User’sManual ADMAG TI Series
AXG Magnetic FlowmeterHART Communication Type
IM 01E22A02-02EN
IM 01E22A02-02EN2nd Edition
AXG Magnetic Flowmeter
1
IM 01E22A02-02EN
ADMAG TI SeriesAXG Magnetic FlowmeterHART Communication Type
IM 01E22A02-02EN 2nd Edition
2nd Edition: Oct. 2017 (KP)All Rights Reserved, Copyright © 2017, Yokogawa Electric Corporation
Contents1. Introduction ...................................................................................................5
1.1 For Safe Use of Product ...................................................................................... 71.2 Warranty ................................................................................................................ 8
2. Basic Operating Procedures .......................................................................92.1 Operation by Display unit ................................................................................... 92.2 DisplayandBasicConfiguration ....................................................................... 9
2.2.1 Display .................................................................................................. 9
2.2.2 BasicConfigurationforDisplay ........................................................... 10
2.3 Display Mode and Setting Mode ....................................................................... 122.4 Parameter Setting from Display Panel ............................................................ 13
2.4.1 SettingexampleofSelecttype Data:Flowrateunit ............................................................................. 13
2.4.2 SettingexampleofNumerictype Data: Flow rate span ........................................................................... 13
2.4.3 SettingExampleofAlphanumerictype Data: Tag No. ...................................................................................... 14
2.5 microSD Card Insertion/Removal .................................................................... 14
3. OperationwithHARTConfigurationTool ............................................... 153.1 ConnectingtheHARTConfigurationTool ...................................................... 153.2 HARTConfigurationToolandDeviceRevision ............................................. 15
3.2.1 Device Description (DD) and Device Revision ................................... 15
3.2.2 Device Type Manager (DTM) and Device Revision ........................... 16
3.3 Basic Setup ......................................................................................................... 163.4 ParametersConfiguration ................................................................................ 163.5 Data Renewing and Upload / Download Function ......................................... 173.6 SpecificFunctionsofHARTConfigurationTool ............................................ 19
3.6.1 BurstMode .......................................................................................... 19
3.6.2 EventNotification ................................................................................ 21
3.6.3 MultidropMode ................................................................................... 22
4. Functions ................................................................................................... 234.1 Basic Settings .................................................................................................... 24
4.1.1 Overview ............................................................................................. 24
4.1.2 PVMappingofProcessValue ............................................................ 25
4.1.3 DisplayoftheProcessValue .............................................................. 25
2
IM 01E22A02-02EN
4.1.4 Engineering Unit Setting ..................................................................... 25
4.1.5 Span Setting........................................................................................ 26
4.1.6 Damping Time Constant Setting ......................................................... 27
4.1.7 Low-cutFunctionSetting .................................................................... 28
4.1.8 Sensor’s Nominal Size Setting ........................................................... 29
4.1.9 Density Setting .................................................................................... 29
4.1.10 TemperatureSetting ........................................................................... 30
4.1.11 ZeroAdjustment .................................................................................. 30
4.2 Totalization Function ......................................................................................... 314.2.1 TotalizedValueandUnitSetting ......................................................... 31
4.2.2 Totalized-ValueDisplayandTotalizerFunction .................................. 32
4.2.3 TotalizationSwitchFunction ............................................................... 32
4.2.4 TotalizerOperationatAlarmOccurrence ............................................ 33
4.2.5 TotalizationFunctionStart/StopSetting .............................................. 33
4.2.6 Totalization Direction Setting .............................................................. 34
4.2.7 TotalizedValueReset/PresetFunction ............................................... 34
4.3 Pulse Output, Frequency Output, and Status Output .................................... 354.3.1 OutputsofI/O2,I/O3,andI/O4Terminals .......................................... 35
4.3.2 PulseOutput/FrequencyOutputMapping ........................................ 35
4.3.3 PulseWidthSetting ............................................................................. 36
4.3.4 Active Direction Setting ....................................................................... 36
4.3.5 PulseRateSetting .............................................................................. 37
4.3.6 FrequencyOutputRangeSetting ....................................................... 38
4.3.7 StatusOutputFunctionSetting ........................................................... 38
4.4 Status Input......................................................................................................... 394.4.1 ActiveDirectionSettingforStatusInput ............................................. 39
4.4.2 StatusInputFunctionSetting .............................................................. 40
4.5 Current Input and Current Output .................................................................... 404.5.1 CurrentOutputHigh/LowLimitFunction ............................................ 40
4.5.2 AbsoluteRangeFunction ................................................................... 41
4.5.3 AlarmOutputFunction ........................................................................ 41
4.5.4 CurrentOutputPriority ........................................................................ 42
4.5.5 CurrentValueAdjustmentFunction .................................................... 42
4.5.6 CurrentInputFunctionSetting ............................................................ 43
4.5.7 CurrentInputRangeSetting ............................................................... 43
4.5.8 CurrentInputHigh/LowLimitFunction ............................................... 43
4.6 Multi Range Function ........................................................................................ 444.6.1 MultiRangeTypes .............................................................................. 44
4.6.2 MultiRangeSetting ............................................................................. 44
4.6.3 MultiRangeOperation ........................................................................ 44
4.6.4 Forward/ReverseRange .................................................................... 45
4.6.5 CombinationofMultiRangeandForward/ReverseRange ............... 46
3
IM 01E22A02-02EN
4.6.6 External Contact Range ...................................................................... 47
4.7 Auxiliary Calculation Function ......................................................................... 474.7.1 FluidFlowDirectionSetting ................................................................ 47
4.7.2 RateLimitFunctionSetting ................................................................. 47
4.7.3 PulsingFlowSupportFunctionSetting .............................................. 49
4.7.4 PowerFrequencySynchronizationSetting ........................................ 49
4.7.5 DensityCorrectionCalculation ........................................................... 50
4.7.6 CalorieCalculation .............................................................................. 51
4.8 Alarm ................................................................................................................... 524.8.1 ErrorsandCountermeasures ............................................................. 52
4.8.2 Alarm Display Setting .......................................................................... 58
4.8.3 AlarmHistoryFunction........................................................................ 58
4.8.4 AlarmMaskFunction .......................................................................... 59
4.9 Display ................................................................................................................. 634.9.1 LanguageSetting ................................................................................ 63
4.9.2 Display Item Setting ............................................................................ 63
4.9.3 Decimal-Point Position Setting ........................................................... 64
4.9.4 DisplayLineCountandScrollSettings ............................................... 64
4.9.5 Trend Graph Setting ........................................................................... 65
4.9.6 Other Setting ....................................................................................... 66
4.9.7 microSD Card Setting ......................................................................... 68
4.10 Device Information ............................................................................................. 684.10.1 OrderInformation ................................................................................ 68
4.10.2 Device Revision .................................................................................. 69
4.10.3 MemoFunction ................................................................................... 69
4.11 Self-diagnostic Function ................................................................................... 704.11.1 TypesofDiagnosisFunctions ............................................................. 70
4.11.2 AlarmHigh/LowLimitFunction ........................................................... 70
4.11.3 Electrode Adhesion Detection ............................................................ 71
4.11.4 Sensor Empty Check .......................................................................... 72
4.11.5 WiringConnectionDiagnosis ............................................................. 72
4.11.6 Verification(DeviceHealthDiagnosis)Function ................................ 73
4.11.7 ElectrodeInsulationDeteriorationDiagnosis ..................................... 75
4.11.8 Flow Noise Diagnosis ......................................................................... 76
4.11.9 LowConductivityDiagnosis ................................................................ 76
4.12 Test Mode ............................................................................................................ 774.12.1 Test Mode Setting ............................................................................... 77
4.12.2 TestTerminalandValueSetting .......................................................... 78
4.12.3 TestModeAutoReset ......................................................................... 78
4.13 Event Management Function ............................................................................ 794.13.1 BackupFunction ................................................................................. 79
4.13.2 Restore/DuplicateFunction .............................................................. 81
4
IM 01E22A02-02EN
4.13.3 BackupandRestoreParameters ....................................................... 83
4.13.4 DataLoggingFunction ........................................................................ 93
4.14 Software Write Protection Function ................................................................ 94
5. Parameters of Magnetic Flowmeter ........................................................ 965.1 Parameter Lists for Display and HART Communication ............................... 975.2 Menu Tree of Display ....................................................................................... 1385.3 Menu Tree of HART Communication ............................................................. 144
Revision Information
<1. Introduction> 5
IM 01E22A02-02EN
1. IntroductionThismanualprovidesthebasicguidelinesforbasicoperationofADMAGTI(TotalInsight)SeriesAXGmagneticflowmeterswithHARTprotocol.For the items which are not covered in this manual,readtheapplicableuser’smanualsandgeneralspecificationsaslistedinTable1.1.ThesedocumentscanbedownloadedfromthewebsiteofYOKOGAWA.Toensurecorrectuseoftheinstrument,readthesemanualsthoroughlyandfullyunderstandhowtooperatetheinstrumentbeforeoperatingit.Formethodofcheckingthemodelandspecifications,readgeneralspecificationsaslistedin Table 1.1.Websiteaddress:http://www.yokogawa.com/fld/doc/ThesemanualscanbedownloadedfromthewebsiteofYOKOGAWAorpurchasedfromtheYOKOGAWArepresentatives.
Table1.1 ManualandGeneralSpecificationsList
Model Document Title Document No.
AXG AXG4A AX01C
ADMAG TI Series AXG/AXWMagneticFlowmeter Read Me First
IM 01E21A21-01Z1
ADMAG TI SeriesAXG/AXWMagneticFlowmeter SafetyManual
IM 01E21A21-02EN
ADMAG TI Series AXGMagneticFlowmeter InstallationManual
IM 01E22A01-01EN
ADMAG TI Series AXGMagneticFlowmeter MaintenanceManual
IM 01E22A01-02EN
ADMAG TI Series AXGMagneticFlowmeter BRAINCommunicationType
IM 01E22A02-01EN
ADMAG TI Series AXGMagneticFlowmeter HARTCommunicationType
IM 01E22A02-02EN(thismanual)
ADMAG TI Series AXGMagneticFlowmeter GeneralSpecifications
GS 01E22A01-01EN
AXFA11G
AXFSeriesMagnetic FlowmeterRead Me First
IM 01E20A21-01Z1
AXFA11GRemoteConverter [HardwareEdition/SoftwareEdition]
IM 01E20C01-01E
AXFA11GRemoteConverter GeneralSpecifications GS 01E20C01-01E
NOTEWhendescribingthemodelnamelikeAXG inthismanual,“”meansanyofthefollowing.002, 005, 010, 015, 025, 032, 040, 050, 065, 080, 100, 125, 150, 200, 250, 300, 350, 400
Precautions Related to the Protection, Safety, and Alteration of the Instrument
Thefollowingsafetysymbolmarksareusedinthismanualandinstrument.
WARNING
AWARNINGsigndenotesahazard.Itcallsattentiontoprocedure,practice,conditionorthelike,which,ifnotcorrectlyperformedoradheredto,couldresultininjuryordeathofpersonnel.
CAUTIONA CAUTION sign denotes a hazard. It calls attentiontoprocedure,practice,conditionorthelike,which,ifnotcorrectlyperformedoradheredto,couldresultindamagetoordestructionofpartoralloftheproduct.
IMPORTANTAn IMPORTANT sign denotes that attention is requiredtoavoiddamagetotheinstrumentorsystemfailure.
NOTEANOTEsigndenotesinformationnecessaryforessentialunderstandingofoperationandfeatures.
<1. Introduction> 6
IM 01E22A02-02EN
ThefollowingsymbolsareusedintheInstrumentandthemanualtoindicatetheaccompanyingsafetyprecautions:
Protectivegroundingterminal
Functionalgroundingterminal(Thisterminalshouldnotbeusedasaprotectivegroundingterminal.)AlternatingcurrentDirectcurrentCautionThissymbolindicatesthattheoperatormustrefertoanexplanationintheuser’smanualinordertoavoidtheriskofinjuryordeathofpersonnelordamagetotheinstrument.
Fortheprotectionandsafeuseoftheinstrumentandthesysteminwhichthisinstrumentisincorporated,besuretofollowtheinstructionsandprecautionsonsafetythatisstatedinuser’smanualaslistedinTable1.1wheneveryouhandletheinstrument.Takespecialnotethatifyouhandletheinstrumentinamannerthatviolatedtheseinstructions,theprotectionfunctionalityoftheinstrumentmaybedamagedorimpaired.Insuchcases,YOKOGAWAdoesnotguaranteethequality,performance,function,andsafetyofinstrument.
Regarding This User’s Manual• Thismanualshouldbeprovidedtotheenduser.
• Thecontentsofthismanualaresubjecttochangewithoutpriornotice.
• Allrightsreserved.NopartofthismanualmaybereproducedinanyformwithoutYOKOGAWA’swrittenpermission.
• YOKOGAWAmakesnowarrantyofanykindwithregardtothismanual,including,butnotlimitedto,impliedwarrantyofmerchantabilityandfitnessforaparticularpurpose.
• Ifanyquestionarisesorerrorsarefound,orifanyinformationismissingfromthismanual,informthenearestYOKOGAWAsalesoffice.
• Thespecificationscoveredbythismanualarelimitedtothoseforthestandardtypeunderthespecifiedmodelnumberbreak-downanddonotcovercustom-madeinstruments.
• Notethatchangesinthespecifications,construction,orcomponentpartsoftheinstrumentmaynotimmediatelybereflectedinthismanualatthetimeofchange,providedthatpostponementofrevisionswillnotcausedifficultytotheuserfromafunctionalorperformancestandpoint.
• Thismanualisintendedforthefollowingpersonnel;
Engineersresponsibleforinstallationandwiringoftheinstrument.
Personnelresponsiblefornormaldailyoperationoftheinstrument.
• Toensurecorrectuse,readthismanualandtheapplicablemanualsaslistedinTable1.1thoroughlybeforestartingoperation.ReadthegeneralspecificationsaslistedinTable1.1foritsspecification.
Trademarks:• AllthebrandsornamesofYokogawaElectric’s productsusedinthismanualareeithertrademarksorregisteredtrademarksofYokogawa Electric Corporation.
• Allothercompanyandproductnamesmentionedinthismanualaretradenames,trademarksorregisteredtrademarksoftheirrespective companies.
• Inthismanual,trademarksorregisteredtrademarks are not marked with ™ or ®.
<1. Introduction> 7
IM 01E22A02-02EN
1.1 For Safe Use of ProductFortheprotectionandsafeuseoftheinstrumentandthesysteminwhichthisinstrumentisincorporated,besuretofollowtheinstructionsandprecautionsonsafetythatisstatedinuser’smanualaslistedinTable1.1wheneveryouhandletheinstrument.Takespecialnotethatifyouhandletheinstrumentinamannerthatviolatedtheseinstructions,theprotectionfunctionalityoftheinstrumentmaybedamagedorimpaired.Insuchcases,YOKOGAWAshallnotbeliableforanyindirectorconsequentiallossincurredbyeitherusingornotbeingabletousetheInstrument.
(1) General
WARNING
• Do not open the cover in wet weather or humidenvironment.Whenthecoverisopen,statedenclosureprotectionisnotapplicable.
• Whenopeningthecover,waitformorethan20minutesafterturningoffthepower.Onlyexpert engineer or skilled personnel are per-mitted to open the cover.
(2) Operation
WARNING
Besuretoenablethewriteprotectfunctiontopreventtheoverwritingofparametersafterfinishingparametersetting.In rare cases, the IR switches may respond unexpectedlytowaterdropsorextraneoussubstancesstickingonthesurfaceofdisplaypanel,duetotheoperatingprincipal.Thepossibilityofmalfunctionarisesafterrainorcleaning operation near the place where the flowmeterisinstalled.Turningonandofftheflashlightetc.towardstheIRswitchmayalsobeacauseofmalfunction.ReadtheinstallationmanualaslistedinTable1.1forthehardwarewriteprotectfunction,andSection4.14forthesoftwarewriteprotectfunction.
(3) Maintenance
WARNING
• Ifdirt,dustorothersubstancessurfacesontheglassofdisplaycover,wipethemcleanwithasoftdrycloth.
• Maintenanceofthisflowmetershouldbeimplemented in a maintenance service shop where the necessity tools and environment condition are provided.
Thenecessityofthisenvironmentalconditionisthatambienttemperatureis5to40°C(themaximumrelativehumidityis80%fortem-perature5to31°C,anddecreasinglinearlyto50%relativehumidityat40°C).
(4) microSD Card
IMPORTANT• DonotstoreorusethemicroSDcardinplaces
with static electricity, near electrically charged objects, or where electrical noise is present. Doingsocanresultinshockordamage.
• DonotdisassembleormodifythemicroSDcard.
• Do not physically shock, bend, or pinch the microSD card.
• Duringreading/writingofdata,donotturnoffthepower,applyvibrationorshock,orpulloutthecard.Datacancorruptorbepermanentlylost.
• Use only micro SD cards sold by YOKOGA-WA.Operationcannotbeguaranteedwhenothercardsareused.
• WheninsertingthemicroSDcardintotheinstrument,makesuretoorientthemicroSDcardcorrectly(faceupordown)andinsertitsecurely.Ifnotinsertedcorrectly,themicroSDcardwillnotberecognizedbytheinstrument.
• DonottouchthemicroSDcardwithwethands.
• DonotusethemicroSDcardifitisdustyordirty.
• ThemicroSDcardcomesformatted.IfyouwanttoformatthemicroSDcard,usetheinstrument’sFormatfunction.
• YOKOGAWAprovidesnowarrantyfordam-ageto,orlossofdatarecordedonthemi-croSDcard,regardlessofthecauseofsuchdamage or loss.
Werecommendmakingbackupcopiesofyourdata.
<1. Introduction> 8
IM 01E22A02-02EN
1.2 Warranty• The warranty shall cover the period noted on thequotationpresentedtothepurchaseratthetimeofpurchase.Problemsoccurredduringthewarrantyperiodshallbasicallyberepairedfreeofcharge.
• Incaseofproblems,thecustomershouldcontacttheYOKOGAWArepresentativefromwhichtheinstrumentwaspurchased,orthenearestYOKOGAWAoffice.
• Ifaproblemariseswiththisinstrument,pleaseinformusofthenatureoftheproblemandthecircumstancesunderwhichitdeveloped,includingthemodelspecificationandserialnumber.Anydiagrams,dataandotherinformationyoucanincludeinyourcommunicationwillalsobehelpful.
• ResponsiblepartyforrepaircostfortheproblemsshallbedeterminedbyYOKOGAWAbasedonourinvestigation.
• ThePurchasershallbeartheresponsibilityforrepaircosts,evenduringthewarrantyperiod,ifthemalfunctionisdueto:- Improperand/orinadequatemaintenancebythepurchaser.
- Failureordamageduetoimproperhandling,useorstoragewhichisoutofdesignconditions.
- UseoftheproductinquestioninalocationnotconformingtothestandardsspecifiedbyYOKOGAWA,orduetoimpropermaintenanceoftheinstallationlocation.
- FailureordamageduetomodificationorrepairbyanypartyexceptYOKOGAWAoranapprovedrepresentativeofYOKOGAWA.
- Malfunctionordamagefromimproperrelocationoftheproductinquestionafterdelivery.
- Reasonofforcemajeuresuchasfires,earthquakes,storms/floods,thunder/lightening,orothernaturaldisasters,ordisturbances,riots,warfare,orradioactivecontamination.
<2. Basic Operating Procedures> 9
IM 01E22A02-02EN
2. Basic Operating Procedures2.1 Operation by Display unitTheparametersettingsfromdisplayunitcanbecarriedoutusingthethreeIR(infra-red)switches-namely,the[SET][SHIFT]and[▼]switches.TheIRswitchesenabletheusertosetparametersfromtheoutsideoftheglassofthedisplaycover.ThissectionprovidesdescriptionsofbasicparameterconfigurationandoperationprocesuresofIRswitches.Thisinstrumentcanbealsooperatedusingthededicatedhandheldterminalor the FieldMate (Versatile Device Management Wizard).Foroperationindetails,readChapter4orthehardware/softwareedition(forAXFA11)aslistedin Table 1.1.
WARNING
Besuretoenablethewriteprotectfunctiontopreventtheoverwritingofparametersafterfinishingparametersetting.In rare cases, the IR switches may respond unexpectedlytowaterdropsorextraneoussubstancesstickingonthesurfaceofdisplaypanel,duetotheoperatingprincipal.Thepossibilityofmalfunctionarisesafterrainorcleaning operation near the place where the flowmeterisinstalled.Turningonandofftheflashlightetc.towardstheIRswitchmayalsobeacauseofmalfunction.ReadtheinstallationmanualaslistedinTable1.1forthehardwarewriteprotectfunction,andSection4.14forthesoftwarewriteprotectfunction.
IMPORTANTOperatethedisplayunitundertheconditionwheredirectsunlight,etc...donotshinetotheIR switches directly when the parameter setting operationiscarriedout.
NOTE• Always keep the cover closed and operate the settingswitchesfromtheoutsideoftheglasswindow.
• Ifdirt,dustorothersubstancessurfacesontheglassofdisplaycover,wipethemcleanwithasoftdrycloth.
• Theoperationwithdirtyglovesmaycauseaswitch response error.
NOTEThelanguageonthedisplayissetto“English”asdefaultatthefactoryshipment.SelecttheadequatelanguagereferringtoSubsection2.2.2andSubsection4.9.1.Themenupassofthedisplayonthismanualisselectedto“English”.
2.2 Display and Basic Configuration
ThedisplayunitofAXGIntegralFlowmeterandAXG4ARemotetransmitterhasvariousfunctionsbelow.
2.2.1 Display
22.000mA0.0%
0.00000m/s
00 : 00VEL
FLP
A01SET SFT INC
Status icon and time
Data display(Abbreviation: see Table 2.2.1)Switch On/Off status(On: inverted)IR switches
F0201.ai
microSD card(Optional code: /MC)
<2. Basic Operating Procedures> 10
IM 01E22A02-02EN
(1) Basic operation of IR switchesTheoperationfromdisplaypanelisdonebyusingthethreeIRswitches;[SET],[SHIFT]and[▼].Thecombinationofthetwoswitchesprovidesadifferentfunction,andthefunctionisindicatedonthedisplay.
IR switch (Note 1)
Indicate of switch (Note 2)
Function
[SET►] SET▪Applyparameter(Note3)▪Enterdata(Note3)▪Movetonextmenu
[SHIFT] SFT ▪Movecursorright (Numerictypeparameter)
[▼] INC
▪Movecursordown (Select type parameter)▪Incrementvalue (Numerictypeparameter)▪Changepositionofdecimalpoint(Numerictypeparameter)
[SHIFT]+[▼](=[▲]) DEC
▪Movecursorup (Select type parameter)▪Decrementvalue (Numerictypeparameter)
SHIFT+SET►(=[ESC◄]) ESC ▪Cancel
▪Backtopreviousmenu
Note1: [A]+[B](=[C]):Thefunctionischangedtoswitch[C]whenswitch[B]ispushedwhilepushingswitch[A].
Note 2: [SET], [SFT], [INC], [DEC] and [ESC] indicate the assignedfunctioninaccordancewithdisplaymodeatthat time.
Note3: “Apply”and“Enter”areexecutedbypushing[SET]twice.Iftheexecutiondoesnotworkproperly,releasethefingerfromthedisplayglasscompletelyafterthefirstpushof[SET],andthenmakethesecondpush.
(2) Status iconsIcon Contents Icon Contents
WriteprotectInvalid WriteprotectValid
DeviceBusy DeviceFault
ReadyformicroSDcard
Accessing microSD card
Disable to access microSD card Uploading parameters
Downloading parameters Trendgraphexecuting
Systemalarmoccurs HARTcommunication
Processalarmoccurs Settingalarmoccurs
Warningoccurs Informationoccurs
Display Damping Valid Operation level:Operator
Operation level:Maintenance
Operation level:Specialist
(3) Data indication partTheprocessvaluesareavailabletoselect8itemsmaximumonthedisplay.Itispossibletoindicate4itemsmaximumonthedisplayatthesametime,and the rest 4 items are able to show by scrolling.
Table 2.2.1 Abbreviation table of process values to be indicated on the display.
Abbreviation ContentsFLP(*1) Flowrate%PRV(*1) ProcessvalueVEL(*1) Flow velocityVFL(*1) VolumetricflowMFL(*1) MassflowFLB Flowratein%bargraphCAL(*1) CalorieTL1(*1) Totalizationvalue1TL2(*1) Totalizationvalue2TL3(*1) Totalizationvalue3TAG Tag No.LTG Long TagCOM CommunicationprotocolADH Adhesion diagnostic Level (Alarm at Level 4)AO1(*1) Analogoutputvalue1AO2(*1) Analogoutputvalue2FNL Flow Noise Level (Alarm at Level 4)
*1: Available to display the online trend graph.
2.2.2 BasicConfigurationforDisplayForparamtersettingfromdisplaypanel,configurableparametersdifferbythethreeoperationallevelsspecfiedinTable2.2.2,andapasscode is needed to enter into Setting mode. Nopasscoderequiresfor“Operator”,andapasscodecorrespondingtoeachlevelrequiresfor“Maintenance”or“Specialist”.For parameter in details, read Section 4.9.
Table 2.2.2 Parameter setting from display panel and operation level
Operation Level
Reading parameters
Writing parameters
Operator All parameters Parameters related with basic display settingsincludingdisplaylanguage.
Maintenance All parameters ParametersallowedforOperatorlevel.ParametersrelatedwithZeroadjustment.
Specialist All parameters All Parameters
Thefollowingparametersareavailableto“Operator”levelwithoutpasscode.
<2. Basic Operating Procedures> 11
IM 01E22A02-02EN
(1) Display Language SettingDisplayMenuPath:Devicesetup►Language
Thelanguageonthedisplayissetto“English”asdefaultatthefactoryshipment.Selecttheadequatelanguage.
Theselectabledisplaylanguageisdifferentbythemodelandsuffixcode(displaycode)specifiedwhen ordering.Positionofthedisplaycode:
Integral type:AXG--
Remote transmitter:AXG4A-
Display code Selectable display language1 English, French, German, Italian, Spanish,
Portuguese,Japanese,orRussian2 English or Chinese
(2) Display Contrast Setting (shading)DisplayMenuPath:Devicesetup►Detailedsetup►Displayset►Optionalconfig►Contrast
Availabletochangethecontrastofthedisplay.
Setting item Contents-5to+5 Setthecontrastofthedisplay
(Thevalueissmall:Low,andthevalueisbig:High)
(3) Display Line SettingDisplayMenuPath:Devicesetup►Detailedsetup►Displayset►Optionalconfig► Line mode
Availabletoselectthenumberoflinesofprocessvaluetobeindicatedonthedisplay.Uptofourlinescanbedisplayedatthesametime.The character size changes depending on the numberofline.
Setting item Contents1 line(big) Numberofdisplayableprocessvalue:One(without
unit)1 line Numberofdisplayableprocessvalue:One(withunit)2 line Numberofdisplayableprocessvalues:Two3 line Numberofdisplayableprocessvalues:Three4 line Numberofdisplayableprocessvalues:Four
Table 2.2.3 Display line setting and display exampleLines of display
Example 1 Example 2
1 line(big)F0202.ai
0.50000
00 : 00VEL
SET SFT INC
F0207.ai
00 : 00FNL
SET SFT INC
*Flownoisestatusisdisplayed. (Statuslabelisnotdisplayed.)
1 lineF0203.ai
0.50000
00 : 00VEL
SET SFT INC
m/s
F0208.ai
00 : 00FNL
SET SFT INCNormal
*Flownoisestatusandstatuslabel are displayed.
2 lineF0204.ai
0.500050.0
m/s
%
00 : 00VEL
SET SFT INC
FLP
F0209.ai
00 : 00FNL
SET SFT INC
NormalLong tag 123456789ABCDEFGabcdefg
LTG
*Indicate32charactersoftheLong Tag.
3 line F0205.ai
0.5000050.0
12.00
m/s%
mA
00 : 00VEL
FLPAO1
SET SFT INC
F0210.ai
00 : 00FNL
SET SFT INC
NormalLong tag 1234567...TAG12345
LTGTAG
*Indicate32charactersoftheLongTaginthefirstline.
* Indicate 16 characters in the firsthalfof32charactersoftheLong Tag in the second and third lines.
4 lineF0206.ai
0.5000050.0
12.000
m/s
%
mANormal
00 : 00VEL
AO1FNL
SET SFT INC
FLP
F0211.ai
00 : 00FNL
SET SFT INC
NormalLong tag 1234567...TAG12345
LTGTAG
* Indicate 16 characters in the firsthalfof32charactersoftheLong Tag only
(4) Date Display Formant SettingDisplayMenuPath:Devicesetup►Detailedsetup►Displayset►Optionalconfig► Format date
Thedatedisplayformatcanbespecifiedbelow.Setting item Contents
MM/DD/YYYY Displaysthedatein"month/day/year".DD/MM/YYYY Displaysthedatein"day/month/year".YYYY/MM/DD Displaysthedatein"year/month/day".
The date needs to be set every time when the poweristurnedon.In case the date is not set:• HARTcommunication:Datecountingstartsfrom1900/01/0100:00:00,accordingtoHARTspecification.
<2. Basic Operating Procedures> 12
IM 01E22A02-02EN
(5) Inverse Display SettingDisplayMenuPath:Devicesetup►Detailedsetup►Displayset►Optionalconfig►Inversion
Availabletochangefromnormaldiplaytowhite/black reverse display.
Setting item ContentsNormal Characters in the display is Black.Inverse Outlinecharacters
2.3 Display Mode and Setting Mode
ThedevicerunsintheDisplayModewhenthepoweristurnedon.Forcheckorchangeofparameters,theSettingModemustbeactivated.ThefollowingprocesureexplainshowtochangetotheSettingMode.ForthefunctionofIRswitches,readSubsection2.2.1.
[Procedure]1) Turnonthepowerandwaitforseveralseconds
to move to display mode.
F0212.ai
0.00000m/s0.00000l/min
00 : 00PRV
VEL
FLBSET SFT INC
2) Keeptouching[SET]switchfortwoseconds.ThescreenmovestothemenuofOperationLevel.
F0213.ai
Operation level Maintenance Specialist Exit
▲
▼
00 : 00
SET SFT INC
3) Select an appropreate operation level by movingthecursorwith[INC]or[DEC]switch. Passcodeisnotnecessaryfor“Operator”.For“Maintenance”and“Specialist”,passcodeisnecessaryforeach. Forpasscodesetting,[SFT]isforpositionchange,and[INC]isfornumber,thentwice[SET]isforentrycompletion. Thedefaultpasscodeatthefactoryshipmentissetto“0000”.
F0214.ai
Pass code **** 0000 0000 9999
00 : 00
SET SFT INC
4) WhentheOperationLevelisdetermined,thescreenmovesto“Devicesetup”astheSettingModewhereparameterscanbeconfigured.
5) Aftercompletingparametersetting,push[ESC]switch.ThescreenreturnstotheDisplayMode.
[PasscodeConfirmationandChange]Theconfirmationandchangeofthepasscodeareallowedonlybyparametersettingfromthedisplayunit.DisplayMenuPath:Devicesetup►Detailedsetup►Accesscfg►ChgmainteDevicesetup►Detailedsetup►Accesscfg►Chgspecial
(1) Passcodefor“Maintenance”operationlevel To change the passcode (Maintenance code), “Maintenance”or“Specialist”astheoperationallevelisrequired.
(2) Passcodefor“Specialist”operationlevel To change the passcode (Specialist code), “Maintenance”or“Specialist”astheoperationallevelisrequired.
IMPORTANTDisplayMenuPath:Devicesetup►Wizard
WhenparametersarechangedintheWizardofEasysetup,“Settingdownload”inthemenuofeachparametermustbeexecutedafterparameterischanged.Withouttheexecution,anyparameterchanged is not stored into the device.
NOTEIf10minutespastwithoutoperationintheSettingMode, the screen goes back to the Display Mode.
Parameter form
Therearethreetypesofparameterformbelow.Type Example of display Contents
Select type
F0215.ai
Unit m3
l(liter) cm3▲
▼
00 : 00
SET SFT INC
Selecttheadequatedatafromamongalternativeswhich are detemined in advance.
Numerictype
F0216.ai
Span +7200.00 +2200.00 +0.00001 +999999
00 : 00
SET SFT INC
Specifythedatawithacombinationofnumberandadecimal point into each digit.
Alphanumerictype
F0217.ai
Tag No FT-1234 FT-1234
00 : 00
SET SFT INC
Configurethedatawithacombinationofalphanumericcharacters. (Tag No., Special unit,etc…)
Thealphanumerictypeindicatesalphanumericcharactersinthefollowingorder.0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~"space"
<2. Basic Operating Procedures> 13
IM 01E22A02-02EN
2.4 Parameter Setting from Display Panel
Thissectionexplainshowtospecifytheparametersfromdisplaypanel.Select“Specialist”attheOperationLevelreferringtoSection2.3.AndselecttheparameterstobespecifiedintheSettingMode.
NOTEForthedevicewiththeorderinginformationspecifiedatordering,thespecifiedparameters(flowspanandunit,tagnumber,etc.)arestoredinthedeviceatthefactoryshipment.Withouttheorderinginformationspecified,parametersettingneedstobedonebyuser.
2.4.1 Setting example of Select type Data: Flow rate unit
ThefollowingistheprocedureofchangingtheflowrateunitasSelecttypeparameter.Theflowrateunitneedstobespecifiedwith“Physicalunit”and“Timeunit”individually.Whentheflowrateunitneedstobeset“l/min”,select“l(litter)”atthePhysicalunitand“/min”attheTimeunit.DisplayMenuPath:Devicesetup►Detailedsetup►Provar►Volume►UnitDevicesetup►Detailedsetup►Provar►Volume►TimeUnit
F0218.ai
Volume Damp pls/ttl Unit Time unit
▲
▼
00 : 00
SET SFT INC
SpecifythePhysicalunitforvolumetricflow.Movecursorwith[INC]and[DEC]accordingtothemenupathabove,andselectthe“unit”thenpush[SET].
F0219.ai
Unit m3
l(liter) cm3▲
▼
00 : 00
SET SFT INC
Movecursorwith[INC]and[DEC],andselectthe“l(liter)”thenpush[SET].Astheselectedunitisblinking,push[SET]todetermin.Thescreenreturnstothesettingpage.
F0220.ai
Volume Unit Time unit Span
▼
00 : 00
SET SFT INC
▲
SpecifytheTimeunitforvolumetricflow.Movecursorwith[INC]and[DEC]accordingtothemenupathabove,andselectthe“Timeunit”thenpush[SET].
F0221.ai
Time unit /s /min /h
▼
00 : 00
SET SFT INC
▲
Movecursorwith[INC]and[DEC],andselectthe“/min”thenpush[SET].Astheselectedunitisblinking,push[SET]todetermin.Thescreenreturnstothesettingpageafterthesetting.
F0222.ai
0.00000m/s0.00000l/min
00 : 00PRV
VEL
FLBSET SFT INC
Aftercompletingtheparametersetting,push[ESC]thenthescreenreturnstotheDisplayMode.
NOTEBesuretosettheFlowrateunitinthebeginningwhentheFlowrateunitandFlowspanvaluearechanged at the same time.Whentheunitischanged,thevalueofflowratespanisconvertedtorelatedvaluesautomaticallyaccordingtotheunitchange.
2.4.2 Setting example of Numeric type Data: Flow rate span
ThefollowingistheprocedureofchangingtheFlowratespanasNumerictypeparameter.DisplayMenuPath:Devicesetup►Detailedsetup►Provar►Volume►Span
NOTEBesuretosettheFlowrateunitinthebeginningwhentheFlowrateunitandFlowspanvaluearechanged at the same time.Whentheunitischanged,thevalueofflowratespanisconvertedtorelatedvaluesautomaticallyaccordingtotheunitchange.
F0223.ai
Volume Time unit /h Span +7200.00 Setting download
00 : 00
SET SFT INC
▲
▼
SpecifytheFlowratespanunit.Movecursorwith[INC]and[DEC]accordingtothemenupathabove,andselectthe“Span”thenpush[SET].
F0224.ai
Span +7200.00 +2200.00 +0.00001 +999999
00 : 00
SET SFT INC
Theswitch'sfunctionalityofsettingtheFlowrate span is as below: Plus/minusandmumericchange:[INC]Movement on digits: [SFT]Determinationofparameter:[SET]L:MinimumvalueU:MaximumvaluePush[SET]todecidewhilethevalueofFlowratespanisblinking.Thescreenreturnstothesettingpageafterthesetting.
<2. Basic Operating Procedures> 14
IM 01E22A02-02EN
2.4.3 Setting Example of Alphanumeric type Data: Tag No.
ThefollowingistheprocedureofchangingtheTagNo.asAlphanumerictypeparameter.DisplayMenuPath:Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►TagNo.
F0225.ai
Device info Date/Time Order info Ver/Num info
00 : 00
SET SFT INC
▲
▼
►
►
►
SpecifytheTagNo..Movecursorwith[INC]and[DEC]accordingtothemenupathabove,andselectthe“Orderinfo”thenpush[SET].
F0226.ai
Tag No FT-1234 FT-1234
00 : 00
SET SFT INC
ForTagNo.,upto8characterscanbeenteredfromdisplaypanel. Theswitch'sfunctionalityofsettingtheFlowrate span is as below: Plus/minusandmumericchange:[INC]Movement on digits: [SFT]Determinationofparameter:[SET]Available characters: ASCII charactersPush[SET]todecidewhilethevalueofTagNo.isblinking.Thescreenreturnstothesettingpageafterthesetting.
2.5 microSD Card Insertion/Removal
For the device with optional code MC, by setting the dedicated microSD card into the slot on the display unit,theparametersettingcanbestoredintoit.Thestored data can be restored to the device. For the detailedfunction,readChapter4.
WARNING
UseonlymicroSDcardssoldbyYOKOGAWA.Operationcannotbeguaranteedwhenothercardsareused.
(1) microSD Card InsertionCarefullyinsertthededicatedmicroSDcardintotheslotonthedisplayunituntiltheslotholdsthecard.(seeFigure2.5).
22.000mA0.0%
0.00000m/s
00 : 00VEL
FLP
AO1SET SFT INC
F0227.ai
microSD card
Figure 2.5 microSD Card Insertion
(2) microSD Card RemovalThemicroSDisremovedfromtheslotbypushingit.TopreventfromlosingthemicroSDcard,becarefulto handle the card.
IMPORTANTIfthemicroSDcardisremovedwithoutexecutionof“Unmount”onparametersetting,itmayresultinthecorruptionofstoreddataandtheabnormaloperationofdevice.
DisplayMenuPath:Devicesetup►microSD►Unmount
<3.OperationwithHARTConfigurationTool> 15
IM 01E22A02-02EN
3. OperationwithHARTConfigurationTool
ThischapterdescribestheconnectionofthisinstrumentandHARTconfigurationtool(FieldMate(VersatileDeviceManagementWizard)),andtheoperationusingHARTconfigurationtool.Readtheuser’smanualofFieldMate(IM01R01A01-01E)fordetailsabouttheFieldMate.
NOTE• FormoredetailsregardingtheoperationsoftheHARTconfigurationtool,readthemanualofHARTconfigurationtool.
• WhenusingFieldMate,besurethattherevision is R3.02.00 or later.
NOTEPerametersonHARTconfigurationtoolaredisplayedinEnglishonly.EvenifanylanguageotherthanEnglishisselectedas“displaylanguage”fromdisplaypanel,parametersaredisplayedinEnglishonHARTconfigurationtool.
3.1 Connecting the HART ConfigurationTool
TheHARTconfigurationtoolcaninterfacewiththisdevicefromthecontrolroom,thisdevicesite,or any other wiring termination point in the loop, providedthereisaminimumloadresistanceof230Ωbetweentheconnectionandthereceivinginstrument.Tocommunicate,itmustbeconnectedin parallel with this device, and the connections mustbenon-polarized.SeeFigure3.1.
F0301.ai
Iout+Iout-
USBFieldMate
Modem
USB
PC/FieldMate
Control Room
Magnetic FlowmeterTerminal Box Load
Resistance230 to 600 Ω
Relaying Terminals
4 to 20 mA DCSignal Transmission Line Terminal
Board Distributor
Figure3.1 ConnectingtheHARTConfigurationTool
IMPORTANTCommunicationsignalissuperimposedonanalogoutputsignal.Itisrecommendedtosetalow-passfilter(approximately0.1s)tothereceiverinordertoreducetheoutputeffectfromcommunicationsignal.Beforeonline-communication,confirmthatcommunicationsignaldoesnotgiveeffectontheuppersystem.
3.2 HARTConfigurationTooland Device Revision
IMPORTANTProtocolrevisionsupportedbyHARTconfigurationtoolmustbethesameprotocolrevisionorlaterthanthatofthedevice.Ifitisnot,communicationerroroccurs.
3.2.1 Device Description (DD) and Device Revision
BeforeusingtheHARTconfigurationtool,confirmthattheDD(DeviceDescription)ofthisdeviceisinstalledintheconfigurationtool. IfcorrectDDisnotinstalledtotheconfigurationtool,installacorrectDDfromtheHARTofficialsite,otherwise,contacttherespectivevendorsoftheconfigurationtoolforitsupgradeinformation.Thedevicerevisionisasfollows.DD Revision 1 or laterDevice Type AXG4A(0x371A)Device Revision 1
• ConfirmationofDDrevision(a) Turnonthepoweroftheconfigurationtool
underthestandalonecondition.(b) Confirmthedevicerevisionfromtheinstalled
DDfilenameaccordingtotheprocedureprovidedfortheconfigurationtool.
DDfilenameisfourdigits,uppertwodigitsaredevice revision and lower two digits are DD revision.
NOTEDevicerevisionofDDfileisgiveninhexadecimal.
<3.OperationwithHARTConfigurationTool> 16
IM 01E22A02-02EN
• ConfirmationofDevicerevisionConnecttheconfiguratortothisdeviceandconfirmtherevisionbythefollowingparameter.HARTCommunicationMenuPath:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►Flddevrev
3.2.2 Device Type Manager (DTM) and Device Revision
WhenconfiguretheparametersusingFieldMate,usetheDTM(DeviceTypeManager)readingthefollowingtable.DTM Name AXGHART7DTMDTM Revision 5.6.4.0 or later *Device Type AXG4A(0x371A)Device Revision 1
*: TheDTMisincludedinYokogawaDTMLibraryHART6.5or later.
NOTETheDTMrevisioncanbeconfirmedby“DTMsetup”.DeviceFilesisaMediaincludedinFieldMate.TheuserregistrationsiteprovidesDeviceFileswiththelatestupdateprograms.(URL:https://voc.yokogawa.co.jp/PMK/) Incaseupdate,followingoperationby“DTMsetup”isrequired.
• Update DTM catalog• Assign corresponding DTM to the device.Fordetails,readtheuser’smanualofFieldMate.
3.3 Basic SetupIfthededicatedparametersarespecifiedatthetimeofordering,thisinstrumentisshippedwiththetagnumberordeviceinformationconfigured.Thetagnumberanddeviceinformationcanbecheckedasfollows.
• Menu path of the tag number and device information
Item HART Communication Menu Path
Tag,Long tag
Devicerootmenu►Detailedsetup►Deviceinformation►Orderinformation►Tag,Longtag
Descriptor,Message,Date
Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►Descriptor,Message,Date
• Change of the tag number and device information
Entertheinformationwithinthefollowinglimitnumberofcharacters.
Item Limit number of charactersTag Upto8charactersornumbers*1
Long Tag Upto32charactersornumbers*2
Descriptor Upto16charactersornumbers*1
Message Upto32charactersornumbers*1
Date
mm/dd/yyyy(DD)yyyy/mm/dd(DTM)- mm: month (2 digits)- dd: days (2 digits)- yyyy: years (4 digits)
*1: Symbols,charactersandnumbersenclosedbyathicklineinthefollowingtableareavailable.
*2: Allsymbols,charactersandnumbersinthefollowingtableare available.
SP ! " # $ % & ' ( ) * + , - . /
0 1 2 3 4 5 6 7 8 9 : ; < = > ?
@ A B C D E F G H I J K L M N O
P Q R S T U V W X Y Z [ \ ] ^ _
` a b c d e f g h i j k l m n o
p q r s t u v w x y z { | } ~
*: "SP" means a space.
3.4 ParametersConfigurationTheparameterstructureoftheHARTconfigurationtool is hierarchical.Formenutreeandparameterindetails,readChapter 4 and Chapter 5.NotethatsomedisplayparametersaredifferentfromthoseofHARTconfigurationtools.
CAUTIONNotethatparametersettingbythedisplayunitisnotavailableinthemiddleofcommunicatingwithHARTconfigurationtool.
<3.OperationwithHARTConfigurationTool> 17
IM 01E22A02-02EN
HART Communication Menu Path:Uploadvariables►(seebelow)Tag Total2failopts Basic model code Watchdogresetexecuted
Long tag Total2 options Suffixconfig1 Voltageconditionsoutofrange
Descriptor Total2Start/Stop Suffixconfig2 Environmentalconditionsoutofrange
Message Total2presetvalue Option 1 Electronicfailure
Date Total2 set point Option 2 DeviceConfigurationLocked
Finalasmblynum Total3unit Option 3 StatusSimulationActive
Distributor Total3convfactor Option 4 DiscreteVariablesSimulationActive
Model Total3lowcut Remote sensor basic model code EventNotificationOverflow
Dev id Total3failopts Remotesensorsuffixconfig1 Secondary Analog Channel Saturated
Poll addr Total3 options Remotesensorsuffixconfig2 Tertiary Analog Channel Saturated
PV is Total3Start/Stop Remote sensor option 1 QuaternaryAnalogChannelSaturated
SV is Total3presetvalue Remote sensor option 2 QuinaryAnalogChannelSaturated
TV is Total3 set point Remote sensor option 3 Subdevicelistchanged
QVis Pulse1outputmode Remote sensor option 4 Duplicatemasterdetected
Alarm record mask 1 Frequency1at100%Fielddevicehasmalfunctionedduetoahardwareerrororfailure
Secondary Analog Channel Fixed
Alarm record mask 2 Statusoutput1function 10:MainboardCPUfailure Tertiary Analog Channel Fixed
Alarm record mask 3 Loopcurrentmode 11:Reversecalculationfailure QuaternaryAnalogChannelFixed
Alarmoutmask1 AO1lowcut*1 12:MainboardEEPROMfailure QuinaryAnalogChannelFixed
Alarmoutmask2 AO1 high limit 13:Main board EEPROM default
67:Pulseoutput1configurationerror
Alarmoutmask3 AO1 low limit 14:Sensorboardfailure 68:Pulseoutput2configurationerror
Alarmoutmask4 AO1alarmout 15:Sensorcommunicationerror 69:Nominalsizeconfigurationerror
Low alarm*1 AO1 range mode 16:A/D1failure[Signal] 70:Adhesionconfigurationerror
Low low alarm*1 Forward span 2*1 17:A/D2failure[Exciter] 71:Flownoiseconfigurationerror
*1: ThisparametercannotbedisplayedwithFDT2.0DTM.PossiblewithHARTbuilt-inDTM.
3.5 Data Renewing and Upload / Download Function
(1) Data RenewingThedataisautomaticallyupdatedat0.5to2second cycles.
(2) Upload / Download FunctionTheuploadfunctionisusedforcopyingtheparametersoftheinstrumenttoaHARTconfigurationtool.ThedownloadfunctionisusedforsettingthecopiedparametersintheHARTconfigurationtoolintootherinstrument.Theapplicableparametersarethefollowingsincludedin"Upload variables".
<3.OperationwithHARTConfigurationTool> 18
IM 01E22A02-02EN
Highalarm*1 Reverse_span1*1 18:Coil open 80:Analogoutput1saturated
Highhighalarm*1 Autorangehyst 19:Coil short 81:Analogoutput2saturated
Hi/Loalarmhysteresis Bi direction hyst 20:Exciterfailure 82:Pulseoutput1saturated
PVflowselect Flow direction 21:PWM1stop 83:Pulseoutput2saturated
Velocity check Display select1 22:PWM2stop 84:Analoginputsaturated
Velocityunit Display select2 23:Option board mismatch 85:Cable misconnect
Velocity span Display select3 24:Option board EEPROM failure 86:Coilinsulationwarning
VelocitydampingAO/frequency Display select4 25:OptionboardA/Dfailure 131:Transmitter type mismatch
Velocitydampingpulse/total Display select5 26:OptionboardSPIfailure 87:Adhesion over level 3
Timeunit Display select6 27:Parameter restore incomplete 88:Lowconductivitywarning
Volumeflowunit Display select7 28:Indicatorboardfailure 89:Insulationdetection
Volumeflowspan Display select8 29:Indicator board EEPROM failure 90:Flow noise over level 3
VolumeflowdampingAO/frequency Trend select 1 30:LCDdriverfailure 91:Flow noise over level 4
Volumeflowdampingpulse/total Trend select 2 31:Indicator board mismatch 92:Autozerowarning
Massflowunit Trend select 3 32:Indicatorcommunicationerror 93:Verificationwarning
Massflowspan Trend select 4 33:microSDfailure 94:Factory noise warning
MassflowdampingAO/frequency DisplayformatPV 50:Signaloverflow 95:Simulationactive
Massflowdampingpulse/total Displayformattotal1 51:Empty pipe detection 96:Analogoutput1fixed
Densityunit Displayformattotal2 52:H/LorHH/LLalarm 97:Analogoutput2fixed
Densityfixedvalue Displayformattotal3 53:Adhesion over level 4 98:Pulseoutput1fixed
Nominalsizeunit Display contrast 60:Spanconfigurationerror 99:Pulseoutput2fixed
Nominal size Display line 62:Analogoutput14-20mAlimit error 100:Analoginputfixed
User span select AO1 Display period 63:Analogoutput24-20mAlimit error 101:Parameterrestorerunning
UserunitAO1 Display NE107 64:Analogoutput1multirangeerror 102:Display over warning
User span AO1 Display alarm 65:H/LHH/LLconfigurationerror 103:microSD size warning
Total1unit Display scroll 66:Densityconfigurationerror 104:Parameterbackupincomplete
Total1convfactor Display damping Maintenancerequired 105:microSD card mismatch
Total1lowcut*1 Displayformatedate Device variable alert 106:microSD card removal procedureerror
Total1failopts Display inversion CriticalPowerFailure 120:Watchdog
Total1 options Language Failure 121:Poweroff
Total1Start/Stop Displaymeasuremode OutofSpecification 122:Instantpowerfailure
Total1presetvalue Display installation FunctionCheck 123:Parameterbackuprunning
Total1 set point Diagnosticoutput SimulationActive 124:Dataloggingrunning
Total2unit VF mode Non-VolatileMemoryfailure 130:Device ID not entered
Total2convfactor VF No Volatile Memory error
Total2lowcut Electrode size 72:Data logging not started
*1: ThisparametercannotbedisplayedwithFDT2.0DTM.PossiblewithHARTbuilt-inDTM.
HART Communication Menu Path:Uploadvariables►(seebelow)
<3.OperationwithHARTConfigurationTool> 19
IM 01E22A02-02EN
3.6 SpecificFunctionsofHARTConfigurationTool
3.6.1 Burst Mode(1) Applicable Parameter of Burst ModeWhentheBurstModeisenabled,theinstrumentcontinuouslysendsuptothreedataviaHARTcommunication.Alsoitispossibletosendalarmsignalcontinuouslywhenchangeinparametersettingorselfdiagnosisisdetected.
NOTEWhenchangingthesettingofBurstMode,set“Off”totheBurstmode.Defaultsettingis“Off”.
Command Parameter Burst Command Burst Message Trigger Mode Burst Trigger Source Burst Trigger Units
PV Cmd1: PV
Continuous --- ---Window
PV Depend on the assigned variable to PV
RisingFallingOn-change
LoopCurrentandPercentRange Cmd2:%range/current
Continuous --- ---Window
%range %RisingFallingOn-change
PV,SV,TV,QV Cmd3:Dynvars/current
Continuous --- ---Window
PV Depend on the assigned variable to PV
RisingFallingOn-change
Device Variable with status
Cmd9:Devicevarsw/status
Continuous --- ---Window
Process variable assigned tothetopofBurstDeviceVariables
Depend on the assigned variabletoBurstDeviceVariables
RisingFallingOn-change
Device Variable Cmd33: Device variables
Continuous --- ---Window
Process variable assigned tothetopofBurstDeviceVariables
Depend on the assigned variabletoBurstDeviceVariables
RisingFallingOn-change
AdditionalDeviceStatus Cmd48: Read Additional DeviceStatus
Continuous --- ---On-change Allstatus ---
<3.OperationwithHARTConfigurationTool> 20
IM 01E22A02-02EN
(2) Burst Mode SettingTheBurstModecanbespecifiedintheEasyBurstModeortheDetailedBurstMode.
• Setting of Easy Burst ModeTheEasyBurstModecansendoneBurstCommandcontinuously.TheEasyBurstModecanbeconfiguredwiththefollowingparameter.
HART Communication Menu Path:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►Burstsetup►Easyburstsetup►(seebelow)setEasyBurst SpecifyEasyBurstMode.
(BM0:BurstMessage0)
NOTEWhentheEasyBurstModeisused,theEventNotificationcannotbeused.
• Setting of Detailed Burst ModeTheDetailedBurstModecansenduptothreeBurstCommandscontinuouslyundervariousconditions.TheDetailedBurstModecanbeconfiguredwiththefollowingparameter.
HART Communication Menu Path:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►Burstsetup►Detailedburstsetup►(seebelow)BM1Setting►setDetailedBurst
SpecifyDetailedBurstMode.(BM1:BurstMessage1)
BM2Setting►setDetailedBurst
SpecifyDetailedBurstMode.(BM2:BurstMessage2)
BM3Setting►setDetailedBurst
SpecifyDetailedBurstMode.(BM3:BurstMessage3)
Inaccordancewiththemethod,specifythefollowings.• BurstCommand• UpdatePeriod/MaxUpdatePeriod• BurstMessageTriggerMode
(3) Burst Command SettingSelectthetransmissiondatafromtheBurstCommand.
Burst Command Command ParameterCmd1:PV PVCmd2:%range/current LoopCurrentandPercentRange
Cmd3:Dynvars/current PV,SV,TV,QV
Cmd9: Device vars w/status DeviceVariablewithstatus
Cmd33:Device Variables Device Variable
Cmd48:Read Additional Device Status
AdditionalDeviceStatus
(4) Burst Device Variables SettingWhen"Cmd9:Devicevarsw/status"or"Cmd33:DeviceVariables"isselectedasBurstCommand,itisrequiredtospecifytheBurstDeviceVariableswhichuptoeightvaluescanbespecifiedfor.Dev VarCode
Burst Device Variables
Dev VarCode
Burst Device Variables
0 Velocity 4 Totalizer 21 Volumeflow 5 Totalizer 32 Massflow 6 Flow noise3 Totalizer1 7 Calorificvalue
(5) Update Period/Max Update Period Setting
SpecifytheUpdatePeriod/MaxUpdatePeriodwhichistheupdateperiodofBurstMessageTrigger Mode. TheBurstTriggerSourceischeckedwithaperiodofUpdatePeriod,andifitfulfillstheconditionofBurstMessageTriggerMode,thedataisupdated.WhenitdoesnotfulfilltheconditionoftheTriggerModewithaperiodofUpdatePeriodandreachestheMaxUpdatePeriod,thedataisupdatedforcibly.
TheUpdatePeriod/MaxUpdatePeriodneedstobeselectedfromthefollowings.
Update Period/Max Update Period0.5 s 8 s1 s 16 s2 s 32 s4 s 60sto3600s(anyvalue)
NOTETotheUpdatePeriod,specifyavaluesmallerthanthe Max Update Period.
<3.OperationwithHARTConfigurationTool> 21
IM 01E22A02-02EN
(6) Burst Message Trigger Mode SettingSpecifyBurstMessageTriggerMode.When"Window","Rising"or"Falling"isselected,itisneededtospecifytheBurstTriggerLevel.
Burst Message Trigger Mode Description
Continuous BurstMessageistransmittedcontinuously.
WindowThetriggervaluemustbeapositivenumberandisthesymmetricwindowaroundthelastcommunicatedvalue.
RisingTheBurstMessagemustbetransmittedwhenthesourcevalueexceedsthethresholdestablishedbythetriggervalue.
FallingTheBurstMessagemustbetransmittedwhenthesourcevaluefallbelowthethresholdestablishedbythetriggervalue.
On-changeTheBurstMessagemustbetransmittedwhenthesourcevalueonchangeestablishedbythetriggervalue.
3.6.2 EventNotificationItispossibletosendalarmsignalcontinuouslywhenchangeinconfigurationorselfdiagnosisisdetectedasEvent.UptofiveEventoccurredcanbestoredasHistory.WhenEventNotificationisused,itisneededtospecifyDetailedBurstMessageandtoenableBurstMessage.
NOTENatethattheEventwhichisstoredasHistoryisdeletedwhenthepoweristurnedoff.
(1)EventNotificationSettingTheEventNotificationcanbeconfiguredwiththefollowingparameter.
HART Communication Menu Path:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►Eventsetup►(seebelow)set Event SpecifyEventNotification.*1
stop Event SpecifystoppingEventNotification.
*1: Fromthetablebelow,selectconfigurationoftheEventNotification.
Event Mask SpecifydevicestatustodetectEvent.(Event Mask)(Cmd48:ReadAdditionalDeviceStatus)
EventNotificationRetryTime
SpecifyperiodofEventNotificationwhenEventisoccurring.
Max Update Time SpecifyperiodofEventNotificationwhenEventdoesnotbeoccurring.
EventDebounceInterval
SpecifyminimumtimethatEventiscontinuing.
(2) Event AcknowledgmentIfaEventisoccurring,itisrequiredtoacknowledgeit.AcknowledgmentofEventcanbeconfiguredwiththefollowingparameter.
HART Communication Menu Path:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►Eventsetup►(seebelow)acknowledge Event SpecifyacknowledgmentofEvent.
NOTEAcknowledgment can be done only to the Event whichoccursfirstly.WhenmultipleEventsoccur,itisrequiredtoacknowledgeallofthem.
(3)EventNotificationFlowWhentheEventNotificationisenabled,astatuschangecausedbytheself-diagnosisoftheinstrumentwillalarmEvent1.Event1iscontinuouslytransmittedattheRetryTimeintervaluntilEvent1isacknowledged. IftheotherstatuschangeoccurredbeforeEvent1 acknowledgment, Event2 is kept internal andEvent1iscontinuouslytransmitteduntilEvent1acknowledgment.WhenEvent1wasacknowledged, Event1 disappears and Event2 is continuouslytransmitteduntiltheacknowledgment.WhenEvent2wasacknowledged,allEventswereacknowledgedandEventiscontinuouslytransmittedataintervaloftheMaxUpdateTime.
<3.OperationwithHARTConfigurationTool> 22
IM 01E22A02-02EN
3.6.3 Multidrop ModeWhenthemultidropmodepossibletoconnectmultipledevicesisused,thisinstrumentcanconnectupto63devicesonasinglecommunicationtransmissionline.Toactivatethemultidropmode,anumberfrom1to63mustbeassignedtothepollingaddress.Whenthemultidropmode is activated, it is also needed to change asettingofthe4to20mAanalogoutputsignalbecauseallthedataistransmittedindigitalone.Themultidropmodecanbeconfiguredbythefollowingprocedures.
(1) Polling Address SettingAssignanumberfrom1to63tothepollingaddress.
HART Communication Menu Path:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►(seebelow)Poll addr Specifypollingaddress.
NOTEWhenthesamepollingaddressissetfortwoormoredevicesinthemultidropmode,communicationwiththesedevicesisdisabled.
(2) Analog Output SettingUsually,fixananalogoutputsignalofmultidropmode to 4 mA. In this case, however, it is impossibletouseaburnoutoutput.Inthecaseoftheapplicationwhichreceivesandoperatesananalogoutputsignal,onevariableanalogoutputsignalcanbeusedforoneloop.Theanalogoutputofmultidropmodecanbeconfiguredwiththefollowingparameter.
HART Communication Menu Path:Devicerootmenu►Detailedsetup►Deviceinformation►HARTsetup►(seebelow)Loopcurrentmode Specifyanalogoutput.*1
*1: Fromthetablebelow,selectananalogoutputofmultidropmode.
Disabled Specifyanalogoutputto4mA(fixed).
Enabled Specifyanalogoutputto4to20mA(variable).
NOTETheanalogoutputsignalwhichisfixedbymultidropmodeisappliedonlytotheoutputofI/O1 terminal.
(3) Enabling Multidrop ModeConfigurethesettingsofpollingforareceivinginstrumentreferringtotheuser’smanualofeachHARTconfigurationtool.
(4) Communication in Multidrop Mode• WhenadeviceandaHARTconfigurationtoolstarttheconnection,thetoolsearchesforthedevicesetinthemultidropmode,thepollingaddress and the tag will be displayed.
• Afterthedesireddeviceisselected,normalcommunicationwiththeselecteddeviceispossible.Howeverthecommunicationspeedwill be slow.
(5) Release of Multidrop ModeToreleasethemultidropmode,theparameterneedstobeconfiguredasbelow.• Specifythepolingaddressof(1)to“0”.• Specifytheanalogoutputof(2)to"Enabled".
<4. Functions> 23
IM 01E22A02-02EN
4. FunctionsThischapterdescribeseachfunctionoftheinstrument.Thefollowingspresentanoverviewofeachfunction.
• Basic settingsThisinstrumentcanmeasuretheprocessvaluesoftheflowvelocity,volumetricflowrate,massflowrate,calorie,andflownoisesimultaneously.Inaddition,thedampingtimeconstantforeachprocessvaluecanbespecified.Fordetailsabouthowtocheckthemeasurementresultandthesettingprocedure,readSection4.1.
• Totalization functionThisinstrumenthasthreetotalizersfortheprocessvalues.Inadditiontothedisplaywiththetotalizedvalue,thetotalizerfunctionisprovidedtoscalethetotalizedvaluewiththeconversionfactorandcountaspecificflowrate.Also,ithasatotalizationswitchfunctionthatcomparesthespecifiedtargetvaluewiththetotalizedvaluetooutputtheresultwiththestatusoutput,andatotalizationpresetfunctionthatspecifiesthepresetvalue.Fordetailsaboutthetotalizationfunctionandsettingprocedure,readSection4.2.
• Pulse output, frequency output, and status output
Themeasurementresultcanbeoutputwithoneofthepulseoutput,frequencyoutput,orstatusoutput.Whenthepulseoutputisused,thepulsewidthorpulseratecanbeselected.Whenthefrequencyoutputisused,anoutputat0%or100%forthespanoftheprocessvaluecanbespecified.Whenthestatusoutputisused,thedevicestatuscanbeoutputwiththestatusoutput.Bothpulseoutputandfrequencyoutputcanbesettheirlowcutvalueeach.Fordetailsabouteachoutputandthesettingprocedure,readSection4.3.
• Status inputThestatusinputterminalisprovidedtousethetotalizerpresetfunctionorthezero-adjustmentfunctiondependingonanexternalstatusinput.Fordetailsaboutthesettingprocedure,readSection 4.4.
• Current output and current inputUptotwocurrentoutputsareavailable.Thesearethehigh/lowlimitfunction,forward/reverseflowratefunction(reverseflowrate:4to12mA,forwardflowrate:12to20mA),alarmoutputfunction,lowcutfunction,andotherfunctions.Thecurrentinputisusefulforinputtingthefluidtemperatureviaexternaltemperaturetransmitters.Fordetailsaboutthecurrentoutputandcurrentinputsettingprocedures,readSection4.5.
• Multi range functionThisfunctionperformstomakemeasurementswhileswitchingmultipleranges.Itispossibletoswitchtherangedependingontheflowrate,flowratedirection,orstatusinput.Fordetailsaboutthemultirangefunction,readSection 4.6.
• Auxiliary calculation functionThisfunctionperformstocalculatethetemperaturecorrectionforthedensityorthecaloriebyinputtingthetemperaturefromanexternalinstrumentwiththecurrentinput.Theaccuracyformassflowmeasurementgoesupbysettingthetemperaturecorrectionfordensity.Fordetailsabouttheauxiliarycalculationfunction,read Section 4.7.
• AlarmAdetectederrorcanbenotifiedasanalarmorwarning.ThisfunctionshowsitsstatusbasedonNAMURNE107tosuitparametersettings.Itisalsotorecordthepreviouslydetectedalarmsasahistoryandmaskunnecessaryalarmstodisappearthemfromthedisplay.Fordetailsaboutthealarmcontentsandthesettingprocedure,readSection4.8.
• DisplayThisdisplaysupportsmultiplelanguagestoselectthelanguagetobeusedonthedisplay.Also,thisfunctionshowsatimechangeoftheselectedparameter as a trend graph on the display.Fordetailsaboutthedisplaysettings,readSection4.9.
<4. Functions> 24
IM 01E22A02-02EN
NOTEThedefaultsettingofthelanguageisEnglishuponshipmentfromthemanufacturingplant.ChangethelanguagebyreferringtoSubsection2.2.2orSubsection4.9.1ifnecessary.Thisuser’smanualshowsEnglishatthemenupassofthedisplay.
• Device informationThisfunctionistochecktheparametersspecifiedatthetimeofordering,modelcode,andsuffixcodeofthisinstrumentonthedisplay.Fordetailsabouthowtocheckdeviceinformation,read Section 4.10.
• Diagnostic functionTherearemanykindsofdiagnosticfunctions,anditispossibletodiagnosefailureoftheinstrumentorprocessstatus.Forexample,thisfunctionisusefultodiagnosethehealthoftheinstrumentusingtheelectrodeadhesiondetectingfunction,sensoremptycheckfunction,ortheverificationfunction.Fordetailsaboutvariousdiagnosticfunctions,readSection 4.11.
• Test modeThismodeisarbitrarilytospecifytheprocessvalueorthevaluetobeoutputfromaconnectionterminalandtestaresponsefromthedevice.Fordetailsaboutthetestmode,readSection4.12.
• Backup, restore, and duplicate functions
Thebackupfunctioncanbestorethesettingparametersintothebuilt-inmemoryinthedisplay.IftheoptionalcodeMCisselected,thesettingparametersarestoredinthemicroSDcardsuppliedwiththisinstrumentinadditiontothebuilt-inmemory in the display.Thebackupdatacanbeusedtorestoresettingsintheinstrumentinwhichtheywerebackedup,orduplicatesettingstoanotherinstrument.Fordetailsaboutthebackup,restore,andduplicatefunctions,readSection4.13.
• Software write protection functionThesoftwarewriteprotectionfunctionfordisablingaparameterchangeisprovidedseparatelyfromthehardware write protection.Fordetailsaboutthesoftwarewriteprotectionfunction,readChapter4.14.
4.1 Basic Settings
4.1.1 OverviewThisinstrumentcansimultaneouslymeasuretheflowvelocity,volumetricflowrate,massflowrate,calorie,andflownoise.Themeasurementresultcanbeoutputasthecurrentoutput,frequencyoutput,pulseoutput,and/orstatusoutput.Thetablebelowshowsthecommunication/input-outputcodes,connectionterminals,andinputandoutputforeachterminal.Communication
and I/O code Connection TerminalHART I/O1 I/O2 I/O3 I/O4JA
Iout1 Active
P/Sout1Passive
- -
JB P/Sout2Passive
Iout2 Active
JC Sin No-voltage
Iout2 Active
JD Sout Passive
P/Sout2 Passive
JE Sin No-voltage
P/Sout2 Passive
JF Sin No-voltage
P/Sout2 Active
(Withresistor)
JG Sin No-voltage
P/Sout2 Active
(Withoutresistor)
JH Iout2 Passive
Iin Active
JJ P/Sout2Passive
Iin Active
JK Sin No-voltage
Iin Active
Iout1:CurrentoutputwithHARTcommunicationIout2:CurrentoutputIin:CurrentinputP/Sout1:PulseoutputorstatusoutputP/Sout2:PulseoutputorstatusoutputSin:StatusinputSout:StatusoutputThepositionofCommunicationandI/Ocode:
Integral Type:AXG--
Remote Transmitter:AXG4A-
NOTETheavailablefunctionsvarydependingontheconnection terminal type selected at the time ofordering.Needtoreadabovetablecarefullybeforeusewhichterminalisapplicabletoallocateeachfunction.
<4. Functions> 25
IM 01E22A02-02EN
4.1.2 PV Mapping of Process ValueThisfunctioncanallowsyoutomaptheflowvelocity,volumetricflowrate,massflowrate,andflownoiseastheprimaryvariable(PV).ThePV-mappedprocessvalueisoutputfromtheI/O1terminal.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Provar► PVflowselect►(seebelow)Velocity SetstheflowvelocitytothePrimary
Value.Volume Setsthevolumetricflowratetothe
PrimaryValue.Mass SetsthemassflowratetothePrimary
Value.Diag SetstheflownoisetothePrimaryValue.
HART communication:Devicerootmenu►Detailedsetup► Processvariables►PVflowselect►(seebelow)Velocity SetstheflowvelocitytothePrimary
Value.Volume Setsthevolumetricflowratetothe
PrimaryValue.Mass SetsthemassflowratetothePrimary
Value.Diag SetstheflownoisetothePrimaryValue.
4.1.3 Display of the Process ValueTheflowvelocity,volumetricflowrate,massflowrate,totalizedvalue,calorie,andflownoisecanbeviewedwiththefollowingparameters.
Display menu path:Devicesetup►Processvariables►(seebelow)Flowrate(%) Displaystherangeratefortheprocess
valuesettothePrimaryValue.Flow rate Displaystheprocessvaluesettothe
PrimaryValue.Velocity Displaystheflowvelocity.Volume Displaysthevolumetricflowrate.Mass Displaysthemassflowrate.Totalizer► Totalizer 1
Displaysthetotalizedvalueoftotalizer1.
Totalizer► Totalizer 2
Displaysthetotalizedvalueoftotalizer2.
Totalizer►Totalizer 3
Displaysthetotalizedvalueoftotalizer3.
Calorie Displays the calorie.
DisplayofflownoiseDevicesetup►Diag/Service►Diagnosis► Flownoise►Result►Value
HART communication:Processvariablesrootmenu► Dynamicvariables►(seebelow)PV Displaystheprocessvaluesettothe
PrimaryValue.PV%rnge Displaystherangeratefortheprocess
valuesettothePrimaryValue.
Processvariablesrootmenu► Devicevariables►(seebelow)Velocity Displaystheflowvelocity.Volumeflow Displaysthevolumetricflowrate.Massflow Displaysthemassflowrate.Totalizer1 Displaysthetotalizedvalueoftotalizer1.Totalizer2 Displaysthetotalizedvalueoftotalizer2.Totalizer3 Displaysthetotalizedvalueoftotalizer3.Calorificvalue Displays the calorie.Flow noise Displaystheflownoise.
4.1.4 Engineering Unit SettingTheunitcanbespecifiedfortheflowvelocity,volumetricflowrate,massflowrate,andcalorie.Eachparametercanbespecifiedusingthephysicalunitandtimeunit.For example, when setting "m3/h"asthevolumetricflowrate,specify"m3"(physicalquantity)and"h"(timeunit)individually.However,thetimeunitiscommonlysetregardlessofthekindsoffluid.Thetimeunitoftheflowvelocityisfixedto"/s",andtheunitoftheflownoiseto"cm/s",whichdonotrequiresettingstobemadebytheuser.Thesettingcanbeconfiguredwiththefollowingparameters.
Display menu path:PhysicalunitDevicesetup►Detailedsetup►Provar►(see below)Velocity►Unit Specifythephysicalunitoftheflow
velocity.Volume►Unit Specifythephysicalunitofthevolumetric
flowrate.Mass►Unit Specifythephysicalunitofthemassflow
rate.Calorie►Unit Specifythephysicalunitofthecalorie.
TimeunitDevicesetup►Detailedsetup►Provar►(see below)Volume►Timeunit Specifythetimeunitofthevolumetric
flowrate,massflowrate,orcalorie.Mass►TimeunitCalorie►Timeunit
<4. Functions> 26
IM 01E22A02-02EN
HART communication:PhysicalunitDevicerootmenu►Detailedsetup► Processvariables►(seebelow)Velocity► Velocityunit
Specifythephysicalunitoftheflowvelocity.
Volumeflow► Volumeflowunit
Specifythephysicalunitofthevolumetricflowrate.
Massflow► Massflowunit
Specifythephysicalunitofthemassflowrate.
Calorie► Calorificunit
Specifythephysicalunitofthecalorie.
TimeunitDevicerootmenu►Detailedsetup► Processvariables►(seebelow)Volumeflow► Timeunit
Specifythetimeunitofthevolumetricflowrate,massflowrate,orcalorie.
Massflow► TimeunitCalorie►Timeunit
4.1.5 Span SettingThespancanbespecifiedfortheflowvelocity,volumetricflowrate,massflowrate,calorie,andflownoise.However,thespanunitconformstothatspecifiedinSubsection4.1.4.Iftheunitischanged,thespanvalueischangedtothecorrespondingvaluesynchronouslywiththechangedunit.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Provar►(see below)Velocity►Span Specifythespanoftheflowvelocity.Volume►Span Specifythespanofthevolumetricflow
rate.Mass►Span Specifythespanofthemassflowrate.Calorie►Span Specifythespanofthecalorie.
Devicesetup►Diag/Service►Diagnosis►(see below)Flownoise►Span Specifythespanoftheflownoise.
HART communication:Devicerootmenu►Detailedsetup► Processvariables► (see below)Velocity► Velocity span
Specifythespanoftheflowvelocity.
Volumeflow► Volumeflowspan
Specifythespanofthevolumetricflowrate.
Massflow► Massflowspan
Specifythespanofthemassflowrate.
Calorie► Calorificflowspan
Specifythespanofthecalorie.
Diagnosticrootmenu►Diagnosis► (see below)Flownoise► Flow noise span
Specifythespanoftheflownoise.
NOTEBesuretonotethefollowingpointswhenspecifyingtheflowratespan.• Foralinewithasignificantflowchange,settheflowratespantothemaximumflowrate.Iftheflowrateexceedstheflowratespan,theflowrateerrorasitspercentageincreases.
• Foralinewiththestableflowrate,settheflowrate span to approximately 1.5 to 2.0 times towardthenormalflowrate.
• Specifytheflowrateforwhichtheflowvelocityisincludedwithintherangefrom0.3to10m/s.TheflowvelocitycanbecheckedusingthesizingdatadescribedinthegeneralspecificationsaslistedinTable1.1.Iftheflowvelocityischeckedusingtheparameter,itdisplaysthevalueobtainedbyconvertingthespecifiedflowratespantotheflowvelocity.
NOTEBesuretosettheflowrateunitinthebeginningwhenthespanvalueanditsflowrateunitarechanged at the same time.
<4. Functions> 27
IM 01E22A02-02EN
4.1.6 Damping Time Constant SettingThedampingtimeconstant(63.2%response)canbespecifiedfortheflowvelocity,volumetricflowrate,massflowrate,calorie,andflownoise.Whenreducinganoutputfluctuationorchangingtheresponse speed, change the damping time constant (defaultvalueas3.0seconds).Itispossibletomeasurethepulsingflowupto1Hzwiththevalueof0.1secondonthisfunctionincaseofapistonpump,etc...Thisfunctionisapplicabletospecifyeachoutputoftheprocessvalue(currentoutputorfrequencyoutput,andpulseoutputortotalizedvalue).However,thesettingvalueforflownoiseiscommonlyusedthesamevaluefromtheiroutputs.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Currentoutput/FrequencyoutputDevicesetup►Detailedsetup►Provar►(see below)Velocity► DampAO/F
Specifythedampingtimeconstanttowardflowvelocity.
Volume► DampAO/F
Specifythedampingtimeconstantofthevolumetricflowrate.
Mass►DampAO/F Specifythedampingtimeconstantofthemassflowrate.
Calorie► DampAO/F
Specifythedampingtimeconstantofthecalorie.
Pulseoutput/TotalizationDevicesetup►Detailedsetup►Provar►(see below)Velocity► Damppls/ttl
Specifythedampingtimeconstantoftheflowvelocity.
Volume► Damppls/ttl
Specifythedampingtimeconstantofthevolumetricflowrate.
Mass►Damppls/ttl Specifythedampingtimeconstantofthemassflowrate.
Calorie► Damppls/ttl
Specifythedampingtimeconstantofthecalorie.
• Flow noiseDevicesetup►Diag/Service►Diagnosis►(see below)Flownoise►Damp Specifythedampingtimeconstantofthe
flownoise.
HART communication:Currentoutput/FrequencyoutputDevicerootmenu►Detailedsetup► Processvariables►(seebelow)Velocity► VelocitydampingAO/frequency
Specifythedampingtimeconstantoftheflowvelocity.
Volumeflow► VolumeflowdampingAO/frequency
Specifythedampingtimeconstantofthevolumetricflowrate.
Massflow► MassflowdampingAO/frequency
Specifythedampingtimeconstantofthemassflowrate.
Calorie► CalorificvaluedampingAO/frequency
Specifythedampingtimeconstantofthecalorie.
Pulseoutput/TotalizationDevicerootmenu►Detailedsetup► Processvariables►(seebelow)Velocity► Velocitydampingpulse/total
Specifythedampingtimeconstantoftheflowvelocity.
Volumeflow► Volumeflowdampingpulse/total
Specifythedampingtimeconstantofthevolumetricflowrate.
Massflow► Massflowdampingpulse/total
Specifythedampingtimeconstantofthemassflowrate.
Calorie► Calorificvaluedampingpulse/total
Specifythedampingtimeconstantofthecalorie.
Flow noiseDiagnosticrootmenu►Diagnosis►(seebelow)Flownoise► Flow noise damping
Specifythedampingtimeconstantoftheflownoise.
NOTETheoutputfluctuationincreaseswhenthedampingtimeconstantissettolowervalue.Set the damping time constant to 5 seconds or longerforcontrolprocessingapplication.
<4. Functions> 28
IM 01E22A02-02EN
4.1.7 Low-cut Function SettingThelow-cutvaluecanbespecifiedforthecurrentoutput,frequencyoutput,pulseoutput,andtotalizer.Thefluctuationoutputattheflowrate“0”canbereducedwhenthisfunctionisused,becausetheoutputofthesetvalueorlessbecomes“0”forcibly.However,theunitoflow-cutvalueconformstothatspecifiedinSubsection4.1.4.Iftheunitischanged,thelow-cutvalueischangedtothecorrespondingvaluesynchronouslywiththechangedunit.Set"0"tothelow-cutvalueifitisunnecessarytousethisfunction.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:CurrentoutputDevicesetup►Detailedsetup►Analogout/in►(see below)AO1►Lowcut Specifythelow-cutvalueofcurrent
output1.AO2►Lowcut Specifythelow-cutvalueofcurrent
output2.
Frequencyoutput/PulseoutputDevicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►Lowcut Specifythelow-cutvalueoffrequency
output1orpulseoutput1.PO2/SO2►Lowcut Specifythelow-cutvalueoffrequency
output2orpulseoutput2.
TotalizationDevicesetup►Detailedsetup►Totalizer►(see below)Totalizer1►Lowcut Specifythelow-cutvalueoftotalizer1.Totalizer2►Lowcut Specifythelow-cutvalueoftotalizer2.Totalizer3►Lowcut Specifythelow-cutvalueoftotalizer3.
HART communication:CurrentoutputDevicerootmenu►Detailedsetup► Analogoutput/input►(seebelow)Analogoutput1►AO1lowcut
Specifythelow-cutvalueofcurrentoutput1.
Analogoutput2►AO2lowcut
Specifythelow-cutvalueofcurrentoutput2.
Frequencyoutput/PulseoutputDevicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1► Pulse1lowcut
Specifythelow-cutvalueoffrequencyoutput1orpulseoutput1.
Pulse/Statusoutput2► Pulse2lowcut
Specifythelow-cutvalueoffrequencyoutput2orpulseoutput2.
TotalizationDevicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1lowcut
Specifythelow-cutvalueoftotalizer1.
Totalizer2► Total2lowcut
Specifythelow-cutvalueoftotalizer2.
Totalizer3► Total3lowcut
Specifythelow-cutvalueoftotalizer3.
The hysteresis is set in each case in which the outputischangedto"0"throughthespecifiedlow-cutvalueandacaseinwhichtheoutputreturnstomeasuringvaluethroughthespecifiedlow-cutvalue.Thehysteresisineachcaseisobtainedasshown below.Fordetailsaboutthemultirangefunction,readSection 4.6.(1) Avaluewiththeoutputchangedto"0"through
thespecifiedlow-cutvalue =Low-cutvalue-(Minimumspanspecifiedin
multirangex0.5%)(2) Avaluewiththeoutputreturnedthroughthe
specifiedlow-cutvalue =Low-cutvalue+(Minimumspanspecifiedin
multirangex0.5%)
Example: Spanofvolumetricflowrate=10.0m3/h, Low-cutvalue=1.0m3/h Inthiscase,eachvalueisobtainedasshownbelow.(1) Thevaluewithoutputchangedto"0"through
thespecifiedlow-cutvalue = 1.0 [m3/h]–(10.0[m3/h]×0.5[%]) = 0.95 [m3/h](2) Thevaluewithoutputreturnedthroughthe
specifiedlow-cutvalue = 1.0 [m3/h]+(10.0[m3/h]×0.5[%]) = 1.05 [m3/h]
F0401.ai0
Output [m3/h]
1
Hysteresis1 %
Input [m3/h]1
(1)
(2)
1.050.95
<4. Functions> 29
IM 01E22A02-02EN
NOTENotethat,ifthelow-cutvalueislower,thetotalizationmightbecountedduetoaninfluenceofoutputfluctuationneartheoutput0%.Inparticular,iftheflowratespan,dampingtimeconstant,orconductivityissmallorlow,thetotalizationiseasilycountedwhentheflowrateis"0".Insuchacase,increasetheflowratespan,dampingtimeconstant,orlow-cutvalue.
NOTEWhentheoutputprocessvalueischanged,specifythelow-cutvalueagain.
4.1.8 Sensor’s Nominal Size SettingTo combine the remote transmitter with other remotesensor,thenominalsizeoftheremotesensormustbespecified.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Sensor►(see below)Nominalsizeunit Specifytheunitofthenominalsize.Nominal size Specifythenominalsize.
HART communication:Devicerootmenu►Detailedsetup► Sensor►(seebelow)Nominalsizeunit Specifytheunitofthenominalsize.Nominal size Specifythenominalsize.
NOTEFortheintegraltype,thenominalsizeanditsunithavebeensetatthefactoryshipment.Donotchange the these parameters.
4.1.9 Density SettingThedensitysettingisrequiredtomeasurethemassflowrate.Thedensitycanbeselectedfromthefixeddensityorthedensitycorrecteddependingonthetemperature.Fordetailsabouthowtomeasurethemassflowrate or correct the density depending on the temperature,readSubsection4.7.5.Itwillresultinasettingerrorthat“0”issettothedensityinthesituationofmappingthemassflowtoPV.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Provar►Density►(seebelow)Valueselect Selecttheuseofthetemperature-base
densitycorrectionfunction.*1Unit Specifytheunitofthedensity.Fixed density Specifythefixeddensityvalue.Std density Specifythereferencestandarddensity
valuetousethetemperature-basedensitycorrectionfunction.
Correct density Displays the corrected density.
HART communication:Devicerootmenu►Detailedsetup► Processvariables►Density►(seebelow)Densityvalueselect Selecttheuseofthetemperature-base
densitycorrectionfunction.*1Densityunit Specifytheunitofthedensity.Densityfixedvalue Specifythefixeddensityvalue.Standard density Specifythereferencestandarddensity
valuetousethetemperature-basedensitycorrectionfunction.
Correct density Displays the corrected density.
*1: Fromthetablebelow,selecttheuseofthetemperature-basedensitycorrectionfunction.
Fixedvalue Usesthefixeddensity(thedensityisnotcorrecteddependingonthetemperature).
Correctionvalue Uses the corrected density.
<4. Functions> 30
IM 01E22A02-02EN
4.1.10 Temperature SettingThetemperaturesettingisrequiredtocalculatethecaloriedependingonitsdifferencefromthetemperaturethatisinputviathecurrentinputprocess.Fordetailsaboutthecaloriemeasurement,readSubsection4.7.6.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Provar►Temperature► (see below)Stdtemperature Specifythereferencestandard
temperaturetousethetemperature-basedensitycorrectionfunction.
Meastemperature Displaysthetemperaturethatisinputfromcurrentinput.
Fixedtemperature Specifythereferencetemperaturetouseforthecaloriecaluculationbytemperaturedifferencefromthetemperaturewhichisinputfromcurrentinput.
HART communication:Devicerootmenu►Detailedsetup► Processvariables►Temperature►(seebelow)Standard temperature
Specifythereferencestandardtemperaturetousethetemperature-basedensitycorrectionfunction.
Measuredtemperature
Displaysthetemperaturethatisinputfromcurrentinput.
Calorificfixtemp Specifythereferencetemperaturetouseforthecaloriecalculationwhenthecurrentinputistemperaturesignal.
4.1.11 Zero AdjustmentZeroadjustmentiscarriedouttoensurethattheoutputforzeroflowis0%(i.e.,4mA).Althoughadjustmenttozeroisperformedatthemanufacturingplantpriortoshipment,thisproceduremustbecarriedoutonceagainfollowingtheinstallationofpipinginordertomatchthemagneticflowmetertoitsoperatingconditions.Thissubsectiondescribesthezeroadjustmentprocedureusingthedisplayunit.ForAXFA11,readtheapplicableuser’smanualaslistedinTable1.1.
IMPORTANT• Zeroadjustmentshouldbecarriedoutbeforeactualoperation.Notethatsettingandupdatefunctionscannotbecarriedoutduringthisprocedure(i.e.,forapproximately30seconds).
• Zeroadjustmentshouldonlybecarriedoutwhenthesensorhasbeenfilledwithmeasurementfluidandthefluidvelocityiscompletely zero by closing the valve.
• Eachtimethatthefluidbeingmeasuredischanged,itwillbenecessaryforzeroadjustmenttobecarriedoutforthenewfluid.
Aprocedureofexecutingzeroadjustmentisasfollows;DisplayMenuPath:Devicesetup►Diag/Service►Autozero►ExecuteDevicesetup►Diag/Service►Autozero►Result►Zerovalue
Enter the Setting Mode. (Read Section 2.3)
•Executionofzeroadjustment
F0402.ai
Device setup Process variables Diag/Service Easy setup wizard
▲
▼
00 : 00
SET SFT INC
►
►
►
Select“Diag/Service”accoridingtothemenupathabove.
F0403.ai
Diag/Service Verification Autozero AO/AI trim
▲
▼
00 : 00
SET SFT INC
►
►
►
Select“Autozero”.
F0404.ai
Autozero Execute Result▲
▼
00 : 00
SET SFT INC►
Select“Execute”.
F0405.ai
Execute Not execute Execute Not execute▲
▼
00 : 00
SET SFT INC
Select“Execute”.
<4. Functions> 31
IM 01E22A02-02EN
F0406.ai
Execute Execute
00 : 00
SET SFT INC
When“Execute”blinks,touch[SET]toexecute.
F0407.ai
Autozero functionexecuting...
00 : 00
00 : 08SET SFT INC
The time remaining until the end.
Autozerostarts,andtheprogressisdesplayed with a remaining time and a bargraph.Waitforthecompletion.
F0408.ai
Autozero Execute Result▲
▼
00 : 00
SET SFT INC►
AfterAutozerofinished,thedisplayreturnsto“Autozero”menu.
•Confirmationofzeroadjustmentresult
F0409.ai
Result Zero value ▲
▼
00 : 00
SET SFT INC
FortheresultofAutozero,select“Result”andthen“Zerovalue”.
F0410.ai
Zero value – 00.018cm/s – 00.018cm/s – 99.999 + 99.999
00 : 00
SET SFT INC
ResultofAutozeroisindicatedasontheleft.
NOTE
Whenthezeroadjustmentresultexceedsdefinedvalue,thewarning[092:AZwam]isindicated.
Zeroadjustmentcanbeexecutedwiththefollowingparameter.HARTCommunicationMenuPath:Devicerootmenu►Basicsetup►Autozero►AutozeroExe
4.2 Totalization Function
4.2.1 Totalized Value and Unit SettingThisfunctioncantotalizethevolumetricflowrate,massflowrate,andcalorie.Thisinstrumentprovidesthreetotalizers,whichcansimultaneouslyoperatethemforprocessvalues.Totalizer1isfortheprocessvaluePV-mappeddescribedinSubsection4.1.2.Totalizers2and3arefortheprocessvalueintheselectedunit.Thissettingcanbedisplayedandconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Totalizer►(see below)Totalizer1►Unit Displaystheunitoftotalizer1.Totalizer2►Unit Specifytheunitoftotalizer2.Totalizer3►Unit Specifytheunitoftotalizer3.
HART communication:Devicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1unit
Displaystheunitoftotalizer1.
Totalizer2► Total2unit
Specifytheunitoftotalizer2.
Totalizer3► Total3unit
Specifytheunitoftotalizer3.
NOTETheflowvelocitycannotbetotalized.IftheflowvelocityisselectedasthePrimaryValue,totalizer1obtainsthevolumetricflowrateandunitbasedon"m3".
<4. Functions> 32
IM 01E22A02-02EN
4.2.2 Totalized-Value Display and Totalizer Function
Thetotalizationresultcanbecheckedwiththetotalizedvalueoritsvaluewhichisscaledwiththeconversionfactor.Whenthetotalizedvalueisscaledwiththeconversionfactor,thespecifiedflowrateistotalizedin1-countincrements,whichcanbeusedasatotalizer.Thetotalizedvaluecanbedisplayedandspecifiedwiththefollowingparameters.
Display menu path:DisplayoftotalizedvalueDevicesetup►Detailedsetup►Totalizer►(see below)Totalizer 1 Displaysthetotalizedvalueoftotalizer1.Totalizer 2 Displaysthetotalizedvalueoftotalizer2.Totalizer 3 Displaysthetotalizedvalueoftotalizer3.
SettingoftheconversionfactorforscalingDevicesetup►Detailedsetup►Totalizer►(see below)Totalizer1► Convfactor
Specifytheconversionfactoroftotalizer1.
Totalizer2► Convfactor
Specifytheconversionfactoroftotalizer2.
Totalizer3► Convfactor
Specifytheconversionfactoroftotalizer3.
DisplayofthetotalizedvaluethatisscaledwiththeconversionfactorDevicesetup►Detailedsetup►Totalizer►(see below)Totalizer1count Displaysthescaledtotalized-valueof
totalizer 1.Totalizer2count Displaysthescaledtotalized-valueof
totalizer 2.Totalizer3count Displaysthescaledtotalized-valueof
totalizer 3.
HART communication:DisplayoftotalizedvalueProcessvariablesrootmenu► Devicevariables►(seebelow)Totalizer1 Displaysthetotalizedvalueoftotalizer1.Totalizer2 Displaysthetotalizedvalueoftotalizer2.Totalizer3 Displaysthetotalizedvalueoftotalizer3.
SettingoftheconversionfactorforscalingDevicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1convfactor
Specifytheconversionfactorof totalizer 1.
Totalizer2► Total2convfactor
Specifytheconversionfactorof totalizer 2.
Totalizer3► Total3convfactor
Specifytheconversionfactorof totalizer 3.
DisplayofthetotalizedvaluethatisscaledwiththeconversionfactorProcessvariablesrootmenu► Totalizercount►(seebelow)Totalizer1count Displaysthescaledtotalized-valueof
totalizer 1.Totalizer2count Displaysthescaledtotalized-valueof
totalizer 2.Totalizer3count Displaysthescaledtotalized-valueof
totalizer 3.
Example:Settheunitoftotalizer2to"m3" and the conversion factorto"2".→Ifthetotalizedvalueoftotalizer2issetto"10.123
m3",thetotalizedvalueisscaledto"10.123÷2=5".
4.2.3 Totalization Switch FunctionThetotalizationswitchfunctionisavailablewhenthetargetvalue(setpoint)tobetotalizedisspecifiedusingthetotalizationfunction.Thetotalizationswitchfunctioncomparesthespecifiedtargetvaluewiththetotalizedvaluetooutputtheresultwiththestatusoutput.Thestatusoutputisactivewhilethetotalizedvalueisoutofthespecifiedtargetvalue.Fordetailsabouttheoutput,activedirection,andstatusoutputfunctionsettingforeachterminal,readSection 4.3.Thissettingcanbeconfiguredwiththefollowingparameters.
<4. Functions> 33
IM 01E22A02-02EN
Display menu path:Devicesetup►Detailedsetup►Totalizer►(see below)Totalizer1► Set point
Specifythetargetvalueoftotalizer1.
Totalizer2► Set point
Specifythetargetvalueoftotalizer2.
Totalizer3► Set point
Specifythetargetvalueoftotalizer3.
HART communication:Devicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1 set point
Specifythetargetvalueoftotalizer1.
Totalizer2► Total2 set point
Specifythetargetvalueoftotalizer2.
Totalizer3► Total3 set point
Specifythetargetvalueoftotalizer3.
Example: Setting procedure to use the totalization switch function with the I/O2 terminal
FollowthestepsbelowtosetthestatusoutputoftheI/O2terminalto"Onactive"whenthetotalizedvalueoftotalizer1reachesthetargetvalue.(1) SettheoutputoftheI/O2terminalto"Status
out",referringtoSubsection4.3.1.(2) SettheactivedirectionoftheI/O2terminalto
"Onactive",referringtoSubsection4.3.4.(3) Setthestatusoutputfunctionto"Totallimit1",
referringtoSubsection4.3.7.(4) Specifythetargetvalueoftotalizer1,referring
tothissubsection.
4.2.4 Totalizer Operation at Alarm Occurrence
Thetotalizeroperationcanbespecifiedtodealwithanalarmthataffectsthetotalizationfunction.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Totalizer►(see below)Totalizer1► Failureopts
Specifythetotalizer1operationtobeperformedwhenanalarmhasoccurred.*1
Totalizer2► Failureopts
Specifythetotalizer2operationtobeperformedwhenanalarmhasoccurred.*1
Totalizer3► Failureopts
Specifythetotalizer3operationtobeperformedwhenanalarmhasoccurred.*1
HART communication:Devicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1failopts
Specifythetotalizer1operationtobeperformedwhenanalarmhasoccurred.*1
Totalizer2► Total2failopts
Specifythetotalizer2operationtobeperformedwhenanalarmhasoccurred.*1
Totalizer3► Total3failopts
Specifythetotalizer3operationtobeperformedwhenanalarmhasoccurred.*1
*1: Fromthetablebelow,selecttheoperationofthetotalizationfunction.
Run Continuesthetotalizationfunctionafteranalarmhasoccurred.
Hold Stopsthetotalizationfunctionafteranalarmhasoccurred.
Last valid Continuesthetotalizationfunctionwiththelastvalidvaluebeforeanalarmoccurs.
4.2.5 Totalization Function Start/Stop Setting
ThetotalizationfunctioncanbesettoStart/Stopmode.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Totalizer►(see below)Totalizer1► Start/Stop
SetsStart/Stoptothetotalizationfunctionoftotalizer1.
Totalizer2► Start/Stop
SetsStart/Stoptothetotalizationfunctionoftotalizer2.
Totalizer3► Start/Stop
SetsStart/Stoptothetotalizationfunctionoftotalizer3.
HART communication:Devicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1Start/Stop
SetsStart/Stoptothetotalizationfunctionoftotalizer1.
Totalizer2► Total2Start/Stop
SetsStart/Stoptothetotalizationfunctionoftotalizer2.
Totalizer3► Total3Start/Stop
SetsStart/Stoptothetotalizationfunctionoftotalizer3.
NOTEThetotalizationfunctionissetto"Stop"uponshipmentfromthemanufacturingplant.Tostartthetotalizationfunction,besuretosetitto"Start".
<4. Functions> 34
IM 01E22A02-02EN
4.2.6 Totalization Direction SettingThetotalizationdirectioncanbespecifiedtousethetotalizationfunction.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Totalizer►(see below)Totalizer1►Options Specifythetotalizationdirectionof
totalizer 1.*1
Totalizer2►Options Specifythetotalizationdirectionoftotalizer 2.*1
Totalizer3►Options Specifythetotalizationdirectionoftotalizer 3.*1
HART communication:Devicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1 options
Specifythetotalizationdirectionoftotalizer 1.*1
Totalizer2► Total2 options
Specifythetotalizationdirectionoftotalizer 2.*1
Totalizer3► Total3 options
Specifythetotalizationdirectionoftotalizer 3.*1
*1: From the table below, select the totalization direction.Balanced Totalizesthedifferentialflowratebetweenthe
forwardandreversedirections.Absolute Totalizestheabsolutevalueoftheflowrate.Only positive Totalizesonlytheflowrateintheforward
direction.Only negative Totalizesonlytheflowrateinthereverse
direction.Hold Stopstotalizationprocessing(holdsthecurrent
totalized-value).
4.2.7 Totalized Value Reset/Preset Function
Thereset/presetfunctioncanbespecifiedforthetotalizedvalue.Usingtheresetfunctionresetsthetotalizedvalueto"0".Usingthepresetfunctionsetsthetotalizedvalueinadvancetothepresetvalue.Thepresetfunctionisavailablewhenstartingcountingoftotalizationwiththespecifiedvalue.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Useofthereset/presetfunctionDevicesetup►Detailedsetup►Totalizer►(see below)Totalizer1► Reset/Preset
Usesthereset/presetfunctionof totalizer 1.*1
Totalizer2► Reset/Preset
Usesthereset/presetfunctionof totalizer 2.*1
Totalizer3► Reset/Preset
Usesthereset/presetfunctionof totalizer 3.*1
PresetvaluesettingDevicesetup►Detailedsetup►Totalizer►(see below)Totalizer1► Presetvalue
Specifythepresetvalueoftotalizer1.
Totalizer2► Presetvalue
Specifythepresetvalueoftotalizer2.
Totalizer3► Presetvalue
Specifythepresetvalueoftotalizer3.
HART communication:Useofthereset/presetfunctionDevicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1Reset/Preset
Usesthereset/presetfunctionof totalizer 1.*1
Totalizer2► Total2Reset/Preset
Usesthereset/presetfunctionof totalizer 2.*1
Totalizer3► Total3Reset/Preset
Usesthereset/presetfunctionof totalizer 3.*1
PresetvaluesettingDevicerootmenu►Detailedsetup► Totalizer►(seebelow)Totalizer1► Total1presetvalue
Specifythepresetvalueoftotalizer1.
Totalizer2► Total2presetvalue
Specifythepresetvalueoftotalizer2.
Totalizer3► Total3presetvalue
Specifythepresetvalueoftotalizer3.
*1: Fromthetablebelow,selectthereset/presetfunction.Notexecute Doesnotusethetotalizationvaluereset/preset
function.Reset Usesthetotalizationvalueresetfunction.Preset Usesthetotalizationvaluepresetfunction.
NOTETheparameterreturnsto"Notexecute"afterthetotalizationvaluereset/presetfunctionhasbeencompleted.
<4. Functions> 35
IM 01E22A02-02EN
4.3 Pulse Output, Frequency Output, and Status Output
4.3.1 Outputs of I/O2, I/O3, and I/O4 Terminals
TheI/O2,I/O3,andI/O4terminalscanbeusedasthepulseoutput,frequencyoutput,andstatusoutput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►Outputmode SpecifytheoutputoftheI/O2
terminal.*1
PO2/SO2►Outputmode SpecifytheoutputoftheI/O3orI/O4terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Pulse1outputmode
SpecifytheoutputoftheI/O2terminal.*1
Pulse/Statusoutput2►Pulse2outputmode
SpecifytheoutputoftheI/O3orI/O4terminal.*1
*1: Fromthetablebelow,selecttheoutputofeachterminal.Nofunction Doesnotusetheterminal.Fixedpulseoutput Setstheoutputtothefixedpulseoutput.Frequencyoutput Setstheoutputtothefrequencyoutput
(Duty50%).Statusoutput Setstheoutputtothestatusoutput.
Fordetailsaboutthestatusoutput,readSubsection4.3.7.
4.3.2 Pulse Output / Frequency Output Mapping
Theprocessvaluetobeoutputcanbeselectedtousethepulseoutputorfrequencyoutput.WhentheI/O2terminalisusedforoutput,theprocessvaluePV-mappedinSubsection4.1.2isoutput.WhentheI/O3orI/O4terminalisusedforoutput,theprocessvaluetobeoutputcanbeselectedfromtheflowvelocity,volumetricflowrate,massflowrate,calorie,andflownoise.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO2/SO2►Pulseselect SpecifytheoutputoftheI/O3or
I/O4terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput2►Pulse2select
SpecifytheoutputoftheI/O3orI/O4terminal.*1
*1: Fromthetablebelow,selecttheoutputoftheI/Oterminal.Non-Connect NooutputVelocity Setstheflowvelocitytotheoutput.Volumeflow Setsthevolumetricflowratetotheoutput.Massflow Setsthemassflowratetotheoutput.Calorie Setsthecalorietotheoutput.Diag Setstheflownoisetotheoutput.
<4. Functions> 36
IM 01E22A02-02EN
4.3.3 Pulse Width SettingThepulsewidthcanbeselectedtousethepulseoutput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►Fixwidth SpecifythepulsewidthoftheI/O2
terminal.*1
PO2/SO2►Fixwidth SpecifythepulsewidthoftheI/O3orI/O4terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Pulse1fixwidth
SpecifythepulsewidthoftheI/O2terminal.*1
Pulse/Statusoutput2►Pulse2fixwidth
SpecifythepulsewidthoftheI/O3orI/O4terminal.*1
*1: Fromthetablebelow,selectthepulsewidth.
Pulse width[ms]
Pulse rateMax.[pps]
Pulse width[ms]
Pulse rateMax.[pps]
0.05 10000 100 50.1 5000 200 2.50.5 1000 330 1.51 500 500 1.020 25 1000 0.533 15 2000 0.2550 10
4.3.4 Active Direction SettingWhetherthepulsesignalissetonorofftoenabletheactivemodecanbespecifiedwhenthepulseoutputorstatusoutputisused.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►Activemode Specifytheactivedirectionforthe
pulsesignaloftheI/O2terminal.*1PO2/SO2►Activemode Specifytheactivedirectionforthe
pulsesignaloftheI/O3orI/O4terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Pulse1activemode
SpecifytheactivedirectionforthepulsesignaloftheI/O2terminal.*1
Pulse/Statusoutput2►Pulse2activemode
SpecifytheactivedirectionforthepulsesignaloftheI/O3orI/O4terminal.*1
*1: Fromthetablebelow,specifytheactivedirectionofthepulsesignal.
Active:ON/Onactive SetstoActivewhenthepulsesignalisseton.Active:OFF/Offactive SetstoActivewhenthepulsesignalissetoff.
Example: Ifthefixedpulseoutputisspecifiedandthepulsewidth is set to "1 ms", Active is set as shown below.
F0411.ai
Active:ON
Active:OFF
1 ms
<4. Functions> 37
IM 01E22A02-02EN
4.3.5 Pulse Rate SettingThepulserateperpulseandthepulseratescalingcanbespecifiedtousethepulseoutputwhenthisfunctionisused.WhentheI/O2terminalisusedforoutput,theunitofthepulserateissettothatoftheprocessvaluePV-mappedinSubsection4.1.2.IncaseofusingtheI/O3orI/O4terminalforoutput,theunitofthepulserateissettothatoftheprocessvaluemappedinSubsection4.3.2.Thissettingcanbeconfiguredwiththefollowingparameters.Ifthepulseratescalingischanged,thepulseratevalueisalsochangedsynchronouslywiththechangedunit.
Display menu path:PulseratevalueDevicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►Ratevalue Specifythepulseratevalueofthe
I/O2terminal.PO2/SO2►Ratevalue Specifythepulseratevalueofthe
I/O3orI/O4terminal.
PulseratescalingDevicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►Rateunit Specifythepulseratescalingofthe
I/O2terminal.PO2/SO2►Rateunit Specifythepulseratescalingofthe
I/O3orI/O4terminal.
HART communication:PulseratevalueDevicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Pulse1ratevalue
SpecifythepulseratevalueoftheI/O2terminal.
Pulse/Statusoutput2►Pulse2ratevalue
SpecifythepulseratevalueoftheI/O3orI/O4terminal.
PulseratescalingDevicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Pulse1rateunit
SpecifythepulseratescalingoftheI/O2terminal.
Pulse/Statusoutput2►Pulse2rateunit
SpecifythepulseratescalingoftheI/O3orI/O4terminal.
Note: Fromthetablebelow,selectthepulseratescaling.nUnit/P 10-9×UnitperpulseuUnit/P 10-6×UnitperpulsemUnit/P 10-3×UnitperpulseUnit/P 1unitperpulsekUnit/P 103×UnitperpulseMUnit/P 106×UnitperpulsenP/Unit 10-9×UnitperpulseuP/Unit 10-6×UnitperpulsemP/Unit 10-3×UnitperpulseP/Unit 1pulseperunitkP/Unit 103×PulseperunitMP/Unit 106×Pulseperunit
*Unit:Indicatestheunitoftheprocessvaluetobeoutputasthepulseoutput.
NOTEThemaximumpulserateandpulsewidthmustbespecifiedsothatthefollowingconditionsaresatisfied.Maximumpulseratevalue[pps]=Flowratespan(Unit/s]xPulserate[P/Unit]≤10[kpps]≤1/(Pulsewidth×2)
Example:Whenthepulsewidthissetto"0.1ms",themaximumpulseratevalueissetto"1/(0.0001×2)=5000[pps]".Ifthespecifiedpulserateexceedsthisvalue,itcausesasettingerror,andanalarmisdisplayed.
<4. Functions> 38
IM 01E22A02-02EN
4.3.6 Frequency Output Range SettingWhenthefrequencyoutputisused,thefrequencyat0%and100%canbespecifiedforthespanoftheprocessvalue.Thefrequencyoutputrangecanbesetbyspecifyingthefrequency.WhentheI/O2terminalisusedforoutput,specifytheoutputfrequencyforthespanoftheprocessvaluePV-mappeddescribedinSubsection4.1.2.WhentheI/O3orI/O4terminalisusedforoutput,specifytheoutputfrequencyforthespanoftheprocessvaluemappeddescribedinSubsection4.3.2.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1► Frequencyat0%
Specifythefrequencywhen0%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O2terminal.
PO1/SO1► Frequencyat100%
Specifythefrequencywhen100%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O2terminal.
PO2/SO2► Frequencyat0%
Specifythefrequencywhen0%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O3orI/O4terminal.
PO2/SO2► Frequencyat100%
Specifythefrequencywhen100%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O3orI/O4terminal.
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Frequency1at0%
Specifythefrequencywhen0%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O2terminal.
Pulse/Statusoutput1►Frequency1at100%
Specifythefrequencywhen100%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O2terminal.
Pulse/Statusoutput2►Frequency2at0%
Specifythefrequencywhen0%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O3orI/O4terminal.
Pulse/Statusoutput2►Frequency2at100%
Specifythefrequencywhen100%issettotheprocessvaluethatistobeoutputwiththefrequencyoutputthroughtheI/O3orI/O4terminal.
4.3.7 Status Output Function SettingTheinstrumentstatuscanbesetasthecontactoutputtousethestatusoutput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► Pulse/Statusout►(seebelow)PO1/SO1►SO1function Specifythestatusoutput1function
oftheI/O2terminal.*1PO2/SO2►SO2function Specifythestatusoutput2function
oftheI/O3orI/O4terminal.*1PO3/SO3►SO3function Specifythestatusoutput3function
oftheI/O3orI/O4terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusoutput1►Statusoutput1function
Specifythestatusoutput1functionoftheI/O2terminal.*1
Pulse/Statusoutput2►Statusoutput2function
Specifythestatusoutput2functionoftheI/O3orI/O4terminal.*1
Statusoutput3► Statusoutput3function
Specifythestatusoutput3functionoftheI/O3orI/O4terminal.*1
<4. Functions> 39
IM 01E22A02-02EN
*1: Fromthetablebelow,selectthestatusoutputfunction.Nofunction Thestatusoutputisnotavailablebecausethe
statusoutputfunctionisnotenabled.Alarmoutput Thestatusoutputbecomesactivewhenan
alarmoccurs.Warningoutput Thestatusoutputbecomesactivewhena
warningoccurs.Total limit 1 Thestatusoutputisactivewhilethetotalized
valueoftotalizer1isoutofthespecifiedtargetvalue.Fordetailsaboutthetotalizationswitchfunction,readSubsection4.2.3.
Total limit 2 Thestatusoutputisactivewhilethetotalizedvalueoftotalizer2isoutofthespecifiedtargetvalue.Fordetailsaboutthetotalizationswitchfunction,readSubsection4.2.3.
Total limit 3 Thestatusoutputisactivewhilethetotalizedvalueoftotalizer3isoutofthespecifiedtargetvalue.Fordetailsaboutthetotalizationswitchfunction,readSubsection4.2.3.
H/Lalarm ThestatusoutputisactivewhilethePV-mappedprocessvalueisoutofthespecifiedlowlimitvalue(L)orhighlimitvalue(H).FordetailsaboutthePVmappingfortheprocessvalueandalarminformation,readSubsection4.1.2,Section4.8,andSubsection4.11.2.
HH/LLalarm ThestatusoutputisactivewhilethePV-mappedprocessvalueisoutofthespecifiedlow-lowlimitvalue(LL)orhigh-highlimitvalue(HH).FordetailsaboutthePVmappingfortheprocessvalueandalarminformation,readSubsection4.1.2,Section4.8,andSubsection4.11.2.
Fwd/Revrange Thestatusoutputisactivewhilethefluidisflowinginthereversedirection.Usedintheforward/reverserange.Fordetailsabouttheforward/reverserange,readSubsection4.6.4.
Auto2range Thestatusoutputisactivewhileoperationisbeingperformedinrange2.Usedinthemultirange.Fordetailsaboutthemultirangefunction,readSubsection4.6.3.
Ext2 answer Setsthestatusinputfunctiontotheexternalcontactrange.Thestatusoutputbecomesactivedependingonthein-userange.Usedforanswer-back(rangecheck)ofanexternalcontact range.Fordetailsaboutthestatusoutputfunctionandtheexternalcontactrange,readSubsection4.4.2 and 4.6.6.
4.4 Status Input
4.4.1 Active Direction Setting for Status Input
WhetherthestatusinputissetonorofftoenabletheactivemodecanbespecifiedwhentheI/O3terminalisusedforthestatusinput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Statusin►(see below)SI3►Activemode Specifytheactivedirectionofthe
statusinput.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Statusinput3► Statusinput3activemode
Specifytheactivedirectionofthestatusinput.*1
*1: Fromthetablebelow,selecttheactivedirectionofthestatusinput.
Active:ON/Short(On)act SetstoActivewhenthestatusinputisshort-circuited.
Active:OFF/Open(Off)act SetstoActivewhenthestatusinputisopened.
<4. Functions> 40
IM 01E22A02-02EN
4.4.2 Status Input Function SettingThestatusinputfunctionisavailablewhentheI/O3terminalisusedforthestatusinput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Statusin►(see below)SI3►Function Specifythestatusinputfunctionofthe
I/O3terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Pulse/Status►(seebelow)Pulse/Statusinput3► Statusinput3function
SpecifythestatusinputfunctionoftheI/O3terminal.*1
*1: Fromthetablebelow,selectthestatusinputfunction.Nofunction Thestatusinputisnotavailablebecausethe
statusinputfunctionisnotenabled.0%SignalLock Whenthestatusinputbecomesactive,the
currentoutput1oftheI/O1terminalisfixedto4 mA.
Extautozero Whenthestatusinputbecomesactive,thezeroadjustmentfunctionisperformedautomatically.Notethatthezeroadjustmentcannotbestoppedevenifthestatusinputischangedwhilethezeroadjustmentfunctionisrunning.
Total preset 1 Whenthestatusinputbecomesactive,thepresetvaluespecifiedinSubsection4.2.7isset to totalizer 1, and totalization starts with the value.
Total preset 2 Whenthestatusinputbecomesactive,thepresetvaluespecifiedinSubsection4.2.7isset to totalizer 2, and totalization starts with the value.
Total preset 3 Whenthestatusinputbecomesactive,thepresetvaluespecifiedinSubsection4.2.7isset to totalizer 3, and totalization starts with the value.
Ext2 ranges Whilethestatusinputisactive,therangeofcurrentoutput1isswitchedfromrange1torange 2. Used in the external contact range.Fordetailsabouttheexternalcontactrange,readSubsection4.6.6.
4.5 Current Input and Current Output
4.5.1 Current Output High/Low Limit Function
Thehigh/lowlimitfunctionisavailabletousethecurrentoutput.Usingthehigh/lowlimitfunctionrestrictsthehighlimitof4to20mAcurrentoutputandthelowlimitofthe4to20mAcurrentoutput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Analogout/in►(see below)AO1►Highlimit Specifythehighlimitvaluetousethe
I/O1terminalforthecurrentoutput.AO1►Lowlimit SpecifythelowlimitvaluetousetheI/O1
terminalforthecurrentoutput.AO2►Highlimit Specifythehighlimitvaluetousethe
I/O3orI/O4terminalforthecurrentoutput.
AO2►Lowlimit SpecifythelowlimitvaluetousetheI/O3orI/O4terminalforthecurrentoutput.
HART communication:Devicerootmenu►Detailedsetup► Analogoutput/input►(seebelow)Analogoutput1► AO1 high limit
SpecifythehighlimitvaluetousetheI/O1terminalforthecurrentoutput.
Analogoutput1► AO1 low limit
SpecifythelowlimitvaluetousetheI/O1terminalforthecurrentoutput.
Analogoutput2► AO2 high limit
SpecifythehighlimitvaluetousetheI/O3orI/O4terminalforthecurrentoutput.
Analogoutput2► AO2 low limit
SpecifythelowlimitvaluetousetheI/O3orI/O4terminalforthecurrentoutput.
Example:Ifthehighlimitvalueissetto16mAandthelowlimitvalueto8mAwhiletheI/O1terminalisusedforthecurrentoutput,theresultisasshownbelow.
F0412.ai
0
4
8
12
16
20
Time [sec]
Current [mA]
Low limit
High limitCurrent output before limit function applied.
<4. Functions> 41
IM 01E22A02-02EN
4.5.2 Absolute Range FunctionThecurrentoutputfunctionisavailabletousethecurrentoutput.Thecurrentsignalcanbeoutputbothforwardflowandreverseflowsimultaneouslytowardthespanwhenthisfunctionisused.Thecurrentoutputcanbeperformedbysettingtheflowrateof0%to12mA,thereverseflowrateto4to12mA,andtheforwardflowrateto12to20mA.However,thisfunctionisavailableonlywhentheI/O1terminalisusedforthecurrentoutput.Theabsoluterangefunctionandlowcutfunctioncanbeusedsimultaneously.Forlowcutfunction,readSubsection4.1.7.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Analogout/in►(see below)AO1►Rangemode Specifiestheuseoftheabsoluterange
functiontousetheI/O1terminalforthecurrentoutput.*1
HART communication:Devicerootmenu►Detailedsetup► Analogoutput/input►(seebelow)Analogoutput1► AO1 range mode
SpecifiestheuseoftheabsoluterangefunctiontousetheI/O1terminalforthecurrentoutput.*1
*1: Fromthetablebelow,selecttheuseoftheabsoluterangefunction.
Normal range Doesnotusetheabsoluterangefunction.Abs range Usestheabsoluterangefunction.
Example:(1) Absolute range without low-cut
F0413.ai-100
4
8
12
16
20
Flow rate [%]
Current [mA]
0 100
(2) Absolute range with low-cut
F0414.ai-100
4
8
12
16
20
Flow rate [%]
Current [mA]
0 100
Low cut
NOTETheabsoluterangefunctionandmultirangefunctioncannotbeusedsimultaneously.
4.5.3 Alarm Output FunctionThealarmoutputfunctionisavailabletousethecurrentoutput.Thecurrentsignalcanbeoutputforanoccurrenceofalarmwhenthisfunctionisused.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Analogout/in►(see below)AO1►Alarmout Specifythealarmoutputfunctiontouse
theI/O1terminalforthecurrentoutput.*1AO2►Alarmout Specifythealarmoutputfunctiontouse
theI/O3orI/O4terminalforthecurrentoutput.*1
HART communication:Devicerootmenu►Detailedsetup► Analogoutput/input►(seebelow)Analogoutput1► AO1alarmout
SpecifythealarmoutputfunctiontousetheI/O1terminalforthecurrentoutput.*1
Analogoutput2► AO2alarmout
SpecifythealarmoutputfunctiontousetheI/O3orI/O4terminalforthecurrentoutput.*1
*1: Fromthetablebelow,selecttheuseofthealarmoutputfunction.
<2.4mA Outputsthelowercurrentthan2.4mA.3.8 mA Outputsthe3.8mAcurrent.4 mA Outputsthe4mAcurrent.20.5 mA Outputsthe20.5mAcurrent.>21.6mA Outputsthehighercurrentthan21.6mA.Measuredvalue Outputsthemeasuredcurrent(thecurrent
valueisundefinedduetoanerror).Hold Outputsthecurrentthatisappliedwhenan
alarmhasoccurred.
<4. Functions> 42
IM 01E22A02-02EN
4.5.4 Current Output PriorityThepriorityofthecurrentoutputfunctionsvariesdependingonthesettingofthisinstrument.Thecurrentoutputisoperatedbasedonthefollowingprioritylevel.Priority
levelOutput mode
High
Low
HARTmultidropmode,4mAfixedcurrentoutput(Fordetails,readSubsection3.6.3.)Test mode(For details, read Section 4.12.)Statusinputfunction0%signallockoutput(Fordetails,readSubsection4.4.2.)Alarmoutputfunction(Fordetails,readSubsection4.5.3.)Verificationfunction,Outputduringofflinediagnosis(Fordetails,readSubsection4.11.6.)Normaloutput
4.5.5 Current Value Adjustment FunctionThecurrentvalueadjustmentfunctionisavailabletousethecurrentinputorcurrentoutput.Thecurrentinputvalueisadjustablewhen4.0mAforthe0%currentvalueisnotindicated,or20.0mAforthe100%currentvalueisnotindicated.Inaddition,thecurrentoutputisadjustablewhen4.0mAforthe0%currentvalueisnotindicated,or20.0mAforthe100%currentvalueisnotindicated.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:CurrentinputDevicesetup►Diag/Service►AO/AItrim►(see below)AItrim►Trim4mA Specifytheadjustmentvaluetousethe
I/O4terminalforthe4mAcurrentinput.AItrim►Trim20mA Specifytheadjustmentvaluetousethe
I/O4terminalforthe20mAcurrentinput.AItrim►Trimclear Clearstheadjustmentvaluetousethe
I/O4terminalforthecurrentinput.
CurrentoutputDevicesetup►Diag/Service►AO/AItrim►(see below)AO1 trim 4 mA Specifytheadjustmentvaluetousethe
I/O1terminalforthe4mAcurrentoutput.AO1 trim 20 mA Specifytheadjustmentvaluetouse
theI/O1terminalforthe20mAcurrentoutput.
AO1 trim clear ClearstheadjustmentvaluetousetheI/O1terminalforthecurrentoutput.
AO2 trim 4 mA SpecifytheadjustmentvaluetousetheI/O3orI/O4terminalforthe4mAcurrentoutput.
AO2 trim 20 mA SpecifytheadjustmentvaluetousetheI/O3orI/O4terminalforthe20mAcurrentoutput.
AO2 trim clear ClearstheadjustmentvaluetousetheI/O3orI/O4terminalforthecurrentoutput.
HART communication:CurrentinputMaintenancerootmenu►AO/AItrim► AItrim►(seebelow)AI trim Specifytheadjustmentvaluetousethe
I/O4terminalforthecurrentinput.Clear AI trim Clearstheadjustmentvaluetousethe
I/O4terminalforthecurrentinput.
CurrentoutputMaintenancerootmenu►AO/AItrim► AOtrim►(seebelow)AO1 trim Specifytheadjustmentvaluetousethe
I/O1terminalforthecurrentoutput.ClearD/Atrim1 Clearstheadjustmentvaluetousethe
I/O1terminalforthecurrentoutput.AO2 trim Specifytheadjustmentvaluetouse
theI/O3orI/O4terminalforthecurrentoutput.
ClearD/Atrim2 ClearstheadjustmentvaluetousetheI/O3orI/O4terminalforthecurrentoutput.
IMPORTANTIftheinputoroutputdoesnotmatchthespecifiedcurrentvaluewhenthecurrentvalueadjustmentfunctionisused,readjustthecurrentvalue.
<4. Functions> 43
IM 01E22A02-02EN
4.5.6 Current Input Function SettingTheoutputfromotherinstrumentcanbesetasthecurrentinputwhentheI/O4terminalisusedforthecurrentinput.Thecurrentinput,whichcanbeusedasthetemperatureinput,isavailablefortemperature-basedensitycorrectioncalculationandcaloriecalculation.Fordetailsaboutthetemperature-inputdensitycorrectioncalculationandcaloriecalculation,readSubsection4.7.5and4.7.6.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Analogout/in►(see below)AI►Function Specifythecurrentinputfunctionofthe
I/O4terminal.*1
HART communication:Devicerootmenu►Detailedsetup► Analogoutput/input►(seebelow)Analoginput► AIfunction
SpecifythecurrentinputfunctionoftheI/O4terminal.*1
*1: Fromthetablebelow,selectthecurrentinputfunction.Nofunction Thecurrentinputisnotavailablebecausethe
currentinputfunctionisnotenabled.Monitoring Monitoringofthecurrentinputisavailable.
However,thisfunctiondoesnotgiveanyinfluencesforneitherthedensitycorrectioncalculationnorthecaloriecalculation.
Difftemperature Usesthecurrentinputasatemperaturedifference.Thecaloriecalculationisavailable.
Exttemperature Usesthecurrentinputastheabsolutetemperature.Thedensitycorrectioncalculationandcaloriecalculationareavailable.
4.5.7 Current Input Range SettingTheinputvaluecanbespecifiedwiththe4mAor20mAcurrentvaluewhentheI/O4terminalisusedforthecurrentinput.Thecurrentinputrangecanbesetbyspecifyingitsinputvalue.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Analogout/in►(see below)AI►URV Specifythevaluethatisavailablewhen
20mAissettotheprocessvaluethatisinputwiththecurrentinputthroughtheI/O4terminal.
AI►LRV Specifythevaluethatisavailablewhen4mAissettotheprocessvaluethatisinputwiththecurrentinputthroughtheI/O4terminal.
HART communication:Devicerootmenu►Detailedsetup► Analogoutput/input►Analoginput►(seebelow)AI URV Specifythevaluethatisavailablewhen
20mAissettotheprocessvaluethatisinputwiththecurrentinputthroughtheI/O4terminal.
AI LRV Specifythevaluethatisavailablewhen4mAissettotheprocessvaluethatisinputwiththecurrentinputthroughtheI/O4terminal.
4.5.8 Current Input High/Low Limit Function
Thehigh/lowlimitfunctionisavailabletousethecurrentinput.Usingthehigh/lowlimitfunctionrestrictsthehighlimitof4to20mAcurrentinputandthelowlimitofthe4to20mAcurrentinput.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Analogout/in► (see below)AI►Highlimit Specifythehighlimitvaluetousethe
I/O4terminalforthecurrentinput.AI►Lowlimit SpecifythelowlimitvaluetousetheI/O4
terminalforthecurrentinput.
HART communication:Devicerootmenu►Detailedsetup► Analogoutput/input►Analoginput►(seebelow)AI high limit Specifythehighlimitvaluetousethe
I/O4terminalforthecurrentinput.AI low limit SpecifythelowlimitvaluetousetheI/O4
terminalforthecurrentinput.
<4. Functions> 44
IM 01E22A02-02EN
4.6 Multi Range Function
4.6.1 Multi Range TypesThemultirangefunctionisavailablewhenthecurrentoutputisperformedthroughtheI/O1terminalusingthestatusinputandstatusoutput.ThisfunctioncanbeperformedtomeasuretheflowratebyswitchingthespanoftheprocessvaluePV-mappedinSubsection4.1.2inmultipleranges.Themultirangefunctioncanbeselectedfromthemultirange,forward/reverserange,andexternalcontact range.Eachrangehasthefollowingfeature.Multirange Makesmeasurementswhileswitching
multiplerangesdependingontheflowrate,andoutputstherangestatusasthestatusoutput.
Forward/reverserange
Makesmeasurementswhileswitchingmultiplerangesdependingontheflowdirectionoftheflowrate,andoutputstherangestatusasthestatusoutput.
External contact range
Makesmeasurementswhileswitchingmultiplerangesdependingonthestatusinput.
NOTE• Themultirangefunctioncannotbeusedsimultaneouslywiththeabsoluterangefunction.
• ThemultirangefunctionisnotavailablewhentheI/O3orI/O4terminalisusedforthecurrentoutput.
4.6.2 Multi Range SettingThesettingforeachrangeisrequiredtousethemultirangefunction.Forinformationabouttheunitsetting,readSubsection4.1.4.Thissettingcanbeconfiguredwiththefollowingparameters.Fordetailsabouthowtospecifythespan(forwardrange1)withoutusingthemultirangefunction,readSubsection4.1.5.
Display menu path:Devicesetup►Detailedsetup►Multirange►(see below)Forward span 2 Specifyforwardrange2.Reverse span 1 Specifyreverserange1.Reverse span 2 Specifyreverserange2.
HART communication:Devicerootmenu►Detailedsetup►Multirange►(seebelow)Forward span 2 Specifyforwardrange2.Reverse span 1 Specifyreverserange1.Reverse span 2 Specifyreverserange2.
4.6.3 Multi Range OperationThemultirangefunctionperformstomakemeasurementswhileautomaticallyswitchingtworangesdependingontheflowrate.Ifthemeasuredflowrateishigherthanthelow-levelrange,itisautomaticallyswitchedtothehigh-levelrange.Ifthemeasuredflowrateislowerthanthehigh-levelrange,itisautomaticallyswitchedtothelow-levelrange.Thein-userangecanbeoutputasthestatusoutput.Therelationshipbetweentherangesandstatusoutputisasfollows.Low-level range Thestatusoutputisnotactive.High-levelrange Thestatusoutputisactive.
Whentherangeisswitchedfromthehigh-levelrange to the low-level range, the hysteresis is set. Thehysteresisspecifiestheratioforthelow-levelrange.Themultirangeswitchinghysteresiscanbespecifiedwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Multirange►(see below)Autorangehyst Specifythemultirangeswitching
hysteresis.
HART communication:Devicerootmenu►Detailedsetup► Multirange►(seebelow)Autorangehyst Specifythemultirangeswitching
hysteresis.
Themultirangecanbeconfiguredbythefollowingprocedure.(1) SpecifytheprocessvalueofthePrimaryValue,
referringtoSubsection4.1.2.(2) Specifythespan(forwardrange1),referringto
Subsection4.1.4and4.1.5.(3) Specifythemultirangeswitchinghysteresis.(4) Settheterminaloutputto"Statusout",referring
toSubsection4.3.1.(5) Setthestatusoutputfunctiontomultirange,
referringtoSubsection4.3.7.(6) Specifyforwardrange2,referringtoSubsection
4.6.2. Notethattheforwardrange2mustbesetwhich
islargervaluethantheforwardrange1.
<4. Functions> 45
IM 01E22A02-02EN
Example:PrimaryValue=Volumetricflowrate,Flow rate span (range 1) = 50 m3/h,Range 2 = 100 m3/h,Hysteresis=10%Inthiscase,thehysteresisvalueisobtainedasshown below. 50 [m3/h]×10[%]=5[m3/h](1) When the range is switched from low-level
range 1 to high-level range 2, the result is obtained as shown below.
F0415.ai
0
100
Status output
Output [%]
Flow rate [m3/h]
50 100
Forward range 1Forward range 2
(2) When the range is switched from high-level range 2 to low-level range 1, the result is obtained as shown below (with the hysteresis).
F0416.ai
0
100
Status output
Output [%]
Flow rate [m3/h]
50 10045
Forward range 1Forward range 2
NOTEReconfigurethemultirangesettingwhentheprocessvalueofthePrimaryValuespecifiedinSubsection4.1.2ischanged.
4.6.4 Forward/Reverse RangeTheforward/reverserangefunctioncanbeperformedtomakemeasurementswhileautomaticallyswitchingtheforwardandreverserangesdependingontheflowdirectionoftheflowrate.Theforwardorreverserangecanbespecifiedfortherange.Thein-userangecanbeoutputasthestatusoutput.Therelationshipbetweentherangesandstatusoutputisasfollows.Forward range Thestatusoutputisnotactive.Reverse range Thestatusoutputisactive.
Whentherangeisswitchedbetweentheforwardand reverse ranges, the hysteresis is set. The hysteresisspecifiestheratiofortheforwardorreverse range, whichever is lower.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Multirange►(see below)Bi direction hyst Specifytheforward/reverserange
switching hysteresis.
HART communication:Devicerootmenu►Detailedsetup►Multirange►(seebelow)Bi direction hyst Specifytheforward/reverserange
switching hysteresis.
Theforward/reverserangecanbespecifiedbythefollowingprocedure.(1) SpecifytheprocessvalueofthePrimaryValue,
referringtoSubsection4.1.2.(2) Specifythespan(forwardrange1),referringto
Subsection4.1.4and4.1.5.(3) Specifytheforward/reverserangeswitching
hysteresis.(4) Settheterminaloutputto"Statusout",referring
toSubsection4.3.1.(5) Setthestatusoutputfunctiontotheforward/
reverserange,referringtoSubsection4.3.7.(6) Specifyreverserange1,referringtoSubsection
4.6.2.
<4. Functions> 46
IM 01E22A02-02EN
Example:PrimaryValue=Volumetricflowrate,Flowratespan(forwardrange1)=50m3/h,Reverse range 1 = 100 m3/h,Hysteresis=5%Inthiscase,theforwardrangeissmallerthanthereverserange;therefore,thehysteresisvalueisobtainedasshownbelow. 50 [m3/h]×5[%]=2.5[m3/h]
(1) When the range is switched from the reverse range to the forward range, the result is obtained as shown below (with the hysteresis).
F0417.ai
-100
100
Status output
Output [%]
Flow rate [m3/h]0
Reverse range 1Forwardrange 1
502.5
(2) When the range is switched from the forward range to the reverse range, the result is obtained as shown below (with the hysteresis).
F0418.ai
-100
100
Status output
Output [%]
Flow rate [m3/h]0
Reverse range 1Forward range 1
50-2.5
NOTEReconfiguretheforward/reverserangesettingwhentheprocessvalueofthePrimaryValuespecifiedinSubsection4.1.2ischanged.
4.6.5 Combination of Multi Range and Forward/Reverse Range
Themultirangefunctioncanbecombinedwiththeforward/reverserangefunctionwhenthestatusoutput1functionoftheI/O2terminalandthestatusoutput2functionoftheI/O3orI/O4terminalaresettothemultirangefunctionandforward/reverserangefunctionrespectively.Twoforwardrangesandtworeverseranges,whicharefourrangestotally, can be assigned to each range.Thein-userangecanbeoutputasthestatusoutput.Therelationshipbetweentherangesandstatusoutputisasfollows.
○:Thestatusoutputisactive.×:Thestatusoutputisnotactive.
Multi range Forward/reverse range
Forward range 1 × ×Forward range 2 ○ ×Reverse range 1 × ○Reverse range 2 ○ ○
Themultirangeandforward/reverserangehavethehysteresisrespectively.Fordetailsaboutthehysteresisofthemultirangeandforward/reverserange,readSubsection4.6.3and4.6.4.
Thefollowingstepsaretocombinethemultirangewiththeforward/reverserange.(1) SpecifytheprocessvalueofthePrimaryValue,
referringtoSubsection4.1.2.(2) Specifythespan(forwardrange1),referringto
Subsection4.1.4and4.1.5.(3) Specifythehysteresisforthemultirangeand
forward/reverserange,referringtoSubsection4.6.3 and 4.6.4.
(4) Seteachterminaloutputto"Statusout",referringtoSubsection4.3.1.
(5) Setthestatusoutputfunctiontomultirangeorforward/reverserange,referringtoSubsection4.3.7.
(6) Specifytheforwardandreverseranges,referringtoSubsection4.6.2.
<4. Functions> 47
IM 01E22A02-02EN
4.6.6 External Contact RangeThisinstrumentenablesauseofanexternalcontactrange.Thisfunctioncanbemeasuredwhileautomaticallyswitchingtworangesdependingonthestatusinput.Therelationshipbetweentherangesandstatusinputisasfollows.Thestatusinputisnot active.
Low-level range
Thestatusinputisactive.
High-levelrange
Theexternalcontactrangecanbespecifiedbythefollowingprocedure.(1) SpecifytheprocessvalueofthePrimaryValue,
referringtoSubsection4.1.2.(2) Specifythespan(forwardrange1),referringto
Subsection4.1.4and4.1.5.(3) Setthestatusinputfunctiontotheexternal
contactrange,referringtoSubsection4.4.2.(4) Setthestatusoutputfunctiontotheexternal
contactrange,referringtoSubsection4.3.7.(5) Specifyforwardrange2,referringtoSubsection
4.6.2.
Example:PrimaryValue=Volumetricflowrate,Flowratespan(forwardrange1)=50m3/h,Forward range 2 = 100 m3/h Inthiscase,theresultisobtainedasshownbelow.
F0419.ai
Output [%]
Flow rate [m3/h]50 1000
100Forward range 2
Status input
Forward range 1
4.7 Auxiliary Calculation Function
4.7.1 Fluid Flow Direction SettingThearrowshownonthesurfaceofthesensorindicatesthefluidflowdirection.Uponshipmentfromthemanufacturingplant,theflowrateismeasured,assumingthatthearrowdirectionisforward.Thisinstrumentcanbechangedtheparametersettingandmeasuretheflowrate,assumingthattheoppositedirectionofthearrowdirectionisforward.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► AUXcalculation►(seebelow)Flow direct Specifythefluidflowdirection.*1
HART communication:Devicerootmenu►Detailedsetup► AUXcalculation►(seebelow)Flow direction Specifythefluidflowdirection.*1
*1: Fromthetablebelow,selectthefluidflowdirection.Forward Thearrowdirectionofthesensorisforward.Reverse Theoppositedirectionofthearrowdirectionof
thesensorisforward.
4.7.2 Rate Limit Function SettingTheratelimitfunctioncanperformtoreducenoisesthat cannot be all cleared by only lengthening the dampingtimeconstant.Whenastepsignalorasuddensignalduetoaslurryfluidisinput,thisfunctionjudgeswhetherthesignalisaflowratesignaloranoisesignal.Thisjudgmentismadebasedonthehigh/lowlimitvalue(ratelimitvalue)andtheratelimitfunctioncontinuationtime(deadtime),causingthenoisesignalovertheratelimitvaluetobecutoff.Theratelimitvalueisspecifiedwiththepercentage(%)forthespanoftheprocessvaluePV-mappedinSubsection4.1.2.Set"0"tothedeadtimeifthisfunctionisunnecessarytouse.Thissettingcanbeconfiguredwiththefollowingparameters.
<4. Functions> 48
IM 01E22A02-02EN
Display menu path:Devicesetup►Detailedsetup► AUXcalculation►(seebelow)Rate limit Specifytheratelimitvalue.Dead time Specifythedeadtime.Noisefilter Specifythenoisefilter(ratelimitvalue
and dead time).*1
HART communication:Devicerootmenu►Detailedsetup► AUXcalculation►(seebelow)Rate limit Specifytheratelimitvalue.Dead time Specifythedeadtime.Noisefilter Specifythenoisefilter(ratelimitvalue
and dead time).*1
*1: Fromthetablebelow,selectthenoisefilter(ratelimitvalueand dead time).
Rate limit value Dead timeManual Optional OptionalLevel 1 0.5% 0.5sLevel 2 1.0% 1.0sLevel 3 5.0% 3.0s
NOTEIfeithertheratelimitvalueorthedeadtimeisspecified,thenoisefilterissetto"Manual".
NOTEDetermining the rate limit value and dead time
F0420.ai
T0
T0
2%2%
The Rage limit value:Determine the level which should be cut the output fluctuation. For example, if its level is 2%, the noise of 2% or larger would be cut as shown in the following figure.
The Dead time (T0):Determine the value depending on the width of the output fluctuation. Choose the larger value when the noise which is over the dead time as shown in the following figure.
NOTEFortheratelimitfunction,thedeadtimeissetto"0"uponshipmentfromthemanufacturingplant.Besuretosetthedeadtimewhentheratelimitfunctionisused.
Signal processing for rate limit functionTheinstrumentcalculatestosetthespecificratelimitvaluetotheprimarydelayresponsevalueofthepreviouslysampledflowratevalue.Iftheflowratevaluesampledatthistimeexceedstheratelimitvalueabove,itshighorlowlimitvalueissettotheflowratevalueatthistime.Furthermore,ifthesamplingcountoccurswithinthedeadtimewhilethesignaloverthehigh/lowlimitvalueisinthesamedirection,thissignalisjudgedtobeaflowrate signal.
Example:(1) Input = 0 to 10%, Damping time constant = 5
seconds, Dead time = 3 seconds, Rate limit value = 1% In this case, the output for the step input is obtained as shown below.
F0421.ai
10%
1%
Step signal
Flow rate valueafter rate limitprocessing
63.2%
100 225Deat time: 3 s
(a) (b) (c) (d) Flow rate value after damping
Input: 0 to 10%Damping time constant: 5 sDead time: 3 sRate limit value: 1%
Number of signal samples
• In the condition above (a), the signal exceeds theratelimitvalueascomparedwiththepreviousvalue;therefore,theresponseissetto1%. Theactualoutput,whichisdamped,isprocessed as indicated by the solid line.
• Then,theflowratevalueinthedeadtimeissettothe"flowrateafterdampingcalculation+signalofratelimitvalue(1%)".
• Theinputsignaldoesnotreturntotheratelimitvalueorlesswithinthedeadtime;therefore,itisjudgedtobeaflowratesignalatthetimeof(c).
• Theoutputsignalstartsfollowingthestepsignalalongthedampingcurve.
<4. Functions> 49
IM 01E22A02-02EN
Thefigurebelowshowsanoutputexamplewhenaslurrynoisehasoccurred. (2) Input = 0 to 10%, Damping time constant
= 1 second, Dead time = 1 seconds, Rate limit value = 1% In this case, the output for a slurry noise is obtained as shown below.
F0422.ai
+1%
-1%
Dead time: 1 s
Flow rate value after damping
Flow rate valueafter rate limitprocessing
Slurry noise
Time
Input: 0 to 10%Damping time constant: 1 sDead time: 1 sRate limit value: 1%
In the figure on the left, it is determined that the slurries noise signal is not a flow rate signal.
4.7.3 Pulsing Flow Support Function Setting
Usingapump,etc.maycauseanerrorintheaverageoftheflowrateduetothepulsingflow.Ifthepulsingflowsupportfunctionisused,anerrorduetoapulsingflowcanbereducedbyfollowingaflowchangewhilecontrollingtheflowratecalculation.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► AUXcalculation►(seebelow)Pulsingflow Specifytheuseofthepulsingflow
supportfunction.*1
HART communication:Devicerootmenu►Detailedsetup► AUXcalculation►(seebelow)Pulsingflow Specifytheuseofthepulsingflow
supportfunction.*1
*1: Selecttheuseofthepulsingflowsupportfunctionfromthetable below.
No Donotusethepulsingflowsupportfunction.Yes Usethepulsingflowsupportfunction.
4.7.4 Power Frequency Synchronization Setting
Thisfunctioncanbespecifiedwhethertheexcitationfrequency(internalsignalprocessingfrequency)andpowerfrequencyaresynchronousorasynchronous.Whenmakingtheexcitationfrequencyandpowerfrequencyasynchronous,theexcitationfrequencyisdeterminedbythesetvalueofthepowerfrequency.Thepowerfrequencysynchronous/asynchronousmodeandthepowerfrequencycanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► AUXcalculation►(seebelow)Powersyncon/off Makestheexcitationfrequencyand
powerfrequencysynchronous.*1Setpowerfreq Setsthepowerfrequencywhen
theexcitationfrequencyandpowerfrequencyareasynchronous.
HART communication:Devicerootmenu►Detailedsetup► AUXcalculation►(seebelow)Power synchronize Makestheexcitationfrequencyand
powerfrequencysynchronous.*1Setpowerfrequency Setsthepowerfrequencywhen
theexcitationfrequencyandpowerfrequencyareasynchronous.
*1: Fromthetablebelow,selectthepowerfrequencysynchronous/asynchronousmode.
No Makestheexcitationfrequencyandpowerfrequencyasynchronous.
Yes Makestheexcitationfrequencyandpowerfrequencysynchronous.
IMPORTANTWhenusingtheDCpowerasthetransmitterpower, set the commercially available power frequencyoftheplacewheretousethetransmitter.Set"Powersyncon/off"toOffandspecify"Setpowerfreq".
<4. Functions> 50
IM 01E22A02-02EN
Theexcitationfrequencyandpowerfrequencycanbecheckedwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup► AUXcalculation►(seebelow)Iexpowerfrequency Displaysthepowerfrequency
(synchronouswiththeexcitationfrequency).
Measpowerfreq Displaysthemeasuredpowerfrequency.
HART communication:Devicerootmenu►Detailedsetup► AUXcalculation►(seebelow)Iexpowerfrequency Displaysthepowerfrequency
(synchronouswiththeexcitationfrequency).
Measuredpowerfrequency
Displaysthemeasuredpowerfrequency.
4.7.5 Density Correction CalculationWhenthetemperaturefromanotherinstrument(temperaturetransmitter,etc.)isusedasthecurrentinput,thedensitycorrectioncalculationcanbeperformeddependingonthetemperature.Usingthisfunctionleadstoenhancementofthemeasurementaccuracyforthemassflowrate.Transmitter
Iin-
Iin+24 V
0 V
Temperature transmitter, etc.
F0423.ai
Themassflowrateisobtainedinthefollowingexpression.Vm=Vf×ρ
Vm:Massflowrate[kg/s]Vf:Volumetricflowrate[m
3/s]ρ:Density[kg/m3]
Whenthedensitycorrectioncalculationisperformeddependingonthetemperature,thedensityisobtainedinthefollowingexpression.Thedensitycompensatingratesmustbespecifieddependingonapplicationsthatusethisinstrument.ρr=ρn×{1+a1×(Tr-Tn)×10
-2+a2×(Tr-Tn)2×10-6}
ρr:Densitycorrectedbasedonthemeasuredtemperature[kg/m3]
ρn:Standarddensity[kg/m3]
Tr:Measuredtemperature[°C]Tn:Standardtemperature[°C]a1: Primary compensating ratea2: Secondary compensating rate
Thestandardtemperatureandthecompensatingratescanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Provar►Temperature►(seebelow)CoefA1 Specifytheprimarycompensatingrate.CoefA2 Specifythesecondarycompensating
rate.
HART communication:Devicerootmenu►Detailedsetup► Processvariables►Temperature►(seebelow)TempcoefA1 Specifytheprimarycompensatingrate.TempcoefA2 Specifythesecondarycompensating
rate.
Thedensitycorrectioncalculationcanbesetinthefollowingsteps.(1) Settotheuseofthedensitycorrected
dependingonthetemperature,referringtoSubsection4.1.9.
(2) SetthecurrentinputoftheI/O4terminaltothetemperature,referringtoSubsection4.5.6.
(3) Specifytherangeofthecurrentinput,referringtoSubsection4.5.7.
(4) Specifythestandardtemperatureandstandarddensity,referringtoSubsection4.1.9and4.1.10.
(5) Specifytheprimarycompensatingrateandsecondarycompensatingrateofthecompensationformula.
NOTEThedensitycorrectioncalculationisperformedonlywhenitems(1)and(2)abovearespecified.Iftheyarenotspecified,thedensityisassignedtothefixedvaluethatisspecifiedinSubsection4.1.9.
<4. Functions> 51
IM 01E22A02-02EN
Example: Ifthewaterdensityiscorrectedbasedonthetemperatureinthefollowingconditions,theresultisobtained as shown below.Currentinputrange=0.0to100.0°C,Standarddensity=1000kg/m3,Standardtemperature=20°C,Primary compensating rate = -0.02, Secondary compensating rate = -3.9
F0424.aiTemperature [°C]
Den
sity
[kg/
m3 ]
950
960
970
980
990
1000
10 20 30 40 50 60 70 80 90 100
4.7.6 Calorie CalculationWhentheabsolutetemperatureorthetemperaturedifferencefromotherinstrument(temperaturetransmitter,etc.)isusedasthecurrentinput,thecaloriecalculationisexecutable.
Thecalorieisobtainedinthefollowingexpression.Q=c×Vm×∆t
Q:Calorie[J/s]C:Specificheat[J/kg•K]Vm:Massflowrate[kg/s]∆T:Temperaturedifference[K]
ThetemperaturedifferenceofΔtvariesdependingonthecurrentinputfunctionspecifiedinSubsection4.5.6.Ifthetemperaturedifferenceisselected,specifythetemperatureusedasthecurrentinput.Iftheabsolutetemperatureisselected,specifyadifferencebetweenthetemperatureusedasthecurrentinputandthereferencetemperaturespecifiedinSubsection4.1.10.[“Thetemperatureofbeingcurrentinput”–“Thereferencetemperatureofbeingset”]
Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Provar►Calorie►(seebelow)Specificheat Specifythespecificheat.
HART communication:Devicerootmenu►Basicsetup► Calorie►(seebelow)Specificheat Specifythespecificheat.
Thecaloriecalculationcanbeconfiguredbythefollowingprocedure.• When the absolute temperature is selected as
the current input:(1) SetthecurrentinputoftheI/O4terminaltothe
absolutetemperature,referringtoSubsection4.5.6.
(2) Specifytherangeofthecurrentinput,referringtoSubsection4.5.7.
(3) Specifythereferencetemperature,referringtoSubsection4.1.10.
(4) Specifythespecificheat.
• When the temperature difference is selected as the current input:
(1) SetthecurrentinputoftheI/O4terminaltothetemperaturedifference,referringtoSubsection4.5.6.
(2) Specifytherangeofthecurrentinput,referringtoSubsection4.5.7.
(3) Specifythespecificheat.
<4. Functions> 52
IM 01E22A02-02EN
4.8 Alarm
4.8.1 Errors and CountermeasuresTheerrormessagesarefollowingtable.ForAXFA11,readtheapplicableuser’smanualaslistedinTable1.1.
Ala
rm It
emD
escr
iptio
n
Syst
em A
larm
Devicebreaksdow
nandcausesabnormalmeasurement.Devicereplacem
entisneeded.
Proc
ess
Alar
mThedeviceworksnormallyandsom
eissueofprocesscausesabnormalmeasurement.Maintenanceworkisneeded.
Setti
ng A
larm
Thedeviceworksnormallybutparam
etersettingerroroccurs.Param
etersettingisneeded.
Warning
Thedeviceworksnormallyandmeasurementisalsonormalbutwarningoccurs.
Information
Thedeviceworksnormallyandmeasurementisalsonormal.Justreferenceinformation.
NE1
07 S
tatu
sSt
atus
of t
he D
evic
e
FFailure
Devicemalfunction,Partsmalfunction
CFunction Check
Theoutputsignalistemporarilyinvalidforthelocaloperationormanualoperation.
SOutofSpecification
Thedeviceworksinoutofspecification.Theoutputsignalisuncertainfortheprocessortheambience.
MMaintenanceRequired
Themaintenanceisrequiredinthenearfuture.
NNoEffect
Otherissue
Alar
m
Item
NE10
7St
atus
Erro
r Mes
sage
Erro
r Des
crip
tion
Coun
term
easu
re
Mes
sage
Coun
term
easu
re
Oper
atio
n at
the
time
of e
rror
Outp
utTo
tal
Proc
ess
Valu
eD
ispl
ayDi
spla
yH
AR
TDi
spla
yAl
arm
War
ning
Curre
ntPu
lse
/ St
atus
Syst
em
Alar
m
F01
0: M
ain
CPU
FAI
L10
Mai
n bo
ard
CPU
failure
CPU
(Mainboard)failurewas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
Burnout
Stop
Stop
Stop
Not
defined
F01
1: R
ev c
alc
FAIL
11R
ever
se
calculation
failure
Failureofreversecalculationwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F01
2: M
ain
EEP
FAIL
12M
ain
boar
d EE
PRO
M
failure
FailureofEEP
ROM(M
ainboard)
was
det
ecte
d.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Turnonthepoweragain
withinthetemperaturerange.
Iftheproblemdoesnot
impr
ove,
con
tact
Yok
ogaw
a se
rvic
e ce
nter
.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F01
3: M
ain
EEPdflt
13M
ain
boar
d EE
PRO
M
default
EEPR
OM
(Mai
n bo
ard)
was
resetedtodefaultvalues.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F01
4: S
nsr b
d FA
IL14
Sens
or b
oard
failure
Failureofsensorboardwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
F01
5: S
nsr
com
m E
RR
15Se
nsor
communica
tion
erro
r
Com
municationerrorofsensor
was
det
ecte
d.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
Burnout
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
F01
6: A
D 1
FA
IL[S
ig]
16A/D1
failure[Signal]
FailureofA/Dtransumitter1[flow
ve
loci
ty s
igna
l] w
as d
etec
ted.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
F01
7: A
D 2
FA
IL[E
xcit]
17A/D2
failure[Exciter]
FailureofA/Dtransm
itter2
[Excitingcurrent]w
asdetected.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
<4. Functions> 53
IM 01E22A02-02EN
Alar
m
Item
NE10
7St
atus
Erro
r Mes
sage
Erro
r Des
crip
tion
Coun
term
easu
re
Mes
sage
Coun
term
easu
re
Oper
atio
n at
the
time
of e
rror
Outp
utTo
tal
Proc
ess
Valu
eD
ispl
ayDi
spla
yH
AR
TDi
spla
yAl
arm
War
ning
Curre
ntPu
lse
/ St
atus
Syst
em
Alar
m
F01
8: C
oil
open
18C
oil o
pen
Coilofsensorw
asdisconnected.
Cutthepowerand
checkcoil&
EX
cabl
e.
Turnofthepow
er,check
coilo
fsensorandexcitation
cabl
e.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
F01
9: C
oil
shor
t19
Coi
l sho
rtCoilofsensorw
asshorted.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
F02
0: E
xcite
r FA
IL20
Exciterfailure
Failureofexcitationcircuitw
as
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F021:PWM1
stop
21PW
M1stop
Errorofpulsewidthmodulation1
was
det
ecte
d.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F022:PWM2
stop
22PW
M2stop
Errorofpulsewidthmodulation2
was
det
ecte
d.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
3: O
pt b
d m
ism
atch
23O
ptio
n bo
ard
mis
mat
chMismatchofoptionboardwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
4: O
pt b
d EE
P FA
IL24
Opt
ion
boar
d EE
PRO
M
failure
FailureofEEP
ROM(option
boar
d) w
as d
etec
ted.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
5: O
pt b
d A/DFAIL
25OptionboardA/
Dfailure
FailureofA/D(optionboard)was
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
6: O
pt b
d SP
I FAI
L26
Opt
ion
boar
d SP
Ifailure
FailureofSPI(optionboard)was
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
7: R
esto
re
FAIL
27Pa
ram
eter
re
stor
e in
com
plet
eRestoreofparam
eterswasfailed.
Ret
ry p
aram
eter
re
stor
atio
n.R
etry
par
amet
er re
stor
atio
n.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
8: In
d bd
FA
IL28
Indi
cato
r boa
rd
failure
Failureofindicatorboardwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Che
ck th
e am
bien
t temperatureofdisplay
iswithintherange.Ifthe
prob
lem
doe
s no
t im
prov
e,
cont
act Y
okog
awa
serv
ice
cent
er.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F02
9: In
d bd
EE
P FA
IL29
Indi
cato
r boa
rd
EEPR
OM
failure
FailureofEEP
ROM(indicator
boar
d) w
as d
etec
ted.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.
Turnonthepoweragain
withinthetemperaturerange.
Iftheproblemdoesnot
impr
ove,
con
tact
Yok
ogaw
a se
rvic
e ce
nter
.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F03
0: L
CD
drv
FA
IL30
LCD
driv
er
failure
FailureofLCDdriverwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F03
1: In
d bd
m
ism
atch
31In
dica
tor b
oard
m
ism
atch
MismatchofIndicatorboardwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F03
2: In
d co
mm
ER
R32
Indi
cato
r communica
tion
erro
r
Com
municationerrorofindicator
boar
d w
as d
etec
ted.
Che
ck c
onne
ctio
n ofIndicator&
main
boar
d.
CheckconnectionofIndicator
&mainboard.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
F03
3: m
icro
SD
FAIL
33m
icro
SD
failure
Failureofm
icroSD
cardwas
dete
cted
.C
hang
e m
icro
SD
card
.C
hang
e m
icro
SD c
ard.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
<4. Functions> 54
IM 01E22A02-02EN
Alar
m
Item
NE10
7St
atus
Erro
r Mes
sage
Erro
r Des
crip
tion
Coun
term
easu
re
Mes
sage
Coun
term
easu
re
Oper
atio
n at
the
time
of e
rror
Outp
utTo
tal
Proc
ess
Valu
eD
ispl
ayDi
spla
yH
AR
TDi
spla
yAl
arm
War
ning
Curre
ntPu
lse
/ St
atus
Proc
ess
Alar
m
S05
0: S
igna
l overflow
50Signaloverflow
Failureofinputsignalwas
dete
cted
.C
heck
sig
nal c
able
andgrounding.
Che
ck s
igna
l cab
le a
nd
grounding.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
S05
1: E
mpt
y de
tect
51Em
pty
pipe
de
tect
ion
Emptyinsideofsensorw
as
dete
cted
. (Em
pty
pipe
det
ectio
n)Fillflow
tubewith
fluid.
Fillflow
tubewithfluid.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Holdprior
setti
ngAl
arm
N052:H/LHH/
LL a
lm52
H/LorH
H/LL
alar
mFlow
rateexceededupperlimitor
low
er lim
it.Checkflow
rate
andsettingvalue.Checkflow
rateandsetting
value.
Activ
eN
on-
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Alar
m
S05
3: A
dh
over
lv 4
53Ad
hesi
on o
ver
leve
l 4
Theresistancevalueofthe
elec
trode
s ex
ceed
ed L
evel
4.
(Adhesiondetectionofinsulation
to e
lect
rode
)
Cle
an e
lect
rode
s.C
lean
ele
ctro
des.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
Setti
ng
Alar
m
S06
0: S
pan
cfgER
R60
Span
configuration
erro
r
Settingerro
rofflow
spanwas
dete
cted
. (fulfill"0.05m/s<Span<16m/s")
Cha
nge
span
pa
ram
eter
set
ting.
Che
ck o
r cha
nge
span
pa
ram
eter
set
ting.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
S06
2: A
O 1
4-
20 lm
t62
Analogoutput
1 4-
20 m
A lim
it er
ror
Settingerro
rofC
urrentoutput1
wasdetected.(fulfill"LR
V<HRV")C
hang
e An
alog
output1
para
met
er s
ettin
g.
Che
ck o
r cha
nge
Anal
og
output1param
etersetting.
Activ
eN
on-
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Alar
m
S06
3: A
O 2
4-
20 lm
t63
Analogoutput
2 4-
20 m
A lim
it er
ror
Settingerro
rofC
urrentoutput2
wasdetected.(fulfill"LR
V<HRV")C
hang
e An
alog
output2
para
met
er s
ettin
g.
Che
ck o
r cha
nge
Anal
og
output2param
etersetting.
Activ
eN
on-
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Alar
m
S06
4: A
O 1
mlt
rng
64An
alogoutput
1multirange
erro
r
Settingerro
rofM
ultirange
functionwasdetected.
(fulfill "1strange<=2ndrange"
andselect"eithermultirangeor
absoluterange".)
Changemulti
rang
e pa
ram
eter
se
tting
.
Checkorchangemultirange
para
met
er s
ettin
g.Ac
tive
Non
-Ac
tive
AlarmOut
Nor
mal
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
N065:H/Lcfg
ERR
65H/LHH/LL
configuration
erro
r
Settingerro
rofararmhigh/low
limitfunctionwasdetected.
(fulfill "HiAlarm-LoAlarm>H/L
Hys"and"H
HAlarm-LLAlarm>
HH/LLHys")
ChangeH/L,H
H/
LL p
aram
eter
se
tting
.
CheckandchangeH/L,H
H/
LL p
aram
eter
set
ting.
Activ
eN
on-
Activ
eAlarmOut
Nor
mal
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
S06
6: D
ensi
ty
cfgER
R66
Den
sity
configuration
erro
r
Settingerro
rofdensityvaluewas
dete
cted
whe
n PV
was
set
to
massflowrate.
Cha
nge
Den
sity
pa
ram
eter
set
ting.
Che
ck a
nd c
hang
e D
ensi
ty
para
met
er s
ettin
g.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
S067:Pls1cfg
ERR
67Pu
lse output1
configuration
erro
r
Settin
gerrorofPulseoutput1was
dete
cted
.
ChangePu
lse
output1
para
met
er s
ettin
g.
ChangePu
lseoutput1
para
met
er s
ettin
g.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Continue
Nor
mal
O
pera
tion
Alar
m
S068:Pls2cfg
ERR
68Pu
lseoutput2
configuration
erro
r
Settingerro
rofPulseoutput2
was
det
ecte
d.
ChangePu
lse
output2
para
met
er s
ettin
g.
CheckandchangePu
lse
output2param
etersetting.
Activ
eN
on-
Activ
eAlarmOut
AlarmOut
Continue
Nor
mal
O
pera
tion
Alar
m
<4. Functions> 55
IM 01E22A02-02EN
Alar
m
Item
NE10
7St
atus
Erro
r Mes
sage
Erro
r Des
crip
tion
Coun
term
easu
re
Mes
sage
Coun
term
easu
re
Oper
atio
n at
the
time
of e
rror
Outp
utTo
tal
Proc
ess
Valu
eD
ispl
ayDi
spla
yH
AR
TDi
spla
yAl
arm
War
ning
Curre
ntPu
lse
/ St
atus
Setti
ng
Alar
m
C06
9: N
omi
sizecfg
69N
omin
al s
ize
configuration
erro
r
Configurationerrorofnom
inal
size
was
det
ecte
d.
(fulfill"0.99mm<nom
inalsize<
3000.10mm(0.01inch<nom
inal
size<120.10inch)")
Cha
nge
nom
inal
pa
ram
ter s
ettin
g.C
heck
and
cha
nge
nom
inal
pa
ram
ter s
ettin
g.Ac
tive
Non
-Ac
tive
AlarmOut
AlarmOut
Base
d on
"F
ailO
pts"
Nor
mal
O
pera
tion
Alar
m
C070:Adhcfg
ERR
70Ad
hesi
on
configuration
erro
r
Settingerro
rofelectrode
adhesiondetectionfunctionwas
dete
cted
. (fulfill"Level1<Level2<Level3<
Leve
l4")
Cha
nge
adhe
sion
pa
ram
eter
set
ting.
Che
ck a
nd c
hang
e ad
hesi
on
para
met
er s
ettin
g.Ac
tive
Non
-Ac
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Alar
m
C071:FLN
cfg
ERR
71Fl
ow n
oise
configuration
erro
r
Settingerro
rofflow
noise
verificationfunctionwasdetected.
(fulfill"Level1<Level2<Level3<
Leve
l4")
Changeflownoise
para
mte
r set
ting.
Changeflownoiseparam
ter
setti
ng.
Activ
eN
on-
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Alar
m
C07
2: L
og n
ot
star
t72
Dat
a lo
ggin
g no
t sta
rted
Dataloggingfailedtostart.
Inse
rt m
icro
SD
card
.In
sert
mic
roSD
car
d.Ac
tive
Non
-Ac
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Alar
m
Warning
S08
0: A
O 1
saturate
80An
alogoutput
1saturated
SaturationofAnalogoutput1was
dete
cted
.C
heck
pro
cess
or
para
met
er s
ettin
g.
Checkprocessvalueand
curre
ntoutput1param
eter
setti
ng.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
S08
1: A
O 2
saturate
81An
alogoutput
2saturated
SaturationofAnalogoutput2was
dete
cted
.C
heck
pro
cess
or
para
met
er s
ettin
g.
Checkprocessvalueand
curre
ntoutput2param
eter
setti
ng.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
S08
2: P
ls 1
saturate
82Pu
lse output1
saturated
SaturationofPulseoutput1was
dete
cted
.C
heck
pro
cess
or
para
met
er s
ettin
g.
Checkprocessvalueand
pulseoutput1param
eter
setti
ng.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
S08
3: P
ls 2
saturate
83Pu
lseoutput2
saturated
SaturationofPulseoutput2was
dete
cted
.C
heck
pro
cess
or
para
met
er s
ettin
g.
Checkprocessvalueand
pulseoutput2param
eter
setti
ng.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
S08
4: A
I saturate
84An
aloginput
saturated
SaturationofAnaloginputw
as
dete
cted
.C
heck
pro
cess
or
para
met
er s
ettin
g.
Checkcurrentinputvalue
andcurre
ntinputparam
eter
setti
ng..
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
C08
5: C
able
m
isco
n85
Cab
le
mis
conn
ect
Misconnectionofcablewas
dete
cted
.
Checkthesignal/
EX
cabl
e co
nnec
tion.
Che
ck th
e si
gnal
cab
le a
nd
exci
tatio
n ca
ble
conn
ectio
n.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
C08
6: C
oil
insulation
86Coilin
sulation
war
ning
Insulationdeteriorationofcoilwas
dete
cted
.Coilin
sulationis
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
M08
7: A
dhes
ion
lv 3
87Ad
hesi
on o
ver
leve
l 3
Theresistancevalueofelectrode
exce
eded
Lev
el 3
. (Adhesiondetectionofinsulation
to e
lect
rode
)
Rec
omm
end
clea
ning
ele
ctro
deR
ecom
men
d cl
eani
ng
elec
trode
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
<4. Functions> 56
IM 01E22A02-02EN
Alar
m
Item
NE10
7St
atus
Erro
r Mes
sage
Erro
r Des
crip
tion
Coun
term
easu
re
Mes
sage
Coun
term
easu
re
Oper
atio
n at
the
time
of e
rror
Outp
utTo
tal
Proc
ess
Valu
eD
ispl
ayDi
spla
yH
AR
TDi
spla
yAl
arm
War
ning
Curre
ntPu
lse
/ St
atus
Warning
N08
8: L
C w
arn
88Lo
w
conductivity
war
ning
Decrease ofconductivitywas
dete
cted
.Fluidconductivity
is to
o lo
w.Checkfluidconductivity.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
M089:Insu
dete
ct89
Insulation
dete
ctio
nInsulationdeteriorationof
elec
trode
was
det
ecte
d.
Elec
trode
co
rrosi
on
dete
ctio
n w
arni
ng.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
N09
0: F
LN
over
lv 3
90Fl
ow n
oise
ove
r le
vel 3
Flow
noi
se e
xcee
ded
Leve
l 3.
(Detectionofflow
noise)
Checkthefluid.
Checkfluidconductivityor
bubble.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
N09
1: F
LN
over
lv 4
91Fl
ow n
oise
ove
r le
vel 4
Flow
noi
se e
xcee
ded
Leve
l 4.
(Detectionofflow
noise)
Checkthefluid.
Checkfluidconductivityor
bubble.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
C09
2: A
Z w
arn
92Au
tozero
war
ning
ResultofAutozeroadjustment
|MagFlowZero|exceeded10cm/
s.
Che
ck
envi
ronm
ent.
Checkfluidisstopped
whenexecutingauto-zero
adjustment.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
C093:Verif
war
n93
Verification
war
ning
Interru
ptionofverificationfunction
was
det
ecte
d.
LastVerification
wasinterru
pted.
ExecuteVerificationagain.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
C09
4: F
act
nois
e w
arn
94Fa
ctor
y no
ise
war
ning
fluctuationofflow
becam
elarger.Checkthefluid.
Checkthefluid.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
C09
5:
Simulate
activ
e95
Simulation
activ
e
Testmodewasexecutedforany
ofFlowvelocity,Volum
etricflow
rate,M
assflowrate,C
alorie,
Currentoutput,Pu
lseoutput,
Statusinput,Statusoutput.
Simulation
running.
Releasesimulationortest
mod
e.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
S096:AO1fix
96An
alogoutput
1fixed
Itwasdetectedthatfixiedvalueis
settoCurrentoutput1.
Plea
se c
ance
l thefixedoutput.
Checkcurrentoutput1istest
mod
e or
not
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
S097:AO2fix
97An
alogoutput
2fixed
Itwasdetectedthatfixiedvalueis
settoCurrentoutput2.
Plea
se c
ance
l thefixedoutput.
Checkcurrentoutput2istest
mod
e or
not
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
S098:Pls1fix
98Pu
lseoutput1
fixed
Itwasdetectedthatfixiedvalueis
settoPu
lseoutput1.
Plea
se c
ance
l thefixedoutput.
Checkpulseoutput1istest
mod
e or
not
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
S099:Pls2fix
99Pu
lseoutput2
fixed
Itwasdetectedthatfixiedvalueis
settoPu
lseoutput2.
Plea
se c
ance
l thefixedoutput.
Checkpulseoutput2istest
mod
e or
not
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
S100:AIfix
100An
aloginput
fixed
Itwasdetectedthatfixiedvalueis
settoCurrentinput.
Plea
se c
ance
l thefixedinput.
Checkcurrentinputistest
mod
e or
not
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
C10
1: P
aram
restorerun
101
Para
met
er
restore runningRestorefunctionofparam
eteris
running.
――
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Execute
N10
2: D
isp o
ver1
02D
ispl
ay o
ver
war
ning
Num
berofdigitsavailablefor
disp
lay
exce
eded
the
limit.
Che
ck D
ispl
ay
formatparam
eter.CheckDisplayformat
para
met
er.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
N10
3: S
D s
ize
war
n10
3m
icro
SD c
ard
size
war
ning
Freespaceofm
icroSD
card
decreasedtolessthan10%
.
mic
roSD
car
d m
ay
runoutofm
emory
spac
e.
microSD
cardmayrunoutof
mem
ory
spac
e.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Warning
<4. Functions> 57
IM 01E22A02-02EN
Alar
m
Item
NE10
7St
atus
Erro
r Mes
sage
Erro
r Des
crip
tion
Coun
term
easu
re
Mes
sage
Coun
term
easu
re
Oper
atio
n at
the
time
of e
rror
Outp
utTo
tal
Proc
ess
Valu
eD
ispl
ayDi
spla
yH
AR
TDi
spla
yAl
arm
War
ning
Curre
ntPu
lse
/ St
atus
Warning
M104:Bkup
incm
plt
104
Para
met
er
backup
inco
mpl
ete
Parameterbackupfailed.
Ret
ry p
aram
eter
backup.
Retryparam
eterbackup.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
S10
5: S
D
mis
mat
ch10
5m
icro
SD c
ard
mis
mat
chMismatchofm
icroSD
cardwas
dete
cted
.C
hang
e m
icro
SD
card
.C
hang
e m
icro
SD c
ard.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
M10
6: S
D
rem
oval
ER
R10
6m
icro
SD
card
rem
oval
procedureerrorR
emovalofm
icroSD
cardfailed.
Rem
ove
mic
roSD
in
app
ropr
iate
procedure.
Rem
ove
mic
roSD
in
appropriaterocedure.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Warning
N13
1: T
rans
m
ism
atch
131
Tran
smitt
er
type
mis
mat
chMismatchofsensorand
trans
mitt
er w
as d
etec
ted.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Nor
mal
Inform
ation
N12
0:
Watchdog
120Watchdog
ErrorofW
atchdoctim
erwas
dete
cted
.―
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Nor
mal
N12
1: P
ower
off
121Po
weroff
Power-offwasdetected.
――
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Nor
mal
N12
2: In
st
pow
er F
AIL
122
Inst
ant p
ower
failure
Instantaneouspowerfailurewas
dete
cted
.―
―N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Nor
mal
N12
3: P
aram
bkuprun
123
Para
met
er
backuprunningPa
rameterbackupisrunning.
――
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Execute
N12
4: D
ata
log
run
124
Dat
a lo
ggin
g running
Datalogisrunning.
――
Non
-Ac
tive
Activ
eN
orm
alN
orm
alContinue
Nor
mal
O
pera
tion
Icon
N13
0: D
evID
no
t ent
er13
0D
evic
e ID
not
en
tere
dNo dataentryofD
eviceIDwas
dete
cted
.C
onta
ct Y
okog
awa
serv
ice
cent
er.
Con
tact
Yok
ogaw
a se
rvic
e ce
nter
.N
on-
Activ
eAc
tive
Nor
mal
Nor
mal
Continue
Nor
mal
O
pera
tion
Nor
mal
<4. Functions> 58
IM 01E22A02-02EN
4.8.2 Alarm Display Setting(1) Alarm displayIfanerroroccursonthisinstrument,analarmappears on the display. The alarm display modes areclassifiedintotwotypes:modetodisplaytheprocessvalueandalarmname,andmodetodisplay the alarm name and action.Ifmultipleerrorsoccuronthisinstrument,thecorrespondingalarmsaredisplayedinsequenceonthe display.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Alarm display Sets the alarm display.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display alarm Sets the alarm display.*1
*1: From the table below, select the alarm display.Normal Displaystheprocessvalueandalarmname.
F0425.ai
01 : 00VEL
AO1FLP
SET SFT INC
0.00000m/s
mA4.000018: Coil open
0.0%
Detail Displays the alarm name and action.
F0426.ai
01 : 00
SET SFT INC
System Alarm
Cut the power andcheck coil & EX cable.
018: Coil open
(2) Alarm display based on NAMUR NE107Aprefixcanbeassignedtothealarmnamebasedon NAMUR NE107.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)NE107 display Sets the alarm display based on NAMUR
NE107.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display NE107 Sets the alarm display based on NAMUR
NE107.*1
*1: From the table below, select alarm display.Normal Sets to the normal alarm display.NE107 Sets the alarm display based on NAMUR
NE107.
4.8.3 Alarm History FunctionThealarmhistoryfunctionrecordsthepreviouslydetected alarms as a history.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►(seebelow)Record alarm 1 Displaysthenameofnewalarm1.Record time 1 Displays the operating time at which new
alarm1hasoccurred.Record alarm 2 Displaysthenameofnewalarm2.Record time 2 Displays the operating time at which new
alarm2hasoccurred.Record alarm 3 Displaysthenameofnewalarm3.Record time 3 Displays the operating time at which new
alarm3hasoccurred.Record alarm 4 Displaysthenameofnewalarm4.Record time 4 Displays the operating time at which new
alarm4hasoccurred.
<4. Functions> 59
IM 01E22A02-02EN
HART communication:Diagnosticrootmenu►Status/Selftest► Alarm►Alarmrecord►(seebelow)Alarm record 1 Displaysthenameofnewalarm1.Alarm record time 1 Displays the operating time at which new
alarm1hasoccurred.Alarm record 2 Displaysthenameofnewalarm2.Alarm record time 2 Displays the operating time at which new
alarm2hasoccurred.Alarm record 3 Displaysthenameofnewalarm3.Alarm record time 3 Displays the operating time at which new
alarm3hasoccurred.Alarm record 4 Displaysthenameofnewalarm4.Alarm record time 4 Displays the operating time at which new
alarm4hasoccurred.
Theoperatingtimeatalarmoccurrenceisdisplayedinformat,“dddddDhh:mm”.“dddddD”indicatestheday,“hh”indicatesthehour,and“mm”indicatestheminute.
Example: “00031D12:34”isdisplayed.Thisexampleshowsthatanalarmhasoccurredwhentheinstrumenthasoperatedfor31days,12hours,and34minutes.
4.8.4 Alarm Mask FunctionThealarmmaskfunctioncanmaskthespecifiedalarm,hideanalarmnotification,andrecordnoalarmhistory.Thisfunctioncanbesetforeachofthealarmnotificationandalarmhistory.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►(seebelow)Mask 1-1 Specifiesthemaskfunctionforalarm
notification1-1.Mask 1-2 Specifiesthemaskfunctionforalarm
notification1-2.Mask 2-1 Specifiesthemaskfunctionforalarm
notification2-1.Mask 2-2 Specifiesthemaskfunctionforalarm
notification2-2.Mask 3-1 Specifiesthemaskfunctionforalarm
notification3-1.Mask 3-2 Specifiesthemaskfunctionforalarm
notification3-2.Mask 4-1 Specifiesthemaskfunctionforalarm
notification4-1.
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecordmask►(seebelow)Mask 1-1 Specifiesthemaskfunctionforalarm
history 1-1.Mask 1-2 Specifiesthemaskfunctionforalarm
history 1-2.Mask 2-1 Specifiesthemaskfunctionforalarm
history 2-1.Mask 2-2 Specifiesthemaskfunctionforalarm
history 2-2.Mask 3-1 Specifiesthemaskfunctionforalarm
history 3-1.
HART communication:Diagnosticrootmenu►Status/Selftest► Alarm►Alarmoutmask►(seebelow)Alarmoutmask1 Specifiesthemaskfunctionforalarm
notification1.Alarmoutmask2 Specifiesthemaskfunctionforalarm
notification2.Alarmoutmask3 Specifiesthemaskfunctionforalarm
notification3.Alarmoutmask4 Specifiesthemaskfunctionforalarm
notification4.
Diagnosticrootmenu►Status/Selftest► Alarm►Alarmrecordmask►(seebelow)Alarm record mask 1 Specifiesthemaskfunctionforalarm
history 1.Alarm record mask 2 Specifiesthemaskfunctionforalarm
history 2.Alarm record mask 3 Specifiesthemaskfunctionforalarm
history 3.
NOTENote that the alarm masked by the alarm notificationmaskfunctionisnotrecordedinthealarm history.
<4. Functions> 60
IM 01E22A02-02EN
Thealarmmaskfunctionsettingisasfollows.Parameter name Indicatesthenameofthemasksettingparameter.
Alarm name Indicates the alarm name.Default value Indicatesthedefaultvalue(uponshipmentfromthemanufacturingplant).(○:Masked,-:Notmasked)
Attribute Indicateswhetherthemasksettingisenabledordisabled.(○:Enabled,-:Disabled)
(1) AlarmnotificationmaskfunctionDisplay HART
Parameter name Alarm name Default
value Attribute Parameter name Alarm name Default value Attribute
― 010: Main CPU FAIL ― ― ― 10 MainboardCPUfailure ― ―― 011: Rev calc FAIL ― ― ― 11 Reversecalculationfailure ― ―― 012: Main EEP FAIL ― ― ― 12 MainboardEEPROMfailure ― ―
Mask 1-1 013:MainEEPdflt ― Alarmoutmask1 13 MainboardEEPROMdefault ― ― 014: Snsr bd FAIL ― ― ― 14 Sensorboardfailure ― ―― 015: Snsr comm ERR ― ― ― 15 Sensorcommunicationerror ― ―― 016: AD 1 FAIL[Sig] ― ― ― 16 A/D1failure[Signal] ― ―― 017: AD 2 FAIL[Excit] ― ― ― 17 A/D2failure[Exciter] ― ―― 018: Coil open ― ― ― 18 Coil open ― ―― 019: Coil short ― ― ― 19 Coil short ― ―― 020: Exciter FAIL ― ― ― 20 Exciterfailure ― ―
Mask 1-2 021:PWM1stop ― Alarmoutmask1 21 PWM1stop ― Mask 1-2 022:PWM2stop ― Alarmoutmask1 22 PWM2stop ― Mask 1-2 023: Opt bd mismatch ― Alarmoutmask1 23 Option board mismatch ― Mask 1-2 024: Opt bd EEP FAIL ― Alarmoutmask1 24 OptionboardEEPROMfailure ― Mask 1-2 025:OptbdA/DFAIL ― Alarmoutmask1 25 OptionboardA/Dfailure ― Mask 1-2 026: Opt bd SPI FAIL ― Alarmoutmask1 26 OptionboardSPIfailure ―
― 027: Restore FAIL ― ― ― 27 Parameter restore incomplete ― ―Mask 1-2 028: Ind bd FAIL Alarmoutmask1 28 Indicatorboardfailure Mask 1-2 029: Ind bd EEP FAIL ― Alarmoutmask1 29 IndicatorboardEEPROMfailure ― Mask 1-2 030: LCD drv FAIL ― Alarmoutmask1 30 LCDdriverfailure ― Mask 1-2 031: Ind bd mismatch ― Alarmoutmask1 31 Indicator board mismatch ― Mask 1-2 032: Ind comm ERR ― Alarmoutmask1 32 Indicatorcommunicationerror ― Mask 1-2 033: microSD FAIL ― Alarmoutmask1 33 microSDfailure ― Mask 2-1 050:Signaloverflow ― Alarmoutmask2 50 Signaloverflow ― Mask 2-1 051: Empty detect ― Alarmoutmask2 51 Empty pipe detection ― Mask 2-1 052:H/LHH/LLalm Alarmoutmask2 52 H/LorHH/LLalarm Mask 2-1 053: Adh over lv 4 Alarmoutmask2 53 Adhesion over level 4 Mask 2-1 060:SpancfgERR ― Alarmoutmask2 60 Spanconfigurationerror ― Mask 2-1 062: AO 1 4-20 lmt ― Alarmoutmask2 62 Analogoutput14-20mAlimiterror ― Mask 2-1 063: AO 2 4-20 lmt ― Alarmoutmask2 63 Analogoutput24-20mAlimiterror ― Mask 2-1 064: AO 1 mlt rng ― Alarmoutmask2 64 Analogoutput1multirangeerror ― Mask 2-1 065:H/LcfgERR ― Alarmoutmask2 65 H/LHH/LLconfigurationerror ― Mask 2-1 066:DensitycfgERR ― Alarmoutmask2 66 Densityconfigurationerror ― Mask 2-2 067:Pls1cfgERR ― Alarmoutmask2 67 Pulseoutput1configurationerror ― Mask 2-2 068:Pls2cfgERR ― Alarmoutmask2 68 Pulseoutput2configurationerror ― Mask 2-2 069:Nomisizecfg ― Alarmoutmask2 69 Nominalsizeconfigurationerror ― Mask 2-2 070:AdhcfgERR ― Alarmoutmask2 70 Adhesionconfigurationerror ― Mask 2-2 071:FLNcfgERR ― Alarmoutmask2 71 Flownoiseconfigurationerror ― Mask 2-2 072: Log not start ― Alarmoutmask2 72 Data logging not started ― Mask 2-2 080:AO1saturate Alarmoutmask2 80 Analogoutput1saturated Mask 2-2 081:AO2saturate Alarmoutmask2 81 Analogoutput2saturated Mask 2-2 082:Pls1saturate Alarmoutmask2 82 Pulseoutput1saturated Mask 2-2 083:Pls2saturate Alarmoutmask2 83 Pulseoutput2saturated Mask 2-2 084:AIsaturate Alarmoutmask2 84 Analoginputsaturated Mask 2-2 085: Cable miscon ― Alarmoutmask2 85 Cable misconnect ― Mask 2-2 086:Coilinsulation Alarmoutmask2 86 Coilinsulationwarning Mask 2-2 131: Trans mismatch ― Alarmoutmask2 131 Transmitter type mismatch ― Mask 3-1 087: Adhesion lv 3 Alarmoutmask3 87 Adhesion over level 3 Mask 3-1 088: LC warn Alarmoutmask3 88 Lowconductivitywarning Mask 3-1 089:Insudetect Alarmoutmask3 89 Insulationdetection Mask 3-1 090: FLN over lv 3 Alarmoutmask3 90 Flow noise over level 3 Mask 3-1 091: FLN over lv 4 Alarmoutmask3 91 Flow noise over level 4 Mask 3-1 092: AZ warn Alarmoutmask3 92 Autozerowarning Mask 3-1 093:Verifwarn Alarmoutmask3 93 Verificationwarning Mask 3-1 094: Fact noise warn Alarmoutmask3 94 Factory noise warning Mask 3-1 095:Simulateactive ― Alarmoutmask3 95 Simulationactive ― Mask 3-1 096:AO1fix ― Alarmoutmask3 96 Analogoutput1fixed ― Mask 3-1 097:AO2fix ― Alarmoutmask3 97 Analogoutput2fixed ―
<4. Functions> 61
IM 01E22A02-02EN
Display HARTParameter
name Alarm name Default value Attribute Parameter name Alarm name Default
value Attribute
Mask 3-1 098:Pls1fix ― Alarmoutmask3 98 Pulseoutput1fixed ― Mask 3-1 099:Pls2fix ― Alarmoutmask3 99 Pulseoutput2fixed ― Mask 3-1 100:AIfix ― Alarmoutmask3 100 Analoginputfixed ― Mask 3-2 101:Paramrestorerun Alarmoutmask3 101 Parameterrestorerunning Mask 3-2 102: Disp over Alarmoutmask3 102 Display over warning Mask 3-2 103: SD size warn Alarmoutmask3 103 microSD card size warning Mask 3-2 104:Bkupincmplt Alarmoutmask3 104 Parameterbackupincomplete Mask 3-2 105: SD mismatch Alarmoutmask3 105 microSD card mismatch Mask 3-2 106: SD removal ERR Alarmoutmask3 106 microSDcardremovalprocedureerror Mask 3-2 120:Watchdog*1 Alarmoutmask3 120 Watchdog*1 Mask 3-2 121:Poweroff*1 Alarmoutmask3 121 Poweroff*1 Mask 3-2 122: Inst power FAIL*1 Alarmoutmask3 122 Instantpowerfailure*1 Mask 3-2 123:Parambkuprun Alarmoutmask3 123 Parameterbackuprunning Mask 3-2 124:Datalogrun Alarmoutmask3 124 Dataloggingrunning Mask 4-1 130:DevID not enter Alarmoutmask4 130 Device ID not entered
*1: Recordedinthealarmhistoryregardlessofthesettingofthealarmnotificationmaskfunction.
(2) Alarm history mask functionDisplay HART
Parameter name Alarm name Default
value Attribute Parameter name Alarm name Default value Attribute
― 010: Main CPU FAIL ― ― ― 10 MainboardCPUfailure ― ―― 011: Rev calc FAIL ― ― ― 11 Reversecalculationfailure ― ―― 012: Main EEP FAIL ― ― ― 12 MainboardEEPROMfailure ― ―
Mask 1-1 013:MainEEPdflt ― Alarm record mask 1 13 MainboardEEPROMdefault ― ― 014: Snsr bd FAIL ― ― ― 14 Sensorboardfailure ― ―― 015: Snsr comm ERR ― ― ― 15 Sensorcommunicationerror ― ―― 016: AD 1 FAIL[Sig] ― ― ― 16 A/D1failure[Signal] ― ―― 017: AD 2 FAIL[Excit] ― ― ― 17 A/D2failure[Exciter] ― ―― 018: Coil open ― ― ― 18 Coil open ― ―― 019: Coil short ― ― ― 19 Coil short ― ―
Mask 1-1 020: Exciter FAIL ― Alarm record mask 1 20 Exciterfailure ― Mask 1-2 021:PWM1stop ― Alarm record mask 1 21 PWM1stop ― Mask 1-2 022:PWM2stop ― Alarm record mask 1 22 PWM2stop ― Mask 1-2 023: Opt bd mismatch ― Alarm record mask 1 23 Option board mismatch ― Mask 1-2 024: Opt bd EEP FAIL ― Alarm record mask 1 24 OptionboardEEPROMfailure ― Mask 1-2 025:OptbdA/DFAIL ― Alarm record mask 1 25 OptionboardA/Dfailure ― Mask 1-2 026: Opt bd SPI FAIL ― Alarm record mask 1 26 OptionboardSPIfailure ―
― 027: Restore FAIL ― ― ― 27 Parameter restore incomplete ― ―Mask 1-2 028: Ind bd FAIL ― Alarm record mask 1 28 Indicatorboardfailure ― Mask 1-2 029: Ind bd EEP FAIL ― Alarm record mask 1 29 IndicatorboardEEPROMfailure ― Mask 1-2 030: LCD drv FAIL ― Alarm record mask 1 30 LCDdriverfailure ― Mask 1-2 031: Ind bd mismatch ― Alarm record mask 1 31 Indicator board mismatch ― Mask 1-2 032: Ind comm ERR ― Alarm record mask 1 32 Indicatorcommunicationerror ― Mask 1-2 033: microSD FAIL ― Alarm record mask 1 33 microSDfailure ― Mask 2-1 050:Signaloverflow ― Alarm record mask 2 50 Signaloverflow ― Mask 2-1 051: Empty detect ― Alarm record mask 2 51 Empty pipe detection ― Mask 2-1 052:H/LHH/LLalm ― Alarm record mask 2 52 H/LorHH/LLalarm ― Mask 2-1 053: Adh over lv 4 ― Alarm record mask 2 53 Adhesion over level 4 ―
― 060:SpancfgERR ― ― 60 Spanconfigurationerror ―― 062: AO 1 4-20 lmt ― ― 62 Analogoutput14-20mAlimiterror ―― 063: AO 2 4-20 lmt ― ― 63 Analogoutput24-20mAlimiterror ―― 064: AO 1 mlt rng ― ― 64 Analogoutput1multirangeerror ―― 065:H/LcfgERR ― ― 65 H/LHH/LLconfigurationerror ―― 066:DensitycfgERR ― ― 66 Densityconfigurationerror ―― 067:Pls1cfgERR ― ― 67 Pulseoutput1configurationerror ―― 068:Pls2cfgERR ― ― 68 Pulseoutput2configurationerror ―― 069:Nomisizecfg ― ― 69 Nominalsizeconfigurationerror ―― 070:AdhcfgERR ― ― 70 Adhesionconfigurationerror ―― 071:FLNcfgERR ― ― 71 Flownoiseconfigurationerror ―― 072: Log not start ― ― 72 Data logging not started ―― 080:AO1saturate ― ― 80 Analogoutput1saturated ―― 081:AO2saturate ― ― 81 Analogoutput2saturated ―― 082:Pls1saturate ― ― 82 Pulseoutput1saturated ―― 083:Pls2saturate ― ― 83 Pulseoutput2saturated ―― 084:AIsaturate ― ― 84 Analoginputsaturated ―
<4. Functions> 62
IM 01E22A02-02EN
Display HARTParameter
name Alarm name Default value Attribute Parameter name Alarm name Default
value Attribute
Mask 2-2 085: Cable miscon ― Alarm record mask 2 85 Cable misconnect ― ― 086:Coilinsulation ― ― 86 Coilinsulationwarning ―― 131: Trans mismatch ― ― 131 Transmitter type mismatch ―― 087: Adhesion lv 3 ― ― 87 Adhesion over level 3 ―― 088: LC warn ― ― 88 Lowconductivitywarning ―― 089:Insudetect ― ― 89 Insulationdetection ―― 090: FLN over lv 3 ― ― 90 Flow noise over level 3 ―― 091: FLN over lv 4 ― ― 91 Flow noise over level 4 ―― 092: AZ warn ― ― 92 Autozerowarning ―― 093:Verifwarn ― ― 93 Verificationwarning ―― 094: Fact noise warn ― ― 94 Factory noise warning ―― 095:Simulateactive ― ― 95 Simulationactive ―― 096:AO1fix ― ― 96 Analogoutput1fixed ―― 097:AO2fix ― ― 97 Analogoutput2fixed ―― 098:Pls1fix ― ― 98 Pulseoutput1fixed ―― 099:Pls2fix ― ― 99 Pulseoutput2fixed ―― 100:AIfix ― ― 100 Analoginputfixed ―― 101:Paramrestorerun ― ― 101 Parameterrestorerunning ―― 102: Disp over ― ― 102 Display over warning ―― 103: SD size warn ― ― 103 microSD card size warning ―― 104:Bkupincmplt ― ― 104 Parameterbackupincomplete ―― 105: SD mismatch ― ― 105 microSD card mismatch ―― 106: SD removal ERR ― ― 106 microSDcardremovalprocedureerror ―― 120:Watchdog*1 ― ― ― 120 Watchdog*1 ― ―― 121:Poweroff*1 ― ― ― 121 Poweroff*1 ― ―― 122: Inst power FAIL*1 ― ― ― 122 Instantpowerfailure*1 ― ―― 123:Parambkuprun ― ― 123 Parameterbackuprunning ―― 124:Datalogrun ― ― 124 Dataloggingrunning ―
Mask 3-1 130:DevID not enter Alarm record mask 3 130 Device ID not entered
*1: Recordedinthealarmhistoryregardlessofthesettingofthealarmnotificationmaskfunction.
<4. Functions> 63
IM 01E22A02-02EN
4.9 Display
4.9.1 Language SettingThelanguagetobeusedonthedisplaycanbeselectedfromninetypes.Selectthedesireddisplaylanguagefromthelanguagesthatareincludedinthelanguagepackagespecifiedatthetimeofordering.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Languageselection:Devicesetup►(seebelow)Language Specifythelanguagetobeusedonthe
display.*1
Displayoflanguagepackage:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Languagepackage Indicatesthelanguagepackageforthe
display.
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Language Specifythelanguagetobeusedonthe
display.*1
Languagepackage Indicatesthelanguagepackageforthedisplay.
Thefollowinglanguagesareincludedinthelanguagepackage.Package 1 Japanese,English,French,German,
Italian,Spanish,Portuguese,andRussian
Package 2 English and Chinese
*1: Fromthetablebelow,selectthelanguagetobeusedonthedisplay.
English Displays parameters in English.French Displays parameters in French.German Displays parameters in German.Italian Displays parameters in Italian.Spanish Displays parameters in Spanish.Portuguese DisplaysparametersinPortuguese.Russian DisplaysparametersinRussian.Chinese Displays parameters in Chinese.Japanese DisplaysparametersinJapanese.
4.9.2 Display Item SettingThisinstrumentcanbeshownuptoeightitemsonthedisplaywhilescrollingthescreen.Specifyadisplayitemineachofeightdisplaylines.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Lineselect►(seebelow)Line 1 Specifyitem1tobeshownonthedisplay.*1Line 2 Specifyitem2tobeshownonthedisplay.*1Line 3 Specifyitem3tobeshownonthedisplay.*1Line 4 Specifyitem4tobeshownonthedisplay.*1Line 5 Specifyitem5tobeshownonthedisplay.*1Line 6 Specifyitem6tobeshownonthedisplay.*1Line 7 Specifyitem7tobeshownonthedisplay.*1Line 8 Specifyitem8tobeshownonthedisplay.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Lineselect►(seebelow)Display select1 Specifyitem1tobeshownonthedisplay.*1Display select2 Specifyitem2tobeshownonthedisplay.*1Display select3 Specifyitem3tobeshownonthedisplay.*1Display select4 Specifyitem4tobeshownonthedisplay.*1Display select5 Specifyitem5tobeshownonthedisplay.*1Display select6 Specifyitem6tobeshownonthedisplay.*1Display select7 Specifyitem7tobeshownonthedisplay.*1Display select8 Specifyitem8tobeshownonthedisplay.*1
*1: From the table below, select the items to be shown on the display.
None Does not display items (item 1 is not selectable).
Flowrate(%) DisplaystheflowrateforthespanoftheprocessvaluethatisPV-mappedinSubsection4.1.2.
PV DisplaystheprocessvaluethatisPV-mappedinSubsection4.1.2.
Velocity Displaystheflowvelocity.Volumeflow Displaysthevolumetricflowrate.Massflow Displaysthemassflowrate.Flowrate(%Bar) Displaystheflowrateforthespanofthe
processvaluethatisPV-mappedinSubsection4.1.2,usingabargraph.
Calorie Displays the calorie.Totalizer 1 Displaysthetotalizedvalueoftotalizer1.Totalizer 2 Displaysthetotalizedvalueoftotalizer2.Totalizer 3 Displaysthetotalizedvalueoftotalizer3.Tagnumber Displaysthetagnumber.Long tag Displays the long tag.Communprotocol Displaysthecommunicationprotocol.Adhesion Displaystheadhesionleveloftheelectrode
adhesiondetectingfunction.Analogout1 Specifythecurrentvalueofcurrentoutput1for
theI/O1terminal.Analogout2 Specifythecurrentvalueofcurrentoutput2for
theI/O3orI/O4terminal.Flow noise Displaysthenoiseleveloftheflownoise
diagnosisfunction.
<4. Functions> 64
IM 01E22A02-02EN
4.9.3 Decimal-Point Position SettingThenumberofdecimalplacescanbesettotheautomaticadjustmentorfixmodeforthetotalizedvalueorprocessvaluePV-mappedinSubsection4.1.2.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Dispformat►(seebelow)Format PV Specifythedecimal-pointpositionfor
theprocessvaluethatisPV-mappedinSubsection4.1.2.*1
Format total 1 Specifythedecimal-pointpositionforthetotalizedvalueoftotalizer1.*1
Format total 2 Specifythedecimal-pointpositionforthetotalizedvalueoftotalizer2.*1
Format total 3 Specifythedecimal-pointpositionforthetotalizedvalueoftotalizer3.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayformat►(seebelow)DisplayformatPV Specifythedecimal-pointpositionfor
theprocessvaluethatisPV-mappedinSubsection4.1.2.*1
Displayformattotal1 Specifythedecimal-pointpositionforthetotalizedvalueoftotalizer1.*1
Displayformattotal2 Specifythedecimal-pointpositionforthetotalizedvalueoftotalizer2.*1
Displayformattotal3 Specifythedecimal-pointpositionforthetotalizedvalueoftotalizer3.*1
*1: Fromthetablebelow,selectthepositionofthedecimalpoint.Processvalue
Auto Automaticallyadjuststhenumberofdecimalplaces.0 digit Fixesthenumberofdecimalplacesto"0".1 digit Fixesthenumberofdecimalplacesto"1".2 digit Fixesthenumberofdecimalplacesto"2".3 digit Fixesthenumberofdecimalplacesto"3".4 digit Fixesthenumberofdecimalplacesto"4".5 digit Fixesthenumberofdecimalplacesto"5".
Totalizedvalue
Auto Automaticallyadjuststhenumberofdecimalplaces.0 digit Fixesthenumberofdecimalplacesto"0".0 digit Fixesthenumberofdecimalplacesto"1".2 digit Fixesthenumberofdecimalplacesto"2".3 digit Fixesthenumberofdecimalplacesto"3".4 digit Fixesthenumberofdecimalplacesto"4".5 digit Fixesthenumberofdecimalplacesto"5".6 digit Fixesthenumberofdecimalplacesto"6".7 digit Fixesthenumberofdecimalplacesto"7".
4.9.4 Display Line Count and Scroll Settings
Thisinstrumentcanbeshownuptofourlinesonthedisplaywhilescrollinguptoeightitems.Thescrollmethodcanbeselectedfromtheautomaticdisplayswitchingandthedisplayswitchingusingthe IR switch.Thesesettingscanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Line mode Specifythenumberoflinestobeshown
on the display.*1
Scroll mode Specifythedisplayscrollmethod.*2
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display line Specifythenumberoflinestobeshown
on the display.*1
Display scroll Specifythedisplayscrollmethod.*2
<4. Functions> 65
IM 01E22A02-02EN
*1: Fromthetablebelow,selectthenumberofdisplaylinesfromthe table below. Thefontsizeisautomaticallyadjusteddependingonthenumberofdisplaylines.
1 Line(Big) (1-line display without unit. The numeric value is displayed largely.)
F0427.ai
12345.678
01 : 00TL1
SET SFT INC
1 Line (1-line display with an unit)
F0428.ai
12345.6
01 : 00PRV
SET SFT INC
kg/h
2 Line (2-line display with units)
F0429.ai
12.34561.23456
01 : 00VFL
VEL
SET SFT INC
m/s
m3/h
3 Line (3-line display with units)
F0430.ai
12345.612345.678
01 : 00PRV
TL1TL2
SET SFT INC
kg12.345678m3
kg/h
4 Line (4-line display with units)
F0431.ai
12345.6
01 : 00MFL
PRV
CAL
TL1SET SFT INC
kg/h
kg/hkg
12345.612345.6
12345.678
MJ/h
*2: From the table below, select the scroll method.Off Does not scroll.Manual SetstothescrollusingtheIRswitch.Auto(2s) Setstotheautomaticscrollat2-secondintervals.Auto(4s) Setstotheautomaticscrollat4-secondintervals.Auto(8s) Setstotheautomaticscrollat8-secondintervals.
4.9.5 Trend Graph SettingThetrendgraphdisplayfunctiondisplaysatimechangeoftheselecteditemasatrendgraph.Uptofouritemscanbeshowninatrendgraph.Atrendgraphisscaledautomatically,andthetimeaxisflowsfromthelefttotheright.
01 : 00
SET SFT INC
01/01
F0432.ai
Process valueDisplay start time
Display end time
01:00
01/0101:01
PRV
(1) Trend graph display settingThetablebelowshowstheprocessvalues,lowlimitvalues,andhighlimitvaluesthatcanbeshowninatrend graph.
Process value Display Low limit
value High limit value
Flow rate (%)
FLP 0% 100%
PV PRV 0 SpanvaluespecifiedinSubsection4.1.5Flow velocity VEL
Volumetricflowrate
VFL
Massflowrate
MFL
Calorie CALCurrentoutput1
AO1 4 mA 20 mA
Currentoutput2
AO2
Totalization 1 TL1 PresetvaluespecifiedinSubsection4.2.7
TargetvalueofthetotalizerspecifiedinSubsection4.2.3
Totalization 2 TL2Totalization 3 TL3
Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Display mode Specifiesthedisplayofatrendgraph.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Displaymeasuremode
Specifiesthedisplayofatrendgraph.*1
*1: From the table below, select the trend graph display.Normal Does not display a trend graph (normal display).Trend Displays a trend graph.
NOTEThetrendgraphdisplayfunctionisnotsynchronizedwiththemultirangeandforward/reverserangefunctions.
<4. Functions> 66
IM 01E22A02-02EN
(2) Trend graph display item settingThissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Trendselect►(seebelow)Trend 1 Specifyitem1tobeshowninatrend
graph.*1
Trend 2 Specifyitem2tobeshowninatrendgraph. *1
Trend 3 Specifyitem3tobeshowninatrendgraph. *1
Trend 4 Specifyitem4tobeshowninatrendgraph. *1
HART communication:Devicerootmenu►Detailedsetup►Display► Trendselect►(seebelow)Trend select 1 Specifyitem1tobeshowninatrend
graph. *1
Trend select 2 Specifyitem2tobeshowninatrendgraph. *1
Trend select 3 Specifyitem3tobeshowninatrendgraph. *1
Trend select 4 Specifyitem4tobeshowninatrendgraph. *1
*1: Fromthetablebelow,selectthedisplayitemoftrendgraph.None Does not set any items (item 1 is not
selectable).Flowrate(%) Specifytheflowrateforthespanoftheprocess
valuethatisPV-mappedinSubsection4.1.2.PV SpecifytheprocessvaluethatisPV-mappedin
Subsection4.1.2.Velocity Specifytheflowvelocity.Volumeflow Specifythevolumetricflowrate.Massflow Specifythemassflowrate.Calorie Specifythecalorie.Analogout1 Specifythecurrentvalueofcurrentoutput1for
theI/O1terminal.Analogout2 Specifythecurrentvalueofcurrentoutput1for
theI/O3terminal.Totalizer1 Specifythetotalizedvalueoftotalizer1.Totalizer2 Specifythetotalizedvalueoftotalizer2.Totalizer3 Specifythetotalizedvalueoftotalizer3.
(3) Update period settingThissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Period Specifythetrendgraphupdateperiodon
the display.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display period Specifythetrendgraphupdateperiodon
the display.*1
*1: Fromthetablebelow,selectthetrendgraphupdateperiod.0.2s Setstheupdateperiodto0.2sec.0.4s Setstheupdateperiodto0.4sec.1.0s Setstheupdateperiodto1sec.2.0s Setstheupdateperiodto2sec.4.0s Setstheupdateperiodto4sec.8.0s Setstheupdateperiodto8sec.
4.9.6 Other Setting(1) Display contrast settingThedisplaycanbeadjustedthecontrastin11levels(+5to-5).Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Contrast Specifythecontrastofthedisplay.
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display contrast Specifythecontrastofthedisplay.
+5 +4 +3 +2 +1 0 -1 -2 -3 -4 -5High Low
(2) Display damping time constant settingThisfunctionenablestospecifythedampingtimeconstantforthedisplayindependentlyofthatspecifiedinSubsection4.1.6.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Damp Specifythedampingtimeconstantofthe
display.
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display damping Specifythedampingtimeconstantofthe
display.
NOTEThedampingtimeconstantofthedisplayisavailableonlyforthedisplay.Tospecifythedampingtimeconstantfortheoutputofthephysicalquantity,readSubsection4.1.6.
<4. Functions> 67
IM 01E22A02-02EN
(3) Date display format settingThedatedisplayformatcanbespecified.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Format date Specifythedatedisplayformat.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Displayformatdate Specifythedatedisplayformat.*1
*1:Fromthetablebelow,specifythedatedisplayformat.MM/DD/YYYY Displaysthedatein"month/day/year".DD/MM/YYYY Displaysthedatein"day/month/year".YYYY/MM/DD Displaysthedatein"year/month/day".
(4) Display black/white inverse settingTheblack/whiteinversefunctionisavailableforthedisplay.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Displayset►Optionalconfig►(seebelow)Inversion Specifythedisplayblack/whiteinverse
mode.*1
HART communication:Devicerootmenu►Detailedsetup►Display► Displayoperationconfiguration►(seebelow)Display inversion Specifythedisplayblack/whiteinverse
mode.*1
*1: Fromthetablebelow,selectthedisplayblack/whiteinversemode.
Normal Doesnotsetthedisplaytotheblack/whiteinverse mode.(Charactercolor:Black,Backgroundcolor:White)
Invert Setsthedisplaytotheblack/whiteinversemode.(Charactercolor:White,Backgroundcolor:Black)
(5) Display squawk settingThebacklightofthedisplaycanbesquawkedat4-secondintervalstoidentifythecommunicatinginstrumentwhereareinstalledanumberofsamemodels.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Dispindicator►(see below)Squawk Squawksthedisplay.*1
HART communication:Maintenancerootmenu►Displayindication►(see below)Squawk Squawksthedisplay.*1
*1:Fromthetablebelow,selectwhethertosquawkthedisplay.Off Doesnotsquawkthedisplay.On Squawksthedisplay(continuous).SquawkOnce Squawksthedisplay(onceonly).
<4. Functions> 68
IM 01E22A02-02EN
4.9.7 microSD Card SettingThededicatedmicroSDcardperformstousethebackupparametersandloggingdatabyinsertingintothedisplayiftheoptionalcodeMCisselected.Fordetailsaboutbackingupparametersandlogging data, read Section 4.13.
(1) Removing the microSD card
IMPORTANTIfthemicroSDcardisremovedwithoutexecuting“Unmount”onsoftware,itmaycausethestoreddata to be erased or the device to operate abnormally.
The microSD card can be removed with the followingparameters.
Display menu path:Devicesetup►microSD►(seebelow)Unmount SpecifiestheremovalofthemicroSD
card.*1
*1: From the table below, select whether to remove the microSD card.
Cancel CancelstheremovalofthemicroSDcard.Execute Applicable to remove the microSD card in
safety.
(2) microSD card format
IMPORTANTIftheformatfunctionofthisinstrumentisnotusedtoformatthemicroSDcard,itmaycauseadeviceoperationfailure.
Formattingispossiblewiththefollowingparameters.
Display menu path:Devicesetup►microSD►(seebelow)Format SpecifytheformatofthemicroSDcard.*1
*1: Fromthetablebelow,selectwhethertoformatthemicroSDcard.
Cancel Cancelsformatting.Execute Executesformatting.
4.10 Device Information
4.10.1 Order InformationOrderinformationcanbespecifiedforthisinstrument.Ifthededicatedparametersarespecifiedatthetimeofordering,thisinstrumentisshippedwiththeparametersconfigured.Parametersunspecifiedatthetimeoforderingmustbeconfiguredbytheuser.Themodelandsuffixcodeareindicatedinthefollowingformat.
Sensor:AXG - - / (1) (2) (3)
Transmitter:AXGA - / (1) (2) (3)
(1)Modelcode,(2)Suffixcode,(3)Optionalcode
Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Deviceinfo► Orderinfo►(seebelow)Tag No Specifythetagnumber.
HARTcommunication:Max.8characters.
Long tag Specifythelongtag.HARTcommunication:Max.32characters.
MScode►Modelcode
Specifythemodelcodeoftheintegralflowmeterorremotetransmitter.
MScode►Suffixconfig1
Specifythesuffixcodeoftheintegralflowmeterorremotetransmitter.
MScode►Suffixconfig2MScode►Option1 Specifytheoptionalcodeoftheintegral
flowmeterorremotetransmitter.MScode►Option2MScode►Option3MScode►Option4RSMScode►Modelcode
Specifythemodelcodeoftheremotesensor.
RSMScode►Suffixconfig1
Specifythesuffixcodeoftheremotesensor.
RSMScode►Suffixconfig2RS MS code►Option1
Specifytheoptionalcodeoftheremotesensor.
RS MS code►Option2RS MS code►Option3RS MS code►Option4
<4. Functions> 69
IM 01E22A02-02EN
Devicesetup►Detailedsetup►Deviceinfo► Ver/Numinfo►(seebelow)Trans serial No Displaystheserialnumber(instrument
number)ofthetransmitter.Sensor serial No Displaystheserialnumber(instrument
number)ofthesensor.
HART communication:Devicerootmenu►Detailedsetup► Deviceinformation►Orderinformation► (see below)Tag Specifythetagnumber.
HARTcommunication:Max.8characters.
Long tag Specifythelongtag.HARTcommunication:Max.32characters.
Basic model code Specifythemodelcodeoftheintegralflowmeterorremotetransmitter.
Suffixconfig1 Specifythesuffixcodeoftheintegralflowmeterorremotetransmitter.Suffixconfig2
Option 1 Specifytheoptionalcodeoftheintegralflowmeterorremotetransmitter.Option 2
Option 3Option 4Remote sensorbasic model code
Specifythemodelcodeoftheremotesensor.
Remote sensorsuffixconfig1
Specifythesuffixcodeoftheremotesensor.
Remote sensorsuffixconfig2Remote sensor option 1
Specifytheoptionalcodeoftheremotesensor.
Remote sensor option 2Remote sensor option 3Remote sensor option 4
Devicerootmenu►Detailedsetup► Deviceinformation► Version/Numberinformation►(seebelow)Transmitter serial No Displaystheserialnumber(instrument
number)ofthetransmitter.Sensor serial No Displaystheserialnumber(instrument
number)ofthesensor.
NOTEBecarefulofchanginganyparametersrelatedtoorderinformationdefineduponshipmentfromthemanufacturingplantbecauseitcannotbereferred.RecommendedtomakeabackupreferringtoSection4.13forstoringtheorderinformationdefineduponshipmentfromthemanufacturingplant.
4.10.2 Device RevisionThedevicerevisionsuchassoftwarewhichisusedforthisinstrumentcanbechecked.Thisinformationcanbeviewedwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Deviceinfo► Ver/Numinfo►(seebelow)Transmitter type Displaysthetypeofthetransmitter.Option board ID Displaysthetypeoftheoptionboard.Mainsoftrev Displaysthesoftwarerevisionofthemain
board.Snsrsoftrev Displaysthesoftwarerevisionofthe
sensor board.Indsoftrev Displaysthesoftwarerevisionofthe
display board.Hardwarerev Displaysthehardwarerevisionofthe
instrument.Dev id DisplaystheIDoftheinstrument.
HART communication:Devicerootmenu►Detailedsetup► Deviceinformation► Version/Numberinformation►(seebelow)Transmitter type Displaysthetypeofthetransmitter.Option board ID Displaysthetypeoftheoptionboard.Main board revision Displaysthesoftwarerevisionofthemain
board.Sensor board revision
Displaysthesoftwarerevisionofthesensor board.
Indicator board revision
Displaysthesoftwarerevisionofthedisplay board.
Hardwarerev Displaysthehardwarerevisionoftheinstrument.
Dev id DisplaystheIDoftheinstrument.
4.10.3 Memo FunctionThreeparameterscanbeusedasamemofunction.Thememofunctioncanbesettoupto16characters.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Detailedsetup►Deviceinfo►Memo►Memo 1 Specifiesmemo1.Memo 2 Specifiesmemo2.Memo 3 Specifiesmemo3.
HART communication:Devicerootmenu►Detailedsetup► Deviceinformation►Memo►(seebelow)Memo 1 Specifiesmemo1.Memo 2 Specifiesmemo2.Memo 3 Specifiesmemo3.
<4. Functions> 70
IM 01E22A02-02EN
4.11 Self-diagnostic Function
4.11.1 Types of Diagnosis FunctionsThisinstrumenthastheself-diagnosticfunctionstodiagnoseadevicefailureorprocessstatus.Followingsareitsdiagnosisfunctions.Alarmhigh/lowlimitfunction
Displaysanalarmwhenthespecifiedvalueisexceeded,andoutputsitasthestatusoutput.
Electrode adhesion detection
Diagnosesanelectrodeadhesionfromtheresistancevalueoftheelectrode,anddisplaysawarningoralarmifanadhesion is detected.
Sensor empty check Checks whether the sensor is in the emptypipestate,anddisplaysanalarmifthe empty pipe state is detected.
Misconnection detection
Checks whether the transmitter signal line and the excitation line are correctly connected,anddisplaysawarningifamisconnection is detected.
Verification(devicehealth diagnosis) function
Diagnosesthehealthoftheinstrument,anddisplaysitsresult.
Electrodeinsulationdeterioration diagnosis
Diagnosesadeteriorationofinsulationfromtheresistancevalueoftheelectrode,anddisplaysawarningifitisdetected.
Flow noise diagnosis Measuresaflownoisedetectedinthesensor,anddisplaysawarningifthemeasuredvalueexceedsthespecifiedvalue.
Lowconductivitydiagnosis
Obtainstheconductivityfromtheresistancevalueandsizeoftheelectrode,anddisplaysawarningiftheconductivityfallsbelowthespecifiedvalue.
4.11.2 Alarm High/Low Limit FunctionThealarmhigh/lowlimitfunctiondisplaysanalarmwhenthephysicalquantityPV-mappedinSubsection4.1.2exceedsthespecifiedvalue.Thisfunctionalsooutputsanalarmoccurrenceasthestatusoutput.Fordetailsaboutthestatusoutput,readSubsection4.3.7.Thealarmjudgmentvaluecanbespecifiedusing4typesofvalues:highlimitvalue,high-highlimitvalue,low-limitvalue,andlow-lowlimitvalue.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►H/Lalarmcfg►(see below)Highalarm Specifythehighlimitvaluetojudgean
alarm.Low alarm Specifythelowlimitvaluetojudgean
alarm.HHalarm Specifythehigh-highlimitvaluetojudge
an alarm.LL alarm Specifythelow-lowlimitvaluetojudge
an alarm.
HART communication:Maintenancerootmenu► High/Lowalarmconfiguration►(seebelow)Highalarm Specifythehighlimitvaluetojudgean
alarm.Low alarm Specifythelowlimitvaluetojudgean
alarm.Highhighalarm Specifythehigh-highlimitvaluetojudge
an alarm.Low low alarm Specifythelow-lowlimitvaluetojudge
an alarm.
Whenthehighandlowlimitvaluealarmsarereset,thehysteresisissetforeachalarm.Specifythehysteresiswidthwiththepercentage(%)forthespanofthephysicalquantityPV-mappedinSubsection4.1.2.Whenusingthemultirangefunction,specifythehysteresiswidthwiththepercentage(%)forthemaximumrangespecifiedinthemultirangeparameter.Thehysteresisineachcasecanbespecifiedbythefollowingprocedure.Fordetailsaboutthemultirangefunction,readSection 4.6.
Display menu path:Devicesetup►Diag/Service►H/Lalarmcfg►(see below)H/Lalarmhyst Specifythehysteresiswidthforthealarm
occurrenceandresetting.
HART communication:Maintenancerootmenu► High/Lowalarmconfiguration►(seebelow)Hi/Loalarmhysteresis Specifythehysteresiswidthforthe
alarmoccurrenceandresetting.
(1) Hysteresisvalue =Spanormax.rangexHysteresiswidth[%]
(2) Valuethatcausesahighlimitorhigh-highlimitalarm to be reset =Specifiedhighlimitorhigh-highlimitvalue-Hysteresisvalue
(3) Valuethatcausesalowlimitorlow-lowlimitalarm to be reset =Specifiedlowlimitorlow-lowlimitvalue+Hysteresisvalue
<4. Functions> 71
IM 01E22A02-02EN
Example:Spanofvolumetricflowrate=300m3/h,Highlimitvalue=250m3/h,Lowlimitvalue=50m3/h,High-highlimitvalue=300m3/h,Low-lowlimitvalue= 25 m3/h,Hysteresiswidth=5% Inthiscase,eachvalueisobtainedasshownbelow.
(1) Hysteresisvalue=300[m3/h]×5[%] = 15 [m3/h]
(2-1) Valuethatcausesahigh-highlimitalarmtobe reset = 300 [m3/h]–15[m3/h] = 285 [m3/h]
(2-2) Valuethatcausesahighlimitalarmtobereset = 250 [m3/h]–15[m3/h] = 235 [m3/h]
(3-1) Valuethatcausesalowlimitalarmtobereset = 50 [m3/h]+15[m3/h] = 65 [m3/h]
(3-2) Valuethatcausesalow-lowlimitalarmtobereset = 25 [m3/h]+15[m3/h] = 40 [m3/h]
F0433.ai
Time
Flow rate[m3/h]
300
250
5025
6540
285
235
Low LimitLow-Low Limit
High Limit
High-High Limit
Hysteresis
Status Output(High/Low limit)Status Output(High-High/Low-Low limit)
NOTEWhenthephysicalquantitytobeoutputischanged,respecifythealarmjudgmentvalue.
4.11.3 Electrode Adhesion DetectionTheelectrodeadhesiondetectingfunctiondiagnosesanelectrodeadhesionfromtheresistancevalueoftheelectrode,anddisplaysawarningoralarmifanadhesionisdetected.The electrode adhesion detection is displayed on thedisplayinfourlevels:level1tolevel4.Eachleveljudgmentvaluecanbespecifiedindividually.Ifthelevel3valueisexceeded,awarningisdisplayed.Ifthelevel4valueisexceeded,analarmis displayed.Fordetailsaboutalarmsandwarnings,readSubsection4.8.1.
F0434.ai
Alarm
Level 4
Warning
Level 3Level 2Level 1
Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►Adhesion►(seebelow)Function Specifiestheuseoftheelectrode
adhesiondetectingfunction.*1Threshold level 1 Specifythevaluetojudgelevel1.Threshold level 2 Specifythevaluetojudgelevel2.Threshold level 3 Specifythevaluetojudgelevel3.Threshold level 4 Specifythevaluetojudgelevel4.Result►Value Displaystheresistancevalueofthe
electrode.Result►Status Displays the electrode adhesion
detection level.Check cycle Specifythedataupdatecyclefor
electrode adhesion detection.
HART communication:Diagnosticrootmenu►Diagnosis► Adhesion►(seebelow)Adhesionfunction Specifiestheuseoftheelectrode
adhesiondetectingfunction.*1Adhesion level 1 Specifythevaluetojudgelevel1.Adhesion level 2 Specifythevaluetojudgelevel2.Adhesion level 3 Specifythevaluetojudgelevel3.Adhesion level 4 Specifythevaluetojudgelevel4.Result►Adhesionvalue
Displaystheresistancevalueoftheelectrode.
Result► Adhesionstatus
Displays the electrode adhesion detection level.
Adhesion check cycle
Specifythedataupdatecycleforelectrode adhesion detection.
*1: Fromthetablebelow,selecttheuseoftheelectrodeadhesiondetectionfunction.
Disable Doesnotusetheelectrodeadhesiondetectingfunction.
Enable Usestheelectrodeadhesiondetectingfunction.
<4. Functions> 72
IM 01E22A02-02EN
NOTEIftheelectrodeadhesiondetectingfunctionisnotused,theelectroderesistancevalueandlevelare cleared.
NOTEBeforeusingtheelectrodeadhesiondetectingfunction,alwaysmakesurethatthesensorisinthefullpipestate.Ifthesensorisintheemptypipestate,thisfunctionmaynotrunnormally.
NOTETheelectrodeadhesiondetectingfunctionhasthefluidconductivityrestricted.Therecommendedconductivityisasfollows.
Meter size Conductivity2.5 to 10 mm (0.1 to 0.4 in.) 30uS/cmorlarger15 to 400 mm (0.5 to 16 in.) 10uS/cmorlarger500 mm (20 in.) 20uS/cmorlarger
NOTEAsthedataupdatecycleforadhesiondetectionisshorter,anerroroftheelectroderesistancevalueincreases.Donotchangethedefaultvalueunlessespeciallyspecified.
4.11.4 Sensor Empty CheckThesensoremptycheckfunctioncheckswhetherthe sensor is in the empty pipe state, and displays analarmiftheemptypipestateisdetected.Fordetailsaboutalarmsandwarnings,readSubsection4.8.1.Thisinformationcanbeviewedwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►(see below)Emptystatus Displaystheresultofthesensorempty
checkfunction.*1
HART communication:Diagnosticrootmenu►Diagnosis►Empty► Result►(seebelow)Emptystatus Displaystheresultofthesensorempty
checkfunction.*1
*1: Fromthetablebelow,checktheresultofthesensoremptycheckfunction.
Full Indicates that the sensor is in the empty pipe state.
Empty Indicatesthatthesensorisinthefullpipestate.
4.11.5 Wiring Connection DiagnosisThewiringconnectiondiagnosticfunctionperformsto diagnose whether the signal line and the excitation line between remote type sensor and transmitter are correctly connected, and displays a warningifamisconnectionisdetected.Forexample,ifthereare2setsofremotetypesensorsandtransmitters,thisfunctionperformstocheckwhetherthesignallineofatransmitterAismisconnectedtothesignalterminalofasensorB,ortheexcitationlineofatransmitterAismisconnectedtotheexcitationterminalofasensorB.Ittakesapproximately10secondstofinishthisfunction.Fordetailsaboutalarmsandwarnings,readSubsection4.8.1.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►(see below)Diagnosticexecute Specifiestheuseofthewiringconnection
diagnosticfunction.*1Diagnosticoutput Specifiestheoutputtousethewiring
connectiondiagnosticfunction.*2
<4. Functions> 73
IM 01E22A02-02EN
HART communication:Diagnosticrootmenu►Diagnosis►(seebelow)Diagnostic Exe Specifiestheuseofthewiringconnection
diagnosticfunction.*1Diagnosticoutput Specifiestheoutputtousethewiring
connectiondiagnosticfunction.*2
*1: Fromthetablebelow,selecttheuseofthewiringconnectiondiagnosticfunction.
Connect check exe Starts the wiring connection diagnostic function.
*2: Fromthetablebelow,selecttheoutputrequiredtoexecutethewiringconnectiondiagnosticfunction.
Current output Totalization Pulse output Frequency
output
Zero 0%output Input0(Outputfixed) 0 pps 0%output
Measuredvalue
Outputofcalculatedvalue(Undefined)
Totalizationofcalculatedvalue(Undefined)
Outputofcalculatedvalue(Undefined)
Outputofcalculatedvalue(Undefined)
Hold
Fixes the last validvaluebeforethe
diagnosis starts.
Totalizes the lastvalidvaluebeforethe
diagnosis starts.
Fixes the last validvaluebeforethe
diagnosis starts.
Fixes the last validvaluebeforethe
diagnosis starts.
IMPORTANT• Beforeusingthewiringconnectiondiagnosticfunction,besuretodisconnectthisinstrumentfromthecontrolloop.
• Whilethisfunctionisused,thecurrentoutputandpulseoutputareinvalid.
NOTEWhenusingthewiringconnectiondiagnosticfunction,thefollowingconditionsmustbesatisfied.Iftheconditionsarenotsatisfied,themagneticflowmetermaynotcorrectlydiagnosethewiringconnectionstatus.• Thesensorisinthefullpipestate.• Noinfluenceofnoise.• Themagneticflowmetertransmitterand
AM012 (calibrator) are not connected.
4.11.6 Verification(DeviceHealthDiagnosis) Function
Theverificationfunctiondiagnosesthehealthoftheinstrument,anddisplaysthediagnosisresult.Ittakesapproximately15minutesfortheverificationfunctiontocomplete.Theprogressoftheverificationfunctioncanbemonitoredviathebar graph and the remaining time on the display.
F0435.ai
10:00
Verification executionExcitation circuit...
01 : 00
SET SFT INC
Thisfunctioncanperformtoinspecteachconditionofthecircuit,andactsthedevicehealthdiagnosisoftheinstrumentbydetectingitsinternalalarmshistory along with its wiring misconnection. And this functionevaluatestheirdiagnosisresultdependingontheconditionoftheinstrumentbyshowing“Passed”asnoproblemor“Failed”asproblemsonthe display.Theexecutingresultsareshownbelow.• “Passed” with no problem (as an example)VFcheckresults PassedVF Operation time 00001D 10:01Magneticcircuitresult PassedExcitingcircuitresult PassedCalculationcircuitresult PassedDevicestatusresult PassedConnectionstatusresult Passed
• “Failed” with problems (as an example)VFcheckresults FailedVF Operation time 00001D 10:01Magneticcircuitresult PassedExcitingcircuitresult PassedCalculationcircuitresult FailedDevicestatusresult PassedConnectionstatusresult Passed
<4. Functions> 74
IM 01E22A02-02EN
ContactYokogawaservicecenterwhenthe“Failed”massageappearsfrom“Magneticcircuitresult”to“Devicestatusresult”.Confirmthewiringmisconnectionbetweensensorandtransmitter(readSubsection4.11.5fordetail),or whether its signal cable and excitation cable havenodamagewhenthe“Failed”massageappearsat“Connectionstatusresult”.Theverificationfunctioncanbeselecteddependingonwhetherornotthefluidisflowing.Twodiagnosisresults(thistimeandtheprevioustime) can be stored on the device memory together withthedatadefineduponshipmentfromthemanufacturingplant,anditisabletocheckallofthemastheresult.Thefollowingresultswillbedisplayedaftertheverificationfunctionisused.Totaljudgmentresult CalculationcircuitdiagnosisresultOperatingtimeofverificationfunction
Devicealarmdiagnosisresult
Magneticcircuitdiagnosisresult
Wiringconnectiondiagnosisresult
Excitationcircuitdiagnosisresult
Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►(see below)Diagnosticoutput Specifiestheoutputtoexecutethe
verificationfunction.*1
Devicesetup►Diag/Service►Verification►(see below)Mode Specifiesthefluidstatustoexecutethe
verificationfunction.*2Execute Specifiestheexecutionoftheverification
function.*3VF No Specifythediagnosisresultdisplay
time.*4
Result Displaysthediagnosisresult.*5
HART communication:Maintenacerootmenu►Verification►(seebelow)Diagnosticoutput Specifiestheoutputtousethe
verificationfunction.*1VF mode Specifiesthefluidstatustousethe
verificationfunction.*2VerificationExe Specifiestheuseoftheverification
function.*3VF No Specifythediagnosisresultdisplay
time.*4
Result Displaysthediagnosisresult.*5
*1: Fromthetablebelow,selecttheoutputtoexecutetheverificationfunction.
Current output
Totalization Pulse output Frequency output
Zero 0%output Input0(Outputfixed) 0 pps 0%output
Measuredvalue
Outputofcalculatedvalue(Undefined)
Totalizationofcalculatedvalue(Undefined)
Outputofcalculatedvalue(Undefined)
Outputofcalculatedvalue(Undefined)
Hold
Fixes the last validvaluebeforethe
diagnosis starts.
Totalizes the lastvalidvaluebeforethe
diagnosis starts.
Fixes the last validvaluebeforethe
diagnosis starts.
Fixes the last validvaluebeforethe
diagnosis starts.
*2: Fromthetablebelow,selectthefluidstatusrequiredtoexecutetheverificationfunction.
Noflow Executestheverificationfunctionwiththefluidnotflowing.
Flow Executestheverificationfunctionwiththefluidflowing.
*3: Fromthetablebelow,selectwhethertoexecutetheverificationfunction.
Notexecute Doesnotexecutetheverificationfunction.Execute Executestheverificationfunction.
*4: Fromthetablebelow,selecttheexecutionresultoftheverificationfunction.
Factory Displaystheresultobtaineduponshipmentfromthemanufacturingplant.
Previous Displaysthepreviousresult.Present Displaystheresultatthistime.
*5: Thediagnosisresultisdisplayedasshownbelow.Display menu path:Devicesetup►Diag/Service►Result►(seebelow)
Failed/Passed ExecutionresultVF operate time Operatingtimeofverificationfunctionwhen
startedMagneticcircuit MagneticcircuitdiagnosisresultExcitecircuit ExcitationcircuitdiagnosisresultCalccircuit CalculationcircuitdiagnosisresultDevicestatus DevicealarmdiagnosisresultConnectstatus Wiringmisconnectioncheckresult
HART communication:Maintenacerootmenu►Verification►(seebelow)VFcheckresult ExecutionresultVF operation time Operatingtimeofverificationfunctionwhen
startedMagneticcircuitresult MagneticcircuitdiagnosisresultExcitationcircuitresult ExcitationcircuitdiagnosisresultCalculationcircuitresult CalculationcircuitdiagnosisresultVFdevicestatusresult DevicealarmdiagnosisresultConnectionstatusresult Wiringmisconnectioncheckresult
Thediagnosisresultisjudgedasshownbelow.
Passed There are no problems concerning the diagnosisresult.
Failed There is a problem concerning the diagnosis result.
Canceled Cancels the diagnosis.No Data Nodiagnosisresultdata
(Theverificationfunctionisnotused.)Unknown Cannotperformadiagnosis.
<4. Functions> 75
IM 01E22A02-02EN
IMPORTANT• Beforeusingtheverificationfunction,besuretodisconnectthisinstrumentfromthecontrolloop.
• Whilethisfunctionisused,thecurrentoutputandpulseoutputareinvalid.
• Note that parameters cannot be changed whentheverificationfunctionisexecuted.
NOTE• Beforeusingtheverificationfunction,alwaysmakesurethatthesensorisinthefullpipestate.Ifthesensorisintheemptypipestate,thisfunctionmaynotrunnormally.
• Whenusingtheverificationfunction,correctlyspecifythefluidstatuswiththeparameter.
• Ifthereisaproblemwiththeverificationresult,readthemaintenancemanualaslistedinTable 1.1.
4.11.7 Electrode Insulation Deterioration Diagnosis
Theelectrodeinsulationdeteriorationdiagnosisfunctiondiagnosesadeteriorationofinsulationfromtheresistancevalueoftheelectrode,anddisplaysawarningifitisdetected.Ittakesapproximately5minutestocompletethisdiagnosis.Fordetailsaboutalarmsandwarnings,readSubsection4.8.1.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►(see below)Diagnosticexecute Specifiestheexecutionoftheelectrode
insulationdeteriorationdiagnosisfunction.*1
Diagnosticoutput Specifiestheoutputtoexecutetheelectrodeinsulationdeteriorationdiagnosisfunction.*2
HART communication:Diagnosticrootmenu►Diagnosis►(seebelow)Diagnostic Exe Specifiestheexecutionoftheelectrode
insulationdeteriorationdiagnosisfunction.*1
Diagnosticoutput Specifiestheoutputtoexecutetheelectrodeinsulationdeteriorationdiagnosisfunction.*2
*1: Theelectrodeinsulationdeteriorationdiagnosiscanbeconfiguredwiththefollowingparameters.
Display:
Electrodeinsulexe Startstheelectrodeinsulationdeteriorationdiagnosisfunction.
HARTcommunication:
Electrodeinsulationexecute
Startstheelectrodeinsulationdeteriorationdiagnosisfunction.
*2: Fromthetablebelow,selecttheoutputrequiredtoexecutethediagnosisfunction.
Current output
Totalization Pulse output Frequency output
Zero 0%output Input0(Outputfixed) 0 pps 0%output
Measuredvalue
Outputofcalculatedvalue(Undefined)
Totalizationofcalculatedvalue(Undefined)
Outputofcalculatedvalue(Undefined)
Outputofcalculatedvalue(Undefined)
Hold
Fixes the last validvaluebeforethe
diagnosis starts.
Totalizes the lastvalidvaluebeforethe
diagnosis starts.
Fixes the last validvaluebeforethe
diagnosis starts.
Fixes the last validvaluebeforethe
diagnosis starts.
IMPORTANT• Beforeusingtheelectrodeinsulationdeteriorationdiagnosisfunction,besuretodisconnectthisinstrumentfromthecontrolloop.
• Whilethisfunctionisused,thecurrentoutputandpulseoutputareinvalid.
NOTEBeforeusingtheelectrodeinsulationdeteriorationdiagnosisfunction,alwaysmakesurethatthesensorisinthefullpipestate.Ifthesensorisintheemptypipestate,thisfunctionmaynotrunnormally.
<4. Functions> 76
IM 01E22A02-02EN
4.11.8 Flow Noise DiagnosisThisfunctionmeasuresaflownoisedetectedinthesensor,anddisplaysawarningifitexceedsthespecifiedvalue.Theflownoisediagnosisisshownonthedisplayinfourlevels:level1tolevel4.Eachleveljudgmentvaluecanbespecifiedindividually.Ifthelevel3orlevel4valueisexceeded,awarningmessageisappeared.Fordetailsaboutalarmsandwarnings,readSubsection4.8.1.Fordetailsabouttheflownoisespananddampingtimeconstant,readSubsection4.1.5and4.1.6.
F0436.ai
Warning
Level 4
Warning
Level 3Level 2Level 1
Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►Flownoise►(seebelow)Function Specifiestheuseoftheflownoise
diagnosisfunction.*1Threshold level 1 Specifythevaluetojudgelevel1.Threshold level 2 Specifythevaluetojudgelevel2.Threshold level 3 Specifythevaluetojudgelevel3.Threshold level 4 Specifythevaluetojudgelevel4.Result►Value Displaystheflownoisevalue.Result►Status Displaystheflownoiselevel.
HART communication:Diagnosticrootmenu►Diagnosis► Flownoise►(seebelow)Flownoisefunction Specifiestheuseoftheflownoise
diagnosisfunction.*1Flow noise level 1 Specifythevaluetojudgelevel1.Flow noise level 2 Specifythevaluetojudgelevel2.Flow noise level 3 Specifythevaluetojudgelevel3.Flow noise level 4 Specifythevaluetojudgelevel4.Result►Flownoise Displaystheflownoisevalue.Result► Flownoisestatus
Displaystheflownoiselevel.
*1: Fromthetablebelow,selecttheuseoftheflownoisefunction.Disable Doesnotusetheflownoisediagnosisfunction.Enable Usestheflownoisediagnosisfunction.
NOTEIftheflownoisediagnosisfunctionissetto“Disable”,theflownoisevalueandlevelarecleared.
4.11.9 Low Conductivity DiagnosisThelowconductivitydiagnosisfunctionobtainstheconductivityfromtheresistancevalueandsizeoftheelectrode,anddisplaysawarningiftheconductivityfallsbelowthespecifiedvalue.Fordetailsaboutalarmsandwarnings,readSubsection4.8.1.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Diagnosis►Conductivity►(seebelow)Function Specifiestheuseofthelowconductivity
diagnosisfunction.*1Result►Value Displaysthecalculatedconductivity.Low limit Specifythevalueusedtojudgethelow
conductivity.
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►(seebelow)Electrode size Displays the electrode size.
HART communication:Diagnosticrootmenu►Diagnosis► Conductivity►(seebelow)Lowconductivityfunction
Specifiestheuseofthelowconductivitydiagnosisfunction.*1
Result►Conductivityvalue
Displaysthecalculatedconductivity.
Conductivitylowlimit Specifythevalueusedtojudgethelowconductivity.
Devicerootmenu►Detailedsetup► Deviceinformation►Orderinformation► (see below)Electrode size Displays the electrode size.
*1: Fromthetablebelow,selecttheuseofthelowconductivitydiagnosisfunction.
Disable Doesnotusethelowconductivitydiagnosisfunction.
Enable Usesthelowconductivitydiagnosisfunction.
NOTETheelectrodesizeisspecifieduponshipmentfromthemanufacturingplant.Becarefulofchanginganyparametersrelatedtoorderinformationdefineduponshipmentfromthemanufacturingplantbecauseitcannotbereferred.RecommendedtomakeabackupreferringtoSection4.13forstoringtheorderinformationdefineduponshipmentfromthemanufacturingplant.
<4. Functions> 77
IM 01E22A02-02EN
NOTEBeforeusingthelowconductivitydiagnosisfunction,alwaysmakesurethatthesensorisinthefullpipestate.Ifthesensorisintheemptypipe state or the transmitter is connected with magneticflowmetercalibrator,thisfunctionmaynotrunnormally.
NOTE• Ifthisfunctionissetto“Disable”,thelowconductivityvalueiscleared.
4.12 Test Mode
4.12.1 Test Mode SettingThetestmodecanbeexecutedtoarbitrarilyspecifytheprocessvalueorthevaluetobeoutputfromaconnectionterminalandtestaresponsefromthedevice.However,awarningisdisplayedtoindicatethatthetestmodeisinusewhilethistestmodeisused.Theuseofthetestmodecanbespecifiedwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Test►(see below)Inputtest► Test mode
Specifiestheuseofthetestmode(input).*1
Outputtest► Test mode
Specifiestheuseofthetestmode(output).*1
HART communication:Maintenancerootmenu►Test►(seebelow)Test mode Specifiestheuseofthetestmode(input/
output).*1
*1: From the table below, select the test terminal and process value.
Display:
Velocity Startstestingtheflowvelocity.Volume Startstestingthevolumetricflowrate.Mass Startstestingthemassflowrate.Calorie Starts testing the calorie.AI StartstestingthecurrentinputoftheI/O4terminal.SI3 StartstestingthecurrentinputoftheI/O3terminal.AO1 Startstestingcurrentoutput1oftheI/O1terminal.AO2 Startstestingcurrentoutput2oftheI/O3orI/O4terminal.PO1 Startstestingpulseoutputorfrequencyoutput1ofthe
I/O2terminal.PO2 Startstestingpulseoutputorfrequencyoutput2ofthe
I/O3orI/O4terminal.SO1 Startstestingstatusoutput1oftheI/O2terminal.SO2 Startstestingcurrentoutput2oftheI/O3orI/O4terminal.SO3 Startstestingstatusoutput3oftheI/O3terminal.
HARTcommunication:Velocity test on Startstestingtheflowvelocity.Volumeflowteston Startstestingthevolumetricflowrate.Massflowteston Startstestingthemassflowrate.Calorificvalueteston Starts testing the calorie.AI test on StartstestingthecurrentinputoftheI/O4
terminal.SI3 test on StartstestingthecurrentinputoftheI/O3
terminal.AO1 test on Startstestingcurrentoutput1oftheI/O1
terminal.AO2 test on Startstestingcurrentoutput2oftheI/O3or
I/O4terminal.Pulse1teston Startstestingpulseoutputorfrequencyoutput
1oftheI/O2terminal.Pulse2teston Startstestingpulseoutputorfrequencyoutput
2oftheI/O3orI/O4terminal.SO1 test on Startstestingstatusoutput1oftheI/O2
terminal.SO2 test on Startstestingcurrentoutput2oftheI/O3or
I/O4terminal.SO3 test on Startstestingstatusoutput3oftheI/O3
terminal.
<4. Functions> 78
IM 01E22A02-02EN
ThevalueonthetestmodeisexecutedbyturnsofFlowvelocity,Volumetricflowrate,Massflowrate,andCalorie.Forexample,thetestvaluesofMassflowrateandCaloriearedecidedbasedonthetestvalueofthevolumetricflowrate,whenthevolumetricflowrateissetasthetestvalue.Inthiscase,thetestvalueofflowvelocityisexecutedwiththenormalmeasurementvalue.
NOTETospecifyeachterminaloutput,readSubsection4.3.1.Ifthespecifiedoutputisdifferentfromtheteststartingoutput,thetestmodecannotbeused.Forexample,iftheI/O2terminalisassignedtothefrequencyoutputtostartthestatusoutputtest, the test cannot be started.
4.12.2 Test Terminal and Value SettingSpecifythetestinputvaluefortheterminalandprocessvaluetobetested.Thissettingcanbeconfiguredwiththefollowingparameters.However,theunitoftheprocessvaluetobetestedconformstothatspecifiedinSubsection4.1.4.Iftheunitischanged,theprocessvaluetobetestedisalsochangedsynchronouslywiththechangedunit.
Display menu path:Devicesetup►Diag/Service►Test►(see below)Inputtest►Velocity Specifytheflowvelocity.Inputtest►Volume Specifythevolumetricflowrate.Inputtest►Mass Specifythemassflowrate.Inputtest►Calorie Specifythecalorie.Inputtest►AI Specifythecurrentvalueofthecurrent
inputfortheI/O4terminal.Inputtest►SI3 Specifythestatusofthestatusinputfor
theI/O3terminal.Outputtest►AO1 Specifythecurrentvalueofcurrent
output1fortheI/O1terminal.Outputtest►AO2 Specifythecurrentvalueofcurrent
output2fortheI/O3orI/O4terminal.Outputtest►PO1 Specifythefrequencyofpulseoutputor
frequencyoutput1fortheI/O2terminal.Outputtest►PO2 Specifythefrequencyofpulseoutputor
frequencyoutput2fortheI/O3orI/O4terminal.
Outputtest►SO1 Specifythestatusofstatusoutput1fortheI/O2terminal.
Outputtest►SO2 Specifythestatusofstatusoutput2oftheI/O3orI/O4terminal.
Outputtest►SO3 Specifythestatusofstatusoutput3fortheI/O3terminal.
HART communication:Maintenancerootmenu►Test►(seebelow)Inputtest►Velocity Specifytheflowvelocity.Inputtest► Volumeflow
Specifythevolumetricflowrate.
Inputtest►Massflow
Specifythemassflowrate.
Inputtest► Calorificvalue
Specifythecalorie.
Inputtest►AI SpecifythecurrentvalueofthecurrentinputfortheI/O4terminal.
Inputtest►SI3 SpecifythestatusofthestatusinputfortheI/O3terminal.
Outputtest►AO1 Specifythecurrentvalueofcurrentoutput1fortheI/O1terminal.
Outputtest►AO2 Specifythecurrentvalueofcurrentoutput2fortheI/O3orI/O4terminal.
Outputtest►Pulse1 Specifythefrequencyofpulseoutputorfrequencyoutput1fortheI/O2terminal.
Outputtest►Pulse2 Specifythefrequencyofpulseoutputorfrequencyoutput2fortheI/O3orI/O4terminal.
Outputtest►SO1 Specifythestatusofstatusoutput1fortheI/O2terminal.
Outputtest►SO2 Specifythestatusofstatusoutput2oftheI/O3orI/O4terminal.
Outputtest►SO3 Specifythestatusofstatusoutput3fortheI/O3terminal.
4.12.3 Test Mode Auto ResetIfthespecifiedtimelapseswithnoparameterschanged while the test mode is enabled, the test modeisresetautomatically.Whenanytestmodeparameter is changed, the test mode reset time is extended.Thissettingcanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Test►(see below)Release time Specifythetimetoautomaticallyreset
the test mode.*1
HART communication:Maintenancerootmenu►Test►(seebelow)Release time Specifythetimetoautomaticallyreset
the test mode.*1
*1: Fromthetablebelow,selectthetestmodeautoresettime.10 min Sets the reset time to 10 min.30 min Sets the reset time to 30 min.1 h Setstheresettimeto1hour.3 h Setstheresettimeto3hours.12 h Setstheresettimeto12hours.
<4. Functions> 79
IM 01E22A02-02EN
4.13 Event Management Function
4.13.1 Backup FunctionThebackupfunctionenablestobackupparametersettingsinthedisplaybuilt-inmemoryormicroSDcard (with the optional code MC selected). Restoratingbackupdatacanbeusedtoduplicateparameter settings to another device. The display built-inmemorycanstorebackupdataforthreetimesandthemicroSDdependsonavailablefreespace.Therearethreebackupmethodsavailable:backupfromthemainboardofthisinstrumenttothememoryonthedisplayboard,backupfromthemainboardoftheinstrumenttothemicroSDcard,andbackupfromthememoryonthedisplayboardtothemicroSDcard.Thefilename,backupname,anddatecanbespecifiedtousethebackupfunction.ThedatabackedupinthemicroSDcardisstoredinthe“YOKOGAWA”folderasa“.PAR”file.
Thebackupfunctioncanbeconfiguredwiththefollowingparameters.Fordetailsaboutthebackupparameters,readSubsection4.13.3.
Display menu path:Devicesetup►Diag/Service► Parambkup/restore►(seebelow)Fbackupname Displaysthebackupnamedefinedupon
shipmentfromthemanufacturingplant.Fbackupdate Displaysthebackupdateuponshipment
fromthemanufacturingplant.SDbackupname Specifythenameofthefiletobebacked
uptothemicroSDcard.Backupname1 Specifybackupname1.
Up to 16 charactersBackupdate1 Specifydate1.Backupname2 Specifybackupname2.
Up to 16 charactersBackupdate2 Specifydate2.Backupname3 Specifybackupname3.
Up to 16 charactersBackupdate3 Specifydate3.Backupexecute Specifiestheuseofthebackup
function.*1
HART communication:Maintenancerootmenu► Parambkup/restore►(seebelow)Factorybackupname
Displaysthebackupnamedefineduponshipmentfromthemanufacturingplant.
Factorybackupdate Displaysthebackupdateuponshipmentfromthemanufacturingplant.
SDbackupname SpecifythenameofthefiletobebackeduptothemicroSDcard.
Backupname1 Specifybackupname1.Up to 16 characters
Backupdate1 Specifydate1.Backupname2 Specifybackupname2.
Up to 16 charactersBackupdate2 Specifydate2.Backupname3 Specifybackupname3.
Up to 16 charactersBackupdate3 Specifydate3.BackupExe Specifiestheuseofthebackup
function.*1
*1: Fromthetablebelow,selecthowthebackupfunctionistobeused.
NotExecute Doesnotexecutethebackupfunction.Store Main to 1 Backsupparametersettingsfromthemain
boardtomemory1inthedisplaybuilt-inmemory.
Store Main to 2 Backsupparametersettingsfromthemainboardtomemory2inthedisplaybuilt-inmemory.
Store Main to 3 Backsupparametersettingsfromthemainboardtomemory3inthedisplaybuilt-inmemory.
Store Main to SD Backsupparametersettingsfromthemainboard to the microSD card.
Store EEP1 to SD Backsupparametersettingsfrommemory1inthedisplaybuilt-inmemorytothemicroSDcard.
Store EEP2 to SD Backsupparametersettingsfrommemory2inthedisplaybuilt-inmemorytothemicroSDcard.
Store EEP3 to SD Backsupparametersettingsfrommemory3inthedisplaybuilt-inmemorytothemicroSDcard.
There are some parameters which are not able to backupdependingontheoccurrenceofthealarm.The table below shows the parameters that can be backedupwhenanalarmoccurs.
:Executablewhenalarmoccurs.―:Notexecutablewhenalarmoccurs.
Alarm nameBackupDisplay HART
communication010:Main CPU FAIL 10 MainboardCPUfailure ―011:Rev calc FAIL 11 Reversecalculationfailure ―012:Main EEP FAIL 12 MainboardEEPROMfailure ―
013:MainEEPdflt 13 Main board EEPROM default ―
014:Snsr bd FAIL 14 Sensorboardfailure 015:Snsr comm ERR 15 Sensorcommunicationerror 016:AD 1 FAIL[Sig] 16 A/D1failure[Signal] 017:AD 2 FAIL[Excit] 17 A/D2failure[Exciter] 018:Coil open 18 Coil open 019:Coil short 19 Coil short 020:Exciter FAIL 20 Exciterfailure 021:PWM1stop 21 PWM1stop ―022:PWM2stop 22 PWM2stop ―023:Opt bd mismatch 23 Option board mismatch ―
<4. Functions> 80
IM 01E22A02-02EN
Alarm nameBackupDisplay HART
communication024:Opt bd EEP FAIL 24 Option board EEPROM
failure ―
025:OptbdA/DFAIL 25 OptionboardA/Dfailure ―026:Opt bd SPI FAIL 26 OptionboardSPIfailure ―
027:Restore FAIL 27 Parameter restore incomplete
028:Ind bd FAIL 28 Indicatorboardfailure ―
029:Ind bd EEP FAIL 29 Indicator board EEPROM failure ―
030:LCD drv FAIL 30 LCDdriverfailure ―031:Ind bd mismatch 31 Indicator board mismatch ―
032:Ind comm ERR 32 Indicatorcommunicationerror ―
033:microSD FAIL 33 microSDfailure ―050:Signaloverflow 50 Signaloverflow 051:Empty detect 51 Empty pipe detection 052:H/LHH/LLalm 52 H/LorHH/LLalarm 053:Adh over lv 4 53 Adhesion over level 4 060:SpancfgERR 60 Spanconfigurationerror ―
062:AO 1 4-20 lmt 62 Analogoutput14-20mAlimit error ―
063:AO 2 4-20 lmt 63 Analogoutput24-20mAlimit error ―
064:AO 1 mlt rng 64 Analogoutput1multirangeerror ―
065:H/LcfgERR 65 H/LHH/LLconfigurationerror ―
066:DensitycfgERR 66 Densityconfigurationerror ―
067:Pls1cfgERR 67 Pulseoutput1configurationerror ―
068:Pls2cfgERR 68 Pulseoutput2configurationerror ―
069:Nomisizecfg 69 Nominalsizeconfigurationerror ―
070:AdhcfgERR 70 Adhesionconfigurationerror ―
071:FLNcfgERR 71 Flownoiseconfigurationerror ―
072:Log not start 72 Data logging not started ―080:AO1saturate 80 Analogoutput1saturated 081:AO2saturate 81 Analogoutput2saturated 082:Pls1saturate 82 Pulseoutput1saturated 083:Pls2saturate 83 Pulseoutput2saturated 084:AIsaturate 84 Analoginputsaturated 085:Cable miscon 85 Cable misconnect 086:Coilinsulation 86 Coilinsulationwarning 087:Adhesion lv 3 87 Adhesion over level 3 088:LC warn 88 Lowconductivitywarning 089:Insudetect 89 Insulationdetection 090:FLN over lv 3 90 Flow noise over level 3 091:FLN over lv 4 91 Flow noise over level 4 092:AZ warn 92 Autozerowarning 093:Verifwarn 93 Verificationwarning 094:Fact noise warn 94 Factory noise warning 095:Simulateactive 95 Simulationactive 096:AO1fix 96 Analogoutput1fixed 097:AO2fix 97 Analogoutput2fixed 098:Pls1fix 98 Pulseoutput1fixed 099:Pls2fix 99 Pulseoutput2fixed 100:AIfix 100 Analoginputfixed 101:Paramrestorerun 101 Parameterrestorerunning ―102:Disp over 102 Display over warning ―103:SD size warn 103 microSD card size warning ―
104:Bkupincmplt 104 Parameterbackupincomplete
105:SD mismatch 105 microSD card mismatch ―
106:SD removal ERR 106 microSD card removal procedureerror ―
131:Trans mismatch 131 Transmitter type mismatch ―120:Watchdog 120 Watchdog 121:Poweroff 121 Poweroff
Alarm nameBackupDisplay HART
communication122:Inst power FAIL 122 Instantpowerfailure 123:Parambkuprun 123 Parameterbackuprunning ―124:Datalogrun 124 Dataloggingrunning 130:DevID not enter 130 Device ID not entered
IMPORTANT• Note that parameters cannot be changed whenthebackupfunctionisexecuted.Ittakes approximately 20 seconds to complete backupprocessing.
• TakecarenottoduplicatethefilenamewhenbackingupdatatothemicroSDcard.
• Notethat,ifthemicroSDcardrunsoutoffreespace,thesubsequentdatawillnotbestored.
NOTEThebackupnameanddatedonotaffectthebackupfunction.Usethisasthememocolumnwhenperformingthebackupfunction.
<4. Functions> 81
IM 01E22A02-02EN
4.13.2 Restore / Duplicate FunctionTherestorefunctioncanberestoreparametersettings,whicharebackedupinthedisplaybuilt-in memory or microSD card (with the optional codeMCselected),totheinstrument.Inaddition,thisfunctionenablestoreturnparameterstothedefaultvaluesdefineduponshipmentfromthemanufacturingplant.Also,itispossibletoduplicatethebacked-upparameterstootherdevicebasedonthesamespecifications.
IMPORTANTFor the remote type, It is necessary to set the deviceinformationofremotesensorintotheparametersofremotetransmitter.
Therestoremethodcanbeselectedfromthefollowingfourtypes.DuplicateData Restoresthetargetparameter(excludingthe
service parameters related to the transmitter adjustment)fromtheinstrumentinwhichtheparameterisbackedup.Restoreisalsoexecutableforotherinstrument.
Restore Data Restoresthetargetparameter(includingtheservice parameters related to the transmitter adjustment)fromtheinstrumentinwhichtheparameterisbackedup.Restoreisnotexecutableforotherinstrument.
CompulsionData Restoresthetargetparameter(specifieduponshipmentfromthemanufacturingplant)fromtheinstrumentinwhichtheparameterisbackedup.Restoreisalsoexecutableforotherinstrument.
Restore Factory Restoresalltheparameters(specifieduponshipmentfromthemanufacturingplant).
Whenusingtherestorefunction,alwaysmakesurethatthebacked-updeviceinformationmatchesthedeviceinformationtoberestored.Thetablebelowshowstheconsistencyofdeviceinformation.
M:Items to be Matched.
Device Information Duplicate Data
Restore Data
Compulsion Data
Option Board ID M MTransmitter Serial No MSensor Serial No MMainBoardSoftwareRev. M MSensorBoardSoftwareRev. M MDisplayBoardSoftwareRev. M M
Model (Note) M MCommunicationandI/OCode M M
Note: OnlybetweenAXGtypeandAXGtypecanbeduplicatedor restored the data.
Therestorefunctioncanbeconfiguredwiththefollowingparameters.Fordetailsabouttherestorableparameters,readSubsection4.13.3.
Display menu path:Devicesetup►Diag/Service► Parambkup/restore►(seebelow)Restoreexecute Specifiestheexecutionoftherestore
function.*1Restoreresult Displaystherestoreresult.*2
HART communication:Maintenancerootmenu► Parambkup/restore►(seebelow)Restore Exe Specifiestheexecutionoftherestore
function.*1Displaystherestoreresultafterexecutionoftherestorefunction.*2
*1: Fromthetablebelow,selecttheexecutionoftherestorefunction.
Notexecute Does not restore data.DuplicateData1 Restorestheparameter(DuplicateData)
settingfrommemory1onthedisplayboardtothemainboardoftheinstrument.
DuplicateData2 Restorestheparameter(DuplicateData)settingfrommemory2onthedisplayboardtothemainboardoftheinstrument.
DuplicateData3 Restorestheparameter(DuplicateData)settingfrommemory3onthedisplayboardtothemainboardoftheinstrument.
DuplicateSD Restorestheparameter(DuplicateData)settingfromthemicroSDcardtothemainboardoftheinstrument.
Restore Data1 Restores the parameter (Restore Data) setting frommemory1onthedisplayboardtothemainboardoftheinstrument.
Restore Data2 Restores the parameter (Restore Data) setting frommemory2onthedisplayboardtothemainboardoftheinstrument.
Restore Data3 Restores the parameter (Restore Data) setting frommemory3onthedisplayboardtothemainboardoftheinstrument.
Restore SD Restores the parameter (Restore Data) setting fromthemicroSDcardtothemainboardoftheinstrument.
CompulsionData1 Restorestheparameter(CompulsionData)settingfrommemory1onthedisplayboardtothemainboardoftheinstrument.
CompulsionData2 Restorestheparameter(CompulsionData)settingfrommemory2onthedisplayboardtothemainboardoftheinstrument.
CompulsionData3 Restorestheparameter(CompulsionData)settingfrommemory3onthedisplayboardtothemainboardoftheinstrument.
CompulsionSD Restorestheparameter(CompulsionData)settingfromthemicroSDcardtothemainboardoftheinstrument.
Restore Factory Restorestothestatusthatissetuponshipmentfromthemanufacturingplant.
*2: Theresultoftherestorefunctionisdisplayedasshownbelow.Unexecuted Does not restore data.Success Succeededinrestoration.Failure Failed in restoration.Running Parameterrestorerunning
<4. Functions> 82
IM 01E22A02-02EN
There are some parameters which are not able to backupdependingontheoccurrenceofthealarm.The table below shows the parameters that can be backedupwhenanalarmoccurs.
:Executablewhenalarmoccurs.―:Notexecutablewhenalarmoccurs.
Alarm nameRestoreDisplay HART
communication010:Main CPU FAIL 10 MainboardCPUfailure ―011:Rev calc FAIL 11 Reversecalculationfailure ―012:Main EEP FAIL 12 MainboardEEPROMfailure ―
013:MainEEPdflt 13 Main board EEPROM default ―
014:Snsr bd FAIL 14 Sensorboardfailure 015:Snsr comm ERR 15 Sensorcommunicationerror 016:AD 1 FAIL[Sig] 16 A/D1failure[Signal] 017:AD 2 FAIL[Excit] 17 A/D2failure[Exciter] 018:Coil open 18 Coil open 019:Coil short 19 Coil short 020:Exciter FAIL 20 Exciterfailure 021:PWM1stop 21 PWM1stop ―022:PWM2stop 22 PWM2stop ―023:Opt bd mismatch 23 Option board mismatch ―
024:Opt bd EEP FAIL 24 Option board EEPROM failure ―
025:OptbdA/DFAIL 25 OptionboardA/Dfailure ―026:Opt bd SPI FAIL 26 OptionboardSPIfailure ―
027:Restore FAIL 27 Parameter restore incomplete
028:Ind bd FAIL 28 Indicatorboardfailure ―
029:Ind bd EEP FAIL 29 Indicator board EEPROM failure ―
030:LCD drv FAIL 30 LCDdriverfailure ―031:Ind bd mismatch 31 Indicator board mismatch ―
032:Ind comm ERR 32 Indicatorcommunicationerror ―
033:microSD FAIL 33 microSDfailure ―050:Signaloverflow 50 Signaloverflow 051:Empty detect 51 Empty pipe detection 052:H/LHH/LLalm 52 H/LorHH/LLalarm 053:Adh over lv 4 53 Adhesion over level 4 060:SpancfgERR 60 Spanconfigurationerror ―
062:AO 1 4-20 lmt 62 Analogoutput14-20mAlimit error ―
063:AO 2 4-20 lmt 63 Analogoutput24-20mAlimit error ―
064:AO 1 mlt rng 64 Analogoutput1multirangeerror ―
065:H/LcfgERR 65 H/LHH/LLconfigurationerror ―
066:DensitycfgERR 66 Densityconfigurationerror ―
067:Pls1cfgERR 67 Pulseoutput1configurationerror ―
068:Pls2cfgERR 68 Pulseoutput2configurationerror ―
069:Nomisizecfg 69 Nominalsizeconfigurationerror ―
070:AdhcfgERR 70 Adhesionconfigurationerror ―
071:FLNcfgERR 71 Flownoiseconfigurationerror ―
072:Log not start 72 Data logging not started ―080:AO1saturate 80 Analogoutput1saturated 081:AO2saturate 81 Analogoutput2saturated 082:Pls1saturate 82 Pulseoutput1saturated 083:Pls2saturate 83 Pulseoutput2saturated 084:AIsaturate 84 Analoginputsaturated 085:Cable miscon 85 Cable misconnect 086:Coilinsulation 86 Coilinsulationwarning 087:Adhesion lv 3 87 Adhesion over level 3 088:LC warn 88 Lowconductivitywarning
Alarm nameRestoreDisplay HART
communication089:Insudetect 89 Insulationdetection 090:FLN over lv 3 90 Flow noise over level 3 091:FLN over lv 4 91 Flow noise over level 4 092:AZ warn 92 Autozerowarning 093:Verifwarn 93 Verificationwarning 094:Fact noise warn 94 Factory noise warning 095:Simulateactive 95 Simulationactive 096:AO1fix 96 Analogoutput1fixed 097:AO2fix 97 Analogoutput2fixed 098:Pls1fix 98 Pulseoutput1fixed 099:Pls2fix 99 Pulseoutput2fixed 100:AIfix 100 Analoginputfixed 101:Paramrestorerun 101 Parameterrestorerunning ―102:Disp over 102 Display over warning ―103:SD size warn 103 microSD card size warning ―
104:Bkupincmplt 104 Parameterbackupincomplete
105:SD mismatch 105 microSD card mismatch ―
106:SD removal ERR 106 microSD card removal procedureerror ―
131:Trans mismatch 131 Transmitter type mismatch ―120:Watchdog 120 Watchdog 121:Poweroff 121 Poweroff 122:Inst power FAIL 122 Instantpowerfailure 123:Parambkuprun 123 Parameterbackuprunning ―124:Datalogrun 124 Dataloggingrunning 130:DevID not enter 130 Device ID not entered
IMPORTANTWhenusingtherestorefunction,besuretopreparethebackupfileinmemoryoramicroSDcard.Notethattherestorefunctionisnotexecutableifthebackupfileisnotprovided.
<4. Functions> 83
IM 01E22A02-02EN
4.13.3 Backup and Restore ParametersThelistbelowshowstheparametersthatcanbebackeduporrestored.
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Process variables ► Velocity ► VelocitydampingAO/frequency
Devicesetup►Detailedsetup►Provar►Velocity►DampAO/F ―
Devicerootmenu► Detailedsetup► Process variables ► Velocity ► Velocitydampingpulse/total
Devicesetup►Detailedsetup►Provar►Velocity►Damppls/ttl ―
Devicerootmenu► Detailedsetup► Process variables ► Volumeflow► VolumeflowdampingAO/frequency
Devicesetup►Detailedsetup►Provar►Volume►DampAO/F ―
Devicerootmenu► Detailedsetup► Process variables ► Volumeflow► Volumeflowdampingpulse/total
Devicesetup►Detailedsetup►Provar►Volume►Damppls/ttl ―
Devicerootmenu► Detailedsetup► Process variables ► Massflow► MassflowdampingAO/frequency
Devicesetup►Detailedsetup►Provar►Mass►DampAO/F ―
Devicerootmenu► Detailedsetup► Process variables ► Massflow► Massflowdampingpulse/total
Devicesetup►Detailedsetup►Provar►Mass►Damppls/ttl ―
Devicerootmenu► Detailedsetup► Process variables ► Calorie ► CalorificvaluedampingAO/frequency
Devicesetup►Detailedsetup►Provar►Calorie►DampAO/F ―
Devicerootmenu► Detailedsetup► Process variables ► Calorie ► Calorificvaluedampingpulse/total
Devicesetup►Detailedsetup►Provar►Calorie►Damppls/ttl ―
Devicerootmenu► Detailedsetup► Sensor ► Low MF
Devicesetup►Detailedsetup►Sensor►Low MF
Devicerootmenu► Detailedsetup► Sensor ► HighMF
Devicesetup►Detailedsetup►Sensor►HighMF
Devicerootmenu► Detailedsetup► Sensor ► Flow sensor select
Devicesetup►Detailedsetup►Sensor►Flow sensor sel ―
Devicerootmenu► Detailedsetup► Sensor ► Nominalsizeunit
Devicesetup►Detailedsetup►Sensor►Nominalsizeunit
Devicerootmenu► Detailedsetup► Sensor ► Nominal size
Devicesetup►Detailedsetup►Sensor►Nominal size
Devicerootmenu► Detailedsetup► Process variables ► PVflowselect
Devicesetup►Detailedsetup►Provar►PVflowselect
Devicerootmenu► Detailedsetup► Process variables ► Velocity ►Velocityunit
Devicesetup►Detailedsetup►Provar►Velocity►Unit ― ―
<4. Functions> 84
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Process variables ► Volumeflow►Volumeflowunit
Devicesetup►Detailedsetup►Provar►Volume►Unit ― ―
Devicerootmenu► Detailedsetup► Process variables ► Massflow►Massflowunit
Devicesetup►Detailedsetup►Provar►Mass►Unit ― ―
Devicerootmenu► Detailedsetup► Process variables ► Volumeflow►Timeunit or Devicerootmenu► Detailedsetup► Process variables ► Massflow►TimeunitorDevicerootmenu►Detailedsetup► Process variables ► Calorie ► Timeunit
Devicesetup►Detailedsetup►Provar►Volume►Timeunit or Devicesetup►Detailedsetup►Provar►Mass►TimeunitorDevicesetup►Detailedsetup►Provar►Calorie►Timeunit
― ―
Devicerootmenu► Detailedsetup► Process variables ► Velocity ► Velocity span
Devicesetup►Detailedsetup►Provar►Velocity►Span
Devicerootmenu► Detailedsetup► Process variables ► Volumeflow►Volumeflowspan
Devicesetup►Detailedsetup►Provar►Volume►Span
Devicerootmenu► Detailedsetup► Process variables ► Massflow►Massflowspan
Devicesetup►Detailedsetup►Provar►Mass►Span
Devicerootmenu► Detailedsetup► Process variables ► Calorie ►Calorificflowspan
Devicesetup►Detailedsetup►Provar►Calorie►Span
Maintenancerootmenu► Autozero►Result►Zerovalue
Devicesetup►Diag/Service►Autozero►Result►Zerovalue ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ►Total1convfactor
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Convfactor ― ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ►Total1lowcut
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Lowcut ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ►Total1failopts
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Failureopts ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ► Total1 options
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Options ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ►Total1Start/Stop
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Start/Stop ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ►Total1Reset/Preset
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Reset/Preset ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ►Total1presetvalue
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Presetvalue ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer1 ► Total1 set point
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Setpoint ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ►Total2lowcut
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Lowcut ―
<4. Functions> 85
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ►Total2failopts
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Failureopts ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ► Total2 options
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Options ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ►Total2Start/Stop
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Start/Stop ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ►Total2Reset/Preset
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Reset/Preset ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ►Total2presetvalue
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Presetvalue ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer2 ► Total2 set point
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Setpoint ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ►Total3lowcut
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Lowcut ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ►Total3failopts
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Failureopts ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ► Total3 options
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Options ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ►Total3Start/Stop
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Start/Stop ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ►Total3Reset/Preset
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Reset/Preset ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ►Total3presetvalue
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Presetvalue ―
Devicerootmenu► Detailedsetup► Totalizer ► Totalizer3 ► Total3 set point
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Setpoint ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1outputmode
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Outputmode
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1activemode
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Activemode ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1fixwidth
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Fixwidth ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1rateunit
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Rateunit ― ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1ratevalue
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Ratevalue
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1lowcut
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Lowcut ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Pulse1alarmout
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Alarmout ―
<4. Functions> 86
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Frequency1at0%
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►Frequencyat0%
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Frequency1at100%
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1► Frequencyat100%
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput1► Statusoutput1function
Devicesetup►Detailedsetup► Pulse/Statusout►PO1/SO1►SO1function ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2activepulse
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Activepulse ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2outputmode
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Outputmode ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2select
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Pulseselect ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2activemode
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Activemode ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2fixwidth
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Fixwidth ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2ratevalue
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Ratevalue ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2lowcut
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Lowcut ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Pulse2alarmout
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Alarmout ―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Frequency2at0%
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►Frequencyat0%
―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Frequency2at100%
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2► Frequencyat100%
―
Devicerootmenu► Detailedsetup►Pulse/Status► Pulse/Statusoutput2► Statusoutput2function
Devicesetup►Detailedsetup► Pulse/Statusout►PO2/SO2►SO2function ―
Devicerootmenu► Detailedsetup►Pulse/Status► Statusoutput3► Statusoutput3activemode
Devicesetup►Detailedsetup► Pulse/Statusout►SO3►Activemode ―
Devicerootmenu► Detailedsetup►Pulse/Status► Statusoutput3► Statusoutput3function
Devicesetup►Detailedsetup► Pulse/Statusout►SO3►Function ―
<4. Functions> 87
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup►Pulse/Status► Statusinput3► Statusinput3activemode
Devicesetup►Detailedsetup►Statusin►SI3►Activemode ―
Devicerootmenu► Detailedsetup►Pulse/Status► Statusinput3► Statusinput3function
Devicesetup►Detailedsetup►Statusin►SI3►Function ―
Devicerootmenu► Detailedsetup►Multirange► Forward span 2
Devicesetup►Detailedsetup► Multirange►Forwardspan2 ―
Devicerootmenu► Detailedsetup►Multirange► Reverse span 1
Devicesetup►Detailedsetup► Multirange►Reversespan1 ―
Devicerootmenu► Detailedsetup►Multirange► Reverse span 2
Devicesetup►Detailedsetup► Multirange►Reversespan2 ―
Devicerootmenu► Detailedsetup►Multirange► Autorangehyst
Devicesetup►Detailedsetup► Multirange►Autorangehyst ―
Devicerootmenu► Detailedsetup►Multirange► Bi direction hyst
Devicesetup►Detailedsetup► Multirange►Bidirectionhyst ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput1►AO1lowcut
Devicesetup►Detailedsetup► Analogout/in►AO1►Lowcut ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput1► AO1 high limit
Devicesetup►Detailedsetup► Analogout/in►AO1►Highlimit ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput1► AO1 low limit
Devicesetup►Detailedsetup► Analogout/in►AO1►Lowlimit ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput1►AO1alarmout
Devicesetup►Detailedsetup► Analogout/in►AO1►Alarmout
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput1► AO1 range mode
Devicesetup►Detailedsetup► Analogout/in►AO1►Rangemode ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput2► AO2 select
Devicesetup►Detailedsetup► Analogout/in►AO2►AO2select ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput2►AO2lowcut
Devicesetup►Detailedsetup► Analogout/in►AO2►Lowcut ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput2► AO2 high limit
Devicesetup►Detailedsetup► Analogout/in►AO2►Highlimit ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput2► AO2 low limit
Devicesetup►Detailedsetup► Analogout/in►AO2►Lowlimit ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analogoutput2►AO2alarmout
Devicesetup►Detailedsetup► Analogout/in►AO2►Alarmout ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analoginput►AIfunction
Devicesetup►Detailedsetup► Analogout/in►AI►Function ―
<4. Functions> 88
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Analogoutput/input► Analoginput► AI URV
Devicesetup►Detailedsetup► Analogout/in►AI►URV ―
Devicerootmenu► Detailedsetup► Analogoutput/input► Analoginput► AI LRV
Devicesetup►Detailedsetup► Analogout/in►AI►LRV ―
Maintenancerootmenu► AO/AItrim► AO trim ► AO1 Trim
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO1trim4mA ―
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO1trim20mA ―
Maintenancerootmenu► AO/AItrim► AO trim ► AO2 Trim
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO2trim4mA ―
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO2trim20mA ―
Devicerootmenu► Detailedsetup► AUXcalculation► Flow direction
Devicesetup►Detailedsetup► AUXcalculation►Flowdirect ―
Devicerootmenu► Detailedsetup► AUXcalculation► Rate limit
Devicesetup►Detailedsetup► AUXcalculation►Ratelimit ―
Devicerootmenu► Detailedsetup► AUXcalculation► Dead time
Devicesetup►Detailedsetup► AUXcalculation►Deadtime ―
Devicerootmenu► Detailedsetup► AUXcalculation► Noisefilter
Devicesetup►Detailedsetup► AUXcalculation►Noisefilter ―
Devicerootmenu► Detailedsetup► AUXcalculation► Pulsingflow
Devicesetup►Detailedsetup► AUXcalculation►Pulsingflow ―
Devicerootmenu► Detailedsetup► AUXcalculation► Power synchronize
Devicesetup►Detailedsetup► AUXcalculation►Powersyncon/off
Devicerootmenu► Detailedsetup► AUXcalculation► Setpowerfrequency
Devicesetup►Detailedsetup► AUXcalculation►Setpowerfreq
Devicerootmenu► Detailedsetup► Process variables ► Density ►Densityvalueselect
Devicesetup►Detailedsetup►Provar►Density►Valueselect ―
Devicerootmenu► Detailedsetup► Process variables ► Density ►Densityfixedvalue
Devicesetup►Detailedsetup►Provar►Density►Fixeddensity
Devicerootmenu► Detailedsetup► Process variables ► Density ► Standard density
Devicesetup►Detailedsetup►Provar►Density►Stddensity ―
Devicerootmenu► Detailedsetup► Process variables ► Temperature► Standardtemperature
Devicesetup►Detailedsetup►Provar►Temperature►Stdtemperature ―
Devicerootmenu► Detailedsetup► Process variables ► Temperature►TempcoefA1
Devicesetup►Detailedsetup►Provar►Temperature►CoefA1 ―
<4. Functions> 89
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Process variables ► Temperature►TempcoefA2
Devicesetup►Detailedsetup►Provar►Temperature►CoefA2 ―
Devicerootmenu► Detailedsetup► Process variables ► Calorie ►Specificheat
Devicesetup►Detailedsetup►Provar►Calorie►Specificheat ―
Devicerootmenu► Detailedsetup► Process variables ► Temperature►Calorificfixtemp
Devicesetup►Detailedsetup►Provar►Temperature►Fixedtemperature ―
Maintenancerootmenu► High/Lowalarmconfiguration► Highalarm
Devicesetup►Diag/Service► H/Lalarmcfg►Highalarm ―
Maintenancerootmenu► High/Lowalarmconfiguration► Low alarm
Devicesetup►Diag/Service► H/Lalarmcfg►Lowalarm ―
Maintenancerootmenu► High/Lowalarmconfiguration► Highhighalarm
Devicesetup►Diag/Service► H/Lalarmcfg►HHalarm ―
Maintenancerootmenu► High/Lowalarmconfiguration► Low low alarm
Devicesetup►Diag/Service► H/Lalarmcfg►LLalarm ―
Maintenancerootmenu► High/Lowalarmconfiguration► Hi/Loalarmhysteresis
Devicesetup►Diag/Service► H/Lalarmcfg►H/Lalarmhyst ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select1
Devicesetup►Detailedsetup► Displayset►Lineselect►Line1 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select2
Devicesetup►Detailedsetup► Displayset►Lineselect►Line2 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select3
Devicesetup►Detailedsetup► Displayset►Lineselect►Line3 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select4
Devicesetup►Detailedsetup► Displayset►Lineselect►Line4 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select5
Devicesetup►Detailedsetup► Displayset►Lineselect►Line5 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select6
Devicesetup►Detailedsetup► Displayset►Lineselect►Line6 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select7
Devicesetup►Detailedsetup► Displayset►Lineselect►Line7 ― ―
Devicerootmenu► Detailedsetup► Display ► Line select ► Display select8
Devicesetup►Detailedsetup► Displayset►Lineselect►Line8 ― ―
Devicerootmenu► Detailedsetup► Display ► Displayformat► DisplayformatPV
Devicesetup►Detailedsetup► Displayset►Dispformat►FormatPV ― ―
Devicerootmenu► Detailedsetup► Display ► Displayoperationconfiguration► Display line
Devicesetup►Detailedsetup► Displayset►Optionalconfig►Linemode ― ―
Devicerootmenu► Detailedsetup► Display ► Displayoperationconfiguration► Display installation
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►Dispinstall ― ―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Tag
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►TagNo ― ―
<4. Functions> 90
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Long tag
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►Longtag ― ―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Electrode size
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►Electrodesize ―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Basic model code
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Model code
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Suffixconfig1
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Suffixconfig1
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Suffixconfig2
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Suffixconfig2
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 1
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Option 1
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 2
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Option 2
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 3
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Option 3
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 4
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►MScode► Option 4
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor basic model code
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Model code
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remotesensorsuffixconfig1
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Suffixconfig1
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remotesensorsuffixconfig2
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Suffixconfig2
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 1
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Option 1
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 2
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Option 2
―
<4. Functions> 91
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 3
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Option 3
―
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 4
Devicesetup►Detailedsetup► Deviceinfo►Orderinfo►RSMScode► Option 4
―
Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Transmitter serial No
Devicesetup►Detailedsetup► Deviceinfo►Ver/Numinfo►TransserialNo ―
Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Sensor serial No
Devicesetup►Detailedsetup► Deviceinfo►Ver/Numinfo►SensorserialNo ―
Diagnosticrootmenu► Diagnosis ► Adhesion ►Adhesionfunction
Devicesetup►Diag/Service►Diagnosis►Adhesion►Function
Diagnosticrootmenu► Diagnosis ► Adhesion ► Adhesion level 1
Devicesetup►Diag/Service►Diagnosis►Adhesion►Thresholdlevel1 ―
Diagnosticrootmenu► Diagnosis ► Adhesion ► Adhesion level 2
Devicesetup►Diag/Service►Diagnosis►Adhesion►Thresholdlevel2 ―
Diagnosticrootmenu► Diagnosis ► Adhesion ► Adhesion level 3
Devicesetup►Diag/Service►Diagnosis►Adhesion►Thresholdlevel3 ―
Diagnosticrootmenu► Diagnosis ► Adhesion ► Adhesion level 4
Devicesetup►Diag/Service►Diagnosis►Adhesion►Thresholdlevel4 ―
Diagnosticrootmenu► Diagnosis ► Adhesion ► Adhesion check cycle
Devicesetup►Diag/Service►Diagnosis►Adhesion►Checkcycle ―
Diagnosticrootmenu► Diagnosis ► Flow noise ►Flownoisefunction
Devicesetup►Diag/Service►Diagnosis►Flownoise►Function ―
Diagnosticrootmenu► Diagnosis ► Flow noise ► Flow noise level 1
Devicesetup►Diag/Service►Diagnosis►Flownoise►Thresholdlevel1 ―
Diagnosticrootmenu► Diagnosis ► Flow noise ► Flow noise level 2
Devicesetup►Diag/Service►Diagnosis►Flownoise►Thresholdlevel2 ―
Diagnosticrootmenu► Diagnosis ► Flow noise ► Flow noise level 3
Devicesetup►Diag/Service►Diagnosis►Flownoise►Thresholdlevel3 ―
Diagnosticrootmenu► Diagnosis ► Flow noise ► Flow noise level 4
Devicesetup►Diag/Service►Diagnosis►Flownoise►Thresholdlevel4 ―
Diagnosticrootmenu► Diagnosis ► Flow noise ► Flow noise damping
Devicesetup►Diag/Service►Diagnosis►Flownoise►Damp ―
Diagnosticrootmenu► Diagnosis ► Flow noise ► Flow noise span
Devicesetup►Diag/Service►Diagnosis►Flownoise►Span
Diagnosticrootmenu► Diagnosis ► Conductivity► Lowconductivityfunction
Devicesetup►Diag/Service►Diagnosis►Conductivity►Function ―
Diagnosticrootmenu► Diagnosis ►Conductivity► Conductivitylowlimit
Devicesetup►Diag/Service►Diagnosis►Conductivity►Lowlimit ―
<4. Functions> 92
IM 01E22A02-02EN
Alarm nameBackup
Restore
HART communication Display Duplicate Data
Restore Data
Compulsion Data
Restore Factory
Diagnosticrootmenu► Diagnosis ► Coilinsulationthreshold
Devicesetup►Diag/Service►Diagnosis►Coilinsulthreshold ―
Diagnosticrootmenu► Diagnosis ► IEXcompare
Devicesetup►Diag/Service►Diagnosis►IEXcompare ―
Diagnosticrootmenu► Diagnosis ► Diagnosticoutput
Devicesetup►Diag/Service►Diagnosis►Diagnosticoutput ―
Maintenancerootmenu► Verification► VF mode
Devicesetup►Diag/Service►Verification►Mode ―
Maintenancerootmenu► Verification► VF No
Devicesetup►Diag/Service►Verification►VF No ―
Maintenancerootmenu► Test ► Release time
Devicesetup►Diag/Service►Test► Release time ―
<4. Functions> 93
IM 01E22A02-02EN
4.13.4 Data Logging FunctionThedataloggingfunctioncanbestoreduptofourprocessvaluestothemicroSDcardwhenthe optional code MC (microSD card) is selected. Whenusingthisfunction,itispossibletospecifythefilename,datastorageinterval,anddataloggingfunctionendingtime.Thestoreddataissavedinthe“YOKOGAWA”folderasa“.TRD”file.Thedataloggingfunctioncanbeconfiguredwiththefollowingparameters.
Display menu path:Devicesetup►Diag/Service►Datalog►(see below)File name Specifythenameofthefiletobestored.Interval time Specifythedatastorageinterval.*1Start date Displays the date to start the data logging
function.Start time Displays the time to start the data logging
function.End time Specifythetimetoendthedatalogging
function.*2Log 1 Specifyprocessvalue1tobestored.*3Log 2 Specifyprocessvalue2tobestored.*3Log 3 Specifyprocessvalue3tobestored.*3Log 4 Specifyprocessvalue4tobestored.*3Execute Specifiestheexecutionofthedata
loggingfunction.*4
HART communication:Maintenancerootmenu►Datalogging► (see below)File name Specifythenameofthefiletobestored.Interval time Specifythedatastorageinterval.*1Start date Displays the date to start the data logging
function.Start time Displays the time to start the data logging
function.End time Specifythetimetoendthedatalogging
function.*2Log1 select Specifyprocessvalue1tobestored.*3Log2 select Specifyprocessvalue2tobestored.*3Log3 select Specifyprocessvalue3tobestored.*3Log4 select Specifyprocessvalue4tobestored.*3Logging Exe Specifiestheexecutionofthedata
loggingfunction.*4
*1: From the table below, select the data storage interval.1 s Sets the storage interval to 1 sec.10 s Sets the storage interval to 10 sec.30 s Sets the storage interval to 30 sec.1 min Sets the storage interval to 1 min.5 min Sets the storage interval to 5 min.30 min Sets the storage interval to 30 min.1 h Setsthestorageintervalto1hour.
*2: Fromthetablebelow,selectthedataloggingfunctionendingtime.
10 min Setstheendingtimeto10minuteslater.30 min Setstheendingtimeto30minuteslater.1 h Setstheendingtimeto1hourlater.3 h Setstheendingtimeto3hourslater.12 h Setstheendingtimeto12hourslater.24 h Setstheendingtimeto24hours(1day)later.72 h Setstheendingtimeto72hours(3days)later.240 h Setstheendingtimeto240hours(10days)
later.
*3: Fromthetablebelow,selecttheprocessvaluetobestored.PV StorestheprocessvaluethatisPV-mappedin
Subsection4.1.2.Velocity Storestheflowvelocity.Volumeflow Storesthevolumetricflowrate.Massflow Storesthemassflowrate.Calorie Stores the calorie.Adhesion Storestheresistancevalueoftheelectrode
adhesion detection.Flow noise Storestheflownoisevalue.Electrode A StoresthevoltageofelectrodeA.Electrode B StoresthevoltageofelectrodeB.V peak Storesthepeakvalueoftheflowratesignal.
*4: Fromthetablebelow,selecttheuseofthedataloggingfunction.
NotExecute Doesnotexecutethedataloggingfunction.Execute Executesthedataloggingfunction.
DataisstoredinthemicroSDcardatthespecifiedstorageintervalduringtheperiodfromthestartofthedataloggingfunctiontotheend.Thefilestoredbythedataloggingfunctioncanbeopenedasatextfile.Example:Ifthestorageintervalissetto“1min”,data is stored as shown below.
F0437.ai
…………
…………
Date and time Process value 1
Process value 2
Process value 3
Process value 4
2017/01/0112:00:002017/01/0112:01:002017/01/0112:02:002017/01/0112:03:002017/01/0112:04:002017/01/0112:05:00
+9.9863E-01+9.9909E-01+9.9906E-01+9.9859E-01+9.9870E-01+9.9829E-01
+2.8235E+01+2.8248E+01+2.8248E+01+2.8234E+01+2.8237E+01+2.8226E+01
+1.4117E+04+1.4124E+04+1.4124E+04+1.4117E+04+1.4118E+04+1.4113E+04
+4.5600E-01+3.9717E-01+3.1753E-01+4.0430E-01+3.6609E-01+4.1892E-01
The access ongoing to the microSD card can be confirmedbytheicononthedisplay.Forexample,theiconsof“microSDcardready”and“AccesstomicroSD card” are displayed alternately repeatedly whiletheinstrumentaccessestothemicroSDcardperiodicallyduringitsdatalogging.Theiconof“ErroraccessingmicroSDcard”isdisplayed when the micorSD card cannot be accessedinsuchacaseofremovingit.Insert the microSD card again when it is necessary tousethisfunctionagain.Andanalarmof“microSDfailure”occurswhenthemicroSDcardhasanyproblems.
ReadyformicroSDcard
Accessing microSD card
Disable to access microSD card
<4. Functions> 94
IM 01E22A02-02EN
IMPORTANT• Whenusingthedataloggingfunction,besuretospecifythedateandtimeinformation.
• Beforeusingthedataloggingfunction,makesurethatthemicroSDcardisprepared.Approximately1minuteisrequireduntiltheinsturmentisreadytostoredataafterithasbeenturnedon.
• Notethatthedateandtimeinformationareresetifthisinstrumentisturnedoff.
• Notethat,ifthemicroSDcardrunsoutoffreespace,thesubsequentdatawillnotbestored.
4.14 Software Write Protection Function
The write protection can be changed by the hardware write protection switch or the parameter settingofthesoftwarewriteprotection.Whenthewriteprotectionisenabledbyanyofthem,datawritingisforbidden.Fordetailsaboutthehardwarewriteprotection,seetheInstallationManualaslisted in Table 1.1.Toenablethesoftwarewriteprotectionfunction,specify“Newpassword”(eightalphanumericcharacterswithoutlowercaseletter)asapasswordtodisablethewriteprotectionfunction.Byenteringthepasswordinthemenuof“Enablewrite”,itispossible to disable the write protection and change theparametersonlyfor10minutes.Thewriteprotectioniscompletelydisabledifeightspacesareenteredto“Newpassword”inthestatethattheprotection is disabled temporarily.Thewriteprotectionfunctioncanbeconfiguredbythefollowingprocedure.
Display menu path:Devicesetup►Detailedsetup►Protection►(see below)Writeprotectsts Indicatestheuseofthewriteprotection
function.*1Enable write Cancelsthewriteprotectionfunctiononly
for10minutes.New password Specifyanewpasswordforthewrite
protectionfunction.
HART communication:Devicerootmenu►Detailedsetup► Protection►(seebelow)Writeprotect Indicatestheuseofthewriteprotection
function.*1Enable write 10 min Cancelsthewriteprotectionfunctiononly
for10minutes.New password Specifyanewpasswordforthewrite
protectionfunction.
*1:DisplayoftheusestatusofthewriteprotectionfunctionNo Thewriteprotectionfunctionisdisabled.
(Parameters can be changed.)Yes Thewriteprotectionfunctionisenabled.
(Parameters cannot be changed.)
NOTETheusestatusofthewriteprotectionfunctioncanbeviewedusingtheparametersortheiconsshown on the display.Thefollowingiconsaredisplayed.
Icon ContentsWriteprotectInvalid(Parameter change is possible)WriteprotectValid(Parameter change is impossible)
NOTEWhenthewriteprotectionswitchontheamplifierboardisturnedon,anyparametercannotbechanged.To change a parameter, cancel the write protectionfunctionusingthepre-specifiedpassword,andspecifyanewpassword.
Ifthepasswordhadbeenforgotten,itispossibletousetheJokerpasswordtotemporarilydisablethesoftwarewriteprotectionfunction.WhenthewriteprotectionfunctionisdisabledusingtheJokerpassword,“Break”isdisplayedastheparameter.Re-setanewpasswordtousethisfunction.Whenthisfunctionisdisabledusinganewpassword,theparameterreturnsto“Keep”.TheuseoftheJokerpasswordsealcanbecheckedbythefollowingprocedure.
Display menu path:Devicesetup►Detailedsetup►Protection►(see below)Softsealstatus ChecktheuseoftheJokerpassword.
<4. Functions> 95
IM 01E22A02-02EN
HART communication:Devicerootmenu►Detailedsetup► Protection►(seebelow)Softwareseal ChecktheuseoftheJokerpassword.
ChecktheuseoftheJokerpassworddependingonthefollowingparameters.Keep NormalBreak Disablethewriteprotectionfunction
usingtheJokerpassword.
NOTEIfitisnecessarytousetheJokerpassword,contactYokogawasalesofficeorrepresentative.
<5. Parameters of Magnetic Flowmeter> 96
IM 01E22A02-02EN
5. Parameters of Magnetic FlowmeterThis chapter describes the display parameters, HARTcommunicationparameters.
Thededicatedparametersareconfiguredasspecifiedatthetimeofordering.Otherparametersaresettodefaultvalues;therefore,whenchanginganyoneofthem,alwaysreadthischapter.
IMPORTANTIftheinstrumentisturnedoffwithin30secondsafterparametersettingshavebeencompleted,thesettingsarereset.Aftersettings,besuretokeepthepoweronfor30secondsormore.
NOTEToobtainthecorrectflowratesignal,specifythenominalsizeofthesensor,flowratespan,andmeterfactor.Thisinstrumenthasthenominalsizeofthesensorandthemeterfactorspecifieduponshipmentfromthemanufacturingplant,whichdoesnotrequireuser’ssettings.Thededicatedparametersareconfiguredbeforeshipmentonlywhentheyarespecifiedatthetimeofordering.Parametersthatarenotspecifiedatthetimeoforderingmustbeconfiguredbytheuser.
NOTETheavailablefunctionsandthedisplayedparameters vary depending on the connection terminaltypeselectedatthetimeofordering.
: Parameter displayed
Terminal function DescriptionCommunication and I/O code
JA JB JC JD JE JF JG JH JJ JKCurrentoutput1 ParametersrelatedtotheCurrentoutput1aredisplayed
regardlessofthecodeselection.
Currentoutput2 ParametersrelatedtotheCurrentoutput2maynotbedisplayed depending on the code selection. No.7-6 to 7-10, 7-21 to 7-23, and 13-9
Pulse/Statusoutput1 ParametersrelatedtothePulse/Statusoutput1aredisplayedregardlessofthecodeselection.
Pulse/Statusoutput2 ParametersrelatedtothePulse/Statusoutput2maynotbedisplayed depending on the code selection. No.5-11 to 22, and 13-10 to 13-11
Statusoutput3 ParametersrelatedtotheStatusoutput3maynotbedisplayed depending on the code selection. No.6-1 to 6-2, and 13-13
Statusinput ParametersrelatedtotheStatusinputmaynotbedisplayeddepending on the code selection. No.6-3 to 6-5, and 13-14
Currentinput ParametersrelatedtotheCurrentinputmaynotbedisplayed depending on the code selection. No.7-11 to 7-17, 7-24 to 7-26, 8-13 to 8-21, 13-5, and 13-12
<5. Parameters of Magnetic Flowmeter> 97
IM 01E22A02-02EN
5.1 Parameter Lists for Display and HART Communication
Eachparameterlistconsistsofthefollowingitems.No. Indicatestheparameternumber.
Name Indicates the parameter name.
Setting
Indicatestheparameterthatcanbedisplayedand/orspecified.R:Displayedonly.RW:Displayedandspecified.However,whenchangingaparameteronthedisplay,notethatthespecifiableparametersvarydepending on the operation level.Operator:Canonlyspecifythelanguagetobedisplayedonthedisplayandtheconfigurationparameters. Maintenance:Canonlyspecifythe“Operator”operationlevelandthezero-adjustmentparameters. Specialist:Canspecifyalltheparameters.
Range
For selection-type data, the range indicates options.Fornumeric-typedata,therangeindicatesthesettingrangeandthenumberofdecimalplaces.Foralphanumeric-typedata,therangeindicatesthelimitednumberofcharacters.
Default value
Indicatesthedefaultvalueuponshipmentfromthemanufacturingplant.Symbol (*) indicates a parameter with the model andsuffixcodespecified,oraparameterspecifiedatthetimeofordering.
Unit Indicatestheunitofthedatarange.Description Describesthecontentsoftheparameter.
<5. Parameters of Magnetic Flowmeter> 98
IM 01E22A02-02EN
(1) Display parametersThislistshowsthedisplayparameterssuchastheflowrateandtotalizedvalue.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
1-1 Processvariablesrootmenu►Dynamicvariables►PV%rnge
Devicesetup►Processvariables►Flowrate%
R -99999.9 to +99999.9Numberofdecimalplaces: 3
-99999.9 to +99999.9Numberofdecimalplaces: 1
- % IndicatestherangeratefortheprocessvaluethatisPV-mapped in No. 3-14.
1-2 Processvariablesrootmenu►Dynamicvariables►PV
Devicesetup►Processvariables►Flow rate
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
IndicatestheprocessvaluethatisPV-mappedinNo.3-14.
1-3 Processvariablesrootmenu►Viewoutputs► AO1current
Devicesetup►Processvariables►Analogout1
R 0.000 to +99.999Numberofdecimalplaces: 3
0.000 to +99.999Numberofdecimalplaces: 3
- mA UsedforI/O1terminal.Indicatesthecurrentvalueofthecurrentoutput.
1-4 Processvariablesrootmenu►Devicevariables►Totalizer1
Devicesetup►Processvariables►Totalizer►Totalizer1
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 4-1.
Indicatesthetotalizedvalueoftotalizer1.
1-5 Processvariablesrootmenu►Devicevariables►Totalizer2
Devicesetup►Processvariables►Totalizer►Totalizer2
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 4-10.
Indicatesthetotalizedvalueoftotalizer2.
1-6 Processvariablesrootmenu►Devicevariables►Totalizer3
Devicesetup►Processvariables►Totalizer►Totalizer3
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 4-19.
Indicatesthetotalizedvalueoftotalizer3.
1-7 Processvariablesrootmenu►Totalizercount►Totalizer1count
Devicesetup►Processvariables►Totalizer►Totalizer1count
R -INF(**) to +INF(**)Numberofdecimalplaces: 0
-999999 to +999999Numberofdecimalplaces: 0
- - Indicatesthetotalizedvalue(totalizervalue)scaledbytotalizer 1.
1-8 Processvariablesrootmenu►Totalizercount►Totalizer2count
Devicesetup►Processvariables►Totalizer►Totalizer2count
R -INF(**) to +INF(**)Numberofdecimalplaces: 0
-999999 to +999999Numberofdecimalplaces: 0
- - Indicatesthetotalizedvalue(totalizervalue)scaledbytotalizer 2.
1-9 Processvariablesrootmenu►Totalizercount►Totalizer3count
Devicesetup►►Processvariables►Totalizer►Totalizer3count
R -INF(**) to +INF(**)Numberofdecimalplaces: 0
-999999 to +999999Numberofdecimalplaces: 0
- - Indicatesthetotalizedvalue(totalizervalue)scaledbytotalizer 3.
1-10 Processvariablesrootmenu►Devicevariables►Velocity
Devicesetup►Processvariables►Velocity
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 3-15.
Indicatestheflowvelocity.
1-11 Processvariablesrootmenu►Devicevariables►Volumeflow
Devicesetup►Processvariables►Volume
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 3-16 and No. 3-19.
Indicatesthevolumetricflowrate.
1-12 Processvariablesrootmenu►Devicevariables►Massflow
Devicesetup►Processvariables►Mass
R -999999 to +999999Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 3-17 and No. 3-19.
Indicatesthemassflowrate.
1-13 Processvariablesrootmenu►Viewoutputs►AO2current
Devicesetup►Processvariables►Analogout2
R 0.000 to +99.999Numberofdecimalplaces: 3
0.000 to +99.999Numberofdecimalplaces: 3
- mA UsedforI/O3orI/O4terminal.Indicatesthecurrentvalueofthecurrentoutput.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 99
IM 01E22A02-02EN
(2)EasyconfigurationparametersThislistshowstheparametersforthefrequently-usedgeneralfunctions.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
2-1 Devicerootmenu►Detailedsetup►Display►Displayoperationconfiguration►Language
Devicesetup►Language
RW EnglishFrenchGermanItalianSpanishPortugueseRussianChineseJapanese
EnglishFrenchGermanItalianSpanishPortugueseRussianChineseJapanese
English - Specifythelanguagetobeusedonthedisplay.Synchronized with No. 10-21.
2-2 Devicerootmenu►Basicsetup►Volumeflow►VolumeflowdampingAO/frequency
Devicesetup►Easysetupwizard►Volume►DampAO/F
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforcurrentoutputorfrequencyoutput.Specifythedampingtimeconstantofthevolumetricflowrate.Synchronized with No. 3-12.
2-3 Devicerootmenu►Basicsetup►Volumeflow►Volumeflowdampingpulse/total
Devicesetup►Easysetupwizard►Volume►Damppls/ttl
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforpulseoutputortotalization.Specifythedampingtimeconstantofthevolumetricflowrate.Synchronized with No. 3-13.
2-4 Devicerootmenu►Basicsetup►Volumeflow►Volumeflowunit
Devicesetup►Easysetupwizard►Volume►Unit
RW MLm3kLl(liter)cm3kcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)
Ml(Megaliter)m3
kl(kiloliter)l(liter)cm3
kcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)
m3 (*) - Specifytheunitofthevolumetricflowrate.Synchronized with No. 3-16.
2-5 Devicerootmenu►Basicsetup►Volumeflow►Timeunit
Devicesetup►Easysetupwizard►Volume►Timeunit
RW /s/min/h/d
/s/min/h/d
/h(*) - Specifythetimeunitofthevolumetricflowrate,massflowrate,andcalorie.Synchronized with No. 3-19.
2-6 Devicerootmenu►Basicsetup►Volumeflow►Volumeflowspan
Devicesetup►Easysetupwizard►Volume►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 1 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
1.00 (*) SpecifiedinNo. 3-16 and No. 3-19.
Specifythespanofthevolumetricflowrate.Synchronized with No. 3-21.
2-7 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1rateunit
Devicesetup►Easysetupwizard►Pulse/Statusout►P1unit
RW nunit/Puunit/Pmunit/PUnit/Pkunit/PMunit/PnP/unituP/unitmP/unitP/unitkP/unitMP/unit
nunit/Puunit/Pmunit/PUnit/Pkunit/PMunit/PnP/unituP/unitmP/unitP/unitkP/unitMP/unit
Unit/P(*) - UsedforpulseoutputoftheI/O2terminal.Specifythepulseratescaling.Synchronized with No. 5-4.
2-8 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1ratevalue
Devicesetup►Easysetupwizard►Pulse/Statusout►P1 val
RW 0.00000 to +INF(**)Numberofdecimalplaces: 1 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 SpecifiedinNo.5-4
UsedforpulseoutputoftheI/O2terminal.Specifythepulseratevalue.Synchronized with No. 5-5.
2-9 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Frequency1at0%
Devicesetup►Easysetupwizard►Pulse/Statusout►F1at0%
RW 0 to 12500Numberofdecimalplaces: 0
0 to 12500Numberofdecimalplaces: 0
0 Hz UsedforfrequencyoutputoftheI/O2terminal.Specifythefrequencythatisavailablewhen0%issettotheprocessvaluePV-mappedinNo.3-14.Synchronized with No. 5-8.
2-10 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Frequency1at100%
Devicesetup►Easysetupwizard►Pulse/Statusout►F1at100%
RW 0 to 12500Numberofdecimalplaces: 0
0 to 12500Numberofdecimalplaces: 0
0 Hz UsedforfrequencyoutputoftheI/O2terminal.Specifythefrequencythatisavailablewhen100%issettotheprocessvaluePV-mappedinNo.3-14.Synchronized with No. 5-9.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 100
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
2-11 Devicerootmenu►Detailedsetup►Display►Lineselect►Display select1
Devicesetup►Easysetupwizard►Displayset►Line1
RW Flowrate(%)PVVelocityVolumeflowMassflowFlow rate(%Bar)CalorieTotalizer1Totalizer2Totalizer3TagnumberLong tagCommunProtocolAdhesionAnalogout1Analogout2Flow noise level
Flowrate(%)PVVelocityVolumeflowMassflowFlow rate(%Bar)CalorieTotalizer1Totalizer2Totalizer3TagnumberLong tagCommunProtocolAdhesionAnalogout1Analogout2Flow noise
PV - Specifyitem1tobeshownonthedisplay.Synchronized with No. 10-1.
2-12 Devicerootmenu►Detailedsetup►Display►Lineselect►Display select2
Devicesetup►Easysetupwizard►Displayset►Line2
RW NoneFlowrate(%)PVVelocityVolumeflowMassflowFlow rate(%Bar)CalorieTotalizer1Totalizer2Totalizer3TagnumberLong tagCommunProtocolAdhesionAnalogout1Analogout2Flow noise level
NoneFlowrate(%)PVVelocityVolumeflowMassflowFlow rate(%Bar)CalorieTotalizer1Totalizer2Totalizer3TagnumberLong tagCommunProtocolAdhesionAnalogout1Analogout2Flow noise
Flow rate(%)
- Specifyitem2tobeshownonthedisplay.Synchronized with No. 10-2.
2-13 Devicerootmenu►Detailedsetup►Display►Lineselect►Display select3
Devicesetup►Easysetupwizard►Displayset►Line3
RW Analog out1
- Specifyitem3tobeshownonthedisplay.Synchronized with No. 10-3.
2-14 Devicerootmenu►Basicsetup►Autozero►AutozeroExe
Devicesetup►Easysetupwizard►Autozeroexe
RW NotexecuteExecute
NotexecuteExecute
Not execute
- Specifywhethertoexecutethezeroadjustmentfunction.Synchronized with No. 3-31.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 101
IM 01E22A02-02EN
(3)BasicconfigurationparametersThislistshowstheparametersrelatedtothebasicsettingsforthesensorandotherdevices.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
3-1 Devicerootmenu►Detailedsetup►Processvariables►Velocity►VelocitydampingAO/frequency
Devicesetup►Detailedsetup►Provar►Velocity►DampAO/F
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforcurrentoutputorfrequencyoutput.Specifythedampingtimeconstantoftheflowvelocity.
3-2 Devicerootmenu►Detailedsetup►Processvariables►Velocity►Velocitydampingpulse/total
Devicesetup►Detailedsetup►Provar►Velocity►Damppls/ttl
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforpulseoutputortotalization.Specifythedampingtimeconstantoftheflowvelocity.
3-3 Devicerootmenu►Detailedsetup►Processvariables►Volumeflow►VolumeflowdampingAO/frequency
Devicesetup►Detailedsetup►Provar►Volume►DampAO/F
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforcurrentoutputorfrequencyoutput.Specifythedampingtimeconstantofthevolumetricflowrate.Synchronized with No. 2-2.
3-4 Devicerootmenu►Detailedsetup►Processvariables►Volumeflow►Volumeflowdampingpulse/total
Devicesetup►Detailedsetup►Provar►Volume►Damppls/ttl
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforpulseoutputortotalization.Specifythedampingtimeconstantofthevolumetricflowrate.Synchronized with No. 2-3.
3-5 Devicerootmenu►Detailedsetup►Processvariables►Massflow►MassflowdampingAO/frequency
Devicesetup►Detailedsetup►Provar►Mass►DampAO/F
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforcurrentoutputorfrequencyoutput.Specifythedampingtimeconstantofthemassflowrate.
3-6 Devicerootmenu►Detailedsetup►Processvariables►Massflow►Massflowdampingpulse/total
Devicesetup►Detailedsetup►Provar►Mass►Damppls/ttl
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforpulseoutputortotalization.Specifythedampingtimeconstantofthemassflowrate.
3-7 Devicerootmenu►Detailedsetup►Processvariables►Calorie►CalorificvaluedampingAO/frequency
Devicesetup►Detailedsetup►Provar►Calorie►DampAO/F
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforcurrentoutputorfrequencyoutput.Specifythedampingtimeconstantofthecalorie.
3-8 Devicerootmenu►Detailedsetup►Processvariables►Calorie►Calorificvaluedampingpulse/total
Devicesetup►Detailedsetup►Provar►Calorie►Damppls/ttl
RW +0.1to+200.0Numberofdecimalplaces: 1
+0.1to+200.0Numberofdecimalplaces: 1
3.0 s Usedforpulseoutputortotalization.Specifythedampingtimeconstantofthecalorie.
3-9 Devicerootmenu►Detailedsetup►Sensor►LowMF
Devicesetup►Detailedsetup►Sensor►LowMF
RW +0.0100to+3.0000Numberofdecimalplaces: 4
+0.0100to+3.0000Numberofdecimalplaces: 4
1.0000 (*) - Specifythelowsidefrequencymeterfactor.
3-10 Devicerootmenu►Detailedsetup►Sensor►HighMF
Devicesetup►Detailedsetup►Sensor►HighMF
RW +0.0100to+3.0000Numberofdecimalplaces: 4
+0.0100to+3.0000Numberofdecimalplaces: 4
1.0000 (*) - Specifythehighsidefrequencymeterfactor.
3-11 Devicerootmenu►Detailedsetup►Sensor►Flow sensor select
Devicesetup►Detailedsetup►Sensor►Flowsensorsel
RW ADMAGAXGADMAGAXWADMAGAXFADMAG AECalibratorOther1Other2Other3
ADMAGAXGADMAGAXWADMAGAXFADMAG AECalibratorOther1Other2Other3
ADMAG AXG(*)
- Specifythesensortype.
3-12 Devicerootmenu►Detailedsetup►Sensor►Nominalsizeunit
Devicesetup►Detailedsetup►Sensor►Nominalsizeunit
RW mminch
mminch
mm - Specifytheunitofthenominalsizeforthesensor.
3-13 Devicerootmenu►Detailedsetup►Sensor►Nominalsize
Devicesetup►Detailedsetup►Sensor►Nominalsize
RW +0.01000to+3000.0Numberofdecimalplaces: 0 to 5
+0.01000to+3000.0Numberofdecimalplaces: 0 to 5
100 (*) SpecifiedinNo. 3-12.
Specifythenominalsizeofthesensor.
3-14 Devicerootmenu►Detailedsetup►Processvariables►PVflowselect
Devicesetup►Detailedsetup►Provar►PVflowselect
RW VelocityVolumeMassDiag
VelocityVolumeMassDiag
Volume(*)
- SpecifytheprocessvaluetobePV-mapped.Velocity: Flow velocityVolume:VolumetricflowrateMass:MassflowrateDiag: Flow noise
3-15 Devicerootmenu►Detailedsetup►Processvariables►Velocity►Velocityunit
Devicesetup►Detailedsetup►Provar►Velocity►Unit
RW m/sft/s
m/sft/s
m/s(*) - Specifytheunitoftheflowvelocity.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 102
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
3-16 Devicerootmenu►Detailedsetup►Processvariables►Volumeflow►Volumeflowunit
Devicesetup►Detailedsetup►Provar►Volume►Unit
RW MLm3kLl(liter)cm3kcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)
Ml(Megaliter)m3
kl(kiloliter)l(liter)cm3
kcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)
m3 (*) - Specifytheunitofthevolumetricflowrate.Synchronized with No. 2-4.
3-17 Devicerootmenu►Detailedsetup►Processvariables►Massflow►Massflowunit
Devicesetup►Detailedsetup►Provar►Mass►Unit
RW tkggklblb
tkggklblb
kg (*) - Specifytheunitofthemassflowrate.
3-18 Devicerootmenu►Detailedsetup►Processvariables►Calorie►Calorificunit
Devicesetup►Detailedsetup►Provar►Calorie►Unit
RW MJkJJkcalcalBTU
MJkJJkcalcalBTU
J - Specifytheunitofthecalorie.
3-19 Devicerootmenu►Detailedsetup►Processvariables►Volumeflow►TimeunitorDevicerootmenu►Detailedsetup►Processvariables►Massflow►TimeunitorDevicerootmenu►Detailedsetup►Processvariables►Calorie►Timeunit
Devicesetup►Detailedsetup►Provar►Volume►TimeunitorDevicesetup►Detailedsetup►Provar►Mass►TimeunitorDevicesetup►Detailedsetup►Provar►Calorie►Timeunit
RW /s/min/h/d
/s/min/h/d
/h(*) - Specifythetimeunitofthevolumetricflowrate,massflowrate,andcalorie.Synchronized with No. 2-5.
3-20 Devicerootmenu►Detailedsetup►Processvariables►Velocity►Velocityspan
Devicesetup►Detailedsetup►Provar►Velocity►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 0 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
1.00000 (*)
SpecifiedinNo. 3-15.
Specifythespanoftheflowvelocity.
3-21 Devicerootmenu►Detailedsetup►Processvariables►Volumeflow►Volumeflowspan
Devicesetup►Detailedsetup►Provar►Volume►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 0 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
1.00000 (*)
SpecifiedinNo. 3-16 and No. 3-19.
Specifythespanofthevolumetricflowrate.Synchronized with No. 2-6.Specifythevalueequivalentto1m/sincaseofnoorderinginformationbyuser.
3-22 Devicerootmenu►Detailedsetup►Processvariables►Massflow►Massflowspan
Devicesetup►Detailedsetup►Provar►Mass►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 0 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
1.00000 (*)
SpecifiedinNo. 3-17 and No. 3-19.[kg/h]
Specifythespanofthemassflowrate.
3-23 Devicerootmenu►Detailedsetup►Processvariables►Calorie►Calorificflowspan
Devicesetup►Detailedsetup►Provar►Calorie►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 0 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
1.00000 SpecifiedinNo. 3-18 and No. 3-19.[J/h]
Specifythespanofthecalorie.
3-24 Devicerootmenu►Detailedsetup►Processvariables►Velocity check
Devicesetup►Detailedsetup►Provar►Velocitycheck
R -99.999 to +99.999Numberofdecimalplaces: 3
-99.999 to +99.999Numberofdecimalplaces: 3
- m/s ConvertstheprocessvaluePV-mappedinNo.3-14tothespanoftheflowvelocity,anddisplaystheconvertedvalue.
3-25 Devicerootmenu►Detailedsetup►Userspan►User span select AO1
Devicesetup►Detailedsetup►UserSpan►UserspanAO1►Select
RW NoYes
NoYes
No - UsedforcurrentoutputoftheI/O1terminal.Specifywhetherthespecialunitcanbesettotheprocessvalue.
3-26 Devicerootmenu►Detailedsetup►Userspan►UserunitAO1
Devicesetup►Detailedsetup►UserSpan►UserspanAO1►Unit
RW ASCII 8 characters
ASCII 8 characters
All Space - UsedforcurrentoutputoftheI/O1terminal.Specifythespecialunitfortheprocessvalue.
3-27 Devicerootmenu►Detailedsetup►Userspan►UserspanAO1
Devicesetup►Detailedsetup►UserSpan►UserspanAO1►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 0 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
100.000 - UsedforcurrentoutputoftheI/O1terminal.Specifythespecialunitspanfortheprocessvalue.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 103
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
3-28 Devicerootmenu►Detailedsetup►Userspan►User span select AO2
Devicesetup►Detailedsetup►UserSpan►UserspanAO2►Select
RW NoYes
NoYes
No - UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifywhetherthespecialunitcanbesettotheprocessvalue.
3-29 Devicerootmenu►Detailedsetup►Userspan►UserunitAO2
Devicesetup►Detailedsetup►UserSpan►UserspanAO2►Unit
RW ASCII 8 characters
ASCII 8 characters
All Space - UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifythespecialunitfortheprocessvalue.
3-30 Devicerootmenu►Detailedsetup►Userspan►UserspanAO2
Devicesetup►Detailedsetup►UserSpan►UserspanAO2►Span
RW +0.00001to+INF(**)Numberofdecimalplaces: 0 to 5
+0.00001to+999999Numberofdecimalplaces: 0 to 5
100.000 - UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifythespecialunitspanfortheprocessvalue.
3-31 Devicerootmenu►Basicsetup►Autozero►AutozeroExe
Devicesetup►Diag/Service►Autozero►Execute
RW NotexecuteExecute
NotexecuteExecute
Not execute
- Specifywhethertoexecutethezeroadjustmentfunction.Synchronized with No. 2-14.
3-32 Maintenancerootmenu►Autozero►Result►Zerovalue
Devicesetup►Diag/Service►Autozero►Result►Zerovalue
RW -99.999 to +99.999Numberofdecimalplaces: 3
-99.999 to +99.999Numberofdecimalplaces: 3
0.000 cm/s Indicatestheresultofexecutingthezeroadjustmentfunction.Manualinputispossible.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 104
IM 01E22A02-02EN
(4)TotalizationconfigurationparametersThislistshowstheparametersrelatedtothetotalizationfunction.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
4-1 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1unit
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Unit
R MLm3
kLl(liter)cm3
tkggkcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)klb(US)lb(US)
Ml(Megaliter)m3
kl(kiloliter)l(liter)cm3
tkggkcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)klb(US)lb(US)
- - Indicatestheunitoftotalizer1(processvaluePV-mapped in No. 3-14).
4-2 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1convfactor
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Convfactor
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
1.00000 (*)
Synchronized with No. 4-1.
Specifytheconversionfactorforscalingtotalizer1.
4-3 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1lowcut
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Calorie: SpecifiedinNo. 3-18 and No. 3-19.
Specifythelow-cutvalueoftotalizer1.
4-4 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1failopts
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Failureopts
RW RunHoldLast valid
RunHoldLast valid
Run - Specifythetotalizer1operationtobeperformedwhenan alarm has activated.Run:Continuesthetotalizationfunctionafteranalarmhas activated.Hold:Stopsthetotalizationfunctionafteranalarmhasactivated.Lastvalid:Continuesthetotalizationfunctionwiththelastvalidvaluebeforeanalarmactivates.
4-5 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1 options
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Options
RW BalancedAbsoluteOnly positiveOnly negativeHold
BalancedAbsoluteOnly positiveOnly negativeHold
Only positive
- Specifythetotalizationdirectionoftotalizer1.Balanced:Totalizesthedifferentialflowratebetweentheforwardandreversedirections.Absolute:Totalizestheabsolutevalueoftheflowrate.Onlypositive:Totalizesonlytheflowrateintheforwarddirection.Onlynegative:Totalizesonlytheflowrateinthereverse direction.Hold:Stopstotalizationprocessing(holdsthecurrenttotalized-value).
4-6 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1Start/Stop
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Start/Stop
RW StopStart
StopStart
Stop - Specifywhethertoexecutethetotalizationfunctionoftotalizer 1.
4-7 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1Reset/Preset
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Reset/Preset
RW NotexecuteResetPreset
NotexecuteResetPreset
Not execute
- Specifywhethertoexecutetheresetorpresetfunctionoftotalizer1.
4-8 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1presetvalue
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Presetvalue
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
0.00000 Volumetricflowrate:Specifiedin No. 3-16.Massflowrate:SpecifiedinNo. 3-17.Calorie: SpecifiedinNo. 3-18.
Specifythepresetvalueoftotalizer1.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)indicatesaparameter,onlyifthecurrentinputisenabled.
<5. Parameters of Magnetic Flowmeter> 105
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
4-9 Devicerootmenu►Detailedsetup►Totalizer►Totalizer1►Total1 set point
Devicesetup►Detailedsetup►Totalizer►Totalizer1►Set point
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 Volumetricflowrate:Specifiedin No. 3-16.Massflowrate:SpecifiedinNo. 3-17.Calorie: SpecifiedinNo. 3-18.
Specifythetargetvalueatwhichthestatusoutputoftotalizer 1 becomes active.
4-10 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2unit
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Unit
RW MLm3
kLl(liter)cm3
tkggkcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)klb(US)lb(US)MJ(***)kJ(***)J(***)kcal (***)cal (***)BTU (***)
Ml(Megaliter)m3
kl(kiloliter)l(liter)cm3
tkggkcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)klb(US)lb(US)MJ(***)kJ(***)J(***)kcal (***)cal (***)BTU (***)
m3 - Specifytheunitoftotalizer2.
4-11 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2convfactor
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Convfactor
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
1.00000 SpecifiedinNo. 4-10.
Specifytheconversionfactorforscalingtotalizer2.
4-12 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2lowcut
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 SpecifiedinNo. 4-10 and No.3-19.
Specifythelow-cutvalueoftotalizer2.
4-13 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2failopts
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Failureopts
RW RunHoldLast valid
RunHoldLast valid
Run - Specifythetotalizer2operationtobeperformedwhenan alarm has activated.Run:Continuesthetotalizationfunctionafteranalarmhas activated.Hold:Stopsthetotalizationfunctionafteranalarmhasactivated.Lastvalid:Continuesthetotalizationfunctionwiththelastvalidvaluebeforeanalarmactivates.
4-14 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2 options
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Options
RW BalancedAbsoluteOnly positiveOnly negativeHold
BalancedAbsoluteOnly positiveOnly negativeHold
Only negative
- Specifythetotalizationdirectionoftotalizer2.Balanced:Totalizesthedifferentialflowratebetweentheforwardandreversedirections.Absolute:Totalizestheabsolutevalueoftheflowrate.Onlypositive:Totalizesonlytheflowrateintheforwarddirection.Onlynegative:Totalizesonlytheflowrateinthereverse direction.Hold:Stopstotalizationprocessing(holdsthecurrenttotalized-value).
4-15 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2Start/Stop
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Start/Stop
RW StopStart
StopStart
Stop - Specifywhethertoexecutethetotalizationfunctionoftotalizer 2.
4-16 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2Reset/Preset
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Reset/Preset
RW NotexecuteResetPreset
NotexecuteResetPreset
Not execute
- Specifywhethertoexecutetheresetorpresetfunctionoftotalizer2.
4-17 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2presetvalue
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Presetvalue
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
0.00000 SpecifiedinNo. 4-10.
Specifythepresetvalueoftotalizer2.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)indicatesaparameter,onlyifthecurrentinputisenabled.
<5. Parameters of Magnetic Flowmeter> 106
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
4-18 Devicerootmenu►Detailedsetup►Totalizer►Totalizer2►Total2 set point
Devicesetup►Detailedsetup►Totalizer►Totalizer2►Set point
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 SpecifiedinNo. 4-10.
Specifythetargetvalueatwhichthestatusoutputoftotalizer 2 becomes active.
4-19 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3unit
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Unit
RW MLm3
kLl(liter)cm3
tkggkcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)klb(US)lb(US)MJ(***)kJ(***)J(***)kcal (***)cal (***)BTU (***)
Ml(Megaliter)m3
kl(kiloliter)l(liter)cm3
tkggkcfcfmcfMgal(US)kgal(US)gal(US)mgal(US)kbbl(US Oil)bbl(US Oil)mbbl(US Oil)ubbl(USOil)kbbl(US Beer)bbl(US Beer)mbbl(US Beer)ubbl(USBeer)klb(US)lb(US)MJ(***)kJ(***)J(***)kcal (***)cal (***)BTU (***)
m3 - Specifytheunitoftotalizer3.
4-20 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3convfactor
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Convfactor
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
1.00000 SpecifiedinNo. 4-19.
Specifytheconversionfactorforscalingtotalizer3.
4-21 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3lowcut
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 SpecifiedinNo. 4-19 and No.3-19.
Specifythelow-cutvalueoftotalizer3.
4-22 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3failopts
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Failureopts
RW RunHoldLast valid
RunHoldLast valid
Run - Specifythetotalizer3operationtobeperformedwhenan alarm has activated.Run:Continuesthetotalizationfunctionafteranalarmhas activated.Hold:Stopsthetotalizationfunctionafteranalarmhasactivated.Lastvalid:Continuesthetotalizationfunctionwiththelastvalidvaluebeforeanalarmactivates.
4-23 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3 options
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Options
RW BalancedAbsoluteOnly positiveOnly negativeHold
BalancedAbsoluteOnly positiveOnly negativeHold
Balanced - Specifythetotalizationdirectionoftotalizer3.Balanced:Totalizesthedifferentialflowratebetweentheforwardandreversedirections.Absolute:Totalizestheabsolutevalueoftheflowrate.Onlypositive:Totalizesonlytheflowrateintheforwarddirection.Onlynegative:Totalizesonlytheflowrateinthereverse direction.Hold:Stopstotalizationprocessing(holdsthecurrenttotalized-value).
4-24 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3Start/Stop
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Start/Stop
RW StopStart
StopStart
Stop - Specifywhethertoexecutethetotalizationfunctionoftotalizer 3.
4-25 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3Reset/Preset
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Reset/Preset
RW NotexecuteResetPreset
NotexecuteResetPreset
Not execute
- Specifywhethertoexecutetheresetorpresetfunctionoftotalizer3.
4-26 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3presetvalue
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Presetvalue
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
0.00000 SpecifiedinNo. 4-19.
Specifythepresetvalueoftotalizer3.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)indicatesaparameter,onlyifthecurrentinputisenabled.
<5. Parameters of Magnetic Flowmeter> 107
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
4-27 Devicerootmenu►Detailedsetup►Totalizer►Totalizer3►Total3 set point
Devicesetup►Detailedsetup►Totalizer►Totalizer3►Set point
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 SpecifiedinNo. 4-19.
Specifythetargetvalueatwhichthestatusoutputoftotalizer 3 becomes active.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)indicatesaparameter,onlyifthecurrentinputisenabled.
<5. Parameters of Magnetic Flowmeter> 108
IM 01E22A02-02EN
(5)PulseoutputconfigurationparametersThislistshowstheparametersrelatedtothefrequencyoutputorpulseoutputoftheI/O2terminal,I/O3terminal,andI/O4terminal,andthestatusoutputoftheI/O3terminal.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
5-1 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1outputmode
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Outputmode
RW NofunctionFixedpulseFrequencyoutputStatusoutput
NofunctionFixedpulseoutputFrequencyoutputStatusoutput
Fixed pulse
- SpecifytheoutputoftheI/O2terminal.Nofunction:NooutputFixedpulse:FixedpulseoutputFrequencyoutput:Frequencyoutput(Duty50%)Statusoutput:Statusoutput
5-2 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1activemode
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Activemode
RW On activeOffactive
On activeOffactive
On active - UsedforpulseoutputoftheI/O2terminal.Specifytheactivedirectionofthepulsesignal.
5-3 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1fixwidth
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Fixwidth
RW 0.05 ms0.1 ms0.5 ms1 ms20 ms33 ms50 ms100 ms200 ms330 ms500 ms1000 ms2000 ms
0.05 ms0.1 ms0.5 ms1 ms20 ms33 ms50 ms100 ms200 ms330 ms500 ms1000 ms2000 ms
0.05 ms - UsedforpulseoutputoftheI/O2terminal.Specifythepulsewidth.
5-4 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1rateunit
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Rateunit
RW nunit/Puunit/Pmunit/PUnit/Pkunit/PMunit/PnP/unituP/unitmP/unitP/unitkP/unitMP/unit
nunit/Puunit/Pmunit/PUnit/Pkunit/PMunit/PnP/unituP/unitmP/unitP/unitkP/unitMP/unit
Unit/P(*) - UsedforpulseoutputoftheI/O2terminal.Specifythepulseratescaling.Synchronized with No. 2-7.
5-5 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1ratevalue
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Ratevalue
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 (*) SpecifiedinNo. 5-4.
UsedforpulseoutputoftheI/O2terminal.Specifythepulseratevalue.Synchronized with No. 2-8.
5-6 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1lowcut
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
UsedforfrequencyoutputorpulseoutputoftheI/O2terminal.Specifythelow-cutvalue.
5-7 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Pulse1alarmout
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Alarmout
RW 0 ppsMeasuredvalueHoldMax pps
0 ppsMeasuredvalueHoldMax pps
0 pps - UsedforfrequencyoutputorpulseoutputoftheI/O2terminal.Specifytheoutputoperationtobeperformedwhenanalarm has activated.0pps:NooutputMeasuredvalue:Outputsthefrequencyorpulsewiththemeasuredvalue.Hold:Outputsthefrequencyorpulsewiththelastvalidvaluebeforeanalarmactivates.Maxpps:Outputsthefrequencyorpulseat12500pps.
5-8 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Frequency1at0%
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Frequencyat0%
RW 0 to 12500Numberofdecimalplaces: 0
0 to 12500Numberofdecimalplaces: 0
0 Hz UsedforfrequencyoutputoftheI/O2terminal.Specifythefrequencythatisavailablewhen0%issettotheprocessvaluePV-mappedinNo.3-14.Synchronized with No. 2-9.
5-9 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Frequency1at100%
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►Frequencyat100%
RW 0 to 12500Numberofdecimalplaces: 0
0 to 12500Numberofdecimalplaces: 0
0 Hz UsedforfrequencyoutputoftheI/O2terminal.Specifythefrequencythatisavailablewhen100%issettotheprocessvaluePV-mappedinNo.3-14.Synchronized with No. 2-10.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 109
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
5-10 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput1►Statusoutput1function
Devicesetup►Detailedsetup►Pulse/Statusout►PO1/SO1►SO1function
RW NofunctionAlarmoutputWarningoutputTotal limit 1Total limit 2Total limit 3H/LalarmHH/LLalarmFwd/RevrangeAuto2rangeExt2 answer
NofunctionAlarmoutputWarningoutputTotal limit 1Total limit 2Total limit 3H/LalarmHH/LLalarmFwd/RevrangeAuto2rangeExt2 answer
No function
- SpecifythestatusoutputfunctionoftheI/O2terminal.Nofunction:NooutputAlarmoutput:Thestatusoutputbecomesactivewhenan alarm activates.Warningoutput:Thestatusoutputbecomesactivewhenawarningoccurs.Totallimit1:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer1isexceedingthetargetvalue.Totallimit2:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer2isexceedingthetargetvalue.Totallimit3:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer3isexceedingthetargetvalue.H/Lalarm:ThestatusoutputisactivewhiletheprocessvaluePV-mappedinNo.3-14isoutofthelowlimitvalueorhighlimitvalue.HH/LLalarm:ThestatusoutputisactivewhiletheprocessvaluePV-mappedinNo.3-14isoutofthelow-lowlimitvalueorhigh-highlimitvalue.Fwd/Revrange:Thestatusoutputisactivewhilethefluidisflowinginthereversedirection.Auto2range:Thestatusoutputisactivewhileoperationisbeingperformedinrange2.Ext2answer:Thestatusoutputbecomesactivedependingontherangeusedforthestatusinput.
5-11 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2activepulse
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Activepulse
RW NormalMagnetic counter
NormalFor magnetic counter
Normal - UsedforpulseoutputoftheI/O3orI/O4terminal.Specifywhethertoenableordisabletheoutputforthemagneticcounter.Normal:NormaloutputMagneticcounter:Outputformagneticcounter
5-12 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2outputmode
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Outputmode
RW NofunctionFixedpulseFrequencyoutputStatusoutput
NofunctionFixedpulseoutputFrequencyoutputStatusoutput
No function
- SpecifytheoutputoftheI/O3orI/O4terminal.Nofunction:NooutputFixedpulse:FixedpulseoutputFrequencyoutput:Frequencyoutput(Duty50%)Statusoutput:Statusoutput
5-13 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2select
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Pulseselect
RW Non-ConnectVelocityVolumeflowMassflowCalorieDiag
Non-ConnectVelocityVolumeflowMassflowCalorieDiag
Non-Connect
- SpecifytheprocessvaluetobeoutputthroughtheI/O3terminalorI/O4terminal.Non-Connect:NooutputVelocity:Setstheflowvelocitytotheoutput.Volumeflow:Setsthevolumetricflowratetotheoutput.Massflow:Setsthemassflowratetotheoutput.Calorie:Setsthecalorietotheoutput.Diag:Setstheflownoisetotheoutput.
5-14 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2activemode
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Activemode
RW On activeOffactive
On activeOffactive
On active - UsedforpulseoutputoftheI/O3orI/O4terminal.Specifytheactivedirectionofthepulsesignal.
5-15 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2fixwidth
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Fixwidth
RW 0.05 ms0.1 ms0.5 ms1 ms20 ms33 ms50 ms100 ms200 ms330 ms500 ms1000 ms2000 ms
0.05 ms0.1 ms0.5 ms1 ms20 ms33 ms50 ms100 ms200 ms330 ms500 ms1000 ms2000 ms
0.05 ms - UsedforpulseoutputoftheI/O3orI/O4terminal.Specifythepulsewidth.
5-16 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2rateunit
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Rateunit
RW nunit/Puunit/Pmunit/PUnit/Pkunit/PMunit/PnP/unituP/unitmP/unitP/unitkP/unitMP/unit
nunit/Puunit/Pmunit/PUnit/Pkunit/PMunit/PnP/unituP/unitmP/unitP/unitkP/unitMP/unit
Unit/P - UsedforpulseoutputoftheI/O3orI/O4terminal.Specifythepulseratescaling.
5-17 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2ratevalue
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Ratevalue
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 SpecifiedinNo. 5-16.
UsedforpulseoutputoftheI/O3orI/O4terminal.Specifythepulseratevalue.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 110
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
5-18 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2lowcut
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
UsedforfrequencyoutputandpulseoutputoftheI/O3orI/O4terminal.Specifythelow-cutvalue.
5-19 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Pulse2alarmout
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Alarmout
RW 0 ppsMeasuredvalueHoldMax pps
0 ppsMeasuredvalueHoldMax pps
0 pps - UsedforfrequencyoutputandpulseoutputoftheI/O3orI/O4terminal.Specifytheoutputoperationtobeperformedwhenanalarm has activated.0pps:NooutputMeasuredvalue:Outputsthefrequencyorpulsewiththemeasuredvalue.Hold:Outputsthefrequencyorpulsewiththelastvalidvaluebeforeanalarmactivates.Maxpps:Outputsthefrequencyorpulseat12500pps.
5-20 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Frequency2at0%
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Frequencyat0%
RW 0 to 12500Numberofdecimalplaces: 0
0 to 12500Numberofdecimalplaces: 0
0 Hz UsedforfrequencyoutputoftheI/O3orI/O4terminal.Specifythefrequencythatisavailablewhen0%issettotheprocessvaluemappedinNo.5-13.
5-21 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Frequency2at100%
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►Frequencyat100%
RW 0 to 12500Numberofdecimalplaces: 0
0 to 12500Numberofdecimalplaces: 0
0 Hz UsedforfrequencyoutputoftheI/O3orI/O4terminal.Specifythefrequencythatisavailablewhen100%issettotheprocessvaluemappedinNo.5-13.
5-22 Devicerootmenu►Detailedsetup►Pulse/Status►Pulse/Statusoutput2►Statusoutput2function
Devicesetup►Detailedsetup►Pulse/Statusout►PO2/SO2►SO2function
RW NofunctionAlarmoutputWarningoutputTotal limit 1Total limit 2Total limit 3H/LalarmHH/LLalarmFwd/RevrangeAuto2rangeExt2 answer
NofunctionAlarmoutputWarningoutputTotal limit 1Total limit 2Total limit 3H/LalarmHH/LLalarmFwd/RevrangeAuto2rangeExt2 answer
No function
- SpecifythestatusoutputfunctionoftheI/O3orI/O4terminal.Nofunction:NooutputAlarmoutput:Thestatusoutputbecomesactivewhenan alarm activates.Warningoutput:Thestatusoutputbecomesactivewhenawarningoccurs.Totallimit1:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer1isexceedingthetargetvalue.Totallimit2:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer2isexceedingthetargetvalue.Totallimit3:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer3isexceedingthetargetvalue.H/Lalarm:ThestatusoutputisactivewhiletheprocessvaluePV-mappedinNo.3-14isoutofthelowlimitvalueorhighlimitvalue.HH/LLalarm:ThestatusoutputisactivewhiletheprocessvaluePV-mappedinNo.3-14isoutofthelow-lowlimitvalueorhigh-highlimitvalue.Fwd/Revrange:Thestatusoutputisactivewhilethefluidisflowinginthereversedirection.Auto2range:Thestatusoutputisactivewhileoperationisbeingperformedinrange2.Ext2answer:Thestatusoutputbecomesactivedependingontherangeusedforthestatusinput.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 111
IM 01E22A02-02EN
(6)Statusinput-outputconfigurationparametersThislistshowstheparametersrelatedtothestatusinput-outputoftheI/O3terminal,andmultirange.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
6-1 Devicerootmenu►Detailedsetup►Pulse/Status►Statusoutput3►Statusoutput3activemode
Devicesetup►Detailedsetup►Pulse/Statusout►SO3►Active mode
RW On activeOffactive
On activeOffactive
On active - UsedforstatusoutputoftheI/O3terminal.Specifytheactivedirectionofthetargetsignal.
6-2 Devicerootmenu►Detailedsetup►Pulse/Status►Statusoutput3►Statusoutput3function
Devicesetup►Detailedsetup►Pulse/Statusout►SO3►Function
RW NofunctionAlarmoutputWarningoutputTotal limit 1Total limit 2Total limit 3H/LalarmHH/LLalarmFwd/RevrangeAuto2rangeExt 2 answer
NofunctionAlarmoutputWarningoutputTotal limit 1Total limit 2Total limit 3H/LalarmHH/LLalarmFwd/RevrangeAuto2rangeExt 2 answer
No function
- SpecifythestatusoutputfunctionoftheI/O3terminal.Nofunction:NooutputAlarmoutput:Thestatusoutputbecomesactivewhenan alarm activates.Warningoutput:Thestatusoutputbecomesactivewhenawarningoccurs.Totallimit1:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer1isexceedingthetargetvalue.Totallimit2:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer2isexceedingthetargetvalue.Totallimit3:Thestatusoutputisactivewhilethetotalizedvalueoftotalizer3isexceedingthetargetvalue.H/Lalarm:ThestatusoutputisactivewhiletheprocessvaluePV-mappedinNo.3-14isoutofthelowlimitvalueorhighlimitvalue.HH/LLalarm:ThestatusoutputisactivewhiletheprocessvaluePV-mappedinNo.3-14isoutofthelow-lowlimitvalueorhigh-highlimitvalue.Fwd/Revrange:Thestatusoutputisactivewhilethefluidisflowinginthereversedirection.Auto2range:Thestatusoutputisactivewhileoperationisbeingperformedinrange2.Ext2answer:Thestatusoutputbecomesactivedependingontherangeusedforthestatusinput.
6-3 Devicerootmenu►Detailedsetup►Pulse/Status►Statusinput3►Statusinput3activemode
Devicesetup►Detailedsetup►Statusin►SI3►Active mode
RW Short(On) actOpen(Off)act
Short(On) actOpen(Off)act
Short (On) act
- UsedforstatusinputoftheI/O3terminal.Specifytheactivedirectionofthetargetsignal.Short(On)act:Activewhenshort-circuited.Open(Off)act:Activewhenopened.
6-4 Devicerootmenu►Detailedsetup►Pulse/Status►Statusinput3►Statusinput3function
Devicesetup►Detailedsetup►Statusin►SI3►Function
RW Nofunction0%SignalLockExtautozeroTotal preset 1Total preset 2Total preset 3Ext2 ranges
Nofunction0%SignalLockExtautozeroTotal preset 1Total preset 2Total preset 3Ext2 ranges
No function
- SelectthestatusinputfunctionoftheI/O3terminal.Nofunction:Noinput0%SignalLock:Whenthestatusinputbecomesactive,thecurrentoutputoftheI/O1terminalisfixedto 4 mA.Extautozero:Whenthestatusinputbecomesactive,thezero-adjustmentfunctionisperformed.Totalpreset1:Whenthestatusinputbecomesactive,thepresetvalueissettototalizer1,andtotalizationstartsbasedonthevalue.Totalpreset2:Whenthestatusinputbecomesactive,thepresetvalueissettototalizer2,andtotalizationstartsbasedonthevalue.Totalpreset3:Whenthestatusinputbecomesactive,thepresetvalueissettototalizer3,andtotalizationstartsbasedonthevalue.Ext2ranges:Whenthestatusinputbecomesactive,thecurrentoutputrangeisswitchedfromrange1torange 2.
6-5 Devicerootmenu►Detailedsetup►Pulse/Status►Statusinput3►Statusinput3state
Devicesetup►Detailedsetup►Statusin►SI3►Status
R OpenShort
OpenShort
- - UsedforstatusinputoftheI/O3terminal.Indicatestheterminalstatus.
6-6 Devicerootmenu►Detailedsetup►Multirange►Forwardspan2
Devicesetup►Detailedsetup►Multirange►Forwardspan2
RW 0.00001 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00001 to +999999Numberofdecimalplaces: 0 to 5
1.0 Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
Usedformultirange.Specifythevalueofforwardrange2.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 112
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
6-7 Devicerootmenu►Detailedsetup►Multirange►Reversespan1
Devicesetup►Detailedsetup►Multirange►Reversespan1
RW 0.00001 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00001 to +999999Numberofdecimalplaces: 0 to 5
1.0 Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
Usedformultirange.Specifythevalueofreverserange1.
6-8 Devicerootmenu►Detailedsetup►Multirange►Reversespan2
Devicesetup►Detailedsetup►Multirange►Reversespan2
RW 0.00001 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00001 to +999999Numberofdecimalplaces: 0 to 5
1.0 Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
Usedformultirange.Specifythevalueofreverserange2.
6-9 Devicerootmenu►Detailedsetup►Multirange►Autorangehyst
Devicesetup►Detailedsetup►Multirange►Autorangehyst
RW 0 to 15Numberofdecimalplaces: 0
0 to 15Numberofdecimalplaces: 0
10 % Usedformultirange.Specifytherangeswitchinghysteresis.
6-10 Devicerootmenu►Detailedsetup►Multirange►Bidirectionhyst
Devicesetup►Detailedsetup►Multirange►Bidirectionhyst
RW 0 to 8Numberofdecimalplaces: 0
0 to 8Numberofdecimalplaces: 0
2 % Usedforforwardandreverseranges.Specifytherangeswitchinghysteresis.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 113
IM 01E22A02-02EN
(7) Display parametersThislistshowstheparametersrelatedtothecurrentoutputoftheI/O1terminal,I/O3terminal,andI/O4terminal,andthecurrentinputoftheI/O4terminal.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
7-1 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput1►AO1lowcut
Devicesetup►Detailedsetup►Analogout/in►AO1►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 Flow velocity: SpecifiedinNo. 3-15.Volumetricflowrate:Specifiedin No. 3-16 and No. 3-19.Massflowrate:SpecifiedinNo. 3-17 and No. 3-19.Flow noise: cm/s
UsedforcurrentoutputoftheI/O1terminal.Specifythelow-cutvalue.
7-2 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput1►AO1 high limit
Devicesetup►Detailedsetup►Analogout/in►AO1►Highlimit
RW +4.0to+21.6Numberofdecimalplaces: 3
+4.000to+21.600Numberofdecimalplaces: 3
20.500 mA UsedforcurrentoutputoftheI/O1terminal.Specifythehighlimitvalueofthecurrent.
7-3 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput1►AO1 low limit
Devicesetup►Detailedsetup►Analogout/in►AO1►Low limit
RW +2.4to+20.0Numberofdecimalplaces: 3
+2.400to+20.000Numberofdecimalplaces: 3
3.800 mA UsedforcurrentoutputoftheI/O1terminal.Specifythelowlimitvalueofthecurrent.
7-4 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput1►AO1alarmout
Devicesetup►Detailedsetup►Analogout/in►AO1►Alarmout
RW <2.4mA3.8 mA4 mA20.5 mA>21.6mAMeasuredvalueHold
<2.4mA3.8 mA4 mA20.5 mA>21.6mAMeasuredvalueHold
>21.6mA
- UsedforcurrentoutputoftheI/O1terminal.Specifythecurrentoutputthatisavailablewhenanalarm has activated.<2.4mA:Outputsthelowercurrentthan2.4mA.3.8mA:Outputsthecurrentof3.8mA.4mA:Outputsthecurrentof4mA.20.5mA:Outputsthecurrentof20.5mA.>21.6mA:Outputsthehighercurrentthan21.6mA.Measuredvalue:Outputsthemeasuredcurrentvalue(indefinite).Hold:Outputsthecurrentthatisappliedwhenanalarmhas activated.
7-5 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput1►AO1 range mode
Devicesetup►Detailedsetup►Analogout/in►AO1►Range mode
RW Normal rangeAbs range
Normal rangeAbs range
Normal range
- Specifywhethertoexecutetheabsoluterangefunction.Normal range: Normal rangeAbsrange:Absoluterange
7-6 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput2►AO2 select
Devicesetup►Detailedsetup►Analogout/in►AO2►AO2 select
RW Non-ConnectVelocityVolumeflowMassflowCalorieDiag
Non-ConnectVelocityVolumeflowMassflowCalorieDiag
Non-Connect
- SpecifytheprocessvalueusedtooutputthecurrentthroughtheI/O3terminalorI/O4terminal.Non-Connect:NooutputVelocity:Setstheflowvelocitytotheoutput.Volumeflow:Setsthevolumetricflowratetotheoutput.Massflow:Setsthemassflowratetotheoutput.Calorie:Setsthecalorietotheoutput.Diag:Setstheflownoisetotheoutput.
7-7 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput2►AO2lowcut
Devicesetup►Detailedsetup►Analogout/in►AO2►Lowcut
RW 0.00000 to +INF(**)Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.0 Synchronized with No. 7-6.
UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifythelow-cutvalue.
7-8 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput2►AO2 high limit
Devicesetup►Detailedsetup►Analogout/in►AO2►Highlimit
RW +4.0to+21.6Numberofdecimalplaces: 3
+4.000to+21.600Numberofdecimalplaces: 3
20.500 mA UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifythehighlimitvalueofthecurrent.
7-9 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput2►AO2 low limit
Devicesetup►Detailedsetup►Analogout/in►AO2►Low limit
RW +2.4to+20.0Numberofdecimalplaces: 3
+2.400to+20.000Numberofdecimalplaces: 3
3.800 mA UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifythelowlimitvalueofthecurrent.
7-10 Devicerootmenu►Detailedsetup►Analogoutput/input►Analogoutput2►AO2alarmout
Devicesetup►Detailedsetup►Analogout/in►AO2►Alarmout
RW <2.4mA3.8 mA4 mA20.5 mA>21.6mAMeasuredvalueHold
<2.4mA3.8 mA4 mA20.5 mA>21.6mAMeasuredvalueHold
>21.6mA
- UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifythecurrentoutputthatisavailablewhenanalarm has activated.<2.4mA:Outputsthelowercurrentthan2.4mA.3.8mA:Outputsthecurrentof3.8mA.4mA:Outputsthecurrentof4mA.20.5mA:Outputsthecurrentof20.5mA.>21.6mA:Outputsthehighercurrentthan21.6mA.Measuredvalue:Outputsthemeasuredcurrentvalue(indefinite).Hold:Outputsthecurrentthatisappliedwhenanalarmhas activated.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 114
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
7-11 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AIfunction
Devicesetup►Detailedsetup►Analogout/in►AI►Function
RW NofunctionMonitoringDifftemperatureExt temperature
NofunctionMonitoringDifftemperatureExt temperature
No function
- SpecifythecurrentinputfunctionoftheI/O4terminal.Nofunction:NocurrentinputMonitoring:Setsthetemperaturetotheinput(tochecktemperatureinformation).Difftemperature:Setsthetemperaturedifferencetotheinput.Exttemperature:Setstheabsolutetemperaturetotheinput.
7-12 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AIHighlimit
Devicesetup►Detailedsetup►Analogout/in►AI►Highlimit
RW +4.0to+21.6Numberofdecimalplaces: 3
+4.000to+21.600Numberofdecimalplaces: 3
20.500 mA UsedforcurrentinputoftheI/O4terminal.Specifythehighlimitvalueofthecurrent.
7-13 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AI Low limit
Devicesetup►Detailedsetup►Analogout/in►AI►Low limit
RW +2.4to+20.0Numberofdecimalplaces: 3
+2.400to+20.000Numberofdecimalplaces: 3
3.800 mA UsedforcurrentinputoftheI/O4terminal.Specifythelowlimitvalueofthecurrent.
7-14 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AICurrent
Devicesetup►Detailedsetup►Analogout/in►AI►Value
R 0.000 to +22.730Numberofdecimalplaces: 3
0.000 to +22.730Numberofdecimalplaces: 3
0.000 mA UsedforcurrentinputoftheI/O4terminal.Indicatesthecurrentvalue.
7-15 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AIunit
Devicesetup►Detailedsetup►Analogout/in►AI►Unit
RW deg Cdeg FK
deg Cdeg FK
deg C - UsedforcurrentinputoftheI/O4terminal.Specifytheunitofthetemperature.
7-16 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AIURV
Devicesetup►Detailedsetup►Analogout/in►AI►URV
RW -999.9 to +999.9Numberofdecimalplaces: 1
-999.9 to +999.9Numberofdecimalplaces: 1
120.0 SpecifiedinNo. 7-15.
UsedforcurrentinputoftheI/O4terminal.Specifythehighlimitvalue(20mA)oftheprocessvalueusedtoinputthecurrent.
7-17 Devicerootmenu►Detailedsetup►Analogoutput/input►Analoginput►AILRV
Devicesetup►Detailedsetup►Analogout/in►AI►LRV
RW -999.9 to +999.9Numberofdecimalplaces: 1
-999.9 to +999.9Numberofdecimalplaces: 1
0.0 SpecifiedinNo. 7-15.
UsedforcurrentinputoftheI/O4terminal.Specifythelowlimitvalue(4mA)oftheprocessvalueusedtoinputthecurrent.
7-18 Maintenancerootmenu►AO/AItrim►AOtrim►ClearD/Atrim1
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO1trimclear
RW NotexecuteExecute
NotexecuteExecute
Not execute
- UsedforcurrentoutputoftheI/O1terminal.Clearstheadjustmentvaluetooutputthecurrent.
7-19 Maintenancerootmenu►AO/AItrim►AOtrim►AO1 Trim
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO1trim4mA
RW 3.200 to 5.600Numberofdecimalplaces: 3
3.200 to 5.600Numberofdecimalplaces: 3
4.000 mA UsedforcurrentoutputoftheI/O1terminal.Specifytheadjustmentvaluetooutputthecurrentwith4 mA.
7-20 Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO1trim20mA
RW 18.400 to 21.600Numberofdecimalplaces: 3
18.400 to 21.600Numberofdecimalplaces: 3
20.000 mA UsedforcurrentoutputoftheI/O1terminal.Specifytheadjustmentvaluetooutputthecurrentwith20 mA.
7-21 Maintenancerootmenu►AO/AItrim►AOtrim►ClearD/Atrim2
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO2trimclear
RW NotexecuteExecute
NotexecuteExecute
Not execute
- UsedforcurrentoutputoftheI/O3orI/O4terminal.Clearstheadjustmentvaluetooutputthecurrent.
7-22 Maintenancerootmenu►AO/AItrim►AOtrim►AO2 Trim
Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO2trim4mA
RW 3.200 to 5.600Numberofdecimalplaces: 3
3.200 to 5.600Numberofdecimalplaces: 3
4.000 mA UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifytheadjustmentvaluetooutputthecurrentwith4 mA.
7-23 Devicesetup►Diag/Service►AO/AItrim►AOtrim►AO2trim20mA
RW 18.400 to 21.600Numberofdecimalplaces: 3
18.400 to 21.600Numberofdecimalplaces: 3
20.000 mA UsedforcurrentoutputoftheI/O3orI/O4terminal.Specifytheadjustmentvaluetooutputthecurrentwith20 mA.
7-24 Maintenancerootmenu►AO/AItrim►AItrim►Clear AI trim
Devicesetup►Diag/Service►AO/AItrim►AItrim►Trimclear
RW NotexecuteExecute
NotexecuteExecute
Not execute
- UsedforcurrentinputoftheI/O4terminal.Clearstheadjustmentvaluetooutputthecurrent.
7-25 Maintenancerootmenu►AO/AItrim►AItrim►AI Trim
Devicesetup►Diag/Service►AO/AItrim►AItrim►Trim4mA
RW 3.200 to 5.600Numberofdecimalplaces: 3
3.200 to 5.600Numberofdecimalplaces: 3
4.000 mA UsedforcurrentinputoftheI/O4terminal.Specifytheadjustmentvaluetooutputthecurrentwith4 mA.
7-26 Devicesetup►Diag/Service►AO/AItrim►AItrim►Trim20mA
RW 18.400 to 21.600Numberofdecimalplaces: 3
18.400 to 21.600Numberofdecimalplaces: 3
20.000 mA UsedforcurrentinputoftheI/O4terminal.Specifytheadjustmentvaluetooutputthecurrentwith20 mA.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 115
IM 01E22A02-02EN
(8)AuxiliaryfunctionconfigurationparametersThislistshowstheparametersrelatedtotheflowratedirection,ratelimit,low-cutvalue,temperaturecorrectionforthedensity,andcaloriecalculation.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
8-1 Devicerootmenu►Detailedsetup►AUXcalculation►Flow direction
Devicesetup►Detailedsetup►AUXcalculation►Flow direct
RW ForwardReverse
ForwardReverse
Forward - Specifythefluidflowdirection.
8-2 Devicerootmenu►Detailedsetup►AUXcalculation►Rate limit
Devicesetup►Detailedsetup►AUXcalculation►Rate limit
RW 0.0 to 10.0Numberofdecimalplaces: 1
0.0 to 10.0Numberofdecimalplaces: 1
5.0 % Specifytheratelimitvalue.
8-3 Devicerootmenu►Detailedsetup►AUXcalculation►Dead time
Devicesetup►Detailedsetup►AUXcalculation►Dead time
RW 0.0 to 15.0Numberofdecimalplaces: 1
0.0 to 15.0Numberofdecimalplaces: 1
0.0 s Specifythedeadtime.
8-4 Devicerootmenu►Detailedsetup►AUXcalculation►Noisefilter
Devicesetup►Detailedsetup►AUXcalculation►Noisefilter
RW ManualLevel1Level2Level3
ManualLevel1Level2Level3
Manual - Specifythenoisefilter(ratelimitvalueanddeadtime).
8-5 Devicerootmenu►Detailedsetup►AUXcalculation►Pulsingflow
Devicesetup►Detailedsetup►AUXcalculation►Pulsingflow
RW NoYes
NoYes
No - Specifywhethertoexecutethepulsingflowsupportfunction.
8-6 Devicerootmenu►Detailedsetup►AUXcalculation►Power synchronize
Devicesetup►Detailedsetup►AUXcalculation►Powersyncon/off
RW OffOn
OffOn
Off - Specifywhethertheexcitationfrequencyandpowerfrequencyaresynchronousorasynchronous.
8-7 Devicerootmenu►Detailedsetup►AUXcalculation►Setpowerfrequency
Devicesetup►Detailedsetup►AUXcalculation►Setpowerfreq
RW 47.00 to 63.00Numberofdecimalplaces: 2
47.00 to 63.00Numberofdecimalplaces: 2
50.00 Hz Whentheexcitationfrequencyandpowerfrequencyareasynchronous,specifythepowerfrequencythatsynchronizeswiththeexcitationfrequency.(Thedefaultvalueissetas49.00for500mm(16in.)or larger sizes.)
8-8 Devicerootmenu►Detailedsetup►AUXcalculation►IEXpowerfrequency
Devicesetup►Detailedsetup►AUXcalculation►Iexpowerfrequency
R 0.00 to 99.99Numberofdecimalplaces: 2
0.00 to 99.99Numberofdecimalplaces: 2
- Hz Indicatesthepowerfrequencythatsynchronizeswiththeexcitationfrequency.
8-9 Devicerootmenu►Detailedsetup►AUXcalculation►Mespowerfrequency
Devicesetup►Detailedsetup►AUXcalculation►Measpowerfreq
R 0.00 to 99.99Numberofdecimalplaces: 2
0.00 to 99.99Numberofdecimalplaces: 2
- Hz Indicatesthemeasuredvalueofthepowerfrequency.FortheDCpower,thisparameterindicates“0.00Hz”.
8-10 Devicerootmenu►Detailedsetup►Processvariables►Density►Densityvalueselect
Devicesetup►Detailedsetup►Provar►Density►Valueselect
RW FixedvalueCorrectvalue
FixedvalueCorrection value
Fixed value
- Specifywhethertoexecutethetemperaturecorrectionfunctionforthedensity.Fixedvalue:UsesthedensityspecifiedinNo.8-12.Correctvalue:Usesthedensitywiththetemperaturecorrected.
8-11 Devicerootmenu►Detailedsetup►Processvariables►Density►Densityunit
Devicesetup►Detailedsetup►Provar►Density►Unit
RW kg/m3
lb/gallb/cf
kg/m3
lb/gallb/cf
kg/m3 - Specifytheunitofthedensity.
8-12 Devicerootmenu►Detailedsetup►Processvariables►Density►Densityfixedvalue
Devicesetup►Detailedsetup►Provar►Density►Fixed density
RW 0.00000 to 999999Numberofdecimalplaces: 0 to 5
0.00000 to 999999Numberofdecimalplaces: 0 to 5
0 (*) SpecifiedinNo. 8-11.
Specifythedensityvalue.
8-13 Devicerootmenu►Detailedsetup►Processvariables►Density►Standarddensity
Devicesetup►Detailedsetup►Provar►Density►Std density
RW 0.00000 to +999999Numberofdecimalplaces: 0 to 5
0.00000 to +999999Numberofdecimalplaces: 0 to 5
0 SpecifiedinNo. 8-11.
Specifythereferencedensityvaluetocorrectthetemperatureforthedensity.
8-14 Devicerootmenu►Detailedsetup►Processvariables►Temperature►Standardtemperature
Devicesetup►Detailedsetup►Provar►Temperature►Stdtemperature
RW -999.9 to +999.9Numberofdecimalplaces: 2
-999.99 to +999.99Numberofdecimalplaces: 2
20.00 SpecifiedinNo. 7-15.
Specifythereferencetemperaturevaluetocorrectthetemperatureforthedensity.
8-15 Devicerootmenu►Detailedsetup►Processvariables►Temperature►TempcoefA1
Devicesetup►Detailedsetup►Provar►Temperature►CoefA1
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0
-999999 to +999999Numberofdecimalplaces: 0 to 5-32000.0 to +32000.0
0.0 - Specifytheprimarycompensatingratetocorrectthetemperatureforthedensity.
8-16 Devicerootmenu►Detailedsetup►Processvariables►Temperature►TempcoefA2
Devicesetup►Detailedsetup►Provar►Temperature►CoefA2
RW -INF(**) to +INF(**)Numberofdecimalplaces: 0
-999999 to +999999Numberofdecimalplaces: 0 to 5-32000.0 to +32000.0
0.0 - Specifythesecondarycompensatingratetocorrectthetemperatureforthedensity.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 116
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
8-17 Devicerootmenu►Detailedsetup►Processvariables►Temperature►Measuredtemperature
Devicesetup►Detailedsetup►Provar►Temperature►Meastemperature
R -999.9 to +999.9Numberofdecimalplaces: 2
-999.99 to +999.99Numberofdecimalplaces: 2
- SpecifiedinNo. 7-15.
UsedforcurrentinputoftheI/O4terminal.Indicatesthetemperaturewiththecurrentinput.
8-18 Devicerootmenu►Detailedsetup►Processvariables►Density►Correctdensity
Devicesetup►Detailedsetup►Provar►Density►Correct density
R 0.00000 to 999999Numberofdecimalplaces: 0 to 5
0.0 to 999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 8-11.
Indicatesthedensitywiththetemperaturecorrected.
8-19 Devicerootmenu►Detailedsetup►Processvariables►Calorie►Specificheat
Devicesetup►Detailedsetup►Provar►Calorie►Specificheat
RW 0.0to+999999Numberofdecimalplaces: 1
0.0 to +99999.9Numberofdecimalplaces: 1
4184.0 J/kg*K Specifythespecificheatofthefluid.
8-20 Devicerootmenu►Detailedsetup►Processvariables►Temperature►Calorificfixtemp
Devicesetup►Detailedsetup►Provar►Temperature►Fixedtemperature
RW -999.99 to +999.99Numberofdecimalplaces: 2
-999.99 to +999.99Numberofdecimalplaces: 2
20.00 SpecifiedinNo. 7-15.
UsedforcurrentinputoftheI/O4terminal.Specifythereferencetemperaturevaluetoobtainthecaloriewhenthecurrentinputissettotheabsolutetemperature.
8-21 Processvariablesrootmenu►Devicevariables►Calorificvalue
Devicesetup►Detailedsetup►Provar►Calorie►Value
R -INF(**) to +INF(**)Numberofdecimalplaces: 0 to 5
-999999 to +999999Numberofdecimalplaces: 0 to 5
- SpecifiedinNo. 3-18 and No. 3-19.
Indicates the calorie.
8-22 Devicerootmenu►Detailedsetup►AUXcalculation►Set SIL
Devicesetup►Detailedsetup►AUXcalculation►Set SIL
RW NoYes
NoYes
No - SpecifythecurrentoutputforSafetyInstrumentedSystem application.Synchronized with No. 7-4.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 117
IM 01E22A02-02EN
(9)AlarmconfigurationparametersThislistshowstheparametersrelatedtoalarmoutput,burnout,andhistory.
No. Name Setting Range Default value Unit DescriptionHART communication Display HART communication Display9-1 Maintenancerootmenu►
High/Lowalarmconfiguration► Highalarm
Devicesetup►Diag/Service►H/Lalarmcfg►Highalarm
RW -INF(**)to+INF(**) Numberofdecimalplaces:1to5
-999999to+999999 Numberofdecimalplaces: 1 to 5
300.000 Flow velocity: Specifiedin No. 3-15.Volumetricflowrate:SpecifiedinNo. 3-16 and No. 3-19.Massflowrate:Specifiedin No. 3-17 and No. 3-19.Flownoise:cm/s
Specifythehighlimitvaluetojudgeanalarm.
9-2 Maintenancerootmenu► High/Lowalarmconfiguration► Low alarm
Devicesetup►Diag/Service►H/Lalarmcfg►Low alarm
RW -INF(**)to+INF(**) Numberofdecimalplaces:1to5
-999999to+999999 Numberofdecimalplaces: 1 to 5
-300.000 Flow velocity: Specifiedin No. 3-15.Volumetricflowrate:SpecifiedinNo. 3-16 and No. 3-19.Massflowrate:Specifiedin No. 3-17 and No. 3-19.Flownoise:cm/s
Specifythehighlimitvaluetojudgeanalarm.
9-3 Maintenancerootmenu► High/Lowalarmconfiguration► Highhighalarm
Devicesetup►Diag/Service►H/Lalarmcfg►HHalarm
RW -INF(**)to+INF(**) Numberofdecimalplaces:1to5
-999999to+999999 Numberofdecimalplaces: 1 to 5
300.000 Flow velocity: Specifiedin No. 3-15.Volumetricflowrate:SpecifiedinNo. 3-16 and No. 3-19.Massflowrate:Specifiedin No. 3-17 and No. 3-19.Flownoise:cm/s
Specifythehighlimitvaluetojudgeanalarm.
9-4 Maintenancerootmenu► High/Lowalarmconfiguration► Low low alarm
Devicesetup►Diag/Service►H/Lalarmcfg►LL alarm
RW -INF(**)to+INF(**) Numberofdecimalplaces:1to5
-999999to+999999 Numberofdecimalplaces: 1 to 5
-300.000 Flow velocity: Specifiedin No. 3-15.Volumetricflowrate:SpecifiedinNo. 3-16 and No. 3-19.Massflowrate:Specifiedin No. 3-17 and No. 3-19.Flownoise:cm/s
Specifythehighlimitvaluetojudgeanalarm.
9-5 Maintenancerootmenu► High/Lowalarmconfiguration► Hi/Loalarmhysteresis
Devicesetup►Diag/Service►H/Lalarmcfg►H/Lalarmhyst
RW 0 to 10 Numberofdecimalplaces:0
0 to 10 Numberofdecimalplaces: 0
5 % Specifythehysteresis width between the alarm occurrenceandresetting.
9-6 Diagnosticrootmenu►Status/Selftest►Alarm►Burnout
Devicesetup►Diag/Service►H/Lalarmcfg►4-20burnout
R High Low
HighLow
- - Indicates the currentoutputdirection when burnoutoccurs.
9-7 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmoutmask► Alarmoutmask1
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 1-1
RW 13:MainboardEEPROMdefaulton21:PWM1stopon22:PWM2stopon23: Option board mismatch on24:OptionEEPROMfailureon25:OptionboardA/Dfailureon26:OptionboardSPIfailureon28:Indicatorboardfailureon29: Ind EEP FAIL on30:LCDdriverfailureon31: Indicator board mismatch on32:Indicatorcommunicationerroron33:microSDfailureon
013:EEPROMdflt AllOff - Specifythemaskfunctionforalarmnotification1-1.
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 1-2
RW 021:PWM1stop022:PWM2stop023:Opt bd mismatch024: Opt bd EEP FAIL025:OptbdA/DFAIL026: Opt bd SPI FAIL028: Ind bd FAIL029: Ind bd EEP FAIL030: LCD drv FAIL031: Ind bd mismatch032: Ind comm ERR033: microSD FAIL
028: Ind bd FAIL
- Indicates the masked alarm foralarmnotification1-2.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 118
IM 01E22A02-02EN
No. Name Setting Range Default value Unit DescriptionHART communication Display HART communication Display9-7 Diagnosticrootmenu►
Status/Selftest► Alarm► Alarmoutmask► Alarmoutmask2
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 2-1
RW 50:Signaloverflowon 51: Empty pipe detection on 52:H/LHH/LLalarmon 53: Adhesion over level 4 on 60:Spanconfigurationerroron 62:Analogoutput14-20mAlimiterroron 63:Analogoutput24-20mAlimiterroron 64:Analogoutput1multirangeerroron 65:H/LHH/LLconfigurationerroron 66:Densityconfigurationerroron 67:Pulseoutput1configurationerroron 68:Pulseoutput2configurationerroron 69:Nominalsizeconfigurationerroron 70:Adhesionconfigurationerroron 71:Flownoiseconfigerroron 72: Data logging not started on 80:Analogoutput1saturatedon 81:Analogoutput2saturatedon 82:Pulseoutput1saturatedon 83:Pulseoutput2saturatedon 84:Analoginputsaturatedon 85: Cable misconnect on 86:Coilinsulationwarningon 131: Transmitter type mismatch on
050:Signaloverflow051: Empty detect052:H/LHH/LLalm053: Adh over lv 4060:SpancfgERR062: AO 1 4-20 lmt063: AO 2 4-20 lmt064: AO 1 mlt rng065:H/LcfgERR066:DensitycfgERR
052:H/LHH/LLalm053: Adh over lv 4
- Specifythemaskfunctionforalarmnotification2-1.
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 2-2
RW 067:Pls1cfgERR068:Pls2cfgERR069:Nomisizecfg070:AdhcfgERR071:FLNcfgERR072: Log not start080:AO1saturate081:AO2saturate082:Pls1saturate083:Pls2saturate084:AIsaturate085: Cable miscon086:Coilinsulation131: Trans mismatch
080: AO 1 saturate081: AO 2 saturate082: Pls 1 saturate083: Pls 2 saturate084: AI saturate086: Coil insulation
- Specifythemaskfunctionforalarmnotification2-2.
Diagnosticrootmenu► Status/Selftest► Alarm► Alarmoutmask► Alarmoutmask3
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 3-1
RW 87: Adhesion over level 3 on 88:Lowconductivitywarningon 89:Insulationdetectionon 90: Flow noise over level 3 on 91: Flow noise over level 4 on 92:Autozerowarningon 93:Verificationwarningon 94: Factory noise warning on 95:Simulationactiveon 96:Analogoutput1fixedon 97:Analogoutput2fixedon 98:Pulseoutput1fixedon 99:Pulseoutput2fixedon 100:Analoginputfixedon 101:Parameterrestorerunningon 102: Display over warning on 103: microSD card size warning on 104:Parameterbackupincompleteon 105: microSD card mismatch on 106: microSD card removal error on 120:Watchdogon 121:Poweroffon 122:Instantpowerfailureon 123:Parameterbackuprunningon 124:Dataloggingrunningon
087: Adhesion lv 3088: LC warn089:Insudetect090: FLN over lv 3091: FLN over lv 4092: AZ warn093:Verifwarn094: Fact noise warn095:Simulateactive096:AO1fix097:AO2fix098:Pls1fix099:Pls2fix100:AIfix
087: Adhesion lv 3088: LC warn089:Insudetect090: FLN over lv 3091: FLN over lv 4093:Verifwarn094: Fact noise warn
- Specifythemaskfunctionforalarmnotification3-1.
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 3-2
RW 101: Param restore run102: Disp over103: SD size warn104:Bkupincmplt105: SD mismatch106: SD removal ERR120:Watchdog121:Poweroff122:Inst power FAIL123:Parambkuprun124:Datalogrun
101: Param restorerun102: Disp over103:SD size warn104:Bkupincmplt105: SD mismatch106:SD removal ERR120:Watchdog121:Poweroff122:Inst power FAIL123:Parambkuprun124:Datalogrun
- Specifythemaskfunctionforalarmnotification3-2.
Diagnosticrootmenu► Status/Selftest► Alarm► Alarmoutmask► Alarmoutmask4
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmoutmask►Mask 4-1
RW 130: Device ID not entered on 130: DevID not enter All Space - Specifythemaskfunctionforalarmnotification4-1.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 119
IM 01E22A02-02EN
No. Name Setting Range Default value Unit DescriptionHART communication Display HART communication Display9-8 Diagnosticrootmenu►
Status/Selftest► Alarm► Alarmrecordmask► Alarm record mask 1
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecordmask►Mask 1-1
RW 13:MainboardEEPROMdefaulton20:Exciterfailureon21:PWM1stopon22:PWM1stopon23:Option board mismatch on24:OptionEEPROMfailureon25:OptionboardA/Dfailureon26:OptionboardSPIfailureon28:Indicatorboardfailureon29:Ind EEP FAIL on30:LCDdriverfailureon31:Indicator board mismatch on32:Indicatorcommunicationerroron33:microSDfailureon
013:EEPROMdflt020: Exciter FAIL
All Space - Specifythemaskfunctionforalarmhistory1-1.
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecordmask►Mask 1-2
RW 021:PWM1stop022:PWM2stop023:Opt bd mismatch024: Opt bd EEP FAIL025:OptbdA/DFAIL026: Opt bd SPI FAIL028: Ind bd FAIL029: Ind bd EEP FAIL030: LCD drv FAIL031: Ind bd mismatch032: Ind comm ERR033: microSD FAIL
All Space - Specifythemaskfunctionforalarmhistory1-2.
Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecordmask► Alarm record mask 2
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecordmask►Mask 2-1
RW 50:Signaloverflowon 51: Empty pipe detection on 52:H/LHH/LLalarmon 53: Adhesion over level 4 on 85: Cable misconnect on
050:Signaloverflow051: Empty detect052:H/LHH/LLalm053: Adh over lv 4
All Space - Specifythemaskfunctionforalarmhistory2-1.
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecordmask►Mask 2-2
RW 085: Cable miscon All Space - Specifythemaskfunctionforalarmhistory2-2.
Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecordmask► Alarm record mask 3
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecordmask►Mask 3-1
RW 130: Device ID not entered on 130: DevID not enter 130: DevID not enter
- Specifythemaskfunctionforalarmhistory3-1.
9-9 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecord► Alarm record 1
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record alarm 1
R All Space 10:MainboardCPUfailure 11:Reversecalculationfailure 12:MainboardEEPROMfailure 13:MainboardEEPROMdefault 14:Sensorboardfailure 15:Sensorcommunicationerror 16:A/D1failure[Signal] 17:A/D2failure[Exciter] 18: Coil open 19: Coil short 20:Exciterfailure 21:PWM1stop 22:PWM2stop 23: Option board mismatch 24:OptionboardEEPROMfailure 25:OptionboardA/Dfailure 26:OptionboardSPIfailure 27: Parameter restore incomplete 28:Indicatorboardfailure 29:IndicatorboardEEPROMfailure 30:LCDdriverfailure 31: Indicator board mismatch 32:Indicatorcommunicationerror 33:microSDfailure 50:Signaloverflow 51: Empty pipe detection 52:H/LorHH/LLalarm 53: Adhesion over level 4 85: Cable misconnect 130:Device ID not entered
All Space010: Main CPU FAIL011: Rev calc FAIL012: Main EEP FAIL013:EEPROMdflt014: Snsr bd FAIL015: Snsr comm ERR016: AD 1 FAIL[Sig]017: AD 2 FAIL[Excit]018: Coil open019: Coil short020: Exciter FAIL021:PWM1stop022:PWM2stop023:Opt bd mismatch024: Opt bd EEP FAIL025:OptbdA/DFAIL026: Opt bd SPI FAIL027: Restore FAIL028: Ind bd FAIL029: Ind bd EEP FAIL030: LCD drv FAIL031: Ind bd mismatch032: Ind comm ERR033: microSD FAIL050:Signaloverflow051: Empty detect052:H/LHH/LLalm053: Adh over lv 4085: Cable miscon130: DevID not enter
All Space - Indicates the nameofnewalarm 1.
9-10 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecord► Alarm record time 1
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record time 1
R 00000D 00: 00 to 99999D 23: 59 00000D 00: 00 to 99999D 23: 59
00000D 00: 00 - Indicates the operating time at which new alarm 1 has occurred.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 120
IM 01E22A02-02EN
No. Name Setting Range Default value Unit DescriptionHART communication Display HART communication Display9-11 Diagnosticrootmenu►
Status/Selftest► Alarm► Alarmrecord► Alarm record 2
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record alarm 2
R All Space 10:MainboardCPUfailure 11:Reversecalculationfailure 12:MainboardEEPROMfailure 13:MainboardEEPROMdefault 14:Sensorboardfailure 15:Sensorcommunicationerror 16:A/D1failure[Signal] 17:A/D2failure[Exciter] 18: Coil open 19: Coil short 20:Exciterfailure 21:PWM1stop 22:PWM2stop 23: Option board mismatch 24:OptionboardEEPROMfailure 25:OptionboardA/Dfailure 26:OptionboardSPIfailure 27: Parameter restore incomplete 28:Indicatorboardfailure 29:IndicatorboardEEPROMfailure 30:LCDdriverfailure 31: Indicator board mismatch 32:Indicatorcommunicationerror 33:microSDfailure 50:Signaloverflow 51: Empty pipe detection 52:H/LorHH/LLalarm 53: Adhesion over level 4 85: Cable misconnect 130:Device ID not entered
All Space010: Main CPU FAIL011: Rev calc FAIL012: Main EEP FAIL013:EEPROMdflt014: Snsr bd FAIL015: Snsr comm ERR016: AD 1 FAIL[Sig]017: AD 2 FAIL[Excit]018: Coil open019: Coil short020: Exciter FAIL021:PWM1stop022:PWM2stop023:Opt bd mismatch024: Opt bd EEP FAIL025:OptbdA/DFAIL026: Opt bd SPI FAIL027: Restore FAIL028: Ind bd FAIL029: Ind bd EEP FAIL030: LCD drv FAIL031: Ind bd mismatch032: Ind comm ERR033: microSD FAIL050:Signaloverflow051: Empty detect052:H/LHH/LLalm053: Adh over lv 4085: Cable miscon130: DevID not enter
All Space - Indicates the nameofnewalarm 2.
9-12 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecord► Alarm record time 2
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record time 2
R 00000D 00: 00 to 99999D 23: 59 00000D 00: 00 to 99999D 23: 59
00000D 00: 00 - Indicates the operating time at which new alarm 2 has occurred.
9-13 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecord► Alarm record 3
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record alarm 3
R All Space 10:MainboardCPUfailure 11:Reversecalculationfailure 12:MainboardEEPROMfailure 13:MainboardEEPROMdefault 14:Sensorboardfailure 15:Sensorcommunicationerror 16:A/D1failure[Signal] 17:A/D2failure[Exciter] 18: Coil open 19: Coil short 20:Exciterfailure 21:PWM1stop 22:PWM2stop 23: Option board mismatch 24:OptionboardEEPROMfailure 25:OptionboardA/Dfailure 26:OptionboardSPIfailure 27: Parameter restore incomplete 28:Indicatorboardfailure 29:IndicatorboardEEPROMfailure 30:LCDdriverfailure 31: Indicator board mismatch 32:Indicatorcommunicationerror 33:microSDfailure 50:Signaloverflow 51: Empty pipe detection 52:H/LorHH/LLalarm 53: Adhesion over level 4 85: Cable misconnect 130:Device ID not entered
All Space010: Main CPU FAIL011: Rev calc FAIL012: Main EEP FAIL013:EEPROMdflt014: Snsr bd FAIL015: Snsr comm ERR016: AD 1 FAIL[Sig]017: AD 2 FAIL[Excit]018: Coil open019: Coil short020: Exciter FAIL021:PWM1stop022:PWM2stop023:Opt bd mismatch024: Opt bd EEP FAIL025:OptbdA/DFAIL026: Opt bd SPI FAIL027: Restore FAIL028: Ind bd FAIL029: Ind bd EEP FAIL030: LCD drv FAIL031: Ind bd mismatch032: Ind comm ERR033: microSD FAIL050:Signaloverflow051: Empty detect052:H/LHH/LLalm053: Adh over lv 4085: Cable miscon130: DevID not enter
All Space - Indicates the nameofnewalarm 3.
9-14 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecord► Alarm record time 3
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record time 3
R 00000D 00: 00 to 99999D 23: 59 00000D 00: 00 to 99999D 23: 59
00000D 00: 00 - Indicates the operating time at which new alarm 3 has occurred.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 121
IM 01E22A02-02EN
No. Name Setting Range Default value Unit DescriptionHART communication Display HART communication Display9-15 Diagnosticrootmenu►
Status/Selftest► Alarm► Alarmrecord► Alarm record 4
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record alarm 4
R All Space 10:MainboardCPUfailure 11:Reversecalculationfailure 12:MainboardEEPROMfailure 13:MainboardEEPROMdefault 14:Sensorboardfailure 15:Sensorcommunicationerror 16:A/D1failure[Signal] 17:A/D2failure[Exciter] 18: Coil open 19: Coil short 20:Exciterfailure 21:PWM1stop 22:PWM2stop 23: Option board mismatch 24:OptionboardEEPROMfailure 25:OptionboardA/Dfailure 26:OptionboardSPIfailure 27: Parameter restore incomplete 28:Indicatorboardfailure 29:IndicatorboardEEPROMfailure 30:LCDdriverfailure 31: Indicator board mismatch 32:Indicatorcommunicationerror 33:microSDfailure 50:Signaloverflow 51: Empty pipe detection 52:H/LorHH/LLalarm 53: Adhesion over level 4 85: Cable misconnect 130:Device ID not entered
All Space010: Main CPU FAIL011: Rev calc FAIL012: Main EEP FAIL013:EEPROMdflt014: Snsr bd FAIL015: Snsr comm ERR016: AD 1 FAIL[Sig]017: AD 2 FAIL[Excit]018: Coil open019: Coil short020: Exciter FAIL021:PWM1stop022:PWM2stop023:Opt bd mismatch024: Opt bd EEP FAIL025:OptbdA/DFAIL026: Opt bd SPI FAIL027: Restore FAIL028: Ind bd FAIL029: Ind bd EEP FAIL030: LCD drv FAIL031: Ind bd mismatch032: Ind comm ERR033: microSD FAIL050:Signaloverflow051: Empty detect052:H/LHH/LLalm053: Adh over lv 4085: Cable miscon130: DevID not enter
All Space - Indicates the nameofnewalarm 4.
9-16 Diagnosticrootmenu► Status/Selftest► Alarm► Alarmrecord► Alarm record time 4
Devicesetup►Diag/Service►Sts/Selftest►Alarm►Alarmrecord►Record time 4
R 00000D 00: 00 to 99999D 23: 59 00000D 00: 00 to 99999D 23: 59
00000D 00: 00 - Indicates the operating time at which new alarm 4 has occurred.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 122
IM 01E22A02-02EN
(10) DisplayconfigurationparametersThis list shows the parameters related to display settings.
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
10-1 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select1
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 1
RW Flowrate(%) PV Velocity Volumeflow Massflow Flow rate(%Bar) Calorie Totalizer1 Totalizer2 Totalizer3 Tagnumber Long tag Communprotocol Adhesion Analogout1 Analogout2 Flow noise level
Flowrate(%) PV Velocity Volumeflow Massflow Flow rate(%Bar) Calorie Totalizer1 Totalizer2 Totalizer3 Tagnumber Long tag Communprotocol Adhesion Analogout1 Analogout2 Flow noise level
PV - Specifyitem1tobeshownonthedisplay.Synchronized with No. 2-11.
10-2 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select2
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 2
RW None Flowrate(%) PV Velocity Volumeflow Massflow Flow rate(%Bar) Calorie Totalizer1 Totalizer2 Totalizer3 Tagnumber Long tag Communprotocol Adhesion Analogout1 Analogout2 Flow noise level
None Flowrate(%) PV Velocity Volumeflow Massflow Flow rate(%Bar) Calorie Totalizer1 Totalizer2 Totalizer3 Tagnumber Long tag Communprotocol Adhesion Analogout1 Analogout2 Flow noise level
Flowrate(%) - Specifyitem2tobeshownonthedisplay.Synchronized with No. 2-12.
10-3 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select3
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 3
RW Analogout1 - Specifyitem3tobeshownonthedisplay.Synchronized with No. 2-13.
10-4 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select4
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 4
RW None - Specifyitem4tobeshownonthedisplay.
10-5 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select5
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 5
RW None - Specifyitem5tobeshownonthedisplay.
10-6 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select6
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 6
RW None - Specifyitem6tobeshownonthedisplay.
10-7 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select7
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 7
RW None - Specifyitem7tobeshownonthedisplay.
10-8 Devicerootmenu► Detailedsetup► Display► Lineselect► Display select8
Devicesetup►Detailedsetup►Displayset►Lineselect►Line 8
RW None - Specifyitem8tobeshownonthedisplay.
10-9 Devicerootmenu► Detailedsetup► Display► Displayformat► DisplayformatPV
Devicesetup►Detailedsetup►Displayset►Dispformat►Format PV
RW Auto 0 digit 1 digit 2 digit 3 digit 4 digit 5 digit
Auto 0 digit 1 digit 2 digit 3 digit 4 digit 5 digit
Auto - Specifythenumberofdecimalplaces.Auto:Automaticallyadjuststhenumberofdecimalplaces.0digit:Fixesthenumberofdecimalplacesto“0”.1digit:Fixesthenumberofdecimalplacesto“1”.2digit:Fixesthenumberofdecimalplacesto“2”.3digit:Fixesthenumberofdecimalplacesto“3”.4digit:Fixesthenumberofdecimalplacesto“4”.5digit:Fixesthenumberofdecimalplacesto“5”.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 123
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
10-10 Devicerootmenu► Detailedsetup► Display► Displayformat► Displayformattotal1
Devicesetup►Detailedsetup►Displayset►Dispformat►Format total 1
RW Auto 0 digit 1 digit 2 digit 3 digit 4 digit 5 digit 6 digit 7 digit
Auto 0 digit 1 digit 2 digit 3 digit 4 digit 5 digit 6 digit 7 digit
Auto - Specifythedecimal-pointpositionofthetotalizedvalueforTotalizer1.Auto:Automaticallyadjuststhenumberofdecimalplaces.0digit:Fixesthenumberofdecimalplacesto“0”.1digit:Fixesthenumberofdecimalplacesto“1”.2digit:Fixesthenumberofdecimalplacesto“2”.3digit:Fixesthenumberofdecimalplacesto“3”.4digit:Fixesthenumberofdecimalplacesto“4”.5digit:Fixesthenumberofdecimalplacesto“5”.6digit:Fixesthenumberofdecimalplacesto“6”.7digit:Fixesthenumberofdecimalplacesto“7”.
10-11 Devicerootmenu► Detailedsetup► Display► Displayformat► Displayformattotal2
Devicesetup►Detailedsetup►Displayset►Dispformat►Format total 2
RW Specifythedecimal-pointpositionofthetotalizedvalueforTotalizer2.Auto:Automaticallyadjuststhenumberofdecimalplaces.0digit:Fixesthenumberofdecimalplacesto“0”.1digit:Fixesthenumberofdecimalplacesto“1”.2digit:Fixesthenumberofdecimalplacesto“2”.3digit:Fixesthenumberofdecimalplacesto“3”.4digit:Fixesthenumberofdecimalplacesto“4”.5digit:Fixesthenumberofdecimalplacesto“5”.6digit:Fixesthenumberofdecimalplacesto“6”.7digit:Fixesthenumberofdecimalplacesto“7”.
10-12 Devicerootmenu► Detailedsetup► Display► Displayformat► Displayformattotal3
Devicesetup►Detailedsetup►Displayset►Dispformat►Format total 3
RW Specifythedecimal-pointpositionofthetotalizedvalueforTotalizer3.Auto:Automaticallyadjuststhenumberofdecimalplaces.0digit:Fixesthenumberofdecimalplacesto“0”.1digit:Fixesthenumberofdecimalplacesto“1”.2digit:Fixesthenumberofdecimalplacesto“2”.3digit:Fixesthenumberofdecimalplacesto“3”.4digit:Fixesthenumberofdecimalplacesto“4”.5digit:Fixesthenumberofdecimalplacesto“5”.6digit:Fixesthenumberofdecimalplacesto“6”.7digit:Fixesthenumberofdecimalplacesto“7”.
10-13 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display contrast
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Contrast
RW -5 -4 -3 -2 -1 0 +1 +2 +3 +4 +5
-5 -4 -3 -2 -1 0 1 2 3 4 5
0 - Specifythecontrastofthedisplay.-:Light,+:Dark
10-14 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display line
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Linemode
RW 1 Line(Big) 1 Line 2 Line 3 Line 4 Line
1 Line(Big) 1 Line 2 Line 3 Line 4 Line
3 Line - Specifythenumberoflinestobeshownonthedisplay.1Line(Big):1-linedisplaywithoutunit.Thenumericvalueisdisplayedinlargetext.1Line:1-linedisplaywithunit2Line:2-linedisplaywithunit3Line:3-linedisplaywithunit4Line:4-linedisplaywithunit
10-15 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display period
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Period
RW 0.2 s 0.4 s 1.0 s 2.0 s 4.0 s 8.0 s
0.2 s 0.4 s 1.0 s 2.0 s 4.0 s 8.0 s
0.4 s - Specifytheprocessvalueupdateperiodforthedisplay.
10-16 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display NE107
Devicesetup►Detailedsetup►Displayset►Optionalconfig►NE107 display
RW Normal NE107
Normal NE107
Normal - SpecifywhethertoshoworhideanalarmbasedonNAMUR NE107.Normal: Normal alarm displayNE107: Alarm display based on NAMUR NE107
10-17 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display alarm
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Alarm display
RW Normal Detail
Normal Detail
Normal - Specifythealarmdisplayformat.Normal:Normalalarmdisplay(Processvalueandalarm name)Detail: Detailed alarm display (Alarm name and action)
10-18 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display scroll
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Scroll mode
RW Off Manual Auto(2s) Auto(4s) Auto(8s)
Off Manual Auto(2s) Auto(4s) Auto(8s)
Manual - Specifythedisplayscrollmethod.Off:Doesnotscroll.Manual:ScrollbyinfraredswitchAuto(2s):Automaticscroll(2-secondcycle)Auto(4s):Automaticscroll(4-secondcycle)Auto(8s):Automaticscroll(8-secondcycle)
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 124
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
10-19 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display damping
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Damp
RW 0.0 to 200.0 Numberofdecimalplaces: 1
0.0 to 200.0 Numberofdecimalplaces: 1
0.0 s Specifythedampingtimeconstantofthedisplay.
10-20 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Displayformatdate
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Format date
RW MM/DD/YYYY DD/MM/YYYY YYYY/MM/DD
MM/DD/YYYY DD/MM/YYYY YYYY/MM/DD
MM/DD/YYYY - Specifythedatedisplayformat.YYYY: Year, MM: Month, DD: Day
10-21 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Language
Devicesetup►Language RW English French German Italian Spanish Portuguese Russian Chinese Japanese
English French German Italian Spanish Portuguese Russian Chinese Japanese
English - Specifythelanguagetobeusedonthedisplay.Synchronized with No. 2-1.
10-22 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Displaymeasuremode
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Display mode
RW Normal Trend
Normal Trend
Normal - Specifywhethertoexecutethetrendgraphdisplayfunction.Normal: Normal display (Displays no trend graph.)Trend: Displays a trend graph
10-23 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Trendofflinelrv
Devicesetup►Detailedsetup►Displayset►Optionalconfig►TrendofflnLRV
RW -INF(**) to +INF(**) Numberofdecimal places: 1 to 5
-999999 to +999999Numberofdecimal places: 1 to 5
0.0 - Specifythelowlimitvaluetodisplayatrendgraph.
10-24 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Trendofflineurv
Devicesetup►Detailedsetup►Displayset►Optionalconfig►TrendofflnURV
RW -INF(**) to +INF(**) Numberofdecimal places: 1 to 5
-999999 to +999999Numberofdecimal places: 1 to 5
10.0 - Specifythehighlimitvaluetodisplayatrendgraph.
10-25 Devicerootmenu► Detailedsetup► Display► Trendselect► Trend select 1
Devicesetup►Detailedsetup►Displayset►Trendselect►Trend 1
RW Flowrate(%) PV Velocity Volumeflow Massflow Calorie Analogout1 Analogout2 Totalizer1 Totalizer2 Totalizer3
Flowrate(%) PV Velocity Volumeflow Massflow Calorie Analogout1 Analogout2 Totalizer1 Totalizer2 Totalizer3
PV - Specifyitem1tobeshowninatrendgraph.
10-26 Devicerootmenu► Detailedsetup► Display► Trendselect► Trend select 2
Devicesetup►Detailedsetup►Displayset►Trendselect►Trend 2
RW None Flowrate(%) PV Velocity Volumeflow Massflow Calorie Analogout1 Analogout2 Totalizer1 Totalizer2 Totalizer3
None Flowrate(%) PV Velocity Volumeflow Massflow Calorie Analogout1 Analogout2 Totalizer1 Totalizer2 Totalizer3
None - Specifyitem2tobeshowninatrendgraph.
10-27 Devicerootmenu► Detailedsetup► Display► Trendselect► Trend select 3
Devicesetup►Detailedsetup►Displayset►Trendselect►Trend 3
RW None - Specifyitem3tobeshowninatrendgraph.
10-28 Devicerootmenu► Detailedsetup► Display► Trendselect► Trend select 4
Devicesetup►Detailedsetup►Displayset►Trendselect►Trend 4
RW None - Specifyitem4tobeshowninatrendgraph.
10-29 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display inversion
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Inversion
RW Normal Invert
Normal Invert
Normal - Specifywhethertoexecutetheblack/whiteinversefunctionofthedisplay.Normal: Normal display (Character color: Black,Backgroundcolor:White)Invert:Black/whiteinversedisplay(Charactercolor:White,Backgroundcolor:Black)
10-30 Maintenancerootmenu► Displayindication► LCD test
Devicesetup►Diag/Service►Dispindicator►LCDtest
RW Notexecute Execute Show Pattern1 Show Pattern2 Show Pattern3 Show Pattern4
Notexecute Execute Show Pattern1 Show Pattern2 Show Pattern3 Show Pattern4
Notexecute - Specifythetestdisplayfunctionofthedisplay.Notexecute:NotestdisplayExecute:Testdisplay(AllLEDON->AllLEDOFF->Hound’stoothcheck->Hound’stoothcheck(inversion)Show Pattern1: Test display (All LED ON)Show Pattern2: Test display (All LED OFF)ShowPattern3:Testdisplay(Hound’stoothcheck)ShowPattern4:Testdisplay(Hound’stoothcheck(inversion))
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 125
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
10-31 Maintenancerootmenu► Displayindication► Squawk
Devicesetup►Diag/Service►Dispindicator►Squawk
RW Off On SquawkOnce
Off On SquawkOnce
Off - Specifywhethertoexecutethedisplaysquawkfunction(backlightsquawkonthedisplay).Off:Disablesthesquawkdisplay.On:Enablesthesquawkdisplay(Continuous)SquawkOnce:Enablesthesquawkdisplay(onceonly).
10-32 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Languagepackage
Devicesetup►Detailedsetup►Displayset►Optionalconfig►Languagepackage
R Package 1Package 2
Package 1Package 2
- (*) - Indicatesthelanguagepackage.
10-33 Devicerootmenu► Detailedsetup► Display► Displayoperationconfiguration► Display installation
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►Disp install
RW No disp Withdisp
No disp Withdisp
Withdisp(*) - Specifywhetherthedisplayisprovidedornot.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 126
IM 01E22A02-02EN
(11) DeviceinformationconfigurationparametersThislistshowstheparametersrelatedtodeviceinformationsettings.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
11-1 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Tag
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►TagNo
RW ASCII 8 characters
ASCII 8 characters
All Space (*) - Specifythetagnumber.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Long tag
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►Longtag
RW ASCII 32 characters
ASCII 32 characters
All Space (*) - Specifythelongtag.
11-2 Maintenancerootmenu► Timestamp► Operation time
Devicesetup►Detailedsetup►Deviceinfo►Date/Time►Operation time
R 00000D 00: 00 to 99999D 23: 59
00000D 00: 00 to 99999D 23: 59
00000D 00: 00
- Indicatestheoperatingtimeofthedevice.
11-3 Maintenancerootmenu► Timestamp► CurrentDate
Devicesetup►Detailedsetup►Deviceinfo►Date/Time►Currentdate
R 1900/01/01to2155/12/31
1900/01/01to2155/12/31
1900/01/01 - Indicatesthecurrentdate(month,day,andyear).
11-4 Maintenancerootmenu► Timestamp► CurrentTime
Devicesetup►Detailedsetup►Deviceinfo►Date/Time►Currenttime
R 00: 00: 00 to 23: 59: 59
00: 00: 00 to 23: 59: 59
00: 00: 00 - Indicatesthecurrenttime(hour,minute,andsecond).
11-5 - Devicesetup►Detailedsetup►Deviceinfo►Date/Time►Setdate
RW 01/01/1900to12/31/2155
01/01/1900to12/31/2155
01/01/1900 - Specifythecurrentdate(month,day,andyear).
- Devicesetup►Detailedsetup►Deviceinfo►Date/Time►Settime
RW 00: 00: 00 to 23: 59: 59
00: 00: 00 to 23: 59: 59
00: 00: 00 - Specifythecurrenttime(hour,minute,andsecond).
Maintenancerootmenu► Timestamp► SetDate/Time
- RW 01/01/1900 00: 00: 00 to 12/31/215523:59: 59
01/01/1900 00: 00: 00 to 12/31/215523:59: 59
01/01/190000: 00: 00
- Specifythecurrentdate(month,day,andyear)andthecurrenttime(hour,minute,andsecond).
11-6 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Transmitter type
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Transmitter type
R Non 4A Type
Non 4A Type
- - Indicatesthetypesoftransmitterstobecombined.
11-7 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Option board ID
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Option board ID
R Non Multi
Non Multi
- - Indicatesthetypeoftheoptionboard.
11-8 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Electrode size
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►Electrode size
RW 1 mm 3 mm 8 mm 10 mm
1 mm3 mm8 mm10 mm
3 mm - Specifytheelectrodesize.
11-9 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Basic model code
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Modelcode
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifythemodelname.
11-10 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Suffixconfig1
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Suffixconfig1
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifysuffixcode1.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Suffixconfig2
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Suffixconfig2
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifysuffixcode2.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)issettotheparameteratfactoryshipping.
<5. Parameters of Magnetic Flowmeter> 127
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
11-11 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 1
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Option1
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode1.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 2
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Option2
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode2.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 3
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Option3
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode3.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Option 4
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►MScode►Option4
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode4.
11-12 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor basic model code
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Modelcode
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifythemodelname.
11-13 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remotesensorsuffixconfig1
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Suffixconfig1
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode1.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remotesensorsuffixconfig2
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Suffixconfig2
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode2.
11-14 Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 1
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Option1
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode1.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 2
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Option2
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode2.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 3
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Option3
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode3.
Devicerootmenu► Detailedsetup► Deviceinformation► Orderinformation► Remote sensor option 4
Devicesetup►Detailedsetup►Deviceinfo►Orderinfo►RSMScode►Option4
RW ASCII 16 characters
ASCII 16 characters
All Space (*) - Specifyoptionalcode4.
11-15 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Transmitter serial No
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Trans serial No
RW ASCII 16 characters
ASCII 16 characters
All Space - Specifythetransmitter’sserialnumber.
11-16 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Sensor serial No
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Sensor serial No
RW ASCII 16 characters
ASCII 16 characters
All Space - Specifythesensor’sserialnumber.
11-17 Devicerootmenu► Detailedsetup► Deviceinformation► Memo►Memo1
Devicesetup►Detailedsetup►Deviceinfo►Memo►Memo 1
RW ASCII 16 characters
ASCII 16 characters
All Space - Specifymemo1.
Devicerootmenu► Detailedsetup► Deviceinformation► Memo►Memo2
Devicesetup►Detailedsetup►Deviceinfo►Memo►Memo 2
RW ASCII 16 characters
ASCII 16 characters
All Space - Specifymemo2.
Devicerootmenu► Detailedsetup► Deviceinformation► Memo►Memo3
Devicesetup►Detailedsetup►Deviceinfo►Memo►Memo 3
RW ASCII 16 characters
ASCII 16 characters
All Space - Specifymemo3.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)issettotheparameteratfactoryshipping.
<5. Parameters of Magnetic Flowmeter> 128
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
11-18 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Main board revision
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Mainsoftrev
R R1.01.01(***) R1.01.01(***) - - Indicatesthefirmwarerevisionofthemainboard.
11-19 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Sensor board revision
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Snsrsoftrev
R R1.01.01(***) R1.01.01(***) - - Indicatesthefirmwarerevisionofthesensorboard.
11-20 Devicerootmenu► Detailedsetup► Deviceinformation► Version/Numberinformation► Indicator board revision
Devicesetup►Detailedsetup►Deviceinfo►Ver/Numinfo►Indsoftrev
R R1.01.01(***) R1.01.01(***) - - Indicatesthefirmwarerevisionofthedisplayboard.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)issettotheparameteratfactoryshipping.
<5. Parameters of Magnetic Flowmeter> 129
IM 01E22A02-02EN
(12) DiagnosisfunctionconfigurationparametersThislistshowstheparametersrelatedtotheelectrodeadhesiondetection,flownoisediagnosis,andverificationfunctionsettings.
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
12-1 Diagnosticrootmenu► Diagnosis► Adhesion► Adhesionfunction
Devicesetup►Diag/Service►Diagnosis►Adhesion►Function
RW Disable Enable
Disable Enable
Enable - Specifywhethertoenableordisabletheelectrodeadhesiondetectingfunction.
12-2 Diagnosticrootmenu► Diagnosis► Adhesion► Adhesion level 1
Devicesetup►Diag/Service►Diagnosis►Adhesion►Threshold level 1
RW 0.00 to +100.00 Numberofdecimalplaces: 2
0.00 to +100.00Numberofdecimalplaces: 2
0.10 M ohm Specifythelevel1valueusedtojudgetheelectrode adhesion detection.
12-3 Diagnosticrootmenu► Diagnosis► Adhesion► Adhesion level 2
Devicesetup►Diag/Service►Diagnosis►Adhesion►Threshold level 2
RW 0.00 to +100.00 Numberofdecimalplaces: 2
0.00 to +100.00Numberofdecimalplaces: 2
0.50 M ohm Specifythelevel2valueusedtojudgetheelectrode adhesion detection.
12-4 Diagnosticrootmenu► Diagnosis► Adhesion► Adhesion level 3
Devicesetup►Diag/Service►Diagnosis►Adhesion►Threshold level 3
RW 0.00 to +100.00 Numberofdecimalplaces: 2
0.00 to +100.00Numberofdecimalplaces: 2
4.00 M ohm Specifythelevel3valueusedtojudgetheelectrode adhesion detection.
12-5 Diagnosticrootmenu► Diagnosis► Adhesion► Adhesion level 4
Devicesetup►Diag/Service►Diagnosis►Adhesion►Threshold level 4
RW 0.00 to +100.00 Numberofdecimalplaces: 2
0.00 to +100.00Numberofdecimalplaces: 2
12.00 M ohm Specifythelevel4valueusedtojudgetheelectrode adhesion detection.
12-6 Diagnosticrootmenu► Diagnosis► Adhesion► Result► Adhesionvalue
Devicesetup►Diag/Service►Diagnosis►Adhesion►Result►Value
R 0.00000 to +1000.0 Numberofdecimal places: 0 to 5
0.00000 to +1000.0Numberofdecimal places: 0 to 5
- M ohm Indicatestheresistancevalueusedtojudgetheelectrode adhesion detection.
12-7 Diagnosticrootmenu► Diagnosis► Adhesion► Result► Adhesionstatus
Devicesetup►Diag/Service►Diagnosis►Adhesion►Result►Status
R Level0 Level1 Level2 Level3 Level4
Level0 Level1 Level2 Level3 Level4
- - Indicates the electrode adhesion detection level.
12-8 Diagnosticrootmenu► Diagnosis► Adhesion► Adhesion check cycle
Devicesetup►Diag/Service►Diagnosis►Adhesion►Checkcycle
RW 0.5 min 1 min 2 min 10 min
0.5 min1 min2 min10 min
2 min - Specifytheupdatecycleforelectrodeadhesiondetection.
12-9 Diagnosticrootmenu► Diagnosis► Flownoise► Flownoisefunction
Devicesetup►Diag/Service►Diagnosis►Flownoise►Function
RW Disable Enable
Disable Enable
Disable - Specifywhethertoenableordisabletheflownoisediagnosisfunction.
12-10 Diagnosticrootmenu► Diagnosis► Flownoise► Flow noise level 1
Devicesetup►Diag/Service►Diagnosis►Flownoise►Threshold level 1
RW 0.0to+999.9 Numberofdecimal places: 1
0.0to+999.9Numberofdecimal places: 1
5.0 cm/s Specifythelevel1valueusedtojudgetheflownoise.
12-11 Diagnosticrootmenu► Diagnosis► Flownoise► Flow noise level 2
Devicesetup►Diag/Service►Diagnosis►Flownoise►Threshold level 2
RW 0.0to+999.9 Numberofdecimal places: 1
0.0to+999.9Numberofdecimal places: 1
10.0 cm/s Specifythelevel2valueusedtojudgetheflownoise.
12-12 Diagnosticrootmenu► Diagnosis► Flownoise► Flow noise level 3
Devicesetup►Diag/Service►Diagnosis►Flownoise►Threshold level 3
RW 0.0to+999.9 Numberofdecimal places: 1
0.0to+999.9Numberofdecimal places: 1
30.0 cm/s Specifythelevel3valueusedtojudgetheflownoise.
12-13 Diagnosticrootmenu► Diagnosis► Flownoise► Flow noise level 4
Devicesetup►Diag/Service►Diagnosis►Flownoise►Threshold level 4
RW 0.0to+999.9 Numberofdecimal places: 1
0.0to+999.9Numberofdecimal places: 1
400.0 cm/s Specifythelevel4valueusedtojudgetheflownoise.
12-14 Diagnosticrootmenu►Diagnosis►Flownoise►Result►Flownoise
Devicesetup►Diag/Service►Diagnosis►Flownoise►Result►Value
R 0.00000 to +100.00 Numberofdecimal places: 0 to 5
0.00000 to +100.00Numberofdecimal places: 0 to 5
- cm/s Indicatestheflownoisediagnosisresult.
12-15 Diagnosticrootmenu► Diagnosis► Flownoise►Result► Flownoisestatus
Devicesetup►Diag/Service►Diagnosis►Flownoise►Result►Status
R Level0 Level1 Level2 Level3 Level4
Level0 Level1 Level2 Level3 Level4
- - Indicatestheleveloftheflownoisediagnosisresult.
12-16 Diagnosticrootmenu► Diagnosis► Flownoise► Flow noise damping
Devicesetup►Diag/Service►Diagnosis►Flownoise►Damp
RW 0.1 to 500.0 Numberofdecimal places: 1
0.1 to 500.0Numberofdecimal places: 1
3.0 s Specifythedampingtimeconstantoftheflownoise.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 130
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
12-17 Diagnosticrootmenu► Diagnosis► Flownoise► Flow noise span
Devicesetup►Diag/Service►Diagnosis►Flownoise►Span
RW 0.1 to 999.9 Numberofdecimal places: 1
0.1 to 999.9Numberofdecimal places: 1
150.0 cm/s Specifythespanoftheflownoise.
12-18 Diagnosticrootmenu► Diagnosis► Conductivity► Lowconductivityfunction
Devicesetup►Diag/Service►Diagnosis►Conductivity►Function
RW Disable Enable
Disable Enable
Disable - Specifywhethertoenableordisablethelowconductivitydiagnosisfunction.
12-19 Diagnosticrootmenu► Diagnosis► Conductivity► Result► Conductivityvalue
Devicesetup►Diag/Service►Diagnosis►Conductivity►Result►Value
R 0.00000 to +INF(**) Numberofdecimal places: 0 to 5
0.00000 to 999999Numberofdecimal places: 0 to 5
- mS/cm Indicatestheconductivity.
12-20 Diagnosticrootmenu► Diagnosis► Conductivity► Conductivitylowlimit
Devicesetup►Diag/Service►Diagnosis►Conductivity►Lowlimit
RW 0.0000 to 99.9999 Numberofdecimal places: 4
0.0000 to 99.9999Numberofdecimal places: 4
0.0010 mS/cm Specifythevalueusedtojudgethelowconductivity.
12-21 Diagnosticrootmenu► Diagnosis► Diagnostic Exe
Devicesetup►Diag/Service►Diagnosis►Diagnosticexecute
RW Notexecute Elec ins exe Conn chk exe
Notexecute Elec ins exe Conn chk exe
Notexecute - Specifywhethertoexecutetheelectrodeinsulationdeteriorationdiagnosisfunctionandthemisconnectiondetectingfunction.Notexecute:Doesnotexecutethefunctions.Elecinsexe:Executestheelectrodeinsulationdeteriorationdiagnosisfunction.Connchkexe:Executesthemisconnectiondetectingfunction.
12-22 Diagnosticrootmenu► Diagnosis► Coilinsulationthreshold
Devicesetup►Diag/Service►Diagnosis►Coilinsulthreshold
RW 0.0 to 100.0 Numberofdecimal places: 1
0.0 to 100.0Numberofdecimal places: 1
25.0 % Specifythevalueusedtojudgethedeteriorationofcoilinsulation.
12-23 Diagnosticrootmenu► Diagnosis► IEXcompare
Devicesetup►Diag/Service►Diagnosis►IEXcompare
R 0.0 to 999.9 Numberofdecimal places: 1
0.0 to 999.9Numberofdecimal places: 1
260.0 mA Indicatesthereferenceexcitationcurrentvalueusedtojudgethedeteriorationofcoilinsulation.
12-24 Diagnosticrootmenu► Diagnosis► Vpeakholdvalue
Devicesetup►Diag/Service►Diagnosis►V peak hold
R 0.000 to 3.000 Numberofdecimal places: 3
0.000 to 3.000Numberofdecimal places: 3
- V Indicatesthemaximumamplitudeoftheexcitationsignal.
12-25 Diagnosticrootmenu► Diagnosis► IEXcoilresistance
Devicesetup►Diag/Service►Diagnosis►IEXresistance
R 0to+9999.9 Numberofdecimal places: 1
0to+9999.9Numberofdecimal places: 1
- ohm Indicatesthecoilresistancevaluewhentheexcitationcurrentisapplied.
12-26 Diagnosticrootmenu► Diagnosis►Empty► Electrode voltage A
Devicesetup►Diag/Service►Diagnosis►Emptycheck►Electrode voltage A
R -3.00 to 3.00 Numberofdecimalplaces: 2
-3.00 to 3.00Numberofdecimalplaces: 2
- V Indicates the voltage between electrode A and electrode C.
12-27 Diagnosticrootmenu► Diagnosis►Empty► Electrode voltage B
Devicesetup►Diag/Service►Diagnosis►Emptycheck►Electrode voltage B
R -3.00to+3.00 Numberofdecimalplaces: 2
-3.00to+3.00Numberofdecimalplaces: 2
- V Indicates the voltage between electrode B and electrode C.
12-28 Diagnosticrootmenu► Diagnosis►Empty► Result►Emptystatus
Devicesetup►Diag/Service►Diagnosis►Emptycheck►Emptystatus
R Full Empty
Full Empty
- - Indicatestheresultofthesensoremptypipestatefunction.
12-29 Maintenancerootmenu► Verification► Diagnosticoutput
Devicesetup►Diag/Service►Diagnosis►Diagnosticoutput
RW Zero Measuredvalue Hold
Zero Measuredvalue Hold
Zero - Specifytheoutputtousetheverificationfunction.
12-30 Maintenancerootmenu► Verification► VF mode
Devicesetup►Diag/Service►Verification►Mode
RW Noflow Flow
Noflow Flow
Noflow - Specifythefluidstatustowhichtheverificationfunctionistobeapplied.Noflow:Nofluidflows.Flow:Fluidflows.
12-31 Maintenancerootmenu► Verification► VerificationExe
Devicesetup►Diag/Service►Verification►Execute
RW Notexecute Execute
Notexecute Execute
Notexecute - Specifywhethertoexecutetheverificationfunction.
12-32 Maintenancerootmenu► Verification►VFNo
Devicesetup►Diag/Service►Verification►VF No
RW Factory Previous Present
Factory Previous Present
Factory - Specifythetimingtodisplaythediagnosisresultoftheverificationfunction.
12-33 Maintenancerootmenu► Verification► Result► VFcheckresult
Devicesetup►Diag/Service►Verification►Result►Failed/Passed
R Passed Failed Canceled No Data Unknown
Passed Failed Canceled No Data Unknown
No Data - Indicatestheresultofexecutingtheverificationfunction.
12-34 Maintenancerootmenu► Verification► Result► VF operation time
Devicesetup►Diag/Service►Verification►Result►VFoperatetime
R 00000D 00: 00 to 99999D 23: 59
00000D 00: 00 to 99999D 23: 59
00000D 00: 00 - Indicatestheoperatingtimeoftheverificationfunction.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 131
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
12-35 Maintenancerootmenu► Verification► Result► Magneticcircuitresult
Devicesetup►Diag/Service►Verification►Result►Magneticcircuit
R Passed Failed Canceled No Data Unknown
Passed Failed Canceled No Data Unknown
No Data - Indicatestheresultofexecutingtheverificationfunction(thediagnosisresultofthemagneticcircuit).
12-36 Maintenancerootmenu► Verification► Result► Excitationcircuitresult
Devicesetup►Diag/Service►Verification►Result►Excitecircuit
R Passed Failed Canceled No Data Unknown
Passed Failed Canceled No Data Unknown
No Data - Indicatestheresultofexecutingtheverificationfunction(thediagnosisresultoftheexcitationcircuit).
12-37 Maintenancerootmenu► Verification► Result► Calculationcircuitresult
Devicesetup►Diag/Service►Verification►Result►Calccircuit
R Passed Failed Canceled No Data Unknown
Passed Failed Canceled No Data Unknown
No Data - Indicatestheresultofexecutingtheverificationfunction(thediagnosisresultofthecalculationcircuit).
12-38 Maintenancerootmenu► Verification► Result► VFdevicestatusresult
Devicesetup►Diag/Service►Verification►Result►Devicestatus
R Passed Failed Canceled No Data Unknown
Passed Failed Canceled No Data Unknown
No Data - Indicatestheresultofexecutingtheverificationfunction(thediagnosisresultofthedevicealarm).
12-39 Maintenancerootmenu► Verification► Result► Connectionstatusresult
Devicesetup►Diag/Service►Verification►Result►Connectstatus
R Passed Failed Canceled No Data Unknown
Passed Failed Canceled No Data Unknown
No Data - Indicatestheresultofexecutingtheverificationfunction(wiringmisconnectioncheckresult).
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 132
IM 01E22A02-02EN
(13) TestmodeconfigurationparametersThis list shows the parameters related to the test mode setting.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
13-1 Maintenancerootmenu►Test► Release time
Devicesetup►Diag/Service►Test►Release time
RW 10 min 30 min 1 h 3 h 12 h
10 min 30 min 1 h 3 h 12 h
10 min - Specifythetimetoautomaticallyresetthetestmode.
13-2 Maintenancerootmenu►Test► Test mode
- RW Velocity test on Volumeflowtest on Massflowteston Calorificvaluetest on AO1 test on Pulse1teston SO1 test on AO2 test on Pulse2teston SO2 test on AI test on SO3 test on SI3 test on
Velocity test on Volumeflowtest on Massflowteston Calorificvaluetest on AO1 test on Pulse1teston SO1 test on AO2 test on Pulse2teston SO2 test on AI test on SO3 test on SI3 test on
All Space - Specifywhethertosetthetestmodeonoroff.
- Devicesetup►Diag/Service►Test►Inputtest►Testmode
RW Velocity test Volumetest Mass test Calorie test AI test SI3 test
Velocity test Volumetest Mass test Calorie test AI test SI3 test
- - Specifywhethertosetthetestmode(input)onoff.
- Devicesetup►Diag/Service►Test►Outputtest►Testmode
RW AO1 test PO1 test SO1 test AO2 test PO2 test SO2 test SO3 test
AO1 test PO1 test SO1 test AO2 test PO2 test SO2 test SO3 test
- - Specifywhethertosetthetestmode(output)onoroff.
13-3 Maintenancerootmenu►Test► Inputtest►Velocity
Devicesetup►Diag/Service►Test►Inputtest►Velocity
RW -INF(**) to +INF(**) Numberofdecimal places: 0 to 5
-999999 to +999999 Numberofdecimal places: 0 to 5
0.0 Specifiedin No.3-15
Specifythetestvalueoftheflowvelocity.
13-3 Maintenancerootmenu►Test► Inputtest► Volumeflow
Devicesetup►Diag/Service►Test►Inputtest►Volume
RW -INF(**) to +INF(**) Numberofdecimal places: 0 to 5
-999999 to +999999 Numberofdecimal places: 0 to 5
0.0 Specifiedin No.3-16/No.3-19
Specifythetestvalueofthevolumetricflowrate.
13-4 Maintenancerootmenu►Test► Inputtest►Massflow
Devicesetup►Diag/Service►Test►Inputtest►Mass
RW -INF(**) to +INF(**) Numberofdecimal places: 0 to 5
-999999 to +999999 Numberofdecimal places: 0 to 5
0.0 Specifiedin No.3-17/No.3-19
Specifythetestvalueofthemassflowrate.
13-5 Maintenancerootmenu►Test► Inputtest► Calorificvalue
Devicesetup►Diag/Service►Test►Inputtest►Calorie
RW -INF(**) to +INF(**) Numberofdecimal places: 0 to 5
-999999 to +999999 Numberofdecimal places: 0 to 5
0.0 Specifiedin No.3-18/No.3-19
Specifythetestvalueofthecalorie.
13-6 Maintenancerootmenu►Test► Outputtest►AO1
Devicesetup►Diag/Service►Test►Outputtest►AO1
RW 2.400 to 21.600 Numberofdecimal places: 3
2.400 to 21.600 Numberofdecimal places: 3
4.000 mA SpecifythetestvalueofthecurrentoutputfortheI/O1terminal.
13-7 Maintenancerootmenu►Test► Outputtest►Pulse1
Devicesetup►Diag/Service►Test►Outputtest►PO1
RW 0 to 12500 Numberofdecimal places: 0
0 to 12500 Numberofdecimal places: 0
0.0 pps(pulse/s) SpecifythetestvalueofthepulseoutputfortheI/O2terminal.
13-8 Maintenancerootmenu►Test► Outputtest►SO1
Devicesetup►Diag/Service►Test►Outputtest►SO1
RW Open Close
Open Close
Open - SpecifythetestvalueofthestatusoutputfortheI/O2 terminal.
13-9 Maintenancerootmenu►Test► Outputtest►AO2
Devicesetup►Diag/Service►Test►Outputtest►AO2
RW 2.400 to 21.600 Numberofdecimal places: 3
2.400 to 21.600 Numberofdecimal places: 3
4.000 mA SpecifythetestvalueofthecurrentoutputfortheI/O3orI/O4terminal.
13-10 Maintenancerootmenu►Test► Outputtest►Pulse2
Devicesetup►Diag/Service►Test►Outputtest►PO2
RW 0 to 12500 Numberofdecimal places: 0
0 to 12500 Numberofdecimal places: 0
0 pps(pulse/s) SpecifythetestvalueofthepulseoutputfortheI/O3orI/O4terminal.
13-11 Maintenancerootmenu►Test► Outputtest►SO2
Devicesetup►Diag/Service►Test►Outputtest►SO2
RW Open Close
Open Close
Open - SpecifythetestvalueofthestatusoutputfortheI/O3orI/O4terminal.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 133
IM 01E22A02-02EN
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
13-12 Maintenancerootmenu►Test► Inputtest►AI
Devicesetup►Diag/Service►Test►Inputtest►AI
RW 0.000 to 21.600 Numberofdecimal places: 3
0.000 to 21.600 Numberofdecimal places: 3
0.000 mA SpecifythetestvalueofthecurrentinputfortheI/O4 terminal.
13-13 Maintenancerootmenu►Test► Outputtest►SO3
Devicesetup►Diag/Service►Test►Outputtest►SO3
RW Open Close
Open Close
Open - SpecifythetestvalueofthestatusoutputfortheI/O3orI/O4terminal.
13-14 Maintenancerootmenu►Test► Inputtest►SI3
Devicesetup►Diag/Service►Test►Inputtest►SI3
RW Open Short
Open Close
Open - SpecifythetestvalueofthestatusinputfortheI/O3terminal.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 134
IM 01E22A02-02EN
(14) Backup,restore,anddatalogconfigurationparametersThislistshowstheparametersrelatedtotheparameterbackupfunction,restorefunction,anddataloggingfunction.
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
14-1 Maintenancerootmenu► Parambkup/restore► Factorybackupname
Devicesetup►Diag/Service►Parambkup/restore►Fbackupname
R ASCII 16 characters ASCII 16 characters Factory Delivery
- Indicatesthenameofthefilethatisbackedup(forfactory).
14-2 Maintenancerootmenu► Parambkup/restore► Factorybackupdate
Devicesetup►Diag/Service►Parambkup/restore►Fbackupdate
R ASCII 16 characters ASCII 16 characters 06/30/2017(***) - Indicatesthedatewhenbackuphasbeenmade(forfactory).
14-3 Maintenancerootmenu► Parambkup/restore► SDbackupname
Devicesetup►Diag/Service►Parambkup/restore►SDbackupname
RW ASCII 8 characters ASCII 8 characters SD_FILE - SpecifythenameofthefiletobebackedupontoamicroSDcardorrestoredfromamicroSD card.
14-4 Maintenancerootmenu► Parambkup/restore► Backupname1
Devicesetup►Diag/Service►Parambkup/restore►Backupname1
RW ASCII 16 characters ASCII 16 characters Backup1 - Specifythenameofthefiletobebackedup(1foruser).
14-5 Maintenancerootmenu► Parambkup/restore► Backupdate1
Devicesetup►Diag/Service►Parambkup/restore►Backupdate1
RW ASCII 16 characters ASCII 16 characters 01/01/2016 - Specifythedatewhenbackuphasbeenmade(1foruser).
14-6 Maintenancerootmenu► Parambkup/restore► Backupname2
Devicesetup►Diag/Service►Parambkup/restore►Backupname2
RW ASCII 16 characters ASCII 16 characters Backup2 - Specifythenameofthefiletobebackedup(2foruser).
14-7 Maintenancerootmenu► Parambkup/restore► Backupdate2
Devicesetup►Diag/Service►Parambkup/restore►Backupdate2
RW ASCII 16 characters ASCII 16 characters 01/01/2016 - Specifythedatewhenbackuphasbeenmade(2foruser).
14-8 Maintenancerootmenu► Parambkup/restore► Backupname3
Devicesetup►Diag/Service►Parambkup/restore►Backupname3
RW ASCII 16 characters ASCII 16 characters Backup3 - Specifythenameofthefiletobebackedup(3foruser).
14-9 Maintenancerootmenu► Parambkup/restore► Backupdate3
Devicesetup►Diag/Service►Parambkup/restore►Backupdate3
RW ASCII 16 characters ASCII 16 characters 01/01/2016 - Specifythedatewhenbackuphasbeenmade(3foruser).
14-10 Maintenancerootmenu► Parambkup/restore► BackupExe
Devicesetup►Diag/Service►Parambkup/restore►Backupexecute
RW NotexecuteStore Main to 1Store Main to 2Store Main to 3Store Main to SDStore EEP1 to SDStore EEP2 to SDStore EEP3 to SD
NotexecuteStore Main to 1Store Main to 2Store Main to 3Store Main to SDStore EEP1 to SDStore EEP2 to SDStore EEP3 to SD
Notexecute - Specifywhethertoexecutethebackupfunctionaswellasthebackuplocation.Notexecute:NobackupStoremainto1:Makesabackupfromthemainboardoftheinstrumentto memory 1 on the display board.Storemainto2:Makesabackupfromthemainboardoftheinstrumenttomemory2onthedisplay board.Storemainto3:Makesabackupfromthemainboardoftheinsturmenttomemory3onthedisplay board.StoremaintoSD:MakesabackupfromthemainboardoftheinstrumenttoamicroSDcard.StoreEEP1toSD:Makesabackupfrommemory 1 on the display board onto a microSD card.StoreEEP2toSD:Makesabackupfrommemory 2 on the display board onto a microSD card.StoreEEP3toSD:Makesabackupfrommemory 3 on the display board onto a microSD card.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)issettotheparameteratfactoryshipping.
<5. Parameters of Magnetic Flowmeter> 135
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
14-11 Maintenancerootmenu► Parambkup/restore► Restore Exe
Devicesetup►Diag/Service►Parambkup/restore►Restoreexecute
RW NotexecuteDuplicateData1DuplicateData2DuplicateData3DuplicateSDRestore Data 1Restore Data 2Restore Data 3Restore SDCompulsionData1CompulsionData2CompulsionData3CompulsionSDRestore Factory
NotexecuteDuplicateData1DuplicateData2DuplicateData3DuplicateSDRestore Data 1Restore Data 2Restore Data 3Restore SDCompulsionData1CompulsionData2CompulsionData3CompulsionSDRestore Factory
Notexecute - Specifywhethertoexecutetherestorefunction,the restoration location, and data to be restored.Notexecute:Doesnotrestoredata.DuplicateData1:RestoresDuplicateDatafrommemory 1 on the indicator board to the main boardoftheinstrument.DuplicateData2:RestoresDuplicateDatafrommemory 2 on the display board to the main boardoftheinstrument.DuplicateData3:RestoresDuplicateDatafrommemory 3 on the display board to the main boardoftheinstrument.DuplicateSD:RestoresDuplicateDatafromamicroSDcardtothemainboardoftheinstrument.RestoreData1:RestoresRestoreDatafrommemory 1 on the display board to the main boardoftheinstrument.RestoreData2:RestoresRestoreDatafrommemory 2 on the display board to the main boardoftheinsturment.RestoreData3:RestoresRestoreDatafrommemory 3 on the display board to the main boardoftheinsturment.RestoreSD:RestoresRestoreDatafromamicroSDcardtothemainboardoftheinsturment.CompulsionData1:RestoresCompulsionDatafrommemory1onthedisplayboardtothemainboardoftheinstrument.CompulsionData2:RestoresCompulsionDatafrommemory2onthedisplayboardtothemainboardoftheinsturment.CompulsionData3:RestoresCompulsionDatafrommemory3onthedisplayboardtothemainboardoftheinstrument.CompulsionSD:RestoresCompulsionDatafromamicroSDcardtothemainboardoftheinsturment.RestoreFactory:Restorestothestatusthatissetuponshipmentfromthemanufacturingplant.
14-12 Devicesetup►Diag/Service►Parambkup/restore►Restoreresult
R Unexecuted Success Failure Running
Unexecuted Success Failure Running
Unexecuted - Indicatestheresultofexecutingtherestorefunction.Unexecuted:Doesnotrestoredata.Success:Succeededinrestoration.Failure:Failedinrestoration.Running:Parameterrestorerunning
14-13 Maintenancerootmenu► Datalogging►File name
Devicesetup►Diag/Service►Datalog►Filename
RW ASCII 8 characters ASCII 8 characters LOG_FILE - Specifythenameofthefiletobestoredbydatalog.
14-14 Maintenancerootmenu► Datalogging►Interval time
Devicesetup►Diag/Service►Datalog►Intervaltime
RW 1 s 10 s 30 s 1 min 5 min 30 min 1 h
1 s10 s30 s1 min5 min30 min1 h
1 min - Specifythedatalogstorageinterval.
14-15 Maintenancerootmenu► Datalogging►Start date
Devicesetup►Diag/Service►Datalog►Startdate
R 2016/01/01to2155/12/31
2016/01/01to2155/12/31
- - Indicates the date to start the data logging function.
14-16 Maintenancerootmenu► Datalogging►Start time
Devicesetup►Diag/Service►Datalog►Starttime
R 00: 00: 00 to 23: 59: 59
00: 00: 00 to 23: 59: 59
- - Indicates the time to start the data logging function.
14-17 Maintenancerootmenu► Datalogging►End time
Devicesetup►Diag/Service►Datalog►Endtime
RW 10 min 30 min 1 h 3 h 12 h 24 h 72 h 240 h
10 min30 min1 h3 h12 h24 h72 h240 h
12 h - Specifythetimetoendthedataloggingfunction.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)issettotheparameteratfactoryshipping.
<5. Parameters of Magnetic Flowmeter> 136
IM 01E22A02-02EN
No.Name
SettingRange
Default value Unit DescriptionHART communication Display HART communication Display
14-18 Maintenancerootmenu►Datalogging►Log1 select
Devicesetup►Diag/Service►Datalog►Log1
RW Velocity Volumeflow Massflow Calorie PV Flow noise Adhesion Electrode A Electrode B V peak
Velocity Volumeflow Massflow Calorie PV Flow noise Adhesion Electrode A Electrode B V peak
PV - Specifyprocessvalue1tobestoredbydatalog.
14-19 Maintenancerootmenu►Datalogging►Log2 select
Devicesetup►Diag/Service►Datalog►Log2
RW Velocity - Specifyprocessvalue2tobestoredbydatalog.
14-20 Maintenancerootmenu►Datalogging►Log3 select
Devicesetup►Diag/Service►Datalog►Log3
RW Volumeflow - Specifyprocessvalue3tobestoredbydatalog.
14-21 Maintenancerootmenu►Datalogging►Log4 select
Devicesetup►Diag/Service►Datalog►Log4
RW Massflow - Specifyprocessvalue4tobestoredbydatalog.
14-22 Maintenancerootmenu►Datalogging►Logging Exe
Devicesetup►Diag/Service►Datalog►Execute
RW Notexecute Execute
Notexecute Execute
Notexecute - Specifywhethertoexecutethedataloggingfunction.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).(***)issettotheparameteratfactoryshipping.
<5. Parameters of Magnetic Flowmeter> 137
IM 01E22A02-02EN
(15) Parameter protection parametersThislistshowstheparametersrelatedtothewriteprotectionfunction.
No.Name
SettingRange Default
value Unit DescriptionHART communication Display HART communication Display
15-1 - Devicesetup►Detailedsetup►Protection►Keycode
RW 0000 to 9999 Numberofdecimal places: 0
0000 to 9999Numberofdecimal places: 0
0000 - Display-limitedparameter(forservice)
15-2 Devicerootmenu►Detailedsetup►Protection► Writeprotect
Devicesetup►Detailedsetup►Protection►Writeprotectsts
R No Yes
No Yes
No - Indicateswhethertousethewriteprotectionfunction.
15-3 Devicerootmenu►Detailedsetup► Protection► Enable write 10 min
Devicesetup►Detailedsetup►Protection►Enablewrite
RW ASCII 8 characters
ASCII 8 characters
All Space - Enter the password to cancel the write protection functionfor10minutes.
15-4 Devicerootmenu►Detailedsetup► Protection► New password
Devicesetup►Detailedsetup►Protection►Newpassword
RW ASCII 8 characters
ASCII 8 characters
All Space - Specifyanewpasswordtousethewriteprotectionfunction.
15-5 Devicerootmenu►Detailedsetup► Protection► Softwareseal
Devicesetup►Detailedsetup►Protection►Softsealstatus
R Keep Break
Keep Break
Keep - IndicateswhethertousetheJokerpassword.
(*)indicatesaparameterwhichhasalreadyspecifiedbyorderinginformationandinformationofasensortobecombined.(**)istherangeofsingleprecisionfloatingpoint(IEEE754).
<5. Parameters of Magnetic Flowmeter> 138
IM 01E22A02-02EN
5.2 Menu Tree of DisplayOperation level
Device setupDevice setupCurrent alarmLanguage
Current alarmSetting uploadStatus 0 Status 1Status 2Status 3Status 4Status 5Status 14Status 15Status 16Status 17Status 18Status 19Status 20Setting download
Process variables
Diag/Service
Process variablesFlow rate(%)Flow rateVelocityVolumeMassCalorieAnalog out 1Analog out 2Totalizer
Diag/ServiceSts/Self test
Time stamp
TotalizerTotalizer 1Totalizer 2Totalizer 3Totalizer 1 countTotalizer 2 countTotalizer 3 count
Alarm record maskMask 1-1Mask 1-2Mask 2-1Mask 2-2Mask 3-1
Sts/Self testCurrent alarm
Current alarm
Alarm
Status 0Status 1Status 2Status 3Status 4Status 5Status 14Status 15Status 16Status 17Status 18Status 19Status 20
Alarm recordRecord alarm 1Record time 1Record alarm 2Record time 2Record alarm 3Record time 3Record alarm 4Record time 4
Time stampDateTimeOp time
Alarm out maskMask 1-1Mask 1-2Mask 2-1Mask 2-2Mask 3-1Mask 3-2Mask 4-1
Alarm
M
Alarm record mask
Alarm record
Alarm out mask
Exit OperatorMaintenanceSpecialist
F0501.ai
<5. Parameters of Magnetic Flowmeter> 139
IM 01E22A02-02EN
Verification
Autozero
AO/AI trim
H/L alarm cfg
Test
Test
VerificationModeExecute VF No Result
Operation levelExit Operator MaintenanceSpecialist
Device setup
Release time Input test
Output test Output test Test mode
AO1 PO1SO1 AO2 PO2 SO2 SO3
Result Value Status
Result ValueStatus
ConductivityFunction Low limit Result
Empty checkElectrode voltage A Electrode voltage B Empty status
Diagnosis
Result Value
Diagnosis Adhesion
Adhesion
Flow noise
Function
Conductivity
Threshold level 1
Diagnostic execute
Threshold level 2
Coil insul threshold
Threshold level 3
IEX compare
Threshold level 4
Diagnostic output
Result
V peak hold
Check cycle
IEX resistance Empty check
Flow noiseFunction Threshold level 1 Threshold level 2 Threshold level 3 Threshold level 4 Result Damp Span
Result Failed/Passed VF operate timeMagnetic circuitExcite circuit Calc circuit Device status Connect status
Autozero ExecuteResult
Result Zero value
AO/AI trim AO trim
AO trim
AI trim
AO1 trim clearAO1 trim 4mAAO1 trim 20mAAO2 trim clearAO2 trim 4mAAO2 trim 20mA
AI trimTrim clear Trim 4mATrim 20mAH/L alarm cfg
High alarm
Input test
Low alarm
Test mode
HH alarm
Velocity
LL alarm
Volume
H/L alarm hyst
Mass
4-20 burnout
Calorie AI SI3
Device setup (Continued)
Diag/Service (Continued)
F0502.ai
<5. Parameters of Magnetic Flowmeter> 140
IM 01E22A02-02EN
Pro var
Density Value select Unit Fixed density Std density Correct density
Calorie Damp AO/FDamp pls/ttl Unit Time unit SpanSpecific heat
MassDamp AO/F Damp pls/ttl Unit Time unit Span
Volume Damp AO/FDamp pls/ttl Unit Time unit Span
Velocity Damp AO/F Damp pls/ttl Unit Span
Param bkup/restore F backup name F backup dateSD backup name Backup execute Restore executeRestore result Backup name 1 Backup date 1 Backup name 2Backup date 2Backup name 3 Backup date 3
Data log File name Interval time Start dateStart time End timeExecuteLog 1 Log 2 Log 3 Log 4
Disp indicatorLCD test Squawk
Volume Setting uploadDamp AO/FDamp pls/ttlUnit Time unitSpan Setting download
Pulse/Status out Setting upload P1 unitP1 val F1 at 0% F1 at 100%Setting download
Display setSetting uploadLine 1 Line 2Line 3Setting download
Pro varPV flow select Velocity
Density
Calorie
Mass
Volume
Data log
Disp indicator
Operation level ExitOperatorMaintenance Specialist
Device setup
Param bkup/restore
Device setup (Continued)
Diag/Service (Continued)
Easy setup wizard Volume
Pulse/Status out
Display set Autozero exe
Detailed setup
F0503.ai
Easy setup wizard
Detailed setup
<5. Parameters of Magnetic Flowmeter> 141
IM 01E22A02-02EN
SO3 Active modeFunction
PO2/SO2 Active pulse Output mode Pulse select Active modeFix width Rate unit Rate value Low cut Alarm out Frequency at 0% Frequency at 100%SO2 function
PO1/SO1Output mode Active mode Fix width Rate unit Rate value Low cut Alarm out Frequency at 0%Frequency at 100% SO1 function
Totalizer 3 Unit Conv factor Low cut Failure optsOptions Start/Stop Reset/Preset Preset valueSet point
Totalizer 2 Unit Conv factor Low cut Failure optsOptions Start/Stop Reset/Preset Preset value Set point
Totalizer 1 Unit Conv factor Low cut Failure opts OptionsStart/Stop Reset/Preset Preset value Set point
User span AO2Select Span Unit
User span AO1 Select Span Unit
TemperatureStd temperatureMeas temperatureFixed temperatureCoef A1 Coef A2
SensorLow MFHigh MF Flow sensor sel Nominal size unitNominal size
User SpanUser span AO1
User span AO2
Totalizer Totalizer 1
Totalizer 2
Totalizer 3
Pulse/Status out PO1/SO1
PO2/SO2
SO3
TemperatureVelocity check
Sensor
User Span
Totalizer
Pulse/Status out
Operation level Exit Operator Maintenance Specialist
Device setup Device setup (Continued)
Detailed setup (Continued)
Pro var (Continued)
F0504.ai
<5. Parameters of Magnetic Flowmeter> 142
IM 01E22A02-02EN
AI Function High limit Low limit Value Unit URV LRV
AO2 AO2 Select Low cut High limit Low limit Alarm out
AO1 Low cut High limit Low limit Alarm out Range mode
SI3 Active modeFunction State
Date/Time Current date Current time Operation time Set date Set time
Optional config Contrast Line mode Period NE107 display Alarm display Scroll modeDampFormat dateInversionLanguage packageDisplay modeTrend offln LRVTrend offln URV
Disp format Format PV Format total 1 Format total 2 Format total 3
Trend select Trend 1 Trend 2 Trend 3 Trend 4
Line select Line 1 Line 2 Line 3 Line 4 Line 5Line 6 Line 7 Line 8
Status inSI3
Analog out/in AO1
AO2
AI
Multi range Forward span 2 Reverse span 1 Reverse span 2Auto range hyst Bi direction hyst
Access cfg User roleChg mainte Chg special
AUX calculation Flow directRate limit Dead time Noise filterPulsing flow Power sync on/offSet power freq Iex power frequencyMeas power freqSet SIL
Display setLine select
Trend select
Disp format
Optional config
Device info Date/Time
Status in
Analog out/in
Multi range
AUX calculation
Display set
Access cfg
Device info
Operation levelExit Operator Maintenance Specialist
Device setup
Device setup (Continued)
Detailed setup (Continued)
F0505.ai
<5. Parameters of Magnetic Flowmeter> 143
IM 01E22A02-02EN
microSD (microSD)
Memo Memo 1 Memo 2 Memo 3
HART info Poll addr Loop curr mode Num req preamsNum resp preams
Ver/Num infoTransmitter type Option board IDTrans serial No Sensor serial NoMain soft revSnsr soft revInd soft rev Hard rev Dev id
MS codeModel codeSuffix config 1Suffix config 2Option 1Option 2 Option 3Option 4
RS MS code Model code Suffix config 1 Suffix config 2 Option 1 Option 2 Option 3 Option 4
Order info Tag NoLong tag Electrode sizeMS code
RS MS code Disp install
Protection Key code Write protect stsEnable write New password Soft seal status
Property Total space Available spaceFile system
microSD (microSD)Contents UnmountFormat Property
Order info
Ver/Num info
Memo
HART info
Protection
Operation level ExitOperator MaintenanceSpecialist
Device setup Device setup (Continued)
Detailed setup (Continued)
Device info (Continued)
F0506.ai
Status 0 Status 1 Status 2 Status 3 010:Main CPU FAIL 014:Snsr bd FAIL 021:PWM1stop 027:Restore FAIL 011:Rev calc FAIL 015:Snsr comm ERR 022:PWM2stop 028:Ind bd FAIL 012:Main EEP FAIL 016:AD 1 FAIL[Sig] 023:Opt bd mismatch 029:Ind bd EEP FAIL 013:MainEEPdflt 017:AD 2 FAIL[Excit] 024:Opt bd EEP FAIL 030:LCD drv FAIL
018:Coil open 025:OptbdA/DFAIL 031:Ind bd mismatch 019:Coil short 026:Opt bd SPI FAIL 032:Ind comm ERR 020:Exciter FAIL 033:microSD FAIL
Status 4 Status 5 Status 14 Status 15 050:Signaloverflow 060:SpancfgERR 067:Pls1cfgERR 080:AO1saturate051:Empty detect 062:AO 1 4-20 lmt 068:Pls2cfgERR 081:AO2saturate052:H/LHH/LLalm 063:AO 2 4-20 lmt 069:Nomisizecfg 082:Pls1saturate053:Adh over lv 4 064:AO 1 mlt rng 070:AdhcfgERR 083:Pls2saturate
065:H/LcfgERR 071:FLNcfgERR 084:AIsaturate066:DensitycfgERR 072:Log not start 085:Cable miscon
086:Coilinsulation131:Trans mismatch
Status 16 Status 17 Status 18 Status 19 087:Adhesion lv 3 095:Simulateactive 101:Paramrestorerun 120:Watchdog088:LC warn 096:AO1fix 102:Disp over 121:Poweroff089:Insudetect 097:AO2fix 103:SD size warn 122:Inst power FAIL 090:FLN over lv 3 098:Pls1fix 104:Bkupincmplt 123:Parambkuprun091:FLN over lv 4 099:Pls2fix 105:SD mismatch 124:Datalogrun092:AZ warn 100:AIfix 106:SD removal ERR 093:Verifwarn094:Fact noise warn
Status 20 130:DevID not enter
<5. Parameters of Magnetic Flowmeter> 144
IM 01E22A02-02EN
5.3 Menu Tree of HART CommunicationThestructureofDTMmenutreeisasblow.
(1) Process variables root menuDynamic variablesDevice variablesDevicevariablesstatusTotalizercountViewoutputsViewinputs
(2) Diagnostic root menuStatus/SelftestDiagnosis
(3) Maintenance root menuTime stampTestAutozeroAO/AItrimHigh/LowalarmconfigurationVerificationParambkup/restoreData loggingDisplay indication
(4) Device root menuEasysetupwizardBasicsetupDetailedsetup
<5. Parameters of Magnetic Flowmeter> 145
IM 01E22A02-02EN
(1) Process variables root menuMenu(Online)
Device variables
Device variables status
Totalizer count
View outputs
View inputs
Dynamic variables[PV][PV] data quality[PV] limit statusPV % rngeRange information[SV][SV] data quality[SV] limit status[TV][TV] data quality[TV] limit status[QV][QV] data quality[QV] limit statusPV isSV isTV isQV isChange PV mapChange SV mapChange TV mapChange QV map
Device variablesVelocityVolume flowMass flowTotalizer1Totalizer2Totalizer3Flow noiseCalorific value
Device variables statusVelocity data qualityVelocity limit statusVolume flow data qualityVolume flow limit statusMass flow data qualityMass flow limit statusTotalizer1 data qualityTotalizer1 limit statusTotalizer2 data qualityTotalizer2 limit statusTotalizer3 data qualityTotalizer3 limit statusFlow noise data qualityFlow noise limit statusCalorific value data qualityCalorific value limit status
Totalizer countTotalizer1 countTotalizer2 countTotalizer3 count
View outputsAO1 currentRange informationAO2 current
View inputsAI current
Process variables root menuDynamic variablesProcess variables root menu
F0507.ai
<5. Parameters of Magnetic Flowmeter> 146
IM 01E22A02-02EN
(2) Diagnostic root menu
Alarm
Condensed status mapDevice resetReset cfg chng flagSelf test
DiagnosisDiagnostic outputDiagnostic ExeAdhesion
Flow noise
Conductivity
EmptyCoil insulation thresholdIEX compareV peak hold valueIEX coil resistance
Diagnosis
AlarmAlarm record mask
Alarm record
Alarm out maskBurn out
Condensed status mapDevice statusStatus group 0Status group 1Status group 2Status group 3Status group 4Status group 5Ext dev statusDevice Diagnostic Status 0Device Diagnostic Status 1AO saturatedI/O and Subdevice StatusWirelessHART StatusAO fixedStatus group 14Status group 15Status group 16Status group 17Status group 18Status group 19Status group 20Reset condensed status map
AdhesionAdhesion functionAdhesion level 1Adhesion level 2Adhesion level 3Adhesion level 4ResultAdhesion check cycle
Flow noiseFlow noise functionFlow noise level 1Flow noise level 2Flow noise level 3Flow noise level 4ResultFlow noise dampingFlow noise span
ConductivityLow cunctivity functionConductivity low limitResult
EmptyElectrode voltage AElectrode voltage BResult
Alarm record maskAlarm record mask 1Alarm record mask 2Alarm record mask 3
Alarm recordAlarm record 1Alarm record time 1Alarm record 2Alarm record time 2Alarm record 3Alarm record time 3Alarm record 4Alarm record time 4
Alarm out maskAlarm out mask 1Alarm out mask 2Alarm out mask 3Alarm out mask 4
ResultAdhesion valueAdhesion status
ResultFlow noiseFlow noise status
ResultConductivity value
ResultEmpty status
F0508.ai
Status/Self testAlarm/Event device status
Diagnostic root menuStatus/Self test
Alarm/Event device statusDevice statusStatus group 0Status group 1Status group 2Status group 3Status group 4Status group 5Ext dev statusDevice Diagnostic Status 0Device Diagnostic Status 1AO saturatedI/O and Subdevice StatusWirelessHART StatusAO fixedStatus group 14Status group 15Status group 16Status group 17Status group 18Status group 19Status group 20
Diagnostic root menuMenu(Online)
<5. Parameters of Magnetic Flowmeter> 147
IM 01E22A02-02EN
(3) Maintenance root menu
Autozero
AO/AI trim
High/Low alarm configuration
Verification
Param bkup/restore
Data logging
Display indicationDisplay indicationLCD testSquawk
Data loggingFile nameInterval timeStart dateStart timeEnd timeLogging ExeLog1 selectLog2 selectLog3 selectLog4 select
Param bkup/restoreFactory backup nameFactory backup dateSD backup nameBackup ExeRestore ExeBackup name 1Backup date 1Backup name 2Backup date 2Backup name 3Backup date 3
VerificationDiagnostic outputVF modeVerification ExeVF NoResult
High/Low alarm configurationLow alarmLow low alarmHigh alarmHigh high alarmHi/Lo alarm hysteresis
ResultVF check resultVF operation timeMagnetic circuit resultExcitation circuit resultCalculation circuit resultVF device status resultConnection status result
AO/AI trimAO trim
AI trimAI trimAI trimClear AI trim
Output testDevice variable simulationDevice status bit simulation
Output testLoop testAO1Pulse1SO1AO2Pulse2SO2SO3
AO trimAO1 trimAO2 trimClear D/A trim 1Clear D/A trim 2
AutozeroAutozero ExeResult
ResultZero value
F0509.ai
Maintenance root menuTime stamp
TestTestRelease timeTest modeInput test
Time stampCurrent DateCurrent TimeOperation timeSet Date/Time
Input testVelocityVolume flowMass flowCalorific valueAISI3
Maintenance root menuMenu(Online)
<5. Parameters of Magnetic Flowmeter> 148
IM 01E22A02-02EN
(4) Device root menu
Mass flow
Calorie
Sensor
User span
Autozero
Detailed setupProcess variablesDetailed setup
Process variablesPV flow selectVelocity checkVelocity
Volume flow
Mass flow
Calorie
AutozeroAutozero ExeZero value
User spanUser span select AO1User unit AO1User span AO1User span select AO2User unit AO2User span AO2
SensorLow MFHigh MFFlow sensor selectNominal size unitNominal size
CalorieCalorific unitTime unitCalorific flow spanCalorific value damping AO/frequencyCalorific value damping pulse/totalSpecific heat
Mass flowMass flow unitTime unitMass flow spanMass flow damping AO/frequencyMass flow damping pulse/total
VelocityVelocity unitVelocity spanVelocity damping AO/frequencyVelocity damping pulse/total
Volume flowVolume flow unitTime unitVolume flow spanVolume flow damping AO/frequencyVolume flow damping pulse/total
Mass flowMass flow unitTime unitMass flow spanMass flow damping AO/frequencyMass flow damping pulse/total
CalorieCalorific unitTime unitCalorific flow spanCalorific value damping AO/frequencyCalorific value damping pulse/totalSpecific heat F0510.ai
Basic setupPV flow selectVelocity checkVelocity
Volume flow
Device root menuEasy setup wizard
Basic setup
Volume flowVolume flow unitTime unitVolume flow spanVolume flow damping AO/frequencyVolume flow damping pulse/total
VelocityVelocity unitVelocity spanVelocity damping AO/frequencyVelocity damping pulse/total
Easy setup wizardVolume flow
Pulse/Status out 1
Display settingAutozero Exe
Display settingDisplay select1Display select2Display select3
Pulse/Status out 1Rate unitRate valueFrequency at 0%Frequency at 100%
Volume flowVolume flow damping AO/frequencyVolume flow damping pulse/totalVolume flow unitTime unitVolume flow span
Device root menuMenu(Online)
<5. Parameters of Magnetic Flowmeter> 149
IM 01E22A02-02EN
Totalizer
Pulse/StatusPulse/StatusPulse/Status output 1
Pulse/Status output 2
Status output 3
Status input 3
TotalizerTotalizer1
Totalizer2
Totalizer3
Status input 3Status input3 active modeStatus input3 functionStatus input3 state
Status output 3Status output3 active modeStatus output3 function
Pulse/Status output 2Pulse2 active pulsePulse2 output modePulse2 selectPulse2 active modePulse2 fix widthPulse2 rate unitPulse2 rate valuePulse2 low cutPulse2 alarm outFrequency2 at 0%Frequency2 at 100%Status output2 function
Pulse/Status output 1Pulse1 output modePulse1 active modePulse1 fix widthPulse1 rate unitPulse1 rate valuePulse1 low cutPulse1 alarm outFrequency1 at 0%Frequency1 at 100%Status output1 function
Totalizer3Total3 unitTotal3 conv factorTotal3 low cutTotal3 fail optsTotal3 optionsTotal3 Start/StopTotal3 Reset/PresetTotal3 preset valueTotal3 set point
Totalizer2Total2 unitTotal2 conv factorTotal2 low cutTotal2 fail optsTotal2 optionsTotal2 Start/StopTotal2 Reset/PresetTotal2 preset valueTotal2 set point
Totalizer1Total1 unitTotal1 conv factorTotal1 low cutTotal1 fail optsTotal1 optionsTotal1 Start/StopTotal1 Reset/PresetTotal1 preset valueTotal1 set point
F0511.ai
Sensor
User span
Density
Temperature
User spanUser span select AO1User unit AO1User span AO1User span select AO2User unit AO2User span AO2
SensorLow MFHigh MFFlow sensor selectNominal size unitNominal size
TemperatureStandard temperatureMeasured temperatureCalorific fix tempTemp coef A1Temp coef A2
DensityDensity value selectDensity unitDensity fixed valueStandard densityCorrect density
Detailed setup (Continued)
Process variables (Continued)
<5. Parameters of Magnetic Flowmeter> 150
IM 01E22A02-02EN
AUX calculation
Display
DisplayLine select
Trend select
Display format
Display operation configuration
AUX calculationFlow directionRate limitDead timeNoise filterPulsing flowPower synchronizeSet power frequencyIEX power frequencyMes power frequencySet SIL
Display operation configurationDisplay contrastDisplay lineDisplay periodDisplay NE107Display alarmDisplay scrollDisplay dampingDisplay format dateDisplay inversionLanguageLanguage packageDisplay measure modeTrend offline lrvTrend offline urvDisplay installation
Display formatDisplay format PVDisplay format total 1Display format total 2Display format total 3
Trend selectTrend select 1Trend select 2Trend select 3Trend select 4
Line selectDisplay select1Display select2Display select3Display select4Display select5Display select6Display select7Display select8
F0512.ai
Detailed setup (Continued)
Analog output/input
Multi range
Analog output/inputAnalog output 1
Analog output 2
Analog input
Multi rangeForward span 2Reverse span 1Reverse span 2Auto range hystBi direction hyst
Analog inputAI functionAI high limitAI low limitAI currentAI unitAI URVAI LRV
Analog output 2AO2 selectAO2 low cutAO2 high limitAO2 low limitAO2 alarm out
Analog output 1AO1 low cutAO1 high limitAO1 low limitAO1 alarm outAO1 range mode
<5. Parameters of Magnetic Flowmeter> 151
IM 01E22A02-02EN
Protection
Event SettingEvent Notification ControlEvent Notification Retry TimeMax Update TimeEvent Debounce IntervalEvent StatusTime First unack Event TriggeredDevice Status MaskExt dev status MaskDevice Diagnostic Status 0 MaskDevice Diagnostic Status 1 MaskDevice Diagnostic Status 2 MaskDevice Diagnostic Status 3 MaskAO fixed MaskAO saturated MaskDevice Specific Status 0 MaskDevice Specific Status 1 MaskDevice Specific Status 2 MaskDevice Specific Status 3 MaskDevice Specific Status 4 MaskDevice Specific Status 5 MaskDevice Specific Status 14 MaskDevice Specific Status 15 MaskDevice Specific Status 16 MaskDevice Specific Status 17 MaskDevice Specific Status 18 MaskDevice Specific Status 19 MaskDevice Specific Status 20 Mask
Detailed burst setupset Detailed Burststop Detailed BurstBM1 SettingBM2 SettingBM3 Setting
Easy burst setupset Easy Burststop Easy BurstBurst modeBurst Commandslot0slot1slot2slot3
Event setupset Eventstop Eventacknowledge EventEvent Setting
Burst setupStop burstEasy burst setup
Detailed burst setup
ProtectionWrite protectEnable write 10minNew passwordSoftware seal
HART setupHART setupPoll addrLoop current modeNum req preamsNum resp preamsManufacturerModelDateDescriptorMessageDistributorFinal asmbly numMax dev varsDevice profileUniversal revFld dev revSoftware revHardware revBurst setup
Event setup
F0513.ai
Device informationDevice informationOrder information
Version/Number information
MemoMemoMemo 1Memo 2Memo 3
Order informationTagLong tagElectrode sizeBasic model codeSuffix config 1Suffix config 2Option 1Option 2Option 3Option 4Remote sensor basic model codeRemote sensor suffix config 1Remote sensor suffix config 2Remote sensor option 1Remote sensor option 2Remote sensor option 3Remote sensor option 4
Version/Number informationTransmitter typeOption board IDTransmitter serial NoSensor serial NoMain board revisionSensor board revisionIndicator board revisionHardware revDev id
Detailed setup (Continued)
<5. Parameters of Magnetic Flowmeter> 152
IM 01E22A02-02EN
Device statusProcess applied to the primary variable isoutsidetheoperatinglimitsofthefielddeviceProcess applied to the non-primary variableisoutsidetheoperatinglimitsofthefielddevicePVAnalogChannelSaturatedPV Analog Channel FixedFielddevicehasmorestatusavailableAresetorselftestofthefielddevicehasoccurred,orpowerhasbeenremovedand reappliedAmodificationhasbeenmadetotheconfigurationofthefielddeviceFielddevicehasmalfunctionedduetoahardwareerrororfailure
Status group 3 Status group 4 Status group 5 Ext dev status27:Parameter restore incomplete 50:Signaloverflow 60:Spanconfigurationerror Maintenancerequired28:Indicatorboardfailure 51:Empty pipe detection 62:Analogoutput14-20mAlimiterror Device variable alert29:IndicatorboardEEPROMfailure 52:H/LorHH/LLalarm 63:Analogoutput24-20mAlimiterror CriticalPowerFailure30:LCDdriverfailure 53:Adhesion over level 4 64:Analogoutput1multirangeerror Failure31:Indicator board mismatch 65:H/LHH/LLconfigurationerror OutofSpecification32:Indicatorcommunicationerror 66:Densityconfigurationerror FunctionCheck33:microSDfailure
Device Diagnostic Status 0 Device Diagnostic Status 1 AO saturated I/O and Subdevice StatusSimulationActive StatusSimulationActive SecondaryAnalogChannelSaturated SubdevicelistchangedNon-VolatileMemoryfailure DiscreteVariablesSimulationActive TertiaryAnalogChannelSaturated DuplicatemasterdetectedVolatile Memory error EventNotificationOverflow QuaternaryAnalogChannelSaturated SubdeviceMismatchWatchdogresetexecuted QuinaryAnalogChannelSaturated SubdevicewithDuplicateIDsFoundVoltageconditionsoutofrange Stale Data NoticeEnvironmentalconditionsoutofrangeElectronicfailureDeviceConfigurationLocked
WirelessHART Status AOfixed Status group 14 Status group 15Capacity Denied Secondary Analog Channel Fixed 67:Pulseoutput1configurationerror 80:Analogoutput1saturatedBandwidth Allocation Pending Tertiary Analog Channel Fixed 68:Pulseoutput2configurationerror 81:Analogoutput2saturatedBlockTransferPending QuaternaryAnalogChannelFixed 69:Nominalsizeconfigurationerror 82:Pulseoutput1saturatedRadioFailure QuinaryAnalogChannelFixed 70:Adhesionconfigurationerror 83:Pulseoutput2saturated
71:Flownoiseconfigurationerror 84:Analoginputsaturated72:Data logging not started 85:Cable misconnect
86:Coilinsulationwarning131:Transmitter type mismatch
Status group 16 Status group 17 Status group 18 Status group 1987:Adhesion over level 3 95:Simulationactive 101:Parameterrestorerunning 120:Watchdog88:Lowconductivitywarning 96:Analogoutput1fixed 102:Display over warning 121:Poweroff89:Insulationdetection 97:Analogoutput2fixed 103:microSD size warning 122:Instantpowerfailure90:Flow noise over level 3 98:Pulseoutput1fixed 104:Parameterbackupincomplete 123:Parameterbackuprunning91:Flow noise over level 4 99:Pulseoutput2fixed 105:microSD card mismatch 124:Dataloggingrunning92:Autozerowarning 100:Analoginputfixed 106:microSDcardremovalprocedureerror93:Verificationwarning94:Factory noise warning
Status group 20130:Device ID not entered
Status group 0 Status group 1 Status group 210:MainboardCPUfailure 14:Sensorboardfailure 21:PWM1stop11:Reversecalculationfailure 15:Sensorcommunicationerror 22:PWM2stop12:MainboardEEPROMfailure 16:A/D1failure[Signal] 23:Option board mismatch13:MainboardEEPROMdefault 17:A/D2failure[Exciter] 24:OptionboardEEPROMfailure
18:Coil open 25:OptionboardA/Dfailure19:Coil short 26:OptionboardSPIfailure20:Exciterfailure
153
IM 01E22A02-02EN
Revision Information Title : ADMAGTISeriesAXGMagneticFlowmeterHARTCommunicationTypeManualNo. : IM 01E22A02-02EN
Edition Data Page Revised Item1st June2017 — Newpublication
2nd Oct. 2017 2836737581100122135
4.1.7 Changetheunitsintheexample.4.3.4 DeleteNOTEaboutpulseoutput.4.11.5 ChangeNOTEaboutwiringconnectiondiagnosticfunction.4.11.6 AddNOTEaboutverificationfunction.4.13.2 Addthedescriptionaboutdisplayoftherestoreresult.5.1(2) ChangethedefaultvalueofNo.2-11.5.1(10) ChangethedefaultvalueofNo.10-1.5.1(14) ChangetheHARTcommunicationmenupathofNo.14-12.