7
Z-E2026 DEVICE INSTALLATION MANUAL EN

Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

  • Upload
    others

  • View
    22

  • Download
    2

Embed Size (px)

Citation preview

Page 1: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

Z-E2026

DEVICE INSTALLATION MANUAL EN

Page 2: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

2

COMPATIBILITY LISTModel Model Version Model YearVW Polo 6R 2010 – 2014VW EOS 1F from 2006VW Scirocco III 13 from 2008VW Beetle Coupé 5C from 2011VW Beetle Cabrio 5C from 2012VW Golf V 1K 2003 – 2008VW Golf V Variant 1K 2007 – 2009VW Golf VI 5K 2008 – 2012VW Golf VI Variant AJ 2009 – 2013VW Jetta 1K/16 from 2005VW Golf Cabrio 51 2011 – 2015VW Golf Plus 5M/52 from 2005VW Passat 3C/36 2005 – 2014VW Passat Variant 3C/36 2005 – 2014VW Passat Alltrack 36 2012 – 2014VW Passat CC 35 2008 – 2012VW CC 35 from 2012VW Touran 1T 2003 – 2015VW Sharan 7N from 2010

VW Tiguan 5N 2007 – 2012VW Amorak 2H from 2010VW Caddy 2K/2C 2003 – 2012VW T5 7E/7J 2010 – 2015VW T6 SG/SF from 2015SEAT Leon 1P 2005 – 2012SEAT Toledo 5P 2004 – 2009SEAT Toledo KG 2012 – 2015SEAT Altea 5P from 2004SEAT Altea XL 5P from 2006SEAT Altea Freetrack 5P from 2007SEAT Alhambra 71 from 2010SKODA Rapid NH from 2013SKODA Rapid Spaceback NH from 2013SKODA Octavia II 1Z 2009 – 2013SKODA Octavia II Combi 1Z 2009 – 2013SKODA Octavia II Scout 1Z 2009 – 2013SKODA Superb II 3T 2008 – 2015SKODA Superb II Combi 3T 2008 – 2015SKODA Yeti 5L from 2009

Radio

QUADLOCK IIRadio

QUADLOCK III

Navigation

Navigation

Page 3: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

3

● The installation of the ZENEC system should be carried out by an authorized installer. Specific knowledge and tools are required to do the installation. Incorrect installation can cause damage to the vehicle and the ZENEC system.● Correct functioning can only be guaranteed when you use the ZENEC original accessories included in the kit or those optionally available. The ZENEC system and the original accessories must under no circumstances be modified or altered in any way. Inappropriate actions can cause damage to the vehicle and the ZENEC system.

● Torx screwdriver T25● Release tool for original radio / navigation system ● Release tool made of plastic● Insulating tape

● The target vehicle must factory configured with one of the radio or navigation systems, listed on the previous page. The ZENEC system is not compatible with vehicles, which are equipped with a hybrid or electro drive ex factory.● This device installation manual applies to vehicle platforms appearing in the compatibility list on the previous page, and in a condition as offered by the respective vehicle manufacturer. Other differing configurations and installations may result in complications and malfunctions. ● The ZENEC system is equipped with an integrated DAB+ receiver. To make use of this you will need a suitable DAB antenna (not included in kit) that must be connected to the ZENEC system. Please pay attention that the device does not have a phantom power for the voltage supply of an active DAB antenna.● If the target vehicle is already equipped with an original DAB antenna, it is still possible to use it in combination with the ZENEC system. Please use the DAB antenna connector (Nr.8), which is include in the kit, for connection.● The ZENEC system is equipped with a AM/FM dual-tuner system (Phase Diversity). If the target vehicle is equipped only with a AM/FM single-tuner system, the optional available accessory “ZENEC ZE-NC-ANT3” is needed for the installation.● Software updates to the ZENEC system are installed with a USB memory device. Therefore when fitting the system make sure that the USB connection of the ZENEC system will still be accessible later (installation of USB extension cable or USB hub).● If you have questions or problems relating to the ZENEC system, please contact the dealer from whom you purchased it.● Additional questions about the compatibility could be answered by using the ZENEC online configurator: www.zenec.com/configurator

TOOLS REQUIRED

No. Article Qty1 ZENEC system 12 microSD card with adapter 13 GPS antenna 14 Bluetooth microphone 15 Main connection cable Quadlock II 1

6 Main connection cable Quadlock III 1

THE KIT INCLUDESNo. Article Qty7 CAN bus interface 1

8 DAB antenna adapter (Fakra – SMB) 1

9 USB extension cable 1 10 24-pin connection cable (4.2, Cam, MZone) 111 18-pin connection cable (Mic, Cam) 112 Double-sided adhesive pad 1

● ZENEC ZE-NC-ANT3 (antenna interface)ADDITIONAL MOUNTING ACCESSORIES

CAUTION

NOTE

Page 4: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

1

4

4

3

2

EXAMPLE OF INSTALLATION GOLF VIREMOVAL WORK AND PREPARATION:

3. Unscrew and remove the four Torx Screws (T25) of the original device.

1. Gently lift the trim frame starting on the right side of OE device. For successful completion of this step, using a release tool made of plastic tool is mandatory.

2. Run the prying tool anticlockwise around the trim frame, to release it from the console. The trim frame should come off of the console completely.

4. Remove the original device by pulling it out of the radio slot. Detach all the cables from its backside.

1. Remove the ignition key and keep it outside the car until the installation is finished. 2. Please wait for ca. 10 minutes until the CAN bus system is completely shut down, before you start

with the deinstallation of the original device. 3. Now you can start with the deinstallation of the original device.4. Please switch on the ignition only, when all work steps are done and the ZENEC system is

completely mounted.

NOTE

Page 5: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

8

5

9

INSTALLATION: 5. (No picture) Fit the GPS antenna (No. 3) at a suitable place,

and make sure that the GPS reception is not adversely affected due to shadowing by metallic vehicle parts (thermal glazing etc.). Next run the connecting cable to the radio slot.

6. (No picture) If you wish to use it, now fit the external Blue-

tooth microphone (No. 4) supplied, and run the connecting cable to the radio slot. Depending on preference and on choice of an external or device-internal microphone, the microphone source for the Bluetooth mode must be corre-spondingly changed in the device menu.

7. (No picture) Run the USB extension cable (No. 9) from the

radio slot to the position you want.

8. Connect one of the main connection cables

(No. 5 or No. 6) of the ZENEC system (No. 1) to the Quadlock connector of the car and close its locking mechanism. Please pay attention to the compatibility list in this document to choose the suitable main connection cable, including in the delivery, for your vehicle. Following this, connect the CAN bus interface (No. 7) to the main con-nection cable.

9. Before installing the ZENEC system (No. 1)

remove the two transport securing screws.

Page 6: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

6

10

11

12

COMMISSIONINGMake sure that the vehicle is located outside, and that the GPS reception is not adversely affected by any shadowing (trees, high buildings etc.). Now insert the navigation software SD card (No. 2) supplied into the microSD card slot of the ZENEC system, and start it in order to establish a sat fix. Make sure that the vehicle is not moved until the sat fix is established. Now press the NAV button to start the navigation mode, and choose map view. Once your present location can be seen in the map view the sat fix has been established. This can take 3 to 5 minutes. You can now use the ZENEC system.

Finally carry out a general functional test and perform the basic and car specific settings (AC, OPS etc.). Also ensure that no fault warnings appear on the vehicle side.

12. Press the trim frame back on to make the instal-lation complete.

● Make sure that all connectors at the rear of the ZENEC system have sufficient room and are not bent.● Connectors without a retaining mechanism must be additionally secured with insulating tape.● If the navigation arrows are not present in the multi-functional display MFA+, although the needed data are available via the CAN bus system, you have to unlock them first. Please contact a qualified specialist workshop in such a case. Inappropriate actions can cause damage to the vehicle and the ZENEC system.

11. Neatly arrange the wires to the side, making room for the ZENEC system. Carefully slide it into the radio slot and fix it in place, using the four original Torx screws.

10. Connect all the cables to the ZENEC system (No. 1): those previously run in the radio slot, and the original antenna cables.

NOTE

Page 7: Z-E2026 - ZENEC · VW Polo 6R 2010 – 2014 VW EOS 1F from 2006 VW Scirocco III 13 from 2008 VW Beetle Coupé 5C from 2011 VW Beetle Cabrio 5C from 2012 VW Golf V 1K 2003 – 2008

Tech

nica

l mod

ifica

tions

exc

epte

d. N

o lia

bilit

y gr

ante

d fo

r prin

ting

erro

rs.

© C

opyr

ight

201

8 · R

evB

/ cop

y de

adlin

e: Q

2-20

18 ·

Eng

lish

ZENEC · Bohrturmweg 1 · CH-5330 Bad Zurzach · Schweiz/Switzerland · Mail: [email protected] · www.zenec.com

KL 31 / Power GND B12 C15KL 30 / Constant +12V PWR B15 C16CAN-Bus B8 C41CAN-Bus B9 C42Loudspeaker rear right (+) B1 C1Loudspeaker front right (+) B2 C2Loudspeaker rear right (-) B5 C5Loudspeaker front right (-) B6 C6Loudspeaker rear left (+) B4 C4Loudspeaker front left (+) B3 C3Loudspeaker rear left (-) B8 C8Loudspeaker front left (-) B7 C7

A1 KL 31 / Power GNDA2 KL 30 / Constant +12V PWR A3 KL 15 / Switched +12V PWRA4A5 Switched +12V amp PWR*A6A7A8A9 Loudspeaker rear right (+)A10 Loudspeaker front right (+)A11 Loudspeaker rear right (-)A12 Loudspeaker front right (-)A13 Loudspeaker rear left (+)A14 Loudspeaker front left (+)A15 Loudspeaker rear left (-)A16 Loudspeaker front left (-)

CONNECTION DIAGRAM

A

C

AM/FM

DAB

GPS

D E

A10 A12 A14 A16A2 A4 A6 A8

A9 A11 A13 A15A1 A3 A5 A7

A9 Speaker Rear Right (+)A10 Speaker Front Right (+)A11 Speaker Rear Right (-)A12 Speaker Front Right (-)A13 Speaker Rear Left (+)A14 Speaker Front Left (+)A15 Speaker Rear Left (-)A16

B1B2B5B6B4B3B8B7

C1C2C5C6C4C3C8C7Speaker Front Left (-)

A1 B12B15

C15C16

QII QIIIQ II Q IIIKL 31 / Power GND

A2 KL 30 / Constant +12V PWR A3 KL 15 / Switched +12V PWRA4A5 Switched +12V amplifier PWR*A6A7A8 Reverse

Serial No.

EU Legal Representative: ACR S & V GmbH · Industriestr. 35 · D-79787 Lauchringen / Germany

*Manufactured under license from Dolby laboratories. "Dolby" and the double-D symbol are trademarks of Dolby laboratories.

10R-05 1776

Rev

. A

CLASS 1 LASER PRODUCT

12V DC / 10 ANEGATIVE

16 PIN CONNECTOR(DEVICE BACKSIDE)

Remove both loader locking screws BEFORE device installation

FM/AM ANTENNA IN:SWITCHED 12V SUPPLY

*300mA max current

NAVICEIVERZ-E2026

QU

AD

LOC

K II

(QII)

C

ON

NEC

TOR

S

QU

AD

LOC

K II

I (Q

III)

CO

NN

ECTO

RS

B1

B2

B3

B4

B5

B8

C1

C4

C5C16

C15

C8

B6

B7

C2

C3C6

C7B15

B12

Cam

era

B

CA F D E

Reve

rse*

ext.

Mic

Pow

er m

ax. 3

00m

A

GN

D

Cam

era

Audi

o

CVBS

In*

CVBS

In*

Line

In R

Line

In L

Vide

o In

Fron

t Out

R

Fron

t Out

L

Rear

Out

R

Rear

Out

L

SUB

(4.2

)CN

T (5

.1)

Out

Subw

oofe

r Out

Vide

o O

ut 1

Vide

o O

ut 2

Line

Out

R

Line

Out

L

*eingebaut miteinander verbunden

Line

In R

Line

In L

P. CN

TR

Reve

rse*

A/V

In

A/V

In

Line

Out

M-Z

one

Quadlock II

FUSE

Quadlock III

A10 A12 A14 A16A2 A4 A6 A8

A9 A11 A13 A15A1 A3 A5 A7

16 PIN CONNECTOR(DEVICE BACKSIDE)

*Internally connected

QU

AD

LOC

K II

I (Q

III)

CO

NN

ECTO

RS

C1

C4

C5C15

C16

C8

C2

C3C6

C7

(see note on DAB antenna page 2)