Embed Size (px)
Citation preview
XPL+ Biodegradable Downhole Drilling
Fluid Additive Technology and Products is
designed to reduce Heat and Friction
under the Most Extreme Conditions
Based in Orange County California
With offices in Houston, Texas.
Manufacturers ProOne Inc
World Headquarters
Earth Friendly
Technologies
50 Times More Powerful
Than Typical Lubricants
Typical
Lubricants
Charge - + Bonding/flowing Flowing Bonding
Reaction to heat & pressure
Migrates away Migrates towards
Film strength Limited Extraordinary
Environmentally friendly
No Yes
Characteristic
50 Times More Powerful
200,000psi 4,000psi
Without XPL+ With XPL+
Compare
85
88.5%
5
93%
Oil & Gas Customers/Partners
• NOV - National Oilwell Varco
• Newfield
• Nabors
• Encana
• Sandridge
• Sinclair Well Products
• Panther Energy
• Occidental
• M-PactDownhole Motors
• Newpark Resouces
• Hess Inc.
• Helis Oil & Gas
• Continental
• Texas United/TBC-Brinadd
90 barrel mixing vats
with Invert Diesel
Drilling Fluid
Mixing valves to load
from the vats to the
mud pumps
ProOne Downhole
Drilling Fluid drums
emptied into the vats
Results:
Cooled the pumps by +30°
Helped reduce fluids that were
bypassing the seals within
hours.
Mixing the ProOne Downhole Drilling
Fluid into the cooling pumps
ROP increases to 239’ per hour from 48’ ROP by
adding 4 drums (5%) of the ProOne DownHole
Drilling Fluid to the Invert Diesel Drilling Fluid at 6,259.72’
After the ProOne Downhole Drilling Fluid
is out of the system, the ROP returns to
the 48’ per hour ROP with the Invert
Diesel Drilling Fluid at 8,269.42’
Results
Newfield Test Results
1/19/2011
• The torque was in the 12,000 to 13,000 range
and gradually reduced to the 10,000 to 11,000
range approximately 20 minutes after ProOne
hit the bit.
• Torque reductions and pressure continues to
drop using the ProOne Drilling Fluid
Results
The Newfield company man quoted:
“This is the first time they have been able to complete a
lateral of this length with only one mud motor and one
bit….saving a trip out, a mud motor and a bit.”
Completed 6000’ lateral without tripping the line.
• Same drill bit!
• Same mud motor!
• 25% faster!
Savings
Saves Mud
Pumps, Mud
Motors & Drill
Bits
20-50%
Reduction in
Torque & Drag
Improve
Rate of
Penetration
Less
Corrosion
&
Wear
Increase
Lubricity
Easier
Steering
&
Sliding
Over
70%
Reduction
In Friction
Savings
based on a 30-day month
Based on proven results we have seen to date in North Dakota, the following cost savings
can be expected in a typical well with the use of ProOne Drilling Fluid.
We have used conservative numbers that we believe are not only achievable but will in
most cases be exceeded. Savings are based on a 30-day month.
Savings:
20% increase in R.O.P. (Rate of Penetration)
= 6 days @ $80,000 per day = $480,000
1 trip for the vertical = 1 day @ $80,000 per day = $80,000
1 trip for the lateral = 1 days @ $80,000 per day = $80,000
2 drill bits @ $25,000 ea = $50,000
2 mud motors @ $7,000 = $14,000
Total savings = $704,000
Directions
18 drums in an 800 barrel system
@ $2,150 per drum = $38,700
Less replaced Lateral Lube III drill lubricant
= 24 drums @ $1,200 = $28,800
Net incremental cost to use ProOne Drilling
Fluid = $38,700-$28,800 = $9,900 total cost
ROI = $704,000-$9,900
= $694,100 net savings
(not counting drill string repair savings)
Directions
Mix at a ratio of 5% to the volume through
slug pit concentration, then treat the entire
pit at 3%.
Water base muds
Oil-base muds
Brine solutions
Can be used with:
Important:
MANUFACTURING
FACILITIES
Southern
California
Available for Review:
• Test reports, Case Studies & results
• Non-Toxic test results
• Material Safety Data Sheets
www.pro-one.co.za
1
CONTACT US Full-XBrands LLC
250 Vista Blv Suite 103
Sparks
NV 89434
George Fullard: 775-527-6901
Email: [email protected]
Website: www.fullxbrands.com
