XX 0.25 GI VX-MOUNTING - Fresnel Tech Sheets/PIR Arrays/XX0.25GIVX.pdfXX 0.25 GI VX The lens arrays of Fresnel Technologies’ XX 0.25 GI VX series shown in the accompanying data sheets

XX

0.2

5 G

I VX The lens arrays of Fresnel Technologies’ XX 0.25 GI VX series shown in the accompanying data sheets are in-

tended to be used in passive infrared motion detector devices. They are optimized for dual-element pyroelectric detectors; the CM types are also optimized for quad-element pyroelectric detectors with this arrangement:

The other members of the series are also optimal for quad-element pyroelectric detectors of the type:

The flanged and -NF packages are suitable for both TO-5 (tall) and TO-39 (short) pyroelectric detector cans; they must be pushed onto the pyroelectric detector far enough for the face of the detector to seat on the surface indicated in Figures 2 and 4, and the spacers shown in Figures 2 and 4 are recommended to be placed between the pyroelectric detector and the circuit board. The -SMD package variant is intended for use with surface mounted pyroelectric detectors, which need no spacer; its mounting geometry is shown in Figures 5 and 6. Please be sure to note the position within the package of the surface mounted detector you are using, as differ-ent manufacturers place the elements differently relative to the package.

Figures 9 to 23 illustrate the beam patterns for the arrays. Each lens array’s beam pattern is dependent on the alignment of the 3 Roman numerals on the lens array to the pyroelectric detector’s tab or the corresponding orientation of the surface mounted pyroelectric detector, as shown in Figures 1, 3, 7, and 8. Each data sheet in-dicates our suggested mounting alignment for each different beam pattern.

The figures postulate a dual-element or quad-element detector with a 110° acceptance angle and a mounting height of 1 meter (3 feet) for the types designed AA (Animal Alley), 1.3 meters (4 feet) for the WS (Wall Switch) types, 1 or 1.3 meters for the VB (Vertical Barrier) types, and 2.5 meters (8 feet) for the CM (Ceiling Mount) types.

It is reasonable to expect CM detection of full body motion over a diameter of 8 meters (26 feet), small hand motion over a diameter of 6.5 meters (22 feet) from a mounting height of 3 meters (10 feet); a diameter of 11 meters (36 feet) for full body motion, and 5 meters (16 feet) for small hand motion from a mounting height of 5.2 meters (17 feet), using a quad-element pyroelectric detector.

Similarly, AWV3 can be expected to cover an aisle 15 meters (45 feet) long x 1.7 meters (5.5 feet) wide from a mounting height of 5.2 meters (17 feet), 15 meters (44 feet) long from a mounting height of 6.7 meters (22 feet), 11 meters (36 feet) long from a mounting height of 8 meters (26 feet), and 10 meters (32 feet) long from a mount-ing height of 10 meters (32 feet), with a good-quality dual-element pyroelectric detector.

VB V4 can be expected to cover up to a distance of 4.6 meters (15 feet) from the unit for full-body motion, 2.7 meters (9 feet) for small hand motion with a dual-element pyro electric detector. WS V4 will cover an area 7 meters (23 feet) deep by 8 meters (26 feet) wide for full-body motion, 3.7 meters (12 feet) deep by 5 meters (16 feet) wide for small hand motion with a dual-element pyroelectric detector.

171211

f© Copyright Fresnel Technologies, Inc. 2012-17

CM 0.25 GI V1

CM 0.25 GI V2

CM 0.25 GI V3

CM 0.25 GI V4

CM 0.25 GI V5

WS AA 0.25 GI V1

WS AA 0.25 GI V2

WS VB AW 0.25 GI V3

WS VB AW 0.25 GI V4

www.fresneltech.com

AA

Lens slots that fit onto a pyroelectric detector's tab are

labeled l, ll and lll

Figure 1

XX 0.25 GI VXMounting Geometry(Spacers are required - see Figure 2)

Slots labeled l, ll and lll

SlotsRunner - next to symbol II

101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817)926-7146fresnel technologies inc. drawing and design 2012

Ribs holdlens in place

on pyroelectric detector can

9.0 mm

SECTION A-A

2.5 mm

2.8 mm

Figure 2

XX 0.25 GI VXTO-39 (short) and TO-05 (tall) Pyroelectric Mounting Geometry

SECTION A-A

TO-39 CAN

Surface

SECTION A-A

TO-5 CAN

Surface

Ø

Spacer

11.2 mm

2.5 mm

3.6 mm

4.6 mm

Spacer1.5 mm


3.0 mm 3.9 mm

2.8 mm10.7 mm

8.7 mmØ

Figure 3

XX 0.25 GI VX-NFMounting Geometry(Spacers are required - see Figure 4)

AA

SlotsIdentifying Marks

Labled 1, ll and lll


Ribs holdlens in place

on pyroelectric detector can

Figure 4

XX 0.25 GI VX-NFTO-39 (short) and TO-05 (tall) Pyroelectric Mounting Geometry

9.0 mm

SECTION A-A

SECTION A-A

Surface

SECTION A-A

TO-5 CAN

Surface

Ø

3.6 mm

4.6 mm

Spacer1.5 mm


2.5 mm

2.8 mm 11.2 mm

3.9 mm3.2 mm

2.9 mm10.7 mm

TO-39 CAN

Spacer2.5 mm

8.7 mmØ

Figure 5

XX 0.25 GI VX-SMDMounting Geometry


Crush ribs hold lens in place

Sensitive elements are not in the center of the

package on all Surface Mounted

Detectors

Figure 6

XX 0.25 GI VX-SMDMounting Geometry

101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817)926-7146

TOP VIEW

A-A

SECTION A-A

1.3mm

Plane of the pyroelectric detector's sensitive elements

9.8mm D9mm D

8.7mm

7.8mm

6mm R

2.2mm2.8mm

5.3mm

2.8mm

fresnel technologies inc. drawing and design 2016

25.5°

Figure 7

XX 0.25 GI VX-SMDMounting Geometry - Circuit Board


Orientation-1

Floor

Ceiling

Lens outline for reference only

Orientation-2

Floor

Ceiling

9.9 mm diameter0.1 mm offset

from pins


from pins


9.9 mm diameteroffset 0.1 mm

from pins

1.2 mm wide(2x circuit board cutouts for pins)


from pins


Figure 8

XX 0.25 GI VX-SMDMounting Geometry - Circuit Board


Orientation-3

Floor

Ceiling


Orientation-4

Aisleway Direction


from pins8.6 mm diameter

0.1 mm offset from pins




from pins8.6 mm diameter

0.1 mm offset from pins


2.4m (8ft)

0m(0ft)

4.5m (15ft)

4.5m (15FT)

0m(0ft)

CL

4.5m (15FT)

4.5m (15FT)

0m(0ft)

CL

2.25m (7.5FT)

2.25m (7.5ft)

Figure 9

CM 0.25 GI V1

CM 0.25 GI V1-NF:

Lens Array detail

Lens Array detail

CM 0.25 GI V1-SMD:

With Flange

No Flange

Surface Mounted Detector


SIDE VIEW:

TOP VIEW:

CM 0.25 GI V1

Lens Array detail: See Figure 7, Orientation 1

2.4m (8ft)

2.4m (7.9ft)

2.4m (7.9ft)

0m(0ft)

4.5m (15ft)

4.5m (15FT)

SIDE VIEW:

0m(0ft)

4.5m (15FT)

4.5m (15FT)

0m(0ft)

CL

2.0m (6.5ft)

2.0m (6.5ft)

CL

CM 0.25 GI V2:

CM 0.25 GI V2-NF:

Lens Array detail

Lens Array detail

Figure 10

CM 0.25 GI V2-SMD:

With Flange

No Flange



TOP VIEW:

CM 0.25 GI V2


TOP VIEW:

2.4m (8ft)

2.4m (7.9ft)

2.4m (7.9ft)

0m(0ft)

4.5m (15ft)

4.5m (15FT)

SIDE VIEW:

0m(0ft)

4.5m (15FT)

4.5m (15FT)

0m(0ft)

CL

2.0m (6.5ft)

2.0m (6.5ft)

CL

CM 0.25 GI V3:

CM 0.25 GI V3-NF:

Figure 11

CM 0.25 GI V3-SMD:

With Flange

No Flange



CM 0.25 GI V3


Lens Array detail

Lens Array detail

Figure 12

101W. MORNINGSIDE DR. FORT WORTH, TX 76110, U. S. A. (817) 926-7474, FAX:(817)926-7146fresnel technologies inc. 2017

2.4m (8ft)

0m(0ft)

4.5m (15ft)

4.5m (15FT)

0m(0ft)

CL

4.5m (15FT)

4.5m (15FT)

0m(0ft)

CL

2.25m (7.5FT)

2.25m (7.5ft)

3.0m(10ft)

4.5m (15FT)

drawing and design

With Flange

No Flange


CM 0.25 GI V4:

CM 0.25 GI V4-NF:

Lens Array detail

Lens Array detail

CM 0.25 GI V4-SMD:

TOP VIEW:

SIDE VIEW:

CM 0.25 GI V4


2.4m (8ft)

0m(0ft)

4.5m (15ft)

4.5m (15FT)

0m(0ft)

CL

4.5m (15FT)

4.5m (15FT)

0m(0ft)

CL

2.25m (7.5FT)

2.25m (7.5ft)

Figure 13

CM 0.25 GI V5

CM 0.25 GI V5-NF:

Lens Array detail

Lens Array detail

CM 0.25 GI V5-SMD:

With Flange

No Flange



SIDE VIEW:

TOP VIEW:

5.8m (19ft)

5.8m (19ft)

CM 0.25 GI V5


1.2m (4ft)

6.1m (20ft)

0m(0ft)

5m(16.2)

0m(0ft)

5m(16.4ft)

CL180°

WS AA 0.25 GI V1:

WS AA 0.25 GI V1-NF:

Lens Array detail

Lens Array detail

Figure 14

WS AA 0.25 GI V1

With Flange

No Flange


WS AA 0.25 GI V1-SMD:


TOP VIEW:

SIDE VIEW:

For WS (wall switch) pattern, put pyroelectric detector's tab in slot I.


1.2m (4ft)

6.1m (20ft)

0m(0ft)

5m(16.2)

0m(0ft)

5m(16.4ft)

CL180°

18°

WS AA 0.25 GI V1:


Lens Array detail

Lens Array detail

Figure 15

With Flange

No Flange

Surface Mounted DetectorWS AA 0.25 GI V1-SMD:


TOP VIEW:

SIDE VIEW:

WS AA 0.25 GI V1For AA (animal alley) pattern, put pyroelectric detector's tab in slot III.


1.2m (4ft)

7.6m (25ft)

0m(0ft)

10m(32.8ft)

5m(16.2)

0m(0ft)

5m(16.4ft)

10m(32.8ft)

CL 120°

WS AA 0.25 GI V2:


Lens Array detail

Lens Array detail

Figure 16

WS AA 0.25 GI V2

With Flange

No Flange




TOP VIEW:

SIDE VIEW:

For WS (wall switch) pattern, put pyroelectric detector's tab in slot III.


1.2m (4ft)

7.6m (25ft)

0m(0ft)

10m(32.8ft)

5m(16.2)

0m(0ft)

5m(16.4ft)

10m(32.8ft)

CL

18°

120°

WS AA 0.25 GI V2:


Lens Array detail

Lens Array detail

Figure 17

WS AA 0.25 GI V2

With Flange

No Flange




TOP VIEW:

SIDE VIEW:

For AA (animal alley) pattern, put pyroelectric detector's tab in slot III.


1.2m (4ft)

9.1m (30ft)

0m(0ft)

10m(32.8ft)

5m(16.2)

0m(0ft)

5m(16.4ft)

10m(32.8ft)

CL

18°

120°

WS VB AW 0.25 GI V3:

WS VB AW 0.25 GI V3-NF:

Lens Array detail

Lens Array detail

Figure 18

With Flange

No Flange


WS VB AW 0.25 GI V3-SMD:


TOP VIEW:

SIDE VIEW:

WS VB AW 0.25 GI V3For WS (wall switch) pattern, put pyroelectric detector's tab in slot I or III.


6.7m (22ft)

6.7m (22ft)

0m(0ft)

5m(16.4ft)

5m(16.4ft)

CL



Lens Array detail

Lens Array detail

Figure 19

With Flange

No Flange




TOP VIEW:

SIDE VIEW:

WS VB AW 0.25 GI V3

0m(0ft)

9.1m (30ft)

0m(0ft)

2.4m(8ft)

2.4m(8ft)

98°

For VB (vertical barrier) pattern, put pyroelectric detector's tab in slot II.




Lens Array detail

Lens Array detail

Figure 20

With Flange

No Flange

Surface Mounted DetectorWS VB AW 0.25 GI V3-SMD:


SIDE VIEW:

WS VB AW 0.25 GI V3

2.4m (8ft)

4.6m (15ft)

9m (30ft)

7.6m (25ft)

4.6m (15ft)

4.6m (15ft)

8m (26ft)

8m (26ft)

1.5m (5ft)

1.5m (5ft)

For AW (aisleway) pattern, put pyroelectric detector's tab in slot I or III.


TOP VIEW:

Aisleway direction

1.2m (4ft)

7.6m (25ft)

0m(0ft)

5m(16.2)

0m(0ft)

5m(16.4ft)

CL

18°

180°



Lens Array detail

Lens Array detail

Figure 21

With Flange

No Flange




TOP VIEW:

SIDE VIEW:

WS VB AW 0.25 GI V4For WS (wall switch) pattern, put pyroelectric detector's tab in slot I or III.


Figure 22


TOP VIEW:

SIDE VIEW:

WS VB AW 0.25 GI V4

0m(0ft)



Lens Array detail

Lens Array detail

With Flange

No Flange



5m(16.2)

0m(0ft)

5m(16.4ft)

CL

2.4m(8ft)

2.4m(8ft)

For VB (vertical barrier) pattern, put pyroelectric detector's tab in slot II.


Crush ribs

Figure 23


TOP VIEW:

SIDE VIEW:

WS VB AW 0.25 GI V4

2.4m (8ft)

4.6m (15ft)

8m (27ft)

CL 1m (3ft)

1m (3ft)



Lens Array detail

Lens Array detail

With Flange

No Flange

Surface Mounted DetectorWS VB AW 0.25 GI V4-SMD:

5m(16.2)

0m(0ft) 5m

(16.4ft)

For AW (aisleway) pattern, put pyroelectric detector's tab in slot I or III.


Aisleway direction

Documents

XX 0.25 GI VX-MOUNTING - Fresnel Tech Sheets/PIR Arrays/XX0.25GIVX.pdfXX 0.25 GI VX The lens arrays of Fresnel Technologies’ XX 0.25 GI VX series shown in the accompanying data sheets