IMPORTANTDO NOT RETURN THIS BATTING CAGE TO THE RETAIL STORE WHERE

PURCHASED. CALL TOLL FREE: (800) 492-9334

IMPORTANT WARRANTY WARNING:DO NOT LEAVE THE XTENDER CAGE ASSEMBLED DURING STRONG WINDS, HEAVY SNOW, SLEET,

OR ICE STORMS. THE XTENDER IS NOT DESIGNED TO WITHSTAND EXTREME WEATHERCONDITIONS AND DAMAGE TO THE FIBERGLASS FRAMES CAUSED BY EXTREME WEATHER

MAY NOT BE COVERED IN THE MANUFACTURERS WARRANTY.

WARNING:USE THIS PRODUCT WITH ADULT SUPERVISION ONLY. SERIOUS BODILY INJURY MAY OCCUR!

READ WARNING LABELS CAREFULLY.

Home Batting Cage

Assembly Instructions

95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: 435-688-0741

Xtender30’Xtender30’

®

Part# A-2 (Quantity 1) - 44" Long - End & Middle Pole Assemblies Fiberglass Rod with Foam Pad

Part# F - (Quantity 6) Ground Stake

Part# D (Quantity 6) - 44" Long - End & Middle Pole Assemblies 1.25" Steel Tube with Foam Pad

Part# B-1 (Quantity 2) - 44" Long - End Pole Assembly Metal Fitting/Ring & Fiberglass Rod with Foam Pad & Rope Tie Stake

Part# C (Quantity 6) - 44" Long - Middle Pole Assembly Metal Fitting/Ring & Fiberglass Rod with Foam Pad & Swedged Tubular End & Rope Hook Tie

Part# E (Quantity 2) - 14' LongBlack Rope with Loop on the End

Part# G - (Quantity 1) Roll Of Black Tape

Part# H - (Quantity 1) Batting Cage Net

Part# B-2 (Quantity 3) - 44" Long - Middle Pole Assembly Metal Fitting/Ring & Fiberglass Rod with Foam Pad & Rope Hook Tie

Part# I - (Quantity 4) Rope Stake

(This Clips To The Hole In Part# I Rope Stake)

(This Clips To The Hole In Part# I Rope Stake)

(These Clip To The Rings On Part#’s B & B-1)

(These Clip To The Rings On Part# A-1)

Part# A-1 (Quantity 2) - 44" Long - End & Middle Pole Assemblies Fiberglass Rod with Foam Pad

Part# B (Quantity 4) - 44" Long - End Pole Assembly Metal Fitting/Ring & Fiberglass Rod with Foam Pad & Rope Tie Stake

PARTSLIST

Page 2

15 Feet

15 Feet

15 Feet

15 Feet

12 Feet

12 Feet

12 FeetPart# F

Part# F

Part# F

Part# F

Part# F

Part# F

STEP 1: Pound Ground Stake (Part# F) Into Ground 12 Feet Apart From Each Other (6X). Note: Make Sure Stakes Are Perfectly Straight Up And Down.

Page 3

Model# XT30

Do Not Return This Product To The Store.Call Toll Free: 1-800-492-9334 For Customer Service.

Part# A-1Part# BPart# CPart# D Part# B Part# C Part# DPart# B-1

Part# G

STEP 2: End Pole Assemblies (Quantity 2) (Refer to Part #’s Below.)

Page 4

Tape each section together with Black Tape.

Slide each section together and tape together. Repeat for the second End Pole Assembly.

Part# A-2Part# B-2Part# CPart# D Part# B-2 Part# B-2 Part# C Part# D

Part# G

STEP 3: Middle Pole Assembly (Quantity 1) (Refer to Part #’s Below.)

Tape each section together with Black Tape.

Slide each section together and tape together.

Model# XT30

STEP 5: Lift End Pole Assembly vertically and slide Part# D of End Pole Assembly over Ground Stake (Part# F).

End Pole Assembly (2X)

End Pole Assembly (2X)Middle Pole Assembly (1X)

STEP 4: Clip Net Support Ropes to Rings on End Pole Assembly (2X). Page 5

Net SupportRopes (4X)

End PoleRings (4X)

End PoleRings (4X)

Net SupportRopes (4X)

Part#D OfEnd PoleAssembly

End PolePart#D (6X)

Ground StakePart#F (6X)

STEP 6: Bend End Pole Assembly into an arc & slide the other end of Part# D over Part# F (Ground Stake). Note: Repeat for Middle Pole Assembly and the other End Pole Assembly.

Caution: Excessive bending will break Pole Assembly. Exercise caution when bending pole assemblies.

Part#F(Ground Stake)

Clip Rope (4X) to Rings on End Pole Assembly.Repeat for other end.

Stabilizer Rope

STEP 7: Hammer Rope Stake (Part# I) into ground and clip Stabilizer Rope into Rope Stake hole (6X). Make sure rope is tight.

Page 6

Pound Part#I (Rope Stake) into ground and clip stabilizer rope through hole in Ground Stake. Make sure Stabilizer Rope takes the slack out of Net Support Ropes.

Repeat for all (4) corners.

(1)

(2)

(3)

(4)

Part# I(Rope Stake)

Rope Clip

Stabilizer Rope

Net Support Rope(s)

Net Support Rope(s)

Caution: Excessive wind can cause frame assembly to collapse. Make sure Stabilizer Ropes are secure at all times and take down in stormy weather.

Page 7

Attach Part# E To Poles.

(Both Sides.)

STEP 8: Where Part# D And Part# C join together (Middle Pole Assembly), wrap straight end of Part# E (Black Rope With Loop) around Middle Pole Assembly joint, slip through Part# E Loop and pull tight.

Wrap straight end of Part# E (Black Rope with Loop) around joint of Part# D and Part# C (End Pole Assembly), pull tight, and tie a knot.

Slide straight end of Part# E (Black Rope with Loop) through loop and pull tight.

Wrap straight end of Part# E (Black Rope with Loop) around joint of Part# D and Part# C, pull tight, and tie a knot.

Joint of Part# D and Part# C.

Wrap straight end of Part# E (Black Rope with Loop) around joint of Part# D and Part# C, Slide straight end of Part# E (Black Rope with Loop) through loop of Part# E and pull tight.

Step: A-1

Step: A-2

Rope LoopRope Knot

Note: Attach Part#E to Pole section at the opposite end of the pitching machine. This provides more support for the area where the hitter stands.

Batting Cage Net Harness Tubeson the Top Sideand Bottom Sideof Net Frame.

INCORRECTNOTE:If batting cage harness isincorrect, you have put onthe batting cage net inside out.Please take o� batting cagenet and reverse. Put inside ofnet to the outside of the cage and the outside of the net tothe inside of the cage.

Batting Cage Net Harness Tubeson the Left Side and Bottom Sideof Net Frame.

CORRECT

Tubes should be sticking out of Batting Cage.

STEP 9: Unfold Part# H (Batting Cage Net) and lay out long ways on the ground. Gently begin placing Part# H (Batting Cage Net) over the assembled frame.

Page 8

Important: Un-clip Stabilizer Rope from Part# I (Rope Stake). Slide Rope & Clip inside the Batting Cage, then out through an opening in the top of the Batting Cage Net. Re-clip to Part# I (Rope Stake) so the Batting Cage Net hangs straight down instead of hanging over the Stabilizer Ropes.

Model# XT30

Heater Batting Cage Net Harness Tubes

STEP 10: Slide Batting Cage Harness Tubes (2X) Into Pitching Machine Harness Tubes And Lock Into Place With Push Pins.

Page 9

WARNING Make sure Heater Sports Pitching Machine is turned off and unplugged when attaching

Batting Cage Net Harness Tube toHeater Sports Pitching Machine.

OPTIONAL ACCESSORY (Sold Separately):You can purchase any Heater Pitching Machine product to attach to the Xtender Home Batting Cage.Call Toll Free: 1-800-492-9334 to locate a retail store near you.

WARNING!• Never allow a batter in the Batting Cage until the Heater Sports Pitching Machine has been sighted in and pitching at the desired target and at the right speed.• Make sure Heater Sports Pitching Machine is turned off and unplugged when attaching the Batting Cage Net Harness Tube to the Trend Sports Pitching Machine.• Make sure and disassemble the Xtender Batting Cage in stormy weather. The cage could break or blow over and cause property damage. • Make sure area around bat- ting cage is clear of people except for batter and machine operator. Bodily injury could occur if proper safety pre- cautions aren’t followed.

95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: 435-688-0741

IMPORTANTDO NOT RETURN THIS BATTING

CAGE TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE:

(800) 492-9334.

®

Page 1

Step #1Fully assemble both batting cages

and place them end-to-end4 -2 inches apart.

Batting Cage #1

Batting Cage #2

Optional:Joining 2 Cages

(Must purchase 2 separate cages)INSTRUCTIONS

Xtender30’Xtender30’