Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Summary
1:22 scale Bell 206 B3 r/c helicopter on OMP M2 mechanics
Hobby & Makers > RC & Robotics
bell206 rchelicopter
The fuselage front and rear shells and the tail boom are set to 1mm thickin the stls. I printed the front and rear fuse, tail boom, and horizontal stab'on end', and the vertical stab and ARB lying flat. My best fuselage printswere rotated 9.5 degrees from the vertical so that the flange along thesplit line is horizontal and at the top of the print (nose down for the frontshell and tail down for the rear). All parts can be printed in either PLA orPETG, but PETG is less brittle and works better for the landing skidespecially. The landing skid can be printed as one whole piece (landing-skid file) or as individual pieces (all the 'skid-xxx' files are parts) and thenglued together. All holes are present in the STLs, but it is a good idea touse a drill bit on them before tapping. Items required: Drill bits: 1.2mmfor 1.6mm bolts and 1.6mm for 2mm bolts pre tap, 2mm for untapped,2.5mm for main motor bolt holes. 1.6 and 2mm taps 1.6 x 6mm bolts areused for the ARB, servos and vertical stab (12) 2 x 8mm and 2 x 10mm forskid/frame attachment (4 of each, longer bolts for rear attachment) 6mmdia magnets (4) Tail and main motor bolts from M2 (standard size) 684ZZbearing OMP M2 motors, rotor head, shaft, FC and servos Note that therear servo has been rotated axially by 90 degrees from the standard M2
g g monkey
Bell 206B3
VIEW IN BROWSER
updated 13. 11. 2020 | published 13. 11. 2020
3D M
ODEL
ONLY
Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES
33.7 KBupdated 13. 11. 2020
39.7 KBupdated 13. 11. 2020
28.8 KBupdated 13. 11. 2020
132.6 KBupdated 13. 11. 2020
513.9 KBupdated 13. 11. 2020
325.9 KBupdated 13. 11. 2020
2.0 MBupdated 13. 11. 2020
location.It is mounted on the right hand side of the frame behind the right aileronservo (and parallel to it).The ARB bolts onto the top of the frame, so it is easier to install andreplace.There is also 'clean access' through the frame to the rear main motor boltfrom above, so it can be easily removed.
arb.stl
dog-house-stencil-right.stl
dog-house-stencil-left.stl
boom-fuselage-joint.stl
main-frame.stl
horizontal-stab.stl
landing-skid.stl
3.8 MBupdated 13. 11. 2020
5.9 MBupdated 13. 11. 2020
406.9 KBupdated 13. 11. 2020
127.4 KBupdated 13. 11. 2020
2.4 MBupdated 13. 11. 2020
508.4 KBupdated 13. 11. 2020
12.4 KBupdated 13. 11. 2020
309.8 KBupdated 13. 11. 2020
877.8 KBupdated 13. 11. 2020
fuselage-front.stl
fuselage-rear.stl
vertical-stab.stl
swash-leveller.stl
tail-boom.stl
skid-left-joint.stl
skid-step.stl
skid-lower-skid.stl
skid-rear-leg.stl
508.4 KBupdated 13. 11. 2020
849.4 KBupdated 13. 11. 2020
The Author has not uploaded any print files.Try to search in User print files section or generate and upload yourown.
License
This work is licensed under a Creative Commons (4.0 International License)
Attribution-NonCommercial
✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition
skid-right-joint.stl
skid-front-leg.stl