7/27/2019 03 - Rules of Labor Protection
1/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 2 - Rules of Labor Protection
~ Chapter 3 ~
Rules of Labor Protection
7/27/2019 03 - Rules of Labor Protection
2/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 3 - Rules of Labor Protection
Rules of labor protection
1. At the work execution some rules will be followed:
a. The Norms of Labor Protection elaborated based on the Law no. 90 from
25.06.1996 and promulgated through Decree no.290 from 11.06.1996.
b. The standing order regarding the labor protection and industrial sanitation in
constructions published in the Constructions Gazette approved by MLPAT with Ord.
9/N/15.03.1993
c. Labor protection norms in constructions montage activity approved cu Ord.
M.C. Ind. Nr. 1233/D/29.12.1980
d. IM006/1996 The specific labor protection norms for masonry, prefabricated
montage and finishing works in constructions.
e. The law no. 90/1996 The law regarding labor protection and industrial
sanitation
f. General labor protection norms edited by the Work and Social Protection
Minister in collaboration with Health Minister
g. STATS 26112/87protection against electric shock
h. STATS 12216-84 protection against electric shock at the portable electric
equipment
i. STAS 12217-88 protection against electric shock at the mobile electric
equipment
j. Specific Labor Security Norms for works at highnessDecree 235/26.07.1995
k.
Specific Labor Security Norms for preparing, transport, and pouring concrete and
execution of reinforced and precast concrete worksDecree 136/17.04.1995
It is admonished on the detailed attribution of the provided technologies for each work,
with whole gang, on the organization and endowment of the working place with tools and
corresponding equipment for accomplishing the labor protection briefing to all the workers,
7/27/2019 03 - Rules of Labor Protection
3/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 4 - Rules of Labor Protection
periodically and when changing the working place, the permanent verification of well-condition
and working state of the tools, devices and equipment.
By working at height it is understand the activity performed at minimum 2 m measured
from workers foot until the reference natural base (the ground level) or any other artificial base
from which the risk of falling exist.
For the works execution at height some things have to taken into consideration:
- the preliminary technological organization of the works at height by the collective
insurance of all working conditions during the entire period of works development;
- the endowment with individual protection equipment according to the conditions
from the working place so that the safety of executor to be insured;
- the compulsory initiation, training and usage of collective and individual
endowments corresponding to the working place and respective works risks;
Working at height is allowed only if the working place was improved and endowed from
technical and organizational point of view. The access to and from the working place placed at
height must be insured against falling of the workers,
The workers must use the constructors and assembler safety belt, according to the present
norms. The anchorage point must be chosen so that the fixing zone of the worker to be under the
level of the anchorage place during the whole period of work. The safety belt must be checked
before using it. For working at height it is compulsory the usage ofcrash helmet. Before starting
the works, the worker has to check the integrity of the helmet, of the damping system and of the
fixing belts.
The works have to be developed only under surveillance; the person nominated for
surveillance must check before starting the work if the all the necessary safety measures were
insured.
The inclined beams, plans and platforms used in materials handling must be resistant and
provided with safe catching and fixing devices, any displacement during the works being
forbidden. They will have a slope of maximum 20% and a width of minimum 1 m. They will be
7/27/2019 03 - Rules of Labor Protection
4/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 5 - Rules of Labor Protection
provided with high balusters of 1 m with intermediate bonds and with lateral borders of 10-15
cm.
The ascension ramps will have a slope of maximum 1:3 and at every 30-40 cm some
wood laths will be fixed on the whole width of the ramp. It is forbidden the blockage of the
access ramp with building materials or any other objects. The ramps must be permanently
maintained and cleaned.
For using the scaffoldings, formworks and centrings there will be applied the previsions
from the Specific Labor Security Norms for formwork, centrings and scaffoldings works.
The quality of the wood materials must correspond to the project. The floorings made of
steel are made from expanded or ribbed steel sheeting. The joints between the panels or the
bordages of the floorings have maximum 10 cm width. On the floorings surface in the slope or in
the curved part some wood laths will be fixed at a distance of 30-40 cm, against sliding.
The fixing the flooring on the supports will be made such that the possibility of
displacement or sliding to be excluded. The floorings will not be placed on cantilevers.
The usage of installations, devices and tools for working at height is allowed only if the
working instructions and the labor security are adapted to the site conditions. At the working
place at height there must be lifted only materials which are absolutely necessary.
The necessary tools for execution of different operations must be kept in special pockets
or in sheaths fixed on the safety belt. The tools and the materials must be lifted gradually,
according to the necessity, with a helping rope, being forbidden their throwing from the ground
level to the working position or vice versa.
At the elaboration of the site organization project, there must be envisaged a series of
measures which would insure the labor safety:
- the enclosure of the site with definitive or inventory elements;
- the leveling of the ground before starting the works;
7/27/2019 03 - Rules of Labor Protection
5/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 6 - Rules of Labor Protection
- the enclosure of the dangerous areas on the site (places where montage works are
executed, the action radius of the cranes, the place where the scaffoldings are dismounted, the
slaking pits etc.);
- the trenches or the channels with a depth larger than 1 m will be provided with
walkways for passengers having the minimum width of 0.7 m and with balustrades (on both
sides) of 1 m height and wood boards of 15-18 cm;
- the enclosure of the holes, shafts, deep trenches, of the holes from the floors etc.;
- the insurance of rainwater removal through drainage trenches.
Measures taken for the labor security at the concreting works
- the operations of charging/discharging the materials and the equipment used for
concreting works will be made only in the places mentioned in the site organization or in the
special authorized or established polygons;
- the access of the workers under the concrete mixing bucket is forbidden when it is
lifted;
- the cleaning, the maintaining and the repair of the concrete mixing are allowed
only after the machine has stopped and has been disconnected from the power;
- the transport of concrete on the scaffoldings will be made on floorings of
minimum 1.2 m width, with balusters and borders on the edges; the wholes from the floorings
through which the concrete is poured must be covered when concrete pouring works are not
performed;
- when the concrete is transported on the vertical direction it is forbidden the
stopping of the workers under and in incidence of the lifting device;
- when discharging the concrete it is forbidden the workers ascension on the
concrete mixer; the concrete stuck on the bucket will be removed with shovels with long
handles;- the concrete pump will be placed towards the working place such that the
mechanic to have visibility to the concreting place;
- the pump or the pipe for the concrete transport is dismounted only after the
equipment stopped functioning; during the cleaning of the pipe the workers must move away at a
7/27/2019 03 - Rules of Labor Protection
6/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 7 - Rules of Labor Protection
distance of 10 m from this place, and in the front of the evacuation hole is mounted an inclined
shield;
- in case of the concrete pouring from a height greater than 1.5 m, the working
floorings must be enclosed with balusters and wood boards on the edges;
- when poring concrete on surfaces with a slope greater than 300 the concreters
must wear safety belts tied through ropes by the resisting elements of the construction;
- in case of pouring concrete with concrete buggy there will followed the
instructions for the use of these devices; before work starting, the technical condition of the
concrete buggies and the devices and accessories, including the hanging device will be checked;
- it is forbidden for the workers to stay under the concrete bucket;
- in case of the blockage of the concrete buggy, this will be cleaned only when it is
placed on the ground and insured against turning over;
- the electrical equipment necessary for putting into service the compactors will be
made taking into consideration the technical labor security rules for electric equipment;
- the framework of the vibrator will be tied to the ground and the workers must
wear electric insulator boots and gloves; the electric wires which charge the vibrator with
electricity must be flexible and insulated in rubber tube;
- it is forbidden the access of the people in the area close to the construction where
it is possible the concrete falling during the pouring;- on cold time the walkways for people, the charging/discharging floorings, the
runways, the access ramps must be cleaned from ice or snow and dotted with sand or slag; in the
case of steam heating there must taken some measures against workers accidents with steam or
by touching the distribution pipes;
- the straightening of the reinforcement must be made in another place, enclosed
and marked with warning plates;
- the removal of the metallic dust and the rust resulted from the cutting and bending
reinforcement is made using brushes, brooms or air exhausters; it is forbidden the removal of this
dust by hand or by mouth blowing out;
- the welding of the reinforcement and the steel frameworks is made taking into
consideration the norms regarding the welding works;
7/27/2019 03 - Rules of Labor Protection
7/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 8 - Rules of Labor Protection
- it is forbidden the execution on the bottom of the formwork the montage of the
reinforcement or of the steel frameworks in beams or in other isolated elements;
- it is forbidden the circulation and the montage of the reinforcement on the floors
formworks before these were first well consolidated and checked
For preventing fires the following norms will be applied:
- Decree no. 775/198General norms for preventing and extinction of fires
- H.G.R. 51- 1992, 1996 Measures for improvement the activities of preventing
and extinction of fires;
- H.G.R. 448/2002 Construction categories which submit themselves to
authorization P.S.I.
- P 118-99Norm for fire safety of constructions;
- STAS 11841/83Safety measures against fires. Types of fires
- STAS 6647/88 Safety measures against fires. Fire resistant elements for holes
protection for walls and plates;
- O.G. nr. 60/1997 Regarding defense against fires, approved with the law no.
212/1997
- C 300/94 Norm for preventing and extinction of fires during the construction
works and the installation for those M.L.P.A.T. 20/N 11.07.94B.C. 9/94;
A person responsible of P.S.I. will be named and trained and intervention teams will be
organized (on shifts).
During the works, there will be placed in visible and marked places, known by all the
execution personal:
- at least a panel P.S.I. fully endowed;
- minimum 2 fire extinguishers in working state (1 piece/100 m2)
- a water supply network with the possibility to be used in case of fires;
7/27/2019 03 - Rules of Labor Protection
8/8
July 2013 Technical University "Gheorghe Asachi" of Iai Giosan Cosmin Constantin
- 9 - Rules of Labor Protection
In order to evacuate the personal in case of a fire, besides the usual circulation ways
made of incombustible materials and permanently lightened, at least 2 stairs on chains (or steel
cable) will be mounted in different places.
The smoking is allowed only in special installed places.
The electric installations and equipment used are examined every day by an electrician
trained for this purpose, which will repair every detected defection; they will be adequately
isolated such that not a short circuit to appear.
The signaling and fire extinction installations are designed and made according to
technical rules so that they present the exploitation safety, to insure the possibility of periodical
checking of the working states and eventual revision and repairs to be easily made.