WS10-1 ANSYS, Inc. Proprietary © 2009 ANSYS, Inc. All rights reserved. April 28, 2009 Inventory #002599 Workshop 10 Turbo Pre and Post Introduction to

WS10-1ANSYS, Inc. Proprietary© 2009 ANSYS, Inc. All rights reserved.

April 28, 2009Inventory #002599

Workshop 10

Turbo Pre and Post

Introduction to CFXPardad Petrodanesh.CoLecturer: Ehsan [email protected]

WS10: Turbo Pre and Post



Workshop SupplementIntroduction

A simple workshop follows to demonstrate how to use the Turbomachinery mode in CFX-Pre and CFD-Post.

This workshop models an Axial fan. The model consists of a single rotating domain for the fan blade with stationary domains upstream and downstream of the blade.

The full axial fan contains ten blades. Due to rotational periodicity a single blade passage will be modeled. Frozen Rotor interfaces are used to connect the rotating and stationary domains.




Workshop Supplement

1. Open Workbench (Start > Programs > ANSYS 12.0 > ANSYS Workbench)

2. Drag CFX into the project schematic

3. Start CFX-Pre by double clicking Setup

4. Select Tools > Turbo Mode

Turbo-Pre




Workshop Supplement

1. Set the Machine Type to Fan

2. Select Z as the Rotation Axis• Notice that the rotational axis is displayed in the Viewer

3. Click Next >

Basic Settings

The Turbo mode uses a setup wizard to walk you through CFX-Pre. The first step is the Basic Settings panel:




Workshop SupplementComponent Definition

1. Right-click in the Component Definition white space, and select Add Component…

2. Select the Type as Stationary and set the Name to S1

3. Select the Mesh File as fan.gtm

4. Expand the Available Volumes frame and select the Volumes as INBlock Main

5. Expand the Region Information frame and compare with the picture on the next page and make the necessary changes

The Component Definition panel is used to import meshes, select the rotation speed for each component and set the tip clearance (if any). Start by defining the first stationary component:





• The mesh file contains all three components, but only one of those components is to be included in S1

• Default values can be used for all other options

The Region Information is used by CFX-Pre to identify mesh regions of interest. CFX-Pre will try to automatically identify these regions, but manual input may be required depending on how the regions are named in the mesh file.

CFX-Pre will automatically create boundary conditions and domain interfaces using these regions, so checking the Region Information at this stage will save time later.





1. Right-click in the Component Definition white space, and select New Component…

2. Select Rotating and set the Name as R1

3. Set the Rotating Value to –3000 [rev min^-1]• The rotation direction is shown in the Viewer

4. Do not select a mesh file. The mesh has already been imported in the previous step. Under Available Volumes select Passage

5. Expand the Wall Configuration frame. Set Tip Clearance at Shroud to YES and Tip Clearance at Hub to NO• This sets boundary conditions for a fan with a rotating hub and a

counter-rotating shroud surface

Now define the rotating component:





6. Expand the Region Information frame and compare with the picture below and make the necessary changes

• This sets boundary conditions for a fan with a rotating hub and a counter-rotating shroud surface





1. Create a new stationary component named S2

2. Under Available Volumes select OUTBlock Main

3. Expand the Passages and Alignment frame• The number of Passages in 360 and the number of Passages

To Model is determined automatically• You can change the automatic values or apply a Theta Offset

by clicking the Edit button, but this is not necessary for this case

4. Expand the Region Information frame and compare with the picture next page and make the necessary changes

Now define the second stationary component:





5. Click Next > to proceed




Workshop SupplementPhysics Definition

1. The default Fluid, Simulation Type and Model Data are appropriate for this simulation

2. Select Boundary Template as P-Total Inlet Mass Flow Outlet• The Boundary Template provides quick setup of the most

common turbomachinery boundary combinations

3. Set P-Total to 0 [atm]

4. Set Mass Flow to Per Component and then enter a Mass Flow Rate of 0.04 [kg s^-1]

5. Set Flow Direction to Cylindrical Components with direction set to 1,0,0

All Physics settings, including Fluid Type, Simulation Type, Inlet and Outlet boundary conditions, Interface types, and Solver Parameters are set in one panel.




Workshop SupplementPhysics Definition

6. Change the Interface Default Type to Frozen Rotor

7. Expand the Solver Parameters frame

8. Set the Convergence Control to Physical Timescale with a value of 0.02 [s] (select the expression icon to allow this to be entered)• This sets the timescale to roughly 6/ω, where ω is the machine

rotational speed in [rad/s]. Typically, the timescale for rotating machinery is specified somewhere between 0.1/ω and 10/ω.

9. Click Next > to proceed




Workshop SupplementInterface Definition

1. Select each interface to verify it has been created correctly• There are two Frozen Rotor

interfaces, three Periodic interfaces and an interface near the blade tip to connect dissimilar meshes together

• The interfaces have been correctly created

2. Click Next > to continue

Interfaces are automatically created using the Region Information from the Component Definition panel.




Workshop SupplementBoundary Definition

1. Select each boundary condition to verify the settings are appropriate

2. Select Next > to continue

Boundary conditions are also automatically created using the Region Information from the Component Definition panel and information from the Physics Definition panel.




Workshop SupplementFinal Operations

1. Click Finish

The Final Operations panel allows you to Enter General Mode.

Enter General Mode is useful if you want to use other CFX-Pre features (profile boundaries, CEL etc) but still complete most of the set up using the Turbomachinery mode.




Workshop SupplementSolver and CFD-Post

1. Switch to the Projects window

2. Select File > Save

3. Enter the File name as turbo_demo.wbpj and click Save

4. Now double-click on Solution in the Project Schematic to start the Solver Manager

5. When the Solver Manager opens, click Start Run




Workshop SupplementTurbo-Post

In CFD-Post the following features will be demonstrated:

• Auto Initialize of Turbo Components• Modifying Turbo regions• Displaying Hubs and Blades using the 3D view• Create vector and contour plots using the Blade to Blade

View• Create vector and contour plots using the Meridional View• Use of Turbo Charts and Macros• Table creation and viewing using the Table Viewer




Workshop SupplementTurbo-Post GUI

1. Switch to the Projects window2. View the results in CFD-Post by double clicking Results in the

Project Schematic3. In CFD-Post, click on the Turbo tab4. Click Initialise All Components

• For each component CFD-Post detects which regions correspond to the Hub, Shroud, Blade, Inlet, Outlet and Periodic regions. CFD-Post uses this information to make turbo plots and charts. You can manually assign these regions, or check the auto-assigned regions by editing each of the component object from the Turbo tree (Component 1 (S1), Component 2 (R1) and Component 3 (S2))

5. Select the Three Views toggle• You can toggle between a Single View and Three Views. The three

views shown are a 3D view, a Blade to Blade View and a Meridional View




Workshop Supplement3D View

6. Edit the 3D View object from the Turbo tree• The Details of 3D View are shown

7. Select All Domains

8. Under Parts to Draw, select Hub and Blade

9. Toggle Show Faces on

10. Under Instancing, set Domain to R1, set # of Copies to 3 and then click Apply

11. Now set Domain to S1, set # of Copies to 3 and click Apply

12. Finally set Domain to S2, set # of Copies to 3 and click Apply• The 3D View now shows 3 copies of the Hub

and Blade in each of the 3 components




Workshop SupplementBlade-to-Blade View

Now create a Blade to Blade Vector Plot:

1. Edit the Blade-to-Blade object from the Turbo tree

2. Change Plot Type to Vector

3. Set Sampling to Equally Spaced and # of Points to 400

4. Click Apply• A Vector Plot is shown in the Blade-to-Blade View

5. Change Sampling from Equally Spaced to Vertex and click Apply• The Vector Plot now shows vectors starting from each mesh

node




Workshop SupplementBlade-to-Blade View

6. In Details of Blade-to-Blade Plot, change the Plot Type to Contour and select the Variable as Total Pressure in Stn Frame, then click Apply

7. Create a Stream plot of Velocity in the same way • Change the number of points to 100

8. Double-click on 3D View in the Turbo tree

9. Enable the Show Blade-to-Blade plot toggle and click Apply to show the blade-to-blade Stream plot in the 3D View




Workshop SupplementMeridional View

1. Edit the Meridional object from the Turbo tree

2. Generate a Contour plot of Pressure using a Local Range• A Contour plot is shown in the Meridional View

3. Now enable the Show Sample Mesh toggle (near the bottom of Details of Meridional Plot )• A mesh is now shown on the Contour plot• This illustrates the resolution used in creating the meridional

data




Workshop SupplementTurbo-Post




Workshop SupplementTurbo Charts & Macros

1. Double-click on the Inlet to Outlet object under Turbo Charts in the Turbo tree

2. Increase the number of Samples/Comp. to 20

3. Examine some of the other Turbo Charts

Turbo Charts and Macros are also available:




Workshop SupplementTables

1. Select the Table Viewer tab from the bottom of the Viewer window

2. Select the New Table icon from the Table Viewer toolbar and accept the default name

3. In cell A1 type: Mass Averaged Inlet Total Pressure

4. In cell B1, type the equation:=massFlowAve(Total Pressure)@S1 Inlet• Alternatively you can use the Table Viewer toolbar to select Insert:

Function > CFD-Post > massFlowAve, then Insert: Variable > Total Pressure, etc to build the expression

The Table Viewer allows you to create a table that can be exported in .html, .csv, or .txt formats. You can also save a state file for a table for later use. Next you will create a table and export it to an html file.





5. In cell A2 type: Mass Averaged Outlet Total Pressure

6. In cell B2, enter the equation:=massFlowAve(Total Pressure )@S2 Outlet

7. In cell A3 type: Omega

8. In cell B3, select Insert: Expression > omega or type: =omega





9. In cell A4 type: Filename

10. In cell B4, select Insert: Annotation > File Name > Name

11. Click the Save Table icon from the Table Viewer toolbar

12. Save the file as axial_table.html

13. Open this file in a web browser




Workshop Supplement

1. From the main menu select File > Report > Report Templates…

2. Select Fan Report and click Load

3. Once the report has been generated, click on the Report Viewer tab

4. Browse through the report to see what has been included

Turbo Reports

CFX Post includes automatic report generation based on templates. A number of Turbo-specific templates are available:




Workshop SupplementTurbo Report

1. Click the Comment icon from the main toolbar

2. Enter User Plots the for Name

3. Type the following in to the Comment Viewer :

You can add you own Figures, Tables, Charts and Comments to the report. Next you will add a figure to the end of the report showing a Vector plot at 50% span in the blade passage.





4. Switch to the Report Viewer, and Refresh the report• The Refresh button is in the

Report Viewer toolbar• The new comment will

appear at the end of the report





1. Switch to Turbo tab

2. Double-click Blade-to-Blade from the Turbo tree

3. Set Span to 0.5

4. Set Plot Type to Vector and Variable to Velocity

5. Click Apply

Now create a Velocity plot at 50% span:





1. Click the Figure icon from the main toolbar

2. Set the Name to Vector Midspan and click OK

3. Scroll to the bottom of the Outline tree• The Figure appears at the end of the Report

4. Switch to the Report Viewer tab and Refresh the report to see the changes

Now add this plot to you report:




Workshop SupplementTurbo Plot

1. Click the Publish icon from the Report Viewer toolbar

2. Click OK to write the HTML file• The file and figures can be distributed as necessary

Once the report is complete you can publish it to an html file




Workshop SupplementCFD-Post

1. Create various figures, tables, comments and charts that you might typically want to see in your analysis

2. Try enabling the Generate CFX-Viewer Files… toggle when publishing your report• Image in the report can then be rotated, zoomed and panned.

The CFX Viewer must be installed on the machine viewing the report; this is freely available from the Customer Portal and does not require a license (so your customers can view your figures in 3D)

You may want to try the following on your own, time permitting

Documents

WS10-1 ANSYS, Inc. Proprietary © 2009 ANSYS, Inc. All rights reserved. April 28, 2009 Inventory #002599 Workshop 10 Turbo Pre and Post Introduction to