RoHS Compliant
Rev A.0, 12/02/2010 1
Features
RoHS compliant
10Gb/s optical links
Compliant with XFP MSA
Support multi protocol from 9.9Gb/s to
11.3Gb/s
Transmission distance of 80km over single
mode fiber
DWDM EML laser transmitter
LC duplex connector
2-wire interface for management and
diagnostic monitor
Hot pluggable 30 pin connector
XFI electrical interface with AC coupling
Power supply voltages : +3.3V, +5V
Power dissipation: <3.5W
Three optional operating temperature ranges :
Option ST : 0°C to 70°C
Option ET : -5°C to 85°C
Option IT : -40°C to 85°C
Applications
SONET OC-192 LR-2 / SDH L-64.2a
10GBASE-ZR/ZW Ethernet
80km 10G FC
G.709 OUT-2
Description
OE Solutions’ XFP transceivers are designed to
be compatible with the XFP 30pin Multi-Source
Agreement (MSA). The high performance cooled
1550nm EML transmitter and high sensitivity
APD receiver provide superior performance for
SONET/SDH and Ethernet applications up to
80km optical links.
Advanced Digital Diagnostics functions are
available via the 2-wire serial bus specified in the
XFP MSA. The transmitter and receiver features
ac-coupled differential data inputs and outputs,
and an LVTTL for Tx disable input and Tx fault
output. Software TX disable is also implemented.
The receiver features differential ac-coupled data
outputs and LVTTL for LOS (Loss of Signal)
output.
10Gb/s DWDM XFP 80km Transceiver
RDXX0SZR
Rev A.0, 12/02/2010 2
RDXX0SZR DWDM XFP Transceiver Product Specifications
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Notes
Absolute Supply Voltage Vcc3_max 0 - 3.6 V -
Vcc5_max 0 - 6.0 V -
Operating Case Temperature Top -40 - 85 °C 1,2
Operating Relative Humidity RHop 5 - 90 % 3
Storage and TransportationTemperature Tst -40 - 85 °C 3
Storage and Transportation
Relative Humidity
5 - 95 % 3
Notes: 1. Measured on bottom side front center of XFP modu-le 2. There are three options of operating maximum temperature:
Option ST: standard temperature from 0oC to 70
oC,
Option ET: extended temperature from -5oC to 85
oC, and
Option IT: extended temperature from -40oC to 85
oC
3. Non-condensing
2. General Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Notes
Bit Rate B 9.9 10.3 11.3 Gb/s -
Maximum Transmission Distance Dmax 80 - - km -
Operating Voltage Vcc3 3.13 - 3.47 V -
Vcc5 4.75 - 5.25 V -
Power Supply Current ICC3 - 200 480 mA -
Power Supply Current ICC5 - - 420 mA 1
Total Power Consumption - - 3.5 W -
ESD (High speed pins) - - 500 V 2
Notes : 1. Supplies TEC, Current draw depends on Temperature 2. Human body model per JEDEC JESD22-A114-B, compliant with INF-8077i Rev. 4.5 August 31, 2005
Rev A.0, 12/02/2010 3
RDXX0SZR DWDM XFP Transceiver Product Specifications
3. Electrical Specifications
3.1 Module Electrical Specifications (Over Operating Case Temperature and Power Supply Range)
Parameter Symbol Min. Typ. Max. Unit Notes
XFP Interrupt, Mod_NR Vol 0.0 - 0.4 V -
Voh Vcc3-0.5 - Vcc3+0.3 V 1
P_Down/RST Vil -0.3 - 0.8 V -
Vih 2.0 - Vcc3+0.3 V -
Interrupt Assert Delay Interrupt_on - - 200 ms -
Interrupt Negate Delay Interrupt_off - - 500 µs -
Mod_NR Assert / Negate Delay - - - 1 ms -
P-Down/Reset Assert delay - 100 - - µs 2
P-Down/Reset De-assert delay - 5 - - s 2
Note : 1. Vcc3 is the voltage of host board 2. Power down mode.
3.2 Transmitter Electrical Specifications (Over Operating Case Temperature and Power Supply Range)
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Differential Input Impedance Rin 80 100 120 Ω -
Differential Data Input Swing Vin,pp 120 - 1000 mVp-p -
Tx Disable Voltage Vd 2.0 - Vcc3+0.3 V 1
Tx Enable Voltage Ven 0 - 0.8 V -
Tx Disable Assert Time T_off - - 1 ms -
Tx Enable Assert Time T_on - - 5 s -
Initialization Time T_start - - 60 s -
Note : 1. Vcc3 is the voltage of host board
3.3. Receiver Electrical Specifications (Over Operating Case Temperature and Power Supply Range)
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Data Rate B 9.9 10.3 11.3 GBd -
Differential Output Impedance Rout 80 100 120 Ω -
Differential Data Output Swing Vout 340 - 850 mVp-p -
Data Output Rise/Fall Time tr/tf - - 45 ps -
LOS Output High Voltage Vlosh Vcc3-0.5 - Vcc3+0.3 V 1
LOS Output Low Voltage Vlosl 0 - 0.4 V -
LOS Assert/Deassert Time Delay T_los on/off - - 100/10 µs/ms -
Note : 1. Vcc3 is the voltage of host board
Rev A.0, 12/02/2010 4
RDXX0SZR DWDM XFP Transceiver Product Specifications
4. Optical Specifications
4.1 Transmitter Optical Specifications (Over Operating Case Temperature and Power Supply Range)
Optical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Laser Safety Class Class 1 according to IEC60825 -
Optical Wavelength λ 1529 - 1562 nm -
Average Optical
Output Power
BOL Pout -1 - +3 dBm 1
EOL -2 - +3
Optical Power Overshoot Pov - - 1 dB 2
Optical power of OFF transmitter Pout-off - - -40 dBm -
Spectral Width ∆λ -8 - 8 GHz 3
Optical Output Power Variation
(with respect to BOL Tc=25°C,
and nominal power supply)
∆ Pout -1 - +1 dB -
Side Mode Suppression Ratio SMSR 30 - - dB 4
Wavelength
Deviation
BOL ∆λT -50 - +50 pm 5
EOL ∆λa -100 - +100 pm
Optical Return Loss RL 24 - - dB -
Optical Extinction Ratio (Unfiltered) ER 9.0 - - dB -
Optical Rise/Fall Time (20%-80%) Tr, Tf - - 35 ps -
Output Jitter - - - - 6
Notes: 1. Average power measured at output 2. Defined as Peak power – Steady-state power (in dBm) when Tx-dis is de-asserted or when the module is hot plugged with Tx_dis in low state (Tx enabled). 3. Full spectral width (RBW=0.1nm) measured 15dB down from the maximum of center wavelength peak under full modulation condition 4. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode peak under full modulation condition 5. Deviation related to the ITU standardized wavelength. The EOL value is met as soon as the output average power is above 10% of the steady-state power. 6. The jitter performance meets Telcodia GR-253-Core and ITU-T Recommendations G.783, G813, G825 and G82511 with ITU-T 0.172(04/2005) for the measurement methods and the measurement equipment.
Laser Safety: All transceivers in this datasheet are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions.
Rev A.0, 12/02/2010 5
RDXX0SZR DWDM XFP Transceiver Product Specifications
4. ITU Channel and Wavelength Guide
ITU Channel Frequency
(THz)
Wavelength
(nm) ITU Channel
Frequency
(THz)
Wavelength
(nm)
20 192.0 1561.42 41 194.1 1544.53
21 192.1 1560.61 42 194.2 1543.73
22 192.2 1559.79 43 194.3 1542.94
23 192.3 1558.98 44 194.4 1542.14
24 192.4 1558.17 45 194.5 1541.35
25 192.5 1557.36 46 194.6 1540.56
26 192.6 1556.56 47 194.7 1539.77
27 192.7 1555.75 48 194.8 1538.98
28 192.8 1554.94 49 194.9 1538.19
29 192.9 1554.13 50 195.0 1537.40
30 193.0 1553.33 51 195.1 1536.61
31 193.1 1552.52 52 195.2 1535.82
32 193.2 1551.72 53 195.3 1535.04
33 193.3 1550.92 54 195.4 1534.25
34 193.4 1550.12 55 195.5 1533.47
35 193.5 1549.32 56 195.6 1532.68
36 193.6 1548.51 57 195.7 1531.90
37 193.7 1547.72 58 195.8 1531.12
38 193.8 1546.92 59 195.9 1530.33
39 193.9 1546.12 60 196.0 1529.55
40 194.0 1545.32
Rev A.0, 12/02/2010 6
RDXX0SZR DWDM XFP Transceiver Product Specifications
4.2. Receiver Optical Specifications (Over Operating Case Temperature and Power Supply Range)
Optical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Optical Wavelength λ 1528 1563 nm -
Maximum Input Power Pol -6.0 - - dBm -
Receiver Reflectance - - - -27 dB -
LOS Assert LOS_A -35 - - dBm -
LOS De-assert LOS_D - - -27 dBm -
LOS Hysteresis - - 2 5 dB -
Application with FEC
Parameter/ Test Conditions Dispersion Min. Typ. Max. Unit
Power Sensitivity at λ DWDM
1. No ASE noise (or OSNR 0.1nm > 30dB)
2. Data Rate: up to 11.3176Gb/s
3.BER=1x10-4
0ps/nm - - -27 dBm
1300ps/nm - - -25 dBm
1600ps/nm - - -23 dBm
Application without FEC
Parameter/ Test Conditions Dispersion Min. Typ. Max. Unit
Power Sensitivity at λ DWDM
1. No ASE noise (or OSNR 0.1nm > 30dB)
2. Data Rate: up to 10.3125Gb/s
3.BER=1x10-12
0ps/nm - - -24 dBm
1300ps/nm - - -22 dBm
Rev A.0, 12/02/2010 7
RDXX0SZR DWDM XFP Transceiver Product Specifications
5. Pin Descriptions
XFP Transceiver Electrical Pad Layout
Rev A.0, 12/02/2010 8
RDXX0SZR DWDM XFP Transceiver Product Specifications
Pin Descriptions (continued)
Pin Logic Symbol Description Notes
1 - GND Module Ground 1
2 - VEE5 Not required
3 LVTTL-I Mod_DeSel Module De-select; When held low allows module to respond to 2-wire serial
interface
4 LVTTL-O Interrupt Interrupt; Indicates presence of an important condition which can be read over
the 2-wire serial interface 2
5 LVTTL-I TX_DIS Transmitter Disable; Turns off transmitter laser output
6 - VCC5 +5V Power Supply
7 - GND Module Ground 1
8 - VCC3 +3.3V Power Supply
9 - VCC3 +3.3V Power Supply
10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2
11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2
12 LVTTL-O Mod_Abs Indicates Module is not present. Grounded in the Module 2
13 LVTTL-O Mod_NR Module Not Ready; Indicating Module Operational Fault 2
14 LVTTL-O RX_LOS Receiver Loss Of Signal Indicator 2
15 - GND Module Ground 1
16 - GND Module Ground 1
17 CML-O RD- Receiver Inverted Data Output, AC coupled in the module
18 CML-O RD+ Receiver Non-Inverted Data Output, AC coupled in the module
19 - GND Module Ground 1
20 - VCC2 Not required 3
21 LVTTL-I P_Down/RST
Power down; When high, requires the module to limit power consumption to
1.5W or below. 2-Wire serial interface must be functional in the low power
mode.
Reset; The falling edge initiates a complete reset of the module including the 2-
wire serial interface, equivalent to a power cycle.
22 - VCC2 No use 3
23 - GND Module Ground 1
24 PECL-I RefCLK+ Not required
25 PECL-I RefCLK- Not required
26 - GND Module Ground 1
27 - GND Module Ground 1
28 CML-I TD- Transmitter Inverted Data Input, AC coupled in the module
29 CML-I TD+ Transmitter Non-Inverted Data Input, AC coupled in the module
30 - GND Module Ground 1
Notes : 1. Module ground pins Gnd are isolated from the module case and chassis ground within the module.
2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.
Rev A.0, 12/02/2010 9
RDXX0SZR DWDM XFP Transceiver Product Specifications
6. Outline Drawings
Dimensions are in millimeters
Rev A.0, 12/02/2010 10
RDXX0SZR DWDM XFP Transceiver Product Specifications
7. PCB layout and Bezel recommendation
Dimensions are in millimeters
XFP Host Board Mechanical Layout
Rev A.0, 12/02/2010 11
RDXX0SZR DWDM XFP Transceiver Product Specifications
PCB layout and Bezel recommendation (continued)
XFP Host Board Mechanical Layout
Recommended Single Sided Bezel Design
Rev A.0, 12/02/2010 12
RDXX0SZR DWDM XFP Transceiver Product Specifications
8. SFP+ Block Diagram, Power Supply Information and Host Board Interface
8.1 XFP Block Diagram and Host Board Interface
Note 1: Host board output device circuit in the transmitter side and host board input device circuit in the receiver should be
carefully designed to meet 100ohm differential impedance matching. Also necessary is the dc bias circuit of each
input and output by taking into account of ac coupling of data input ant output of XFP module. For the interface of
host board devices, it is recommended to refer to the device vendor’s data sheet.
TOSA
ROSA
Laser
Post amp.
Module
GND
RD-
RD+
TD+
TD-
Tx Disable
SCL SDA EEPROM
100Ω
Management processor
Zin diff.=
100Ω
Zout = 50Ω
each arm
Pin 5
Pin 29
Pin 28
Pin 1, 7, 15, 16,
19, 23, 26, 27
Pin 10 Pin 11
Pin 17
Pin 18
R= 4.7k ~ 10kΩ SCL. SDA
VCC3
Mod_Abs, Mod_NR
Mod_DeSel, P_Down/RST
R R
R Interrupt, RX_LOS
Pin 10, 11 Pin 12, 13
Pin 4,14
Pin 3, 21 VCC3
VCC5
VEE5
Pin 8, 9
Pin 6
Pin 2 (Not used)
VCC2 Pin 22 (Not used)
RefCLK+/- Pin 24,25 (Not used)
Rev A.0, 12/02/2010 13
RDXX0SZR DWDM XFP Transceiver Product Specifications
8.2 Recommended Host Board Supply Filtering Network
9. Digital Diagnostic Monitoring and Serial ID Operation
Serial ID and Map: page A0h
Address HEX Name of Fields Description
0 06 Identifier [06h] XFP
1 00
Signal Conditioner Control Field
[7-4] Data Rate Control
[2] Lineside Loopback
[1] XFI Loopback
[0] Signal Conditioner Control
Signal Conditioner Control Field
Data Rate Control(01[7:4]) = 9.50 Gb/s
[0b] Normal Operation
[0b] Normal Operation
[0b] Normal Asynchronous REFCLK mode
2 varies Temp High Alarm MSB ST: 78 [], ET and IT: 88 []
3 varies Temp High Alarm LSB
4 varies Temp Low Alarm MSB ST: -13 [], ET and IT: -43 []
5 varies Temp Low Alarm LSB
6 varies Temp High Warning MSB ST: 75 [], ET and IT: 85 []
7 varies Temp High Warning LSB
8 varies Temp Low Warning MSB ST: -10 [], ET and IT: -40 []
9 varies Temp Low Warning LSB
10-17 00 Reserved A/D Flag Thresholds(10-17)
18 FF Bias High Alarm MSB 131 [mA]
19 DC Bias High Alarm LSB
20 3A Bias Low Alarm MSB 30 [mA]
21 98 Bias Low Alarm LSB
22 EC Bias High Warning MSB 121 [mA]
23 54 Bias High Warning LSB
24 44 Bias Low Warning MSB 35 [mA]
25 5C Bias Low Warning LSB
26 9B TX Power High Alarm MSB 6.0 [dBm]
27 83 TX Power High Alarm LSB
28 0C TX Power Low Alarm MSB -5.0 [dBm]
29 5A TX Power Low Alarm LSB
4.7µH
4.7µH
0.1µF
0.1µ 22µF 0.1µF
VCC3
XFP Module
Vcc3
Vcc5
HOST BOARD
22µF 0.1µF
VCC5
Rev A.0, 12/02/2010 14
RDXX0SZR DWDM XFP Transceiver Product Specifications
30 62 TX Power High Warning MSB 4.0 [dBm]
31 1F TX Power High Warning LSB
32 13 TX Power Low Warning MSB -3.0 [dBm]
33 94 TX Power Low Warning LSB
34 0C RX Power High Alarm MSB -5.0 [dBm]
35 5A RX Power High Alarm LSB
36 00 RX Power Low Alarm MSB -27.0 [dBm]
37 14 RX Power Low Alarm LSB
38 07 RX Power High Warning MSB -7 [dBm]
39 CB RX Power High Warning LSB
40 00 RX Power Low Warning MSB -25 [dBm]
41 20 RX Power Low Warning LSB
42 3C AUX 1 High Alarm MSB (Laser Temp) 60 []
43 00 AUX 1 High Alarm LSB (Laser Temp)
44 0A AUX 1 Low Alarm MSB (Laser Temp) 10 []
45 00 AUX 1 Low Alarm LSB (Laser Temp)
46 32 AUX 1 High Warning MSB (Laser Temp) 50 []
47 00 AUX 1 High Warning LSB (Laser Temp)
48 14 AUX 1 Low Warning MSB (Laser Temp) 20 []
49 00 AUX 1 Low Warning LSB (Laser Temp)
50 D6 AUX 2 High Alarm MSB (Power Supply) 5.5 [V]
51 D8 AUX 2 High Alarm LSB (Power Supply)
52 AF AUX 2 Low Alarm MSB (Power Supply) 4.5[V]
53 C8 AUX 2 Low Alarm LSB (Power Supply)
54 CF AUX 2 High Warning MSB (Power Supply) 5.3[V]
55 08 AUX 2 High Warning LSB (Power Supply)
56 B7 AUX 2 Low Warning MSB (Power Supply) 4.7[V]
57 98 AUX 2 Low Warning LSB (Power Supply)
58 00
VPS Fields
[7-4] Lowest Voltage Supported
with an Operational LV Regulator
[3-0] Voltage Supplied on the VCC2 Pins
Not Supported
59 00
VPS Fields
[7-4] Voltage Supported
with a Bypassed Regulator
[0] Regulator bypass mode
Not Supported
60-69 00
70 00 Acceptable BER Not Supported
71 00 Actual BER Not Supported
72 00 Wavelength Set MSB(72-73) Not Supported
73 00
74 00 Wavelength Error LSB(74-75) Not Supported
75 00
76 80 Amplitude Adjustment 0.00 [%]
77 00 Phase Adjustment Not Supported
78 00 Reserved(78-79)
79 00
80 xx
Latched Interrupt Flag Fields(80)
[7] L-Temp High Alarm
[6] L-Temp Low Alarm
[3] L-TX Bias High Alarm
[2] L-TX Bias Low Alarm
[1] L-TX Power High Alarm
Varies
Rev A.0, 12/02/2010 15
RDXX0SZR DWDM XFP Transceiver Product Specifications
[0] L-TX Power Low Alarm
81 xx
Latched Interrupt Flag Fields(81)
[7] L-RX Power High Alarm
[6] L-RX Power Low Alarm
[5] L-AUX 1 High Alarm
[4] L-AUX 1 Low Alarm
[3] L-AUX 2 High Alarm
[2] L-AUX 2 Low Alarm
Varies
82 xx
Latched Interrupt Flag Fields(82)
[7] L-Temp High Warning
[6] L-Temp Low Warning
[3] L-TX Bias High Warning
[2] L-TX Bias Low Warning
[1] L-TX Power High Warning
[0] L-TX Power Low Warning
Varies
83 xx
Latched Interrupt Flag Fields(83)
[7] L-RX Power High Warning
[6] L-RX Power Low Warning
[5] L-AUX 1 High Warning
[4] L-AUX 1 Low Warning
[3] L-AUX 2 High Warning
[2] L-AUX 2 Low Warning
Varies
84 xx
Latched Interrupt Flag Fields(84)
[7] L-TX_NR
[6] L-TX_Fault
[5] L-TX CDR
[4] L-RX_NR
[3] L-RX_LOS
[2] L-RX CDR
[1] L-MOD_NR
[0] L-Reset
Varies
85 xx
Latched Interrupt Flag Fields(85)
[7] L-APD Supply Fault
[6] L-TEC Fault
[5] L-Wavelength Unlocked
Varies
86 xx
Latched Interrupt Flag Fields(86)
[7] L-VCC5 High Alarm
[6] L-VCC5 Low Alarm
[5] L-VCC3 High Alarm
[4] L-VCC3 Low Alarm
[3] L-VCC2 High Alarm
[2] L-VCC2 Low Alarm
[1] L-Vee5 High Alarm
[0] L-Vee5 Low Alarm
Varies
Rev A.0, 12/02/2010 16
RDXX0SZR DWDM XFP Transceiver Product Specifications
87 xx
Latched Interrupt Flag Fields(87)
[7] L-VCC5 High Warning
[6] L-VCC5 Low Warning
[5] L-VCC3 High Warning
[4] L-VCC3 Low Warning
[3] L-VCC2 High Warning
[2] L-VCC2 Low Warning
[1] L-Vee5 High Warning
[0] L-Vee5 Low Warning
Varies
88 00
Interrupt Masking Bits(88)
[7] M-Temp High Alarm
[6] M-Temp Low Alarm
[3] M-TX Bias High Alarm
[2] M-TX Bias Low Alarm
[1] M-TX Power High Alarm
[0] M-TX Power Low Alarm
Varies
89 00
Interrupt Masking Bits(89)
[7] M-RX Power High Alarm
[6] M-RX Power Low Alarm
[5] M-AUX 1 High Alarm
[4] M-AUX 1 Low Alarm
[3] M-AUX 2 High Alarm
[2] M-AUX 2 Low Alarm
Varies
90 00
Interrupt Masking Bits(90)
[7] M-Temp High Warning
[6] M-Temp Low Warning
[3] M-TX Bias High Warning
[2] M-TX Bias Low Warning
[1] M-TX Pow.High Warning
[0] M-TX Pow.Low Warning
Varies
91 00
Interrupt Masking Bits(91)
[7] M-RX Pow.High Warning
[6] M-RX Pow.Low Warning
[5] M-AUX 1 High Warning
[4] M-AUX 1 Low Warning
[3] M-AUX 2 High Warning
[2] M-AUX 2 Low Warning
Varies
92 00
Interrupt Masking Bits(92)
[7] M-TX_NR
[6] M-TX_Fault
[5] M-TX CDR not Locked
[4] M-RX_NR
[3] M-RX_LOS
[2] M-RX CDR not Locked
[1] M-MOD_NR
[0] M-Reset Complete
Varies
93 00
Interrupt Masking Bits(93)
[7] M-APD Supply Fault
[6] M-TEC Fault
[5] M-Wavelength Unlocked
Varies
Rev A.0, 12/02/2010 17
RDXX0SZR DWDM XFP Transceiver Product Specifications
94 00
Interrupt Masking Bits(94)
[7] M-VCC5 High Alarm
[6] M-VCC5 Low Alarm
[5] M-VCC3 High Alarm
[4] M-VCC3 Low Alarm
[3] M-VCC2 High Alarm
[2] M-VCC2 Low Alarm
[1] M-Vee5 High Alarm
[0] M-Vee5 Low Alarm
Varies
95 00
Interrupt Masking Bits(95)
[7] M-VCC5 High Warning
[6] M-VCC5 Low Warning
[5] M-VCC3 High Warning
[4] M-VCC3 Low Warning
[3] M-VCC2 High Warning
[2] M-VCC2 Low Warning
[1] M-Vee5 High Warning
[0] M-Vee5 Low Warning
Varies
96 xx Case Temperature MSB (Module Temp) Varies
97 xx Case Temperature LSB (Module Temp) Varies
98-99 00 Reserved(98-99)
100 xx TX Bias MSB Varies
101 xx TX Bias LSB Varies
102 xx TX Power MSB Varies
103 xx TX Power LSB Varies
104 xx RX Power MSB Varies
105 xx RX Power LSB Varies
106 xx LD Temp monitor MSB Varies
107 xx LD Temp monitor LSB Varies
108 xx Vcc(+5.0V) Supply Voltage MSB Varies
109 xx Vcc(+5.0V) Supply Voltage LSB Varies
110 xx
Control/Status Bits
[7] TX Disable State
[6] Soft TX Disable
[5] MOD_NR State
[4] P_Down State
[3] Soft P_Down
[2] Interrupt
[1] RX_LOS
[0] Data_Not_Ready
Varies
111 xx
Control/Status Bits
[7] TX_NR State
[6] TX_Fault
[5] TX_CDR
[4] RX_NR
[3] RX_CDR
Varies
112-117 00
118 00 Pcket Error Checking
[0] Error Checking [0b] Disable Packet Error Checking
119-126 00
127 01 Table Select
128 06 Identifier [06h] XFP
Rev A.0, 12/02/2010 18
RDXX0SZR DWDM XFP Transceiver Product Specifications
129 98 Extended Identifier
[10b] Power Level 3 Module (3.5W max.power
dissipation.)
[0] Module with CDR function
[1] TX Ref Clock Input Not Required
[1] CLEI code present in Table 02h
130 07 Connector [07h] LC
131 00 Gigabit Ethernet Compliance
132 00 Gigabit Fibre Channel Compliance
133 00 Gigabit Copper Links
134 00 Lower Speed Links
135 00 SONET/SDH Codes -Interconnect
136 00 SONET/SDH Codes Short Haul
137 42 SONET/SDH Codes Long Haul L-64.2a, WDM
138 00 SONET/SDH Codes Very Long Haul
139 10 Encoding [4] NRZ
140 64 BR,MINIMUM 9.950 [Gbits/s]
141 6F BR,MAXIMUM 11.300 [Gbits/s]
142 50 LENGTH (Km) 80 [Km]
143 00 LENGTH (EXT. 50 uM MULTIMODE FIBER) 0 [m]
144 00 LENGTH (50 uM MULTIMODE FIBER) 0 [m]
145 00 LENGTH (62.5 uM MULTIMODE FIBER) 0 [m]
146 00 LENGTH (COPPER) 0 [m]
147 76 Device Technology
[0111b] 1550 nm EML
[0b] Transmitter not Tunable
[1b] APD detector
[1b] Cooled transmitter
[0b] No wavelength control
148 4F
VENDOR NAME(148-163)
O (OE SOLUTION )
149 45 E
150 20
151 53 S
152 4F O
153 4C L
154 55 U
155 54 T
156 49 I
157 4F O
158 4E N
159 53 S
160-163 20
164 F8 CDR Support
[7] CDR support for 9.95 Gb/s
[6] CDR support for 10.3 Gb/s
[5] CDR support for 10.5 Gb/s
[4] CDR support for 10.7 Gb/s
[3] CDR support for 11.1 Gb/s
165 00
VENDOR OUI(165-167)
00
166 19 19
167 3A 3A
168 52 VENDOR PN(168-183) R (RDXX0SZR-xxx)
169 44 D
170 58 X
Rev A.0, 12/02/2010 19
RDXX0SZR DWDM XFP Transceiver Product Specifications
171 58 X
172 30 0
173 53 S
174 5A Z
175 52 R
176 2D -
177 TBD TBD
178 TBD TBD
179 TBD TBD
180-183 20
184 31 VENDOR REV(184-185) 1 (1 )
185 20
186 79 LASER WAVELENGTH(186-187) 1550.00 [nm](to be modified)
187 18
188 00 WAVELENGTH TOLERANCE(188-189) 0.236 [nm]
189 2F
190 xx MAXIMUM CASE TEMPERATURE xx=(46h for ST, 55h for ET and IT)
191 xx Check code for addresses 120 to 190 Varies
192 AF Maximum Power Dissipation 3500 mW
193 1E Maximum Total Power
Dissipation in Power Down Mode 300 mW
194 95
[7-4] Maximum current required
by +5V Supply.
[3-0] Maximum current required
by +3.3V Supply.
420 mA
480 mA
195 00
[7-4] Maximum current required
by +1.8V Supply.
[3-0] Maximum current required
by -5.2V Supply
0 mA
0 mA
196-211 xx VENDOR SN(196-211) Varies
212-219 xx Date Code(212-219) Varies
220 00
Diagnostic Monitoring Type
[4] Module Respond to FEC BER
[3] Received power measurement type
221 60
Enhanced Options
[7] Module Supports Optional VPS
[6] Soft TX_DISABLE
[5] Soft P_down
[4] Supports VPS LV regulator mode
[3] Supports VPS bypassed regulator Mode
[2] Active FEC control functions
[1] Wavelength tunability
[0] Optional CMU Support Mode
[6] Optional Soft TX_DISABLE implemented
[5] Optional Soft P_down
222 46
Auxiliary A/D Types
[7-4] Aux A/D Input 1
[3-0] Aux A/D Input 2
[0100b] Laser Temperature
[0110b] +5.0V Supply Voltage
223 xx Check code for addresses 192 to 222 Varies
224-255 FF VENDOR SPECIFIC ID FIELD(224-255) TBD
Rev A.0, 12/02/2010 20
RDXX0SZR DWDM XFP Transceiver Product Specifications
10. Digital Diagnostics Monitor Accuracy
Parameter Accuracy Range
Temperature +/- 3 oC -40 to 102 (
oC)
Voltage +/- 3% 0 to Vcc (V)
Tx bias Current +/- 10% 0 to 120 (mA)
Tx power +/- 2dB -2 to +3 (dBm)
Rx Power +/- 2dB -26 to -6 (dBm)
TEC Current +/- 60mA -1200 to 1200 (mA)
TEC Temperature 1 +/- 0.25
oC 20 to 70 (
oC)
Note 1: Relative Accuracy. Absolute accuracy is +/- 3 oC
11. Regulatory Compliance
RDXX0SZR comply with international Electromagnetic Compatibility (EMC) and international safety
requirements and standards. EMC performance is dependent on the overall system design. The RDXX0SZR is
lead-free and RoHS-compliant per Directive 2002/95/EC of the European Parliament and of the Council of 27
January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
12. Ordering Information
Model Name OES P/C Operating Case Temperature
Latch Color
Application Distance
RDXX0SZR-Sxx Dxx02 0oC to 70oC White SONET/SDH & 10G GbE 80km
RDXX0SZR-Exx TBD -5oC to 85oC White SONET/SDH & 10G GbE 80km
RDXX0SZR-Ixx Dxx04 -40oC to 85oC White SONET/SDH & 10G GbE 80km
Notice: This data sheet is subject to change at any time without notice.
13. Revision History
Date Rev. # Description Author(s)
12/01/2010 A.0 Initial Release JSYU/KSP
Contact Information:
OE Solutions Co. Ltd. (Korea) Techno Park, 958-3, Daechon-Dong, Buk-Gu, Gwangju, Korea, 500-470. Tel: +82-62-602-7813, Fax: +82-62-602-7639, www.oesolution.com.
OE Solutions America, Inc. 560 Sylvan Avenue, 1
st Floor, Englewood Cliffs, NJ 07632
Tel: 201-568-1188 Fax:201-568-1177Tel: +1-201-224-2377, Fax: 1-949-272-3200