Download pdf - 42CS669C

7/23/2019 42CS669C

1/41

LCD TV

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : LD0AW

MODEL : 42CS669C 42CS669C-ZD

North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com

Internal Use Only

Printed in KoreaP/NO : MFL67180609 (1207-REV00)

7/23/2019 42CS669C

2/41

LGE Internal Use OnlyCopyright 2012 LG Electronics. Inc. All right reserved.

Only for training and service purposes

- 2 -

CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ..................................................................................3

SPECIFICATION........................................................................................6

ADJUSTMENT INSTRUCTION .................................................................9

TROUBLE SHOOTING............................................................................14

BLOCK DIAGRAM...................................................................................22

EXPLODED VIEW .................................................................................. 23

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

7/23/2019 42CS669C

3/41



- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the

Schematic Diagram and Exploded View.

It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent

Shock, Fire, or other Hazards.Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the

servicing of a receiver whose chassis is not isolated from the AC

power line. Use a transformer of adequate power rating as this

protects the technician from accidents resulting in personal injury

from electrical shocks.

It will also protect the receiver and it's components from being

damaged by accidental shorts of the circuitry that may be

inadvertently introduced during the service operation.

If any fuse(or Fusible Resistor) in this TV receiver is blown, replace

it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor,

over 1 W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to

be sure the set is safe to operate without damage of electrical

shock.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an

electrical jumper across the two AC plug prongs. Place the AC

switch in the on position, connect one lead of ohm-meter to the AC

plug prongs tied together and touch other ohm-meter lead in turn to

each exposed metallic parts such as antenna terminals, phone

jacks, etc.

If the exposed metallic part has a return path to the chassis, the

measured resistance should be between 1 M and 5.2 M.

When the exposed metal has no return path to the chassis the

reading must be infinite.

An other abnormality exists that must be corrected before the

receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor

between a known good earth ground (Water Pipe, Conduit, etc.)

and the exposed metallic parts.

Measure the AC voltage across the resistor using AC voltmeter

with 1000 ohms/volt or more sensitivity.

Reverse plug the AC cord into the AC outlet and repeat AC voltage

measurements for each exposed metallic part. Any voltage

measured must not exceed 0.75 volt RMS which is corresponds to0.5 mA.

In case any measurement is out of the limits specified, there is

possibility of shock hazard and the set must be checked and

repaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instruments

exposed

METALLIC PARTS

Good Earth Ground

such as WATER PIPE,CONDUIT etc.

AC Volt-meter

When 25A is impressed between Earth and 2nd Ground

for 1 second, Resistance must be less than 0.1

*Base on Adjustment standard

IMPORTANT SAFETY NOTICE

0.15 uF

7/23/2019 42CS669C

4/41



- 4 -

CAUTION: Before servicing receivers covered by this service

manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONSon page 3 of this publication.

NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on

page 3 of this publication, always follow the safety precautions.

Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power

source before;

a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.

CAUTION: A wrong part substitution or incorrect polarity

installation of electrolytic capacitors may result in an

explosion hazard.

2. Test high voltage only by measuring it with an appropriate high

voltage meter or other voltage measuring device (DVM,

FETVOM, etc) equipped with a suitable high voltage probe.

Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its

assemblies.

4. Unless specified otherwise in this service manual, clean

electrical contacts only by applying the following mixture to the

contacts with a pipe cleaner, cotton-tipped stick or comparable

non-abrasive applicator; 10 % (by volume) Acetone and 90 %

(by volume) isopropyl alcohol (90 % - 99 % strength)

CAUTION: This is a flammable mixture.

Unless specified otherwise in this service manual, lubrication of

contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which

receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of itselectrical assemblies unless all solid-state device heat sinks are

correctly installed.

7. Always connect the test receiver ground lead to the receiver

chassis ground before connecting the test receiver positive

lead.

Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any

heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily

by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ESdevices are integrated circuits and some field-effect transistors and

semiconductor chip components. The following techniques

should be used to help reduce the incidence of component

damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic

charge on your body by touching a known earth ground.

Alternatively, obtain and wear a commercially available

discharging wrist strap device, which should be removed to

prevent potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES

devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or

exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES

devices.

4. Use only an anti-static type solder removal device. Some solder

removal devices not classified as anti-static can generate

electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate

electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective

package until immediately before you are ready to install it.

(Most replacement ES devices are packaged with leads

electrically shorted together by conductive foam, aluminum foil

or comparable conductive material).

7. Immediately before removing the protective material from the

leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be

installed.

CAUTION: Be sure no power is applied to the chassis or circuit,

and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged

replacement ES devices. (Otherwise harmless motion such as

the brushing together of your clothes fabric or the lifting of your

foot from a carpeted floor can generate static electricity

sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate

tip size and shape that will maintain tip temperature within the

range or 500 F to 600 F.2. Use an appropriate gauge of RMA resin-core solder composed

of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wire-

bristle (0.5 inch, or 1.25 cm) brush with a metal handle.Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 F to 600 F)b. Heat the component lead until the solder melts.

c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique.

a. Allow the soldering iron tip to reach a normal temperature

(500 F to 600 F)b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of thecomponent lead and the printed circuit foil, and hold it there

only unti l the solder f lows onto and around both the

component lead and the foil.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS

7/23/2019 42CS669C

5/41



- 5 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through

which the IC leads are inserted and then bent flat against the

circuit foil. When holes are the slotted type, the following technique

should be used to remove and replace the IC. When working with

boards using the familiar round hole, use the standard technique

as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gentlyprying up on the lead with the soldering iron tip as the solder

melts.

2. Draw away the melted solder with an anti-static suction-type

solder removal device (or with solder braid) before removing the

IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and

solder it.

3. Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor

Removal/Replacement

1. Remove the defective transistor by clipping its leads as close aspossible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining

on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" with

long nose pliers to insure metal to metal contact then solder

each connection.

Power Output, Transistor Device

Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit

board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as

possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit

board.

3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and if

necessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow

stake.

2. Securely crimp the leads of replacement component around

notch at stake top.

3. Solder the connections.

CAUTION: Maintain original spacing between the replaced

component and adjacent components and the circuit board to

prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit

board will weaken the adhesive that bonds the foil to the circuit

board causing the foil to separate from or "lift-off" the board. The

following guidelines and procedures should be followed whenever

this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the

following procedure to install a jumper wire on the copper patternside of the circuit board. (Use this technique only on IC

connections).

1. Carefully remove the damaged copper pattern with a sharp

knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if

used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and

carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper

pattern and let it overlap the previously scraped end of the good

copper pattern. Solder the overlapped area and clip off any

excess jumper wire.

At Other ConnectionsUse the following technique to repair the defective copper pattern

at connections other than IC Pins. This technique involves the

installation of a jumper wire on the component side of the circuit

board.

1. Remove the defective copper pattern with a sharp knife.

Remove at least 1/4 inch of copper, to ensure that a hazardous

condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern

break and locate the nearest component that is directly

connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the

nearest component on one side of the pattern break to the lead

of the nearest component on the other side.

Carefully crimp and solder the connections.

CAUTION: Be sure the insulated jumper wire is dressed so the

it does not touch components or sharp edges.

7/23/2019 42CS669C

6/41



- 6 -

SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.

1. Application rangeThis specification is applied to the LCD TV used LD0AWchassis.

2. Requirement for TestEach part is tested as below without special appointment.

1) Temperature: 25 C 5 C(77 F 9 F), CST: 40 C 5 C2) Relative Humidity : 65 % 10 %3) Power Voltage

: Standard input voltage(100 V - 240 V, 50 / 60Hz)* Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followedeach drawing and specif ication by part number inaccordance with BOM.

5) The receiver must be operated for about 5 minutes prior tothe adjustment.

3. Test method1) Performance: LGE TV test method followed2) Demanded other specification

- Safety: CE, IEC specification

- EMC:CE, IEC

4. Model General SpecificationNo. Item Specification Remarks

1 Market EU(PAL Market - 36 countries) DTV-T/C & Analog

Germany, Netherlands, Switzerland, Hungary, Austria, Slovenia, Sweden, Denmark,

Finland, Norway, Bulgaria

DTV-T & Analog

UK, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia,Turkey,

Morocco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Ukraine, Slovakia

Analog Only

Kazakhstan, Albania, Bosnia, Serbia

2 Broadcasting system 1) PAL-BG

2) PAL-DK3) PAL-I/I

4) SECAM L/L

5) DVB-T/C/S (ID TV)

3 Receiving system Analog : Upper Heterodyne

Digital : COFDM, QAM

4 Scart Jack (1EA) PAL, SECAM Scart Jack is Full scart and support RF-OUT(analog)

5 Video Input RCA(1EA) PAL, SECAM, NTSC 4System : PAL, SECAM, NTSC, PAL60

6 Component Input(1EA) Y/Cb/Cr, Y/Pb/Pr

7 RGB Input RGB-PC Analog(D-SUB 15PIN)

8 HDMI Input (3EA) HDMI1-DTV (DVI) PC(HDMI version 1.3)

HDMI2-DTV Support HDCP

HDMI3-DTV Input port is different by model

9 Audio Input (3EA) RGB/DVI Audio, Component, AV L/R Input

10 SDPIF out (1EA) SPDIF out

11 Earphone out (1EA) Antenna, AV1, AV2, AV3, Component,

RGB, HDMI1, HDMI2, HDMI3

12 USB (1EA) For Service (download)

DivX

13 DVB DVB-T CI : UK, Finland, Denmark, Norway, Sweden, Russia, Spain, Ireland, Luxemburg, Belgium, Netherland

CI+ : France(Canal+), Italy(DGTVi)

DVB-C CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria

CI+ : Switzerland(UPC,Cablecom), Netherland(Ziggo), Germany(KDG,CWB), Finland(labwise)

DVB-S CI+ : Germany(Astra HD+)

7/23/2019 42CS669C

7/41

- 7 - LGE Internal Use OnlyCopyright 2012 LG Electronics. Inc. All right reserved.


5. Component Video Input (Y, CB/PB, CR/PR)

No.Specification

RemarkResolution H-freq(kHz) V-freq(Hz)

1. 720x480 15.73 60.00 SDTV,DVD 480i

2. 720x480 15.63 59.94 SDTV,DVD 480i

3. 720x480 31.47 59.94 480p

4. 720x480 31.50 60.00 480p

5. 720x576 15.625 50.00 SDTV,DVD 625 Line

6. 720x576 31.25 50.00 HDTV 576p

7. 1280x720 45.00 50.00 HDTV 720p

8. 1280x720 44.96 59.94 HDTV 720p

9. 1280x720 45.00 60.00 HDTV 720p

10. 1920x1080 31.25 50.00 HDTV 1080i

11. 1920x1080 33.75 60.00 HDTV 1080i

12. 1920x1080 33.72 59.94 HDTV 1080i

13. 1920x1080 56.250 50 HDTV 1080p

14. 1920x1080 67.5 60 HDTV 1080p

No.Specification

Proposed RemarkResolution H-freq(kHz) V-freq(Hz) Pixel Clock(MHz)

1. 720*400 31.468 70.08 28.321 For only DOS mode

2. 640*480 31.469 59.94 25.17 VESA Input 848*480 60 Hz, 852*480 60 Hz

-> 640*480 60 Hz Display

3. 800*600 37.879 60.31 40.00 VESA

4. 1024*768 48.363 60.00 65.00 VESA(XGA)5. 1360*768 47.72 59.8 84.75 WXGA FHD model

6. 1280*1024 63.981 60.02 108.875 SXGA FHD model

7. 1920*1080 67.5 60 148.5 WUXGA FHD model

6. RGB Input (PC)

7/23/2019 42CS669C

8/41



7. HDMI Input (PC/DTV)(1) DTV Mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1. 720*400 31.468 70.08 28.321 HDCP

2. 640*480 31.469 59.94 25.17 VESA HDCP

3. 800*600 37.879 60.31 40.00 VESA HDCP

4. 1024*768 48.363 60.00 65.00 VESA(XGA) HDCP

5. 1360*768 47.72 59.8 84.75 WXGA HDCP

6. 1280*720 45 60 74.25 HDCP

7. 1280*1024 63.595 60.02 108.875 SXGA HDCP / FHD model

8. 1920*1080 67.5 60 148.5 WUXGA HDCP / FHD model

(2) PC Mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1. 720*480 31.469 / 31.5 59.94 / 60 27.00 / 27.03 SDTV 480P

2. 720*576 31.25 50 54 SDTV 576P

3. 1280*720 37.500 50 74.25 HDTV 720P

4. 1280*720 44.96 / 45 59.94 / 60 74.17 / 74.25 HDTV 720P

5. 1920*1080 33.72 / 33.75 59.94 / 60 74.17 / 74.25 HDTV 1080I

6. 1920*1080 28.125 50.00 74.25 HDTV 1080I

7. 1920*1080 26.97 / 27 23.97 / 24 74.17 / 74.25 HDTV 1080P

8. 1920*1080 33.716 / 33.75 29.976 / 30.00 74.25 HDTV 1080P

9. 1920*1080 56.250 50 148.5 HDTV 1080P

10. 1920*1080 67.43 / 67.5 59.94 / 60 148.35 / 148.50 HDTV 1080P

7/23/2019 42CS669C

9/41

7/23/2019 42CS669C

10/41

* After downloading, have to adjust Tool Option again.(1) Push IN-START key in service manual control.(2) Select Tool Option 1 and push OK key.(3) Punch in the number. (Each models has their number.)(4) Correction Tool option is completed.

3.1. ADC Process Enter EZ ADJUST mode by pushing ADJ key,

Enter Internal ADC mode by pushing G

key at 7. ADCCalibration.

Using P-ONLY key of the Adjustment remotecontrol, power on TV.

* ADC Calibration Protocol (RS232)

Adjust Sequence aa 00 00 [Enter Adjust Mode] xb 00 40 [Component1 Input (480i)] ad 00 10 [Adjust 480i Comp1] xb 00 60 [RGB Input (1024*768)] ad 00 10 [Adjust 1024*768 RGB]

aa 00 90 End Adjust mode* Required equipment : Adjustment Remote control

3.2. EDID Download1) After Enter Service Mode by pushing ADJ key,2) Enter EDID D/L mode.3) Enter START by pushing OK key.

Never connect HDMI & D-sub cable when EDIDdownload

3.3. EDID data(1) FHD RGB EDID data

(2) FHD HDMI EDID data

(3) Detail EDID Options are belowa. Product ID

b. Serial No: Controlled on production line.c. Month, Year:

Week : 01 -> 01Year : 2011 -> 15 fixd. Model Name(Hex):

e. Checksum: Changeable by total EDID data.

f. Vendor Specific(HDMI)



ADC Calibration

ADC Comp 480i NG

ADC Comp 1080p NG

ADC RGB NG

Start Reset

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Country Group

6. Area Option

7. ADC Calibration

8. White Balance

9. 10 Point WB

10. Test Pattern

11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Setting

No Item CMD1 CMD2 Data0

Enter Adjust Adjust A A 0 0 When transfer the Mode In,

Mode Mode In Carry the command.

ADC adjust ADC Adjust A D 1 0 Automatically adjustment

(The use of a internal pattern)

HDMI1 OK

HDMI2 OK

HDMI3 OK

RGB OK

Start Reset

EDID D/L

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Country Group

6. Area Option

7. ADC Calibration

8. White Balance

9. 10 Point WB

10. Test Pattern11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Setting

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D a b

10 c 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26

20 0F 50 54 A1 08 00 71 4F 81 80 01 01 01 01 01 01

30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

40 45 00 A0 5A 00 00 00 1E 1B 21 50 A0 51 00 1E 30

50 48 88 35 00 A0 5A 00 00 00 1C 00 00 00 FD 00 3A

60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d

70 d 01 e

80 02 03 26 F1 4E 10 1F 84 13 05 14 03 02 12 20 21

90 22 15 01 26 15 07 50 09 57 07 f

A0 f E3 05 03 01 01 1D 80 18 71 1C 16 20 58 2C

B0 25 00 A0 5A 00 00 00 9E 01 1D 00 72 51 D0 1E 20

C0 6E 28 55 00 A0 5A 00 00 00 1E 02 3A 80 18 71 38

D0 2D 40 58 2C 45 00 A0 5A 00 00 00 1E 01 1D 00 BC

E0 52 D0 1E 20 B8 28 55 40 A0 5A 00 00 00 1E 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D a b

10 c 01 03 68 10 09 78 0A EE 91 A3 54 4C 99 26

20 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01

30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30

50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d

70 d 00 e

Model Name HEX EDID Table DDC Function

HD/FHD Model 0001 01 00 Analog/Digital

MODEL MODEL NAME(HEX)

LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20

EDID C/S data FHD HD

HDMI RGB HDMI RGB

Check sum Block 0 E2 ED B4 CD

(Hex) 99(HDMI1) 75(HDMI1)

Block 1 89(HDMI2) 65(HDMI2)

79(HDMI3) 55(HDMI3)

INPUT MODEL NAME(HEX)

HDMI1 67030C001000B82D

HDMI2 67030C002000B82D

HDMI3 67030C003000B82D

7/23/2019 42CS669C

11/41

3.4. Function Check(1) Check display and sound

- Check Input and Signal items. (cf. work instructions)1) TV2) AV3) COMPONENT1/2 (480i)4) RGB (PC : 1024 x 768 @ 60hz)5) HDMI6) PC Audio In

* Display and Sound check is executed by remote control.

Not to push the INSTOP key after completion if thefunction inspection.

4. Total Assembly line process4.1. Adjustment Preparation

W/B Equipment conditionCA210- CCFL/EEFL -> CH 9, Test signal : Inner pattern(80 IRE)- LED -> CH 14, Test signal : Inner pattern(80 IRE)

Above 5 minutes H/run in the inner pattern. (power on key

of adjustment remote control)

* Connecting picture of the measuring instrument(On Automatic control)Inside PATTERN is used when W/B is controlled. Connect toauto controller or push Adjustment R/C POWER ON -> Enter

the mode of White-Balance, the pattern will come out.

* Auto-control interface and directions1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).2) Adhere closely the Color Analyzer (CA210) to the module

less than 10cm distance, keep it with the surface of theModule and Color Analyzers Prove vertically.(80 ~ 100).

3) Aging time- After aging start, keep the power on (no suspension of

power supply) and heat-run over 15minutes.- Using no signal or full white pattern or the others, check

the back light on.

Auto adjustment Map(RS-232C)RS-232C COMMAND[CMD ID DATA]

Wb 00 00 White Balance StartWb 00 ff White Balance End

** Caution **Color Temperature : COOL, Medium, Warm.One of R Gain/G Gain/ B Gain should be kept on 0xC0, andadjust other two lower than C0.(when R/G/B Gain are all C0, it is the FULL Dynamic Range

of Module)

* Manual W/B process using adjusts Remote control. After enter Service Mode by pushing ADJ key,

Enter White Balance by pushing G key at 8. WhiteBalance.

* After done all adjustments, Press In-start key andcompare Tool option and Area option value with its BOM, ifit is correctly same then unplug the AC cable. If it is notsame, then correct it same with BOM and unplug AC cable.For correct it to the models module from factory Jig model.

* Push the IN STOP key after completing the function

inspection. And Mechanical Power Switch must be set ON.



Cool 13,000 K X=0.269(0.002)

Y=0.273(0.002)

Medium 9,300 K X=0.285(0.002) Inner pattern

Y=0.293(0.002) (204 gray,80 IRE)

Warm 6,500 K X=0.313(0.002)

Y=0.329(0.002)

RS-232C COMMAND MIN CENTER MAX

[CMD ID DATA] (DEFAULT)

Cool Mid Warm Cool Mid Warm

R Gain jg Ja jd 00 172 192 192 192

G Gain jh Jb je 00 172 192 192 192

B Gain j i Jc jf 00 192 192 172 192

R Cut 64 64 64 128

G Cut 64 64 64 128

B Cut 64 64 64 128

White Balance

Color Temp. Cool

R-Gain 172

G-Gain 172

B-Gain 192

R-Cut 64

G-Cut 64

B-Cut 64

Test-Pattern

Backlight

ON

100

Reset To Set

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Country Group

6. Area Option

7. ADC Calibration

8. White Balance

9. 10 Point WB

10. Test Pattern

11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Settin

Full White Pattern

COLORANALYZERTYPE: CA-210

RS-232C Communication

CA-210

7/23/2019 42CS669C

12/41

4.2. EYE-Q function checkStep 1) Turn on the TV set.Step 2) Press EYE key on Adjustment remote control.Step 3) Cover the Eye Q sensor at the front of set for 6 seconds.

Step 4) Check the value of Sensor Data. It must be below 10.If not so, the Eye Q sensor may have some defect.Change the Eye Q sensor.

Step 5) Wait for 6 seconds after withdrawing form the Eye Qsensor.

Step 6) Check the value of Backlight. It must rise.If not so, the Eye Q sensor may have some defect.Change the Eye Q sensor.

* EYE-Q Test is except for LV23xx/LK33x/LK43x series.

4.3. Outgoing condition Configuration- When pressing IN-STOP key by Service remote control, Red

LED are blinked alternatively. And then automatically turnoff. (Must not AC power OFF during blinking)

5. GND and HI-POT Test5.1. GND & HI-POT auto-check preparation

Check the Power cable and Signal cable insertion condition

5.2. GND & HI-POT auto-check(1) Pallet moves in the station. (Power cord / AV cord is tightly

inserted)(2) Connect the AV JACK Tester.(3) Controller (GWS103-4) on.(4) GND Test (Auto)

- If Test is failed, Buzzer operates.- If Test is passed, execute next process (Hi-pot test).(Remove A/V CORD from A/V JACK BOX.)

(5) HI-POT test (Auto)- If Test is failed, Buzzer operates.- If Test is passed, GOOD Lamp on and move to next

process automatically.

5.3. Checkpoint

(1) Test voltage- GND: 1.5 KV / min at 100 mA- SIGNAL: 3 KV / min at 100 mA

(2) TEST time: 1 second(3) TEST POINT

- GND Test = Power cord GND and Signal cord GND.- Hi-pot Test = Power cord GND and LIVE & NEUTRAL.

(4) LEAKAGE CURRENT: At 0.5 mArms

6. Model name & Serial number D/L Press Power on key of service remote control.

(Baud rate : 115200 bps) Connect RS232 Signal Cable to RS-232 Jack. Write Serial number by use RS-232. Must check the serial number at the Diagnostics of SET UP

menu(Refer to below.)

6.1. Signal TABLE

CMD : A0hLENGTH : 85~94h (1~16 bytes)ADH : EEPROM Sub Address high (00~1F)ADL : EEPROM Sub Address low (00~FF)

Data : Write dataCS : CMD + LENGTH + ADH + ADL + Data_1 ++ Data_nDelay : 20ms

6.2. Command Set

* DescriptionFOS Default write : writeVtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,PhaseData write: Model name and Serial number write in EEPROM,.

6.3. Method & noticeA. Serial number D/L is using of scan equipment.B. Setting of scan equipment operated by Manufacturing

Technology Group.C. Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatoryby D-book 4.0.



- 12 -

CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY

No. Adjust mode CMD(hex) LENGTH(hex) Description

1 EEPROM WRITE A0h 84h+n n-bytes Write(n=1~16)

7/23/2019 42CS669C

13/41

* Manual Download (Model Name and Serial Number)If the TV set is downloaded by OTA or Service man, sometimes

model name or serial number is initialized.(Not always)

There is impossible to download by bar code scan, so It needManual download.1) Press the Instart key of Adjustment remote control.2) Go to the menu 6.Model Number D/L like below photo.3) Input the Factory model name(ex 32LV3400-ZG) or Serial

number like photo.

4) Check the model name Instart menu. -> Factory namedisplayed. (ex 32LV3400-ZG)

5) Check the Diagnostics. (DTV country only) -> Buyer modeldisplayed. (ex 32LV3400)

7. CI+ Key Download method(1) Download Procedure

1) Press Power on key of a service remote control.(Baud rate : 115200 bps)

2) Connect RS232-C Signal Cable.3) Write CI+ Key through RS-232-C.4) Check whether the key was downloaded or not at In

Start menu. (Refer to below.)

=> Check the Download to CI+ Key value in LGset.(1) Check the method of CI+ Key value.

a. Check the method on Instart menu.

b. Check the method of RS232C Command.1) Into the main assembly mode (RS232 : aa 00 00)

2) Check the key download for transmitted command.(RS232 : ci 00 10)

3) Result value- normally status for download : OKx- abnormally status for download : NGx

(2) Check the method of CI+ Key value.(RS232)1) Into the main assy mode (RS232 : aa 00 00)

2) Check the method of CI+ key by command(RS232 : ci 00 20)

3) Result valuei 01 OK 1d1852d21c1ed5dcx



CMD 1 CMD 2 Data 0

A A 0 0

CMD 1 CMD 2 Data 0

C I 1 0

CMD 1 CMD 2 Data 0A A 0 0

CMD 1 CMD 2 Data 0

C I 2 0

CI+ key Value

7/23/2019 42CS669C

14/41



- 14 -

1. Power-up boot check

TROUBLESHOOTING

Check stand-by Voltage.

P403 9~12pin : +3.5V_STCheck Power connector.

Main B/D 3.5V Line

Short Check

Check X201 clock.

24 MHzReplace X201.

Check P403 PWR_ON.

1pin : 3.3VReplace Mstar(IC101) or Main board.

Check Multi Voltage.

P403 2pin:24V, 17pin:12VReplace Power Board.

Check Inverter Control & Error Out.

P403 18 pin : High

P403 24 pin : low

Check Power Board or Module.

Check IC402/3/7 Output Voltage.

IC402 : 2.5V

IC403 : 1.1V

IC407 : 1.5V

Q403 : 3.3V

Replace IC402/3/7, Q403.

Re-download software.

Check Micom Voltage.

L404 : +3.5VReplace L404.

Check LVDS Power Voltage.

Q409 : 12VReplace Q409.

Check Mstar LVDS Output Replace Mstar(IC101) or Main Board.

Change Module.

ok

ok

ok

ok

ok

ok

ok

ok

oko

o

o

o

o

o

o

o

o

o

ok

Replace Power board.ok

7/23/2019 42CS669C

15/41



- 15 -

2. Digital TV Video

Check RF Cable & Signal

Check Tuner 3.3V PowerL3703

Replace L3703.

Check Tuner 1.8V Power

IC3703 2 pin : 1.8V

Check IF_P/N Signal

TU3700 10/11 Pin

Replace IC3703.

Check Mstar LVDS Output. Replace Mstar(IC101) o r Main Board.

ok

ok

ok

ok

o

o

o

o

Bad Tuner. Replace Tuner.

3. Analog TV Video

Check RF Cable & Signal.

Check Tuner 3.3V Power.

L3703Replace L3703.


IC3703 2 pin : 1.8V

Check CVBS Signal.

TU3700 8 Pin

Replace IC3703.

Check Mstar LVDS Output. Replace Mstar(IC101) or Main Board.

ok

ok

ok

ok

o

o

o

o


7/23/2019 42CS669C

16/41



- 16 -

4. AV Video

Check input signal format.

Is it supported?

Check AV Cable for damage

for damage or open conductor.

Check JK1604

CVBS Signal Line

R246.

ok

ok

ok

o

Replace Jack.

ok

Check CVBS_DET Signal. Replace R1666.

o

Check Mstar LVDS Output. Replace Mstar(IC101) or Main Board.o

5. Component Video


Is it supported?

Check Component Cablefor damage or open conductor.

Check JK1601 or 1603

Y/PB/PR signal Line.

ok

ok

ok

o

Replace Jack.

Check COMP_DET Signal. Replace R1615.o


ok

o

7/23/2019 42CS669C

17/41



6. SCART Video


Is it supported?

Check Component Cable


Check JK1602

R/G/B and sync signal Line.

o

o

o

o

Replace Jack.

Check SC1_DET Signal. Replace R1614.

o

Check Mstar LVDS Output. Replace Mstar(IC101) or Main Board .

o

o

7. RGB Video


Is it supported?

Check RGB Cable conductorsfor damage or open conductor.

Check EDID

I2C Signal

R138, R139(SDA,SCL).

Check JK1104H/V_Sync/R/G/B Signal Line.

ok

ok

ok

o

o

Re-download EDID data ,Replace Mstar(IC101) or Main Board.

ok

Replace Jack.

Check DSUB_DET. Replace R1146 or R1147.

o

Check Mstar LVDS Output. Replace Mstar(IC101) or Main board.

ok

o

7/23/2019 42CS669C

18/41



8. HDMI Video


Is it supported?

Check HDMI Cable conductors


Check EDID

R4033,R4034,R4035,R4036,

R4037,R4038 I2C Signal.

Check JK801, JK802, JK803.

ok

ok

ok

o

o

Replace the defective IC or re-download EDID data.

Check HDCP EEPROM(IC103)

Power & I2C SignalReplace the defective IC.

ok

o

Replace Jack.

Check HDMI Signal. Check other set.

If no problem, check signal line.

ok

o


ok

o

Replace Main Board.

o

Check HDMI_DET(HPD).o

ok

Replace R830,R828,R862.

7/23/2019 42CS669C

19/41



9. All Source Audio

Check the TV Speaker Menu.

(Menu -> Sound -> TV Speaker)

n

ok

ok

Check Output Signal P501

1, 2, 3, 4 pin.Replace Audio AMP IC(IC501).

ok

o

Check Connector & P501.Replace connector.

if found to be damaged.

ok

o

Check speaker resistance

and connector damage.Replace speaker.

ok

o

ff

Toggle the Menu.

Check AMP IC(IC501) Power

24V or 20V or 15V, 3.3V

o

Replace Amp IC(IC501).

Check Mstar I2S Output

IC501 9,10,11 Pin.

o

Check signal line. Or replace Mstar(IC101).

Check Mstar AUDIO_MASTER_CLK

R148.

o

Replace Mstar(IC101) o r Main Board.

ok

Check AMP I2C Line

R140, R141.

o

Check signal line. Or replace Mstar(IC101).

7/23/2019 42CS669C

20/41



10. Digital TV Audio


Follow procedure

9. All source audio

trouble shooting guide.

ok


L3703.Replace L3703.


IC3703 2 pin : 1.8V

Check IF_P/N Signal

TU3700 10/11 Pin.

Replace IC3703.

ok

ok

ok

o

o

o


11. Analog TV Audio


Follow procedure

9. All source audio


ok


L3703.Replace L3703.


IC3703 2 pin : 1.8V.

Check CVBS SignalTU3700 8 Pin.

Replace IC3703.

ok

ok

ok

o

o

o

Bad Tubner. Replace Tuner.

7/23/2019 42CS669C

21/41



12. AV Audio

Check AV Cable for damage


Check JK1604 & Signal Line.

ok

ok

o

Replace Jack.

Follow procedure

9. All source audio


13. Component/ SCART Audio

Check Component Cable


Check JK1602, JK1603

& Signal Line.

ok

ok

o

Replace Jack.

Follow procedure

9. All source audiotrouble shooting guide.

14. RGB Audio

Check Cable conductors


Check JK1102 & Signal Line.

ok

o

ok

Replace Jack.

Follow procedure

9. All source audio


7/23/2019 42CS669C

22/41



- 22 -

BLOCK DIAGRAM

RGBPC

SPDIF

Component1

H

/POUT

HDMI1/2(DVI)

SI2176

SI2176

(LGIT)

(LGIT)

PC/DVIAudiIn

RS-232C

IF+/-

TU_

CVBS

SIF

L/R

S7LR

IC101

MAX3232

MAX3232

SERIALFLASH

IC1401(8Mbit)

MX25

L8005M2I

SERIALFLASH

IC1401(8Mbit)

MX25

L8005M2I

LVDS

(FHD/50

Hz)

Audio

AMP

NTP7400

USB2.0

DP/DM

SPKL/R

X-tal

24M

FPC(5

1P)

I2S

SPDIF H

/PL/R

CVBS,Y/Pb/Pr,L/R

RGB/H/V

RS232C

Rear

TMDS

DDR3Add.

DDR3Data

SPI

AV2

Side

NAND

FLASH

IC10

2(1Gbit)

PCM_

A[

0:7]

TMDS

HDMI3

CVBS,L/R

DD

R31Gb

IC1202

H5TQ

1G63BFR

DDR

31Gb

IC

1201

H5TQ1G63BFR

C

ONTROL

IR&LED/

SO

FTTOUCH

(TA

CTSWITCH)

SENSOR

_SCL/SDA

LED_

R

KEY1

KEY2

IRLED_

B

SOFTTOUCH

_SCL/SDA

M24M01-HRMN6TP

IC104256Kbit

I2C

AV2

CVBS,L/R

Option

F-SC

ART

SC1_

CVBS_

IN

SC1_

R/G/B

FE_

VOUT

CI Slot

74LCX244

Buffer

TS_

DATA[0:7]

PCM_

DATA

[0:7]

FE_

TS_

DATA[0:7]

PCM_

A[8:14]

7/23/2019 42CS669C

23/41

- 23 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All right reserved.


900

300

200

800

400

540

52

1

530

810

910

120

511

510

LV1

A2

A4

A10

*Set+

Stand

*Stand

Base

+

Body

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These

parts are identified by in the Schematic Diagram and EXPLODED VIEW.

It is essential that these special safety parts should be replaced with the same components as

recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.

Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

7/23/2019 42CS669C

24/41

7/23/2019 42CS669C

25/41

7/23/2019 42CS669C

26/41

7/23/2019 42CS669C

27/41

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Q2406

2SC3052

OPT E

B

C

C24041000pF50V

+3.5V_ST

D903

5.6VCDS3C05HDMI1

NEW_SUB

R 24 13 1 .5 KLED_B/LG_LOGO

R2402100

JP2407

+3.5V_ST

S/T_SDA

S/T_SCL

LED_R/BUZZ

C24030.1uF

16V

C907

18pF

50VOPT

JP2408+3.5V_ST

D24025.6V

AMOTECH

R2429

47K

OPT

D902

5.6VCDS3C05HDMI1

NEW_SUB

R2405

10K

1%

C2408

18pF

50VOPT

C2407100pF50V

SENSOR_SCL

C24020.1uF

+3.5V_ST

C24010.1uF

R2425

47K

OPT

R2431

47K

OPT

R2414

1.5K

R2412

100

EYEQ/TOUCH_KEY

SENSOR_SDA

+3.3V_Normal

C2409

18pF

50VOPT

R24270

+3.5V_ST

C24050.1uF

16V

R242822

R2404

10K1%

KEY1

R2426

47K

IR

C24100.1uF

16V

OPT

KEY2

R2401100

R2411100

EYEQ/TOUCH_KEY

R2416

10K

OPT

L2404

BLM18PG121SN1D

C24061000pF

50V

Q2405

2SC3052

OPT

E

B

C

R243010K

OPT

C906

18pF

50VOPT

D24015.6V

AMOTECH

D24055.6V

D2403

5.6V

EYEQ/TOUCH_K

D24045.6V

EYEQ/TOUCH_K

L2401

BLM18PG121SN1D

L2402BLM18PG121SN1D

L2403

BLM18PG121SN1D

IR & LED

CONTROL

pyright 2012 LG Electronics. Inc. All rights reserved.

y for training and service purposes

7/23/2019 42CS669C

28/41

USBD

OWN

STREAM

USBD

OWN

STREAM






USB1_CTL

R145410K

L1451

MLB-201209-0120P-N2

120-ohm

IC1450

AP2191DSG

EAN61849601

3IN_2

2IN_1

4EN

1GND

5FLG

6OUT_1

7OUT_2

8NC

L1451-*1

CIS21J121

JK1450

3AU04S-305-ZC-(LG)USB_JACK

1

2

3

4

5

+5V_USB

C1452

10uF

10V

USB1_OCD

SIDE_USB_DM

C1453

0.1uFR14582K1/8W1%

R14592K1/8W1%

JK1450-*1

3

AU04S-345-ZC-H-LG

USB_JACK_LV3400

1

2

3

4

5

R1455

4.7K

OPT

D1451

RCLAMP0502BA

OPT

SIDE_USB_DP

+3.3V_Normal

C1451

22uF

16V

R1451 47

USB_DIODES

$0.077



7/23/2019 42CS669C

29/41






5V_DET_HDMI_4

DDC_SDA_1

R862

10K

D1+_HDMI2

HDMI_CEC

D0-_HDMI1

JK801

EAG59023302

HDMI_

2

14

13

5D1_GND

20

SHIELD

12

11

2D2_GND

19

18

10CK+

4D1+

1D2+

17

9D0-

8D0_GND

3D2-

16

7D0+

6D1-

15

JP805

Q801

2SC3052

E

B

C

CK-_HDMI4

D0+_HDMI2

R 81 5 0

IC

R1EX24

HDMI_

3A2

2A1

4VSS

1A0

D2-_HDMI2

HPD4R82810K

CK+_HDMI1

D0+_HDMI4

R896

1K

R805 0

OPT

Q803

2SC3052

E

B

C

R803

1.8K

HPD2

D811

OPT

D801

OPT

5V_DET_HDMI_2

D802

OPT

HDMI_CEC

R837

1.8K

DDC_SCL_4

HDMI_CEC

DDC_SDA_2

JK803

EAG62611201

HDMI_SIDE

14

13

5D1_GND

20

BODY_SHIELD

12

11

2D2_GND

19

18

10CK+

4D1+

1D2+

17

9D0-

8D0_GND

3D2-

16

7D0+

6D1-

15

D0+_HDMI1

R808

10K

R804

1.8K

IC80

R1EX240

HDMI_

3A2

2A1

4VSS

1A0

D2+_HDMI4

CK-_HDMI2

R806

10K

D1-_HDMI2

DDC_SCL_1

CK+_HDMI4

JP806

JK802

EAG59

023302

HDMI_

1

14

13

5D1_GND

20

SHIELD

12

11

2D2_GND

19

18

10CK+

4D1+

1D2+

17

9D0-

8D0_GND

3D2-

16

7D0+

6D1-

15

CK+_HDMI2

5V_DET_HDMI_1

IC8

R1EX24

HDMI_

3A2

2A1

4VSS

1A0

R830

10K

D0-_HDMI2

CK-_HDMI1

C802

0.1uF

16V

D1-_HDMI1

DDC_SDA_4

R841 0

R897

1K

R807

10K

R895

1K

Q802

2SC3052

E

B

C

D1+_HDMI4

R835

3.3K

DDC_SCL_2

C803

0.1uF

16V

5V_HDMI_4

HDMI_ARC

D2-_HDMI4

D2+_HDMI2

5V_HDMI_2

D0-_HDMI4

D1-_HDMI4

D2+_HDMI1

D2-_HDMI1

R802

3.3K

R801

3.3K

HPD1

C801

0.1uF

16V

5V_HDMI_1

D1+_HDMI1

R824 0

HDMI_1

HDMI_2SIDE_HDMI



7/23/2019 42CS669C

30/41

7/23/2019 42CS669C

31/41






C1106

0.1uF

PM_RXD

C11030.1uF

C1101 0.33uF

C11040.1uF

+3.5V_ST

D1107

30VCDS3C30GTH

OPT

R1123100

C11050.1uF

C11020.1uF

R1124100

IC1101

MAX3232CDR

EAN41348201

3C1-

2V+

4C2+

1C1+

6V-

5

C2-

7DOUT2

8RIN2

9ROUT2

10DIN2

11DIN1

12

ROUT1

13RIN1

14DOUT1

15GND

16VCC

PM_TXD

D1108

30VCDS3C30GTH

OPT

RS232C



7/23/2019 42CS669C

32/41






RXA2+

RXA1-

R710

10K

OPT

RXB1+

RXA2-

RXB3+

C700

10uF

16VOPT

RXACK+

RXBCK+

L702120-ohmWAFER_FHD

RXACK-

RXB0+

RXBCK-

RXA0-

RXA4+

RXA4-

C709

1000pF

50VOPT

RXB0-

R705

3.3K

OPT

+3.3V_Normal

P703

FI-RE51S-HF-J-R1500

WAFER_FHD

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

RXB1-

C710

0.1uF

16VWAFER_FHD

P705

FF10001-

HD

2

2

2

2

2

2

2

2

2

2

31

RXB2-

RXB4+

RXA0+

RXA3-

RXA3+

RXA1+

PANEL_VCC

R70910K

BIT_SEL_LOW

RXB3-

RXB4-

RXB2+

LVDS_SEL

[51Pin LVDS Connector](For FHD 60/120Hz)

BIT_SEL

[30Pin LV

(For HD



7/23/2019 42CS669C

33/41

7/23/2019 42CS669C

34/41






SPI_SCK

+3.5V_ST

Q1401

KRC103S

OPTE

B

C

+3.5V_ST

C1401

0.1uF

R1404

4.7K

OPT

/SPI_CS

SPI_SDO

IC1401

MX25L8006EM2I-12G

S_FLASH_MAIN_MACRONIX

3WP#

2SO/SIO1

4GND

1CS#

5SI/SIO0

6SCLK

7HOLD#

8VCC

R140533

R1403

10K

OPT

SPI_SDI

/FLASH_WP

R1401

0OPT

IC1401-*1

W25Q80BVSSIG

S_FLASH_MAIN_WINBOND

3%WP[IO2]

2DO[IO1]

4GND

1CS

5DI[IO0]

6CLK

7HOLD[IO3]

8VCC

+3.5V_ST



7/23/2019 42CS669C

35/41

7/23/2019 42CS669C

36/41

THERMAL






0.1uFC501

50V

0.1uF

C521

50V

C528

1uF

25V

+24V_AMP

0.1uF

C519

50V

+24V_AMP

0.1uF

C514

16V

C533390pF50V

0.1uFC513

16V

C5161000pF

50V

AMP_SCL

R 50 3 1 00

R51512

+24V_AMP

R51412

R501

10K

L5

10

R50210K

D504

100V

1N4148W

OPT

R51212

C526

22000pF

50V

0.1uF

C522

50V

AUD_MASTER_CLK

AMP_RESET

C530390pF50V

L502

BLM18PG121SN1D

R50912

C507

33pF

50V

C523

10uF

35V

IC501

NTP-7400L

1AGND_PLL

2AVDD_PLL

3DVDD_PLL

4LF

5DGND_PLL

6GND_1

7DGND

8DVDD

9SDATA

10WCK

11BCK

12SDA

13

SCL

14

/FAULT

15

MONITOR

0

16

MONITOR

1

17

MONITOR

2

18

BST

2B

19

PGND

2B

20

OUT

2B_

1

21

OUT

2B_

2

22

PVDD

2_

1

23

PVDD

2_

2

24

PVDD

2_

3

25 OUT2A_1

26 OUT2A_2

27 PGND2A

28 BST2A

29 VDR2

30 GND_2

31 VCC_5

32 VDR1

33 BST1B

34 PGND1B

35 OUT1B_1

36 OUT1B_237

PVDD

1_

1

38

PVDD

1_

2

39

PVDD

1_

3

40

OUT

1A_

1

41

OUT

1A_

2

42

PGND

1A

43

BST

1A

44

/RESET

45

AD

46

GND_

IO

47

CLK_

I

48

VDD_

IO

49

[EP]

0.1uF

C520

50V

Q501

2SC3052

E

B

C

R505

3.3K

L5

10

D502

100V

1N4148W

OPT

R50812

D503

100V

1N4148W

OPT

L504

10.0

R51112

R506

100

C529

1uF

25V

0.1uFC502

50V

C517

22000pF

50V

+24VC525

0.01uF

50V

OPT

C518

22000pF

50V

C5120.1uF

16V

AUD_LRCK

C51110uF10V

OPT

C534

1uF

25V

C531390pF50V

L503

10.0

C505

1000pF

50V

L501

MLB-201209-0120P-N2

C524

10uF

35V

C527

22000pF

50V

+3.5V_STC509

33pF

50V

AMP_MUTE

C503

100pF

50V

D501

100V

1N4148W

OPT

AMP_SDA

0.1uFC508

16V

C515

10uF

10V

C50610uF10V

OPT

+3.3V_Normal

C532390pF50V

AUD_LRCH

R51312

AUD_SCK

R5073.3

OPT

C5041000pF50V

C51010uF10V

OPT

R 50 4 1 00

R51012

R52010K

R52110K



7/23/2019 42CS669C

37/41

7/23/2019 42CS669C

38/41






R99151K

SIDE_CVBS

L9902BLM18PG121SN1D

SIDE_CVBS

L9901BLM18PG121SN1D

SIDE_CVBS

R990975

SIDE_COMP

S

R9913

10K

SIDE_CVBS

D990630V

SIDE_COMP

R990410K

SIDE_COMP

D990730V

SIDE_COMP

R990775

SIDE_CVBS

R99121K

SIDE_COMP

S

JK9901

KJA-PH-1-0177

SIDE_AV_GENDER

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

COMP2_Y+

C9907

100pF

OPT

D990530V

SIDE_COMP

R991712K

SIDE_CVBS

COMP2_DET

JK9902

KJA-PH-1-0177

SIDE_COMP

3 M3_DETECT

4 M4

5 M5_GND

1 M1

6 M6

D99025.6V

OPT

ADMC5M03200L_AMODIODE

S

D99035.6V

SIDE_CVBS


R9906

470K

SIDE_CVBS

D99045.6V

SIDE_CVBS


L9903

BLM18PG121SN1D

SIDE_CVBS

C9905

100pF

50V

SIDE_CVBSR9916

12K

SIDE_CVBS

COMP2_Pr+

R9911

10KSIDE_CVBS

D99085.6V

OPT

+3.3V_Normal

COMP2_Pb+

+3.3V_Normal

C9901

100pFSIDE_CVBS

D9901

30V

SIDE_CVBS

ADUC30S03010L_AMODIODE

C9906

100pF50V

SIDE_CVBS

R9914

10K

SIDE_CVBS

S

R990875

SIDE_COMP

R991075

SIDE_COMP

R9905470K

SIDE_CVBS

JK9903

PPJ235-01

SIDE_AV_3HOLE

4A[YL]O-SPRING

5A [YL]E-LUG

3A [YL]CONTACT

4B [WH]O-SPRING

3C [RD]CONTACT

4C [RD]O-SPRING

5C[RD]E-LUG

(New Item Developmen)

SIDE CVBS PHONE JACK

SIDE COMPONENT PHONE JACK

(New Item Development)



7/23/2019 42CS669C

39/41

7/23/2019 42CS669C

40/41






MDL61930001

GAS5

DO_NOT_APPLY

MDL61930001

GAS3

DO_NOT_APPLY

MDL61930001

GAS6

DO_NOT_APPLY

MDL61930001

GAS2

DO_NOT_APPLY

MDL61930001

GAS1

DO_NOT_APPLY

MDL61930001

GAS7

DO_NOT_APPLY

MDL61930001

GAS4

DO_NOT_APPLY

MDS62110205

GAS3-*2

7.5T_GAS

MDS62110209

GAS7-*5

8.5T_GAS

MDS62110204

GAS1-*1

5.5T_GAS

MDS61887708

GAS4-*4

12.5T_GAS

MDS62110204

GAS3-*1

5.5T_GAS

MDS61887708

GAS5-*4

12.5T_GAS

MDS61887708

GAS7-*4

12.5T_GAS

MDS62110204

GAS4-*1

5.5T_GAS

MDS62110205

GAS5-*2

7.5T_GAS

MDS62110205

GAS4-*2

7.5T_GAS

MDS62110209

GAS1-*5

8.5T_GAS

MDS62110205

GAS2-*2

7.5T_GAS

MDS62110209

GAS3-*5

8.5T_GAS

MDS62110209

GAS5-*5

8.5T_GAS

MDS62110209

GAS6-*5

8.5T_GAS

MDS62110205

GAS1-*2

7.5T_GAS

MDS61887708

GAS6-*4

12.5T_GAS

MDS62110204

GAS6-*1

5.5T_GAS

MDS61887708

GAS2-*4

12.5T_GAS

MDS61887708

GAS1-*4

12.5T_GAS

MDS62110204

GAS2-*1

5.5T_GAS

MDS62110205

GAS6-*2

7.5T_GAS

MDS62110205

GAS7-*2

7.5T_GAS

MDS62110204

GAS5-*1

5.5T_GAS

MDS62110204

GAS7-*1

5.5T_GAS

MDS62110209

GAS2-*5

8.5T_GAS

MDS62110209

GAS4-*5

8.5T_GAS

MDS61887708

GAS3-*4

12.5T_GAS

MDS62110206

GAS7-*6

6.5T_GAS

MDS62110206

GAS3-*6

6.5T_GAS

MDS62110206

GAS2-*6

6.5T_GAS

MDS62110206

GAS4-*6

6.5T_GAS

MDS62110206

GAS5-*6

6.5T_GAS

MDS62110206

GAS6-*6

6.5T_GAS

MDS62110206

GAS1-*6

6.5T_GAS

MDS62110214

GAS6-*3

9.5T_

GAS

MDS62110214

GAS1-*3

9.5T_GAS

MDS62110214

GAS4-*3

9.5T_

GAS

MDS62110214

GAS2-*3

9.5T_G

AS

MDS62110214

GAS7-*3

9.5T_

GAS

MDS62110214

GAS3-*3

9.5T_G

AS

MDS62110214

GAS5-*3

9.5T_

GAS

SMD GASKET



7/23/2019 42CS669C

41/41