XDMs

SURVEYBefore Installation of an XDM equipment, one should check the following.

1 Rack2 Power Supply3 Grounding4 Temperature5 Physical Dimension

6 Physical location

Materials required for installing XDM1 Power Cable2 Lugs3 Insulation tape4 Conduit pipe5 Cage Nut6 Spirals7 Lables8 Tie9 Nuts & Bolts

10 Anchor Fastner11 L Clamp

Tool Kits Required for installation1 Crimping tools2 tie cutter3 Scissors4 multimeter5 Screw Drivers6 Krone tools7 Wraping tools8 Drilling machine9 Spanner set

10 Allen key11 Combination Plier

12 Long Nose Plier13 Spirit level14 Hammer15 Hexsaw & blade16 Labling machine17 Center Punch18 Jigsaw Cutter19 Measuring Tape20 FILE21 Tool Bag

Tool required for Commissioning & testing1 Laptop2 Slip Cables3 NVM adaptor4 Dongle5 Optical Power meter6 Optical variable attenu7 Fix Attenuators8 SDH Analyser9 Patch cords

10 E1 Looping cable

SURVEYBefore Installation of an XDM equipment, one should check the following.

Check whether the rack is firm & the witdh is 21 Inches or 19 InchesAvailability of Power Supply of -48V DC (-40V to -75V DC) & MCB should be required as followsMake sure that Grounding is available on the Rack.Temperature of the room should be cool enough to keep the equipment stable (15'C to 22'C)Check for availability of space in the rack.

Materials required for installing XDMPower cable as required by customer (10,16 & 25 sqmm) should bw laid from DC power sources till xRAPRing type(10,16,25sqmm) & pin type(10,16,25sqmm)… (12 Nos. each)Black, Blue, red & GreenConduit/flexible pipe to be laid for protection of power cable.For mounting equipments on the rack (16 Nos.)Spirals required for protection of patch cords to be laid bw equipment to FMS (Size as per the nos of Patch cords)required for labling the patch cords, power cable, equipment etc.required for tying the power cables, E1 cables, & lablingFor mounting rackFor mounting rackFor supporting rack

Tool Kits Required for installationFor crimping lugs & cat5For cutting tiesFor cutting Lables,For measuring the voltages of power supplyFor fitting the xRAP & Shelf on the rack & cards in the shelf For kroning E1 portsFor Wraping E1 portsHeavy Duty Drilling machine with Beads, for drilling false flooring, concrete, & metals.For fastenning the Nut & Bolts while mounting RackFor tightening Nut & BoltsFor Mounting rack

routing requirements(power cables, E1 cables,Patch Cords etc), floor loading capacity (minimum 200 Kg), Cleanliness,

For Mounting rackFor checking the level of the rackFor Mounting rackFor cutting metalsFor Printing lables as requiredFor marking drill pointFor cutting false Flooring

Tool required for Commissioning & testingFor commissioningFor connecting laptop toFor Loading Software in the NVMFor accessing additional features in XDM local login (XCs, Clock, alarm severity etc.)For ATFor ATFor ATFor ATFor ATFor AT

SURVEY

Fuse HxWxD (mm) Max Wieght (Kg)XDM40 20A 256x447x285 16XDM50 15A 130x443x231 22XDM100 20A 200x443x231 30.2XDM200 25A 275x443x231 30.2

XDM300 37AXDM400 20A 500x450x288XDM500 25A 725x450x285 60XDM1000 50A/75A 1100x450x285 70XDM2000 50A 775x450x285 60xRAP 125x450x120 10xRAP-100 133x445x185 10

Typical XDM installation Procedure

123456789

10111213141516


Prepare the installation site & Check the physical location, environmental compliance, and availability of power sourcesPrepare power, alarm, management and transmission cables at the installation site. Route the required power, alarm, management and transmission cables to the intended XDM equipment locationInstall the equipment racks, in accordance with the site installation plans.When applicable, install the EMS-XDM management station, in accordance with the site installation plansIn each rack, install the power distribution and alarm panels (xRAP) and other equipment needed, in accordance with the site installation plansInstall the XDM shelves in the appropriate racks, in accordance with the site installation plansInstall the cooling fan units under the XDM shelvesInstall the prescribed cards and modules in each XDM shelf, in accordance with the rack installation plansRoute the optical fibers among the connectors of the equipment installed in each rack, in accordance with the site installation plansConnect coaxial and multipair cables to the electrical interface modules of each XDM shelf installed in the rack, in accordance with the rack installation plansConnect management cables between the equipment installed in the racks and the management station, in accordance with the site installation plansConnect power and alarm monitoring cables from the rack power distribution and alarm panels to each equipment unit installed in the rack, in accordance with the rack installation plansConnect power, alarm and traffic cables to the new equipment racks, in accordance with the site operational proceduresPerform power-up and initialization procedures.Install the network management station and configure the equipment, in accordance with prescribed instructions


XDM 400,500 & 1000 TX XDM 400,500 & 1000 RXSr no Sr no

1 Orange brown / Green brown 1 Brown / Brown grey2 Red / Red grey 2 Blue brown / Violet brown3 Orange / Orange grey 3 Grey brown / Pink brown4 Brown red / Grey red 4 Yellow / Yellow grey5 Yellow red / Green red 5 Green / Green grey6 Blue / Blue grey 6 Blue red / Violet red7 Violet / Violet grey 7 White red / Pink red8 Brown green / Grey green 8 white / White grey9 Yellow green / Orange green 9 Pink / Pink grey

10 Brown white / Red white 10 Blue green / Violet green11 Orange white / Yellow white 11 White green / Pink green12 Brown yellow / Red yellow 12 Green white / Blue white13 Orange yellow / Green yellow 13 Violet white / Grey white14 Red brown / Yellow brown 14 Blue yellow / Violet yellow

XDM 50/100/300 TX XDM 50/100/300 RXSr no Sr no

1 Brown yellow / Red yellow 1 Brown / Brown grey2 Orange yellow / Green yellow 2 Red / Red grey3 Blue yellow / Violet yellow 3 Orange / Orange grey4 Grey yellow / White yellow 4 Yellow / Yellow grey5 Brown blue / Red blue 5 Green / Green grey6 Orange blue / Yellow blue 6 Blue / Blue grey7 Green blue / Violet blue 7 Violet / Violet grey8 Grey blue / White blue 8 White / White grey9 Brown orange / Red orange 9 Pink / Pink grey

10 Yellow orange / Green orange 10 Brown white / Red white11 Blue orange / Violet orange 11 Orange white / Yellow white12 Grey orange / White orange 12 Green white / Blue white13 Brown violet / Red violet 13 Violet white / Grey white14 Orange violet / Yellow violet 14 Red brown / Yellow brown15 Green violet / Blue violet 15 Orange brown / Green brown16 Grey violet / White violet 16 Violet brown / Blue brown17 Brown pink / Red pink 17 Pink brown / Grey brown18 Orange pink / Yellow pink 18 Brown red / Grey red19 Green pink / Blue pink 19 yellow red / Green red20 Grey pink / White pink 20 Blue red / Violet red21 Pink violet / Pink yellow 21 White red / Pink red

Software requirement for commissioning of XDM (V7187)1) NVM loader 7.02 (XDMFlash Programmer 7.02)2) LCT-XDM_V71.34

XDM 100

NVM LOADER

15) Connect slip cable to F –Channel.16) Double click Slip-Direct Connect.

18) Double click LCT-XDM 71.34

The XDM accept any value between 1 to 65535, (& it should be unique in the network)

Commissioning Procedure:-

1) Insert NVM adaptor (with NVM) or NVM in PCMCIA slot in your Laptop.2) Select the DriverèOpenèCtrl+AèShift+Delete.3) Right Click driverèProperties( Used space should be Zero)4) Click NVM Loader icon (XWFP) Current version 7.02.5) Click Addè Embedded Version NameèBrowse the path.6) Select the drive, check mark use PCMCIA, Expand Tree & Auto Compare.7) Click Start.8) After loading Embedded (There is no errors) messages comes.9) Stop the drive and remove it from laptop.10) Repeat the same if we are using two MXC 100 card.11) Insert the NVM in the MXC-100 card slot NVM.12) Remove one MXC-100card from card gauge.13) Power ON XDM 100.(MCB must be 20 A)14) Wait still system gets boot.(Only Active LED must be there)

17) Check ping response (StartèRunèping 192.9.90.1 –t).

1) User Name: xdm, Password: xdm2) Click Log in.3) Click install.4) Put IP configuration Settings IP address, NE ID, System Title, System Location, Equipment type (XDM 100/XDM1000 etc).

a. IP Configuration. i. DCC Only NE. ii. Ethernet Only NE. iii. Gateway Only NE

b. NE ID :- Last two Values of DCC IP(E.g.:-If DCC IP is 192.9.72.1, NE ID : 721 or last four digits, e.g.:- 192.9.122.155 NE ID: 22155)

5) System will get reboot, wait for some time.6) System will take IP address only, again put System title, system location etc.

Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled

(PIM2_21, PIM2_63, SIM1_4, SIM4_2, EISM_208, EISM_244).

24) DCC termination, Terminate all the Optical port with MSDCC (or RSDCC as requirement by customer)

Repeat the same for all SAM or SIM Cards.

E1 testing

Click the è Set PC Time ( The XDM 100 will set its own time as it is in your laptop's current time)7) Click Shelf view è Assign all the cards.8) Right click ECU card and assign expected type to actual type.9) Right click FCU card and assign expected type to actual type.10) Right click A1 slot èAssignèSelect the expected type matches to actual type.

a. SAM 16_1, SAM 4_2.11) Repeat the same for A2, B1 and B2.12) Right click A1 slotsèAttributesèApplication codeèselect expected type.

a. Eg: - L3, L5 or S3 matches with actual type.13) Assign I1 slot if output cards is inserted there.14) Repeat the same for I/O slots if cards were inserted.(I1 to I8 Slots)

15) Right click SAM 16_1 èDCC AllocationèSelect MS or RS èConnect.16) Repeat for all the optical cards and all the ports.17) Logout.18) Insert MXC 100 in B Slots.19) Wait still card gets properly booted.20) LoginèRight click MXC 100 AèDB SynchronizeèEquipment ProtectionèLockout releases.21) Logout èHard ResetèWait for some time.22) Right click MXC 100 A è Switch Over.23) Check for alarms.

Right Click on SAM or SIM Cards èDCC TerminationèSelect MS & connect (Select RS if the customer are using RS DCC)

Right click on PIM1_21/PIM 2_63èOpenèSelect 1 PortèRight click 2M-Snk-1èFar End Loop back.

NE ID :- Last two Values of DCC IP(E.g.:-If DCC IP is 192.9.72.1, NE ID : 721 or last four digits, e.g.:- 192.9.122.155 NE ID: 22155)


XDM 500

NVM LOADER

16) Double click Slip-Direct Connect.



Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disa


1) Insert NVM adaptor (with NVM) or NVM in PCMCIA slot in your Laptop.2) Select the DriverèOpenèCtrl+AèShift+Delete.3) Right Click driverèProperties( Used space should be Zero)4) Click NVM Loader icon (XWFP) Current version 7.02.5) Click AddèPut Embedded Version NameèBrowse the path.6) Select the drive, check mark Use PCMCIA, Expand Tree & Auto Compare.7) Click Start.8) After loading Embedded (There is no errors) messages comes.9) Stop the drive and remove it from laptop.10) Repeat the same if we are using two XMCP card.11) Insert the NVM in the XMCP card.12) Remove one XMCP card from card gauge.(C1 or C2 Slots)13) Power ON XDM 500.(MCB must be 40 A)14) Wait still system gets boot15) Connect slip cable to F –Channel.


1) User Name: xdm, Password: xdm2) Click Log in.3) Click install.4) Put IP configuration Settings IP address, NE ID, System Title, System Location, Equipment type (XDM 500x4).




Click the è Set PC Time ( The XDM 100 will set its own time as it is in your laptop's current time)7) Repeat still systems take all the details.

(PIO2_21, PIO2_84, PIO 345_16, SIO 1&4) (M2_21 B, M2_84, M345_16) Don’t insert PIO cards in IC3 & IC4 slots, only optical cards.


Repeat the same for all SAM or SIM Cards.

E1 testing

8) Click Shelf view è Assign all the cards.9) Right click XIO 192 card and assign expected type to actual type.( X1 & X2 slots)10) Right click xFCU card and assign expected type to actual type. (F1, F2, F3 Slots).11) Assign MECP card.12) Right click X1 & X2 slotsèAttributesèApplication codeèselect expected type.

a. Eg: - L3, L5 or S3 matches with actual type.13) Assign slots IC1 to IC6 if output cards are inserted there.

14) Right click XIO 192 èDCC AllocationèSelect MS or RS èConnect.15) Repeat for all the optical cards and all the ports.16) Logout.17) Insert XMCP in C2 Slot.18) Wait still card gets properly booted.19) LoginèRight click XMCP C1èDB SynchronizeèWait20) Equipment ProtectionèLockout releases.21) Logout èHard ResetèWait for some time.22) Right click XMCP è Switch Over.23) Check for alarms.

Right Click on SAM or SIM Cards èDCC TerminationèSelect MS & connect (Select RS if the customer are using RS DCC)

Right click M2_84èOpenèSelect 1 PortèRight click 2M-Snk-1èFar End Loop back.

The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network)

Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled

















































The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network)

Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled Set The parameter as Auto Link Discovery: Enabled & Others (Revertive SNCP Mode, TIM Detection J0, J1, & J2): Disabled


Click the è Set PC Time ( The XDM 100 will set its own time as it is in your laptop's current time)



NE ID :- Last two Values of DCC IP(E.g.:-If DCC IP is 192.9.72.1, NE ID : 721 or last four digits, e.g.:- 192.9.122.155 NE ID: 22155)

Set PC Time ( The XDM 100 will set its own time as it is in your laptop's current time)


XDM 1000

NVM LOADER

16) Double click Slip-Direct Connect.





1) Insert NVM adaptor (with NVM) or NVM in PCMCIA slot in your Laptop.2) Select the DriverèOpenèCtrl+AèShift+Delete.3) Right Click driverèProperties( Used space should be Zero)4) Click NVM Loader icon (XWFP) Current version 7.02.5) Click Addè Embedded Version NameèBrowse the path.6) Select the drive, check mark use PCMCIA, Expand Tree & Auto Compare.7) Click Start.8) After loading Embedded (There is no errors) messages comes.9) Stop the drive and remove it from laptop.10) Repeat the same if we are using two XMCP card.11) Insert the NVM in the XMCP card.12) Remove one XMCP card from card gauge.(C1 or C2 Slots)13) Power ON XDM 1000.(MCB must be 40 A)14) Wait still system gets boot15) Connect slip cable to F –Channel.


1) User Name: xdm, Password: xdm2) Click Log in.3) Click install.4) Put IP configuration Settings IP address, NE ID, System Title, System Location, Equipment type (XDM 1000).




Click the è Set PC Time ( The XDM 100 will set its own time as it is in your laptop's current time)7) Repeat still systems take all the details.8) Click Shelf view è Assign all the cards.9) Right click HLXC192/384/768orXIO192/384 card and assign expected type to actual type.( X1 & X2 slots)10) Right click xFCU card and assign expected type to actual type. (F1, F2, F3 Slots).

(PIO2_21, PIO2_84, PIO 345_16, SIO 1&4) (M2_21 B, M2_84, M345_16) Don’t insert PIO cards in I12 slot, only optical cards.


Repeat the same for all SIO Cards.

11) Right click xINF card and assign expected type as xINF_H12) Assign MECP card.13) Right click X1 & X2 slotsèAttributesèApplication codeèselect expected type.

a. Eg: - L3, L5 or S3 matches with actual type.14) Assign slots I1 to I12 if output cards are inserted there.

15) Right click SIO 16_2èDCC AllocationèSelect MS or RS èConnect.16) Repeat for all the optical cards and all the ports.17) Logout.18) Insert XMCP in C2 Slot.19) Wait still card gets properly booted.20) LoginèRight click XMCP C1èDB SynchronizeèWait21) Equipment ProtectionèLockout releases.22) Logout èHard ResetèWait for some time.23) Right click XMCP è Switch Over.24) Check for alarms.

Right Click on SIO Cards èDCC TerminationèSelect MS & connect (Select RS if the customer are using RS DCC)

Right click M2_84èOpenèSelect 1 PortèRight click 2M-Snk-1èFar End Loop back.

The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network)





























The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network) The XDM accept any value between 1 to 65535, (& it should be unique in the network)b. NE ID :- Last two Values of DCC IP(E.g.:-If DCC IP is 192.9.72.1, NE ID : 721 or last four digits, e.g.:- 192.9.122.155 NE ID: 22155)

The XDM accept any value between 1 to 65535, (& it should be unique in the network)NE ID :- Last two Values of DCC IP(E.g.:-If DCC IP is 192.9.72.1, NE ID : 721 or last four digits, e.g.:- 192.9.122.155 NE ID: 22155)

Documents

XDMs