YAMAHA RXV1500

AV RECEIVER/AV AMPLIFIER

RX-V1500/DSP-AX1500SERVICE MANUALIMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated.

WARNING:

Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.

WARNING:

Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

I CONTENTSTO SERVICE PERSONNEL .......................................... 2 FRONT PANELS ........................................................ 3~4 REAR PANELS .......................................................... 4~7 REMOTE CONTROL ...................................................... 7 SPECIFICATIONS .................................................... 8~11 INTERNAL VIEW ......................................................... 12 DISASSEMBLY PROCEDURES / ......... 13~16 UPDATING FIRMWARE / ..................................... 17~18 SELF DIAGNOSIS FUNCTION (DIAG) / ..................................... 19~43 AMP ADJUSTMENT / ..................... 44~45 DISPLAY DATA ..................................................... 46~47 IC DATA ................................................................. 48~57 BLOCK DIAGRAM ................................................. 58~59 PRINTED CIRCUIT BOARD .................................. 60~74 PIN CONNECTION DIAGRAM .............................. 75~76 SCHEMATIC DIAGRAM ........................................ 77~85 PARTS LIST ......................................................... 87~123 REMOTE CONTROL .......................................... 124~125

RX-V1500/ DSP-AX1500

100919P.O.Box 1, Hamamatsu, Japan'04.09

RX-V1500/DSP-AX1500

I TO SERVICE PERSONNEL1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits.G

WALL OUTLET

EQUIPMENT UNDER TEST

AC LEAKAGE TESTER OR EQUIVALENT

INSULATING TABLEG G

Meter impedance should be equivalent to 1500 ohm shunted by 0.15F.

Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities.

CAUTION F1, F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 125V FUSE. CAUTION F1, F2: REPLACE WITH SAME TYPE 10A, 125V FUSE. ATTENTION F1, F2: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 10A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.

About Lead Free Solder / The P.C.B.s installed in this unit are soldered using the following solder. DSP P.C.B. FUNCTION P.C.B. OPERATION P.C.B. MAIN P.C.B. POWER PC.B. VIDEO P.C.B. CONVERSION P.C.B. Side A Lead Solder Lead Solder Lead SolderSide A

DSP P.C.B. FUNCTION P.C.B. OPERATION P.C.B. MAIN P.C.B. POWER PC.B. VIDEO P.C.B. CONVERSION P.C.B. A B

Side B Lead Free Solder Lead Free Solder Lead Free Solder Lead Free Solder Lead Free Solder Lead Free Solder Lead Free SolderSMT

REFLOW

Process

Solder Dip Side B MI

FLOW

Process

2

Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: 1. As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder.


Sn+Ag+Cu ++ Sn+Cu + Sn+Zn+Bi ++ 30 40

RX-V1500/DSP-AX1500

2. If lead solder must be used, be sure to remove lead free solder from each terminal section of the parts to be replaced and from the area around it completely before soldering, or make sure that the lead free solder and lead solder melt together fully.

I FRONT PANELSRX-V1500 (U, C, A models)

RX-V1500 (R, T, K, L models)

RX-V1500 (B, G models)


3

RX-V1500/DSP-AX1500

DSP-AX1500 (J model)

REAR PANELSRX-V1500 (U, C models)

RX-V1500 (R model)


4

RX-V1500/DSP-AX1500

RX-V1500 (T model)

RX-V1500 (K model)

RX-V1500 (A model)


5

RX-V1500/DSP-AX1500

RX-V1500 (B model)

RX-V1500 (G model)

RX-V1500 (L model)


6

RX-V1500/DSP-AX1500

DSP-AX1500 (J model)

I REMOTE CONTROLRX-V1500 (U, C, R, T, K, A, L models) DSP-AX1500 (J models) RX-V1500 (B, G models)


7

RX-V1500/DSP-AX1500Residual Noise / (IHF-A network) FRONT L/R SP OUT ............................................... 150V or less Channel Separation / (STEREO) PHONO (Input shorted, 1 kHz/10 kHz) ...................... 60dB or more/55dB or more CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) ... 60dB or more/45dB or more Tone Control Characteristics / BASS Boost/Cut .............................................................. 6dB (50Hz) Turnover Frequency ....................................................... 350Hz TREBLE Boost/Cut ............................................................ 6dB (20kHz) Turnover Frequency ...................................................... 3.5kHz Filter Characteristics / FRONT, CENTER, SURROUND, SURROUND BACK SP Small (H.P.F.) ....... fc=40/60/80/90/100/110/120/160/200Hz / 12dB/oct. SUBWOOFER (L.P.F.) ..... fc=40/60/80/90/100/110/120/160/200Hz / 24dB/oct. I Video Section / Video Signal Type (Gray Back) / () U, C, R, K, J models ............................................................ NTSC T, A, B, G, L models ............................................................... PAL Video Signal Type (Video Conversion) / ( ) U, C, R, T, K, A, B, G, L, J models ...................................... NTSC R, T, A, B, G, L models ........................................................... PAL Composite Video Signal Level / ............................................................................ 1 Vp-p / 75 ohms S-Video Signal Level / S Y ......................................................................... 1 Vp-p / 75 ohms C .................................................................. 0.286 Vp-p / 75 ohms Component Video Signal Level / Y ......................................................................... 1 Vp-p / 75 ohms Pb/Cr ............................................................... 0.7 Vp-p / 75 ohms Video Maximum Input Level / ............................................................................ 1.5 Vp-p or more Video Signal to Noise Ratio / ................................................................................. 60 dB or more Monitor Out Frequency Response / Composite Video Signal, S-Video Signal ...... 5 Hz to 10 MHz, -3 dB Component Video Signal ................................ 5 Hz to 60 MHz, -3 dB D4-Video Signal (J model) ............................. 5 Hz to 60 MHz, -3 dB I FM Section / FM Tuning Range U, C models ..................................................... 87.5 to 107.9 MHz T, K, A, B, G models .................................... 87.50 to 108.00 MHz R, L models ......................... 87.5 to 108.0 / 87.50 to 108.00 MHz J model ............................................................... 76.0 to 90.0 MHz 50dB Quieting Sensitivity / 50dB SN (IHF) (1kHz, 100% Mod.) Mono .................................................................. 2.0 V (17.3 dBf) Stereo .................................................................. 25 V (39.2 dBf) Usable Sensitivity / (IHF) Mono .................................................................. 1.0 V (11.2 dBf) Selectivity / at 400 kHz ............................................................................ 70 dB Signal to Noise Ratio / (IHF) Mono / Stereo .......................................................... 76 dB / 70 dB Harmonic Distortion / (1 kHz) Mono/Stereo ................................................................. 0.2 / 0.3 % Stereo Separation / 1 kHz .................................................................................... 42 dB Frequency Response / 20 Hz to 15 kHz .......................................................... +0.5 / -2 dB Antenna Input / ...................................................................... 75 ohms unbalanced I AM Section / AM Tuning Range / U, C models ....................................................... 530 to 1,710 kHz T, K, A, B, G, J models ...................................... 531 to 1,611 kHz R, L models ................................ 530 to 1,710 / 531 to 1,611 kHz Usable Sensitivity / ........................................................................................ 300 V/m Antenna / ................................................................................. Loop Antenna

I SPECIFICATIONS / I Audio Section / Minimum RMS Output Power (Power Amp. Section) / ( ) (20 Hz to 20 kHz) FRONT L/R U, C, R, T, K, A, B, G, L models (0.04% THD, 8 ohms) ... 120W + 120W J model (0.06% THD, 6 ohms) ........................... 120W + 120W CENTER U, C, R, T, K, A, B, G, L models (0.04% THD, 8 ohms) ......... 120W J model (0.06% THD, 6 ohms) ........................................ 120W SURROUND L/R U, C, R, T, K, A, B, G, L models (0.04% THD, 8 ohms) ... 120W + 120W J model (0.06% THD, 6 ohms) ........................... 120W + 120W SURROUND BACK L/R U, C, R, T, K, A, B, G, L models (0.04% THD, 8 ohms) ... 120W + 120W J model (0.06% THD, 6 ohms) ........................... 120W + 120W Maximum Power / (EIAJ, 1kHz, 10% THD) FRONT L/R R, T, K, L models (8 ohms) ................................. 170W + 170W J model (6 ohms) ................................................ 170W + 170W CENTER R, T, K, L models (8 ohms) .............................................. 170W J model (6 ohms) ............................................................. 170W SURROUND L/R R, T, K, L models (8 ohms) ................................. 170W + 170W J model (6 ohms) ................................................ 170W + 170W SURROUND BACK L/R R, T, K, L models (8 ohms) ................................. 170W + 170W J model (6 ohms) ................................................ 170W + 170W Dynamic Power Per Channel / (IHF) U, C, R, T, K, A, L models (8/6/4/2 ohms) ..... 155/195/250/330W DIN Standard Output Power Per Channel / DIN [B, G models] (1 kHz, 0.7% THD, 4 ohms) FRONT L/R ............................................................. 170W + 170W CENTER ............................................................................... 170W SURROUND L/R ..................................................... 170W + 170W SURROUND BACK L/R .......................................... 170W + 170W Dynamic Headroom / U, C, R, T, K, A, L models (8 ohms) .................................. 1.11dB IEC Power / IEC [B, G models] (1 kHz, 0.04% THD, 8 ohms) FRONT L/R ............................................................. 125W + 125W Damping Factor / FRONT L/R (20 Hz to 20 kHz, SPEAKER-A, 8 ohms) .................................................................................... 140 or more Input Sensitivity / Input Impedance (/) PHONO (MM) ................................................. 3.5 mV / 47 k-ohms CD, etc. ......................................................... 200 mV / 47 k-ohms MULTI CH INPUT FRONT L/R, CENTER, SURROUND L/R, SUB WOOFER .................................................................. 200 mV / 47 k-ohms Maximum Input Signal Level / PHONO (MM) (1 kHz, 0.1% THD) ..................................... 100mV CD, etc. (1 kHz, 0.5% THD) .................................................. 2.4V Output Level / Output Impedance (/) REC OUT ..................................................... 200 mV / 1.2 k-ohms PRE OUT (FRONT L/R, CENTER, SURROUND, SURROUND BACK) ................................................................ 1.0 V / 500 ohms SUB WOOFER ................................................... 2.0 V / 500 ohms ZONE 2 OUT U, C, A, B, G models ................................... 1.0 V / 1.2 k-ohms ZONE 3 OUT U, C, A, B, G models ................................... 1.0 V / 1.2 k-ohms Headphone Jack Rated Output / Impedance (/ ) CD, etc. (1 kHz, 40 mV, 8 ohms) ................... 150 mV / 100 ohms Frequency Response / CD, etc. to FRONT L/R (10 Hz to 100 kHz) .................. +0/-3.0dB RIAA Equalization Deviation / RIAA 20 Hz to 20 kHz, PHONO (MM) ...................................... 00.5dB Total Harmonic Distortion / (20Hz to 20kHz) PHONO (MM) to REC OUT (1V) ............................. 0.02% or less CD, etc. (STEREO) to FRONT L/R SP OUT (60W, 8 ohms) .. 0.04% or less Signal to Noise Ratio / (IHF-A network) PHONO (MM) (Input shorted) to SP OUT U, C, R, T, K, L models (5mV) ............................... 86dB or more A, B, G models (5mV) ............................................ 81dB or more J model (2.5mV) ..................................................... 80dB or more CD, etc. (Input shorted, STEREO) to SP OUT 200mV .................................................................... 98dB or more 250mV .................................................................. 100dB or more


8

RX-V1500/DSP-AX1500

I General / Power Supply / U, C models ........................................................ AC 120 V, 60 Hz R model ............................. AC 110/120/220/230-240 V, 50/60 Hz T model ............................................................... AC 220 V, 50 Hz K model ............................................................... AC 220 V, 60 Hz A model ............................................................... AC 240 V, 50 Hz B, G models ........................................................ AC 230 V, 50 Hz L model ............................................ AC 220/230-240 V, 50/60 Hz J model ........................................................... AC 100V, 50/60 Hz Power Consumption / U, C models ......................................................... 500 W / 630 VA R, T, K, A, B, G, L models .................................................. 500 W J model ................................................................................ 400 W Standby Power Consumption (reference data) / () U, C, J models ..................................................................... 0.5 W R, L models (AC 240 V, 50 Hz) ........................................... 0.8 W T, K, A, B, G models ............................................................ 0.5 W Maximum Power Consumption (6ch Drive, 10% THD) R model ............................................................................. 1050 W AC Outlets / AC 2 switched outlets U, C models .......................... 100 W max. total / 0.8A max. total R, L models ........................................................ 50 W max. total T, G, J models .................................................. 100 W max. total 1 switched outlet A, B models ............................................................... 100W max. Dimensions / (W x H x D) ..................... 435 x 171 x 433.5 mm (17-1/8" x 6-3/4" x 17-1/16") Weight / RX-V1500/DSP-AX1500 ............................ 15.5 kg (34 lbs. 3 oz.) Finish / RX-V1500 .............................. Gold color (R, T, K, L) models Black color (U, C, R, A, G) models Titanium color (C, B, G, L) models DSP-AX1500 ......................... Gold color (J) model Accessories / Remote Control, Batteries (Manganese Dry), Indoor FM Antenna, AM Loop Antenna, Power Cable (U, C, T, K, A, B, G, J models), Optimizer Microphone, Speaker Terminal Wrench, Antenna Adapter PAL (B model) U .......... R .......... K .......... B .......... L ........... U.S.A. model General model Korean model British model Singapore model C ...... Canadian model T ....... Chinese model A ...... Austrarian model G ...... European model J ....... Japanese model

The variable range of the parameter (Min/Max/Step) / //Parameter name Pro Logic 10/25/1 Pro Logic II Movie/Game 10/25/1 OFF 0 (STD) 0 PL/PLx Pro Logic II Music 0/15/1 OFF/ON -3/+3/1 0/7/1 PL /PLx Neo:6 0/30/1 0/0.5/0.1 2ch -6/3/1 1/99/1 0.1/2.0/0.1 0/10/1 0/49/1 0.1/2.0/0.1 0/10/1 1.0/5.0/0.1 0/250/1 0/100/1 0/5/1 DD/dts/AAC -6/3/1 1/99/1 0.1/2.0/0.1 0/10/1 0/49/1 1/49/1 0.1/2.0/0.1 0/10/1 1.0/5.0/0.1 0/250/1 0/100/1 0/5/1 6.1/ES -6/3/1 1/99/1 0.1/2.0/0.1 0/10/1 0/49/1 1/49/1 0.1/2.0/0.1 0/10/1 1/49/1 0.1/2.0/0.1 0/10/1 1.0/5.0/0.1 0/250/1 0/100/1 0/5/1 Unit dB ms ms ms ms s ms % -

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories. DOLBYPRO LOGICEX D

DSP LEVEL (P.) INIT. DLY (P.) ROOM SIZE (P.) LIVENESS S. DELAY S. INIT. DLY S. ROOM. SIZE S. LIVENESS SB. INT.DLY SB. ROOM, SIZE SB. LIVENESS REV. TIME REV. DELAY REV. LEVEL Panorama Dimension C Width C Image DIALG. LIFT

"SILENT CINEMA" is a trademark of YAMAHA CORPORATION.SILENT THEATER

DTS and DTS-ES Digital Surround and Neo:6 are trademarks of Digital Theater Systems, Inc.DTSDTS-ESNeo:6

AAC

PL/PLx

THX and the THX logo are registered trademarks of THX Ltd. Surround EX is a jointly developed technology of THX and Dolby Laboratories, Inc. and is a trademark of Dolby Laboratories, Inc. All rights reserved. Used under authorization.

7ch Stereo Parameter CT. LEVEL SL. LEVEL SR. LEVEL SB. LEVEL RL. LEVEL RR. LEVEL

0/100/1 0/100/1 0/100/1 0/100/1 0/100/1 0/100/1

Unit % % % % % %

* Specifications are subject to change without notice due to product improvements.

150 (5-7/8")

Unit : mm (inch) : mm

21 (13/16")

435 (17-1/8")

171 (6-3/4")

18.5 (3/4")

433.5 (17-1/16")

393 (15-1/2")

22 (7/8")

DIMENSIONS /

9

10

Set Menu Table / Main category AUTO SETUP Sub-category 1 MENU No. Main Menu Initial Value

RX-V1500/DSP-AX1500

2 CHECK

CHECK CHECK CHECK Flat CHECK Auto ------

3 RESULT A B C D E F WIRING DISTANCE SIZE EQUALIZING LEVEL EXIT SET M YES NONE 7

Sub Menu WIRING DISTANCE SIZE EQUALIZING LEVEL SETUP WIRING DISTANCE SIZE EQUALIZING LEVEL L/C/R/SR/SBR/SBL/SL/SWFR/FL/FR L/C/R/SR/SBR/SBL/SL/SWFR/FL/FR L/C/R/SR/SBR/SBL/SL/SWFR/FL/FR L/R/C/SR/SBR/SBL/SL/FL/FR L/C/R/SR/SBR/SBL/SL/SWFR/FL/FR Setting Ranges CHECK, SKIP CHECK, SKIP CHECK, SKIP FRONT, Flat, Bass, Mid, High, SKIP CHECK, SKIP Auto, Step, RELOAD -----OK, NONE xx.x m, xx.x ft LARGE, SMALL, NONE -100+10 dB SET, CANCEL S, M, L YES, NONE NONE, YES 2, 3, 4, 5, 7, 8, 9 Cancelled after initial setting

MANUAL SETUP 1 BASIC MENU

2 SOUND MENU

YES SMALL SMALL SMALL SMLx2 NONE SWFR 80 Center Center Center Center Center Center Center Center 3.0 m 3.0 m 3.0 m 3.0 m 3.0 m 2.1 m 2.1 m 3.0 m 3.0 m 3.0 m 10.0 feet 10.0 feet 10.0 feet 10.0 feet 10.0 feet 7.0 feet 7.0 feet 10.0 feet 10.0 feet 10.0 feet L 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB MAX MAX OFF MAIN L/R 88 Hz 0 dB 0 dB OFF MAIN SB

ROOM SIZE SUBWOOFER PRESENCE SP Speakers SETUP (Advance to below steps when SET is selected.) CHECK TESTTONE CONFIRM A SPEAKER SET CENTER SP FRONT SP SURR. L/R SP SB SP PRESENCE SP LFE/BASS OUT SWFR CrossOver B SPEAKER FL : FR -----||----LEVEL FL : C -----||----FL : SL -----||----SL : SBL -----||----SL : SBR -----||----SL : SR -----||----FL : SWFR -----||----F : PRES -----||----C SPEAKER UNIT DISTANCE mFRONT L mFRONT R mCENTER mSURR. L mSURR. R mSB L mSB R mSWFR mPRESENCE L mPRESENCE R feetFRONT L feetFRONT R feetCENTER feetSURR. L feetSURR. R feetSB L feetSB R feetSWFR feetPRESENCE L feetPRESENCE R D GRAPHIC EQ Channel 63 Hz 160 Hz 400 Hz 1 kHz 2.5 kHz 6.3 kHz 16 kHz E LFE LEVEL SP LFE LEVEL HP LFE LEVEL F DYNAMIC RANGE SP DYNAMIC RANGE HP DYNAMIC RANGE G LOW FREQ.TEST TEST TONE OUTPUT FERQ. H HP TONE CTRL HP BASS HP TRBL I AUDIO SET AUDIO MUTE AUDIO DELAY DIALG_LIFT DUAL MONO (J) J PR/SB SELECT

YES, NO ( to SOUND_SP_LEVEL NONE, SMALL, LARGE SMALL, LARGE NONE, SMALL, LARGE NONE, SMLx1, SMLx2, LRGx1, LRGx2 NONE/YES SWFR, MAIN, BOTH 40, 60, 80, 90, 100, 110, 120, 160, 200 Hz Center (20 step) Center (20 step) Center (20 step) Center (20 step) Center (20 step) Center (20 step) Center (20 step) Center (20 step) meters (m) / feet (ft) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 0.3 to 24.0 m (0.1 m step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) 1.0 to 80 feet (0.5 feet step) L, R, CT, SR L/R, SB L/R, PRES L/R 6 dB (0.5 dB step) 6 dB (0.5 dB step) 6 dB (0.5 dB step) 6 dB (0.5 dB step) 6 dB (0.5 dB step) 6 dB (0.5 dB step) 6 dB (0.5 dB step) -20 dB to 0 dB (1 dB step) -20 dB to 0 dB (1 dB step) MIN, STD, MAX MIN, STD, MAX OFF, ON MAIN L/R, L, C, R, SR, SBL, SBR, SL, SWFR 35 Hz 88 Hz WIDE -6 dB to + 6 dB (0.5 dB step) -6 dB to + 6 dB (0.5 dB step) , -20 dB 0 240 ms OFF/ON MAIN, SUB, ALL SB, PR

3 INPUT MENU

A DVD DTV MD/TAPE CD-R CD DVD DTV CBL/SAT CD DVD DVR/VCR2 AUTO 6 ch, 8 ch

4 OPTION MENU

I/O ASSIGNMENT [A] CV INPUT 1 [B] CV INPUT 2 (1) OPTICAL OUT 1 (2) OPTICAL OUT 2 (3) OPTICAL IN 1 (4) OPTICAL IN 2 (5) OPTICAL IN 3 (6) OPTICAL IN 4 (7) COAXIAL IN 1 (8) COAXIAL IN 2 (9) COAXIAL IN 3 B INPUT MODE C INPUT RENAME DVD_ _ DVD _ _ _ D EXT INPUT SET 1 6ch/8ch 2. 8CH INPUT FRONT 3 CENTER to 4 SWFR to 5 SURR L/R to A DISPLAY SET DIMMER OSD SHIFT GRAY BACK V CONV. CMPNT_OSD B MEMORY GUARD C PARAM.INI PARAM INIT 1 PARAM INIT 2 PARAM INIT 3 D SP IMP.SET E ZONE SET SP B SET F ZONE2 SET (UCA) ZONE2 OUT ZONE2 AMP G ZONE3 SET (UCA) ZONE3 OUT (OnlyV2400) 6ch DVD CT SW SURR L/R 0 0 AUTO ON ON OFF Parameters are initialized when keys of asterisk marked numbers are pressed (1 to 10 for V1400) 8 ohms FRONT VAR. OFF VAR. CT, FRONT SW, FRONT SURR L/R, FRONT -4 to 0 (1 step) 0 5 (1 step) AUTO, OFF OFF, ON OFF, ON OFF, ON 8 ohms, 6 ohms FRONT, ZONE B VAR., FIX OFF, ON VAR., FIX

RX-V1500/DSP-AX1500


11

RX-V1500/DSP-AX1500

I INTERNAL VIEW1 2 3 4 5 6 7 8 9 0A B C D 1 POWER (5) P.C.B. 2 POWER (4) P.C.B. (R, L models only) 3 MAIN (1) P.C.B. 4 POWER (7) P.C.B. (U, C, A, B, G models only) 5 MAIN (5) P.C.B. 6 POWER (6) P.C.B. 7 MAIN (3) P.C.B. 8 VIDEO (4) P.C.B. 9 TUNER 0 CONVERSION P.C.B. A VIDEO (8) P.C.B. B VIDEO (7) P.C.B. C VIDEO (3) P.C.B. D VIDEO (5) P.C.B. E VIDEO (6) P.C.B. F VIDEO (2) P.C.B. G VIDEO (1) P.C.B. H MAIN (2) P.C.B. I DSP P.C.B. J FUNCTION P.C.B. K MAIN (4) P.C.B. L POWER (1) P.C.B. M POWER (3) P.C.B. N OPERATION (3) P.C.B. O POWER (2) P.C.B. P OPERATION (1) P.C.B. Q OPERATION (2) P.C.B

E F G H I J

O

N P

ML K Q


12

RX-V1500/DSP-AX1500

I DISASSEMBLY PROCEDURES / * The description below uses RX-V1500 (G model) as a representative model. (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. 1. Removal of Top Cover a. Remove 2 screws (1), 4 screws (2) and 5 screws (3). (Fig. 1) b. Slide the Top Cover rearward to remove it. (Fig. 1) RX-V1500 (G model) AC

1. a. 245 Fig. 1 b. Fig. 1

2. Removal of Front Panel Remove 7 screws (4) and then remove the Front Panel forward. (Fig. 1)

2. 7 Fig. 13 1 Top Cover

2

3

4

2

4 Front Panel

Fig. 1 3. Removal of Sub Chassis a. Remove 4 push rivets (5) and then remove the Side Plates. (Fig. 2) b. Remove 2 screws (6) and 2 screws (7). (Fig. 2) c. Remove CB25, CB509, CB512, CB905 ~ CB908. (Fig. 3) d. Remove the Sub Chassis forward. (Fig. 2) 4. Removal of DSP P.C.B. a. Remove 2 screws (8) and then remove the Supports. (Fig. 2) b. Remove 5 screws (9) and then remove the Bracket. (Fig. 2) c. Remove 3 screws (0). (Fig. 2) d. Remove 8 screws (A). (Fig. 4) e. Remove CB501, CB503 ~ CB505. (Fig. 3) f. Remove the DSP P.C.B. upward. (Fig. 2)

3. a. 4 Fig. 2 b. 22 Fig. 2 c. CB25CB509CB512CB905CB908 Fig. 3 d. Fig. 2

4. DSP P.C.B.a. 2 Fig. 2 b. 5 Fig. 2 c. 3 Fig. 2 d. 8 Fig. 4 e. CB501CB503CB505 Fig. 3 f. DSP P.C.B. Fig. 2RX-V1500/ DSP-AX1500

13

RX-V1500/DSP-AX1500

5. a. b. c.

Removal of VIDEO (2) P.C.B. Remove 1 screw (B). (Fig. 2) Remove CB554, CB555 and CB558. (Fig. 3) Remove the VIDEO (2) P.C.B. which is connected directly to the lower P.C.B. with connectors. (Fig. 2)Side Plate L L

5. VIDEO 2 P.C.B.a. 1 Fig. 2 b. CB554CB555CB558 Fig. 3 c. VIDEO2P.C.B.P.C.B. Fig. 2B VIDEO (2) P.C.B.

5 6 DSP P.C.B.

5

8 0 7 5 Sub Chassis 9 9

Support 9 9

9 Bracket

7 5 Side Plate R R

6

Fig. 2 CB555 CB558 CB554

CB504 CB505 CB501 CB503

CB509 CB512

CB25

CB908 CB907 CB906 Fig. 3

CB905

A

C


14

C

Fig. 4

RX-V1500/DSP-AX1500

6. Removal of VIDEO (1) ~ (3), (5) ~ (8), FUNCTION, CONVERSION P.C.B.s and Tuner a. Remove 26 screws (C). (Fig. 4) b. Remove VIDEO (1) ~ (3), (5) ~ (8), FUNCTION, CONVERSION P.C.B.s and Tuner. (Fig. 5)

6. VIDEO 1 3 5 8 FUNCTION CONVERSION P.C.B.a. 26 Fig. 4 b. V I D E O 1 3 5 8 F U N C T I O N CONVERSION P.C.B. Fig. 5 P.C.B. P.C.B. Fig. 5 P.C.B. P.C.B. GND

When checking the P.C.B.: Put the Rubber Sheet and a Cloth over the equipment. Then place the P.C.B. upside down on the Cloth and check it. (Fig. 5) Reconnect all cables (connectors) that have been disconnected. When connecting the flat cable, use care for the polarity. The P.C.B. removed from the rear panel does not work because its grounding is loose. Be sure to connect the ground of each P.C.B. to the chassis or GND with a jumper wire or the like.

VIDEO (6) P.C.B. FUNCTION P.C.B. Rubber Sheet and Cloth VIDEO (5) P.C.B. VIDEO (3) P.C.B. VIDEO (8) P.C.B. VIDEO (7) P.C.B. Tuner

CONVERSION P.C.B. VIDEO (2) P.C.B. VIDEO (1) P.C.B. DSP P.C.B.

Fig. 5


15

RX-V1500/DSP-AX1500

7. Removal of Fan a. Remove 4 push rivets (D) and then remove the Cover. (Fig. 6) b. Remove 2 screws (E) and 2 screws (F). (Fig. 6) c. Remove the Fan together with the frame by lifting them up. (Fig. 6) 8. Removal of Amp Unit a. Remove 2 push rivets (G) and then remove the Duct. (Fig. 6) b. Remove 4 screws (H) and 4 screws (I). (Fig. 6) c. Remove the Amp Unit. (Fig. 6) When checking the Amp Unit: Put the Amp Unit together with the heat sink upright on the art base and check them. Reconnect all cables (connectors) that have been disconnected. When connecting the flat cable, use care for the polarity.D

7. a. 4 Fig. 6 b. 22 Fig. 6 c. Fig. 6

8. a. 2 Fig. 6 b. 44 Fig. 6 f. Fig. 6 Fig. 7

D E Duct Fan

Cover F H I I G

H

Amp Unit Amp Unit

Fig. 6


Cloth

Fig. 7 16

RX-V1500/DSP-AX1500

I UPDATING FIRMWARE / After replacing the IC512 on the FUNCTION P.C.B. with the service part (X4678A00), update the firmware according to the following procedure. FUNCTION P.C.B.IC512 X4678A00

Equipment required PC with RS-232C serial port (OS: Windows98/2000/ Me/XP) Firmware loading program (YAVBoot_V518.exe) Firmware (V1500_xxx.mot) RS-232C cross cable "D-Sub 9-pin Female". Pin No.2 RxD Pin No.2 RxD Pin No.3 TxD Pin No.3 TxD Pin No.5 GND Pin No.5 GND Pin No.7 RTS Pin No.7 RTS Pin No.8 CTS Pin No.8 CTS RS-232C Conversion Adapter (Part #: AAX24910)

RS-232CPCOS: Windows 98/ 2000/Me/XP YAVBoot_V518.exe V1500_xxx.mot RS-232C D-sub pin Pin No.2 RxD Pin No.2 RxD Pin No.3 TxD Pin No.3 TxD Pin No.5 GND Pin No.5 GND Pin No.7 RTS Pin No.7 RTS Pin No.8 CTS Pin No.8 CTS RS-232C AAX24910

PreparationsDownload the firmware loading program and firmware from the specified download sources to the same directory of the PC for updating the firmware.

PC

Firmware updating procedure1. With the power turned off, connect the RS-232C cross cable and RS-232C conversion adapter between the PC and the port for writing of the unit as shown below.

1. RS-232CRS232CPC


17

RX-V1500/DSP-AX1500

2. After executing the firmware loading program, select the program type and port settings as follows:

2. Program Type

Program Type Select Program Type: V1500 COM > SETTING Menu Port Setting Dialog Port: Select proper port # Bits per second: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: Hardware

3. Turn on the power to the unit. 4. To connect the line, click the CONNECT button or the COM menu, then click the CONNECT.

3. ON 4. CONNECTCOM CONNECT

COM > CONNECT Menu After connecting, the "Connected" message is displayed in the status bar. 5. Click the File Change button and then select the file to be loaded. To start the loading, click the Program Macro button. Never disconnect the power cable of the unit while loading the firmware, or the flash ROM data may be destroyed. 6. When the firmware loading is finished, the checksum information will be displayed on the information box. 7. To disconnect the line, click the BREAK button or click the COM menu, then click the BREAK. Connected 5. File Change Program Macro ROM 6. 7. BREAK COM MenuBREAK

COM > BREAK Menu

For more information, access to the FIRMWARE UPDATE PROCEDURES on the WEB SITE.

WEB SITE FIRMWARE UPDATE PROCEDURES


18

RX-V1500/DSP-AX1500

I SELF DIAGNOSIS FUNCTION (DIAG) There are 18 DIAG menu items, each of which has submenu items. Listed in the table below are menu items and sub-menu items. No DIAG menu 1 2 3 4 DA601-YSS930 BYPASS RAM THROUGH PRO LOGIC / NEO6 sub-menu 1. YSS 0dB 2. YSS FULL BIT 1. ANALOG BYPASS 2. DSP BYPASS 1. RAM 0dB 2. FRONT ATT 1. PRO LOGIC I 2. PRO LOGIC II 3. NEO: 6 1. FRONT: SMALL 0dB 2. CENTER: NONE 3. LFE/BASS: FRONT 4. PRESS MIX: 5ch 5. SURROUND B: MUTE 6. SURROUND LR: MUTE 7. SURROUND LR: NONE 6 EXTERNAL INPUT 1. 6CH_INPUT_6OHMS 2. 6CH_INPUT_8OHMS 3. 8CH_INPUT_6OHMS 4. 8CH_INPUT_8OHMS MIC CHECK 1. VFD CHECK (Initial display / ) 2. VFD DISP OFF (All segments OFF / ) 3. VFD DISP ALL (All segments ON 100% / 100%) 4. VFD DIMMER (All segments ON 50% / 50%) 9 MANUAL TEST 5. CHECKED PATTERN (ON in lattice / ) 1. TEST ALL 2. TEST FRONT L 3. TEST CENTER 4. TEST FRONT R 5. TEST SURROUND R 6. TEST SURROUND BACK R 7. TEST SURROUND BACK L 8. TEST SURROUND L 9. TEST PRESENCE L 10. TEST PRESENCE R 11. TEST LFE 10 RS-232C 11 FACTORY PRESET 1. TX DATA 2. HARD FLOW 1. PRESET INHIBIT (memory initialization inhibited / ) 2. PRESET RESERVED (memory initialized / )RX-V1500/ DSP-AX1500

1 8

5

SPEAKER SET

7 8

MIC CHECK EFFECT OFF/ DISPLAY CHECK

19

RX-V1500/DSP-AX1500

No DIAG menu 12 AD DATA CHECK /FAN TEST

sub-menu 1. DC/PS (protection) 2. THM/FAN OUT 3. REC-OUT 4. IMP SW/POWER LIMIT 5. K0/K1 (panel key) 6. FAN DRIVE TEST: HIGH 7. FAN DRIVE TEST: MID

13 V CONV STATUS 14 IF STATUS

8. FAN DRIVE TEST: LOW 1. LOW BYTE DATA 2. HIGH BYTE DATA (Not applied to this models. / ) 1. IS 1 (5 Byte) 2. IS 2 3. CS 1 4. CS 2 5. CS 3 6. CS 4 7. CS 5 8. BS1 9. BS2 10. BS3 11. BS4 12. BS5 13. TI1 14. TI2 15. MTT (3 Byte) (5 Byte) (5 Byte) (5 Byte) (5 Byte) (4 Byte) (5 Byte) (5 Byte) (5 Byte) (5 Byte) (5 Byte) (5 Byte) (1 Byte) (5 Byte)

15 DSP RAM CHECK 16 PROTECTION SET 17 SOFT SW

1. YSS930 BUS CHECK 2. SECOND DECODER BUS CHECK Not applied to this models. / 1. SW MODE 2. MODEL SETTING 3. TUNER DESTINATION 4. TUNER EXIST 5. RDS EXIST 6. ZONE 2 EXIST 7. VIDEO FORMAT

18 ROM VERSION/CHECK SUM/ PORT

1. VERSION 2. OPE/DSP VERSION 3. SUM ALL/PROGRAM 4. SUM 232C BOOT/MAKER BOOT 5. PORT 6. AAC PORT


20

RX-V1500/DSP-AX1500

Starting DIAGPress the STANDBY/ON key while simultaneously pressing those two keys of the main unit as indicated in the figure below.

STANDBY/ ON

Keys of main unit /

Turn on the power while pressing these keys.

Starting DIAG in the protection cancel modeIf the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described below, and it will be possible to enter the DIAG mode. (The protection functions other than the excess current detect function will be disabled.) Press the STANDBY/ON key while simultaneously pressing those two keys indicated in the figure above. At this time, keep pressing those two keys for 3 seconds or longer. In this mode, the SLEEP segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the protection functions disabled.

STANDBY/ON 3 FL SLEEP

CAUTION!Using this product with the protection function disabled may cause damage to itself. Use special care for this point when using this mode.

Canceling DIAG[1] Before canceling DIAG, execute setting for PRESET of DIAG menu No.11 (Memory initialization inhibited or Memory initialized). * In order to keep the user memory stored, be sure to select PRESET INHIBIT (Memory initialization inhibited). Any protection history will remain in memory. [2] Turn off the power by pressing the STANDBY/ON key of the main unit or the STANDBY key of the remote controller.

No.11 FACTORY PRESET/ PRESET INHIBIT STANDBY/ON STANDBY


21

RX-V1500/DSP-AX1500

Display provided when DIAG startedWhen the monitor is connected, DIAGNOSTIC MENU appears on its screen as shown in the figure. (It remains on display until DIAG is cancelled.)

DIAGNOSTIC MENU1.DSP THR 2.BYPASS 3.RAM THR 4.PRO LOGIC 5.SP SET 6.EXT_INPUT 7.MIC CHECK 8.VFD CHECK 9.MAN LTEST The FL display of the main unit displays the protection function history data and the version (1 alphabet) and the DIAG menu [sub-menu (YSS 0dB) of DIAG menu No.1 DSP THROUGH] a few seconds later. 10.RS232C 11.PRESET 12.AD/FAN 13.VC STATUS 14.IF STATUS 15.DSP RAM 16.PRT SET 17.SOFT SW 18.VER/SUM/P FL 1 No.1 DSP THROUGHYSS 0dB

When there is no history of protection function:Opening message / When there is no history of protection function

:DIAG menu display /

Version (1 alphabet) 1 After a few seconds

When there is a history of protection function:

:

When there is a history of protection function due to excess current Version (1 alphabet) 1

Cause: An excessive current flowed through the power amplifier. Turning on the power without correcting the abnormality will cause the protection function to work immediately and the power supply will instantly be shut off. Note) Applying the power to a unit without correcting the abnormality can be dangerous and cause additional circuit damage. The output transistors in each amplifier channel should be checked for damage before applying any power. Amplifier current should be monitored by measuring across the emitter resistors for each channel.


22

RX-V1500/DSP-AX1500

When there is a history of protection function due to abnormal voltage in the power supply section

Version (1 alphabet) 1

Voltage display in % %

Cause: The voltage in the power supply section is abnormal. Supplementary information: The abnormal voltage is displayed in % based on 5V as 100%. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply will be shut off.

5V100%% 1

When there is a history of protection function due to abnormal DC output DC


Cause: DC output of the power amplifier is abnormal. Supplementary information: The abnormal voltage is displayed in % based on 5V as 100%. Turning on the power without correcting the abnormality will cause the protection function to work 3 seconds later and the power supply will be shut off.

DC 5V100%% 3

When there is a history of protection function due to excessive heat sink temperature


Voltage display in % %

Cause: The temperature of the heat sink is excessive. Supplementary information: The abnormal voltage is displayed in % based on 5V as 500%. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply will be shut off. * Additional causes of protection can be due to loose connections, associated components, CPU, etc. * For the protection voltage value, refer to DIAG menu No.12 described later.

5V500%% 1 CPU No.12RX-V1500/ DSP-AX1500

23

RX-V1500/DSP-AX1500

History of protection functionWhen the protection function has worked, its history is stored in memory with a backup. Even if no abnormality is noted while servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has been stored. The history of the protection function is cleared when DIAG is cancelled by selecting PRESET RESERVED (Memory initialized) of DIAG menu No. 11 or when the backup data is erased.

No.11 PRESET RESERVED

Display during menu operationDuring the DIAG operation, the menu list described in the section of the startup screen appears on the superimposed screen and the function at work is indicated on the FL indicator. The contents displayed during the function operation are described in the later section on details of functions.

FL

Operation procedure of DIAG menu and SUB-MENUThere are 18 MENU items, each of which has some SUBMENU items.

No.118

PROGRAM

DIAG menu selectionSelect the menu using PROGRAM knob.

SUB-MENU selectionSelect the sub-menu using keys of PRESET/TUNING. (Forward) and (Reverse) PRESET/TUNING ,

SUB-MENU selection

DIAG menu selection

Reverse

Forward

Reverse

Forward


24

RX-V1500/DSP-AX1500

Functions in DIAG modeIn addition to the DIAG menu items, functions as listed below are available. Input selection, Multi channel input Center/Surround/Surround Back/Sub-woofer level adjustment Muting Speaker relay A/B Power on/off Master volume * Functions related to the tuner and the set menu are not available. * It is possible to confirm Menu No.14 IF STATUS while keeping the signal process (operation status) of each DIAG menu by using the input mode key of the main unit.

A/B / INPUT MODE No.14 IF STATUS

Initial settings used to start DIAGThe following initial settings are used when starting DIAG. When DIAG is canceled, these settings are restored to those before starting DIAG. Master volume: -20dB Input: DVD (MULTI CHANNEL INPUT OFF) Effect level: 0dB Audio mute: OFF Speaker relay A/B: ON Speaker setting: LARGE / BASS OUT = BOTH DIAG menu: DA601-YSS930 (1. YSS 0dB)

: -20dB : DVD INPUT : 0dB : A/B: : LARGE / BASS OUT=BOTH : DA601-YSS930 1. YSS 0dB


25

RX-V1500/DSP-AX1500

Details of DIAG menuWith full-bit output specified in some modes, it is possible to execute 0dBFS output without head margin in each channel.

0dBFS

1. DA601-YSS930This function is for YSS930 only. Main DSP of YSS930 is selected for FRONT output. Using the sub-menu, it is possible to select 0dB output level or full-bit output. YSS 0dB The signal is output including the head margin.

1. DA601-YSS930YSS930FRONTYSS930 Main DSP 0dB YSS 0dB

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz Input level Both ch, -20 dBm Volume +6.5 dB PRE OUTPUT CENTER SURROUND SURROUND BACK SUBWOOFER -16.3 dBm -16.8 dBm -17.0 dBm -17.0 dBm

FRONT -16.3 dBm

YSS FULL BIT The signal is output in digital full bit without including the head margin. The SWFR signal is output but not in digital full bit.

YSS FULL BIT SWFR

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz Input level Both ch, -20 dBm Volume +6.5 dB PRE OUTPUT SURROUND SURROUND BACK SUBWOOFER -16.8 dBm -17.0 dBm -17.0 dBm

FRONT -16.3 dBm

CENTER -16.3 dBm

DA601-YSS930 (ANALOG)

4Mbit DRAMDIR L/R


Analog

A/D AK5380

AD L/R

L/R

L/R

L/R

L/R

SL/SR C/LFE SBL/ SBR

SL/SR SBL/ SBR CL/CR SWL/ SWR

SL/SR SBL/SBR or PL/PR

DigitalDIR DECODE DSP

CL/CR SWL/SWR

POST PROCESSING DSP

PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA601

YSS930 D0

YSS930 D1

26

(Shaded items not used in this example)

RX-V1500/DSP-AX1500

2. BYPASSANALOG BYPASS

2. BYPASSANALOG BYPASS

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz PRE OUTPUT Input level Both ch, -20 dBm Volume +6.5 dB FRONT -15.7 dBm CENTER - SURROUND SURROUND BACK SUBWOOFER - - -

DSP BYPASS

DSP BYPASS

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz PRE OUTPUT Input level Both ch, -20 dBm Volume +6.5 dB FRONT - CENTER - SURROUND SURROUND BACK SUBWOOFER - - -

ANALOG BYPASS, DSP BYPASS (ANALOG)

4Mbit DRAMDIR L/R

Analog

A/D AK5380

AD L/R

L/R

L/R

L/R

L/R





CL/CR SWL/SWR

POST PROCESSING DSP

PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA601

YSS930 D0

YSS930 D1

(Shaded items not used in this example) DSP BYPASS (DIGITAL)4Mbit DRAMDIR L/R

Analog

A/D AK5380

AD L/R

L/R

L/R

L/R

L/R






CL/CR SWL/SWR

POST PROCESSING DSP

PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA601

YSS930 D0

YSS930 D1


27

RX-V1500/DSP-AX1500

3. RAM THROUGHUsing the sub-menu, it is possible to select the full-bit output at 0dB output level.

3. RAM THROUGH0dB

RAM 0dB

RAM 0dB

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz PRE OUTPUT Input level Both ch, -20 dBm Volume +6.5 dB FRONT -16.3 dBm CENTER -16.2 dBm SURROUND SURROUND BACK SUBWOOFER -17.0 dBm -17.0 dBm -17.0 dBm

FRONT ATT MAIN -9dB

FRONT ATT MAIN -9dB

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz PRE OUTPUT Input level Both ch, -20 dBm Volume +6.5 dB FRONT -25.0 dBm CENTER -16.2 dBm SURROUND SURROUND BACK SUBWOOFER -17.0 dBm -17.0 dBm -17.0 dBm

RAM THROUGH (ANALOG)4Mbit DRAMDIR L/R

Analog

A/D AK5380

AD L/R

L/R

L/R

L/R

L/R

SL/SR C/LFE




SBL/ SBR

CL/CR SWL/SWR

POST PROCESSING DSP

PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA601

YSS930 D0

YSS930 D1



28

RX-V1500/DSP-AX1500

4. PRO LOGIC / NEO6PRO LOGIC I Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz Input level Each ch, -20 dBm Both ch, -20 dBm Volume +6.5 dB +6.5 dB FRONT -16.3 dBm - CENTER - -13.4 dBm

4. PRO LOGIC / NEO6PRO LOGIC I

PRE OUTPUT SURROUND SURROUND BACK SUBWOOFER - - - - - -

PRO LOGIC II Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz Input level Each ch, -20 dBm Both ch, -20 dBm Volume +6.5 dB +6.5 dB FRONT -16.3 dBm - CENTER - -13.4 dBm

PRO LOGIC II

PRE OUTPUT SURROUND SURROUND BACK SUBWOOFER - - - - - -

Neo:6

Neo:6

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz Input level Each ch, -20 dBm Both ch, -20 dBm Volume +6.5 dB +6.5 dB PRE OUTPUT SURROUND SURROUND BACK SUBWOOFER - - - - - -

FRONT -16.3 dBm -

CENTER - -13.4 dBm

PRO LOGIC/NEO:6 (ANALOG)4Mbit DRAMDIR L/R

Analog

A/D AK5380

AD L/R

L/R

L/R

L/R

L/R

SL/SR C/LFE


SL/SR


SBL/SBR or PL/PR


SBL/ SBR

CL/CR SWL/SWR

POST PROCESSING DSP

PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA601

YSS930 D0

YSS930 D1

(Shaded items not used in this example) 29

RX-V1500/DSP-AX1500

5. SPEAKERS SETThe input signal is automatically identified in the order of dts DOLBY DIGITAL AAC PCM Analog. There are seven sub-menu items as follows. The signals output from the DSP block are the same as 1. DA601-YSS930: YSS 0dB. FRONT: SMALL 0dB

5. SPEAKERS SETDTS DOLBY DIGITAL AAC PCM 7 DSPNo.1 DA601-YSS930YSS 0dB LFE: BASS: FRONT

CENTER: NONE

PRESS MIX: 5ch

SURROUND BACK: MUTE

SURROUND L/R: MUTE

SURROUND L/R: NONE

The analog switch settings for each sub-menu are as shown in the table below. Sub-menu 1 2 3 4 5 6 7 FRONT: SMALL 0dB CENTER: NONE LFE/BASS: FRONT PRESS MIX: 5CH SURROUND BACK: MUTE SURROUND: MUTE SURROUND: NONE

CENTER SP SURROUND SP FRONT SP LFE/BASS LARGE NONE SMALL LARGE LARGE LARGE LARGE LARGE LARGE SMALL LARGE LARGE LARGE NONE SMALL LARGE LARGE LARGE LARGE LARGE LARGE SWFR SWFR MAIN SWFR SWFR SWFR SWFR

LARGE:

SMALL:

NONE:

This mode is used with a speaker with high bass reproduction performance (a large unit). Full bandwidth signals are output. This mode is used with a speaker with low bass reproduction performance (a small unit). The signals of 90Hz or less are mixed into the channel specified by LFE/BASS. This mode is used with no center speaker. The center content is reduced by 3dB and distributed to FRONT L/R.

LARGE SMALL 90Hz LFE/BASS NONE -3dBFRONT L/R

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHzRX-V1500/ DSP-AX1500

PRE OUTPUT Sub-menu 1 2 3 4 5 6 30 7 FRONT: SMALL 0dB CENTER: NONE LFE/BASS: FRONT PRESS MIX: 5CH FRONT 1 kHz Both ch, -20 dBm +6.5 dB -16.3 dBm 1 kHz Both ch, -20 dBm +6.5 dB -20.0 dBm 1 kHz Both ch, -20 dBm +6.5 dB -16.2 dBm 50 Hz Both ch, -20 dBm +6.5 dB -5.7 dBm 1 kHz Both ch, -20 dBm +6.5 dB -16.3 dBm Input level Volume CENTER SURROUND SURROUND BACK SUBWOOFER -16.3 dBm -17.0 dBm -17.0 dBm -17.0 dBm - -17.0 dBm -17.0 dBm -17.0 dBm -16.2 dBm -16.7 dBm -16.7 dBm - -26.0 dBm -26.0 dBm -26.0 dBm - -16.3 dBm -17.0 dBm -17.0 dBm -17.0 dBm

SURROUND BACK: MUTE 1 kHz Both ch, -20 dBm +6.5 dB -16.3 dBm -16.3 dBm -17.0 dBm -17.0 dBm -17.0 dBm SURROUND: MUTE 1 kHz Both ch, -20 dBm +6.5 dB -16.3 dBm -16.3 dBm - -17.0 dBm -17.0 dBm SURROUND: NONE 1 kHz Both ch, -20 dBm +6.5 dB -17.3 dBm -16.3 dBm - -17.0 dBm -17.0 dBm

RX-V1500/DSP-AX1500

6. EXTERNAL INPUTIt is possible to select the 6ch/8ch input and 6_/8_ by using the SUB menu. 6CH_INPUT_6OHMS

6. EXTERNAL INPUT6ch/8ch6/8 6CH_INPUT_6OHMS

6CH_INPUT_8OHMS

6CH_INPUT_8OHMS

8CH_INPUT_6OHMS

8CH_INPUT_6OHMS

8CH_INPUT_8OHMS

8CH_INPUT_8OHMS

Reference data INPUT: DVD ANALOG SUBWOOFER: 50Hz, Others: 1kHz Sub-menu 1 2 3 4 6CH_INPUT_6ohms 6CH_INPUT_8ohms 8CH_INPUT_6ohms 8CH_INPUT_8ohms Input level Volume FRONT PRE OUTPUT CENTER SURROUND SURROUND BACK SUBWOOFER - - - - - - - -

Both ch, -20 dBm +6.5 dB -16.0 dBm -15.8 dBm -16.0 dBm Both ch, -20 dBm +6.5 dB -16.0 dBm -15.8 dBm -16.0 dBm Both ch, -20 dBm +6.5 dB -15.7 dBm -15.8 dBm -16.0 dBm Both ch, -20 dBm +6.5 dB -15.7 dBm -15.8 dBm -16.0 dBm

7. MIC CHECKThe signals inputted through the microphone are output via A/D - D/A.

7. MIC CHECKA/DD/A


31

RX-V1500/DSP-AX1500

8. EFFECT OFF / DISPLAY CHECKThis program is used to check the FL display section. The display condition varies as shown below according to the sub-menu operation. The signals are processed using EFFECT OFF (The L/R signal is output using ANALOG MAIN BYPASS.) The video signal internal/external synchronization switching is controlled by the microprocessor. When the initial message is displayed and all the FL segments light up, it is switched to the internal synchronization but other than that it is forced to the external synchronization setting. Also, except for the initial display, 128 pictographs for checking the OSD driver are used for the video signal output display.

8. EFFECT OFF / DISPLAY CHECKFL EFFECT OFF ANALOG MAIN BYPASS L/R / FL OSD 128

Initial display

All segments OFF

All segments ON (dimmer 100%) 100%

Lighting in lattice

Lighting of segments in lattice

All segments ON (dimmer 50%) 50%

Short Normal

Segment conditions of the FL driver and the FL tube are checked by turning ON and OFF all segments. Next, the operation of the FL driver is checked by using the dimmer control. Then a short between segments next to each other is checked by turning ON and OFF all segments alternately (in lattice). (In the above example, the segments in the second row from the top are shorted.)

FL FL FL /


32

RX-V1500/DSP-AX1500

9. MANUAL TESTThe noise generator with a built-in DSP outputs the test noise through the channels specified by the sub-menu. The noise frequency for LFE is 35 to 250 Hz. Other than that, the center frequency is 800Hz. TEST ALL

9. MANUAL TESTDSP LFE35250Hz 800Hz TEST CENTER

TEST FRONT L

Noise is output from all channels.

Noise is output from the FRONT L channel. FRONT L

Noise is output from the CENTER channel. CENTER TEST SURROUND BACK R

TEST FRONT R

TEST SURROUND R

Noise is output from the FRONT R channel. FRONT R

Noise is output from the SURROUND R channel. SURROUND R TEST SURROUND L

Noise is output from the SURROUND BACK R channel. SURROUND BACK R TEST PRESENCE L

TEST SURROUND BACK L

Noise is output from the SURROUND BACK L channel. SURROUND BACK L TEST PRESENCE L

Noise is output from the PRESENCE L Noise is output from the SURROUND L channel. channel. SURROUND L PRESENCE L TEST LFE

Noise is output from the PRESENCE R channel. PRESENCE R

Noise is output from the SUB WOOFER channel. SUB WOOFER


33

RX-V1500/DSP-AX1500

10. RS-232CThis menu is used to check transmission of the data and the flow port of the hardware. With the power turned off, short between pins No.2 (RxD) and No.3 (TxD), and between pins No.7 (RTS) and No.8 (CTS) of the RS-232C terminal. (Be sure to turn off the power when shorting the pins.) Start DIAG and select the menu. There are two sub-menu items.RxD TxD1 6 2

10. RS-232C R S - 2 3 2 C2 RxD 3 TxD 7 RTS 8 CTS 2

7 3 8 4 9

5

RTS CTS

TxD/RxD DATA The sub-menu is used to check transmission of the test data. OK appears when the data is transmitted properly and NG when it is not. In this mode, NULL command transmission is continued after the test command is transmitted.

TxRx Data OK NG 200ms NULL

HARD FLOW This sub-menu is used to check operation of the flow port of the hardware. OK appears when the check result is satisfactory and NG when it is not.

Hard Flow OK NG


34

RX-V1500/DSP-AX1500

11. FACTORY PRESETThis menu is used to reserve and inhibit initialization of the back-up RAM. The signals are processed using EFFECT OFF. (The L/R signal is output using ANALOG MAIN BYPASS.)

11. FACTORY PRESETRAM / EFFECT OFF ANALOG MAIN BYPASSL/R

PRESET INHIBIT (Initialization inhibited) / PRESET INHIBIT RAM initialization is not executed. Select this sub-menu to protect the values set by the user. RAM PRESET RESERVED (Initialization reserved) / PRESET RESERVED Initialization of the back-up RAM is reserved. (Actually, initialization is executed the next time that the power is turned on.) Select this sub-menu to reset to the original factory settings or to reset the RAM. Any protection history will be cleared. RAM RAM CAUTION: Before setting to the PRESET RESERVED, write down the existing preset memory content of the Tuner in a table as shown below. (This is because setting to the PRESET RESERVED will cause the user memory content to be erased.)Preset group A B C D E P1 P2 P3

PRESET RESERVED

P4

P5

P6

P7

P8

PRESET STATIONS / STATION PAGE NO. 1 2 3 4 5 6 7 8 FM FACTORY PRESET DATA (MHz) U, C A, B, G, L, R, T, K J 87.5 87.50 76.0 90.1 95.1 98.1 107.9 88.1 106.1 107.9 90.10 95.10 98.10 108.00 88.10 106.10 108.00 83.0 84.0 86.0 90.0 78.0 88.0 82.1 STATION PAGE NO. 1 2 3 4 5 6 7 8 AM FACTORY PRESET DATA (kHz) U, C, R, T, K A, B, G, L J 630 630 630 1080 1440 530 1710 900 1350 1400 1080 1440 531 1611 900 1350 1404 1080 1440 531 1611 900 1350 1404

A/C/E

B/D


35

RX-V1500/DSP-AX1500

12. AD DATA CHECK / FAN TESTThis menu is used to display the A/D conversion value of the main CPU which detects panel keys of the main unit and protection functions in % using the sub-menu. During signal processing, the condition before execution is maintained. When K0/K1 menu is selected, keys become nonoperable due to detection of the values of all keys. However, it is possible to advance to the next submenu by turning the VOLUME of the main unit. When using this function, note that turning the VOLUME more than 1 click would cause the volume value to change. * The figures in the diagram are given as reference only. DC/PS (protection detection) DC: DC detect protection value (Normal value: 1 to 13) PS: Power supply voltage protection value (Normal value: 19 to 29) * If DC or PS is out of the normal value range, the protection function works to turn off the power. (Reference voltage: 5V=100%)

12. AD DATA CHECK / FAN TEST CPUA/D% K0/K1 VOLUME 1

DC/PS DCDC 113 PS 1929 DCPS 5V=100%

THM/FAN OUT (temperature detection/fan drive level) THM: 500% display of the voltage based on the temperature detected value. Reference voltage: 5V=500% (Normal value: 10 to 139) Fan: Current fan drive level on the left and the past fan drive history on the right.

THM/FAN OUT / THM: 500 5V : 10139 Fan:

Display fan drive level

H HIGH

M MID

L LOW

REC-OUT (Select position) Not applied to this model.

REC-OUT


36

RX-V1500/DSP-AX1500

IMP SW/POWER LIMIT (Impedance/power limiter detection) IMP: Not applied to this model. PL: Power limiter detection value The voltage value of pin No. 135 of IC520 is displayed, using 5V/256 as standard. Based on the input voltage value of pin No.135 of IC520, the output of pins No.6 (LC1) and No.7 (LC2) of IC505 is controlled. Speaker impedance setting During normal operation When limiter is operating 7CH STEREO LC1=L LC1=H or LC2=H LC2=H 6 ohms EXT8CH_INPUT Other than those LC1=L LC1=H on the above LC2=H LC2=L 7CH STEREO LC1=L LC1=H or LC2=L LC2=L 8 ohms EXT8CH_INPUT Other than those LC1=L LC1=L on the above LC2=L LC2=H

IMP SW/POWER LIMIT/ IMP: PL: IC520 1355V/256 IC520 135IC5056 LC1 7 LC2 Value for starting limiter operation Value for canceling limiter operation 184 184 J model = 184 U, C, R, T, K, A, B, G, L models = 163 J model = 184 U, C, R, T, K, A, B, G, L models = 163 157 157 157 157

K0/K1 (Panel key of main unit) [Remote control code: ] A/D of the key fails to function properly when the standard value is deviated by 4%. In this case, check the constant of partial pressure resistor, solder condition, etc. Refer to table 2. (Reference voltage: 5V=100%)

K0/K1 A/D4% 2 5V=100%

[Table 2]Display 00+2 102 202 302 402 502 602 702 802 902 100 K0 PRESET/TUNING PRESET/TUNING PRESET/TUNING FM/AM MEMORY TUNING MODE RDS MODE RDS EON PTY MODE PTY START KEY OFF K1 KEY OFF SPEAKERS A SPEAKERS B INPUT MODE A/B/C/D/E PURE DIRECT TONE CONTROL EFFECT KEY OFF KEY OFF KEY OFF


FAN DRIVE TEST HIGH

FAN DRIVE TEST HIGH

FAN DRIVE TEST MID

FAN DRIVE TEST MID

37

RX-V1500/DSP-AX1500

FAN DRIVE TEST (For models so equipped) LOW

FAN DRIVE TEST LOW

13. V CONV STATUSThe data received from the video conversion IC (TA1270) is displayed. LOW BYTE DATA The status information of TA1270 is displayed in the binary notation.

13. V CONV STATUSIC TA1270 LOW BYTE DATA TA12702

Horizontal lock judgment / 0: LOCK 1: UN-LOCK Vertical standard discrimination / 0: STANDARD 1: NON-STANDARD Vertical frequency / 0: 50Hz 1: 60Hz X'tal mode / X'tal 00: 01: 4.43 10: 11: 3.58 Color system / 00: B/W 01: SECAM 10: PAL 11: NTSC Power ON reset / 0: RESISTER PRESET 1: NORMAL

HIGH BYTE DATA Not applied to this model.

HIGH BYTE DATA


38

RX-V1500/DSP-AX1500

14. IF STATUS (Input function status)Using the sub-menu, the status data is displayed one after another in the hexadecimal notation. During signal processing, the status before execution of this menu is maintained. * Numeric values in the figure example are for reference. IS1-2 (Internal status): Indicates the status information of the microprocessor.

14. IF STATUS16

IS 1-2 :

5th byte 4th byte 3rd byte 2nd byte 1st byte Digital input/output setting value Upper 4 bits: REC OUT selected / lower 4 bits: INPUT selectedValue 0 1 2 3 4 6 8 9 A Choice NONE OPT A OPT B OPT C OPT D OPT F COAX A COAX B COAX C

1 4bit REC OUT / 4bit INPUTPreset name V-AUX CD DVD D-TV CBL/SAT CD DVD DVR/VCR2

Fs information of reproduction signalDisplay Fs (kHz) 00 Analog 01 32 02 44.1 03 48 04 64 05 88.2 06 96

2Fs0A Unknown NRM 0B Unknown DBL 0C Unknown QUAD 0D Not defined

A u d i o c o d e m o d e i n f o r m a t i o n o f reproduction signalDisplay Audio Code 00 01 MULTI MONO 1+1 02 1/0 03 2/0 04 3/0 05 2/1 06 3/1

307 2/2 08 3/2 09 2/3 0A 3/3 0B 0C OVER 6.1 MULTI PCE 0D Unknown

Format information of reproduction signal *1: Analog processing used for digital reproduction is not possible because of a commercial bit or 4-ch audio reason.Display 00 01 10 20 21 22 23 50 51 54 58 5C 60 C0 C1 C4

4 *1: 4ch

Signal format Analog (Unlock) Incorrect digital (*1) PCM Audio Digital Data IEC1937 Data None PCM Unknown dts Red dts dts-ES MATRIX dts-ES DISCRETE dts-ES (Both flag) AAC Dolby Digital D.D. Karaoke D.D.6.1 (D.D.EX)


39

RX-V1500/DSP-AX1500

Signal processing status information *2: With digital signals other than 32kHz, 44.1kHz and 48kHz, through processing method is used for reproducible signals.bit7 bit6 bit5 bit4 MUTE request Red dts flashing 6.1/EX processing FULL MUTE (ON: 1)

5 *2: 32kHz44.1kHz48kHz

bit3

bit2 Through & bypass (*2) bit1 bit0 dts analog mute

CS1-5: Indicates channel status information of the input signal (IEC60958).

CS 1-5: IEC60958

BS1-7: Indicates information of the bit stream included in the dts signal.

BS1-7: dts

TI1-2:

TI1-2:

MTT: Mute Trigger

MTT: Mute Trigger

Byte No. 1 2 3 4 5

Function Mute condition Factor of the last mute Error count of YSS930-FSCNT Mute count by YSS930-FSCNT Error factor of down load of CS49329


40

RX-V1500/DSP-AX1500

15. DSP RAM CHECKThis menu is used to self-diagnose whether or not the bus connection for the YSS930 and the external RAM is made properly. During signal processing, the status before execution of this menu is maintained. The address bus and the data bus are checked and the connection condition is displayed. When no error is detected, "NoEr" appears on display. YSS930 Bus Check

15. DSP RAM CHECKYSS930RAM NoEr YSS930 BUS CHECK

Display WAIT NoEr DATA RSCS ADDR

Description Bus is being checked. No error detected. Data bus shorted or open. /RAS or /CAS shorted, or open. Address bus shorted or open.

WAIT NoEr DATA RSCS ADDR

/RAS /CAS

SECOND DECODER (DA601) BUS CHECK

SECOND DECODER (DA601) BUS CHECK

Display

Boot

Description Booting of DA601 being executed (When booting is continued, possibility is that there is a defective part or poor connection of the microprocessor DA601 SDRAM.) Booting of DA601 has been completed properly.

Boot NoEr

DA601 DA601 SDRAM DA601

NoEr

16. PROTECTION SETNot applied to this models.

16. PROTECTION SET


41

RX-V1500/DSP-AX1500

17. SOFT SWThis menu is used to switch the function settings on P.C.B. through the software so as to activate the product. The protection function follows the P.C.B. settings. When connected to AC or in the maker preset state, the unit is initialized to the P.C.B. setting. Display of each function after initialization varies depending on settings on P.C.B. The operation mode can be changed by selecting the sub-menu and then using the STRAIGHT key. With SOF selected for the SW mode, the settings become effective. SW MODE PCB or SOFT can be selected.

17. SOFT SWP.C.B. P.C.B.AC P.C.B. P.C.B. STRAIGHTSWSOFT

SW MODE PCBSOFT

MODEL SETTING V1500 only.

MODEL SETTING V1500

TUNER DESTINATION J, UC, AG or RL can be selected.

TUNER DESTINATION JUCAGRL

TUNER EXIST NOT or EXIST can be selected.

TUNER EXIST NOTEXIST

RDS EXIST NOT or EXIST can be selected.

RDS EXIST NOTEXIST

ZONE 2 EXIST NOT or EXIST can be selected.

ZONE 2 EXIST NOTEXIST

VIDEO FORMAT NTSC or PAL can be selected.

VIDEO FORMAT NTSCPAL


42

RX-V1500/DSP-AX1500

18. MICROPROCESSOR INFORMATIONThe version, checksum and the port specified by the microprocessor are displayed. The signal is processed using EFFECT OFF. The checksum is obtained by adding the data at every 16 bits for each program area and expressing the result as a 4-figure hexadecimal data.

18. 6 OFF 164 16

Version / Release 4 figure / Communication 1 figure / Boot manufacturer 1 figure / Boot 232C 1 figure OPE/DSP Version / OPE/DSP Main 2 figures / DSP 2 figures Checksum / A : All area P : Program area Checksum / 2 : Boot 232C M : Boot manufacturer Check of port setting for judging microprocessor function Display of AAC function detection port state AAC PORT:0 0 0 0 0 0 0 0 bit 7 6 5 4 3 2 1 0 Model type 0 (*1) Model type 1 (*1) Tuner mode 0 (*2) Tuner mode 1 (*2) Tuner with (1) / without (0) RDS with (1) / without (0) ZONE2 with (1) / without (0) VIDEO format: PAL (1) / NTSC (0) *2 (Tuner mode)Tuner mode 0 0 0 1 1 Tuner mode 1 0 1 0 1 Tuner frequency AM: 531-1611kHz/9kHz FM: 76.0-90.0MHz/100kHz AM: 531-1611kHz/9kHz FM: 87.5-108.0MHz/50kHz AM: 530-1710kHz/10kHz FM: 87.5-107.9MHz/200kHz R destination, Port6: LOW AM: 530-1710kHz/10kHz FM: 87.5-108.0MHz/100kHz HIGH AM: 531-1611kHz/9kHz FM: 87.5-108.0MHz/50kHz

*1 (Model type)Type 0 Type 1 0 0 Model type V1500


43

RX-V1500/DSP-AX1500

I AMP ADJUSTMENT / Confirmation of Idling Current of Amp Unit Right after power is turned on, confirm that the voltage across the terminals of R319 (Main Lch), R320 (Main Rch), R325 (Center), R326 (SURROUND Lch), R327 (SURROUND Rch), R321 (SURROUND BACK Lch), R322 (SURROUND BACK Rch) are between 0.1mV and 10.0mV. If it exceeds 10.0mV, open (cutoff) R291 (Main Lch), R292 (Main Rch), R295 (Center), R296 (Surround Lch), R297 (Surround Rch), R293 (Surround Back Lch), R294 (Surround Back Rch) and reconfirm the voltage. Attention If the idle current exceeds 10.0mV after an amplifier repair, first check for a defective component before cutting the bias resistor. Confirm that the voltage is 0.2 mV ~ 15.0 mV after 60 minutes.

R319 MAIN Lch R320 MAIN Rch R325 CENTER R326 SURROUND Lch R327 SURROUND Rch R321 SURROUND BACK Lch R322 SURROUND BACK Rch 0.1mV10.0mV 10mVR291 MAIN Lch R 2 9 2 M A I N R c h 2 9 5 C E N T E R 2 9 6 R R SURROUND Lch R297 SURROUND Rch R293 SURROUND BACK Lch R294 SURROUND BACK Rch 10.0mV 600.2mV15.0mV

0.1mV ~ 10.0mV (DC)

0.1mV ~ 10.0mV (DC)

R319 (MAIN Lch) R320 (MAIN Rch) R325 (CENTER)

R326 (SURROUND Lch) R327 (SURROUND Rch) R321 (SURROUND BACK Lch) R322 (SURROUND BACK Rch)

Cut off R291 (MAIN Lch) R292 (MAIN Rch) R295 (CENTER) R296 (SURROUND Lch) R297 (SURROUND Rch) R293 (SURROUND BACK Lch) R294 (SURROUND BACK Rch)


44

RX-V1500/DSP-AX1500

MAIN (2) P. C. B. MAIN (3) P. C. B.R291 R321 R319 R292 R322 R320 R294

R293

R325

POWER (3) P. C. B.

R326

R327

R296 R295

R297


MAIN (4) P. C. B.

45

RX-V1500/DSP-AX1500

I DISPLAY DATAG V901 : 17-BT-23GNK (WD507500)

y

1

PATTERN AREA

G PIN CONNECTION Pin No. 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34

Connection F2 NX NP NP P37 P36 P35 P34 P33 P32 P31 P30 P29 P28 P27 P26 P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 Pin No. 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Connection P9 P8 P7 P6 P5 P4 P3 P2 P1 NC NC NC 17G 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP NX F1Note : 1) F1, F2 ..... Filament 2) NP ..... No pin 3) NC ..... No connection 4) NX ..... No extened Pin 5) 1G ~ 17G ..... Grid

G GRID ASSIGNMENT17G 16G 15G

1G

2G 3G

4G

5G 6G

7G 8G

9G 10G 11G 12G 13G 14G

(17G~15G)S1 S2

S3

S4

S5

S6

S7

S8

S9

S10

S11

S12

S13

S14

(1G~14G)1-1 2-1 3-1 4-1 5-1 1f 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1e 1a 1b 1g 1c 1d

(15G)2a 2f 2b 2g 2e 2c 2d 3f 3e s20 3d S18 3a 3g 3b 3c

(17G)

S15 S16 S18 S17

S19

1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6

S20


1-7 2-7 3-7 4-7 5-7 B1

B2

46

RX-V1500/DSP-AX1500

G ANODE CONNECTION 17G P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 P36 P37 B1 B2 S15 S16 S17 S18 S3 S1 S4 S5 16G S2 S6 S7 S8 S9 S10 S11 S12 S13 1a 1b 1c 1d 1e 1f 1g 2a 2b 2c 2d 2e 2f 2g 3a 3b 3c 3d 3e 3f 3g S20 S14 15G 14G~2G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 1G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7RX-V1500/ DSP-AX1500

5-7 S19

47

RX-V1500/DSP-AX1500

I IC DATAIC509: LC89057W-VF4-E (DSP P.C.B) Digital Audio Interface TransceiverRERR INT CKST AUDIO/VO EMPHA/UO DGND DVDD XIN XOUT XMCK DVDD DGND

DO DI CE CL XMODE DGND DVDD TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 TXO/PIOE

37 38 39 40 41 42 43 44 45 46 47 48

36 35 34 33 32 31 30 29 28 27 26 25

LC89057W-VF4-E

24 23 22 21 20 19 18 17 16 15 14 13

SDIN SLRCK SBCK RDATA RLRCK DVDD DGND RBCK RMCK AGND AVDD LPF

1 2 3 4 5 6 7 8 9 10 11 12

EMPHA/UO

AUDIO/VO

RXOUT *RX0 RX1 RX2 RX3 DGND DVDD *RX4 RX5/VI *RX6/UI DVDD DGND

*: Pull-down resistor internal

32

33

35

40

39

38

RXOUT 1 RX0 RX1 RX2 RX3 RX4 RX5/VI RX6/UI2 3 4 5 8 9 10 24

Cbit, Ubit Input Selector

Microcontroller I/F

XMODE41 37 36

INT

CE

CL

CI

DO RERR RDATA SDIN RMCK RBCK RLRCK SBCK SLRCK

Demodulation & Lock Detect

Data Selector

21

LPF 13 TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO344 45 46 47

PLL Clock Selector

Modulation & Parallel Port

1/N

16 17 20 22 23

TXO/PIOEN 4829 28 27 34

XMCK

XOUT


48

CKST

XIN

RX-V1500/DSP-AX1500

IC509: LC89057W-VF4-E (DSP P.C.B) Digital Audio Interface TransceiverNo. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Name RXOUT RX0 RX1 RX2 RX3 DGND DVDD RX4 RX5/VI RX6/UI DVDD DGND LPF ACDD AGND RMCK RBCK DGND DVDD RLRCK RDATA SBCK SLRCK SDIN DGND DVDD XMCK XOUT XIN DVDD DGND EMPHA/UO AUDIO/VO CKST INT RERR DO DI CE CL XMODE DGND DVDD TMCK/PIO0 TMCK/PIO1 TLRCK/PIO2 TLRCK/PIO3 TXO/PIOEN I/O O Is I Is Is Function Input bi-phase selection data output pin TTL-compatible digital data input pin Coaxial-compatible digital data input pin with built-in amplifier TTL-compatible digital data input pin TTL-compatible digital data input pin Digital GND Digital power supply TTL-compatible digital data input pin TTL-compatible digital data / Validity flag input pin for modulation TTL-compatible digital data / User data input pin for modulation PLL digital power supply PLL digital GND PLL loop filter connection pin PLL analog power supply PLL analog GND R system clock output pin (256fs, 512fs, XIN, VCO) R bit clock input/output pin Digital GND Digital power supply R LR clock input/output pin (fs) Serial audio data input pin S bit clock output pin (32fs, 64fs, 128fs) S LR clock output pin (fs/s, fs, 2fs) Serial audio data input pin Digital GND Digital power supply Oscillation amplifier output pin Crystal resonator connection output pin Crystal resonator connection, external supply clock input pin (24.576 MHz or 12.288 MHz) Digital power supply Digital GND Emphasis information / U data output / Chip address setting pin Non-PCM output / V flag output / Chip address setting pin Clock switch transition period signal / Demodulation master or slave function switch pin Microcontroller interrupt output / Modulation or general-purpose I/O switch pin PLL clock error, data error flag output Microcontroller I/F read data output pin (3-state) Microcontroller I/F write data input pin Microcontroller I/F chip enable input pin Microcontroller I/F clock input pin System reset input pin Digital GND Digital power supply Modulation 256fs system clock input / General-purpose I/O input/output pin Modulation 64fs bit clock input / General-purpose I/O input/output pin Modulation fs clock input / General-purpose I/O input/output pin Modulation serial audio data input / General-purpose I/O input/output pin Modulation data output / General-purpose I/O enable input pin

Is Is Is

O

O O/I

O/I O O O Is

O O I

I/O I/O I/O I/O O O Is Is Is Is

I/O I/O I/O I/O O/I


1) Input/output I or O = -0.3 to 3.6V, Is = -0.3 to 5.5V 2) Pins 32 and 33 are latch address setting input pins when pin 41 = "L". 3) Pin 34 is a demodulation function master or slave setting input pin when pin 41 = "L". 4) Pin 35 is a modulation function or general-purpose I/O function switch setting input pin when pin 41 = "L". 5) Perform ON/OFF for all power supplies with the same timing as a latch-up countermeasure.

49

RX-V1500/DSP-AX1500

IC512: D601A002PYP180 (DSP P.C.B) DecoderDigital Signal Processors EMIF32 McASP1 McASP0 McBSP1 McBSP0Pin Multiplexing

L2 Cache/ Memory 4 Banks 64K Bytes Total (4-Way)

L1P Cache Direct Mapped 4K Bytes Total

C67xTM CPU Instruction Fetch Instruction Dispatch Control Registers Control Logic Test In-Circuit Emulation Interrupt Control

I2C1 I2C0 Timer 1 Timer 0 GP1 GP0 HPI16

Enhanced DMA Controller (16 channel)

L2 Memory DA610: 192K Bytes DA601: 64K Bytes

Instruction Decode Data Path A A Register File Data Path B B Register File

.L1t .S1t .M1t .D1

.D2 .M2t .S2t .L2t

R2 ROM 512K Bytes Total

L1D Cache 2-Way Set Associative 4K Bytes Total Clock Generator, Oscillator and PLL x4 through x25 Multipliers /1 through /32 Dividers

Power-Down Logic

No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Name GP0[4]/(EXT_INT4) GP0[6]/(EXT_INT6) CVDD VSS DVDD GP0[5]/(EXT_INT5) GP0[7]/(EXT_INT7) CLKS1 DVDD VSS CVDD TINP1/AHCLKX0 TOUT1/AXRO[4]/AXR1[11] CVDD VSS CLKX0/ACLKX0 TINP0/AXRO[3]/AXR1[12] TOUT0/AXRO[2]/AXR1[13] ACLKR0 AXRO[1] AFSX0 CVDD VSS AFSR0 DVDD VSS AXRO[0] AHCLKR0 CVDD VSS FSX1 DX1 CLKX1 VSS CVDD CLKR1 DR1 FSR1 VSS CVDD

I/O IOZ IOZ S GND S IOZ IOZ I S GND S I O S GND IOZ I O IOZ IOZ IOZ S GND IOZ S GND IOZ I S GND IOZ O/Z IOZ GND S IOZ I IOZ GND S

Function General purpose I/O0 port 4 General purpose I/O0 port 6 1.2V power supply Ground 3.3V power supply General purpose I/O0 port 5 General purpose I/O0 port 7 McBSP1 external clock source 3.3V power supply Ground 1.2V power supply Timer 1 Input Timer 1 Output 1.2V power supply Ground McASP0 Transmission BCLK Timer 0 Input Timer 0 Output McASP0 Reception BCLK McASP0 Transmission/reception data 1 McASP0 Transmission LRCLK 1.2V power supply Ground McASP0 Reception LRCLK 3.3V power supply Ground McASP0 Transmission/reception data 0 McASP0 Reception MCLK 1.2V power supply Ground McBSP1 Transmission Frame Sync (Input in SPI slave state) McBSP1 Transmission data McBSP1 Transmission clock (Input in SPI slave state) Ground 1.2V power supply McBSP1 Reception clock McBSP1 Reception data McBSP1 Reception Frame Sync Ground 1.2V power supply


50

RX-V1500/DSP-AX1500

IC512: D601A002PYP180 (DSP P.C.B) DecoderNo. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 Name SCL0 SDA0 CVDD DVDD VSS CVDD DVDD VSS VSS CVDD CVDD VSS CVDD VSS DVDD ARDY /CE3 DVDD VSS CVDD /CE2 EA2 EA3 EA4 DVDD VSS CVDD EA5 EA6 EA7 EA8 DVDD VSS EA9 /SDRAS EA10 ECLKOUT ECLKIN /SDCAS CVDD VSS CLKOUT2/GP0[2] /SDWE DVDD VSS EA11 DVDD VSS CVDD EA14 EA13 EA16 EA12 EA15 EA18 CVDD VSS DVDD I/O IOZ IOZ S S GND S S GND GND S S GND S GND S I O/Z S GND S O/Z O/Z O/Z O/Z S GND S O/Z O/Z O/Z O/Z S GND O/Z O/Z O/Z O/Z I O/Z S GND O/Z O/Z S GND O/Z S GND S O/Z O/Z O/Z O/Z O/Z O/Z S GND S Function 12C0 clock 12C0 data 1.2V power supply 3.3V power supply Ground 1.2V power supply 3.3V power supply Ground Ground 1.2V power supply 1.2V power supply Ground 1.2V power supply Ground 3.3v power supply Asynchronous RAM Ready input For external memory area, Enable 3 3.3V power supply Ground 1.2V power supply For external memory area, Enable 2 For external memory, Address 2 For external memory, Address 3 For external memory, Address 4 3.3V power supply Ground 1.2v power supply For external memory, Address 5 For external memory, Address 6 For external memory, Address 7 For external memory, Address 8 3.3V power supply Ground For external memory, Address 9 Asynchronous RAM OE / SDRAM RAS / SBS RAM OE For external memory, Address 10 Clock output for EMIF Clock input for EMIF Asynchronous RAM RE / SDRAM CAS / SBSRAM ADS 1.2V power supply Ground Half clock output of device Speed Asynchronous RAM WE / SDRAM WE / SBSRAM WE 3.3V power supply Ground For external memory, Address 11 3.3V power supply Ground 1.2V power supply For external memory, Address 14 For external memory, Address 13 For external memory, Address 16 For external memory, Address 12 For external memory, Address 15 For external memory, Address 18 1.2V power supply Ground 3.3V power supply


51

RX-V1500/DSP-AX1500

IC512: D601A002PYP180 (DSP P.C.B) DecoderNo. 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 Name EA17 EA19 EA20 /CE0 /CE1 CVDD CVDD VSS DVDD /BE1 EA21 /BE0 ED13 ED15 ED14 DVDD VSS CVDD ED11 ED12 ED9 ED10 ED6 ED7 ED8 CVDD VSS DVDD ED4 ED5 ED3 ED2 ED1 ED0 CVDD VSS GP0[1] BUSREQ /HOLDA /HOLD AFSR1 ACLKR1 DVDD VSS AXR1[0] AXR1[1] AXR1[2] AXR18[3] AXR1[4] VSS CVDD AXR1[5] AXR1[6] AXRO[8]/AXR1[7] ACLKX1 AMUTE1 AFSX1 GP0[0] I/O O/Z O/Z O/Z O/Z O/Z S S GND S O/Z O/Z O/Z IOZ IOZ IOZ S GND S IOZ IOZ IOZ IOZ IOZ IOZ IOZ S GND S IOZ IOZ IOZ IOZ IOZ IOZ S GND IOZ O/Z O/Z I IOZ IOZ S GND IOZ IOZ IOZ IOZ IOZ GND S IOZ IOZ IOZ IOZ OZ IOZ IOZ Function For external memory, Address 17 For external memory, Address 19 For external memory, Address 20 For external memory area, Enable 0 For external memory area, Enable 1 1.2V power supply 1.2V power supply Ground 3.3V power supply For external memory, Byte Enable Control 1 For external memory, Address 21 For external memory, Byte Enable Control 0 For external memory, Data 13 For external memory, Data 15 For external memory, Data 14 3.3V power supply Ground 1.2V power supply For external memory, Data 11 For external memory, Data 12 For external memory, Data 9 For external memory, Data 10 For external memory, Data 6 For external memory, Data 7 For external memory, Data 8 1.2V power supply Ground 3.3V power supply For external memory, Data 4 For external memory, Data 5 For external memory, Data 3 For external memory, Data 2 For external memory, Data 1 For external memory, Data 0 1.2V power supply Ground General purpose I/O0 port 1 For external memory, Bus request output For external memory, Hold request approval to host For external memory, Hold request from host McASP1 reception LRCLK McASP1 reception BCLK 3.3V power supply Ground McASP1 transmission/reception data 0 McASP1 transmission/reception data 1 McASP1 transmission/reception data 2 McASP1 transmission/reception data 3 McASP1 transmission/reception data 4 Ground 1.2V power supply McASP1 transmission/reception data 5 McASP1 transmission/reception data 6 McASP1 transmission/reception data 7 McASP1 transmission BCLK McASP1 MUTE output McASP1 transmission LRCLK General purpose I/O0 port 0 (SPI ready signal output Active: H)


52

RX-V1500/DSP-AX1500

IC512: D601A002PYP180 (DSP P.C.B) DecoderNo. 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 Name CVDD VSS AHCLKX1 GP0[8] AHCLKR1 DVDD VSS GP0[3] GP0[9] GP0[10] GP0[11] GP0[12] CVDD VSS CVDD GP0[13] GP0[14] GP0[15] NMI /RESET CVDD OSCIN OSCOUT OSCVSS OSCVDD VSS DVDD CLKOUT3 EMU1 EMU0 TDO DVDD VSS CVDD TDI TMS TCK VSS CVDD CVDD /TRST RSV2 PLLG RSV0 PLLV PLLHV RSV1 CLKIN CLKMODE0 DVDD VSS CVDD I/O S GND IOZ IOZ IOZ S GND IOZ IOZ IOZ IOZ IOZ S GND S IOZ IOZ IOZ I I S I O GND S GND S O IOZ IOZ O/Z S GND S I I I GND S S I O/Z A A A A I I I S GND S Function 1.2V power supply Ground General purpose I/O0 port 8 HPI data pin 8 McASP1 reception MCLK 3.3V power supply Ground General purpose I/O0 port 3 General purpose I/O0 port 9 General purpose I/O0 port 10 General purpose I/O0 port 11 General purpose I/O0 port 12 1.2V power supply Ground 1.2V power supply General purpose I/O0 port 13 General purpose I/O0 port 14 General purpose I/O0 port 15 Nonmaskable Interrupt edge Device reset 1.2V power supply Xtal input, Oscillation: 12 to 25MHz Xtal output Xtal GND internal connection Xtal 1.2V power supply internal connection Ground 3.3V power supply Programmable clock output up to 32 division of PLL JTAG emulation pin 1 (1k PD when boundary scanning) JTAG emulation pin 0 (1k PD when boundary scanning) JTAG Data Out 3.3V power supply Ground 1.2V power supply JTAG Data In JTAG Mode Select JTAG Clock Ground 1.2V power supply 1.2V power supply JTAG Reset Reserved (unconnected) Analog GND for PLL Reserved (unconnected) Analog 1.2V power supply for PLL Analog 3.3V power supply for PLL Reserved (unconnected) Clock input PLL input clock selection: Clkin or Xtal 3.3V power supply Ground 1.2V power supply


53

RX-V1500/DSP-AX1500

IOPORT19~0

SCK

/CS

SO

SI

SDBCKO

VSS XO XI IOPORT0 IOPORT1 IOPORT2 IOPORT3 IOPORT4 IOPORT5 IOPORT6 IOPORT7 AVSS CPO AVDD VDD1 (NC) IOPORT8 IOPORT9 IOPORT10 IOPORT11 IOPORT12 IOPORT13 IOPORT14 IOPORT15 VDD2MICROPROCESSOR INTERFACE PROGRAM RAM 50 bit 1024 word COEFFICIENT RAM 16 bit 1024 word ADDRESS RAM 17 bit 256 word CONTROL REGISTERMPLOAD

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

VSS RAMA11 RAMA12 RAMA13 RAMA14 RAMA15 RAMA16 RAMA17 VDD1 /CS SO SI SCK /IC SDWCK SDBCK SDI7 SDI6 SDI5 SDI4 SDI3 SDI2 SDI1 SDI0 VDD2

75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

VDD2 RAMA10 RAMA9 RAMA3 RAMA4 RAMA2 RAMA5 VDD1 RAMA1 RAMA6 RAMA0 RAMA7 RAMA8 RASN RAMOEN RAMWEN CASN RAMD15 RAMD14 RAMD13 VDD1 RAMD12 RAMD11 RAMD10 VSS50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26

IC516, 518: YSS930 (DSP P.C.B.) DSP

76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

VDD2 RAMD9 RAMD8 RAMD7 RAMD6 RAMD5 RAMD4 RAMD3 RAMD2 RAMD1 RAMD0 VDD1 IOPORT19 IOPORT18 IOPORT17 IOPORT16 SDO7 SDO6 SDO5 SDO4 SDO3 SDO2 SDO1 SDO0 VSS

CONTROL SIGNALS

SDBCK SDWCK

WCKOP ZEROF7R-0L


SDI0 SDI1 SDI2 SDI3 SDI4 SDI5 SDI6 SDI7

OVF END

BCKOP

SDWCKO

32 bit DSP Core

SDO0 SDO1 SDO2 SDO3 SDO4 SDO5 SDO6 SDO7

DSP INTERNAL OPERATING CLOCK CK (30.72~40.96MHz) PLL

EXTERNAL RAM INTERFACE

RAMD15~0

54

RAMA17~0

CASN RASN RAMWEN RAMOEN

CPO

XO

XI

SDO INTERFACE

SDI INTERFACE

DATA RAM 32 bit 1024 word

RX-V1500/DSP-AX1500

IC516, 518: YSS930 (DSP P.C.B.) DSPNo. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Name VSS XO XI IOPORT0 IOPORT1 IOPORT2 IOPORT3 IOPORT4 IOPORT5 IOPORT6 IOPORT7 AVSS CPO AVDD VDD1 (NC) IOPORT8 IOPORT9 IOPORT10 IOPORT11 IOPORT12 IOPORT13 IOPORT14 IOPORT15 VDD2 VSS SDO0 SDO1 SDO2 SDO3 SDO4 SDO5 SDO6 SDO7 IOPORT16 IOPORT17 IOPORT18 IOPORT19 VDD1 RAMD0 RAMD1 RAMD2 RAMD3 RAMD4 RAMD5 RAMD6 RAMD7 RAMD8 RAMD9 VDD2 VSS RAMD10 RAMD11 RAMD12 VDD1 RAMD13 I/O O I I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O A I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O O O O O O O O O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O FunctionDigital ground terminal Terminal for connecting crystal oscillator Terminal for connecting crystal oscillator (12.288 15.0MHz) General purpose input/output terminal, SDO0 Lch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO0 Rch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO1 Lch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO1 Rch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO2 Lch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO2 Rch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO3 Lch zero-flag output terminal, input/output terminal for branching program conditions General purpose input/output terminal, SDO3 Rch zero-flag output terminal, input/output terminal for branching program conditions Analog ground terminal (for PLL) Terminal for connecting PLL filter +2.5V digital power supply (for PLL) +3.3V digital power supply (for input/output terminal) (Unconnected) General purpose input/output terminal, SD04 Lch zero-flag output terminal General purpose input/output terminal, SD04 Rch zero-flag output terminal General purpose input/output terminal, SD05 Lch zero-flag output terminal General purpose input/output terminal, SD05 Rch zero-flag output terminal General purpose input/output terminal, SD06 Lch zero-flag output terminal, input terminal 0 for chip address setting General purpose input/output terminal, SD06 Rch zero-flag output terminal, input terminal 1 for chip address setting General purpose input/output terminal, SD07 Lch zero-flag output terminal, input terminal 2 for chip address setting General purpose input/output terminal, SD07 Rch zero-flag output terminal, input terminal 3 for chip address setting +2.5V digital power supply (for internal circuit) Digital ground terminal PCM output terminal PCM output terminal PCM output terminal PCM output terminal PCM output terminal PCM output terminal PCM output terminal PCM output terminal General purpose input/output terminal, overflow detect output terminal General purpose input/output terminal, program end detect output terminal General purpose input/output terminal, 64fs clock output terminal General purpose input/output terminal, fs clock output terminal +3.3V digital power supply (for input/output terminal) Data input/output terminal 0 for external memory Data input/output terminal 1 for external memory Data input/output terminal 2 for external memory Data input/output terminal 3 for external memory Data input/output terminal 4 for external memory Data input/output terminal 5 for external memory Data input/output terminal 6 for external memory Data input/output terminal 7 for external memory Data input/output terminal 8 for external memory Data input/output terminal 9 for external memory +2.5V digital power supply (for internal circuit) Digital ground terminal Data input/output terminal 10 for external memory Data input/output terminal 11 for external memory Data input/output terminal 12 for external memory +3.3V digital power supply (for input/output terminal) Data input/output terminal 13 for external memory

IC516, 518: YSS930 (DSP P.C.B.) DSPNo. 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Name RAMD14 RAMD15 CASN RAMWEN RAMOEN RASN RAMA8 RAMA7 RAMA0 RAMA6 RAMA1 VDD1 RAMA5 RAMA2 RAMA4 RAMA3 RAMA9 RAMA10 VDD2 VSS RAMA11 RAMA12 RAMA13 RAMA14 RAMA15 RAMA16 RAMA17 VDD1 /CS SO SI SCK /IC SDWCK SDBCK SDI7 SDI6 SDI5 SDI4 SDI3 SDI2 SDI1 SDI0 VDD2 I/O I+/O I+/O O O O O O O O O O O O O O O O O O O O O O O Is Ot Is Is Is I Is I I I I I I I I FunctionData input/output terminal 14 for exte

Documents

YAMAHA RXV1500