http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Home   Sign Up!   Browse   Community   Submit

   All     Art     Craft     Food     Games     Green     Home     Kids     Life     Music     Offbeat     Outdoors     Pets     Photo     Ride     Science     Tech

Wooden Desktop Trebuchetby AcceptableRisk on July 10, 2006

Table of Contents

License:   Attribution Non-commercial Share Alike (by-nc-sa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Intro:   Wooden Desktop Trebuchet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

step 1:   Materials and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

step 2:   Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

step 3:   Cutting the Joinery - Part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

step 4:   Cutting the Joinery - Part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

step 5:   Frame Assembly - Part 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

step 6:   Frame Assembly - Part 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

step 7:   Throwing Arm Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

step 8:   Finishing It Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

step 9:   Fire! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

License:   Attribution Non-commercial Share Alike (by-nc-sa)

Intro:  Wooden Desktop TrebuchetThe trebuchet is a medieval invention originally designed to lay siege to fortresses and castles. The largest of them could hurl immense stones hundreds of yards. Nowyou can have one to play with in your own home. The whole device stands about foot tall when unloaded and flings various things ten feet or more. Moreover, this is anice introductory woodworking project that you can do with mostly basic tools. Make sure to check all of the images. A lot of the details are in the notes there.

step 1: Materials and ToolsMaterials3/8" Hardwood Square1/8" Hardwood Dowel3/16" Metal RodJumbo Craft SticksWood GlueHeavy Stuff as a Counterweight

ToolsSawMiter BoxRulerSharp Knife and/or Chisel(s)Drill with 1/8" and 3/16" Drill bitsClamps

You can really make this project out of just about any type of wood. I chose poplar because it's cheap and sturdy. Most big hardware stores will also have oak andoccasionally maple. The design is stout enough that you could make it out of something softer like basswood. In fact, it's probably not a bad idea if you don't have a sharpnarrow chisel and you're going to be carving the joints with a knife. These measurements call for just a little over six feet of it. Most 3/8" square is sold in three footpieces. You might get away with just two if you adjusted the size of a couple of parts, but you'll almost certainly have to recut a couple of pieces so you might as well justget three sticks.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

step 2: DimensionsTime to start cutting up all of that wood. We're going to need pieces of the following dimensions:

2 x 6" Long frame side rails - Part A2 x 3" Short frame sides - Part B1 x 7" Frame crossmember - Part C2 x 4.5" Frame extension rails - Part D2 x 4.75" Uprights - Part E4 x ~3.5" Long diagonal supports - Part F2 x 2.25" Short diagonal supports - Part G4 x ~1" Launch ramp support blocks - Part H1 x 7.5" Upper Arm2 x 2.25" Lower Arms

Parts D, F, and G need 45 degree miters cut on each end as shown in the picture. The length measurements are, of course, along the long side.

As for the long diagonal supports (Part F), you'll need to finely adjust the length of these in order to get them to fit nicely. Check the fourth image in step six to see what Imean. The given length of 3 1/2" should get you pretty close depending on how well you cut the frame extension rails.

The launch ramp supports (Part H) are just little bits of scrap that are angled to make a trough with craft sticks. A 45 degree cut isn't quite long enough to attractivelycradle a jumbo craft stick so the angle on those is shallower. I just eyeballed it and got something that looked nice. Putting a protractor on it shows it to be about 35degrees or so. If you don't feel like going through the trouble, you could just glue a couple of craft sticks flat on the frame to make a plank bottom and it'll work fine butwon't be quite as pretty and you'll have a little harder time lining up consistent shots.

Image Notes1. Lower Arms - 2.25"2. Long Diagonal Braces - Part F - ~3.5" along the long side - See the notesabout adjusting the length3. Long Frame Sides - Part A - 6"4. Short Frame Sides - Part B - 3"5. Upper Arm - 7.5"6. Shop Tip: Don't leave a paper container of breadstick sauce unattended onyour workbench while on vacation unless you really like fungus.7. Uprights - Part E - 4.75"8. Frame Extension Rails - Part D - 4.5" along the long side9. Frame Crossmember - Part C - 7"10. Short Diagonal Braces - Part G - 2.25" along the long side

Image Notes1. Launch Ramp Supports - Part H

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Careful, these things are sharp.

Image Notes1. Clamping a stop block in the box is helpful to ensure that duplicate parts areall the same size, especially when cutting the 45 degree miters.

Image Notes1. Frame Extension - Part D - x22. Long Frame Sides - Part A - x23. Long diagonal supports - Part F - x44. These blocks keep the axel from sliding from side to side. They're just littlestrips of craft stick glued to the sides of the uprights.

Image Notes1. Uprights - Part E - x22. Short Frame Sides - Part B - x23. Short Diagonal Braces - Part G - x24. Ramp Support - Part H - x45. Launch Ramp6. Center Frame Crossmember - Part C - x1 It goes all the way across.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Upper Arm x12. Lower Arms x2

step 3: Cutting the Joinery - Part 1We're going to employ a lap joint in the long frame rails (Part A). That involves removing half the thickness of the wood at each of the ends so the short sides havesomething to notch into. Three-eighths of an inch from each end, saw half-way through the stick. Then, using your chisel or sharp knife, cut along the grain to remove thehalf of the material at the end. You may find it easier to take a little at a time off so you can get it just right. Do the same thing to the other end on the same side.

Parts A and D need cross-lap joints (as does part C, the frame crossmember, but it's a little different so we'll get to that in a minute). To do these, we need to cut out thesame amount of wood but in the middle of the stick. Mark it out so it's right in the center. Check the photos to get the orientation right.

Image Notes1. Part A2. We're aiming to cut out this section on each end. 3/8" x 3/16"

Image Notes1. We'll cut along the line on the top down to the line on the side. Then we'll cutalong the line on the side to remove the chunk from the corner.

Image Notes1. You might want to cut a little ahead of the line so that you can come back withyour knife or chisel and clean it up real nice.

Image Notes1. Chop out the corner with a chisel or whittle it down with a sharp knife. Going alittle at a time can help prevent splitting and ensure that you get it just right.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Now we're going for this section. It's centered in the middle on both this siderail and on the frame extension part. Make sure to get the orientation right.

Image Notes1. Cut just inside the lines so you can whittle it down for a nice tight fit.

Image Notes1. These are the frame extensions (Part D). This socket is where one of theuprights will attach.

step 4: Cutting the Joinery - Part 2The frame crossmember (Part C) is going to seat across both long frame rails so it needs two sections removed. Rather than measure it all out, it's easier to just clampthe four sides of the bottom frame together and lay the crossmember in grooves in the long rails. Get it lined up by eye and mark out the sections where the railsintersect. That's where you're cross-lapping the crossmember just like the rails so mates up tightly and sits flat.

Now we're going to carve the uprights (Part E). One end will have a half-lap and the other end will have a groove carved in the end for the axle to ride in. The half-lap isjust like the ones on the side rails. For the axle groove drill a 3/16" hole about half an inch or so from the end. The next step is to clear out the wood between the hole andthe end of the upright. Cut a slot from the end to the hole so you can have a little room to get your knife in there and carve it out. Alternately, if you don't mind it beinghard to get the arm out, you can just drill a hole a little bigger and thread the axle straight through the hole.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Part C2. Clamp your frame sides together and lay the long crossmember in thegrooves.

Image Notes1. Then, mark along the intersections where you'll chop out two more grooves tomate with the ones in the rails.

Image Notes1. Hey, this is starting to actually look like something.

Image Notes1. 3/16" hole about half an inch from the end. A drill press is handy here but youcan get by otherwise.2. Half-lap just like with the side rails.3. These are the uprights (Part E)

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Cut a slot in the end to give your knife or chisel a little room to clear out therest.

Image Notes1. This is what you're aiming for. A nice U-shaped channel.

Image Notes1. Frame Crossmember - Part C - Two grooves for cross lap joints with framerails.2. Frame extension rails - Part D - Cross lap groove in the center.3. Short frame sides - Part B - No fancy cuts4. Upper arm - Nothing fancy5. Lower arms - No funny business6. Uprights - Part E - Half lap on the bottom end, 3/16" wide U-shaped channelon the top7. Short diagonal supports - Part G - Mitered corners8. This is what your parts should all look like once you've finished the cutting.Not shown: Ramp supports - Part H9. Long Diagonal Braces - Part F - Just mitered corners10. Long frame sides - Part A - Half lap on each end and a cross lap groove inthe middle.

step 5: Frame Assembly - Part 1You might be able to get away with just gluing all of the parts together but I pinned it all together with glue and poplar dowel; it's not likely to ever come apart and it adds anice visual element. Clamp together the bottom frame and drill through where ever they overlap. Get a little glue on the joint surfaces and then put a little on the end ofyour dowel. and work it into your hole and cut or break the dowel off. Once it firms up a little you can shave the leftover nub off with your knife or sand it down. I supposeif you're really bored, you could precut a bunch of little 3/8" and 3/4" lengths of dowel and tap them in. Then you wouldn't need to come back and cut them off.

Pin the uprights to the frame extension rails as shown in the picture. Now is also the time to attach the ramp supports if you've got them. My craft sticks weren't longenough to get all the way across bottom frame, so I supported it in the middle and at the rear.

Once that's all together, you can mount the uprights to the rest of the frame. The frame extension rails run right along on top of the main frame rails. Just glue and pinthem in place. Things are starting to shape up.

Image Notes Image Notes

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

1. These 1/8" diameter holes are a little more than half an inch deep. For thecross-lap joints, just drill straight through.

1. Titebond III - "The ULTIMATE wood glue."

Image Notes1. This squeeze out can be cleaned up with a wet rag.

Image Notes1. This will be the rear of the trebuchet.2. It doesn't really matter which side of the frame is the top but this joint will haveanother piece stacked on top of it so putting the crossmember on top will makethe joint look a bit nicer from the bottom.3. Part D4. These little nubs can be shaved off with a sharp tool or sanded down.

Image Notes1. You're going to need to make sure that your pin in the bottom frame here iscut or sanded flush before this step or else the frame extension rail won't sitproperly.

step 6: Frame Assembly - Part 2Now here's the tricky part: drilling and mounting the diagonal braces. It helps here to employ the buddy system in order to get a couple of extra hands or to use a bunchof clamps. Either way, try to get your pieces sturdily affixed in a temporary fashion and just drill carefully and slowly. Don't use a lot of pressure or you're likely to force itout of whack. If you've got some patience, you could glue the parts in place and let it dry before pinning.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Short Diagonal Brace

Image Notes1. Drilling the bottoms first, especially of the long braces, seems easier.

Image Notes1. Can you tell I like these clamps?

Image Notes1. The picture's a little blurry, but you can see that if you get the lengths right, youget a nice tight fit down in this corner. If your diagonals are too long there will be abit of a gap but if they're too short, they won't fit at all.

Image Notes1. A little sandpaper and a some knifework gets things looking pretty nice.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

step 7: Throwing Arm AssemblyThe arm is easy. The lower arms overlap the upper arms by about an inch and a quarter. You just need to line it up and glue it together. Then you need to drill out theaxel holes. The axels will be about an inch and a half apart. It's important that you try to get them straight up and down as much as possible. If you have access to a drillpress, I recommend you take advantage of it. You should have a little more than six inches of arm above the main axel depending on how close to the end of the lowerarm that you drilled the holes for the lower axel.

The main axels are made from 3/16" steel rod. You could use aluminum if you'd like. It'll be easier to cut but usually costs more. I suppose you could even use a woodendowel but you'll get a bit more friction. Check the distance between your uprights and cut an appropriate length of rod to serve as your primary axel. Tap it through thehole in your throwing arm. Cut another short piece to go between the lower arms to support your counterweight.

Then it's time to add the release pin. This is the business end of the trebuchet and it's important to mount the pin securely. I used a little length of wire from a jumbo paperclip as my pin. The 1/16" hole I originally drilled to accomodate my pin proved too large. Forcing a bit from a smaller paper clip into the hole along with it made for a nicetight fit. You may even get away with chucking a bit of wire right into your drill and trying to drive it directly into the end of the arm.

Image Notes1. The overlap here is about 1 1/4". The alignment isn't crucial, but get itclose.

Image Notes1. More on this later.

Image Notes1. These 3/16" holes are about 1 1/2" apart.

Image Notes1. This should be 3 3/8" or so, but go ahead and just match it up so you get a goodfit. If it's just a bit short, it'll be less likely to bind once the side blocks are in place.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Chances are you'll need some kind of blunt instrument to get the axel through.

Image Notes1. I'm not really sure why this picture turned out so blue. It's kind of weird.2. If you have the means, certainly soften the edges to get rid of any burrs.

Image Notes1. Jumbo paper clip. The shiny bit to the left is a piece of a smaller paper clipjammed in there since the hole I originally drilled was too big.

step 8: Finishing It UpCut two little strips of craft stick to glue to the sides of the uprights. This will block out the main axel and keep it from sliding from side to side. Make them a little wide soyou can trim them down just right.

Then glue down two more sticks to the ramp blocks to make a channel for your payload. If you didn't do the blocks, at least glue a couple of sticks down flat so yourprojectile doesn't get caught in the frame during launch.

You'll need a weight. It can be just about anything, coins, batteries, stones, etc. What I've found works well, though, is lead fishing sinkers. Specifically, I melted down abunch of them and put a loop of picture wire in it to make a tidy little weight. Then I sprayed it with a spray-on rubber coating to protect it and make it look nice.

The size of your weight will determine how far your treb will throw. With an eight ounce weight, it'll throw a small binder clip about ten or twelve feet at a height of aboutfour and a half feet. A twelve ounce weight gets a height of about six feet or so with a comparable increase in distance. At a pound or more, it gets to be more than youcan practically use indoors unless you're throwing things that are potentionally painfully heavy or you have very large rooms. Of course, with a heavier payload, you'llneed a heavier counterweight to get the same distance.

Once you get something together, hang your weight from the the axel between the lower arms of your trebuchet.

Finally, find something to shoot. I haven't found a design for a sling that works well at this size so I just tie a cord to whatever it is I want to chuck. A good length to startwith is about four or so inches. Experiment to find what works best with what you're trying to throw.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. Glue a little section of craft stick to the outside edges of the uprights. This willkeep the primary axel from sliding back and forth.

Image Notes1. Trim the overhang to size.

Image Notes1. Glue down two craft sticks to make the launch ramp or just glue a couple ofsticks down flat if you decided to forgo to support blocks.

Image Notes1. This is another 8 oz weight sprayed with a rubber coating and sporting a moreaccomodating hanger.2. I got four or five of these little chrome condiment cups at my local giant retailconglomerate for around a dollar. They work well for sorting parts and meltingdown various whatever.3. This is 8 oz of lead fishing weight melted down with a loop of picture wire sunkin it. The loop on this particular weight proved to be too long for this trebuchet.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. They aren't kidding. This stuff is very hot. Incidentally, propane will also workjust fine for melting lead.

Image Notes1. About four inches. You'll need more or less to get the maximum out of yourtreb but this is good to start with.2. I'll admit, using a binder clip for a projectile instead of something fancier is kindof lame but it was the first smallish thing at hand that I could tie a string to.

step 9: Fire!To fire your trebuchet, drop your arm into the uprights and hook the loop at the end of your projectile over the pin at the end of the throwing arm. Pull the arm down andplace the projectile in the trough. When you're ready to fire, release the arm.

If everything is well, your whatzit will go launching off into the near distance. If your launch didn't go so smoothly, you may be able to do a few things to help it. If yourlaunch is too high or too low, you can adjust your pin or the length of the cord on your projectile.

And there you have it. The whole thing is probably over engineered but it looks nice and works well. In fact, if you wanted to get crazy, the thing could probably hold prettymuch as much weight as you could fit though the uprights, easily five pounds or more.

Thanks for looking. This is my first Instructable so I hope it's clear enough for you to make one for yourself if you like it. Please post your comments with any feedback.

Image Notes1. Keep your sensitive bits away from this end when the machine is in motion. It'dbe bad news if you snagged an eyelid on this thing.

Image Notes1. Release quickly for the most consistent launch.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

Image Notes1. <---- Bend the pin a little this way to increase the release angle and create ahigher launch. Do this if your payload is shooting into the deck a foot from thedevice.2. You can adjust the pin to fine tune launch angle. A release angle of 45 degreeswill give you the best distance.3. ----> Bend the pin a little this way to lower the angle of release. Do this if yourpayload is hitting the ceiling before it gets its full distance.

Related Instructables

Desktoptrebuchet frombicycle frame byVisitor

How to Build aCatapult byT3h_Muffinator The Curiously

StrongTrebuchet: APocket SizedMedieval SiegeEngine byEthanal

Lego Trebuchetby ab1000

Catapults(guide) bymg0930mg

Scout Project:How to build aTrebuchet byBiggsy

Build atrebuchet in fiveminutes byaztennenbaum

How to Make aDesktop VikingCatapult (with abonus wargameto play). byKiteman

Advertisements

Comments50 comments Add Comment view all 169 comments

 brainspater says:  Dec 22, 2007. 10:00 PM  REPLYMe i use a cannon.

 Jake_C says:  May 30, 2009. 1:48 PM  REPLYbazookas are for wimps, i use laser-injected ninja super amazing rocket lazerbeam -coolwhip sword gun grenade cannons from outer space...

 jamalk says:  Jun 27, 2009. 1:09 AM  REPLYlaser-injected ninja super amazing rocket lazerbeam -coolwhip sword gun grenade cannons from outer space are for wimps i uselightsaber+force choke lol kidding

 LEDmuffin says:  Jul 15, 2009. 7:13 PM  REPLYLightsaber and force choke is for wimps, I use Shoop-da-whoops.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

 Fashim says:  Jul 23, 2009. 2:49 AM  REPLYNice.

 Jake_C says:  Jun 27, 2009. 10:14 AM  REPLYlightsaber + force choke is for wimps, i use bagels

 necropolian says:  Jun 28, 2009. 2:31 AM  REPLYbagels are for wimps, i force my enemies into spontaneous combustion.

 jokerlz says:  Jun 28, 2009. 11:52 AM  REPLYForcing enimes into spontanious combustion is for wimps, I kill them through the medium of dance.

 necropolian says:  Jun 29, 2009. 5:24 AM  REPLYmedium of dance is for wimps, I also use studio 100 music. seriously, that stuff is lethal.

 Fashim says:  Jul 23, 2009. 2:48 AM  REPLYstudio 100 music is for wimps. I use a Laser Canon Graphted to my chest that Explodes my Enemies into candy.

 necropolian says:  Jul 28, 2009. 1:06 PM  REPLYa Laser Canon Graphted to my chest that Explodes my Enemies into candy is fot total wimps. I use a strong, undetectablepoison.

 rabbitkillrun says:  Aug 12, 2009. 7:03 AM  REPLYstrong, undectable poisons are for wimps. I use long repetitive comment threads to distract my enemies while i aim mylaser cannon graphed combusting candy bagel laser-injected ninja super amazing rocket coolwhip laserbeamlightsaber sword forcechock gun grenade cannons from outer space shoop-da-whoop bazuka trebuchets...

 necropolian says:  Aug 12, 2009. 12:57 PM  REPLYyou know, all this time I do not get a comment on mine, and just as i thought this very morning : " hey, I still do nothave a comment on mine! how strange!" and, of course, I get a comment the same day. so, here it comes: longrepetitive comment threads to distract my enemies while i aim my laser cannon graphed combusting candy bagellaser-injected ninja super amazing rocket coolwhip laserbeam lightsaber sword forcechock gun grenade cannonsfrom outer space shoop-da-whoop bazuka trebuchets are for wimps... I do not use that, because I do not haveenemies...at least not enemies who know where I live, and who really am.

 dirty9774 says:  Feb 5, 2010. 2:12 PM  REPLYha, you said "forcechock"

 necropolian says:  Feb 6, 2010. 2:36 AM  REPLYNo, I copied the text from "rabbitkillrun". He made the mistake.

 corey_caffeine says:  Aug 12, 2009. 5:16 PM  REPLYnot having enemies is for wimps. I use bananas.

 rabbitkillrun says:  Aug 13, 2009. 1:13 PM  REPLYbananas are for wimps... i use pacman to eat the banana, then the big dot then eat all my enemies...

 jmitch77 says:  Sep 20, 2009. 12:16 PM  REPLYUsing pacman to eat the banana, then the big dot then eat all my enemies is for wimps. I use ChuckNorris.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

 rabbitkillrun says:  Sep 20, 2009. 1:06 PM  REPLYChuck Norris is for wimps. I eat spinach like popeye.

 superdude678 says:  Oct 20, 2009. 1:32 PM  REPLYEating spinach like popeye is for wimps. I use the Athena orbital defense network's ion cannon.muahahaha

 Ryan Riehl says:  Oct 26, 2009. 3:52 PM  REPLY Using the Athena orbital defense network's ion cannon is for wimps. I just surrender.

 rabbitkillrun says:  Oct 26, 2009. 5:17 PM  REPLYSurrendering is for wimps. I use pacman.

 tim_W says:  Oct 26, 2009. 7:27 PM  REPLY pacman is for wimps and doesn't ensure everyone's deathI use miley cyrus's party in the usa song guarenteed 100% lethal

 Fashim says:  Oct 27, 2009. 3:53 AM  REPLYmiley cyrus's party is for wimps.. I use Hand Held Midgets

 Zerg says:  Nov 12, 2009. 2:05 PM  REPLYHand held midgets are for whips...I just kill people >:)

 I ACW I NINJA says:  Jan 25, 2010. 6:17 PM  REPLYkilling people is for wimps, i spontaneously give birth through my ears

 matt_miele says:  Oct 28, 2009. 5:15 PM  REPLYmr. T pittys you all!

 therapist says:  Dec 30, 2009. 10:56 PM  REPLYccc combo breaker

 jokerlz says:  Jan 5, 2010. 11:42 AM  REPLY ccc combo breakers are for wimps. I use discarded hairstyles fromthe 50s.

 rabbitkillrun says:  Jan 4, 2010. 1:53 PM  REPLYIf you're going to ruin it, at least do it properly... <_< ffs 

 superdude678 says:  Oct 28, 2009. 6:08 PM  REPLYmy comment fells claustrophobic

 rabbitkillrun says:  Jan 4, 2010. 1:53 PM  REPLYNot as much as mine. :S 

 cdousley says:  Jan 5, 2010. 2:51 PM  REPLYThe end.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

 cdousley says:  Jan 5, 2010. 2:51 PM  REPLYthe end is for wimps i use the begining

 Ryan Riehl says:  Jan 5, 2010. 3:12 PM  REPLYThe beginning is for wimps, I use all of the above.

 rabbitkillrunsays:

 Jan 16, 2010. 11:11 AM  REPLY

All of the above is for wimps. I use my bare fists. 

 Armestamsays:

 Feb 4, 2010. 11:55 PM  REPLY

 All of the above is for wimps, I use none of theabove.

 

rabbitkillrun says:

 Feb 5, 2010. 7:00 AM  REPLY

None of the above is for wimps. I useAustralia. 

 ken247113 says:  Jun 22, 2008. 1:01 PM  REPLYjust wondering but could you scale this trebuchet up?

 daninja says:  Jul 6, 2009. 3:00 PM  REPLYsnap whackers.

 thepelton says:  Jul 10, 2009. 1:43 PM  REPLYRequired strength of the beams goes up much faster than length as you magnify the size.

 superdude678 says:  Oct 28, 2009. 4:45 PM  REPLYThere are a lot of things you left out of your materials list that you used. To make things easier for us trebuchet-builder-people, why don't you just make a biglist of all the stuff you used. Make your instructions more organized more organized.

 FallenAngels says:  Sep 23, 2009. 8:49 AM  REPLYwhat's the width of that metal rod?

 FallenAngels says:  Sep 14, 2009. 8:59 AM  REPLYit looks 3 inches to me they bigger than the lower arms which are 2.25" and smaller than part f

 FallenAngels says:  Sep 14, 2009. 8:56 AM  REPLYhow long did this take to make

 tulekah says:  Aug 23, 2009. 10:15 AM  REPLYWARNING!!! nobody seems to have mentioned that TIRE WEIGHTS contain CADMIUM to harden them. CADMIUM vapor released by melting tire weights isfar more dangerous to life than plain lead fumes. I nkow of at least two cases of near-fatal heavy metal poisoning of mountain man types casting flintlockballs from tire weights!!! Me, i used pennies for me weight, easy to fine-tune the range by adding or subtracting a handfull.

 I am Silas. says:  Sep 4, 2009. 6:35 PM  REPLYYou could also use dead batteries for weights.

http://www.instructables.com/id/Wooden-Desktop-Trebuchet/

 tulekah says:  Aug 23, 2009. 10:43 AM  REPLYAn old rule of thumb say that Free Weight Trebs FWT throw farther and Fixed Weight Trebs FXT are more accurate. In small scale is is probably irrelevant.Me I prefer fixed weight because the treb rolling back and forth after the hurl in response to the swing of the weight makes for a nice visual follow-thru. Trebscan be fine-tuned in several ways. As I said in my previous comment you can change the weight, you can also change the missile weight, the length of thesling, and the point of sling release. Also rather than using a sling (small scale slings are very difficult to tune) missiles with a loop attached to them are easyto make and tune by using a boy-scout variable knot to make the loop. A friend made a treb that threw tennis balls with a line and loop attached, his dogsretrieved the balls and the rope let her avoid dog-slobber.

 Loud1 says:  Apr 9, 2009. 5:20 PM  REPLYJust finished mine, outfitted it with about a 1 lb zinc ball and a leather sling. This beast will launch a penny 15 feet or more, pegged my boss in the foreheadwith it!

 Riojelon says:  Apr 15, 2009. 2:50 AM  REPLYhahaha! lol! He didn't fire you , didn't he?

view all 169 comments