 71285
Size (mm, OD) flat 340 x 340
Caliper 6.38 mm
Weight 54.4 grams
Location These stacked die-cut pads were placed under the die-cut folded pads to form the
tray. Each pad contains 25 47.5 mm die-cut openings arranged 5 X 5
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 8 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
INNER PACKAGING DETAIL #1-6 - Reference Section 7 for drawings
HEXACOMB PAD [FOR ITERATION 3 (2 ½ HEX)]
Quantity 2
Material Hexacomb Core Type 3 light facing
Manufacturer/Supplier Pregis Hexacomb Corporation
Supplier All Star Corrugated, Fort Worth TX
Reference # J2V218A
Spec # J2V274
Size (mm, OD) flat 340 x 340
Caliper 76 mm
Average Tare Weight 224.2 grams
Location Inside each barrier bag. Each pad contains 25 40 mm diameter, 38 mm depth
opening arranged 5 X 5
INNER PACKAGING DETAIL #1-7 - Reference Section 7 for drawings
POLY-STRAPS
Quantity
Iteration 1: 6
Iteration 2: 4
Iteration 3: 4
Iteration 4: 0
Material Polypropylene
Manufacturer/Supplier Uline, Inc. Waukegan, IL
Item # S-1761
Length 775
Width 12.5 mm
Caliper 0.48 mm
Break Strength 300 lbs
Average Tare Weight 2.8 grams
Notes Each corrugated tray was strapped with 2 poly-
straps, 2 x 1 long way
Overall Inner Package Tare
Weight (IPTW)
Iteration 1:
IPTW1 = 2 X [61.1 + (2 x 146.0) + (2 x 96.5) + (3 x 2.8) + (2 x 203.5)]
IPTW1 = 2 X (61.6 + 292+ 193 + 8.4+ 407) = 2 X 962 = 1924.0 grams
Iteration 2:
IPTW 2 = 2 X [61.1 + (2 x 2.8) + (4 x 203.5) + (2 x 104.5) + (3 x 54.4)]
IPTW2 = 2 X (61.6 + 11.2 + 814 + 209 + 163.2) = 2 X 1259 = 2518.0 grams
Iteration 3:
IPTW3 = 2 X [61.1 + (2 x 2.8) + 104.5 + 224.2]
IPTW3 = 2 X (61.1 + 5.6 + 104.5 + 224.2) = 2 X 295.9 = 791.8 grams
Iteration 4:
IPTW4 = 10 X [696.3 + (2 x 410.6)] = 10 X (696.3 + 821.2)
IPTW4 = 10 X 1517.5 = 15,175 grams
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 9 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
PRODUCT SIMULANT/TEST MATERIAL #1
DUMMY LOAD 1 [ITERATION 1 (4 SLOT)]
Quantity 50 (25 per barrier bag)
Style/Description Solid steel disks
Dimension (mm, OD), D X H 53.5 x 62.9 (max height)
Dimension (mm, ID), D X H 44.1 x 50.8
Thickness 4.76
Average Gross Weight (as tested) 376.6 grams
Location Placed 5 X 5 within each corrugated trays
PRODUCT SIMULANT/TEST MATERIAL #1-1
ADDITIONAL DUMMY LOAD 1 [ITERATION 1 (4 SLOT)]
Quantity 2
Style/Description Zip-locked bags filled with steel powder
Average Gross Weight (as tested) 3.84 kg
Location Placed over the filled barrier bag, under top pad
PRODUCT SIMULANT/TEST MATERIAL #2
DUMMY LOAD 2 [ITERATION 2 (MEDIUM HOLE)]
Quantity 30 (30 over each barrier bag)
Style/Description Solid steel pieces with hole in center
Dimension (mm, ID), D X H 77.1 x 76.4
Thickness 9.2
Average Gross Weight (as tested) 423 grams
Location Placed over barrier bags
PRODUCT SIMULANT/TEST MATERIAL #3
DUMMY LOAD 3 [ITERATION 1 (2 ½ HEX)]
Quantity 50 (25 per barrier bag)
Style/Description Solid steel disks
Dimension (mm, OD), D X H 44.1 x 56.5 (max height)
Dimension (mm, ID), D X H 36.8 x 47.2
Thickness 3.96
Average Gross Weight (as tested) 215.3 grams
Location Placed 5 X 5 within each Hexacomb Pad
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 10 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
PRODUCT SIMULANT/TEST MATERIAL #3-1
ADDITIONAL DUMMY LOAD 3 [ITERATION 3 (2 ½ HEX)]
Quantity 4
Style/Description Zip-locked bags filled with steel powder
Average Gross Weight (as tested) 4.23 kg
Location Placed over the bottom layer barrier bag
PRODUCT SIMULANT/TEST MATERIAL #4
DUMMY LOAD 4 [ITERATION 4 (001-UNI DET)]
Quantity 300 (30 per pipe assembly)
Style/Description Solid steel curved pieces
Dimension (mm, ID), D X H 46.7 x 44.5
Thickness 1.6
Average Gross Weight (as tested) 40.16 grams
Location Placed over barrier bags
Overall Dummy Load Gross Weight
(DLGW)
Iteration 1:
IPTW1 = (50 x 0.376) + (2 x 3.84) = 18.8 + 7.68 = 26.48 kg
Iteration 2:
IPTW 2 = 60 x 423 = 25.38 kg
Iteration 3:
IPTW 3 = (50 x 0.0.215) + (4 x 4.23) = 10.76 + 16.95 = 26.48 kg
Iteration 4:
IPTW4 = 10 X (30 x 0.0401) = 10 X 1.2049 = 12.05 kg
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 11 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
OUTER PACKAGING - Reference Section 7 for drawings
FIBREBOARD BOX – UN 4G
Style Center Special Slotted Container (CSSC),
FEDCO Style: 0204
Manufacturer/Supplier All Star Corrugated, Fort Worth TX
Part # 1313-700 CHG BOX
File # 43703
Material of Construction Kraft/Kraft Vertical Corrugated, 40H Michelman outside with MRA
Dimension (mm, OD), L X W X H 353 x 353 x 208
Dimension (mm, ID), L X W X H 341 x 341 x 186 (Panel-To-Panel)
Stacking Height (mm) 208
Number of Walls - Flute Type Double-Wall BC-Flute
Tare Weight 685.1 grams
BMC (Box Marked Certification) 275#
Tested Basis Weight (lbs/1000ft²) 43.19 – 24.89– 28.59 – 24.32 – 43.35
Combined Weight (lbs/1000ft²) 115.13
Tested Burst Strength (lbs/inch²) 300.5
Tested Caliper 6.74 mm
Method of Joining Panels Glued inside
Mfr's Joint Flap Size 70 mm
Mfr's Joint Location 5-2 corner as per the ASTM diagram
Top Flap Gap/Meet Inner: Meet Outer: Meet
Bottom Flap Gap/Meet Inner: Meet Outer: Meet
Print None
BOX SEALING STAPLES (Refer to Section 6 for Closing Instruction and Section 7 for Specs)
Part # 3/4" C34 Stick Staples S-1396 Uline
Description 18 mm (3/4") long, 31 mm (1-1/4") crown
galvanized metal staples
Manufacturer/Supplier Uline, Inc. Waukegan, IL
Uline Item # S-1396
Quantity 8
Average Tare Weight 0.8 grams
Top Pattern 4 staples along the flap seam, 51 mm (2") away from boxes outside edges, 76
mm (3") apart on both sides & 100 mm (4") apart on center
Bottom Pattern 4 staples along the flap seam, 51 mm (2") away from boxes outside edges, 76
mm (3") apart on both sides & 100 mm (4") apart on center
Method of Closure See Section 7.2
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 12 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
OUTER PACKAGING DETAIL #1 - Reference Section 7 for drawings
PLAIN CORRUGATED PAD
Quantity
Iteration 1: 2
Iteration 2: 6
Iteration 3: 1
Iteration 4: 3
Material 275# (42/26/26/26/42) Kraft/Kraft BC-Flute
Manufacturer/Supplier All Star Corrugated, Fort Worth TX
Part # 1313-104 WHS
Spec. # 113615
Size (mm, OD) flat 343 x 338
Caliper 6.50 mm
Average Tare Weight 104.5 grams
Location
Iteration 2: 7 plain corrugated sheets were placed over and 1 below the barrier
bags
Iteration 3: 1 pad was placed over the barrier bags
Iteration 4: 1 pad was placed over and 2 below the pipe assemblies
OUTER PACKAGING DETAIL #2 - Reference Section 7 for drawings
HEXACOMB PAD [ITERATION 4 (001-UNI DET)]
Quantity 2
Material Hexacomb Core Type 4 light facing
Manufacturer/Supplier Pregis Hexacomb Corporation
Supplier All Star Corrugated, Fort Worth TX
Spec # H0687483
Size (mm, OD) flat 340 x 150
Caliper 51 mm
Average Tare Weight 95.5 grams
Location These honeycomb pads were placed against box inner walls
OUTER PACKAGING DETAIL #3 - Reference Section 7 for drawings
DIVIDER PAD [ITERATION 4 (001-UNI DET)]
Quantity 1
Material 275# Kraft/Kraft BC-Flute Corrugate
Manufacturer/Supplier All Star Corrugated, Fort Worth TX
Part # 1313-104 C SAW CUT
Spec. # 113615
Size (mm, OD) 343 x 239
Caliper 6.48 mm
Tare Weight 68.5 grams
Location Placed between 2 layers of pipe assemblies
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 13 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Overall Outer Package Tare Weight
(OPTW)
Iteration 1:
OPTW1 = [685.1 + (8 x 0.8)] + (2 x 104.5) = 691.5 + 209 = 905.0 grams
Iteration 2:
OPTW2 = [685.1 + (8 x 0.8)] + (6 x 104.5) = 691.5 + 627 = 1318.5 grams
Iteration 3:
OPTW3 = [685.1 + (8 x 0.8)] + 104.5 = 691.5 + 104.5 = 796.0 grams
Iteration 4:
OPTW4 = [685.1 + (8 x 0.8)] + (3 x 104.5) + (2 x 95.5) + 68.5 =
OPTW4 = 691.5 + 313.5 + 191 + 68.5 = 1264.5 grams
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 14 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
SECTION 3 – TEST DESCRIPTIONS & TEST RESULTS
Drop Test – 49 CFR 178.603
Test Specimen/Contents Characteristics -
Number of Packages Tested 20 (5 per iteration)
Product Specific Gravity 1.2
Packing Group Number PG II
State Solid
Dummy Load Steel disks or blocks
Drop Height Multiplier 0.67 for PG III; 1 for PG II & 1.5 for PG I
Drop Height Used 1.2 m
Conditioning Temperature & Duration, 49 CFR178.603(c) 24 Hours @ 73 °F & 50 % R.H.
Test Method -
The inner packagings were filled to 95% overflow capacity with solid load.
The packages were assembled as per closing instruction (Reference Section 6).
Assembled packages were dropped onto a solid steel plated concrete floor.
Drops were conducted within 60 seconds of removal of the assembled packages from the
conditioning chamber.
Test Results -
Drop /
Sample #
Test Weight
(kg) Box Orientation Results
1-1 29.52 Top (mfr's) corner
(Corner 1-2-5)
Box outside impact corner was slightly crushed around,
approximately 3" in diameter, however box was still in-tact
and capable and safe for further handling.
There was no leakage of the filling substance
1-2 29.39 Top surface (Face 1) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
1-3 29.39 Short side (Face 5) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
1-4 29.48 Long side (Face 2) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
1-5 29.39 Bottom surface (Face 3) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
Drop 1 –
Top Corner
Drop 2 –
Top Surface
Drop 3 –
Short Side
Drop 4 –
Long Side
Drop 5 –
Bottom Surface
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 15 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Drop Test Results (Continued) -
Drop /
Sample #
Test Weight
(kg) Box Orientation Results
2-1 29.48 Top (mfr's) corner
(Corner 1-2-5)
Box outside impact corner was slightly crushed around,
approximately 3" in diameter, however box was still in-tact
and capable and safe for further handling.
There was no leakage of the filling substance
2-2 29.48 Top surface (Face 1) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
2-3 29.39 Short side (Face 5) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
2-4 29.30 Long side (Face 2) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
2-5 29.39 Bottom surface (Face 3) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
Drop 1 –
Top Corner
Drop 2 –
Top Surface
Drop 3 –
Short Side
Drop 4 –
Long Side
Drop 5 –
Bottom Surface
3-1 29.57 Top (mfr's) corner
(Corner 1-2-5)
Box outside impact corner was slightly crushed around,
approximately 3" in diameter, however box was still in-tact
and capable and safe for further handling.
There was no leakage of the filling substance
3-2 29.39 Top surface (Face 1) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
3-3 29.48 Short side (Face 5) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
3-4 29.30 Long side (Face 2) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
3-5 29.30 Bottom surface (Face 3) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
Drop 1 –
Top Corner
Drop 2 –
Top Surface
Drop 3 –
Short Side
Drop 4 –
Long Side
Drop 5 –
Bottom Surface
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 16 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Drop Test Results (Continued) -
Drop /
Sample #
Test Weight
(kg) Box Orientation Results
4-1 30.64 Top (mfr's) corner
(Corner 1-2-5)
Box outside impact corner was slightly crushed around,
approximately 3" in diameter, however box was still in-tact
and capable and safe for further handling.
There was no leakage of the filling substance
4-2 28.48 Top surface (Face 1) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
4-3 28.84 Short side (Face 5) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
4-4 29.39 Long side (Face 2) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
4-5 30.39 Bottom surface (Face 3) There was no visible damage to the outer packaging, there
was no leakage of the filling substance
Drop 1 –
Top Corner
Drop 2 –
Top Surface
Drop 3 –
Short Side
Drop 4 –
Long Side
Drop 5 –
Bottom Surface
Drop Test Pass/Fail Criteria -
A package is considered to successfully pass the drop tests if for each sample tested:
For packaging containing liquid, there is no leakage of the filling substance from the inner packaging.
There is no damage to the outer packaging likely to adversely affect safety during transport.
Inner receptacles, inner packagings or articles must remain completely within the outer packaging.
Any discharge from a closure is slight and ceases immediately after impact or pressure equalization with no further
leakage.
No rupture is permitted in packagings for materials in Class 1 which would permit spillage of loose explosive
substances or articles from the outer packaging.
1 – Iteration 1 (4 Slot); 2 – Iteration 2 (MH-7); 3 - Iteration 3 (2 ½ HEX) & 4 – Iteration 4 (001-UNI DET)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 17 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Stacking Test - 49 CFR 178.606 (See Section 5.2 for Calculation)
Test Specimen/Contents Characteristics
Number of Packages Tested 12 (3 per iteration)
State Solid
Dummy Load Steel disks or blocks
Conditioning of Outer Packaging - 49 CFR 178.602(d) 24 Hours @ 73 °F & 50 % R.H.
Test Temperature 73 °F & 50 % R.H.
Test Method Free standing, static (dead weight) test
Test Duration 24 hours
Minimum calculated stacking test weight 331.8 kg (729.9 lbs) per package
Actual stacking test weight 347.3 kg (765 lbs) per package
Test Method -
The inner packagings were filled to 95% overflow capacity with solid load.
The packages were assembled as per closing instruction (Reference Section 6).
Stacking test load (dead weight) of 247.3 kg was applied individually to the top of the three (3) assembled packages per
each iteration using wood load spreaders and the weight was maintained for 24 hours.
Test Results -
Test Sample
#
Test Sample
Weight (kg)
Test Load
(Kg) Duration Stacking Test Results
1-6 29.39 347.3 24 Hours
Boxes did not show
any signs of
deterioration or
distortion, there was
no leakage of the
filling substance
1-7 29.48 347.3 24 Hours
1-8 29.30 347.3 24 Hours
2-6 29.27 347.3 24 Hours
Boxes did not show
any signs of
deterioration or
distortion, there was
no leakage of the
filling substance
2-7 29.30 347.3 24 Hours
2-8 29.60 347.3 24 Hours
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 18 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Stacking Test Results (Continued) -
Test Sample
#
Test Sample
Weight (kg)
Test Load
(Kg) Duration Stacking Test Results
3-6 29.75 347.3 24 Hours
Boxes did not show
any signs of
deterioration or
distortion, there was
no leakage of the
filling substance
3-7 29.57 347.3 24 Hours
3-8 30.20 347.3 24 Hours
4-6 29.30 347.3 24 Hours
Boxes did not show
any signs of
deterioration or
distortion, there was
no leakage of the
filling substance
4-7 30.48 347.3 24 Hours
4-8 30.60 347.3 24 Hours
Pass/Fail Criteria -
A package is considered to successfully pass the stack tests if for each sample tested:
No test sample shows any deterioration or distortion that could adversely affect safety during transport causing
instability in stacks of packages, or cause damage to inner packagings that is likely to reduce safety in transport.
There no leakage of the filling substance from the inner receptacle, or inner packaging.
1 – Iteration 1 (4 Slot); 2 – Iteration 2 (MH-7); 3 - Iteration 3 (2 ½ HEX) & 4 – Iteration 4 (001-UNI DET)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 19 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Vibration Test - 49 CFR 178.608
Test Specimen/Contents Characteristics -
Number of Packages Tested 12 (3 simultaneously, 3 per iteration) same samples used for
stacking test
State Solid
Dummy Load Steel cylinders wrapped around with plastic film
Conditioning of Outer Packaging - 49 CFR 178.602(d) 24 Hours @ 73 °F & 50 % R.H.
Test Temperature Ambient
Test Method ASTM D999-08 Rotary Motion Vibration
Test Duration 60 minutes
Test Frequency 235 CPM
Test Method -
The inner packagings were filled to 95% overflow capacity with solid load.
The packages were re-assembled as per closing instruction (Reference Section 6).
Three (3) assembled packages for each iteration were simultaneously placed on a rotary vibration table platform having
25.4 mm peak-to-peak displacement and vibrated in normal shipping orientation for one (1) hour at 235 CPM such that
a 1.6 mm thickness could be passed between the bottom of the samples and the platform. Immediately thereafter, the
packages were removed from the platform and turned on its side for examination.
Test Results -
Test Sample
#
Test Sample
Weight (kg)
Frequency
(CPM)
Duration
(Minutes) Vibration Test Results
1-6 29.39 235 60
There was no
rupture or
deterioration of
boxes, there was no
leakage of the filling
substance
1-7 29.48 235 60
1-8 29.30 235 60
2-6 29.27 235 60
There was no
rupture or
deterioration of
boxes, there was no
leakage of the filling
substance
2-7 29.30 235 60
2-8 29.60 235 60
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 20 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Vibration Test Results (Continued) -
Test Sample
#
Test Sample
Weight (kg)
Frequency
(CPM)
Duration
(Minutes) Vibration Test Results
3-6 29.75 235 60
There was no
rupture or
deterioration of
boxes, there was no
leakage of the filling
substance
3-7 29.57 235 60
3-8 30.20 235 60
4-6 29.30 235 60
There was no
rupture or
deterioration of
boxes, there was no
leakage of the filling
substance
4-7 30.48 235 60
4-8 30.60 235 60
Pass/Fail Criteria -
A package is considered to successfully pass the vibration test, if for each sample tested after it was immediately
removed from table platform and turned on its side:
There is no leakage or rupture from any of the packaging.
No test sample shows any deterioration which could adversely affect safety or container strength, during transport
liable to reduce packaging strength.
1 – Iteration 1 (4 Slot); 2 – Iteration 2 (MH-7); 3 - Iteration 3 (2 ½ HEX) & 4 – Iteration 4 (001-UNI DET)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 21 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Cobb (Water Absorption) Test - 49 CFR 178.516
Test Specimen/Contents Characteristics -
Number of Samples Tested 5
Test Duration 30 Minutes
Test Intensity 100 mL Distilled Water
Conditioning of Test Samples 24 Hours @ 73 °F & 50 % R.H.
Test Method - ISO International Standard 535-1976 (E), Cobb Method
Test Results -
Sample # #1 #2 #3 #4 #5 Average Results
grams/m² 126.5 122.2 123.9 116.4 122.4 122.2 Pass
Pass/Fail Criteria -
An increase in mass of greater than 155 grams/m² over the 30 minute duration of the tests represents an
unacceptable level of water absorption
SECTION 4 – SHIPPERS RESPONSIBILITY
It is the responsibility of the end shipper to determine authorization for use under these regulations.
It is the shippers responsibility to determine if the packaging is compatible for products to be shipped.
Use of the marking of this certification for any variations without further testing as allowed under US DOT 49
CFR Section 178.601 will be at complete responsibility of the shipper. By continuing to place the UN Markings
on Packagings, the packaging manufacturer or shipper is certifying that each packaging is constructed in the
same manner as the originally tested and certified packaging, and that each packaging is capable of withstanding
the prescribed performance tests.
According to 49 CFR Section 178.601 (1) Variation 1 - variations are permitted in inner packaging of a tested
combination packaging without further testing of the package, provided an equivalent level of performance is
maintained as described in 178.601 (1) Variation 4 (i),(A),(B),(C),(D),(E) and (F) and (ii).
According to US DOT 49 CFR Section 178.601 (e), the packaging manufacturer shall achieve successful test
results for the periodic retesting at intervals established by the manufacturer of sufficient frequency to ensure
that each packaging produced by manufacturer is capable of passing the design qualification test. Changes in
retest frequency are subject to the approval of the Associate Administrator for Hazardous Materials Safety. For
combination packaging, the periodic retest must be conducted at least once every 24 months.
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 22 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
SECTION 5 - CALCULATIONS
5.1 Certified Package Gross Mass Calculations Based on Test Level
Overall Inner Package Tare Weight (IPTW)
Iteration 1: 1924.0 grams
Iteration 2: 2518 grams
Iteration 3: 791.8 grams
Iteration 4: 15,175.0 grams
Overall Outer Package Tare Weight (OPTW)
Iteration 1: 900.5 grams
Iteration 2: 1318.5 grams
Iteration 3: 796 grams
Iteration 4: 1264.5 grams
Overall Dummy Load Gross Weight (DLGW)
Iteration 1: 26.48 kg
Iteration 2: 25.38 kg
Iteration 3: 27.71 kg
Iteration 4: 12.05 kg
Number of Inner Packaging (NIP)
Iteration 1: 2
Iteration 2: 2
Iteration 3: 2
Iteration 4: 10
Packing Group Number II
Minimum Package Weight as Tested (PGW)
Iteration 1: PGW1 = 29.30 kg
Iteration 2: PGW2 = 29.21 kg
Iteration 3: PGW3 = 29.30 kg
Iteration 4: PGW4 = 28.48 kg
Packing Group Multiplication Factor (PMF) 1.0
Formula for Calculating Certified Gross Mass
(CGW)
CGW = Minimum PGW
CGW = Minimum PGW4 = 28.48 kg
CGW = 23.7 kg
CGW = 23.7 kg (52.14 lbs)
(scaled down to match current marking)
Certified Package Marking Y = 23.7 (52.14 lbs)
5.2 Stacking Strength Test Calculations
Test Load (TL) TL = [(SH - PH) - 1] x CGW (static)
TL = [(SH - PH) - 1] x CGW x 1.5 (dynamic)
Overall Stacking Height of Packages (SH) 3000 mm (10 feet)
Overall Stacking Height of Package (PH) 208 mm
TL (Static)
TL = [(3000/208) - 1] x 23.7 = 14 (rounded up) x 23.7
TL = 331.8 kg (729.9 lbs)
Rounded up to at 347.3 kg (765 lbs) per package for test purposes
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 23 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Appendix A – Regulatory & Industry Standard References
Regulatory Standard References:
Test 1. 2. 3. 4. 5.
49 CFR UN Regulation IMDG ICAO IATA
Drop Test 178.603 6.1.5.3 6.1.5.3 6.4.3 6.3.3
Stacking Test 178.606 6.1.5.6 6.1.5.6 6.4.6 6.3.6
Hydrostatic
Pressure 173.27(c) 4.1.1.4 4.1.1.4 4.1.1.6 5.0.2.9
Cobb Test 178.516 6.1.4.12.1 6.3.11.1 6.2.12.2
Vibration Test 178.608 - - 4.1.1.1 5.0.2.7
1. United States Code of Federal Regulations (CFR), Title 49, Transportation, Parts 100-199
2. The United Nations Recommendations on The Transport of Dangerous Goods – Model Regulations (Orange
Book)
3. International Maritime Dangerous Goods Code (IMDG)
4. Technical Instructions for the Safe Transport of Dangerous Goods by Air (ICAO)
5. International Air Transport Association (IATA), Dangerous Goods Regulations
Industry Standard References:
Drop Test ASTM D5276 Standard Test Method for Drop Test of Loaded Containers by Free Fall
Stacking Test ASTM D4577 Standard Test Method for Compression Resistance of a Container Under Constant
Load
Hydrostatic
Pressure ASTM D7660
Standard Guide for Conducting Internal Pressure Tests on United Nations (UN) Packagings
Cobb Test ISO 535 Paper and Board – Determination of Water Absorption – Cobb Method
Vibration Test ASTM D999 Standard Test Method for Vibration Testing of Shipping Containers
American Society for Testing and Materials (ASTM) International Organization for Standardization (ISO)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 24 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Appendix B – Test Equipment & Instrumentation
No. Test Machine, Model # and Serial # Capacity Calibration
Date
Re-Calibration
Date
1. Drop Table, Lansmont Corporation:
Model #PDT-56-ED; Serial #M-1245 11" ÷ 72" 2/22/2019 2/22/2020
2. Drop Table, Gaynes Eng. Inc., Serial #G-13673-2 12" ÷ 120" 2/22/2019 2/22/2020
3. Vibration Table, Gaynes Eng. Inc.: Model #6000V 3000 lbs 2/22/2019 2/22/2020
4. Compression Machine, TechLab Systems:
Model #Validator; S/N #1005971T078 5000 lbs 2/22/2019 2/22/2020
5. VWR Traceable Digital Thermometer:
Serial #51234531 (for Conditioning, Freezer), -58° ÷ 302° F 2/13/2019 2/13/2020
6. AMETEK Digital Thermometer: Model #DT-8350 -50° ÷ 450° F 2/22/2019 2/22/2020
7. Paperless Temperature & Humidity Recorder, Dickson:
Model #TH660 (for Cold Chamber) -148° ÷ 350° F 2/22/2019 2/22/2020
8. Paperless Temperature & Humidity Recorder, Dickson:
Model #TH635 (for Conditioning Room)
-140° ÷ 185° F,
0% ÷ 95% RH 2/22/2019 2/22/2020
9. Thermometer & Hygrometer,
Omega Engineering: Model #RH520 (for Hot Chamber)
-20° ÷ 140° F,
10% ÷ 95% RH 2/22/2019 2/22/2020
10. Bench Scale, SeiKo Scale Division:
Model #WA200001XP; S/N #160808009 10mg ÷ 20 kg 5/16/2019 5/16/2020
10. Mettler Toledo D-72458 Albstadt:
Model #BBK-462-35ST; S/N #2986871-7CK 0 ÷ 35 kg 4/19/2019 4/19/2020
11. Mettler Toledo D-72458 Albstadt:
Model #XS16001L; S/N #B112123112 0 ÷ 16.1 kg 4/19/2019 4/19/2020
12. Analytical Balance, PCA, Germany:
Model #AB200; S/N #2626 10mg ÷ 200 g 5/16/2019 5/16/2020
13. Bench Scale, Ohaus: Serial #5040335-5XZ 0 ÷ 200 lbm 5/16/2019 5/16/2020
14. Caliper, Fowler: Model #54-100-112-1 ;
S/N: 1205A58182 0 ÷ 12" 5/16/2019 5/16/2020
15. Mitutoyo Cor. Micrometer:
Model #Absolute Digimatic CD-8C; S/N: 4934 0 ÷ 6" 5/16/2019 5/16/2020
16. Electronic Torque-Meter, Kaps-All:
Model #EB-650; S/N #11051 3 ÷ 100 inch-lbs 4/19/2019 4/19/2020
17. Toque Wrench, CDI, Model No. 301LDIN 0 ÷ 30 inch-lbs 5/16/2019 5/16/2020
18. Omega Digital Pressure Gauge:
Model #DPG7010-200; S/N #1305276 0 ÷ 200 psi 5/15/2018 5/15/2019
19. Omega Digital Pressure Gauge:
Model #DPG8001-30V30; S/N #16121406000 -30" ÷ 30 psi 2/13/2019 2/13/2020
20. Winters Pressure Gauge, WG2-6 0 - 60 psi 5/16/2019 5/16/2020
21. Ashcroft Pressure Gauge, V/300 Psi
Model #DG 25: S/N #16080906005 -30 - 300 psi 10/21/2018 10/21/2019
22. The Mullen Tester, B.F Perkins and Son: Serial #14047 0 ÷ 800 psi
0 ÷ 300 psi 5/16/2019 5/16/2020
23 The Mullen Tester, B.F Perkins and Son: Serial #2180 0 ÷ 800 psi
0 ÷ 1500 psi 5/16/2019 5/16/2020
24. ECT Tester, Testing Machines, Inc.: S/N #13748 0 ÷ 120 lbs 5/16/2019 5/16/2020
25. Measuring Tape, Ultra-Touch: ANAMA TM1 & TM2 0 ÷ 25 Feet 5/16/2019 5/16/2020
26. Measuring Tape, Stanley Power Lock, 33-425;
ANAMA TM3 0 ÷ 25 Feet 5/16/2019 5/16/2020
27. Measuring Tape, Made In China; ANAMA TM4 0 ÷ 25 Feet 5/16/2019 5/16/2020
28. Presto Dart Impact Tester, Model No. PDI-350;
S/N: 2010167076 21" ÷ 1.7 feet 2/22/2019 2/22/2020
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 25 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
SECTION 6 – PACKAGING ASSEMBLY (CLOSING) INSTRUCTIONS
Section 6.1 - Testing Laboratory Closing Instructions:
Note: Packages were received assembled.
ITERATION 1 (4 SLOT) - Step-By-Step Packaging Assembly Demonstration
Articles Corrugated Tray Installation of Partition
System into Tray
Installation of Articles into
Tray
Installation of Top Pad over
Articles
Poly-Strapping Method of
Filled Tray
Poly-Strapping Method of
Filled Tray
Installation of Poly-Strapped
Tray into Barrier Bag
Barrier Bag Closing/Sealing
Method Sealed Barrier Bags Outer Box Closure Pattern Erected Outer Box
Installation of Bottom Pad
into Outer Box
Installation of Bottom Layer
Barrier Bag into Outer Box
Installation of Bottom Layer
Barrier Bag into Outer Box
Installation of Additional
Weight into Outer Box
Installation of Top Pad into
Outer Box Closed Outer Box Top View
Closed Outer Box Top/Side
View
Closed Outer Box
Bottom/Side View
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 26 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) - Step-By-Step Packaging Assembly Demonstration
Poly-Strapping Method of
(Filled) Tray
Poly-Strapping Method of
(Filled) Tray
Installation of Poly-
Strapped Tray into
Barrier Bag
Barrier Bag
Closing/Sealing Method
Sealed Barrier Bags Outer Box Closure
Pattern Erected Outer Box
Installation of Bottom
Pads into Outer Box
Installation of Bottom
Layer Barrier Bag into
Outer Box
Installation of Layer Pad
over Barrier Bag into
Outer Box
Installation of Dummy
Load over Bottom Layer
Pad
Installation of Layer Pad
over Bottom Layer
Dummy Load into Outer
Box
Installation of Top Layer
Barrier Bag into Outer
Box
Installation of Layer Pad
over Barrier Bag into
Outer Box
Installation of Dummy
Load over Top Layer Pad
Installation of Top Pad
into Outer Box
Closed Outer Box Top View Closed Outer Box Bottom/Side
View Closed Outer Box Bottom View
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 27 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) - Step-By-Step Packaging Assembly Demonstration
Articles Installation of Articles
into Hexacomb Pad
Installation of Top Pad
over filled Hexacomb Pad
Poly-Strapping Method of
Filled Hexacomb Pad
Poly-Strapping Method of
Filled Hexacomb Pad
Installation of Poly-
Strapped Hexacomb Pad
into Barrier Bag
Barrier Bag
Closing/Sealing Method Sealed Barrier Bags
Outer Box Closure
Pattern Erected Outer Box
Installation of Bottom
Layer Barrier Bag into
Outer Box
Installation of Assittional
Weight over Bottom
Layer Bag into Outer Box
Installation of Top Layer
Barrier Bag into Outer
Box
Installation of Top Pad
into Outer Box
Closed Outer Box Top
View
Closed Outer Box Bottom
View
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 28 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) - Step-By-Step Packaging Assembly Demonstration
Articles Outer Box Closure
Pattern Erected Outer Box
Installation of Bottom
Pad into Outer Box
Installation of Side
Hexacomb Pads
Installation of Bottom
Layer Articles into Outer
Box
Installation of Divider
Pad over Articles
Installation of Top Layer
Articles into Outer Box
Installation of Top Pad
into Outer Box
Closed Outer Box Top
View
Closed Outer Box Bottom
View
Closed Outer Box
Bottom/Side View
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 29 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Section 6.2 - Manufacturer’s Closing Instructions:
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 30 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 31 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 32 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 33 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 34 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 35 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 1 (4 SLOT) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 36 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 37 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 38 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 39 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 40 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 41 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 42 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 43 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 2 (MEDIUM HOLE) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 44 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 45 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 46 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 47 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 48 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 49 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 50 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 3 (2 ½ HEX) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 51 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 – CLOSING INSTRUCTION
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 52 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 53 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 54 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 55 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 56 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 57 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
ITERATION 4 (001-UNI DET) – CLOSING INSTRUCTION (CONTINUED)
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 58 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
SECTION 7 – PACKAGING COMPONENTS SPECIFICATION & DRAWING
Manufacturer’s List of Suppliers
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 59 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Barrier Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 60 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Barrier Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 61 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Corrugated Tray Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 62 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Corrugated 4 Slot Partition Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 63 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Corrugated 4 Slot Partition Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 64 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Corrugated Die-Cut Folded Pad Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 65 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Hexacomb Pad Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 66 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Corrugated Perforated Pad Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 67 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Poly-Strap Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 68 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Hexacomb Pad Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 69 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Hexacomb Pad Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 70 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Outer Box Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 71 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Plain Pad Drawing & Specification
Owen Oil Tools, Inc.
Certification #+CM0428
Date of Report: 6/19/2019
Periodic Retest Date: 6/19/2021
Page 72 of 72
____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
CA2013040016 Project #2477
Carton Sealing Staples Specification