1
17th Symposium of AER
on VVER Reactor Physics and Reactor Safety
September 24-29, 2007, Yalta, Crimea, Ukraine
FUEL PERFORMANCE AND FUEL PERFORMANCE AND OPERATION EXPERIENCE OF OPERATION EXPERIENCE OF
VVER-440 FUEL IN VVER-440 FUEL IN IMPROVED FUEL CYCLEIMPROVED FUEL CYCLE
A. Gagarinski, V. ProselkovA. Gagarinski, V. Proselkov, Yu. Semchenkov, Yu. Semchenkov
Russian Research Center “Kurchatov Institute”
Moscow, Russia
2
Since September 2002, Kola NPP performs works introducing second-generation fuel in VVER-440 reactors. Currently this second-generation fuel is in trial operation at unit 3 (fuel cycles No 18-21, 2002-2007) and unit 4 (fuel cycles No 18-19, 2005-2007).
The first 2nd-generation fuel for VVER-440 was loaded in Kola-3 reactor during its 18th fuel loadinge (September 2002-July 2003)
3
The fresh fuel of this 18th fuel loading included the following new second-generation assemblies:
- 54 fuel assemblies with average U-235 enrichment of 4.25%, and with Gd2O3 burnable absorber (6 gadolinium fuel elements) integrated into the fuel;
- 6 CR fuel followers with average fuel part enrichment of 3.82% of U-235.
The fresh fuel of the next, 19th fuel loading (performed during the scheduled preventive maintenance (SPM) in 2003) also consisted of second-generation assemblies only:
- 54 fuel assemblies with average U-235 enrichment of 4.25%, and with Gd2O3 burnable absorber (6 gadolinium fuel elements) integrated into the fuel;
- 12 CR fuel followers with average fuel part enrichment of 3.82% of U-235.
The 20th fuel loading (SPM-2004) consisted of 60 working assemblies and 6 second-generation assemblies.
The 21st fuel loading (SPM-2006) consisted of 54 working assemblies and 12 second-generation assemblies.
4
Since April 2005, an improved fuel cycle similar to that of unit 3 using the 2nd-generation fuel for VVER-440 reactors is being introduced at unit 4 Kola NNP.
5
VVER-440 fuel assembly parameters increased pitch between fuel elements in fuel clusters (from 12.2 to 12.3 mm for fuel assemblies and for CR fuel followers);
increased fuel column length in fuel rods (from 2424 to 2480 mm for FA);
reduced central hole diameter in fuel pellets (from 1.6 to 1.35 mm);
increased external diameter of fuel pellets (from 7.57 to 7.60 mm);
reduced external diameter of fuel elements (from 9.1 to 9.07 mm);
Gd2O3 burnable absorber (3.35%) integrated into the fuel;
use of hafnium plates in CR fuel followers coupler part;
turnkey housing size for FA and CR-FF types (145 mm);
fuel element coating made of zirconium-niobium (1%) alloy with reduced hafnium content (to 0.01%);
stronger fixation of fuel elements into assemblies .
6
Power density limits for second-generation assemblies with 4.25% enrichment
qlMAX= 325 W/cm
qladd in accordance with the admissible local linear heat
rate curve depending on the burnup fuel rod.
0 10 20 30 40 50 60 70
Ñ ðåä í åå âû ãî ðàí èå â òâýë å, Ì Â ò ñóò/êãUA verage B urnup in Fuel R od, MWd/kgU
0
50
100
150
200
250
300
350
Ëè
íå
éí
àÿ
òå
ïë
îâ
àÿ
ìî
ùí
îñ
òü, Â
ò/ñ
ìL
ine
ar
He
at
Ra
te, W
t/c
m
(15,325)
(0,325)
(35,285)
(70,200)(60,215)
7
Trial operation data for second-generation fuel assemblies
After two fuel loading maximum average assembly burnup was achieved in second-generation assemblies
of unit 4 (by the end`19th fuel loading):24.13 MWday/kgU for fuel assemblies.
After three fuel loading maximum average assembly burnup was achieved in second-generation assemblies
of unit 3 (by the end of its 20th fuel loading):
35.7 MWday/kgU for fuel assemblies
8
0
5
10
15
20
25
30
35
10-1
1
11-1
2
12-1
3
13-1
4
14-1
5
15-1
6
16-1
7
17-1
8
18-1
9
19-2
0
20-2
1
21-2
2
22-2
3
23-2
4
24-2
5
25-2
6
26-2
7
27-2
8
28-2
9
29-3
0
30-3
1
31-3
2
32-3
3
33-3
4
34-3
5
35-3
6
Интервалы выгораний, МВт*сут/кг
Кол
ичес
тво
ТВ
С
Number of assemblies
Burnup ranges, MWday/kg
Burnup distribution in second-generation working assemblies based on the results of 3 years of 2nd-generation assemblies’ operation at unit 3
9
Calculated and experimental concentrations of the liquid absorber (boric acid) are
compared during fuel operation cycles It can be seen that the calculated values of critical boric acid concentrations correspond to the
results of measurements.
10
Critical boric acid concentration changing in the process of burnup fuel loading,
measurementscalculations
CH3BO3, g/kg H2O
18th fuel loading of Kola NPP unit 3
11
Critical boric acid concentration changing in the process of burnup fuel loading,
19th fuel loading of Kola NPP unit 3 measurementscalculations
CH3BO3, g/kg H2O
12
Critical boric acid concentration changing in the process of burnup fuel loading,
20th fuel loading of Kola NPP unit 3
13
Critical boric acid concentration changing in the process of burnup fuel loading,
19th fuel loading of Kola NPP unit 4 (2007 year)
14
Specific conditions of Kola NPP operation in an isolated energy system resulting in an insufficient demand for its electricity compels one of its units
to operate at only 50% of its design capacity
20th fuel loading of Kola NPP unit 3
15
19th fuel loading of Kola NPP unit 4 (2007 year)
16
The results of comparison of Kq (relative assembly power) measured by thermocouples and calculated for selected moments of unit 3, 20th fuel loading.
Deviation statistics
(Experiment-Calculation)/Calculation,
in % for assemblies having different operation periods
red - 1 cycle;yellow - 2 cycles;green - 3 cycles;turquoise- 4 cycles;blue - 5 cycles;violet - 6 cycles.
Measuring date:18.03.2005Effective days: 150.6Power: 1354 MW.
17
The results of comparison of Kq (relative assembly power) measured by thermocouples and calculated for selected moments of unit 4, 19th fuel loading.
Deviation statistics
(Experiment-Calculation)/Calculation,
in % for assemblies having different operation periods
red - 1 cycle;yellow - 2 cycles;green - 3 cycles;turquoise- 4 cycles;blue - 5 cycles;violet - 6 cycles.
Measuring date:04.10.2006Effective days: 107.8Power: 1354 MW.
18
Primary circuit water chemistry data The primary circuit of Kola-3 operated in a reducing, faintly alkaline, ammonium-potassium water chemistry mode using boric acid, in accordance with existing requirements. In order to meet the water chemistry standards by ammonium and hydrogen, hydrazine hydrate was supplied to the intake header of makeup pumps. In steady-state operation conditions, the contents of alkaline metals, chlorides and corrosion products, pH, and hydrogen concentration in the primary coolant were within the standard limits throughout the reported year.
19
Primary coolant activity and special water treatment-1
coolant flow data
Specific activity of the primary coolant determined for the sum of iodines during the operation of the 18th and 19th load patterns of unit 3 stayed at a low level of 310-5 Ci/kg. The growth of coolant activity up to 310-5 Ci/kg at the initial
stage (15.09.02-24.12.02) of the 18th fuel loading operation at unit 3 was caused by its power increase to 100%. In course of
further operation, the coolant activity stayed practically unchanged.
The absence of coolant activity excursion in the moment of actuation of emergency protection system-1 (18th fuel load
pattern) shows that no fuel elements having significant cladding defects are present in the core.
20
0,00E+00
1,00E-05
2,00E-05
3,00E-05
4,00E-05
5,00E-05
6,00E-05
Date
Activity, C
i/kg
NGFP total Сум.йод
Specific activity of iodines and non-gaseous fission products in the primary coolant; 18th fuel load pattern, Kola NPP unit 3
0
20
40
60
80
100
120
Date
G, t/h Nt,%
Thermal power (%) and SWT-1 coolant flow rate (t/h);
18th fuel load pattern, Kola NPP unit 3
21
1,E-06
1,E-05
1,E-04
1,E-0312.09.2003
19.09.2003
26.09.2003
03.10.2003
10.10.2003
17.10.2003
24.10.2003
31.10.2003
07.11.2003
14.11.2003
21.11.2003
28.11.2003
05.12.2003
12.12.2003
19.12.2003
26.12.2003
02.01.2004
09.01.2004
16.01.2004
23.01.2004
30.01.2004
06.02.2004
13.02.2004
20.02.2004
27.02.2004
05.03.2004
12.03.2004
19.03.2004
26.03.2004
02.04.2004
09.04.2004
16.04.2004
23.04.2004
30.04.2004
07.05.2004
14.05.2004
21.05.2004
28.05.2004
04.06.2004
11.06.2004
18.06.2004
I total
NGFP total
Specific activity of iodines and non-gaseous fission products in the primary coolant; 19th fuel loading, Kola NPP unit 3 (2 hours after sampling), Ci/kg
0
20
40
60
80
100
120
12
.0
9.2
00
3
19
.0
9.2
00
3
26
.0
9.2
00
3
03
.1
0.2
00
3
10
.1
0.2
00
3
17
.1
0.2
00
3
24
.1
0.2
00
3
31
.1
0.2
00
3
07
.1
1.2
00
3
14
.1
1.2
00
3
21
.1
1.2
00
3
28
.1
1.2
00
3
05
.1
2.2
00
3
12
.1
2.2
00
3
19
.1
2.2
00
3
26
.1
2.2
00
3
02
.0
1.2
00
4
09
.0
1.2
00
4
16
.0
1.2
00
4
23
.0
1.2
00
4
30
.0
1.2
00
4
06
.0
2.2
00
4
13
.0
2.2
00
4
20
.0
2.2
00
4
27
.0
2.2
00
4
05
.0
3.2
00
4
12
.0
3.2
00
4
19
.0
3.2
00
4
26
.0
3.2
00
4
02
.0
4.2
00
4
09
.0
4.2
00
4
16
.0
4.2
00
4
23
.0
4.2
00
4
30
.0
4.2
00
4
07
.0
5.2
00
4
14
.0
5.2
00
4
21
.0
5.2
00
4
28
.0
5.2
00
4
04
.0
6.2
00
4
11
.0
6.2
00
4
18
.0
6.2
00
4
Nt % Q SWT-1 (t/h)
Thermal power (%) and SWT-1 coolant flow rate (t/h); 19th fuel loadind, Kola NPP unit 3
22
ConclusionThe specific geographical position of Kola NPP and the state of the surrounding region’s economy determine the strategy of power units’ operation in the area of fuel use.
Isolated energy system and, as a consequence, excessive generating capacities compel Kola NPP to operate at low power, though its units’ operation at their maximum power may be needed in some unplanned situations.
In the same time, the results of trial industrial operation of second-generation fuel at Kola NPP units 3 and 4 demonstrate a high reliability of new fuel types, which is confirmed by low primary coolant activity levels and by the cladding leakage monitoring data.
23
The process of trial industrial operation of second-generation assemblies includes the comparison of calculated and experimental data performed in order to check the compliance of fuel’s neutronic parameters with the theoretical physical project of fuel cycle implementation, as well as to update the related software and the database of constants.
Starting from the third refueling, the divergences of fuel load operating cycle and of the liquid absorber concentration in power operation mode were discovered, which required the works on identifying the reasons of these divergences and on correcting the constants to be organized. Regulatory documents provide for the updating of neutronic constants on the basis of operating data.
Technical solutions laid in the design of second-generation fuel assemblies, were proven and confirmed by the results of trial and commercial operation.