A G R I C U LT U R A L
15T. +34 981 695 074F. +34 981 695 232
Anxeriz - 15684 Tordoia - A Coruña (SPAIN)[email protected]
www.tmccancela.com
NEW AGRICULTURAL AND FORESTRY AGE
U N I Q U E
E F F I C I E N T
S T R O N G
D I F F E R E N T
I N N O V AT I V E
4
50
MULCHERS
ROTARY BRUSH CUTTERS
82
90
94
LOG SPLITTERS
COMPLEMENTS
ANNEXES
ale (HIGH STReNGTH STeel)The steel has two main parts in their behavior, the elastic and plastic. The elastic part is a steel enabling a deformation and subjecting this to recover its initial properties. When we apply a force in the steel and it crosses the line between elastic and plastic, it will be deformed permanently. Each steel has a load value in the passing of the elastic to the plastic zone. The high strength steels have a high values in this load. The A.L.E. cold forming steel has a yield stress value (point from which appears the deformation), which duplicates the value of a traditional steel. TMC Cancela incorporates A.L.E. steel in the frame of its machines to provide an extra quality, avoiding cracks and breaks in the most demanding working conditions.
Hdx (WeaR ReSISTaNT STeel)It’s a steel that has in its composition many elements which give excellent properties against abrasion and wear without compromising important steel factors such as bending and welding. The wear-resistant values increase steel double lifetime with respect to traditional steel. Wear-resistant TMC Cancela steels incorporate all the elements that are in direct contact with the ground, such as skates, plates, inner shells and counterblades.
fTS (faN TRaNSMISSION SYSTeM)System of refrigeration incorporated in the pulleys of the mulchers in order to evacuate the heat of the pulleys and drive transmission during the operation.
dUal SpeedSystem that allows to change the input speed configuration in the gearbox interchanging the position of the pulleys. With this system we can work with different tractors and change quickly the input speed in the machine. With PTO to 540 rpm we get a leverage ratio in the pulleys (the bigger pulley is the drive one). With 1.000 rpm input we need a reduction ratio for obtaining the same rotor speed. In this case the drive pulley is the small one. This system ensures the work with any type of tractor and switch from one speed input to another quickly.
WIdeST Patented side openings in rotary brush cutter skids for maximum utilization of working width of the machine. At the same time a better mulching of the material is ensured due to the blockage in the cavity created in the opening “window”.
eSb (exTeRNal SHafT beaRING)Built-in system applied to the side extension shafts of the gearbox and drive lines. The bearing of of the transmission extension is positioned on the side of the frame ensuring a very close distance between the pulley and this bearing, reducing dramatically the bending in the shaft. This will increases the life of the shaft, reduce the bearing loads and consequently also decrease the temperature in the drive line.
bOlTOpSystem for assemblying the hammers to the rotor with special socket connection between bolts and lugs. The bolt head is completely embedded into the lug and ensures a precise fit, preventing rotation and loosening. The bolts are 10.9 quality and Ø27 mm with lock nut. This is the most robust assembly system in the market for swinging hammers, ensuring no bolts breakage and avoiding downtimes during work.
zMZero Maintenance patented system, built at the joint between central and lateral gearboxes of agricultural and forestry rotary brush cutters. Ensures zero maintenance on connections through a special adjustment joint between two grooved tapered shafts.
flOaTDamping system incorporated in the three point hitch of the agricultural mulchers with lateral parallelogram displacement, which enables the decoupling of the tractor linkage and the adaptation of the machine to the ground. This system eliminates the traditional bolt joint which was very problematic and created many breaks and deformations. This new system allows to built a three point hitch much more robust according to expectations and demands of the machine. A double advantage is obtained with this device: acts as a damping system and reduces the impact on the frame of the machine and on the tractor lifting arms, especially when driving at high speed during transport by roads.
SIdeSTepSystem for overcoming obstacles on the sides of forestry and agricultural mulchers. The pulleys surround plates are rigid and the reinforcement fairings make a wedge effect ensuring the lateral rigidity while avoiding obstacles snagging during work. This system reinvented traditional caps that did not act like a real protection, only made the barrier function between pulleys and the environment, but the impacts in some cases bended the cover causing serious problems to the drive line. With the Sidestep, the impacts to the sideways of the machines translate into simple happenings of daily work without any inconvenience to the integrity of the drive line.
flOW UpFlow Up is a cutting system consisting in blades with flaps that cause a suction of the material (grass, low brush…) in the back part of the cutting area, ensuring a better and cleaner cut. These blades are assembled to concave plate with bolts and bushes. The special shape of the rotor ensures optimum sliding as close to the ground as possible without damaging the topsoil. Assembled in the range of rotary brush cutters intended for green spaces, large areas and farming works.
TMC
SYST
EMS
MOd. 85 90 110
120
130
140
150
160
170
180
190
200
210
220
240
250
280
300
320
540
580
pg.
TP • • • • • • • • 30-75 06
TPS • • • • • • 45-75 08
TG • • • • • 50-90 10
TGS • • • • • 50-100 12
TMS • • • • • • • 60-200 14
TMD • • • • • 100-200 16
TGH • • • • • 50-90 18
TMH • • • • • • 60-200 20
TH • • • • • • • • 50-200 22
TH2 • 150-200 22
THP • • 150-360 24
TJL • • • • • 90-200 26
TJL2 • • 160-200 26
TJ • • • • • 80-200 28
TJ2 • • 200 28
TJS • • 150-300 30
TV • • • • • • 35-100 32
TO • • • • • 60-115 34
TVS • • • • • • 60-100 36
TVC • • • • 70-110 38
TOS • • • 90-200 40
TPT • • • • 80-200 42
TDS • • • • • 65-100 44
TDR • • • • • 70-200 46
TDE • • • 110-200 48
85 90 110
120
130
140
150
160
170
180
190
200
210
220
240
250
280
300
320
540
580
CV
cmWORKING WIdTH
MULCHERS
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 76
00 0000
MOD. TP-090 TP-110 TP-120 TP-140 TP-160 TP-180 TP-200 TP-220
TECHNICAL FEATURES
Working width (m) 0,90 1,10 1,20 1,40 1,60 1,80 2,00 2,20
Total width (m) 1,12 1,32 1,42 1,62 1,82 2,02 2,22 2,42
Required input power (CV) 30 40 45 50 55 65 70 75
Max. allowed power (CV) 60
Rotor/s cutting diameter (mm) 383,7
Gearbox input speed (rpm) 540
Nr. of hammers a01 14 16 18 22 26 28 32 34
Nr. of blades a03 42 48 54 66 78 84 96 102
Counterblades 2 replaceable rows
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 4-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type G5
fix model weight (kg) 292 326 364 398 432 466 500 545
Shifting model weight (kg) - 355 412 468 478 494 529 569
Hydraulic cylinder stroke (mm) - - 300 400 400 400 400 400
Working reach
mechanical 1 (mm) 450-450 550-550 600-600 700-700 800-800 900-900 1.000-1.000 1.100-1.100
mechanical 2 (mm) - 430-670 450-750 540-860 650-950 720-1.080 810-1.190 910-1.290
hydraulic (mm) - - 719,5-780,5 769,5-1.030,5 869,5-1.130,5 869,5-1.330,5 869,5-1.530,5 869,5-1.730,5
REF. FIX MODEL HM1Z09 HM1Z11 HM1Z12 HM1Z14 HM1Z16 HM1Z18 HM1Z20 HM1Z22
REF. SHIFTING MODEL HM2Z12 HM2Z14 HM2Z16 HM2Z18 HM2Z20 HM2Z22
OPTIONS
035 Rotor assembled with blades
132 Gearbox until 90 CV
233 Roller scraper
030 Gearbox with double free wheel on shifting models (for reversible work position) and double linkage head
KM1.A01.1Z Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.1Z Maintenance kit (basic kit + 4 belts XPB) KM1.A03.1Z Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.1Z Maintenance kit (basic kit + 4 belts XPB)
09
Ø 60 mm
B E L T Sx4
01 Body with double position of latching (fix model).
02 Protection at front with metallic plates.
03 Sliding skids.
04 External rear roller for ground adjustment.
05 Shifting three point linkage with an hydraulic cylinder (shifting model).
06 Rotor with floating hammers assembled to the rotor with bolts of 20 mm diameter.
07 Transmission with 4 belts.
08 Gearbox with a free wheel and with an input of 540 rpm and with a drive
shaft of 1”3/8 Z6.
09 Replaceable counterblades TMC Cancela model C01.
10 Sidestep system on frame sides.
11 Rear picks.
TP
A01
A03
04 080302
05 01
03
10
11
04
05
02
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 98
00
MOD. TPS-120D TPS-140D TPS-160D TPS-180D TPS-200D TPS-220D
TECHNICAL FEATURES
Working width (m) 1,20 1,40 1,60 1,80 2,00 2,20
Total width (m) 1,42 1,62 1,82 2,02 2,22 2,42
Required input power (CV) 45 50 55 65 70 75
Max. allowed power (CV) 90
Rotor/s cutting diameter (mm) 383,7
Gearbox input speed (rpm) 540
Nr. of hammers a01 18 22 26 28 32 34
Nr. of blades a03 54 66 78 84 96 102
Counterblades 2 replaceable rows
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 4-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type G5
Weight (kg) 435 492 540 595 655 705
Hydraulic cylinder stroke (mm) 300 400 400 400 400 400
Working reach hydraulic (mm) 719,5-780,5 769,5-1.030,5 869,5-1.130,5 869,5-1.330,5 948,5-1.632,5 869,5-1.832,5
REF. MOD. HM7W12 HM7W14 HM7W16 HM7W18 HM7W20 HM7W22
OPTIONS
035 Rotor assembled with blades
233 Scraper on rear roller
KM1.A01.7W Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease)
KM2.A01.7W Maintenance kit (basic kit + 4 belts XPB) KM1.A03.7W Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.7W Maintenance kit (basic kit + 4 belts XPB)
Ø 60 mm
B E L T Sx4
01 Body built in high strength steel and with
an hydraulic shifting three point linkage.
02 Rear hood with opening adjustment.
03 Sliding skids.
04 External rear roller with adjustment on height.
05 Rotor with floating hammers assembled to the rotor with bolts of 20 mm
diameter.
06 Protection at front with metallic plates.
07 Transmission with 4 belts.
08 Gearbox with a free wheel and with an input of 540 rpm and with a drive
shaft of 1”3/8 Z6.
09 Replaceable counterblades TMC Cancela model C01.
10 Lateral deflector and rounded shell to avoid snagging.
11 Rear picks.
TPS
A01
A03
1104 09
03
02
04
11
01
10
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 1110
00 0000
MOD. TG-130 TG-160 TG-180 TG-200 TG-220
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20
Total width (m) 1,50 1,80 2,00 2,20 2,40
Required input power (CV) 50 60 70 80 85
Max. allowed power (CV) 90
Rotor/s cutting diameter (mm) 428,3
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a02 10 14 16 18 20
Counterblades 1 replaceable row + 3 fix rows
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 4-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type G8
fix model weight (kg) 567 620 714 776 910
Shifting model weight (kg) 664 710 781 852 976
Hydraulic cylinder stroke (mm) 250 500 500 600 600
Working reach
mechanical 1 (mm) 650-650 800-800 900-900 1.000-1.000 1.100-1.100
mechanical 2 (mm) - 600-1.000 600-1.200 700-1.300 700-1.500
hydraulic (mm) 775-525 1.027,5-1.072,5 1.023,5-1.276,5 1.192,5-1.407,5 1.198,5-1.601,5
REF. FIX MODEL HM3Z13 HM3Z16 HM3Z18 HM3Z20 HM3Z22
REF. SHIFTING MODEL HM4Z13 HM4Z16 HM4Z18 HM4Z20 HM4Z22
OPTIONS
141 Picks for rake
233 Roller scraper
135 Configuration with a gearbox input of 1.000 rpm
024 Rubber protection at both front and rear
KM1.A02.3Z Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A02.3Z Maintenance kit (basic kit + 4 belts XPB)
option 141
Ø 80 mm
B E L T Sx4
01 Body with double position of latching (fix model).
02 Protection at front with metallic plates.
03 Protection skids.
04 Rear roller at inside position for ground adjustment.
05 Shifting three point linkage with an hydraulic cylinder (shifting model).
06 Rotor with floating hammers assembled to the rotor with bolts
of 20 mm diameter.
07 Transmission with 4 belts.
08 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Replaceable counterblades TMC Cancela model C01.
TG
A02
02 0403
06
03
04
02
09
01
09
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 1312
00
MOD. TGS-130D TGS-160D TGS-180D TGS-200D TGS-220D
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20
Total width (m) 1,52 1,82 2,02 2,22 2,42
Required input power (CV) 50 60 70 80 85
Max. allowed power (CV) 100
Rotor/s cutting diameter (mm) 436
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 12 16 18 20 22
Counterblades 1 replaceable row + 3 fix rows
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 5-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type G8
Weight (kg) 764 810 882 952 1.076
Hydraulic cylinder stroke (mm) 250 500 500 600 600
Working reach shifting reversible model (mm) 775-775 1.027,5-1.072,5 1.042,5 -1.257,5 1.192,5-1.407,5 1.192,5-1.607,5
REF. MOD. HM0V13 HM0V16 HM0V18 HM0V20 HM0V22OPTIONS
141 Picks for rake
028 Gearbox with double free wheel (reversible working position)
024 Rubber protection at both front and rear
259 Protection at front with chains
233 Roller scraper
135 Configuration with a gearbox input of 1.000 rpm
KM1.A04.0V Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.0V Maintenance kit (basic kit + 5 belts XPB)
Ø 100 mm
B E L T Sx5
01 Body built in high strength steel and with a reversible hydraulic shifting three
point linkage.
02 Protection at front with metallic plates or chains (in option).
03 Protection skids.
04 Rear roller at inside position for ground adjustment.
05 Rotor with floating hammers assembled to the rotor with bolts of 27 mm
diameter (Boltop system).
06 Transmission with 5 belts.
07 Gearbox with free wheel with a drive shaft of 1”3/8 Z6 (through shaft in
shifting models).
08 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system)
09 Replaceable counterblades TMC Cancela model C01.
TGS
A04
04 option 141
0601
03
04
02
09
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 1514
MOD. TMS-130 TMS-160 TMS-180 TMS-200 TMS-220 TMS-250 TMS-300
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20 2,50 3,00
Total width (m) 1,50 1,80 2,00 2,20 2,40 2,70 3,20
Required input power (CV) 60 70 90 100 115 135 150
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 489
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 12 16 18 20 22 26 30
Counterblades 2 replaceable rows
Coupling category Cat. 2 / Cat. 3
Nr. of belts - type 6-xpb
Skids Sliding adjustables (2 positions)
adjustable height control Skids and roller
pTO Shaft bondioli type 108
fix model weight (kg) 720 816 884 952 1.020 1.122 1.292
Shifting model weight (kg) - 1.049 1.124 1.207 1.295 1.406 1.674
Hydraulic cylinder stroke (mm) - 300 300 500 600 700 700
Working reach hydraulic (mm) - 832,5-1.057,5 1.032,5-1.257,5 1.032,5-1.457,5 1.157,5-1.632 1.527,5-1.942,5 1.777,5-2.192,5
REF. FIX MODEL HM4T13 HM4T16 HM4T18 HM4T20 HM4T22 HM4T25 HM4T30
REF. SHIFTING MODEL HM0T16 HM0T18 HM0T20 HM0T22 HM0T25 HM0T30
OPTIONS
P03 Internal shell reinforced with wearing resistant steel with replaceable counterblades
030 Gearbox with double free wheel(only in shifting models)
091 Removable light panels
234 Picks for rake
024 Rubber protection at both front and rear
233 Roller scraper
135 Configuration with a gearbox input of 1.000 rpm
KM1.A04.4T Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.4T Maintenance kit (basic kit + 6 belts XPB)
Ø 125 mm
B E L T Sx6
TMS
A04
01 Body with fix three point linkage and completely built in high strength steel.
02 Protection at front with chains.
03 Sliding skids.
04 Rear roller at inside position with height adjustment for ground adjustment.
05 Reversible shifting three point linkage with an hydraulic cylinder
(shifting model).
06 Rotor with floating hammers assembled to the rotor with bolts of 27 mm
diameter (Boltop system).
07 Transmission with 6 belts.
08 Gearbox with free wheel with a drive shaft of 1”3/4 Z6 (through axle system
on shifting models).
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Replaceable counterblades TMC Cancela model C01.
1004 0605
02
01
03
04
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 1716
00 0000 00
MOD. TMD-160 TMD-180 TMD-200 TMD-220 TMD-250
TECHNICAL FEATURES
Working width (m) 1,60 1,80 2,00 2,20 2,50
Total width (m) 1,85 2,05 2,25 2,45 2,75
Required input power (CV) 80 90 100 115 120
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 489
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 16 18 20 22 26
Counterblades 3 replaceable rows + 1 fix row
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 6 - xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type 108
Weight (kg) 840 895 955 1.105 1.170
Hydraulic cylinder stroke (mm) 900 900 900 1.000 1.000
Working reachhydraulic 1 (mm) 1.015,5-1.484,5 1.015,5-1.684,5 1.015,5-1.884,5 1.015,5-2.184,5 1.015,5-2.484,5
hydraulic 2 (mm) 665-1.835 665-2.035 665-2.235 665-2.535 665-2.835
REF. MOD. HM1T16 HM1T18 HM1T20 HM1T22 HM1T25
OPTIONS
024 Rubber protection at both front and rear
135 Configuration with a gearbox input of 1.000 rpm
233 Roller scraper
248 Lateral control wheel
P03 Internal shell reinforced with wearing resistant steel with replaceable counterblades
KM1.A04.1T Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.1T Maintenance kit (basic kit + 6 belts)
09
Ø 125 mm
B E L T Sx6
01 Body built in high strength steel with an hydraulic shifting
three point linkage.
02 Protection at front with chains.
03 Protection skids.
04 External rear roller for ground adjustment.
05 Reversible shifting three point linkage with an hydraulic cylinder
(shifting model).
06 Rotor with floating hammers assembled to the rotor with bolts of 27 mm
diameter (Boltop system).
07 Transmission with 6 belts.
08 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Replaceable counterblades TMC Cancela model C01.
TMD
A04
MAXIMUM DISPLACEMENT
02 04 05 08
01
05
03
02
04
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 1918
MOD. TGH-130 TGH-160 TGH-180 TGH-200 TGH-220
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20
Total width (m) 1,55 1,85 2,05 2,25 2,45
Required input power (CV) 50 60 70 80 85
Max. allowed power (CV) 90
Rotor/s cutting diameter (mm) 412,3
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a01 20 26 28 32 34
Nr. of blades a03 60 78 84 96 102
Nr. of hammers a04 12 16 18 20 22
Counterblades 2 replaceable rows
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 4-xpb
Skids adjustable bolted (2 positions)
adjustable height control Rear roller
pTO Shaft bondioli type G8
Weight (kg) 594 642 730 802 858
Working reach mechanical (mm) 602,5-732,5 725,5-882,5 852,5-982,5 952,5-1.082,5 1.052,5-1.182,5
REF. FIX MODEL HM5T13 HM5T16 HM5T18 HM5T20 HM5T22
OPTIONS
135 Configuration with a gearbox input of 1.000 rpm
252 Rotor with hammers TCM27 with Boltop system
035 Rotor assembled with blades
KM1.A02.5T Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A02.5T Maintenance kit (basic kit + 4 belts XPB) KM1.A03.5T Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.5T Maintenance kit (basic kit + 4 belts XPB) KM1.A04.5T Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.5T Maintenance kit (basic kit + 4 belts XPB)
Ø 80 mm
TGHB E L T Sx4 A0
3
01 Body with fix three point linkage.
02 Protection at front with chains.
03 Sliding skids.
04 Hydraulic hood with 2 hydraulic cylinders and an external roller
incorporated on hood.
05 Rotor with floating hammers assembled to the rotor with bolts
of 20 mm diameter.
06 Transmission with 4 belts.
07 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
08 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
09 Replaceable counterblades TMC Cancela model C01.
03 04
03
07
01
02
A01
A04
04
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 2120
00
MOD. TMH-130 TMH-150 TMH-160 TMH-180 TMH-200 TMH-220
TECHNICAL FEATURES
Working width (m) 1,30 1,50 1,60 1,80 2,00 2,20
Total width (m) 1,60 1,70 1,80 2,00 2,20 2,40
Required input power (CV) 70 80 90 100 115 120
Max. allowed power (CV) 150
Rotor/s cutting diameter (mm) 489
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 12 16 16 18 20 22
Counterblades 2 replaceable rows
Coupling category Cat. 2
Nr. of belts - type 6-xpb
Skids adjustable bolted (2 positions)
adjustable height control Roller (3 positions) / Skids (2 positions)
pTO Shaft bondioli type 108
fix model weight (kg) 714 782 816 884 952 1.020
Shifting model weight (kg) 850 892 916 988 1.056 1.158
Hydraulic cylinder stroke (mm) - 250 300 300 500 600
Working reachmechanical 1 (mm) 650-650 750-750 800-800 900-900 1.000-1.000 1.100-1.100
hydraulic (mm) - 782,5-957,5 832,5-1.057,5 1.032,5-1.257,5 1.032,5-1.457,5 1.157,5-1.633
REF. FIX MODEL HM9Z13 HM9Z15 HM9Z16 HM9Z18 HM9Z20 HM9Z22
REF. SHIFTING MODEL HM0Z15 HM0Z16 HM0Z18 HM0Z20 HM0Z22
OPTIONS
P05 Rear hood with internal roller
135 Configuration with a gearbox input of 1.000 rpm
KM1.A04.9Z Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.9Z Maintenance kit (basic kit + 6 belts XPB)
Ø 150 mm
TRITURADORA
B E L T Sx6
01 Body built in high strength steel.
02 Protection at front with chains.
03 Sliding skids.
04 Hydraulic hood with 2 hydraulic cylinders and an external roller
incorporated on hood.
05 Shifting three point linkage with an hydraulic cylinder (shifting model).
06 Rotor with floating hammers assembled to the rotor with bolts of
27 mm diameter (Boltop system).
07 Transmission with 6 belts.
08 Gearbox with free wheel with a drive shaft of 1”3/4 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Replaceable counterblades TMC Cancela model C01.
TMH
A04
04 10
04
02
01
03
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 2322
00 00
MOD. TH-130 TH-160 TH-180 TH-200 TH-220 TH-250 TH-280 TH-300 TH2-300
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20 2,50 2,80 3,00 3,00
Total width (m) 1,55 1,85 2,05 2,25 2,45 2,75 3,05 3,25 3,39
Required input power (CV) 50 60 75 80 90 100 120 150 150
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 463,1
Gearbox input speed (rpm) 540 (in option 1.000) 1.000
Nr. of hammers a01 20 26 28 32 34 40 44 48 48
Nr. of blades a03 60 78 84 96 102 120 132 144 144
Counterblades 1 replaceable row + 1 fix row
Coupling category Cat. 2
Nr. of belts - type 6-xpb 6+6-xpb
adjustable height control Rear roller
pTO Shaft bondioli type 108
fix model weight (kg) 574 618 662 706 750 860 982 1.072 1.090
Shifting model weight (kg) - 836 842 886 930 990 1.058 1.148 1.166
Hydraulic cylinder stroke (mm) - 500 600 600 600 600 600 600 600
Working reach
mechanical 1 (mm)
650-650 800-800 900-900 1.000-1.000 1.100-1.100 1.250-1.250 1.400-1.400 1.500-1.500 1.500-1.500
hydraulic (mm)
- 992,5-1.007,5 1.192,5-1.207,5 1.192,5-1.407,5 1.192,5-1.607,5 1.292,5-1.807,5 1.392,5-2.007,5 1.392,5-2.207,5 1.800-1.800
REF. FIX MODEL HM1Y13 HM1Y16 HM1Y18 HM1Y20 HM1Y22 HM1Y25 HM1Y28 HM1Y30 HM1X30
REF. SHIFTING MODEL HM2Y16 HM2Y18 HM2Y20 HM2Y22 HM2Y25 HM2Y28 HM2Y30 HM8Z30
OPTIONS
034 Reversible three point linkage for fix models and gearbox with through axle
030 Gearbox with double free wheel (reversible connection to tractor)
035 Rotor assembled with blades
091 Removable light panels
135 Configuration with a gearbox input of 1.000 rpm
KM1.A01.1Y Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.1Y Maintenance kit (basic kit + 6 belts XPB) KM1.A01.1X Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.1X Maintenance kit (basic kit + 12 belts XPB) KM1.A03.1Y Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.1Y Maintenance kit (basic kit + 6 belts XPB) KM1.A03.1X Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.1X Maintenance kit (basic kit + 12 belts XPB)
TRITURADORA
01 Body with fix three point linkage and completely built in high strength steel.
02 Protection at front with metallic plates.
03 Internal rear roller with adjustment on height for ground adjustment
(double roller for widths of 280 and 300).
04 Reversible shifting three point linkage with an hydraulic cylinder
(shifting model).
05 Sidestep system on frame sides.
06 Rotor with floating hammers assembled to the rotor with bolts of
20 mm diameter.
07 Transmission with 6 belts (12 belts on TH2).
08 Gearbox with free wheel with a drive shaft of 1”3/4 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system)
unless on model TH2 (only 1.000 rpm).
10 Replaceable counterblades TMC Cancela model C01.
TH
A01
A03
0803 06
04
03
01
04
03
B E L T Sx6
B E L T Sx6
B E L T Sx6 + /
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 2524
MOD. THP-540 THP-580
TECHNICAL FEATURES
Working width (m) 5,40 5,80
Total width (m) 5,62 6,02
Required input power (CV) 150 180
Max. allowed power (CV) 360
Rotor/s cutting diameter (mm) 463,1
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a01 88
Nr. of blades a03 264
Counterblades 2 + 2 fix rows
Coupling category Cat. 2 / Cat. 3
Nr. of belts - type 6 + 6-xpb
adjustable height control Roller / Wheels (in option)
pTO Shaft bondioli type 108
Weight (kg) 2.120 2.235
Working reach mechanical 1 (mm) 2.700-2.700 2.900-2.900
REF. MOD. HM4X54 HM4X58
OPTIONS
035 Rotor assembled with blades
135 Configuration with a gearbox input of 1.000 rpm
235 Stabilizing side wheels (without rollers)
236 Stabilizing side wheels (including rollers)
KM1.A01.4X Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.4X Maintenance kit (basic kit + 12 belts XPB) KM1.A03.4X Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.4X Maintenance kit (basic kit + 12 belts XPB)
01 Body built in high strength steel.
02 Double three point linkage with an hydrauling folding system and shock-
absorber system for the unfolding operation.
03 Consists in 2 separated folding bodies.
04 Internal rear rollers with adjustment on height for ground adjustment.
05 Protection at front with metallic plates.
06 Rotor with floating hammers assembled to the rotor with bolts of a
diameter of 20 mm.
07 Transmission with 6 belts on each body.
08 Gearboxes with free wheel with a drive shaft of 1”3/8 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Wheels on three point linkage for height adjustment.
11 Stabilizing side wheels (in option).
THP
A01
A03
360º
03
02
06
05
01
04
option 236
B E L T Sx6
B E L T Sx6 +
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 2726
MOD. TJL-220 TJL-250 TJL-280 TJL-300 TJL-320 TJL2-300 TJL2-320
TECHNICAL FEATURES
Working width (m) 2,20 2,50 2,80 3,00 3,20 3.00 3,20
Total width (m) 2,46 2,76 3,06 3,26 3,46 3.25 3,45
Required input power (CV) 90 100 120 150 160 150 160
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 463,1
Gearbox input speed (rpm) 540 (in option 1.000) 1.000
Nr. of hammers a01 34 40 44 48 52 48 52
Nr. of blades a03 102 120 132 144 156 144 156
Counterblades 2 replaceable rows
Coupling category Cat. 2
Nr. of belts - type 6-xpb 4 + 4-xpb
Skids adjustable bolted (2 positions)
adjustable height control Roller / Skids (2 positions)
pTO Shaft bondioli type 108
fix model weight (kg) 980 1.080 1.150 1.220 1.290 1.295 1.385
Shifting model weight (kg) 1.060 1.160 1.230 1.300 1.370 1.365 1.460
Hydraulic cylinder stroke (mm) 600
Working reachmechanical 1 (mm) 1.100-1.100 1.250-1.250 1.400-1.400 1.500-1.500 1.600-1.600 1.500-1.500 1.600-1.600
hydraulic (mm) 1.194,5-1.605,5 1.264,5-1.835,5 1.364,5-2.035,5 1.364,5-2.235,5 1.692,5-2.107,5 1.364,5-2.235,5 1.867,5-1.867,5
REF. FIX MODEL HM8U22 HM8U25 HM8U28 HM8U30 HM8U32 HM9U30 HM9U32
REF. SHIFTING MODEL HM7U22 HM7U25 HM7U28 HM7U30 HM7U32 HM0U30 HM0U32
OPTIONS
035 Rotor assembled with blades
237 Assembled with wheels without roller
091 Removable light panels
135 Configuration with a gearbox input of 1.000 rpm
KM1.A01.8U Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.8U Maintenance kit (basic kit + 6 belts XPB) KM1.A01.9U Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.9U Maintenance kit (basic kit + 8 belts XPB) KM1.A03.8U Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.8U Maintenance kit (basic kit + 6 belts XPB) KM1.A03.9U Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.9U Maintenance kit (basic kit + 8 belts XPB)
040302
B E L T Sx6
TJL
01 Body built in high strength steel with fixed three point linkage (2 positions).
02 Rear hood with double mechanical adjustment.
03 Internal rear roller with height adjustment for ground adjustment.
04 Shifting three point linkage with an hydraulic cylinder (shifting model).
05 Protection at front with metallic plates.
06 Rotor with floating hammers assembled to the rotor with bolts of a
diameter of 20 mm.
07 Transmission with 6 belts (4 + 4 belts on TJL2).
08 Gearbox with free wheel with a drive shaft of 1”3/4 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Replaceable counterblades TMC Cancela model C01.
A01
A03
B E L T Sx4
B E L T Sx4 + /
06
01
03
05
02
04
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 2928
MOD. TJ-200 TJ-250 TJ-280 TJ-300 TJ-320 TJ2-300 TJ2-320
TECHNICAL FEATURES
Working width (m) 2,00 2,50 2,80 3,00 3,20 3,00 3,20
Total width (m) 2,27 2,77 3,07 3,27 3,47 3,26 3,46
Required input power (CV) 80 120 135 150 160 150 160
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 645
Gearbox input speed (rpm) 540 1.000
Nr. of hammers a10 26 32 36 38 40 38 40
Nr. of blades a07 52 + 26 64 + 32 72 + 36 76 + 38 80 + 40 76 + 38 80 + 40
Counterblades 2 replaceable rows
Coupling category Cat. 2
Nr. of belts - type 6-xpb 4 + 4-xpb
Skids adjustable bolted (2 positions)
adjustable height control Roller (3 positions) / Skids (2 positions)
pTO Shaft bondioli type 108
Weight (kg) 984 1.134 1.304 1.474 1.644 1.524 1.704
Working reach mechanical 1 (mm) 1.000-1.000 1.250-1.250 1.400-1.400 1.500-1.500 1.600-1.600 1.500-1.500 1.600-1.600
REF. MOD. HM3Y20 HM3Y25 HM3Y28 HM3Y30 HM3Y32 HM5V30 HM5V32
OPTIONS
153 Rotor assembled with blades A07
037 Assembled with rear wheels without roller
239 Assembled with rear wheels and roller
091 Removable light panels
240 Fins on rear hood for spreading
KM1.A10.3Y Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A10.3Y Maintenance kit (basic kit + 6 belts XPB) KM1.A10.5V Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A10.5V Maintenance kit (basic kit + 8 belts XPB) KM1.A07.3Y Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A07.3Y Maintenance kit (basic kit + 6 belts XPB) KM1.A07.5V Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A07.5V Maintenance kit (basic kit + 8 belts XPB)
0502
01 Body built in high strength steel with fixed three point linkage.
02 Rear hood with double mechanical adjustment.
03 Double external rear roller with height adjustment for ground adjustment.
04 Protection at front with chains.
05 Rotor with floating hammers assembled to the rotor with bolts of a
diameter of 24 mm.
06 Transmission with 6 belts (4 + 4 belts on TJ2).
07 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
08 Gearbox with free wheel with a drive shaft of 1”3/4 Z6.
09 Replaceable counterblades TMC Cancela model C02.
TJ
A10
A07
B E L T Sx6
B E L T Sx4
B E L T Sx4 + /
04
03
0201
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 3130
MOD. TJS-300 TJS-320
TECHNICAL FEATURES
Working width (m) 3,00 3,20
Total width (m) 3,37 3,57
Required input power (CV) 150 170
Max. allowed power (CV) 250
Rotor/s cutting diameter (mm) 732
Gearbox input speed (rpm) 1.000
Nr. of hammers a10 38 40
Nr. of blades a07 76 + 38 80 + 40
Counterblades 2 replaceable rows
Coupling category Cat. 2
Nr. of belts - type 4 + 4-xpb
Skidsadjustable bolted
(2 positions)
adjustable height control Roller (3 positions) /
Skids (2 positions)
pTO Shaft bondioli
Weight (kg) 2.216 2.393
Working reach mechanical 1 (mm) 1.500-1.500 1.600-1.600
REF. MOD. HM4Y30 HM4Y32
OPTIONS
077 Assembled with rear wheels without roller
094 Assembled with rear wheels and roller
091 Removable light panels
260 Protection at front with metallic plates
093 Front protection combining metallic plates and chains
153 Rotor assembled with blades A07 and counterblades C02
240 Fins on rear hood for the spreading of the shredded material
092 Hydraulic rear hood
KM1.A10.4Y Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A10.4Y Maintenance kit (basic kit + 8 belts XPB) KM1.A07.4Y Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A07.4Y Maintenance kit (basic kit + 8 belts XPB)
01 option 094 option 240
B E L T Sx4
B E L T Sx4
01 Body built in high strength steel with fixed three point linkage.
02 Rear hood with double mechanical adjustment (hydraulic in option).
03 Double external rear roller with height adjustment for ground adjustment.
04 Protection at front with metallic plates or chains (in option).
05 Rotor with floating hammers assembled to the rotor with bolts of a
diameter of 24 mm.
06 Transmission with 4 + 4 belts.
07 Gearbox with free wheel with an input of 1.000 rpm and a drive shaft
of 1”3/4 Z6.
08 Replaceable counterblades TMC Cancela model C02.
TJS
A10
A07 +
02
04
01
03
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 3332
MOD. TV-085 TV-110 TV-130 TV-150 TV-180 TV-200
TECHNICAL FEATURES
Working width (m) 0,85 1,10 1,30 1,50 1,80 2,00
Total width (m) 1,13 1,40 1,60 1,80 2,10 2,20
Required input power (CV) 35 40 50 70 80 90
Max. allowed power (CV) 100
Rotor/s cutting diameter (mm) 412,3
Gearbox input speed (rpm) 540
Nr. of hammers a01 14 16 18 22 26 30
Counterblades 1 replaceable row + 1 fix row
Coupling category Cat. 1 / Cat. 2
Nr. of belts - type 4-xpb
adjustable height control directional wheels
pTO Shaft bondioli type G5
Weight (kg) 566 694 771 852 978 1.054
Working reach mechanical 1 (mm) 442,5 567,5 667,5 767,5 917,5 1.017,5
REF. MOD. HM5Y08 HM5Y11 HM5Y13 HM5Y15 HM5Y18 HM5Y20
OPTIONS
039 Mechanical pick-up feeder
038 Adjustable on height rear roller without wheels
040 Assembled with rear 360º swinging wheels
115 Sideskirts
KM1.A01.5Y Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.5Y Maintenance kit (basic kit + 4 belts XPB)
Ø 30 mm
02 option 040
B E L T Sx4
01 Body with fixed three point linkage.
02 Down pick-up feeder with hydraulic drive.
03 Rear pneumatic directional wheels.
04 Rake with tines for feeding.
05 Mulching system with a sieve.
06 Rotor with floating hammers assembled to the rotor with bolts of a diameter
of 20 mm.
07 Transmission with 4 belts.
08 Gearbox with free wheel with an input of 540 rpm and a drive shaft of 1”3/8 Z6.
TV
01 03
02
04
A01
07
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 3534
MOD. TO -130 TO -150 TO -180 TO -200 TO -220
TECHNICAL FEATURES
Working width (m) 1,30 1,50 1,80 2,00 2,20
Total width (m) 1,54 1,74 2,04 2,24 2,44
Required input power (CV) 60 70 80 90 105
Max. allowed power (CV) 120
Rotor/s cutting diameter (mm) 412,3
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 12 14 16 18 20
Counterblades 2 fix rows
Coupling category Cat. 2
Nr. of belts - type 6-xpb
adjustable height control Wheels / Roller
pTO Shaft bondioli type 108
Weight (kg) 1.100 1.235 1.360 1.445 1.540
Working reach mechanical 1 (mm) 650-650 750-750 900-900 1.000-1.000 1.100-1.100
REF. MOD. HM7V13 HM7V15 HM7V18 HM7V20 HM7V22
OPTIONS
135 Configuration with a gearbox input of 1.000 rpm
030 Gearbox with a double free wheel (to work on reverse position)
139 Assembled with roller
253 Assembled with rear 360º swinging wheels
KM1.A04.7V Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.7V Maintenance kit (basic kit + 6 belts XPB)
Ø 150 mm
0603 04
B E L T Sx6
01 Body built in high strength steel.
02 Reverse fix three point linkage to work on reverse position.
03 Double pick-up feeder with an hydraulic drive.
04 Support rear wheels fix or 360º directional (in option) with height adjustment.
05 Rear roller (in option).
06 Mulching system with a sieve.
07 Rotor with floating hammers assembled to the rotor with bolts of a diameter
of 27 mm. (Boltop system).
08 Transmission with 6 belts.
09 Gearbox with free wheel with a drive shaft of 1”3/4 Z6.
10 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
TO
A04
01
02
04
02
06
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 3736
MOD. TVS-085 TVS-110 TVS-130 TVS-150 TVS-180 TVS-200
TECHNICAL FEATURES
Working width (m) 0,85 1,10 1,30 1,50 1,80 2,00
Total width (m) 1,07 1,32 1,52 1,72 2,02 2,22
Required input power (CV) 50 60 70 80 90 100
Max. allowed power (CV) 100
Rotor/s cutting diameter (mm) 406,3
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a06 10 + 10 14 + 14 16 + 16 20 + 20 22 + 22 26 + 26
Counterblades 2 replaceable rows + 1 fix row
Coupling category Cat. 2
Nr. of belts - type 4-xpb
adjustable height control Wheels
pTO Shaft bondioli type G5
Weight (kg) 695 770 850 900 1.040 1.120
Working reach mechanical 1 (mm) 442,5-442,5 567,5-567,5 667,5-667,5 767,5-767,5 917,5-917,5 1.017,5-1.017,5
REF. MOD. HM6Y08 HM6Y11 HM6Y13 HM6Y15 HM6Y18 HM6Y20
OPTIONS
129 Sideskirts
028 Gearbox with a double free wheel (to work on reverse position)
136 Double kit of tines for the rake
135 Configuration with a gearbox input of 1.000 rpm
KM1.A06.6Y Basic maintenance kit (2 sets of hammers + 2 bolts + grease) KM2.A06.6Y Maintenance kit (basic kit + 4 belts XPB)
Ø 100 mm
03/05 04
B E L T Sx4
01 Body built in high strength steel.
02 Reverse fix three point linkage to work on reverse position.
03 Double pick-up feeder with an hydraulic drive and speed adjustment.
04 Support rear wheels 360º directional.
05 Rake with tines for feeding.
06 Mulching system with an open mulching cavity.
07 Rotor with fix hammers with a patented mulching system.
08 Transmission with 4 belts.
09 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
10 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
11 Replaceable counterblades made in a wearing resistant steel.
TVS360º
01 04
03
05
02
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 3938
MOD. TVC-130 TVC-150 TVC-180 TVC-200
TECHNICAL FEATURES
Working width (m) 1,30 1,50 1,80 2,00
Total width (m) 1,73 1,93 2,23 2,43
Required input power (CV) 70 80 90 100
Max. allowed power (CV) 110
Rotor/s cutting diameter (mm) 457,1
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a06 16 + 16 20 + 20 22 + 22 26 + 26
Counterblades 2 replaceable rows + 1 fix row
Coupling category Cat. 2
Nr. of belts - type 5-xpb
adjustable height control Roller / Wheels
pTO Shaft bondioli type G8
Weight (kg) 1.014 1.050 1.190 1.270
Working reachmechanical 1 (mm) 753,5-581,5 853,5-681,5 1.003,5-831.5 1.103,5-931.5
mechanical 2 (mm) 581,5-753,5 681,5-853,5 831,5-1.003,5 931,5-1.103,5
REF. MOD. HM9S13 HM9S15 HM9S18 HM9S20
OPTIONS
249 Sideskirts TVC
028 Gearbox with a double free wheel (to work on reverse position)
136 Tines for rake
137 Double kit of tines for the rake
044 Assembled with rear 360º swinging wheels
KM1.A06.9S Basic maintenance kit (2 sets of hammers + 2 bolts + grease) KM2.A06.9S Maintenance kit (basic kit + 5 belts XPB)
Ø 150 mm
B E L T Sx5
01 Body built in high strength steel.
02 Reverse fix three point linkage to work on reverse position.
03 Double pick-up feeder with an hydraulic drive and speed adjustment.
04 Support rear wheels fix or 360º directional (in option) with height adjustment.
05 Mulching system with an open mulching cavity.
06 Rotor with fix hammers with a patented mulching system.
07 Transmission with 5 belts.
08 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
09 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
10 Replaceable counterblades made in a wearing resistant steel.
11 Hydraulic motor of the pick-up with a side extension shaft with bearings to connect the
feeding system.
TVC360º
02
01
01
04
03
03 0804
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 4140
00
MOD. TOS-150 TOS-180 TOS-210
TECHNICAL FEATURES
Working width (m) 1,50 1,80 2,10
Total width (m) 1,95 2,25 2,55
Required input power (CV) 110 130 150
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 542,5
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a06 20 + 20 22 + 22 26 + 26
Counterblades 2 replaceable rows + 1 fix row
Coupling category Cat. 2
Nr. of belts - type 6-xpb
adjustable height control Wheels
pTO Shaft bondioli type 108
Weight (kg) 1.330 1.420 1.696
Working reach mechanical 1 (mm) 750-750 900-900 1.050-1.050
REF. MOD. HM8Y15 HM8Y18 HM8Y21
OPTIONS
044 Assembled with rear 360º swinging wheels
135 Configuration with a gearbox input of 1.000 rpm
136 Tines for rake
137 Double kit of tines for the rake
KM1.A06.8Y Basic maintenance kit (2 sets of hammers + 2 bolts + grease) KM2.A06.8Y Maintenance kit (basic kit + 6 belts)
Ø 200 mm
0503 04
B E L T Sx6
01 Body built in high strength steel.
02 Reverse fix three point linkage to work on reverse position.
03 Double pick-up feeder, both up and down with an hydraulic drive and
speed adjustment.
04 Support rear wheels fix or 360º directional (in option) with
height adjustment.
05 Gearbox with double free wheel with a drive shaft of 1”3/4 Z6.
06 Mulching system with an open mulching cavity.
07 Rotor with fix hammers with a patented mulching system.
08 Transmission with 6 belts.
09 Hydraulic motor of the pick-up with a side extension shaft with bearings
to connect the feeding system.
10 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys (DS system).
TOS02
05
01
07 10
04
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 4342
MOD. TPT-160 TPT-180 TPT-200 TPT-250
TECHNICAL FEATURES
Working width (m) 1,60 1,80 2,00 2,50
Total width (m) 1,92 2,12 2,32 2,82
Capacidad de carga (m3) 2,56 2,88 3,20 4,00
Required input power (CV) 80 100 110 130
Max. allowed power (CV) 200 200 200 200
Rotor/s cutting diameter (mm) 412,3
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a01 16 18 20 26
Counterblades 1 replaceable row
Coupling category Cat. 2
Nr. of belts - type 6-xpb
Skids protección
adjustable height control Rear roller
pTO Shaft bondioli type 108
Weight (kg) 1.352 1.430 1.506 1.660
Working reach mechanical 1 (mm) 800-800 900-900 1.000-1.000 1.250-1.250
REF. MOD. HM0Y16 HM0Y18 HM0Y20 HM0Y25
OPTIONS
135 Configuration with a gearbox input of 1.000 rpm
KM1.A04.0Y Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.0Y Maintenance kit (basic kit + 6 belts XPB)
Ø 120 mm
07 08
B E L T Sx6
01 Body built in high strength steel.
02 Protection at front with metallic plates.
03 Hooper with hydraulic opening.
04 Unload of material to the ground.
05 Mulching system with self loading.
06 Rotor with floating hammers assembled to the rotor with bolts of 27 mm
diameter (Boltop system).
07 Transmission with 6 belts.
08 Gearbox with free wheel with a drive shaft of 1”3/4 Z6.
09 Input of 540 rpm. In option 1.000 rpm.
TPT
A04
01
07
03
02
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 4544
MOD. TDS-130 TDS-160 TDS-180 TDS-200 TDS-220
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20
Total width (m) 1,53 1,83 2,03 2,23 2,43
Required input power (CV) 65 70 75 85 95
Max. allowed power (CV) 100
Rotor/s cutting diameter (mm) 383,7
Gearbox input speed (rpm) 540
Nr. of hammers a01 20 26 28 32 34
Nr. of blades a03 60 78 84 96 102
Counterblades 1 replaceable row
Coupling category Cat. 2
Nr. of belts - type 4-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type G7
Weight (kg) 774 816 858 900 942
Working reach hydraulic (mm) 766,5-2.083,5 766,5-2.383,5 766,5-2.583,5 926,5-2.783,5 892,5-2.983,5
REF. MOD. HM2X13 HM2X16 HM2X18 HM2X20 HM2X22
OPTIONS
142 Pneumatic shock-absorber in lift hydraulic cylinder
043 PTO shaft with double CV joint
024 Rubber protection at both front and rear
035 Rotor assembled with blades
KM1.A01.2X Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) KM2.A01.2X Maintenance kit (basic kit + 4 belts XPB) KM1.A03.2X Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) KM2.A03.2X Maintenance kit (basic kit + 4 belts XPB)
90º
45º
Ø 60 mm
07
B E L T Sx4
01 Body built in high strength steel with a replaceable inner shell.
02 Three point linkage with parallelogram device for displacement.
03 Internal rear roller with height adjustment for ground adjustment
and sliding skids.
04 Protection at front with metallic plates.
05 Rotor with floating hammers assembled to the rotor with bolts of
20 mm diameter model A01.
06 Transmission with 4 belts.
07 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
08 Input of 540 rpm.
09 Replaceable counterblades TMC Cancela model C01.
TDS
A03
A01
01
06
02
03
04
09 option 142
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232
MULCHER
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 4746
MOD. TDR-130 TDR-160 TDR-180 TDR-200 TDR-220
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20
Total width (m) 1,55 1,85 2,05 2,25 2,45
Required input power (CV) 70 80 100 110 130
Max. allowed power (CV) 200 200 200 200 200
Rotor/s cutting diameter (mm) 436
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 12 16 18 20 22
Counterblades 2 replaceable rows + 1 fix row
Coupling category Cat. 2
Nr. of belts - type 6-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type 108
Weight (kg) 874 949 988 1.020 1.066
Working reach hydraulic (mm) 883,5-2.263,5 746,5-2.383,5 746,5-2.583,5 746,5-2.783,5 892,5-2.983,5
REF. MOD. HM3X13 HM3X16 HM3X18 HM3X20 HM3X22
OPTIONS
048 PTO shaft with double CV joint
P02 Reinforced inner shell built with wear resistant steel
241 Configuration with a gearbox input of 1.000 rpm and special balancing on cardan transmission
KM1.A04.3X Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.3X Maintenance kit (basic kit + 6 belt XPB)
90º
45º
Ø 100 mm
0903
B E L T Sx6
01 Body built in high strength steel.
02 Three point linkage with parallelogram device
for displacement and with a mechanical safety device.
03 Protection at front with chains.
04 Float device on three linkage point to control ground adjustment
as well as impacts during transport.
05 Pneumatic shock-absorber for deployment.
06 Internal rear roller with height adjustment for ground adjustment and
protection skids.
07 Rotor with floating hammers assembled to the rotor with bolts of 27 mm
diameter (Boltop system).
08 Transmission with 6 belts.
09 Gearbox with free wheel with a drive shaft of 1”3/8 Z6.
10 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys.
11 Replaceable counterblades TMC Cancela model C01.
TDR
A04
0105
02
04
03
06
06
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL www.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m 4948
MOD. TDE-200 TDE-220 TDE-250
TECHNICAL FEATURES
Working width (m) 2,00 2,20 2,50
Total width (m) 2,73 2,93 3,23
Required input power (CV) 110 130 140
Max. allowed power (CV) 200
Rotor/s cutting diameter (mm) 486,8
Gearbox input speed (rpm) 540 (in option 1.000)
Nr. of hammers a04 20 22 26
Counterblades 2 replaceable rows + 1 fix row
Coupling category Cat. 2
Nr. of belts - type 6-xpb
Skids fix bolted (1 position)
adjustable height control Rear roller
pTO Shaft bondioli type 108
Weight (kg) 1.140 1.194 1.255
Hydraulic cylinder stroke (mm) 253 / 205
Working reach hydraulic (mm) 409.5-3.160,5 409.5-3.360,5 409.5-3.660,5
REF. MOD. HM7Z20 HM7Z22 HM7Z25
OPTIONS
048 PTO shaft with double CV joint
241 Configuration with a gearbox input of 1.000 rpm and special balancing on cardan transmission
KM1.A04.7Z Basic maintenance kit (2 hammers + 1 bolt + 1 nut + grease) KM2.A04.7Z Maintenance kit (basic kit + 6 belts XPB)
90º
45º
Ø 120 mm
TRITURADORA
B E L T Sx6
TDE
01 Body built in high strength steel.
02 Three point linkage with parallelogram device for displacement and
with a mechanical safety device.
03 Protection at front with chains.
04 Float device on three linkage point to control ground adjustment as
well as impacts during transport.
05 Pneumatic shock-absorber for deployment.
06 Internal rear roller with height adjustment for ground adjustment
and protection skids.
07 Rotor with floating hammers assembled to the rotor with bolts of
27 mm diameter (Boltop system).
08 External gearbox with free wheel with a drive shaft of 1”3/8 Z6.
09 Transmission with 6 belts.
10 Input of 540 rpm. In option 1.000 rpm by inversion of pulleys.
A04
01
05
04
02
06
03
MOd. 90 100
110
120
130
140
150
160
170
180
190
200
250
300
310
320
340
360
380
400
450
pg.
D1 • • • • 15-30 52
D2 • • • • 35-60 54
D3 • • • • • • • 40-85 56
D3B • • • 70-85 58
D3S • • • • • • 40-85 60
D5S • • • • • 85-300 62
DL • 45-75 64
DF2 • • 70-100 66
DF3 • • • • • 100-125 68
DP2 • • 125-160 70
DP3 • • • 100-140 72
DX • • 60-85 74
DX2 • • 70-100 76
DX3 • • • • • 85-125 78
DXP3 • 100-125 80
90 100
110
120
130
140
150
160
170
180
190
200
250
300
310
320
340
360
380
400
450
cmWORKING WIdTH
CV
ROTARY BRUSH CUTTERS
ROTARY BRUSH CUTTER
5352
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00
TMC CANCELA AGRICULTURAL
MOD. D1-090 D1-100 D1-110 D1-120
TECHNICAL FEATURES
Working width (m) 0,90 1,00 1,10 1,20
Total width (m) 0,97 1,07 1,17 1,27
Required input power (CV) 15 20 25 25
Max. allowed power (CV) 30 30 30 30
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.036,8
linear speed(m/s)
540 rpm 44,52 54,29 59,72 65,14
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 1
Skids adjustables on height (3 positions)
adjustable height control Skids
pTO Shaft Cardan with fuse
free wheel In option
fix model weight (kg) 154 178 208 236
Shifting model weight (kg) - - - 253
Hydraulic cylinder stroke (mm) - - - 340
Working reachmechanical (mm) 450-450 420-580 470-630 520-680
hydraulic (mm) - - - 770-770
REF. FIX MODEL VM1A09 VM1A10 VM1A11 VM1A12
REF. SHIFTING MODEL VM2A12
OPTIONS
001 PTO shaft with free wheel incorporated on clutch
002 PTO shaft with clutch
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
03
01 Body with external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 Three point linkage made in bent steel strip with chain straps.
05 Hitch with 2 positions.
06 Chains or blades holding to rotor with bolts.
07 Gearbox with an input of 540 rpm and a drive shaft of 1”3/8 Z6.
D1
RV08
Optio
n
RV01
Stan
dard
RV01
Optio
n
04
02
05
0103
07
ROTARY BRUSH CUTTER
5554
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 00
TMC CANCELA AGRICULTURAL
MOD. D2-120 D2-130 D2-140 D2-150
TECHNICAL FEATURES
Working width (m) 1,20 1,30 1,40 1,50
Total width (m) 1,27 1,37 1,47 1,57
Required input power (CV) 35 40 50 55
Max. allowed power (CV) 60
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.036,8
linear speed(m/s)
540 rpm 60,80 66,23 71,66 77,09
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 1 / Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Skids
pTO Shaft Cardan with clutch
free wheel In option
fix model weight (kg) 246 274 310 330
Shifting model weight (kg) 271 301 331 355
Hydraulic cylinder stroke (mm) 340 400 400 400
Working reachmechanical (mm) 600-600 570-730 620-780 670-830
hydraulic (mm) 770-770 850-850 900-900 950-950
REF. FIX MODEL VM3A12 VM3A13 VM3A14 VM3A15
REF. SHIFTING MODEL VM4A12 VM4A13 VM4A14 VM4A15
OPTIONS
007 PTO shaft with free wheel incorporated on clutch
008 Control rear wheel
257 Rear roller
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
01 Body with external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 Three point linkage made in bent steel strip with chain straps and
hydraulic cylinder (in shifting models).
05 Lower hitch linkage with an offset of 80 mm against the three point
linkage on fix model.
06 Chains or blades holding to rotor with bolts.
07 Gearbox with an input of 540 rpm and a drive shaft of 1”3/8 Z6.
08 Model with hydraulic shifting.
D2
RV08
Optio
n
RV01
Stan
dard
RV01
Optio
n
03 08
02
07
01
05
04
03
ROTARY BRUSH CUTTER
5756
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURAL
MOD. D3-130 D3-140 D3-150 D3-160 D3-170 D3-180 D3-200
TECHNICAL FEATURES
Working width (m) 1,30 1,40 1,50 1,60 1,70 1,80 2,00
Total width (m) 1,40 1,50 1,60 1,70 1,80 1,90 2,10
Required input power (CV) 40 45 50 60 70 75 80
Max. allowed power (CV) 85
Gearbox input speed (rpm) 540
Rotor speed (rpm) 540 rpm 988,2
linear speed(m/s)
540 rpm 63,13 68,30 73,47 78,65 83,82 89,00 99,34
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 1 / Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Skids
pTO Shaft Cardan with clutch
free wheel In option
fix model weight (kg) 344 372 416 456 496 550 665
Shifting model weight (kg) 451 492 534 564 606 649 708
Hydraulic cylinder stroke (mm) 400 400 400 500 500 500 500
Working reachmechanical (mm) 570-730 620-780 670-830 720-880 770-930 820-980 920-1.080
hydraulic (mm) 850-850 900-900 950-950 1.050-1.050 1.100-1.100 1.150-1.150 1.250-1.250
REF. FIX MODEL VM5A13 VM5A14 VM5A15 VM5A16 VM5A17 VM5A18 VM5A20
REF. SHIFTING MODEL VM6A13 VM6A14 VM6A15 VM6A16 VM6A17 VM6A18 VM6A20
OPTIONS
221 PTO shaft with free wheel incorporated on clutch
008 Control rear wheel
257 Rear roller
227 Rotor RV01 assembled with blades
229 Rotor RV11 assembled with blades
230 Rotor RV11 assembled with chains
00 00
01 Body with external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 Three point linkage made in bent steel strip with chain straps and
hydraulic cylinder (in shifting models).
05 Lower hitch linkage with 2 positions and with an offset of 80 mm against
the three point linkage on fix model.
06 Chains or blades holding to rotor with bolts (rotor RV11).
07 Chains or blades holding to rotor with screws (rotor RV11).
08 Gearbox with an input of 540 rpm and a drive shaft of 1”3/8 Z6.
09 Model with hydraulic shifting.
D3
RV01
Stan
dard
RV01
Optio
n
RV11
Optio
n
03 09
01
03
08
02
04
05
5958
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 00
TMC CANCELA AGRICULTURAL
MOD. D3B-160 D3B-180 D3B-200
TECHNICAL FEATURES
Working width (m) 1,60 1,80 2,00
Total width (m) 1,72 1,92 2,12
Required input power (CV) 70 75 80
Max. allowed power (CV) 85
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 988,2
linear speed(m/s)
540 rpm 78,65 89 99,34
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Skids
pTO Shaft Cardan with clutch
free wheel In option
Weight (kg) 768 870 974
Working reach mechanical (mm) 720-880 820-980 920-1.080
REF. MOD. VM6D16 VM6D18 VM6D20
OPTIONS
222 Reinforced gearbox from 90 up to 220 CV
221 PTO shaft with free wheel incorporated on clutch
258 Rotor RV02 assembled with blades
229 Rotor RV11 assembled with blades
230 Rotor RV11 assembled with chains
ROTARY BRUSH CUTTER
01 Body with double height with internal reinforcements.
02 Protection at front and rear by chains.
03 Oscillating protection rear cover.
04 Rounded skids adjustable on height (3 positions) with Widest system.
05 Three point linkage made in bent steel strip and with an offset of 80 mm.
against the three point linkage.
06 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z20 (in option
reinforced gearbox with a drive shaft of 1”3/4 Z6).
07 Chains or blades holding to rotor with bolts (rotor RV02).
08 Chains or blades holding to rotor with screws (rotor RV11).
D3B
01
03 06
02
04
RV02
Optio
n
RV11
Optio
n
RV02
Stan
dard
03 04
RV11
Stan
dard
ROTARY BRUSH CUTTER
6160
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 0000
TMC CANCELA AGRICULTURAL
MOD. D3S-130 D3S-140 D3S-150 D3S-160 D3S-170 D3S-180
TECHNICAL FEATURES
Working width (m) 1,30 1,40 1,50 1,60 1,70 1,80
Total width (m) 1,41 1,51 1,61 1,71 1,81 1,91
Required input power (CV) 45 50 60 70 75 80
Max. allowed power (CV) 85
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 988,2
linear speed(m/s)
540 rpm 63,13 68,30 73,47 78,65 83,82 89
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Skids
pTO Shaft Cardan with clutch
free wheel In option
fix model weight (kg) 426 498 534 578 644 712
Shifting model weight (kg) 614 626 648 671 739 807
Hydraulic cylinder stroke (mm) 400 400 400 500 500 500
Working reachmechanical (mm) 570-730 620-780 670-830 720-880 770-930 820-980
hydraulic (mm) 850-850 900-900 950-950 1.050-1.050 1.100-1.100 1.150-1.150
REF. FIX MODEL VM7A13 VM7A14 VM7A15 VM7A16 VM7A17 VM7A18
REF. SHIFTING MODEL VM8A13 VM8A14 VM8A15 VM8A16 VM8A17 VM8A18
OPTIONS
221 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
01 Body with internal reinforcements.
02 Protection at front and rear by chains.
03 Rounded skids adjustable on height.
04 Three point linkage made in bent steel strip with strip straps and
with an offset of 80 mm on fix model.
05 Three point linkage with an hydraulic shifting guided with nylon
replaceable bushes (in shifting model).
06 Rear bended pins to guide the brush into the machine.
07 Chains or blades holding to rotor with bolts (rotor RV01).
08 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z6.
D3S
RV01
Stan
dard
RV01
Optio
n
03 0806
01
05
02
06
03
08
04
ROTARY BRUSH CUTTER
6362
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 0000
TMC CANCELA AGRICULTURAL
MOD. D5S-150 D5S-160 D5S-170 D5S-180 D5S-200
TECHNICAL FEATURES
Working width (m) 1,50 1,60 1,70 1,80 2,00
Total width (m) 1,61 1,71 1,81 1,91 2,11
Required input power (CV) 85 90 110 120 140
Max. allowed power (CV) 200 200 200 300 300
Gearbox input speed (rpm) 1.000 / (in option 540)
Rotor speed(rpm)
540 rpm 1.009,8 793,8
1.000 rpm 1.000
linear speed(m/s)
540 rpm 75,08 80,37 85,65 71,49 79,80
1.000 rpm 74,35 79,59 84,82 90,06 100,53
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 2
Skids adjustables on height (3 positions) with Widest system
adjustable height control Skids
pTO Shaft Cardan with clutch
free wheel In option
fix model weight (kg) 762 854 978 1.102 1.318
Shifting model weight (kg) 854 946 1.071 1.194 1.410
Hydraulic cylinder stroke (mm) 400 500 500 500 500
Working reachmechanical (mm) 670-830 720-880 770-930 820-980 920-1.080
hydraulic (mm) 920-920 1.000-1.000 1.050-1.050 1.100-1.100 1.250-1.250
REF. FIX MODEL VM9A15 VM9A16 VM9A17 VM9A18 VM9A20
REF. SHIFTING MODEL VM0A15 VM0A16 VM0A17 VM0A18 VM0A20
OPTIONS
131 Gearbox with an input of 1.000 rpm
225 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
*Interchangeable component
01 Body with internal reinforcements.
02 Protection at front and rear by chains.
03 Rounded skids adjustable on height and with soles made in wearing
resistant steel and Widest system.
04 Rear bended pins to guide the brush into the machine.
05 Three point linkage made in bent steel strip with tubular straps.
06 Three point linkage with an hydraulic shifting guided with nylon
replaceable bushes (in shifting model).
07 Chains or blades holding to rotor with bolts.
08 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z6 (standard).
D5S
RV01
Stan
dard
RV01
Optio
n
03 0804
03
05
04
02
01
08
ROTARY BRUSH CUTTER
6564
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 0000
TMC CANCELA AGRICULTURAL
MOD. DL-150
TECHNICAL FEATURES
Working width (m) 1,50
Total width (m) 1,65
Required input power (CV) 45
Max. allowed power (CV) 75
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.036,8
linear speed(m/s)
540 rpm 77,09
Nr. of rotors 1
Nr. of chains 4
Nr. of blades 2
Coupling category Cat. 2
Skidsadjustables on height (3 positions)
adjustable height control Skids
pTO ShaftCardan with
clutch
free wheel In option
Weight (kg) 640
Working reach mechanical (mm) 455-2.055
REF. MOD. VM2B15
OPTIONS
007 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
01 Body with external reinforcements.
02 Central structure made from tubular steel with a mulcher aside.
03 Mechanical swinging/folding device for adapting to the ground.
04 Three point linkage made in bent steel strip with a central strap.
05 Protection at front and rear by chains.
06 Skids adjustable on height.
07 Top cover to avoid damage in orchards.
08 Chains or blades holding to rotor with bolts.
09 Gearbox with an input of 540 rpm and a drive shaft of 1”3/8 Z6.
DL
07 09
RV08
Optio
n
RV01
Stan
dard
RV01
Optio
n
0504 06 07
07
05
06
04
0103
ROTARY BRUSH CUTTER
6766
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 0000
TMC CANCELA AGRICULTURAL
MOD. DF2-200 DF2-250
TECHNICAL FEATURES
Working width (m) 2,00 2,50
Total width (m) 2,07 2,57
Required input power (CV) 70
Max. allowed power (CV) 100
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.036,8
linear speed(m/s)
540 rpm 56,46 69,49
Nr. of rotors 2
Nr. of chains 4
Nr. of blades 4
Coupling category Cat. 2
Skidsadjustables on height
(3 positions)
adjustable height control Rear wheels / Skids
pTO Shaft Cardan with clutch
free wheel In option
Weight (kg) 865 1.065
Working reach mechanical (mm) 1.000-1.000 1.250-1.250
REF. MOD. VM3B20 VM3B25
OPTIONS
085 Central rear roller
091 Removable light panels
226 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
01 Body with internal and external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 360º directional wheels with independant shock-absorbers.
05 Three point linkage made in bent steel strip.
06 Chains or blades holding to rotor with bolts.
07 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z6.
DF2
RV08
Optio
n
RV01
Stan
dard
RV01
Optio
n
360º
02 0703
02
01
03
05
07 04
ROTARY BRUSH CUTTER
6968
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 0000
TMC CANCELA AGRICULTURAL
MOD. DF3-300 DF3-320 DF3-340 DF3-360 DF3-400
TECHNICAL FEATURES
Working width (m) 3,00 3,20 3,40 3,60 4,00
Total width (m) 3,08 3,28 3,48 3,68 4,08
Required input power (CV) 85 90 95 100 110
Max. allowed power (CV) 125
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.004,4
linear speed(m/s)
540 rpm 56,80 61,00 62,58 64,16 72,05
Nr. of rotors 3
Nr. of chains 6
Nr. of blades 6
Coupling category Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Rear wheels + Skids
pTO Shaft Cardan with clutch
free wheel On cardan (in option)
Weight (kg) 1.080 1.110 1.255 1.172 1.237
Working reach mechanical (mm) 1.500-1.500 1.600-1.600 1.700-1.700 1.800-1.800 2.000-2.000
REF. MOD. VM4B30 VM4B32 VM4B34 VM4B36 VM4B40
OPTIONS
085 Central rear roller
086 Dual three point linkage
089 Lateral three point linkage for transport
091 Removable light panels
226 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
01 Body with internal and external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 360º directional wheels with independant shock-absorbers.
05 Three point linkage made in bent steel strip.
06 Chains or blades holding to rotor with bolts.
07 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z20.
DF3
RV08
Optio
n
RV01
Stan
dard
RV01
Optio
n
360º
02 0703
01
05
02
04
03
07
04
ROTARY BRUSH CUTTER
7170
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 00
TMC CANCELA AGRICULTURAL
MOD. DP2-310D DP2-380D
TECHNICAL FEATURES
Working width (m) 3,10 3,80
Total width (m) 3,20 3,90
Required input power (CV) 125 130
Max. allowed power (CV) 160
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.004,4
linear speed(m/s)
540 rpm 78,89 95,71
Nr. of rotors 2
Nr. of chains 4
Nr. of blades 4
Coupling category Cat. 2
Skidsadjustables on height
(3 positions)
adjustable height control Rear wheels / Skids
pTO Shaft Cardan with clutch
free wheel In option
Weight (kg) 1.930 2.320
Hydraulic cylinder stroke (mm) 400 400
Working reach mechanical (mm) 1.040-2.460 1.200-3.000
Transport width 1.090-1.340 1.240-1.630
REF. MOD. VM6B31 VM6B38
OPTIONS
085 Central rear roller
226 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
65º
5º
01 Made with 2 foldable independent bodies with internal and
external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 360º directional wheels with independant shock-absorbers.
05 Chains or blades holding to rotor with bolts.
06 Shifting three point linkage made in bent steel strip.
07 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z20.
DP2
RV01
Stan
dard
RV01
Optio
n
360º
02 03
RV08
Optio
n
01
06
02
04
03
ROTARY BRUSH CUTTER
7372
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 00
TMC CANCELA AGRICULTURAL
MOD. DP3-360 DP3-400 DP3-450
TECHNICAL FEATURES
Working width (m) 3,60 4,00 4,50
Total width (m) 3,74 4,14 4,64
Required input power (CV) 100 120 130
Max. allowed power (CV) 140
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.004,4
linear speed(m/s)
540 rpm 64,16 67,84 78,89
Nr. of rotors 3
Nr. of chains 6
Nr. of blades 6
Coupling category Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Rear wheels / Skids
pTO Shaft Cardan with clutch
free wheel In option
Weight (kg) 1.498 2.430 2.430
Working reach mechanical (mm) 1.800-1.800 2.000-2.000 2.250-2.250
Transport width 1.050-1.050 1.185-1.185 1.540-1.540
REF. MOD. VM7B36 VM7B40 VM7B45
OPTIONS
085 Central rear roller
226 PTO shaft with free wheel incorporated on clutch
227 Rotor RV01 assembled with blades
228 Rotor RV08 assembled with blades
01 Made with 3 foldable independent bodies with internal and external reinforcements.
02 Protection at front and rear by chains.
03 Skids adjustable on height.
04 360º directional wheels with independant shock-absorbers.
05 Chains or blades holding to rotor with bolts.
06 Shifting three point linkage made in bent steel strip.
07 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z20.
DP3
RV08
Optio
n
RV01
Stan
dard
RV01
Optio
n
360º
02 03
01
04
0205 03
ROTARY BRUSH CUTTER
7574
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 00
TMC CANCELA AGRICULTURAL
MOD. DX-160 DX-200
TECHNICAL FEATURES
Working width (m) 1,60 2,00
Total width (m) 1,70 2,10
Required input power (CV) 60 80
Max. allowed power (CV) 85
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 988,2
linear speed(m/s)
540 rpm 78,65 99,34
Nr. of rotors 1
Nr. of bladessimples 3
doubles 3 + 3
Coupling category Cat. 1 / Cat. 2
Skidsadjustables on height
(3 positions)
adjustable height control Rear wheels / Skids
pTO Shaft bondioli
free wheel In option
fix model weight (kg) 456 762
Shifting model weight (kg) 564 861
Hydraulic cylinder stroke (mm) 500 500
Working reachmechanical (mm) 720-880 920-1.080
hydraulic (mm) 1.050-1.050 1.250-1.250
REF. FIX MODEL VM1D16 VM1D20
REF. SHIFTING MODEL VM5D16 VM5D20
OPTIONS
221 PTO shaft with free wheel incorporated on clutch
231 Rotor RV04 assembled with blades (2 cutting levels)
01 Body externally reinforced.
02 Protection at front and rear by chains.
03 Skids adjustable on height and with soles made in wearing resistant steel.
04 360º directional wheels with shock-absorbers.
05 1 rotor Flow Up with 1 cutting level.
06 System for guiding the material.
07 Three point linkage made in tubular steel with chain straps.
08 Chains or blades holding to rotor with screws and bushes.
09 Gearbox with an input of 540 rpm and a drive shaft of 1”3/8 Z6.
10 Cardan with clutch.
11 Three point linkage with an hydraulic shifting guided with nylon replaceable
bushes (in shifting model).
DX
RV03
Stan
dard
RV04
Optio
n
360º
02 03
01
03
04
07
02
09
ROTARY BRUSH CUTTER
7776
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00 0000
TMC CANCELA AGRICULTURAL
MOD. DX2-200 DX-250
TECHNICAL FEATURES
Working width (m) 2,00 2,50
Total width (m) 2,07 2,57
Required input power (CV) 70 80
Max. allowed power (CV) 100
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.036,8
linear speed(m/s)
540 rpm 56,46 69,49
Nr. of rotors 2
Nr. of bladessimples 4
doubles 4 + 4
Coupling category Cat. 2
Skidsadjustables on height
(3 positions)
adjustable height control Rear wheels / Skids
pTO Shaft Cardan with clutch
free wheel In option
Weight (kg) 968 1.043
Working reach mechanical (mm) 1.000-1.000 1.250-1.250
REF. MOD. VM2D20 VM2D25
OPTIONS
085 Central rear roller
091 Removable light panels
226 PTO shaft with free wheel incorporated on clutch
232 Rotor RV06 assembled with blades (2 cutting levels)
01 Body externally reinforced.
02 Protection at front and rear by chains.
03 Skids adjustable on height and with soles made in wearing resistant steel.
04 360º directional wheels with shock-absorbers.
05 Chains or blades holding to rotor with screws and bushes.
06 2 rotors Flow Up with 1 cutting level.
07 System for guiding the mulched material.
08 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z6.
DX2
RV05
Stan
dard
RV06
Optio
n
360º
080302
02
03
01
04
08
ROTARY BRUSH CUTTER
7978
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURAL
MOD. DX3-300 DX3-320 DX3-340 DX3-360 DX3-400
TECHNICAL FEATURES
Working width (m) 3,00 3,20 3,40 3,60 4,00
Total width (m) 3,08 3,28 3,48 3,68 4,08
Required input power (CV) 85 90 90 100 100
Max. allowed power (CV) 125
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.004,4
linear speed(m/s)
540 rpm 56,80 61 62,58 64,16 72,05
Nr. of rotors 3
Nr. of bladessimples 6
doubles 6 + 6
Coupling category Cat. 2
Skids adjustables on height (3 positions)
adjustable height control Rear wheels / Skids
pTO Shaft Cardan with clutch
free wheel In option
Weight (kg) 1.170 1.200 1.255 1.262 1.327
Working reach mechanical (mm) 1.500-1.500 1.600-1.600 1.700-1.700 1.800-1.800 2.000-2.000
REF. MOD. VM3D30 VM3D32 VM3D34 VM3D36 VM3D40
OPTIONS
085 Central rear roller
086 Dual three point linkage
089 Lateral three point linkage for transport
091 Removable light panels
226 PTO shaft with free wheel incorporated on clutch
232 Rotor RV06 assembled with blades (2 cutting levels)
080000
01 Body reinforced on the upside.
02 Protection at front and rear by chains.
03 Skids adjustable on height and with soles made in wearing resistant steel.
04 360º directional wheels with shock-absorbers.
05 Chains or blades holding to rotor with screws and bushes.
06 3 rotors Flow Up with 1 cutting level.
07 System for guiding the material.
08 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z20.
DX3
RV05
Stan
dard
RV06
Optio
n
360º
0302
01
03
02
04
08
8180
TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
w w w. t m c c a n c e l a . c o m
00
TMC CANCELA AGRICULTURAL
MOD. DXP3-360
TECHNICAL FEATURES
Working width (m) 3,60
Total width (m) 3,74
Required input power (CV) 100
Max. allowed power (CV) 125
Gearbox input speed (rpm) 540
Rotor speed(rpm)
540 rpm 1.004,4
linear speed(m/s)
540 rpm 64,16
Nr. of rotors 3
Nr. of bladessimples 6
doubles 12
Coupling category Cat. 2
Skidsadjustables on height (3 positions)
adjustable height controlRear
wheels / Skids
pTO ShaftCardan with
clutch
free wheel
Weight (kg) 1.588
Working reach mechanical (mm) 1.800-1.800
Transport width 1.050-1.050
REF. MOD. VM4D36
OPTIONS
091 Removable light panels
226 PTO shaft with free wheel incorporated on clutch
085 Central rear roller
232 Rotor RV06 assembled with blades (2 cutting levels)
DESBROZADORA
01 Made with 3 hydraulic foldable independent bodies.
02 Floating three point linkage for a perfect adjustment to the ground.
03 Protection at front and rear by chains.
04 Skids adjustable on height and with soles made in wearing resistant steel.
05 Rear 360º directional wheels with shock-absorbers.
06 Three point linkage made from bent steel strip.
07 3 rotors Flow Up with 1 cutting level.
08 Gearbox with an input of 540 rpm and a drive shaft of 1”3/4 Z20.
09 System for guiding the material.
10 Chains or blades holding to rotor with screws and bushes.
DXP3
RV05
Stan
dard
RV06
Optio
n
360º
0403
04
06
06
01
05
03
08
LOG SPLITTERS
www.tmccancela.com |+34 981 695 232
8584
LOG SPLITTER
w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
MOD. OR-TM-14 OR-TM-22
TECHNICAL FEATURES
Travel (m) 0,65 0,65
Thrust force (Tn) 14 22
Required input power (CV) 25 35
Weight (kg) 288 368
REF. MOD. CM1E14 CM1E22
OPTIONS
061 Oil cooler (12 V)
150 Structure for loading logs (hydraulic)
OR-TM01
02
01 Welded frame with strong structure for withstanding high loads.
02 Wood guiding system.
03 Confortable and ergonomic manual commands.
04 Height adjustment of the working table.
05 Large diameter wood splitting.
06 Mechanical drive of the pump.
07 Transmission by cardan.
08 High pushing capacity: 14 and 22 Tn.
09 Cross blades welded to the structure.
03
option 1500903
www.tmccancela.com |+34 981 695 232
8786
LOG SPLITTER
w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
OR-HV01
02
03
01 Welded frame with strong structure for withstanding high loads.
02 Wood guiding system.
03 Confortable and ergonomic manual commands.
04 Height adjustment of the working table.
05 Large diameter wood splitting.
06 Driven by the hydraulic system of the tractor.
07 High pushing capacity: 14 and 22 Tn.
08 Flexible hydraulic hoses with quick connections jack to the tractor.
09 Cross blades welded to the structure.
0903
MOD. OR-HV-14 OR-HV-22
TECHNICAL FEATURES
Travel (m) 0,65 0,65
Thrust force (Tn) 14 22
Required input power (CV) 20 30
Weight (kg) 224 300
REF. MOD. CH2E14 CH2E22
OPTIONS
061 Oil cooler (12 V)
www.tmccancela.com |+34 981 695 232
8988
LOG SPLITTER
w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
MOD. OR-HV-14M OR-HV-14T OR-HV-22
TECHNICAL FEATURES
Travel (m) 0,65 0,65 0,65
Required input power (Tn) 14 14 22
Max. allowed power (CV) 20 20 30
Weight (kg) 224 224 300
REF. MOD. CE3E14 CE4E14 CE4E22
OPTIONS
061 Oil cooler (12 V)
OR-EL01
02
03
01 Welded frame with strong structure for withstanding high loads.
02 Wood guiding system.
03 Confortable and ergonomic manual commands.
04 Large diameter wood splitting.
05 Electric drive, single or three phase.
06 High pushing capacity: 14 and 22 Tn.
07 Cross blades welded to the structure on the three phase model
and vertical on single phase one.
05 0705
COMPLEMENTS
www.tmccancela.com |+34 981 695 232
9392 w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
MOD. PFD-M PFD-H
TECHNICAL FEATURES
Required input power (CV) 40
Max. allowed power (CV) 90
lateral displacement (mm) 800-800
Weight (kg) 230 302
REF. MOD. CM6E CM7E
BORERS
062 BR-1 Borer for stakes 15x90 cm
063 BR-1 Borer for stakes 30x90 cm
064 BR-1 Borer for stakes 45x90 cm
065 BR-1 Borer for stakes 60x90 cm
066 BR-2 Borer for planting 40x90 cm
067 BR-2 Borer for planting 50x90 cm
OPTIONS
068 Gearbox with manual inverter
069 Set of blades BR-1 15x90
070 Set of blades BR-1 30x90
071 Set of blades BR-1 45x90
072 Set of blades BR-1 60x90
073 Set of blades BR-2 40x90
074 Set of blades BR-2 50x90
075 Auger tip replacement for BR-1
AUGERPFD
01 Welded frame with strong structure.
02 Leveling shock-absorber with 2 springs for a better adjustment to the field while drilling.
03 Manual (PFD-M) or Hydraulic (PFD-H) side displacement.
04 Drive with tractor PTO. Reinforced gearbox for tractors with up 90 CV and an input of 540 rpm with a shaft of 1”3/8 Z6.
05 Flange for coupling different types of borers.
BR2
BR1
0102
02 03 04
ANNEXES
www.tmccancela.com |+34 981 695 232
9796 w w w. t m c c a n c e l a . c o m
TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
MODEL
A01 A02 A03 A04 A07A06 A10
TP • •TPS • •TG •TGS •TMS •TMD •TGH • • •TMH •TH • •TH2 • •THP • •TJL • •TJL2 • •TJ • •TJ2 • •TJS • •TV •TO •TVS •TVC •TOS •TPT •TDS • •TDR •TDE •PVP €
UNIT 8,07 € 16,01 € 9,14 € 23,49 € 62,05 € 19,98 € 15,40 €
HAMMERS & BLADES
A01
0,6 kg
A02
1,7 kg
A04
2,3 kg
A10
1,9 kgA03
0,8 kg
A07
2,7 kg
THREE POINT LINKAGE
Cat 1 2 3 4
Tractorhorse power …50 Hp …100 Hp …225 Hp …475 Hp
a 683 825 965 1.166,5
b 44,5 52 52 65
C 39 49 52 68
d1 22 28 36,6 50,8
d2 19 25,4 31,7 45
H 460 610 685 685
d2
B
H
d1
A C
TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURALwww.tmccancela.com |+34 981 695 232
1 3/4” – Z20
CLOCKWISE
D8x32x38
COUNTERCLOCKWISE
w w w. t m c c a n c e l a . c o m
PTO (POWER TAKE OFF)
d1mm
d2mm
d3mm
d4mm
Rmm
dIN 9611* 35,6635,40
31,9031,75
34,8734,47
31,10 7,156,65
ISO 500 34,9634,93
31,9031,75
34,8734,85
31,1030,85
7,056,55
aSae S203 34,9634,92
31,8731,75
34,8734,85
30,68 7,116,61
d1mm
d2mm
T1mm
d3mm
d4mm
T2mm
Rmm
dIN 9611* 35,6735,40
31,9031,75
34,8734,47
31,10 7,156,65
ISO 500 34,9634,93
31,9031,75
34,8734,85
29,0028,90
8,648,51
7,056,55
aSae S203 34,9534,90
29,9729,72
8,768,69
34,8734,70
27,89 8,648,51
7,116,61
T2D
3
D4
T1
D1
D2
38±0,8
Ø29
,5Ø
29,3
R
60˚
6
D3
D4
D1
D2
25.5 ±0,8
Ø29
,5Ø
29,3
5R
60˚
1 3/8” – Z6
1 3/8” – Z21
1 3/4” – Z6
www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
MA
QU
INA
RIA
AG
RÍC
OLA
CA
NC
ELA
, S. L
. In
scri
ta e
n e
l Reg
istr
o M
erca
nti
l de
A C
oru
ña,
To
mo
177
4 d
el a
rch
ivo
, Sec
ció
n G
ral.,
Fo
lio 5
7, H
oja
nº.
C-1
5911
, In
scri
pci
ón
1ª
- C
. I. F
.: B
-155
4974
4
Pedra Salgueira, s/n | Anxeriz
15684 | Tordoia | A Coruña (SPAIN)
Tlf: +34 981 695 074
Fax: +34 981 695 232
www.tmccancela.com
ORDER FORM
DATE / / N.º
DISTRIBUTOR SIGNATURE AND STAMP (in accordance with the order) PAYMENT METHOD
COMPANY
ADDRESS
DELIVERY ADDRESS
NAME OF PURCHASER
PHONE NUMBER CELL PHONE
MACHINE REFERENCE
MACHINE DESCRIPTION
OPTIONAL 1 OPTIONAL 3
OPTIONAL 5 OPTIONAL 7
OPTIONAL 2
OPTIONAL 6
OPTIONAL 4
OPTIONAL 8
KIT KIT
OPTIONAL 1 OPTIONAL 3
OPTIONAL 5 OPTIONAL 7
OPTIONAL 2
OPTIONAL 6
OPTIONAL 4
OPTIONAL 8
KIT KIT
QUANTITY
REMARKS
DELIVERY DATE
DELIVERY DATE
MACHINE REFERENCE
MACHINE DESCRIPTION
QUANTITY
REMARKS
NOTES / COMMENTS
HOW TO PLACE AN ORDER
100
TMC CANCELA AGRICULTURAL
0TARIFA TMC CANCELA 2015www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURAL PRICE LISTwww.tmccancela.com |+34 981 695 232
23
MOD. TH-130 TH-160 TH-180 TH-200 TH-220 TH-250 TH-280 TH-300 TH2-300
TECHNICAL FEATURES
Working width (m) 1,30 1,60 1,80 2,00 2,20 2,50 2,80 3,00 3,00
Total width (m) 1,55 1,85 2,05 2,25 2,45 2,75 3,05 3,25 3,39
Required input power (cv) 50 60 75 80 90 100 120 150 150
Max. allowed power (cv) 200
Rotor/s cutting diameter (mm) 463,1
Gearbox input speed (rpm) 540 (in option 1.000) 1.000
Nr. of hammers A01 20 26 28 32 34 40 44 48 48
Nr. of blades A03 60 78 84 96 102 120 132 144 144
counterblades 1 replaceable row + 1 fix row
coupling category cat. 2
Nr. of belts - type 6-XPB 6+6-XPB
control of adjustable height Rear roller
PTO Shaft Bondioli type 108
Fix model weight (kg) 574 618 662 706 750 860 982 1.072 1.090
Shifting model weight (kg) - 836 842 886 930 990 1.058 1.148 1.166
Mouvement of the hydraulic cylinder (mm) - 500 600 600 600 600 600 600 600
Working reach
mechanical 1 (mm)
650-650 800-800 900-900 1.000-1.000 1.100-1.100 1.250-1.250 1.400-1.400 1.500-1.500 1.500-1.500
hydraulic (mm)
- 992,5-1.007,5 1.192,5-1.207,5 1.192,5-1.407,5 1.192,5-1.607,5 1.292,5-1.807,5 1.392,5-2.007,5 1.392,5-2.207,5 1.800-1.800
REF. FIX MODEL HM1Y13 HM1Y16 HM1Y18 HM1Y20 HM1Y22 HM1Y25 HM1Y28 HM1Y30 HM1X30
5.750 € 6.150 € 6.300 € 6.650 € 6.950 € 7.500 € 8.000 € 8.300 € 9.600 €REF. SHIFTING MODEL HM2Y16 HM2Y18 HM2Y20 HM2Y22 HM2Y25 HM2Y28 HM2Y30 HM8Z30
7.050 € 7.150 € 7.500 € 7.850 € 8.350 € 8.850 € 9.150 € 10.450 €OPTIONS
034Reversible three point linkage for fix models and gearbox with through axle
522 €
030Gearbox with double free wheel (reversible connection to tractor)
420 €
035 Rotor assembled with blades 0 €
091 Removable light panels 544 €
135 Configuration with a gearbox input of 1.000 rpm 0 €
KM1.A01.1Y Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) 53 €KM2.A01.1Y Maintenance kit (basic kit + 6 belts XPB) 168 €KM1.A01.1X Basic maintenance kit (4 hammers + 2 bolts + 2 nuts + grease) 53 €KM2.A01.1X Maintenance kit (basic kit + 12 belts XPB) 284 €KM1.A03.1Y Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) 53 €KM2.A03.1Y Maintenance kit (basic kit + 6 belts XPB) 168 €KM1.A03.1X Basic maintenance kit (4 sets of blades + 2 bolts + 2 nuts + grease) 53 €KM2.A03.1X Maintenance kit (basic kit + 12 belts XPB) 284 €
MA
QU
INA
RIA
AG
RÍC
OLA
CA
NC
ELA
, S. L
. In
scri
ta e
n e
l Reg
istr
o M
erca
nti
l de
A C
oru
ña,
To
mo
177
4 d
el a
rch
ivo
, Sec
ció
n G
ral.,
Fo
lio 5
7, H
oja
nº.
C-1
5911
, In
scri
pci
ón
1ª
- C
. I. F
.: B
-155
4974
4
Pedra Salgueira, s/n | Anxeriz15684 | Tordoia | A Coruña (SPAIN)Tlf: +34 981 695 074Fax: +34 981 695 [email protected] www.tmccancela.com
ORDER FORMDATE / /
N.º
DISTRIBUTOR SIGNATURE AND STAMP (in accordance with the order)
PAYMENT METHOD
COMPANY
ADDRESS
DELIVERY ADDRESS
NAME OF PURCHASER
PHONE NUMBER
CELL PHONE
MACHINE REFERENCE
MACHINE DESCRIPTION
OPTIONAL 1
OPTIONAL 3OPTIONAL 5
OPTIONAL 7
OPTIONAL 2
OPTIONAL 6
OPTIONAL 4
OPTIONAL 8KIT
KIT
OPTIONAL 1
OPTIONAL 3OPTIONAL 5
OPTIONAL 7
OPTIONAL 2
OPTIONAL 6
OPTIONAL 4
OPTIONAL 8KIT
KIT
QUANTITY
REMARKS
DELIVERY DATE
DELIVERY DATE
MACHINE REFERENCE
MACHINE DESCRIPTION
QUANTITY
REMARKS
NOTES / COMMENTS
TH-160
AGRÍCOLA PORRIÑOPONTEVEDRAO PORRIÑOJESÚS CAAMAÑO988 023 112
608 112 457
H M 1 Y 1 6 0 3 5
AGRICOLA PORRIÑO
C.I.F. B-15559634
O PorriñoPontevedra
2
K M 1 A 0 1 1 Y
8 1 2015
SPARE PARTS SERVICE
w w w. t m c c a n c e l a . c o m
Use always original partsQuality Assurance
102
www.tmccancela.com |+34 981 695 232 TMC CANCELA AGRICULTURALTMC CANCELA AGRICULTURAL
TERMS AND CONDITIONS
The information and photographic material contained in this document is indicative.It is not allowed to do any copies. TMC Cancela reserves the right of doing any changes, even substantial or
important ones, without notice.The usage of this price list is only reserved for the TMC Cancela authorized dealers and distributors.
TECHNICAL DATA
| The technical data in this document is only indicative. TMC CANCELA reserves the right to make any changes to the products
without notice.
EC DECLARATION OF CONFORMITY
| The TMC CANCELA equipment and machines are in accordance with the current Machinery Directive 2006/42/EC (with
application from 29/12/2009, replacing the old Directive 98/37/EC).
| Each machine is accompanied by the EC Declaration of Conformity, the Certificate of Manufacture and the User’s Manual, being
responsibility of the reseller agent the delivery to the end user.
NOTES / COMMENTS
A G R Í C O L A
15T. +34 981 695 074F. +34 981 695 232
Anxeriz - 15684 Tordoia - A Coruña (SPAIN)[email protected]
www.tmccancela.com