8/11/2019 98 Mountaineer
1/216
Before driving
Introduction 2
Instrumentation 4
Controls and features 16
Seating and safety restraints 62
Starting and driving
Starting 94
Driving 100
Roadside emergencies 135
Servicing
Maintenance and care 154
Capacities and specifications 204
Reporting safety defects 212
Index 213
All rights reserved. Reproduction by any means, electronic or mechanicalincluding photocopying, recording or by any information storageand retrieval system or translation in whole or part is not permitted withoutwritten authorization from Ford Motor Company.
Copyright 1997 Ford Motor CompanyElemental Chlorine Free
Contents
1
8/11/2019 98 Mountaineer
2/216
ICONS
Indicates a warning. Read thefollowing section on Warnings fora full explanation.
Indicates vehicle informationrelated to recycling and otherenvironmental concerns will follow.
Correct vehicle usage and theauthorized disposal of wastecleaning and lubrication materialsare significant steps towardsprotecting the environment.
WARNINGS
Warnings provide informationwhich may reduce the risk ofpersonal injury and preventpossible damage to others, yourvehicle and its equipment.
BREAKING-IN YOUR VEHICLE
There are no particular breaking-inrules for your vehicle. During thefirst 1 600 km (1 000 miles) ofdriving, vary speeds frequently.This is necessary to give themoving parts a chance to break in.
If possible, you should avoid fulluse of the brakes for the first1 600 km (1 000 miles).
INFORMATION ABOUT THISGUIDE
The information found in thisguide was in effect at the time of
printing. Ford may change the
Introduction
2
8/11/2019 98 Mountaineer
3/216
contents without notice andwithout incurring obligation.
SPECIAL NOTICES
Notice to owners of utility typevehicles
Before you drive your vehicle,please read this Owners Guidecarefully. Your vehicle is not apassenger car. As with othervehicles of this type, failure tooperate this vehicle correctly mayresult in loss of control or anaccident.
Be sure to read Driving off roadin the Driving chapter as well asthe Four Wheeling supplementincluded with 4WD and utility typevehicles.
Using your vehicle as asnowplow
Do not use this vehicle forsnowplowing.
Using your vehicle as anambulance
Do not use this vehicle asan ambulance.
Your vehicle is not equipped withthe Ford Ambulance Preparationpackage.
Introduction
3
8/11/2019 98 Mountaineer
4/216
0
1
2
3
45 6
H
C
F
E
OFF
20
10
30
40
50 60 70
80
90
11 0
20 0
0 0 0 0 0 0
o o o o
10 020
40
60
80 100
120140
160
180
UNLEADED
FUEL ONLY
RSM
SETACC
COASTOFF
ON
SRS
H
H
Instrument cluster(pg. 6) Speed control
(pg. 26)
Driver side airbag
(pg. 73)
Headlampcontrol
(pg. 16)
Instrument paneldimmer switch
(pg. 17)
Tilt steeringwheel lever
(pg. 31)
Turn signal andwiper/washer
control(pg. 25)
Instrumentation
4
8/11/2019 98 Mountaineer
5/216
HI
LO OFF
REW
1
FF
2SIDE 1-2
3
FM 1
VOL PUSH ON
AM
FM BASSTREB BAL FADE
AUTO
SET
CLK
SEEK
TUNE
DISCS
SCAN
4
DOLBYSYSTEM
EJ TAPE CD
COMP
5
SHUFFLE
6
PUSH
ODON/OFF
Gearshift(includes
overdrive button)(pg. 104)
Electronic soundsystem; refer to
Audio Guide Rearwindow/washer
control(pg. 32)
Rear windowdefroster control
(pg. 24)
Climate controls(pg. 18)
Foglamp control(if equipped)
(pg. 16)
Instrumentation
5
8/11/2019 98 Mountaineer
6/216
WARNING LIGHTS AND CHIMES
Check engine
Your vehicle is equipped with acomputer that monitors theengines emission control system.This system is commonly known asthe On Board Diagnostics System(OBD II). This OBD II systemprotects the environment byensuring that your vehiclecontinues to meet governmentemission standards. The OBD II
system also assists the servicetechnician in properly servicingyour vehicle.
TheCheck Engine indicator lightilluminates when the ignition isfirst turned to the ON position tocheck the bulb. If it comes on afterthe engine is started, one of theengines emission control systemsmay be malfunctioning. The lightmay illuminate without adriveability concern being noted.The vehicle will usually be drivableand will not require towing.
C
0
1
2
3
45 6
R P M x1 0 0 0
ABS
!
BRAKE
CHECK
ENGINE
FUEL
RESET
E
F
HH
H
P R N D 2 1 THEFT
SPEED
CONT
4W D
HIGH
4W D
LOW
O/ D
OFF
L
L
1 0 M PH
2 0
5 0
6 0 7 0
3 0
4 0
8 0
9 0
km / h
0 0 0
1 01
0 01
2 01
0 0 0 0 0 040
60
80100
120
140
160
18020
DOOR
AJARCHECK
GAGE
CHECK
ENGINE
Instrumentation
6
8/11/2019 98 Mountaineer
7/216
What you should do if thecheck engine light illuminates
Light turns on solid:
This means that the OBD II systemhas detected a malfunction.
Temporary malfunctions may causeyour Check Engine light toilluminate. Examples are:
1. The vehicle has run out of fuel.(The engine may misfire or run
poorly.)2. Poor fuel quality or water in thefuel.
3. The fuel cap may not have beenproperly installed and securelytightened.
These temporary malfunctions canbe corrected by filling the fuel tankwith good quality fuel and/orproperly installing and securelytightening the gas cap. After threedriving cycles without these or anyother temporary malfunctionspresent, the Check Engine lightshould turn off. (A driving cycleconsists of a cold engine startupfollowed by mixed city/highwaydriving.) No additional vehicleservice is required.
If the Check Engine light remainson, have your vehicle serviced atthe first available opportunity.
Light is blinking:
Engine misfire is occurring whichcould damage your catalyticconverter. You should drive in amoderate fashion (avoid heavy
acceleration and deceleration) and
Instrumentation
7
8/11/2019 98 Mountaineer
8/216
have your vehicle serviced at thefirst available opportunity.
Under engine misfireconditions, excessive
exhaust temperatures coulddamage the catalytic converter,the fuel system, interior floorcoverings or other vehiclecomponents, possibly causing afire.
Fuel reset
Illuminates when the ignition keyis turned to the ON position andthe fuel pump shut-off switch hasbeen triggered. For moreinformation, refer to Fuel pumpshut-off switchin the Roadsideemergencies chapter.
Air bag readiness
Momentarily illuminates when theignition is turned ON. If the lightfails to illuminate, continues toflash or remains on, have thesystem serviced immediately.
Safety belt
Momentarily illuminates when theignition is turned ON to remindyou to fasten your safety belts. Formore information, refer to theSeating and safety restraintschapter.
FUEL
RESET
Instrumentation
8
8/11/2019 98 Mountaineer
9/216
Brake system warning
Momentarily illuminates when theignition is turned ONand theengine is off. Also illuminates whenthe parking brake is engaged.Illumination after releasing theparking brake indicates low brakefluid level.
Anti-lock brake system (ABS)
Momentarily illuminates when theignition is turned on and theengine is off. If the light remainson, continues to flash or fails toilluminate, have the systemserviced immediately.
Turn signal
Illuminates when the left or rightturn signal or the hazard lights areturned on. If one or both of the
indicators stay on continuously,check for a burned-out turn signalbulb. Refer to Exterior bulbs inthe Maintenance and carechapter.
High beams
Illuminates when the high beamheadlamps are turned on.
!
BRAKE
ABS
Instrumentation
9
8/11/2019 98 Mountaineer
10/216
Anti-theft system (if equipped)
Refer to Anti-theft system in theControls and features chapter.
Charging system
Momentarily illuminates when theignition is turned ON and the
engine is off. The light alsoilluminates when the battery is notcharging properly, requiringelectrical system service.
Check gage
Illuminates when the key is in theON position and the engine coolanttemperature is high, the engine oilpressure is low or the fuel level isnear empty. Refer to Enginecoolant temperature gauge,Engine oil pressure gaugeor
Fuel gaugein this chapter formore information.
Door ajar
Illuminates when the ignitionswitch is in the ON or STARTposition and any door is open.
THEFT
CHECK
GAGE
DOOR
AJAR
Instrumentation
10
8/11/2019 98 Mountaineer
11/216
O/D off (if equipped)
Illuminates when the transmissioncontrol switch has been pushed.When the light is on, thetransmission does not shift intooverdrive. If the light does notcome on when the transmissioncontrol switch is depressed or ifthe light flashes when you aredriving, have your vehicle serviced.
Speed control
This light comes on when eitherthe SET/ACCEL or RESUMEcontrols are pressed. It turns offwhen the speed control OFFcontrol is pressed, the brake isapplied or the ignition is turned tothe OFF position.
Safety belt warning chime
Chimes to remind you to fastenyour safety belts.
For information on the safety beltwarning chime, refer to theSeating and safety restraintschapter.
Supplemental restraint system(SRS) warning chime
For information on the SRSwarning chime, refer to theSeating and safety restraintschapter.
O/ D
OFF
SPEED
CON T
Instrumentation
11
8/11/2019 98 Mountaineer
12/216
Key-in-ignition warning chime
Sounds when the key is left in theignition in the OFF/LOCK or ACCposition and the drivers door isopened.
Headlamps on warning chime
Sounds when the headlamps orparking lamps are on, the ignitionis off (and the key is not in theignition) and the drivers door is
opened.
GAUGES
Speedometer
Indicates the current vehiclespeed.
C
0
1
2
3
45 6
R P M x1 0 0 0
ABS
CHECK
ENGINE
FUEL
RESET
E
F
HH
H
P R N D 2 1 THEFT
SPEED
CONT
4W D
HIGH
4W D
LOW
O/ D
OFF
L
L
1 0 M PH
2 0
5 0
6 0 7 0
3 0
4 0
8 0
9 0
km / h
0 0 0
1 01
0 01
2 01
0 0 0 0 0 040
60
80100
120
140
160
18020
DOOR
AJARCHECKGAGE
!
BRAKE
1 0 M PH
2 0
5 0
6 0 7 0
3 0
4 0
8 0
9 0
km / h
0 0 0
1 01
0 01
2 01
0 0 0 0 0 04 0
60
8010 0
12 0
14 0
16 0
18 020
Instrumentation
12
8/11/2019 98 Mountaineer
13/216
Engine coolant temperaturegauge
Indicates the temperature of theengine coolant. At normaloperating temperature, the needleremains within the normal area(the area between the H andC). If it enters the red section,the engine is overheating. Stop thevehicle, switch off the ignition and
let the engine cool. Refer toEngine coolant in theMaintenance and carechapter.
Never remove the coolantrecovery cap while the
engine is running or hot.
This gauge indicates thetemperature of the engine coolant,not the coolant level. If the coolantis not at its proper level ormixture, the gauge indication willnot be accurate.
Odometer
Registers the total kilometers(miles) of the vehicle.
C
H
1 0 M PH
2 0
5 0
6 0 7 0
3 0
4 0
8 0
9 0
km / h
0 0 0
1 01
0 01
2 01
0 0 0 0 0 040
60
8010 0
12 0
14 0
16 0
18 020
Instrumentation
13
8/11/2019 98 Mountaineer
14/216
Trip odometer
Registers the kilometers (miles) ofindividual journeys. To reset,depress the control.
Tachometer
Indicates the engine speed inrevolutions per minute.
Driving with your tachometerpointer in the red zone maydamage the engine.
Battery voltage gauge
This gauge shows the batteryvoltage when the ignition is in the
ON position. If the pointer movesand stays outside the normaloperating range (as indicated),have the vehicles electrical systemchecked as soon as possible.
1 0 M PH
2 0
5 0
6 0 7 0
3 0
4 0
8 0
9 0
km / h
0 0 0
1 01
0 01
2 01
0 0 0 0 0 040
60
8010 0
12 0
14 0
16 0
18 020
0
1
2
3
45 6
R PM x 1 0 0 0
L
H
Instrumentation
14
8/11/2019 98 Mountaineer
15/216
Engine oil pressure gauge
This shows the engine oil pressurein the system. Sufficient pressureexists as long as the needleremains in the normal range (thearea between the H and L).
If the gauge indicates lowpressure, switch off the engineimmediately. Check the oil level.Add oil if needed (refer toChecking and adding engine oilin the Maintenance and carechapter). If the oil level is correct,have your vehicle checked at yourdealership or by a qualifiedtechnician.
Fuel gauge
Displays approximately how muchfuel is in the fuel tank (when thekey is in the ON position). Thefuel gauge may vary slightly whenthe vehicle is in motion. Theignition should be in the OFFposition while the vehicle is beingrefueled. When the gauge firstindicates empty, there is a smallamount of reserve fuel in the tank.When refueling the vehicle fromempty indication, the amount offuel that can be added will be lessthan the advertised capacity due tothe reserve fuel.
The FUEL DOOR icon and arrowindicates which side of the vehiclethe fuel filler door is located.
H
L
E
F
Instrumentation
15
8/11/2019 98 Mountaineer
16/216
HEADLAMP CONTROL
Rotate the headlamp controlclockwise to the first position toturn on the parking lamps only.Rotate to the second position toalso turn on the headlamps.
Foglamp control (if equipped)
Turn on the low-beam headlampsand press the foglamp control toactivate the foglamps. The foglampcontrol button will illuminate whenthe foglamps are on.
Press the foglamp control a secondtime to deactivate the foglamps.
Daytime running lamps (DRL)(if equipped)
Turns the highbeam headlamps on
with a reduced output. To activate:
the engine must be running
the gearshift must not be in P(Park)
the headlamp control is in theOFF or Parking lamps position.
The Daytime RunningLight (DRL) system will
not illuminate the tail lamps andparking lamps. Turn on yourheadlamps at dusk. Failure to doso may result in a collision.
OFF
Controls and features
16
8/11/2019 98 Mountaineer
17/216
High beams
Push forward to activate.
Flash to pass
Pull back to activate and release todeactivate.
PANEL DIMMER CONTROL
Use to adjust the brightness of theinstrument panel during headlightand parklamp operation.
Rotate up to brighten. Rotate down to dim.
Use to control the dome lamps.
Rotate all the way up to turn on.
Rotate all the way down tooverride.
DIM
Controls and features
17
8/11/2019 98 Mountaineer
18/216
CLIMATE CONTROL SYSTEM
Manual heating and airconditioning system
Fan speed control
Controls the volume of aircirculated in the vehicle.
Temperature control knob
Controls the temperature of theairflow inside the vehicle.
Mode selector control
Controls the direction of theairflow to the inside of the vehicle.
The air conditioning compressorwill operate in all modes except
and . However, the airconditioning will only function ifthe outside temperature is about10C (50F) or above.
Since the air conditioner removesconsiderable moisture from the airduring operation, it is normal ifclear water drips on the ground
under the air conditioner drain
OFF
A/C
MAX
A/C
OFF
A/C
MAX
A/C
Controls and features
18
8/11/2019 98 Mountaineer
19/216
while the system is working andeven after you have stopped thevehicle.
Under normal conditions, yourvehicles climate control systemshould be left in any position otherthan MAX A/C or OFF when thevehicle is parked. This allows thevehicle to breathe through theoutside air inlet duct.
MAX A/C-Uses recirculated air
to cool the vehicle. MAX A/C isnoisier than A/C but moreeconomical and will cool theinside of the vehicle faster.Airflow will be from theinstrument panel registers. Thismode can also be used toprevent undesirable odors fromentering the vehicle.
A/C-Uses outside air to cool thevehicle. It is quieter than MAXA/C but not as economical.Airflow will be from theinstrument panel registers.
(Vent)-Distributes outsideair through the instrument panelregisters. However, the air willnot be cooled below the outsidetemperature because the airconditioning does not operate inthis mode.
OFF-Outside air is shut out andthe fan will not operate. Forshort periods of time only, usethis mode to preventundesirable odors from enteringthe vehicle.
Controls and features
19
8/11/2019 98 Mountaineer
20/216
(Panel andfloor)-Distributes outside airthrough the instrument panelregisters and the floor ducts.Heating and air conditioningcapabilities are provided in thismode. For added customercomfort, when the temperaturecontrol knob is anywhere inbetween the full hot and fullcold positions, the airdistributed through the floorducts will be slightly warmerthan the air sent to theinstrument panel registers.
(Floor)-Allows for maximumheating by distributing outsideair through the floor ducts.However, the air will not becooled below the outsidetemperature because the airconditioning does not operate inthis mode.
(Floor anddefrost)-Distributes outside air
through the windshield defrosterducts and the floor ducts.Heating and air conditioningcapabilities are provided in thismode. For added customercomfort, when the temperaturecontrol knob is anywhere inbetween the full hot and fullcold positions, the airdistributed through the floorducts will be slightly warmerthan the air sent to theinstrument panel registers. Foradded customer comfort, whenthe temperature control knob is
anywhere in between the full
Controls and features
20
8/11/2019 98 Mountaineer
21/216
hot and full cold positions, theair distributed through the floorducts will be slightly warmerthan the air sent to thewindshield defroster ducts. Ifthe temperature is about 10C(50F) or higher, the airconditioner will automaticallydehumidify the air to preventfogging.
-Distributes outside air
through the windshield defrosterducts. It can be used to clear iceor fog from the windshield. Ifthe temperature is about 10C(50F) or higher, the airconditioner will automaticallydehumidify the air to preventfogging.
Operating tips
In humid weather, selectbefore driving. This will
prevent your windshield fromfogging. After a few minutes,select any desired position.
To prevent humidity buildupinside the vehicle, dont drivewith the climate control systemin the OFF position.
Dont put objects under thefront seat that will interfere withthe airflow to the back seats.
Controls and features
21
8/11/2019 98 Mountaineer
22/216
Remove any snow, ice or leavesfrom the air intake area (at thebottom of the windshield underthe hood).
If your vehicle has been parkedwith the windows closed during
hot weather, the air conditionerwill do a much faster job ofcooling if you drive for two orthree minutes with the windowsopen. This will force most of thehot, stale air out of the vehicle.Then operate your airconditioner as you wouldnormally.
When placing objects on top ofyour instrument panel, becareful to not place them overthe defroster outlets. Theseobjects can block airflow and
reduce your ability to seethrough your windshield. Also,avoid placing small objects ontop of your instrument panel.These objects can fall down intothe defroster outlets and blockairflow and possibly damageyour climate control system.
Controls and features
22
8/11/2019 98 Mountaineer
23/216
Rear console climate controls(if equipped)
Depending on the equipmentpackage of your vehicle, the rearconsole may not be equipped withrear console audio/climate controls.
Turn the air distribution control tothe desired airflow position.
The instrument panel climatecontrols must be on in order forthe rear climate control consolecontrols to work.
Turn the fan speed control to thedesired position.
Select for air to flow through
these vents:
- VOLUME + MODE
SEEK MEMORY
- VOLUME + MODE
SEEK MEMORY
SEEK
VOLUME + BAND
MEMORY
Controls and features
23
8/11/2019 98 Mountaineer
24/216
Select for air to flow throughthese vents:
REAR WINDOW DEFROSTER
The rear defroster control islocated on the instrument panel.
Press the defroster control to clearthe rear window of thin ice andfog.
The small LED will illuminate
when the defroster is activated.The ignition must be in the ONposition to operate the rearwindow defroster.
The defroster turns offautomatically after 10 minutes orwhen the ignition is turned to theOFF position. To manually turn offthe defroster before ten minuteshave passed, push the controlagain.
SEEK
VOLUME + BAND
MEMORY
Controls and features
24
8/11/2019 98 Mountaineer
25/216
4WD CONTROL (IF EQUIPPED)
This control operates the 4WD.Refer to Four-wheel drive (4WD)operation in the Driving chapterfor more information.
AUDIO SYSTEM
Refer to the Audio Guide in yourowner portfolio.
TURN SIGNAL CONTROL
Push down to activate the leftturn signal.
Push up to activate the rightturn signal.
HIGH LOWAUTO
Controls and features
25
8/11/2019 98 Mountaineer
26/216
SPEED CONTROL
To turn speed control on
Press ON.
Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph).
Do not use the speedcontrol in heavy traffic or
on roads that are winding,slippery, or unpaved.
Do not shift the gearshiftlever into N (Neutral) with
the speed control on.
To turn speed control off
Press OFF or
Turn off the vehicle ignition.
Once speed control is switched off,the previously programmed setspeed will be erased.
OFF
ON
OFF
ON
Controls and features
26
8/11/2019 98 Mountaineer
27/216
To set a speed
Press SET ACC/SET ACCEL.For speed control to operate,the speed control must be ONand the vehicle speed must begreater than 48 km/h (30 mph).
If you drive up or down a steephill, your vehicle speed may varymomentarily slower or faster thanthe set speed. This is normal.
Speed control cannot reduce thevehicle speed if it increases abovethe set speed on a downhill. Ifyour vehicle speed is faster thanthe set speed while driving on adownhill, you may want to shift tothe next lower gear or apply thebrakes to reduce your vehiclespeed.
If your vehicle slows down morethan 16 km/h (10 mph) below yourset speed on an uphill, your speedcontrol will disengage. This isnormal. PressingRES/RSM/RESUME will re-engageit.
Do not use the speedcontrol in heavy traffic or
on roads that are winding,slippery, or unpaved.
RSM
SET
ACC
COAST
Controls and features
27
8/11/2019 98 Mountaineer
28/216
To set a higher set speed
Press and hold SET ACC/SETACCEL. Release the controlwhen the desired vehicle speedis reached or
Press and release SET ACC/SETACCEL. Each press will increasethe set speed by 1.6 km/h(1 mph) or
Accelerate with your acceleratorpedal, then press and releaseSET ACC/SET ACCEL.
You can accelerate with theaccelerator pedal at any timeduring speed control usage.Releasing the accelerator pedal willreturn your vehicle to thepreviously programmed set speed.
To set a lower set speed
Press and hold CST/COAST.Release the control when the
desired speed is reached or
Press and release CST/COAST.Each press will decrease the setspeed by 1.6 km/h (1 mph) or
RSM
SET
ACC
COAST
RSM
SET
ACC
COAST
Controls and features
28
8/11/2019 98 Mountaineer
29/216
Depress the brake pedal. Whenthe desired vehicle speed isreached, press SET ACC/SETACCEL.
To disengage speed control
Depress the brake pedal.
Disengaging the speed control willnot erase the previouslyprogrammed set speed.
Pressing OFF will erase the
previously programmed set speed.
RSM
SET
ACC
COAST
OFF
ON
Controls and features
29
8/11/2019 98 Mountaineer
30/216
To return to a previously setspeed
Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed must be fasterthan 48 km/h (30 mph).
Indicator light
This light comes on when eitherthe SET ACC/SET ACCEL orRES/RSM/RESUME controls arepressed. It turns off when thespeed control OFF control ispressed, the brake is applied orthe ignition is turned to the OFFposition.
RSM
SET
ACC
COAST
SPEED
CON T
Controls and features
30
8/11/2019 98 Mountaineer
31/216
TILT STEERING
Pull the steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the controlto lock the steering wheel inposition.
Never adjust the steeringwheel when the vehicle is
moving.
HAZARD FLASHER
For information on the hazardflasher control, refer to Hazardlights control in the Roadsideemergencies chapter.
Controls and features
31
8/11/2019 98 Mountaineer
32/216
WINDSHIELD WIPER/WASHERCONTROLS
Rotate the windshield wipercontrol to the desired interval, lowor high speed position.
The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals.
Push the control on the end of thestalk to activate washer. Push andhold for a longer wash cycle.
Speed dependent wipers
When the windshield wiper controlis set on the intermittent settings,speed-sensitive front wipersautomatically adjust as thevehicles speed increases.
Rear window wiper and washer
For rear wiper operation, rotatethe rear window wiper and washercontrol to the desired intervalposition.
PUSH
OFFR.WIPE
HI
Controls and features
32
8/11/2019 98 Mountaineer
33/216
Press the control for rear washerfluid operation.
OVERHEAD CONSOLE(IF EQUIPPED)
The appearance of your vehiclesoverhead console will varyaccording to your option package.All overhead consoles show theoutside temperature and compassdisplay.
Storage compartment(if equipped)
Press the OPEN control to openthe storage compartment. The
door will open slightly and can bemoved to full open.
Installing a garage door opener(if equipped)
The storage compartment can beconverted to accommodate avariety of aftermarket garage dooropeners:
PUSH
OFFR.WIPE
HI
MODE
LAMP
LAMP
OPEN
Controls and features
33
8/11/2019 98 Mountaineer
34/216
Remove the storage clip fromthe door.
Place Velcrohook onto side ofaftermarket transmitter oppositeof actuator control.
Place the transmitter intostorage compartment, controldown.
Place the provided height
adaptors onto the back of theGARAGE control as needed.
Press the GARAGE control toactivate the transmitter.
Moon roof (if equipped)
Press and release the rearportion of the moon roof controlto open.
To halt motion at any pointduring one-touch opening, pressthe control a second time.
Press and hold (as desired) thefront portion of the moon roofcontrol to close.
MODELAMP LAMP
Controls and features
34
8/11/2019 98 Mountaineer
35/216
The moon roof has a sliding shadethat can be manually opened orclosed when the glass panel isshut. To close the shade, pull ittoward the front of the vehicle.
Do not let children playwith the moon roof. They
may seriously hurt themselves.
Electronic compass/temperature
displayA compass and outsidetemperature display are containedin the overhead console.
The compass and temperaturedisplay can be turned off and onby pressing the MODE control onthe overhead console. The vehicleheading is displayed as one of N,NE, E, SE, S, SW, W and NW.
Outside air temperature
The temperature can be displayedin Centigrade or Fahrenheit bypressing the MODE control.
If the outside temperature fallsbelow 3.3C (38F), the displaywill alternate from ICE to theoutside temperature at a twosecond rate for one minute.
LAMP MODE LAMP
9 VAR
Controls and features
35
8/11/2019 98 Mountaineer
36/216
The compass reading may beaffected when you drive near largebuildings, bridges, power lines andpowerful broadcast antenna.Magnetic or metallic objects placedin or on the vehicle may also affectcompass accuracy. Adjustmentsmay need to be made to the zoneand calibration of the compass.
Compass zone adjustment
1. Determine which magnetic zoneyou are in by referring to the zonemap.
OPEN
GARAGE
LAM P M ODE LAM P
73 NW
1
2
3
4
5
6
7 8 9
10
11
12
13
14
15
Controls and features
36
8/11/2019 98 Mountaineer
37/216
2. Press and hold the MODEcontrol until VAR appears in thedisplay, then release. The displayshould show the current zonenumber.
3. Press the MODE control untilthe desired zone number appears.The display will flash and thenreturn to normal operation. Thezone is now updated.
Compass calibration adjustment
Perform this adjustment in anopen area free from steelstructures and high voltage lines:
Press and hold the MODEcontrol until CAL appears in thedisplay (approximately eightseconds) and release.
Drive the vehicle slowly (lessthan 5 km/h [3 mph]) in circlesuntil CAL indicator turns off in
about 23 complete circles.AUTOLAMP DELAY SYSTEM(IF EQUIPPED)
The autolamp sets the headlampsto turn on and off automatically.The autolamp may be set to:
turn on the lamps automaticallyat night
turn off the lamps automaticallyduring daylight
keep the lamps on for up tothree minutes after the key isturned to OFF
LAMP MODE LAMP
9 VAR
LAMP MODE LAMP
CAL
Controls and features
37
8/11/2019 98 Mountaineer
38/216
Setting autolamp
1. Make sure the headlamp controlis in the OFF position. Leaving theheadlamp control on will overridethe autolamp.
2. Turn the ignition to the ONposition or start the vehicle.
3. Slide the delay control all theway to the left.
The further you move the knob tothe right, the longer the headlampsstay on after the ignition is turnedto the OFF position. The autolampwill keep the headlamps on for amaximum of three minutes afterthe ignition is turned to OFF.
4. The autolamp automaticallyturns the lamps on and off. Theindicator light will illuminate whenthe headlamps turn on.
Automatic dimming rear viewmirror
The autolamp/automatic dimmingmirror is equipped with anautomatic dimming feature. Thisfeature will change from thenormal state to the non-glareactive state when bright lights(glare) reach the mirror. When themirror detects bright light fromfront or behind, it will adjustautomatically to minimize glare.
The mirror will automatically
return to the normal position
OFF
AUTOLAMPOFF MAX.
DELAY
AUTOLAMPOFF MAX.
DELAY
Controls and features
38
8/11/2019 98 Mountaineer
39/216
whenever the vehicle is placed inR (Reverse) (when the mirror is inthe ON position). This helps toensure a bright clear view in themirror when backing up.
POWER WINDOWS
Press and hold the rocker switchesto open and close windows.
Press the top portion of therocker switch to close.
Press the bottom portion of therocker switch to open.
AUTO
AUTO
Controls and features
39
8/11/2019 98 Mountaineer
40/216
One touch down
Press AUTO and release quickly.The window will open fully.Depress again to stop windowoperation.
Window lock
The window lock feature allowsonly the driver to operate thepower windows.
POWER DOOR LOCKS
Press U to unlock all doors and Lto lock all doors.
Two step unlocking(if equipped)
When unlocking the driver doorwith the key, turn it once towardthe rear of the vehicle to unlockthat door only. Turn the key to therear a second time to unlock alldoors.
AUTO
WINDOW LOCK
Controls and features
40
8/11/2019 98 Mountaineer
41/216
If the vehicle is equipped with theoptional perimeter alarm system,this feature will work from alldoors.
CHILDPROOF DOOR LOCKS
When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when the
doors are unlocked.The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one doorwill not automatically set the lockfor both doors.
Move lock control up to engage thelock. Move control down todisengage childproof locks.
POWER SIDE VIEW MIRRORS
To adjust your mirrors:
1. Select to adjust the leftmirror or to adjust the rightmirror.
2. Move the control in thedirection you wish to tilt themirror.
Controls and features
41
8/11/2019 98 Mountaineer
42/216
3. Return to the center position tolock mirrors in place.
CENTER CONSOLE
Your vehicle may be equipped witha variety of console features. Theseinclude:
utility compartment withcassette/compact disc storage
auxiliary power point cupholders
tissue box holder
cellular phone (if equipped)
ashtray or removable ashcup
compact disc changer (ifequipped)
Use only soft cups in thecupholder. Hard objects
can injure you in a collision.
AUXILIARY POWER POINT
The power point is an additionalpower source for electricalaccessories.
Controls and features
42
8/11/2019 98 Mountaineer
43/216
POSITIVE RETENTION FLOORMAT
Position the floor mat so that theeyelet is over the pointed end ofthe retention post and rotateforward to lock in. Make sure thatthe mat does not interfere with theoperation of the accelerator or thebrake pedal. To remove the floormat, reverse the installation
procedure.
REAR LIFTGATE
The liftgate area is only intendedfor cargo, not passengers. You canopen and close the liftgate fromoutside the vehicle. It cannot beopened from inside the cargo area.
To open the liftgate window,unlock the liftgate (with the keyor power door locks) and push
the key lock cylinder. To open the liftgate, unlock the
liftgate and pull up on thehandle under the license platelamp shield.
To lock the liftgate and the liftgatewindow, use the key or the powerdoor locks, depress the key lockcylinder or press the door lockswitch on the left side of the cargoarea.
The liftgate door and windowshould be closed before drivingyour vehicle. If not, possible
Controls and features
43
8/11/2019 98 Mountaineer
44/216
damage may occur to the liftgatedoor lift cylinders and attachinghardware.
Make sure that the liftgatedoor and/or window are
closed to prevent exhaust fumesfrom being drawn into thevehicle. This will also preventpassengers and cargo from fallingout. If you must drive with theliftgate door or window open,
keep the vents open so outsideair comes into the vehicle.
CARGO COVER (IF EQUIPPED)
Your vehicle may be equipped witha cargo area shade that covers theluggage compartment of yourvehicle.
To install the shade:
1. Fasten the cover into themounting brackets (make sure the
cover is right side up).2. Pull the end of the shade towardyou and hook the sides into thenotches in the rear trim panels.
To prevent the possibilityof injuries, the fasteners
for the cargo area cover must beproperly attached to themounting clips on the rear trimpanels.
Controls and features
44
8/11/2019 98 Mountaineer
45/216
Do not place any objectson the cargo area cover.
They may obstruct your vision orstrike occupants of the vehicle inthe case of a sudden stop orcollision.
Rewinding the shade
With extended use, the cargoshade may lose its spring tension.
If this occurs, the shade must bemanually rewound. This is atwo-person operation.
1. Remove the shade from thevehicle and extend it with thesmooth grain facing you.
2. Wrap the vinyl around the rollertube twice. Tuck the edges of thevinyl inside the end cap with eachwrap.
3. Fold the edges of the vinyltowards the center, making sure
that the edges clear the end capslots. Use tape or a rubber band tohold the vinyl to the left side ofthe tube.
4. Push in the right end cap(marked RH) about 14 of the totallength to disengage the clutch andhold the end cap in while turningthe roller tube toward you 14times.
Controls and features
45
8/11/2019 98 Mountaineer
46/216
5. Let go of the right end cap. Theclutch will now engage and stopthe shade from losing its springtension.
6. Unfold the vinyl and place itinto the end cap slots.
7. Insert the shade into the sidemounting brackets and check tomake sure that it operatesproperly.
REMOTE ENTRY SYSTEMThe remote entry system allowsyou to lock or unlock all vehicledoors without a key.
The remote entry features onlyoperate with the ignition in theOFF position.
Unlocking the doors
Press this control to unlock thedriver door. The interior lamps willilluminate.
Press the control a second timewithin five seconds to unlock alldoors.
Controls and features
46
8/11/2019 98 Mountaineer
47/216
Locking the doors
Press this control to lock all doors.
To confirm all doors are closed andlocked, press the control a secondtime within five seconds. Thedoors will lock again, the horn willchirp and the lamps will flash.
If any of the doors are ajar, thehorn will make two quick chirps,
reminding you to properly close alldoors.
Sounding a panic alarm
Press this control to activate thealarm.
To deactivate the alarm, press thecontrol again or turn the ignitionto ACC or ON.
This device complies with part 15of the FCC rules and with RS-210of Industry Canada. Operation is
subject to the following twoconditions: (1) This device maynot cause harmful interference,and (2) This device must acceptany interference received,including interference that maycause undesired operation.
Changes or modifications notexpressly approved by theparty responsible forcompliance could void theusers authority to operate theequipment.
Controls and features
47
8/11/2019 98 Mountaineer
48/216
Replacing the battery
The transmitter is powered by onecoin type three-volt lithium batteryCR2032 or equivalent. Typicaloperating range will allow you tobe up to 10 meters (33 feet) awayfrom your vehicle. A decrease inoperating range can be caused by:
battery weakness due to timeand use
weather conditions
nearby radio towers
structures around the vehicle
other vehicles parked next tothe vehicle
To replace the battery:
1. Twist a thin coin between thetwo halves of the transmitter nearthe key ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART.
2. Place the positive (+) side ofnew battery in the same
orientation. Refer to the diagraminside the transmitter unit.
3. Snap the two halves backtogether.
Controls and features
48
8/11/2019 98 Mountaineer
49/216
Replacing lost transmitters
Take all your vehicles transmittersto your dealer for reprogrammingif:
a transmitter is lost or
you want to purchase additionaltransmitters (up to four may beprogrammed).
To reprogram the transmitters,
place the key in the ignition andswitch from OFF to ON five timesin rapid succession (within 10seconds). After doors lock/unlock,press any button on alltransmitters (up to four). Whencompleted, switch the ignition toOFF.
All transmitters must beprogrammed at the same time.
Reprogramming transmitters
To reprogram all transmitters,place the key in the ignition and
switch from OFF to ON eight timesin a row (within 10 seconds). Afterdoors lock/unlock, press anybutton on all transmitters (up tofour). When completed, switch theignition to OFF.
All transmitters must bereprogrammed at the same time.
Illuminated entry
The interior lamps and the puddlelamps (located on the bottom ofthe exterior rear view mirrors)illuminate when the remote entry
system is used to unlock the
Controls and features
49
8/11/2019 98 Mountaineer
50/216
door(s) or sound the personalalarm.
The system automatically turns offafter 25 seconds or when theignition is turned to the START orACC position. The dome lampswitch (if equipped) must not beset to the OFF position for theilluminated entry system tooperate.
The inside lights will not turn off
if:
they have been turned on withthe dimmer control or
any door is open.
Battery saver will shut off theinterior lamps 45 minutes after thelast door is closed.
Autolock
Autolock is a feature that willautomatically lock all doors when:
all vehicle doors, liftgate andliftgate window are fully closed
the ignition key is in the ONposition
you shift into or through R(Reverse)
the brake pedal is released
The autolock feature repeats when:
any door is opened and thenclosed
the brake pedal is released
Deactivating autolock
Before following the activation or
deactivation procedures, make sure
Controls and features
50
8/11/2019 98 Mountaineer
51/216
that the anti-theft system is notarmed, the ignition is OFF and allvehicle doors and liftgate windoware closed.
1. Enter the 5 digit entry code.
2. Press and release the 3/4 controlwhile holding the 7/8 control.
3. Release the 7/8 control.
The horn will chirp once if
autolock was deactivated or twice(one short and one long chirp) ifautolock was activated.
To reactivate autolock, repeatsteps 1 through 4.
Autolock can also be activated ordeactivated using the followingprocedure:
You must complete steps 1 through5 within 30 seconds or theprocedure will have to berepeated. If the procedure needsto be repeated, you must wait
30 seconds.1. Turn the ignition key to ON.
2. Press the power door unlockcontrol three times.
3. Turn the ignition key from ONto OFF.
4. Press the power door unlockcontrol three times.
5. Turn the ignition key back toON. The doors will lock andunlock.
1 2 3 4 5 6 7 8 9 0
Controls and features
51
8/11/2019 98 Mountaineer
52/216
6. Press the power door unlockswitch. The horn will chirp onceupon successful toggling of theAutolock feature.
7. Turn ignition to OFF. The hornwill chirp to confirm procedure iscomplete.
Keyless entry system(if equipped)
With the keyless entry keypad, youcan:
lock or unlock the vehicle doorswithout using the key
arm and disarm the perimeteralarm system (if equipped)
activate/deactivate the autolockfeature
See also Remote entry system andPerimeter alarm system in thischapter for more information.
Your vehicle has a factory-set 5
digit code that operates thekeyless entry system. You can alsoprogram your own 5 digit personalentry code.
The factory-set code is located:
on the owners wallet card in theglove compartment
taped to the computer module
When pressing the controls on thekeyless entry keypad, press themiddle of the buttons to ensure agood activation.
1 2 3 4 5 6 7 8 9 0
Controls and features
52
8/11/2019 98 Mountaineer
53/216
Programming your ownpersonal entry code
1. Enter the factory-set code(keypad will illuminate whenpressed).
2. Press the 1/2 control within fiveseconds of step 1.
3. Enter your personal 5 digitcode. Enter each digit within five
seconds of the previous one.
Do not set a code that includesfive of the same number orpresents them in sequential order.Thieves can easily figure out thesetypes of codes.
Your personal code does notreplace the permanent code thatthe dealership gave you. You canuse either code to unlock yourvehicle. If a second personal codeis entered, the module will erasethe first personal code in favor ofthe new code.
If you wish to erase your personalcode, use the followinginstructions:
1 2 3 4 5 6 7 8 9 0
Controls and features
53
8/11/2019 98 Mountaineer
54/216
Erasing personal code
1. Enter the factory-set code.
2. Press 1/2 within five seconds ofstep one.
3. Press the 7/8 and 9/0 controls atthe same time within five secondsof step two.
The system will now only respondto the factory-set code.
Unlocking the doors with thekeyless entry system
To unlock the drivers door, entereither the factory-set code orpersonal code (each digit pressedwithin 5 seconds of the priordigit). The interior lamps willilluminate.
To unlock all doors, enter thefactory-set code or personal code(driver door unlocks) and pressthe 3/4 control within 5 seconds.
Locking the doors with thekeyless entry system
To lock all the doors, press 7/8 and9/0 at the same time. It is notnecessary to first enter the keypadcode.
This will arm your perimeter alarmsystem (if equipped). Refer toPerimeter alarm system in this
chapter for more information.
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
1 2 3 4 5 6 7 8 9 0
Controls and features
54
8/11/2019 98 Mountaineer
55/216
Operating your perimeter alarmsystem (if equipped) from thekeyless entry pad
The keyless entry system arms bypressing 7/8 and 9/0.
To disarm or reset a triggeredalarm, enter the five digit code.
All doors must be fully closed forthe alarm system to arm. Refer to
the Perimeter alarm systemsection, if equipped, in this chapterfor more details.
PERIMETER ALARM SYSTEM
Arming the system
When armed, this system will helpprotect your vehicle fromunauthorized entry. Whenunauthorized entry occurs, thesystem will flash the headlamps,parking lamps and the theftindicator lamp and will chirp thehorn.
The system is ready to armwhenever the ignition is turnedOFF. Any of the following actionswill prearm the alarm system:
Press the remote entry lockcontrol
Open a door and press thepower door lock control to lockthe doors
1 2 3 4 5 6 7 8 9 0
Controls and features
55
8/11/2019 98 Mountaineer
56/216
Pressing 7/8 and 9/0 on thekeyless entry pad at the sametime to lock the doors (doorsopened or closed).
If a door is open, the system isprearmed and is waiting for thedoor to close. The theft indicator
on the instrument cluster will belit continuously when the system isprearmed.
Once the doors are closed, thesystem will arm in 30 seconds.
When you press the lock controltwice within 5 seconds, the hornwill chirp once to let you knowthat the system is armed.
If the doors are not closed and youpress the remote entry transmittertwice to confirm the doors are
locked, the horn will chirp twice towarn you that the system is notarming.
Disarming the system
You can disarm the system by anyof the following actions:
1 2 3 4 5 6 7 8 9 0
Controls and features
56
8/11/2019 98 Mountaineer
57/216
Unlock the doors by using yourremote entry transmitter.
Unlock the doors with a key.Turn the key full travel (towardthe front of the vehicle) to makesure the alarm disarms.
Unlock the doors by using yourkeyless entry keypad.
Turn ignition to ACC or ON.
Press the panic control on theremote entry transmitter. Thiswill disarm the system only ifthe alarm is sounding.
SecuriLock anti-theft system
The SecuriLock anti-theft systemprovides an advanced level ofvehicle theft protection. Yourvehicles engine can only be startedwith the two special SecuriLockelectronically coded keys providedwith your vehicle. Each time you
start your vehicle, the
1 2 3 4 5 6 7 8 9 0
Controls and features
57
8/11/2019 98 Mountaineer
58/216
SecuriLockkey is read by theSecuriLock anti-theft system. Ifthe SecuriLockkey identificationcode matches the code stored inthe SecuriLockanti-theft system,the vehicles engine is allowed tostart. If the SecuriLockkeyidentification code does not matchthe code stored in the system or ifa SecuriLockkey is not detected(vehicle theft situation), thevehicles engine will not operate.
Spare SecuriLockkeys can bepurchased from your dealershipand programmed to yourSecuriLockanti-theft system.Refer to Programming spareSecuriLockkeys for moreinformation.
If one or both of your SecuriLockkeys are lost or stolen and youwant to ensure the lost or stolenkey will not operate your vehicle,bring your vehicle and all availableSecuriLockkeys to your
dealership for reinitialization.Theft indicator
The theft indicator on theinstrument cluster will operate asfollows:
When the ignition is OFF, thetheft indicator will flash brieflyevery 2 seconds to indicate theSecuriLock system isprotecting your vehicle.
When the ignition is turned toRUN or START, the theftindicator will light for 3 seconds
and then go out. If the theft
Controls and features
58
8/11/2019 98 Mountaineer
59/216
indicator stays on for anextended period of time orflashes rapidly, have the systemserviced by your dealership or aqualified technician.
Programming spareSecuriLockkeys
Spare SecuriLockkeys can bepurchased from your dealershipand programmed to yourSecuriLock anti-theft system (upto a total of 8 keys). Yourdealership can program your newSecuriLockkey(s) to yourvehicle or you can do it yourselfusing the following simpleprocedure. To program a newSecuriLockkey yourself, you willneed two previously programmedSecuriLockkeys (keys thatalready operate your vehiclesengine). If two previouslyprogrammed SecuriLockkeys arenot available (one or both of youroriginal keys were lost or stolen),
you must bring your vehicle toyour dealership to have the spareSecuriLockkey(s) programmed.
Procedure to program spareSecuriLockkeys to yourvehicle
New SecuriLockkeys must havethe correct mechanical key cut foryour vehicle.
Conventional (non-SecuriLock)keys cannot be programmed toyour vehicle.
You will need to have two
previously programmed
Controls and features
59
8/11/2019 98 Mountaineer
60/216
SecuriLockkeys and the newunprogrammed SecuriLockkeyreadily accessible for theprocedure. Please read andunderstand the entire procedurebefore you begin.
1. Insert the first previouslyprogrammed SecuriLockkey intothe ignition switch and turn theignition from OFF to RUN(maintain ignition in RUN for at
least one second).2. Turn ignition to OFF andremove the first SecuriLockkeyfrom the ignition switch.
3. Within five seconds of turningthe ignition to OFF, insert thesecond previously programmedSecuriLockkey into the ignitionswitch and turn the ignition fromOFF to RUN (maintain ignition inRUN for at least one second but nomore than 5 seconds).
4. Turn the ignition to OFF andremove the second SecuriLockkey from the ignition switch.
5. Within 10 seconds of turning theignition to OFF, insert theunprogrammed SecuriLockkey(new key) into the ignition switchand turn the ignition from OFF toRUN (maintain ignition switch inRUN for at least one second). Thisstep will program your newSecuriLockkey.
6. If it is desired to programadditional SecuriLockkey(s),repeat this procedure from step 1.
Controls and features
60
8/11/2019 98 Mountaineer
61/216
If the programming procedure wassuccessful, the new SecuriLockkey(s) will start the vehiclesengine. The theft indicator(located on the instrument cluster)will light for three seconds andthen go out.
If the programming procedure wasnot successful, the newSecuriLockkey(s) will notoperate the vehicles engine. The
theft indicator will flash on and off.Wait at least one minute and thenrepeat the procedure from step 1.If failure repeats, bring yourvehicle to your dealership to havethe spare SecuriLockkey(s)programmed.
Controls and features
61
8/11/2019 98 Mountaineer
62/216
SEATING
Head restraints
Push or pull the head rests to thedesired position.
Front seats
Never adjust the driversseat or seatback when the
vehicle is moving.
Do not pile cargo higherthan the seatbacks to
avoid injuring people in acollision or sudden stop.
Always drive and ride withyour seatback upright and
the lap belt snug and low acrossthe hips.
Seating and safety restraints
62
8/11/2019 98 Mountaineer
63/216
Lift handle to move seat forwardor backward.
Pull lever up to adjust seatback.
Adjusting the front power seat(if equipped)
Never adjust the driversseat or seatback when the
vehicle is moving.
Do not pile cargo higherthan the seatbacks to
avoid injuring people in acollision or sudden stop.
Always drive and ride withyour seatback upright and
the lap belt snug and low acrossthe hips.
Seating and safety restraints
63
8/11/2019 98 Mountaineer
64/216
Press to raise or lower the frontportion of the seat cushion.
Press to raise or lower the rearportion of the seat cushion.
Press the control to move the seatforward, backward, up or down.
Using the power lumbarsupport
The power lumbar control islocated on the outboard side of theseat.
Press one side of the control toadjust firmness.
Press the other side of the controlto adjust softness.
Seating and safety restraints
64
8/11/2019 98 Mountaineer
65/216
REAR SEATS
Head restraints
Push or pull the head rests to thedesired position.
Folding rear seats (if equipped)
If your vehicle is equipped with abuilt-in child seat, the seatbackcannot be folded down unless thebuilt-in child seat is fully stowed.
1. Press the lower release controldownward to unlatch the seatback.
2. Rotate the seatback downwardinto the load floor position.
3. Press down on the top outboardarea of the seatback until a click isheard. The seat is now latched inthe floor position. PUSH
PUSH
Seating and safety restraints
65
8/11/2019 98 Mountaineer
66/216
To return the seat to the uprightposition:
Press downward on the uppercorner of the seatback and hold.
Pull the release handle upwardto unlatch the seat.
Rotate the seatback upwarduntil the seatback latches in theupright position. The seatback
will click when it is locked intoposition.
SAFETY RESTRAINTS
Safety restraints precautions
Always drive and ride withyour seatback upright andthe lap belt snug and low acrossthe hips.
To prevent the risk ofinjury, make sure children
sit where they can be properlyrestrained.
PUSH
PUSH
Seating and safety restraints
66
8/11/2019 98 Mountaineer
67/216
Never let a passenger holda child on his or her lap
while the vehicle is moving. Thepassenger cannot protect thechild from injury in a collision.
All occupants of thevehicle, including the
driver, should always wear theirsafety belts.
It is extremely dangerousto ride in a cargo area,
inside or outside of a vehicle. Ina collision, people riding in theseareas are more likely to beseriously injured or killed. Do notallow people to ride in any areaof your vehicle that is notequipped with seats and safetybelts. Be sure everyone in yourvehicle is in a seat and using asafety belt properly.
Each seating position inyour vehicle has a specific
safety belt assembly which ismade up of one buckle and onetongue that are designed to beused as a pair. 1) Use theshoulder belt on the outsideshoulder only. Never wear theshoulder belt under the arm. 2)Never swing it around your neckover the inside shoulder. 3)Never use a single belt for morethan one person.
Seating and safety restraints
67
8/11/2019 98 Mountaineer
68/216
Combination lap and shoulderbelts
1. To fasten, insert the tongue intothe slot in the buckle.
2. To unfasten, push the redrelease button and remove thetongue from the buckle.
The front and rear outboard safetyrestraints in the vehicle arecombination lap and shoulderbelts. The front and rear seatpassenger outboard safety beltshave two types of locking modesdescribed below:
Vehicle sensitive mode
The vehicle sensitive mode is thenormal retractor mode, allowingfree shoulder belt lengthadjustment to your movements andlocking in response to vehiclemovement. For example, if thedriver brakes suddenly or turns a
corner sharply, or the vehicle
Seating and safety restraints
68
8/11/2019 98 Mountaineer
69/216
receives an impact of 8 km/h(5 mph) or more, the combinationsafety belts will lock to helpreduce forward movement of thedriver and passengers.
Automatic locking mode
In this mode, the shoulder belt isautomatically pre-locked. The beltwill still retract to remove anyslack in the shoulder belt.
The automatic locking mode is notavailable on the driver safety belt.
When to use the automaticlocking mode
When a tight lap/shoulder fit isdesired.
Anytime a child safety seat isinstalled in the vehicle. Refer toSafety Restraints for Childrenor Safety Seats for Childrenlater in this chapter.
How to use the automaticlocking mode
Buckle the combination lap andshoulder belt.
Seating and safety restraints
69
8/11/2019 98 Mountaineer
70/216
Grasp the shoulder portion andpull downward until the entirebelt is extracted.
Allow the belt to retract. As thebelt retracts, you will hear aclicking sound. This indicatesthe safety belt is now in theautomatic locking mode.
How to disengage the automaticlocking mode
Disconnect the combinationlap/shoulder belt and allow it toretract completely to disengage theautomatic locking mode andactivate the vehicle sensitive(emergency) locking mode.
Front safety belt heightadjustment
Your vehicle has safety belt heightadjustments for the driver andfront passenger. Adjust the heightof the shoulder belt so the beltrests across the middle of yourshoulder.
To lower the shoulder belt height,push the button and slide theheight control down. To raise theheight of the shoulder belt, slidethe height adjuster up. Pull down
on the height adjustment assembly
Seating and safety restraints
70
8/11/2019 98 Mountaineer
71/216
to make sure it is locked in place.
Position the shoulder beltheight adjuster so that the
belt rests across the middle ofyour shoulder. Failure to adjustthe safety belt properly couldreduce the effectiveness of thesafety belt and increase the riskof injury in a collision.
Safety belt extension assemblyIf the safety belt assembly is tooshort, even when fully extended,20 cm (8 inches) can be added tothe safety belt assembly by addinga safety belt extension assembly(part number 611C22). Safety beltextension assemblies can beobtained from your dealer at nocost.
Use only extensions manufacturedby the same supplier as the safetybelt. Manufacturer identification islocated at the end of the webbing
on the label. Also, use the safetybelt extension only if the safetybelt is too short for you when fullyextended. Do not use extensionsto change the fit of the shoulderbelt across the torso.
Safety belt warning light andindicator chime
The seat belt warning lightilluminates in the instrumentcluster and a chime sounds toremind the occupants to fastentheir safety belts.
Seating and safety restraints
71
8/11/2019 98 Mountaineer
72/216
Conditions of operation
If... Then...
The drivers safety belt is not
buckled before the ignition key
is turned to ON...
The safety belt warning light
illuminates for one to two minutes and
the warning chime sounds for four to
eight seconds.
The drivers safety belt is
buckled while the indicator
light is illuminated and the
warning chime is sounding...
The safety belt warning light turns off.
The drivers safety belt is
buckled before the ignition key
is turned to ON...
The safety belt warning light remains
off.
Safety belt maintenance
Check the safety belt systemsperiodically to make sure theywork properly and are notdamaged. Check the safety belts tomake sure there are no nicks,wears or cuts. All safety beltassemblies, including retractors,buckles, front seat belt buckleassemblies (slide bar)(ifequipped), shoulder belt heightadjusters (if equipped), childsafety seat tether bracketassemblies (if equipped), andattaching hardware, should beinspected after a collision. Fordrecommends that all safety beltassemblies used in vehiclesinvolved in a collision be replaced.However, if the collision was minorand a qualified technician findsthat the belts do not show damageand continue to operate properly,
they do not need to be replaced.
Seating and safety restraints
72
8/11/2019 98 Mountaineer
73/216
Safety belt assemblies not in useduring a collision should also beinspected and replaced if eitherdamage or improper operation isnoted.
Failure to replace thesafety belt assembly under
the above conditions could resultin severe personal injuries in theevent of a collision.
Refer to Cleaning andmaintaining the safety belts inthe Maintenance and caresection.
AIR BAG SUPPLEMENTALRESTRAINT SYSTEM (SRS)
0
1
2
3
45 6
H
C
F
E
OFF
OFF
REW1
FF2
SIDE1-2
3
FM 1
VOL PUSHON
AMFMBASSTREB
BAL FADEAUTOSET
CLK
SEEK
TUNEDISCS
SCAN
4
DOLBY SYSTEM
EJ TAPE CD
COMP5
SHUFFLE6
PUSH
20
10
30
40
5060 70
80
90
110
200
0 0 0 0 0 0
o o o o
10020
40
6080
100120
140
160
180
UNLEADEDFUELONLY
ODON/OFF
H
H
L
O FF O NR. WIPE
A/C
MAX
A/C
RSM
SETACC
COASTOFF
ON
SRS
Seating and safety restraints
73
8/11/2019 98 Mountaineer
74/216
Important supplementalrestraint system (SRS)precautions
The supplemental restraint systemis designed to:
work with the safety belt toprotect the driver and rightfront passenger
reduce certain upper body
injuries
Failure to follow theseinstructions will affect the
performance of the safety beltsand increase the risk of personalinjury.
The right front passenger
air bag is not designed torestrain occupants in the centerfront seating position.
All occupants of thevehicle including the driver
should always wear their safetybelts even when air bag SRS isprovided.
Seating and safety restraints
74
8/11/2019 98 Mountaineer
75/216
Do not place objects ormount equipment on or
near the air bag cover on thesteering wheel or in front seatareas that may come into contactwith a deploying air bag. Failureto follow this instruction mayincrease the risk of personalinjury in the event of a collision.
Do not attempt to service,repair, or modify the AirBag Supplemental RestraintSystem or its fuses. See yourFord or Lincoln-Mercury dealer.
Children and air bags
For additional important safetyinformation, read all informationon safety restraints in this guide.
Children should always wear theirsafety belts. Failure to follow these
instructions may increase the riskof injury in a collision.
Air bag can kill or injure achild in a child seat. If you
must use a forward-facing childseat in the front seat, move seatall the way back.
Seating and safety restraints
75
8/11/2019 98 Mountaineer
76/216
How does the air bagsupplemental restraint systemwork?
The SRS is designed to activatewhen the vehicle sustainssufficient longitudinal deceleration.
The fact that the air bags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere not of the type sufficient tocause activation.
The air bags inflate and deflaterapidly upon activation.
After air bag deployment, it isnormal to notice a smoke-like,powdery residue or smell the burntpropellant. This may consist ofcornstarch, talcum powder (tolubricate the bag) or sodiumcompounds (e.g., baking soda) that
result from the combustion processthat inflates the air bag. Smallamounts of sodium hydroxide maybe present which may irritate theskin and eyes, but none of theresidue is toxic.
Several air bag systemcomponents get hot after
inflation. Do not touch themafter inflation.
Seating and safety restraints
76
8/11/2019 98 Mountaineer
77/216
8/11/2019 98 Mountaineer
78/216
A difficulty with the system isindicated by one or more of thefollowing:
The readiness light will eitherflash or stay lit.
The readiness light will notilluminate immediately afterignition is turned on.
A series of five beeps will be
heard. The tone pattern willrepeat periodically until theproblem and light are repaired.
If any of these things happen, evenintermittently, have the SRSserviced at your dealership or by aqualified technician immediately.Unless serviced, the system maynot function properly in the eventof a collision.
Disposal of air bags and air bagequipped vehicles
For disposal of air bags or air bag
equipped vehicles, see your localdealership or qualified technician.Air bags MUST BE disposed of byqualified personnel.
SAFETY RESTRAINTS FORCHILDREN
Important child restraintprecautions
You are required by law to usesafety restraints for children in theU.S. and Canada. If small childrenride in your vehicle (generallychildren who are four years old or
Seating and safety restraints
78
8/11/2019 98 Mountaineer
79/216
younger and who weigh 18 kg[40 lbs] or less), you must putthem in safety seats madeespecially for children. Check yourlocal and state or provincial lawsfor specific requirements regardingthe safety of children in yourvehicle.
Never let a passenger holda child on his or her lap
while the vehicle is moving. The
passenger cannot protect thechild from injury in a collision.
Always follow the instructions andwarnings that come with any infantor child restraint you might use.
When possible, place children inthe rear seat of your vehicle.Accident statistics suggest thatchildren are safer when properlyrestrained in the rear seatingpositions than in the front seatingposition.
Children and safety belts
Children who are too large forchild safety seats (as specified byyour child safety seatmanufacturer) should always wearsafety belts.
Follow all the important safetyrestraint and air bag precautionsthat apply to adult passengers inyour vehicle.
If the shoulder belt portion of acombination lap and shoulder beltcan be positioned so it does not
cross or rest in front of the childs
Seating and safety restraints
79
8/11/2019 98 Mountaineer
80/216
face or neck, the child should wearthe lap and shoulder belt. Movingthe child closer to the center ofthe vehicle may help provide agood shoulder belt fit.
If the shoulder belt cannot beproperly positioned:
move the child to one of theseats with a lap belt only (ifequipped)
OR
if the child is the proper size,restrain the child in a safetyseat.
Do not leave children,unreliable adults, or pets
unattended in your vehicle.
To improve the fit of lap andshoulder belts on children whohave outgrown child safety seats,Ford recommends use of abelt-positioning booster seat that islabelled as conforming to allFederal motor vehicle safetystandards. Belt-positioning boosterseats raise the child and provide ashorter, firmer seating cushion thatencourages safer seating postureand better fit of lap and shoulderbelts on the child. Abelt-positioning booster should beused if the shoulder belt rests infront of the childs face or neck, orif the lap belt does not fit snuglyon both thighs, or if the thighs aretoo short to let the child sit all theway back on the seat cushion
when the lower legs hang over the
Seating and safety restraints
80
8/11/2019 98 Mountaineer
81/216
edge of the seat cushion. You maywish to discuss the special needsof your child with yourpediatrician.
SAFETY SEATS FOR CHILDREN
Child and infant or child safetyseats
Use a safety seat that isrecommended for the size andweight of the child. Carefullyfollow all of the manufacturersinstructions with the safety seatyou put in your vehicle. If you donot install and use the safety seatproperly, the child may be injuredin a sudden stop or collision.
When installing a child safety seat:
Use the correct safety beltbuckle for that seating position.
Make sure the tongue issecurely fastened in the buckle.
Keep the buckle release buttonpointing up and away from thesafety seat, with the tonguebetween the child seat and therelease button, to preventaccidental unbuckling.
Place seat back in uprightposition.
Put the safety belt in theautomatic locking mode. Referto Automatic locking mode.
Ford recommends the use of achild safety seat having a toptether strap. Install the child safety
seat in a seating position which is
Seating and safety restraints
81
8/11/2019 98 Mountaineer
82/216
capable of providing a tetheranchorage. For more informationon top tether straps, refer toAttaching safety seats with tetherstraps.
Carefully follow all of themanufacturers instructions
included with the safety seat youput in your vehicle. If you do notinstall and use the safety seatproperly, the child may be
injured in a sudden stop orcollision.
Installing child safety seats incombination lap and shoulderbelt seating positions
1. Position the child safety seat ina seat with a combination lap andshoulder belt.
Air bag can kill or injure achild in a child seat. If you
must use a forward-facing childseat in the front seat, move seatall the way back.
Seating and safety restraints
82
8/11/2019 98 Mountaineer
83/216
2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.
3. While holding the shoulder andlap belt portions together, routethe tongue through the child seataccording to the child seatmanufacturers instructions. Besure the belt webbing is nottwisted.
4. Insert the belt tongue into theproper buckle for that seatingposition until you hear and feel the
latch engage. Make sure thetongue is latched securely bypulling on it.
Seating and safety restraints
83
8/11/2019 98 Mountaineer
84/216
5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt andpull downward until all of the beltis extracted and a click is heard.
6. Allow the belt to retract. Thebelt will click as it retracts toindicate it is in the automaticlocking mode.
7. Pull the lap belt portion acrossthe child seat toward the buckleand pull up on the shoulder beltwhile pushing down with knee onthe child seat.
8. Allow the safety belt to retractto remove any slack in the belt.
9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make sure the seat issecurely held in place.
10. Try to pull the belt out of theretractor to make sure theretractor is in the automatic
locking mode (you should not be
Seating and safety restraints
84
8/11/2019 98 Mountaineer
85/216
able to pull more belt out). If theretractor is not locked, unbucklethe belt and repeat steps twothrough nine.
Check to make sure the child seatis properly secured before eachuse.
Attaching safety seats withtether straps
Some manufacturers make safety
seats that include a tether strapthat goes over the back of thevehicle seat and attaches to ananchoring point. Othermanufacturers offer the tetherstrap as an accessory. Contact themanufacturer of your child safetyseat for information about orderinga tether strap.
Tether anchorage hardware
A tethered seat can be installed inthe front seat. Put the tether strapover the seatback and attach it to
a anchor bracket.An anchor bracket can be installedon the rear edge of the front seatcushion.
The provision (attaching hole) isprovided in the rear edge of thefront passenger seat cushionframe. The anchorbracket must beinstalled using the instructionsprovided with the kit.
Tether anchorage hardware kits(part number 613D74) includinginstructions, may be obtained at nocharge from any Ford or
Lincoln-Mercury dealer.
Seating and safety restraints
85
8/11/2019 98 Mountaineer
86/216
Tighten the anchoraccording to specifications.
Otherwise, the safety seat maynot be properly secured and thechild may be injured in a suddenstop or collision.
BUILT-IN CHILD SEATS
Built-in child safety seat(if equipped)
The rear seat may include abuilt-in child seat. This child seatconforms to all Federal and localmotor vehicle safety standard.Read the labels located on thechild seat cushion and shoulderbelt for information on the built-inchild seat.
Use the built-in child seat only ifthe child is at least 9 months old,weighs 929 kg (2060 lb) and thechilds shoulders (top) are belowthe shoulder harness slots in the
built-in child seat.Children not meeting theserequirements should be secured inan approved aftermarket seat.Refer to Children and infant orchild safety seats in this chapter.
Seating and safety restraints
86
8/11/2019 98 Mountaineer
87/216
Placing your child in the built-inchild seat
Failure to follow all of theinstructions on the use of
this child restraint system canresult in your child striking thevehicles interior during a suddenstop or crash.
The second row seatback
must be fully locked beforeoperating the child restraintsystem. Check the position of theseatback release lever.
Never use the Built-InChild Seat as a booster
cushion with the adult safetybelts. A child using the adultbelts could slide forward and outfrom under the safety belts.
1. Grasp the strap and pull towardyou approximately 25 mm (1 inch),then slide hand under the headrestraint and slide upwards to thefull position.
Seating and safety restraints
87
8/11/2019 98 Mountaineer
88/216
2. Pull both Velcro straps torelease the child seat cushion.
3. Lower the child seat cushion.
Seating and safety restraints
88
8/11/2019 98 Mountaineer
89/216
4. Unfold the cushion protectorflap onto adult seat cushion
5. If connected, disconnect thechest clip and buckles.
6. Place the child in the seat andposition the left shoulder belt overthe childs left shoulder first, thenplace the right shoulder belt overthe childs right shoulder
Seating and safety restraints
89
8/11/2019 98 Mountaineer
90/216
7. Insert the left and right safetybelt tongues into the left and rightslots of the crotch buckle. Verifythat the indicator window on eachtongue is green to ensure propersafety belt connections.
If both tongues do notlatch in the buckle, do not
use the child seat. See yourdealer for repairs.
8. Fasten the right and left chestclip halves together and adjust theclip to comfortably hold the
shoulder belts in place over thechilds chest.
The chest clip is designed to easilypull apart in a collision. The cliphelps to keep belts snug on asleeping or squirming child.
Seating and safety restraints
90
8/11/2019 98 Mountaineer
91/216
9. Pull on the safety belt tonguesto ensure that they are bothsecurely latched. If they are notproperly latched, repeat stepsseven and eight.
If necessary, the shoulder belt maybe put in automatic locking mode(ALR) to limit the childsmovement in the seat. The ALRmode should be used if the child issleeping or attempting to get outof the seat.
If not placed in ALR mode, thechild seat shoulder belts are invehicle sensitive (emergencylocking) mode, which allow somemovement of the shoulder belts(like adult shoulder belts).
In emergency locking mode, the
shoulder belts of the child seat willlock in response to hard braking,hard cornering or if your vehicle isinvolved in a collision with animpact of 8 km/h (5 m.p.h.) ormore.
Activating the automatic lockingmode (ALR) on the built-in childsafety seat
1. Fully extend the right shoulderbelt.
2. Allow the belts to tighten snuglyagainst the childs shoulders
Seating and safety restraints
91
8/11/2019 98 Mountaineer
92/216
Deactivating the automaticlocking mode (ALR) on thebuilt-in child safety seat
1. Disconnect the chest clip andremove the left and right safetybelt tongues from the crotchbuckle.
2. Allow the shoulder belts to fullyretract.
Removing your child from the
built-in child safety seat
1. Disconnect the chest clip bysqueezing the release tabs togetherand pulling the two sides apart.
2. Press the release button on thecrotch buckle.
3. Slide the shoulder belts off thechilds shoulders and remove thechild from the seat.
If ALR is activated, hold either theleft or right shoulder belt out fullywhile helping the child slide armsout of the belts.
4. Fold the cushion protector flaponto the child seat cushion. Slidethe belt tongues up and out of theway of the cushion, then returnthe child seat cushion to thestowed (upright) position.
Seating and safety restraints
92
8/11/2019 98 Mountaineer
93/216
5. Slide the Velcro straps throughthe D-rings on the child seatcushion and attach.
6. Slide the head restraint downuntil the top of the head restraintis flush with the top of the adultseat back.
7. Press firmly on the top center ofthe built-in child safety seat headrestraint to ensure it is stowedproperly.
Inspecting the built-in child seatafter a collision
Inspect all built-in child restraints,including seats, buckles, retractors,seat latches. Interlocks andattaching hardware should beinspected by a qualified technicianafter any collision. If the child seatwas in use during a collision, Fordrecommends replacing it. Built-inchild restraints not in use during acollision should be inspected andreplaced if either damage orimproper operation is noted.
Seating and safety restraints
93
8/11/2019 98 Mountaineer
94/216
PREPARING TO START YOURVEHICLE
Engine starting is controlled by thespark ignition system. This systemmeets all CanadianInterference-Causing Equipmentstandard requirements regulatingthe impulse electrical field strengthof radio noise.
When starting a fuel-injectedengine, avoid pressing the
accelerator before or duringstarting. Only use the acceleratorwhen you have difficulty startingthe engine. For more informationon starting the vehicle, refer toStarting the enginein thischapter.
Extended idling at highengine speeds can produce
very high temperatures in theengine and exhaust system,creating the risk of fire or otherdamage.
Do not park, idle, or driveyour vehicle in dry grass
or other dry ground cover. Theemission system heats up theengine compartment and exhaustsystem, which can start a fire.
Starting
94
8/11/2019 98 Mountaineer
95/216
Do not start your vehiclein a closed garage or in
other enclosed areas. Exhaustfumes can be toxic. Always openthe garage door before you startthe engine. See Guardingagainst exhaust fumes in thischapter for more instructions.
If you smell exhaust fumes
inside your vehicle, haveyour dealer inspect your vehicleimmediately. Do not drive if yousmell exhaust fumes.
Important safety precautions
A computer system controls theengines idle revolutions perminute (RPM). When the enginestarts, the idle RPM runs faster towarm the engine. If the engine idlespeed does not slow downautomatically, have the vehiclechecked.
Before starting the vehicle:
1. Make sure all vehicle occupantshave buckled their safety belts. Formore information on safety beltsand their proper usage, refer tothe Seating and safety restraintschapter.
2. Make sure the headlamps andvehicle accessories are off.
Starting
95
8/11/2019 98 Mountaineer
96/216
8/11/2019 98 Mountaineer
97/216
Make sure the corresponding lightsilluminate briefly. If a light fails toilluminate, have the vehicleserviced.
If the drivers safety belt isfastened, the light ( ) will notilluminate.
STARTING THE ENGINE
1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will returnto 4 (ON).
2. If the engine does not startwithin five seconds, wait tenseconds and try again.
3. If the engine does not start intwo attempts OR if the
temperature is below -12C (10F),depress the accelerator and startthe engine while holding theaccelerator down. Release theaccelerator when the engine starts.
4. After idling for a few seconds,apply the brake and release theparking brake.
Using the engine block heater(if equipped)
An engine block heater warms theengine coolant, which improvesstarting, warms up the engine
faster and allows the
3
2
1
5
4
Starting
97
8/11/2019 98 Mountaineer
98/216
heater-defroster system to respondquickly. They are stronglyrecommended if you live in aregion where temperatures reach-23C (-10F) or below.
For best results, plug the heater inat least three hours before startingthe vehicle. Using the heater forlonger than three hours will notharm the engine, so the heater canbe plugged in the night before
starting the vehicle.
To prevent electricalshock, do not use your
heater with ungroundedelectrical systems ortwo-pronged (cheater) adapters.
Guarding against exhaustfumes
Although odorless and colorless,carbon monoxide is present inexhaust fumes. Take precautionsto avoid its dangerous effects.
If you ever smell exhaustfumes of any kind inside
your vehicle, have your dealerinspect and fix your vehicleimmediately. Do not drive if yousmell exhaust fumes. Thesefumes are harmful and could killyou.
Have the exhaust and bodyventilation systems checkedwhenever:
the vehicle is raised for service
Starting
98
8/11/2019 98 Mountaineer
99/216
the sound of the exhaust systemchanges
the vehicle has been damaged ina collision
Important ventilatinginformation
If the engine is idling while thevehicle is stopped in an open areafor long periods of time, open thewindows at least 2.5 cm (one
inch).Adjust the heating or airconditioning (if equipped) to bringin fresh air.
Improve vehicle ventilation bykeeping all air inlet vents clear ofsnow, leaves and other debris.
Starting
99
8/11/2019 98 Mountaineer
100/216
BRAKES
Your brakes are self-adjusting.Refer to the Service Guide forscheduled maintenance.
Occasional brake noise is normaland often does not indicate aperformance concern with thevehicles brake system. In normaloperation, automotive brakesystems may emit occasional orintermittent squeal or groan noises
when the brakes are applied. Suchnoises are usually heard during thefirst few brake applications in themorning; however, they may beheard at any time while brakingand can be aggravated byenvironmental conditions such ascold, heat, moisture, road dust, saltor mud. If a metal-to-metal,continuous grinding orcontinuous squeal sound ispresent while braking, the brakelinings may be worn-out andshould be inspected by a qualified
service technician.Anti-lock brake system (ABS)
On vehicles equipped with ananti-lock braking system (ABS), anoise from the hydraulic pumpmotor and pulsation in the pedalmay be observed during ABSbraking events. Pedal pulsationcoupled with noise while brakingunder panic conditions or on loosegravel, bumps, wet or snowy roadsis normal and indicates properfunctioning of the vehiclesanti-lock brake system. If the
vehicle has continuous vibration or
Driving
100
8/11/2019 98 Mountaineer
101/216
shudder while braking, felt mainlyin the steering wheel, the vehiclemost likely n